Service Adjustments

3P51 ADJUST MENU

1.FACTORY MODE:
(1)Assembly line adjust mode: Press S.M.,

(DISPLAY) and

keys in turn to enter

this mode.
(2)Engineer adjust mode: Press CLOCK, P.M. and

keys in turn to enter this mode. This

mode is usually for R&D and engineering department use.

(3)Press digital keys to enter every adjust page, use PROG+/- keys to pick adjust items, use
VOL+/- keys to adjust the value.
(4)Press DISPLAY to quit factory mode.

2.B+ VOLTAGE ADJUST

Measure C600A + voltage, adjust VR641 to get proper B+ voltage according to CRT
assembly list requirement.

3. RF AGC VOLTAGE ADJUST

(1)Receive 294.25MHz,60dBcolor bar signal.
(2)Enter factory mode and press digital key 4.
(3)Measure tuner AGC point voltage, adjust AGC item till the voltage is 2.4V,or till picture
noise just disappearsUsually the AGC value is fixed to 27.

4 FINE ADJUST
(1) FOCUS ADJUST
a. Receive cross-hatch pattern signal
b. Set picture to RICH mode
c. Adjust FBTs FOCUS knob till picture is clear

(2) SCREEN VOLTAGE ADJUST(KEY 0 )

a. Set picture toSTANDARDmodewithout signal input;
b. Enter factory mode and press digital key0
c. Adjust FBTs SCREEN knob till VG2 voltage flag changes between LOW and
HIGHpress PROG+ key to enter other menu

(3)

HORIZON ADJUST(KEY 1 ):

a. Receive 50HZ monoscope PATTERN. Set TV to standard mode. Press KEY1 to enter
factory mode
b. Adjust 5HSH(for 60Hz picture,its is 6HSH)to set picture horizontal center to CRT
horizontal center.
c. Receive 60HZ monoscope PATTERN, repeat above b item
-14-

Service Adjustments
(4)VERTICAL&YUV/RGB HORIZON ADJUST(KEY2 ):
5VSL 50HZ vertical linearity
5VSH 50Hz vertical center
6VSL 60HZ vertical linearity
6VSH 60HZ vertical center

5SCL
5VAM
6SCL
6VAM

50Hz vertical slope correction

50Hz vertical size
60HZ vertical slope correction
60HZ vertical size

a. Receive 50Hz cross hatch signal, set TV to STANDARD mode, press digital key 2
after enter factory mode, adjust 5VSL so that pictures vertical line is just at the
bottom of the half picture.
b. Adjust 5VSH to set picture vertical center to CRT center.
c. Adjust 5SCL to set proper vertical linearity
d. Adjust 5VAM to obtain pictures vertical re-display ratio more than 90% .
e. If necessary, fine adjust above items.
f. Receive 50HZ RGB or YUV cross hatch signal,set TV to STANDARD mode,adjust
5RGH till picture horizontal center is at the CRT center.(OPTION)
g.
h. Receive 60Hz cross hatch signal, repeat above a,b.
f.Receive 60HZ RGB or YUV cross hatch signal,repeat above items.(OPTION)

(5)

OSD POSITION:
4-6-1 Menu OSD position adjustment: Receive 50/60HZ cross hatch pattern. Set
TV standard status. Press KEY 2 in factory mode, adjust 5VOF/6VOF and
HOF item, to obtain menu OSD at the center of CRT screen;
4-6-2 LOGO position adjustment: Receive 50/60HZ cross hatch pattern. Set TV
standard status. Press KEY 7 in factory mode, adjust XMIN,XMAX,YMIN,
and YMAX item, to obtain LOGO at the center upto 1/3 of CRT screen.
4-6-3 TELETEXT OSD position adjustment: Receive 50/60HZ TELETEXT signal.
Set TV standard status. Press KEY 7 in factory mode, adjust TXMI and
5TYM/6TYM item, to obtain INDEX at the center of CRT screen.

4-2

White Balance Adjustment (Applied in factory)KEY 3

Normally, this chassis can auto adjust white balance, but for some CRT need to adjust
white balance carefully by handSet BRIGHTNESS and CONTRAST at normal status ,
receive GREY SCAL and entering factory mode press KEY 3, set WPR at 31, adjust WPG
and WPR to obtain white balance.

