LC320EXN
Product Specification
SPECIFICATION
FOR
APPROVAL
) Preliminary Specification
) Final Specification
Title
32.0 WXGA TFT LCD
BUYER
General
MODEL
SUPPLIER
LG Display Co., Ltd.
*MODEL
LC320EXN
SUFFIX
SCA1
*When you obtain standard approval,
please use the above model name without suffix
APPROVED BY
SIGNATURE
DATE
APPROVED BY
SIGNATURE
DATE
H.S.SONG / Team Leader
REVIEWED BY
/
Y.J.KIM / Project Leader
PREPARED BY
/
Please return 1 copy for your confirmation with
your signature and comments.
Ver. 1.1
Y.C.JANG / Engineer
TV Product Development Dept.
LG Display Co., Ltd
1 / 28
LC320EXN
Product Specification
CONTENTS
Number
ITEM
Page
COVER
CONTENTS
RECORD OF REVISIONS
GENERAL DESCRIPTION
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL SPECIFICATIONS
3-1
ELECTRICAL CHARACTERISTICS
3-2
INTERFACE CONNECTIONS
3-3
SIGNAL TIMING SPECIFICATIONS
10
3-4
LVDS SIGNAL SPECIFICATIONS
12
3-5
COLOR DATA REFERENCE
13
3-6
POWER SEQUENCE
14
OPTICAL SPECIFICATIONS
16
MECHANICAL CHARACTERISTICS
20
RELIABILITY
23
INTERNATIONAL STANDARDS
24
7-1
SAFETY
24
7-2
EMC
24
7-3
Environment
24
PACKING
25
8-1
DESIGNATION OF LOT MARK
25
8-2
PACKING FORM
25
PRECAUTIONS
26
9-1
MOUNTING PRECAUTIONS
26
9-2
OPERATING PRECAUTIONS
26
9-3
ELECTROSTATIC DISCHARGE CONTROL
27
9-4
PRECAUTIONS FOR STRONG LIGHT EXPOSURE
27
9-5
STORAGE
27
9-6
HANDLING PRECAUTIONS FOR PROTECTION FILM
27
Ver. 1.1
2 / 28
LC320EXN
Product Specification
RECORD OF REVISIONS
Revision No.
Revision Date
Page
0.0
Apr. 27, 2010
1.0
May. 27, 2010
25
-
1.1
Ver. 1.1
Aug. 19, 2010
22,23
Description
Preliminary Specification (First Draft)
Changed Safty standard
Final Specification
Update LCM Drawing
3 / 28
LC320EXN
Product Specification
1. General Description
The LC320EXN is a Color Active Matrix Liquid Crystal Display with an integral Light Emitting Diode(LED)
b a c k l i g ht s ys tem . T he m atr ix em p lo ys a- S i T hin F i lm T r ans is to r as the ac t i ve e lem ent.
It is a transmissive display type which is operating in the normally black mode. It has a 31.51 inch diagonally
measured active display area with WXGA resolution (768 vertical by 1366 horizontal pixel array).
Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in Horizontal stripes.
Gray scale or the luminance of the sub-pixel color is determined with a 8-bit gray scale signal for each dot,
thus presenting a palette of more than 16.7M(true) colors.
It has been designed to apply the 8-bit 1-port LVDS interface.
It is intended to support LCD TV, PCTV where high brightness, super wide viewing angle, high color gamut,
high color depth and fast response time are important.
RGB
EEPROM
SDA
SCL
+12.0V
LVDS 1Port
CN1
(30pin)
LVDS Select #9
Source Driver Circuit
S1
Timing Controller
[LVDS Rx + Spread Spectrum
Control
Integrated]
Signals
S1366
G1
TFT - LCD Panel
(1366
Power Circuit
Block
+24.0V, GND, On/off
Ext VBR-B
768 x RGB pixels)
[Gate In Panel]
G768
Power Signals
LED Driver
Back light Assembly(96 LED)
General Features
Active Screen Size
31.51 inches(800.4mm) diagonal
Outline Dimension
741.4 mm(H) x 435.8 mm(V) x 23.6 mm(D) (Typ.)
Pixel Pitch
510.75
Pixel Format
1366 horiz. by 768 vert. pixels RGB stripe arrangement
Color Depth
8bit, 16,7 M colors
Luminance, White
400 cd/m2 (Center 1 point) (Typ.)
Viewing Angle (CR>10)
Viewing angle free ( R/L 178(Min.), U/D 178(Min.))
