Scribd
Upload
242 views1 page

TDS 11001400 EN EN Zinc-Spray-bright-grade PDF

This technical datasheet provides information on Zinc Spray bright grade, including: 1) It should be applied to clean, degreased surfaces at room temperature from 25cm away, drying after 15 minutes and fully hardening after 10-12 hours. 2) It should be stored protected from sunlight at temperatures below 50°C. 3) It provides long-term cathodic corrosion protection when applied, forming a protective zinc flake layer that is resistant under weather conditions.

Uploaded by

KJ Supply
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
242 views1 page

TDS 11001400 EN EN Zinc-Spray-bright-grade PDF

This technical datasheet provides information on Zinc Spray bright grade, including: 1) It should be applied to clean, degreased surfaces at room temperature from 25cm away, drying after 15 minutes and fully hardening after 10-12 hours. 2) It should be stored protected from sunlight at temperatures below 50°C. 3) It provides long-term cathodic corrosion protection when applied, forming a protective zinc flake layer that is resistant under weather conditions.

Uploaded by

KJ Supply
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Technical Datasheet

Zinc Spray bright grade

Create Date: 06.06.2016 - Page 1/1

Pretreatment of the surface


Clean and degrease surfaces with WEICON Cleaner S.

Processing
Shake can before use until the mixing ball can be heard clearly. Spray
on evenly and crosswise at room temperature (approx. 20C) and at
about 25 cm distance from the surface. Dust-dry after approx. 15
minutes, fully hardened after approx. 10-12 hours.

Storage
Pressurized container: protect from sunlight and do not expose to
temperatures exceeding +50C.

Note
The specifications and recommendations given in this technical data
sheet must not be seen as guaranteed product characteristics. They
are based on our laboratory tests and on practical experience. Since
individual application conditions are beyond our knowledge, control and
responsibility, this information is provided without any obligation.

long-term cathodic corrosion protection


Zinc Spray bright grade is approved by the German TV and provides
a longlasting cathodic corrosion protection to all metal surfaces. It has
a bright colour shade matched to hot galvanization.
The spray forms a fast-drying, adherent protective layer of microfine
zinc flakes. The zinc flakes form a resistant protective layer, even
under extreme weather and environmental conditions.
Zinc Spray bright grade can be used for the coating of welded joints
and drilled holes, as a conductive intermediate layer for spot welding
and everywhere where metal must be protected against corrosion.
ISSA: 53.402.07
IMPA: 45 08 12

Technical data
Colour

RAL 9006, "Fresh hot-dip galvanisation"

Application

Indoors and outdoors

Binding agent

Modified Alkyd resin

Pigment

Flaky zinc and aluminium pigments

Pigment purity

about 99,9 Zn / approx. 99,5 Al

Percentage of metal in dry film

ca. 70 %

Content

400 ml

Specific weight

1,0 - 1,2 g/cm

Recommended primer
Processing temperature

Zinc Spray
+5 to +35, optimum temperature from +18 to + 25 C

Consumption at 1.5 cross coats

ca. 150 ml/m

Layer thickness at 1.5 cross coats

ca. 20-40 m

dust dry after

ca. 15 Min.

Hardened after

ca. 12 h

paintable

ca. 24 h

Abrasion-resistant
Cross cutting DIN 53151 / ISO 2409

abrasion-resistant
Cross cut characteristic value GT 0 to
GT 1

Salt spraying test ISO 9227


Mandrel bend test DIN EN ISO 1519
Top coating
Temperature resistance after complete hardening
Storage stability

>240 h
no hair cracking
not required
about -50 to +300 C
24 months

We do guarantee the continuously high quality of our products.


However, own adequate laboratory and practical tests to find out if the
product in question meets the requested properties are recommended.
A claim cannot be derived from them. The user bears the only
responsibility for non-appropriate or other than specified applications.

Health and Safety


When using WEICON products, the physical, safety technical,
toxicological and ecological data and regulations in our EC safety data
sheets (www.weicon.com) must be observed.

You might also like