4-3

RF.AGC ADJUSTMENT(KEY 4 )
4-3-1 Receive 60dB RF signal. Connect Digital voltmeter positive terminal to
tuner AGC terminal and negative terminal to GND.
4-3-2 Enter the AGC item in factory mode by the REMOTE CONTROL.
MethodPress key S.M.,

,
-15-

in turn to enter factory mode, then

Service Adjustments
press key 4 and select AGC item by PROG+/-.
4-3-3 Adjust VOL+ and VOL- keys to obtain 2.4V Digital voltage meter
reading or just no NOISE on screen
Press key

to exit factory mode

5E2PROM INITIALIZTION
(1)

E2PROM initialization (KEY 8 )

We can use an empty E2PROM when making the sample TV or repairing,also can use
the E2PROM which has been full of data,but you must follow the steps below to
initialize the E2PROM.
in turn to enter the factory modePress KEY

Press the keys CLOCK , P.M.,

8,VOL +/- in turn,you may see the OSDBUSY after theINITon the
screenAbout a while, the character
BUSYwill disappear
then POWER OFF
and ON the TV,the initialization is completed

(2)

FUNCTION SETTING (KEY 5 )

Press the keys CLOCK , P.M.,

in turn to enter the factory modePress KEY 5 to

enter the setting menu

b.Set values to OPTION 1- OPTION 7
c.LOGO setting when powered on or no signalPress key CLOCK in factory menu
to enter the LOGO edit modethere are two rowsthe 1st can set the
customers name etcand the 2nd row can set to display the customers
e-mail, phonePress the keys PROG +/- to select the character to
edituse keys VOL+/- to choose the charater.

The detailed instruction of 3P51

Some items displayed but not mentioned below is not used in 3P51 chassis.
.Item

Information of the factory menu

Storage

Display

address

string
RELEASE2.0;

Range (Index | value)

Default
value

Software Version

Fixed, not
changeable

Drect key 8

Initialization

initialize
uninitialize

INIT

Press key VOL +you can see the character INIT BUSY is
activeExit the menu and turn off the TV after the character

Instruction

disappearingreopen it can have a success to innitializeThen

the program has been storaged in the memorizerand then need
to readjust the parameter of the factory menu
-16-

Service Adjustments
.Item

Storage

Display

address

string

Range (Index | value)

Default
value

Drect key 0
Screen Voltage

A level bright line

Adjust the screen voltage under Tv standard mode and no signal

Instruction

inputjust can see the line is ok

Drect key 1
Horizontal paralellogram 50Hz

29

5PAR

0-63

31

Horizontal bow 50Hz

2A

5BOW

0-63

31

The above value be adjusted10 can be OK,the default value is31

Instruction
Horizontal shift 50Hz

2B

5HSH

0-63

19

EW width

2C

5EWW

0-63

33

EW parabola/width 50Hz

2D

5EWP

0-63

19

EW upper corner parabola 50Hz

2E

5UCR

0-63

33

EW lower corner parabola 50Hz

2F

5LCR

0-63

18

EW trapezium 50Hz

30

5EWT

0-63

43

Horizontal paralellogram 60Hz

37

6PAR

0-63

31

Horizontal bow 60Hz

38

6BOW

0-63

31

Horizontal shift 60Hz

39

6HSH

0-63

31

50Hz

The above value be adjusted10 can be OK,the default value is31

Instruction
EW width

60Hz

3A

6EWW

0-63

33

EW parabola/width 60Hz

3B

6EWP

0-63

19

EW upper corner parabola 60Hz

3C

6UCR

0-63

44

EW lower corner parabola 60Hz

3D

6LCR

0-63

10

EW trapezium

3E

6EWT

0-63

44

Vertical slope 50Hz

31

5VSL

0-63

31

Vertical amplitude 50Hz

32

5VAM

0-63

10

S-correction 50Hz

33

5SCL

0-63

31

60Hz

Drect key 2

Instruction

generally ,SCL can be setted to be31

Vertical shift 50Hz

34

5VSH

0-63

22

Horizontal shift 50Hz on RGB mode

35

5RGH

0-63

38

OSD vertical position offset 50Hz

36

5VOF

0-63

38

Horizontal shift on RGB mode generally between 30 to 42the

Instruction

direct way is to connect the two Tvs SCARTAdjust the Value

Vertical slope 60Hz

3F

6VSL

0-63

31

Vertical amplitude 60Hz

40

6VAM

0-63

11

S-correction 60Hz

41

6SCL

0-63

31

Vertical shift 60Hz

42

6VSH

0-63

23

Horizontal shift 60Hz on RGB mode

43

6RGH

0-63

38

OSD vertical position offset 60Hz

44

6VOF

0-63

31

OSD horizontal position offset

45

HOF

0-63

42

-17-

Service Adjustments
.Item

Storage

Display

address

string

Vertical zoom

46

Range (Index | value)

Default
value

VX

0-63

32

Adjust this item when lack of vertical amplitude will lead to the

Instruction

picture cant be full of the screen,then need to adjust the

resistances(R318,R319) value.