Power Consumption
Total 45.44 Watt (Logic=4.2 W , LED Driver = 41.9W @ [ExtVbr_B=100%] )
Weight
5,900g(Typ.)
Display Operating Mode
Transmissive mode, normally black
Surface Treatment
Hard coating(3H), Anti-glare treatment of the front polarizer (Haze 10%)
Ver. 1.1
x 170.25
x RGB
4 / 28
LC320EXN
Product Specification
2. Absolute Maximum Ratings
The following items are maximum values which, if exceeded, may cause faulty operation or damage to the
LCD module.
Table 1. ABSOLUTE MAXIMUM RATINGS
Parameter
Value
Symbol
Unit
Min
Max
VLCD
-0.3
+14.0
VDC
VBL
-0.3
+ 27.0
VDC
ON/OFF
VOFF / VON
-0.3
+5.5
VDC
Brightness
EXTVBR-B
0.0
+5.5
VDC
VLOGIC
-0.3
+4.0
VDC
Operating Temperature
TOP
+50
Storage Temperature
TST
-20
+60
Panel Front Temperature
TSUR
+68
Operating Ambient Humidity
HOP
10
90
%RH
Storage Humidity
HST
10
90
%RH
LCD Circuit
Power Input Voltage
Driver
Driver Control Voltage
T-Con Option Selection Voltage
Note
2,3
4
2,3
Note 1. Ambient temperature condition (Ta = 25 2 C )
2. Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be Max 39 C, and no condensation of water.
3. Gravity mura can be guaranteed below 40 C condition.
4. The maximum operating temperatures is based on the test condition that the surface temperature
of display area is less than or equal to 68 C with LCD module alone in a temperature controlled chamber.
Thermal management should be considered in final product design to prevent the surface temperature of
display area from being over 68 . The range of operating temperature may degraded in case of
improper thermal management in final product design.
90%
60
60%
50
C]
Humidity [(%)RH]
Wet Bulb
Temperature [
40
40%
30
20
Storage
Operation
10
0
-20
10%
10
20
30
40
Dry Bulb Temperature [
Ver. 1.1
50
60
70
80
C]
5 / 28
LC320EXN
Product Specification
3. Electrical Specifications
3-1. Electrical Characteristics
It requires two power inputs. One is employed to power for the LCD circuit. The other Is used for the LED
backlight and LED Driver circuit.
Table 2. ELECTRICAL CHARACTERISTICS
Parameter
Symbol
Value
Unit
Note
Min
Typ
Max
10.8
12.0
13.2
VDC
347
450
mA
495
643
mA
Circuit :
Power Input Voltage
VLCD
Power Input Current
ILCD
Power Consumption
PLCD
4.2
5.85
Watt
Rush current
IRUSH
3.0
Notes : 1. The specified current and power consumption are under the VLCD=12.0V, 25 2 C, fV=60Hz
condition whereas mosaic pattern(8 x 6) is displayed and fV is the frame frequency.
2. The current is specified at maximum current pattern.
3. The duration of rush current is about 2ms and rising time of power input is 0.5ms (min.).
White : 255 Gray
Black : 0 Gray
Mosaic Pattern(8 x 6)
Ver. 1.1
6 / 28
LC320EXN
Product Specification
Table 3. ELECTRICAL CHARACTERISTICS (Continue)
Parameter
Symbol
Values
Unit
Notes
25.2
Vdc
1.7
1.8
2.5
PBL
41.9
44.5
On
V on
2.5
5.0
Vdc
Off
V off
-0.3
0.0
0.7
Vdc
ExtVBR-B
100
Min
Typ
Max
VBL
22.8
24.0
Power Supply Input Current
IBL_A
Power Supply Input Current (In-Rush)
Irush
Power Consumption
LED Driver :
Power Supply Input Voltage
On/Off
Brightness Adjust
Input Voltage for
Control System PWM Frequency for
Signals
NTSC & PAL
Pulse Duty Level
(PWM)
VBL = 22.8V
Ext VBR-B = 100%
1
On Duty
PAL
100
Hz
NTSC
120
Hz
4
HIGH : on duty
LOW : off duty
High Level
2.5
5.0
Vdc
Low Level
0.0
0.7
Vdc
LED :
Life Time
30,000
Hrs
Notes :
1. Electrical characteristics are determined after the unit has been ON and stable for approximately 60
minutes at 25 2 C. The specified current and power consumption are under the typical supply Input voltage
24Vand VBR (ExtVBR-B : 100%), it is total power consumption.