Direct Key 3
Black level off-set R

RED

0-63

32

Black level off-set G

GRN

0-63

32

White point R (Direct Key Red)

WPR

0-63

31

White point G (Direct KeGreen)

WPG

0-63

31

White point B (Direct Key Blue)

WPB

0-63

45

The white balance can be adjusted automatically on this

machineonly one or two tube need to be adjustedgenerally
the value of RED and GRN between 23 to 39,if adjust

Instruction

excessively will lead the picture fadedRemarkbecause of

the higher colour temperatureits normal that you feel a little
red

Luminance delay time PAL

YDFP

0-15

This item has the function to adjust the luminance and colour

Instruction

delay,change the NO. on P card,make the boundary of central

green and purple accord with the border of above gray pane.

Y delay time NTSC

YDFN

0-15

Y delay time SECAM

YDFS

0-15

Y delay time AV

YDAV

0-15

Teletext contrast

TTBR

0-15

15

MUTD

0-20

13

AGC take-over

AGC

0-63

27

UOC Volume

VOL

0-63

56

Mute

delay

time

while

program

switch

Instruction
Direct Key 4

Input standard RF signal with 1KHz sound ,measure UOC

Instruction

amplitude(location is W101) of output audio RMS value,adjust

VOL till it reaches to 0.5Vrms.

SUB HUE control

IF frequency
Cathode drive level

SHUE
IFFS
HDOL

-18-

0-63

35

38.9MHz

38.0MHz

0-15

2
2

Service Adjustments
.Item

Storage

Display

address

string

Range (Index | value)

Default
value

Adjust "HDOL" can change the voltage of R.G.Bobviously,but

adjust too high may lead to fade badly,reverse maybe lead to lack

Instruction

of luminance,so should be carefulGenerally it's ok when there is

no black screen or picture faded change the channel under the
maximal beam current

IF AGC speed

SPD

0.7X

Normal

3X

6X

VG2 Brightness

VG2B

0-63

31

TELETEXT brightness control

TRBI

0-63

25

Contrast Min pre-set

1CON

0-100

10

Brightness Min pre-set

1BRI

0-100

10

Colour Min pre-set

1COL

0-100

Sharpness Min pre-set

1SHP

0-100

Contrast Middle pre-set

2CON

0-100

60

Brightness Middle pre-set

2BRI

0-100

40

Colour Middle pre-set

2COL

0-100

45

Direct Key 6

Sharpness Middle pre-set

65

2SHP

0-100

60

Contrast Rich pre-set

66

3CON

0-100

100

Brightness Rich pre-set

67

3BRI

0-100

100

Colour Rich pre-set

68

3COL

0-100

100

Sharpness Rich pre-set

69

3SHP

0-100

100

Volume inflexion Pre-set

VL05

40

VL20

65

VL40

83

VL60

88

VL80

95

If VOL05 set to 40,it means when VOLUME is set to 05 by

user,the internal Volume is 40.This function is used to adjust

Instruction

speaker sound level-VOLUME OSD curve

opening time control

RGBL

0-25

Direct Key 7
Screen saver / Logo Left position

6A

XMIN

0-255

44

Screen saver Right position

6B

XMAX

0-255

186

Screen saver Top position

6C

YMIN

0-63

Screen saver Bottom position

6D

YMAX

0-63

37

Teletext Horizontal position

6E

TXMI

0-255

40

-19-

Service Adjustments
.Item

Storage

Display

Range (Index | value)

Default

address

string

Teletext Vertical position 50Hz

6F

5TYM

0-63

38

Teletext Vertical position 60Hz

70

6TYM

0-63

38

71

OP1

18

Bit 0

AVG

VSD

value

Instruction
Direct Key 5
NVM option 1
VG2 Alignment mode

VG2 is usually set to 0.Receive 49.75MHZ PHILIPS signal.

press key "PM" to set picture to standard mode, adjust FBT's
SCREEN VOLTAGE knob, if the screen voltage is too high, the

Instruction

OSD "high" appears, oppositely, OSD "low" appears, when you

see the characters "HIGH" and "LOW" display by turns, it means
VG2 is well set.

YUV or Yprpb

Bit 1

YUV

Yprpb

WIDE BAND SOUND PLL

Bit 2

off

on

BLACK STRETCH AMOUNT

Bit 3

10%

20%

AV2

Bit 4

off

on

SVHS

Bit 5

off

on

BLACK STRETCH DEPTH

Bit 6

20IRE

30IRE

XX

Bit 7

off

on

OP2

11

AVL

Bit 0

off

On

Auto sound in autosearch mode

Bit 1

off

On

Pan Europe Teletext set

Bit 2

Off

On

Cyrillic Teletext set

Bit 3

Off

On

NVM option 2

72

Farsi Teletext set

Bit 4

Off

On

Arabic Teletext set

Bit 5

Off

On

Sync On Y (YUV/Yprpb mode)

Bit 6

off

on

Slicing lever

Bit 7

Fixed

NVM option 3

73

dependent on
noise

OP3

255

Bit 0

Off

On

SW1

SW2

English Menu

English Menu

Farsi Menu

Farsi Menu

Bit 1

Off

On

Arabic Menu

Arabic Menu

Bit 2

Off

On

Turkey menu

Serbian Menu

Bit 3

Off

On

France Menu

Bulgaria Menu

Bit 4

Off

On

German menu

German menu

Bit 5

Off

On

Itality

Itality

Bit 6

Off

On

Bit 7

off

on

OP4

114

Narrow-band sound PLL window

Bit 0

small

large

Power mode

Bit 1

standby

Last Memory

Menu

Russia Menu

Menu

Russia Menu

NVM option 4

74

-20-

Service Adjustments
.Item

Storage

Display

address

string

Range (Index | value)

Default
value

Geometry control

Bit 2

off

On

Logo

Bit 3

off

On

EHT tracking mode

Bit 4

Vertical

Vert. & EW

Search tuing mode sensitivity

Bit 5

Normal

Reduced

Menu half-tone

Bit 6

Off

On

Zoom function

Bit 7

off

on

OP5

223

Sound system DK

Bit 0

Off

on

Sound system BG

Bit 1

Off

On

Sound system I

Bit 2

Off

On

CORING0

Bit 3

Off

On

CORING1

Bit 4

Off

On

AV3

Bit 5

off

On

Switch-off in vertical overscan

Bit 6

Undefined

Power on to last status

Bit 7

Off

On

OP6

218

No signal OSD when no signal

Bit 0

off

On

Blue screen or black screen

Bit 1

Black

Blue

16:9 mode

Bit 2

off

On

Child lock (Lock local key)

Bit 3

Off

On

Top & bottom bar on Menu

Bit 4

Off

On

Hotel mode

Bit 5

Off

On

No use

Set POC bit when no signal

Bit 6

Off

On

Game

Bit 7

off

on

NVM option 5

NVM option 6

75

76

Instruction
NVM option 7

Vert.
overscan

OP6 generally fixed to 218

77

AV1

OP7

196

Bit 0

off

on

Because of AV1 is back AVif SCART neededno back AV

Instruction

need to set AV1 0

XX

Bit 1

TV and monitor out select

Bit 2

Monitor

TV

Because the output of SCART always follow TVwhen back AV is

Instruction

SCARTthe value set to1

LISTEN PRESET

Bit 3

off

Power on always

Bit 4

Noise Reduce Off

Bit 5

Noise Reduce On

Bit 6

NTSC-M Control switch

Bit 7

1(FM)

0(QSS)

See OP4
bit 1

on

Direct On

See Table 1

0
1

TrueBass control

78

BASS

off

On

Comb-filter Control

79

COMB

Off

On

-21-

Service Adjustments
.Item

Storage

Display

Range (Index | value)

Default

address

string

NICAM control

7A

NICA

Off

On

RGB Control

7B

RGB

Off

On

YUV Control

7C

YUV

Off

On

NTSC-M Control

7D

off

on

value

Direct Key CLOCK

Logo edit (7 chars. & 2 lines)

Logo Text

English letter & number

etc

The LOGO edit function will take effect when Bit3 in OP4 set 1

Instruction

press key VOL+/- to choose characterand press PROG+/- to

choose ASC charater

Table 1 : Noise Reduce Setting for PAL

Noise Reduce On

Noise Reduce Off

OP7 Bit 5

OP5 Bit 6

2.7MHz

3.1MHz

2.7MHz

3.5MHz

3.1MHz

3.5MHz

3.1MHz

3.5MHz

* Remark : NTSC system preset to 2.7 -> 3.1MHz.

-22-