2. The life time(MTTF) is determined as the time which luminance of the LED is 50% compared to that of initial
value at the typical LED current (ExtVBR-B :100%) on condition of continuous operating in LCM state at
25 2 C.
3. LGD recommend that the PWM freq. is synchronized with One time harmonic of Vsync signal of system.
Though PWM frequency is over 120Hz (max 252Hz), function of LED Driver is not affected.
4. The duration of rush current is about 200ms.
5. Even though inrush current is over the specified value, there is no problem if I2T spec of fuse is satisfied.
Ver. 1.1
7 / 28
LC320EXN
Product Specification
3-2. Interface Connections
This LCD module employs two kinds of interface connection, a 30-pin connector is used for the module
electronics and 14-pin connector is used for the integral backlight system.
3-2-1. LCD Module
- LCD Connector(CN1) : KDF71G-30S-1H(Hirose) or FI-X30SSL-HF(JAE)
- Mating Connector : : FI-X30C2L (Manufactured by JAE) or Equivalent
Table 4. MODULE CONNECTOR(CN1) PIN CONFIGURATION
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Symbol
VLCD
VLCD
VLCD
VLCD
GND
GND
GND
GND
LVDS Select
GND
Description
Power Supply +12.0V
Power Supply +12.0V
Power Supply +12.0V
Power Supply +12.0V
Ground
Ground
Ground
Ground
H =JEIDA , L or NC = VESA
Ground
GND
RARA+
GND
RBRB+
GND
RCRC+
GND
RCLKRCLK+
GND
RDRD+
GND
PWM OUT
Ground
LVDS Receiver Signal(-)
LVDS Receiver Signal(+)
Ground
LVDS Receiver Signal(-)
LVDS Receiver Signal(+)
Ground
LVDS Receiver Signal(-)
LVDS Receiver Signal(+)
Ground
LVDS Receiver Clock Signal(-)
LVDS Receiver Clock Signal(+)
Ground
LVDS Receiver Signal(-)
LVDS Receiver Signal(+)
Ground
PWM output (From LCM)
28
Ext VBR-B
External VBR (From System)
29
30
NC
GND
Note
Appendix III
No Connection
Ground
Notes : 1. All GND (Ground) pins should be connected together to the LCD modules metal frame.
2. All VLCD (power input) pins should be connected together.
3. All Input levels of LVDS signals are based on the EIA 644 Standard.
Ver. 1.1
8 / 28
LC320EXN
Product Specification
3-2-2. Backlight Module
Master
- LED Driver Connector : 20022WR-14B1(Yeonho) or Equivalent
- Mating Connector : 20022HS-14 or Equivalent
Table 5. LED DRIVER CONNECTOR PIN CONFIGURATION
Pin No
Symbol
Description
VBL
Power Supply +24.0V
VBL
Power Supply +24.0V
VBL
Power Supply +24.0V
VBL
Power Supply +24.0V
VBL
Power Supply +24.0V
GND
Backlight Ground
GND
Backlight Ground
GND
Backlight Ground
GND
Backlight Ground
10
GND
Backlight Ground
11
NC
12
VON/OFF
13
EXTVBR-B
14
Status
Note
No Connection
Backlight ON/OFF control
External PWM
LED Status
Notes :
1. GND should be connected to the LCD modules metal frame.
2. High : on duty / Low : off duty, Pin#13 can be opened. ( if Pin #13 is open , EXTVBR-B is 100% )
3. Normal : Low (under 0.7V) / Abnormal : High (upper 3.0V)
4. Each impedance of 12 and 13 is over 50[K ] and over 50[K ].
Rear view of LCM
PCB
14
Ver. 1.1
9 / 28
LC320EXN
Product Specification
3-3. Signal Timing Specifications
Table 6 shows the signal timing required at the input of the LVDS transmitter. All of the interface signal
timings should be satisfied with the following specification for normal operation.
Table 6. TIMING TABLE for NTSC &PAL
ITEM
Symbol
[ DE (Data Enable) Only ]
Min
Typ
tCLK
12.5
13.8
15.8
ns
63
72.4
80
MHz
Period
tHP
1456
1528
1920
tCLK
Horizontal Valid
tHV
1366
1366
1366
tCLK
Horizontal Blank
tHB
90
162
554
tCLK
Frequency
fH
45
47.4
50
KHz
Width
tWH
26
32
48
tCLK
Horizontal Back Porch
tHBP
24
48
tCLK
Horizontal Front Porch
tHFP
40
80
tCLK
Period
tVP
776
(894)
790
(948)
1008
(1063)
tHP
Vertical Valid
tVV
768
768
768
tHP
Vertical Blank
tVB
Frequency
fV
8
(126)
57
(47)
22
(180)
60
(50)
240
(295)
63
(53)
10
tHP
5
(92)
1
(32)
15
(135)
2
(40)
tHP
tHP
Period
Max
Unit
Note
DCLK
Frequency
Hsync
Vsync
Width
tWV
Vertical Back Porch
tVBP
Vertical Front Porch
tVFP
tHP
Hz
1
NTSC : 57~63Hz
(PAL : 47~53Hz)
Note 1. tHB = tHFP + tWH +tHBP
tVB = tVFP + tWV +tVBP
The Input of HSYNC & VSYNC signal does not have an effect on normal operation(DE Only Mode).
The performance of the electro-optical characteristics may be influenced by variance of the vertical
refresh rate.
Ver. 1.1
10 / 28
LC320EXN
Product Specification
3-4. Signal Timing Waveforms
3-4-1. LVDS Input Signal Timing Diagram
DE, Data
0.7VDD
0.3VDD
tCLK
0.5 VDD
DCLK
Valid data
First data
Invalid data
Pixel 0,0
Pixel 2,0
Invalid data
DE(Data Enable)
tHV
tHP
1
768
DE(Data Enable)
tVV
tVP
Ver. 1.1
11 / 28
LC320EXN
Product Specification
3-4-2. LVDS Input Signal Characteristics
1) DC Specification
LVDS
LVDS
V CM
V IN _ MAX
V IN _ MIN
# V CM = {( LVDS +) + ( LVDS - )} /2
0V
Description
Symbol
Min
Max
Unit
Note
LVDS Common mode Voltage
VCM
1.0
1.5
LVDS Input Voltage Range
VIN
0.7
1.8
Change in common mode Voltage
VCM
250
mV
2) AC Specification
Tclk
LVDS Clock
A
LVDS Data
tSKEW tSKEW
( F clk = 1/T clk )
A
Tclk
LVDS 1st Clock
80%
LVDS 2nd / 3rd / 4th Clock
20%
tRF
tSKEW_min tSKEW_max
Description
LVDS Differential Voltage
Symbol
High Threshold
Low Threshold
LVDS Clock to Data Skew Margin
Max
Unit
Note
VTH
100
300
mV
VTL
-300
-100
mV
|(0.25*Tclk)/7|
ps
(0.3*Tclk)/7
ps
ps
Tclk
tSKEW
LVDS Clock/DATA Rising/Falling time
tRF
Effective time of LVDS
teff
LVDS Clock to Clock Skew Margin (Even to Odd)
Min
tSKEW_EO
260
360
1/7* Tclk
Note 1. All Input levels of LVDS signals are based on the EIA 644 Standard.
2. If tRF isnt enough, teff should be meet the range.
3. LVDS Differential Voltage is defined within teff
Ver. 1.1
12 / 28
LC320EXN
Product Specification
360ps
V+
data
tui
0.5tui
VTH
Vcm
VTL
Vdata
360ps
teff
V+
clk
tui : Unit Interval
Vcm
Vclk
Ver. 1.1
13 / 28
LC320EXN
Product Specification
3-5. Color Data Reference
The brightness of each primary color (Red, Green, Blue) is based on the 8-bit gray scale data input for the color.
The higher binary input, the brighter the color. Table 7 provides a reference for color versus data input.
Table 7. COLOR DATA REFERENCE
Input Color Data
RED
Color
GREEN
MSB
BLUE
LSB MSB
LSB MSB
LSB
R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0
Basic
Color
Black
0 0
0 0
Red (255)
1 0
0 0
Green (255)
0 1
1 0
Blue (255)
0 0
0 1
Cyan
0 1
1 1
Magenta
1 0
0 1
Yellow
1 1
1 0
White
1 1
1 1
RED (000)
Dark 0
0 0
0 0
RED (001)
1 0
0 0
RED
...
...
...
...
RED (254)
0 0
0 0
RED (255)
1 0
0 0
GREEN (000) Dark 0
0 0
0 0
GREEN (001)
0 0
1 0
...
GREEN
...
...
...
GREEN (254)
0 1
0 0
GREEN (255)
0 1
1 0
BLUE (000)
Dark 0
0 0
0 0
BLUE (001)
0 0
0 0
BLUE
...
...
...
...
BLUE (254)
0 0
0 1
BLUE (255)
0 0
0 1
Ver. 1.1
14 / 28
LC320EXN
Product Specification
3-6. Power Sequence
3-6-1. LCD Driving circuit
90%
Power Supply For LCD
VLCD
0V
90%
10%
10%
T1
T8
T2
Interface Signal (Tx)
Valid Data
10%
T5
Vcm : LVDS Common mode Voltage
30%
0V
100%
T3
T4
T6
User Control Signal
(LVDS_select)
T7
Power for LED
LED ON
Table 8. POWER SEQUENCE
Value
Parameter
Unit
Notes
Min
Typ
Max
0.5
20
ms
T2
ms
T3
200
ms
T4
200
ms
T5
1.0
T6
T2
ms
T7
0.5
T8
100
ms
T1
Note : 1. Please avoid floating state of interface signal at invalid period.
2. When the power supply for LCD (VLCD) is off, be sure to pull down the valid and invalid data to 0V.
3. The T3 / T4 is recommended value, the case when failed to meet a minimum specification,
abnormal display would be shown. There is no reliability problem.
4. If the on time of signals(Interface signal and user control signals) precedes the on time of Power(VLCD),
it will be happened abnormal display. When T6 is NC status, T6 doesnt need to be measured.
5. T5 should be measured after the Module has been fully discharged between power off and on
period.
6. It is recommendation specification that T8 has to be 100ms as a minimum value.
Ver. 1.1
15 / 28
LC320EXN
Product Specification
3-6-2. Sequence for LED Driver
Power Supply For LED Driver
24V (typ.)
90%
VBL
0.7V
10%
0V
T1
T3
T2
VON/OFF
LED BL ON
Ext-VBR-B
T4
T5
3-6-3. Dip condition for LED driver
T6
VBL : 24V
VBL(Typ.) x 0.8
0V
Table 9. Power Sequence for LED Driver
Parameter
Values
Min
Typ
Max
Units
Remarks
1
T1
20
ms
T2
500
ms
T3
10
T4
T5
ms
T6
10
ms
ms
ms
VBL(Typ) x 0.8
Notes : 1. T1 describes rising time of 0V to 24V and this parameter does not applied at restarting time.
Even though T1 is over the specified value, there is no problem if I2T spec of fuse is satisfied.
Ver. 1.1
16 / 28
LC320EXN
Product Specification
4. Optical Specification
Optical characteristics are determined after the unit has been ON and stable in a dark environment at 25 2 C.
The values are specified at an approximate distance 50cm from the LCD surface at a viewing angle of and
equal to 0 .
FIG. 1 shows additional information concerning the measurement equipment and method.
Optical Stage(x,y)
LCD Module
Pritchard 880 or
equivalent
50cm
FIG. 1 Optical Characteristic Measurement Equipment and Method
Ta= 25 2 C, VLCD=12.0V, fV=60Hz, Dclk=72.4MHz,
EXTVBR_B=100%
Table 10. OPTICAL CHARACTERISTICS
Parameter
Contrast Ratio
CR
Surface Luminance, white
LWH
WHITE
Luminance Variation
Response Time
Symbol
Gray-to-Gray
(BW)
Variation
RED
GREEN
Color Coordinates
[CIE1931]
BLUE
WHITE
5P
G to G BW
Value
Min
Typ
Max
800
1200
1
cd/m2
400
1.3
13
ms
ms
degree
Rx
0.639
Ry
0.340
Gx
0.322
Bx
Note
320
G to G
Gy
Unit
Typ
-0.03
0.600
0.152
By
0.055
Wx
0.279
Wy
0.292
2
3
Typ
+0.03
Viewing Angle (CR>10)
Gray Scale
Ver. 1.1
x axis, right(=0 )
89
x axis, left (=180 )
89
y axis, up (=90 )
89
y axis, down (=270 )
89
17 / 28
LC320EXN
Product Specification
Notes : 1. Contrast Ratio (CR) is defined mathematically as :
Surface Luminance at all white pixels
CR =
Surface Luminance at all black pixels
It is measured at center 1-point.
2. Surface luminance is determined after the unit has been ON and 1Hour after lighting the
backlight in a dark environment at 25 2 C. Surface luminance is the luminance value at center
1-point across the LCD surface 50cm from the surface with all pixels displaying white.
For more information see the FIG. 2.
3. The variation in surface luminance , WHITE is defined as :
WHITE(5P) = Maximum(Lon1,Lon2, Lon3, Lon4, Lon5) / Minimum(Lon1,Lon2, Lon3, Lon4, Lon5)
Where Lon1 to Lon5 are the luminance with all pixels displaying white at 5 locations .
For more information, see the FIG. 2.
4. Response time is the time required for the display to transit from G(N) to G(M) (Rise Time, TrR)
and from G(M) to G(N) (Decay Time, TrD). For additional information see the FIG. 3. (N<M)
G to G Spec stands for average value of all measured points.
Photo Detector : RD-80S / Field : 2
5. Gray to Gray Response time uniformity is Reference data. Please see Appendix XI.
6. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are
determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which
is normal to the LCD module surface. For more information, see the FIG. 4.
7. Gray scale specification
Gamma Value is approximately 2.2. For more information, see the Table 11.
Table 11. GRAY SCALE SPECIFICATION
Ver. 1.1
Gray Level
L0
Luminance [%] (Typ.)
0.08
L15
0.27
L31
1.04
L47
2.49
L63
4.68
L79
7.66
L95
11.5
L111
16.1
L127
21.6
L143
28.1
L159
35.4
L175
43.7
L191
53.0
L207
63.2
L223
74.5
L239
86.7
L255
100
18 / 28
LC320EXN
Product Specification
Measuring point for surface luminance & measuring point for luminance variation.
A : H / 4 mm
B : V / 4 mm
@ H,V : Active Area
FIG. 2 5 Points for Luminance Measure
Response time is defined as the following figure and shall be measured by switching the input signal for
Gray(N) and Gray(M).
T rR
TrD
100
90
Optical
Response
10
0
Gray(N)
Gray(M)
Gray(N)
N,M = 0(Black)~255(White), N<M
FIG. 3 Response Time
Ver. 1.1
19 / 28
LC320EXN
Product Specification
Dimension of viewing angle range
Normal
= 180 , Left
= 90 , Up
= 0 , Right
= 270 , Down
FIG. 4 Viewing Angle
Ver. 1.1
20 / 28
LC320EXN
Product Specification
5. Mechanical Characteristics
Table 12 provides general mechanical characteristics.
Table 12. MECHANICAL CHARACTERISTICS
Item
Outline Dimension
Bezel Area
Active Display Area
Weight
Value
Horizontal
741.4mm
Vertical
435.8 mm
Depth
23.6 mm
Horizontal
705.4mm
Vertical
399.8mm
Horizontal
697.685mm
Vertical
392.256mm
5,900 g (Typ.), 6,200 g (Max.)
Note : 1.Please refer to a mechanical drawing in terms of tolerance at the next page.
Ver. 1.1
21 / 28
LC320EXN
Product Specification
<FRONT VIEW>
Ver. 1.1
22 / 28
LC320EXN
Product Specification
<REAR VIEW>
Ver. 1.1
23 / 28
LC320EXN
Product Specification
6. Reliability
Table 13. ENVIRONMENT TEST CONDITION
No.
Test Item
Condition
High temperature storage test
Ta= 60 C, 240h
Low temperature storage test
Ta= -20 C 240h
High temperature operation test
Ta= 50 C 50%RH
Low temperature operation test
Ta= 0 C
Vibration test
(non-operating)
Wave form : random
Vibration level : 1.0Grms
Bandwidth : 10-300Hz
Duration : X,Y,Z, 30 min
Each direction per 10 min
Shock test
(non-operating)
Shock level : 100Grms
Waveform : half sine wave, 2ms
Direction : X, Y, Z
One time each direction
Humidity condition Operation
Ta= 40 C ,90%RH
Altitude operating
storage / shipment
0 - 15,000 ft
0 - 40,000 ft
240h
240h
Note : Before and after Reliability test, LCM should be operated with normal function.
Ver. 1.1
24 / 28
LC320EXN
Product Specification
7. International Standards
7-1. Safety
a) UL 60065, Seventh Edition, Underwriters Laboratories Inc.
Audio, Video and Similar Electronic Apparatus - Safety Requirements.
b) CAN/CSA C22.2 No.60065:03, Canadian Standards Association.
Audio, Video and Similar Electronic Apparatus - Safety Requirements.
c) EN 60065:2002 + A11:2008, European Committee for Electrotechnical Standardization (CENELEC).
Audio, Video and Similar Electronic Apparatus - Safety Requirements.
d) IEC 60065:2005 + A1:2005, The International Electrotechnical Commission (IEC).
Audio, Video and Similar Electronic Apparatus - Safety Requirements.
(Including report of IEC60825-1:2001 clause 8 and clause 9)
Notes
1. Laser (LED Backlight) Information (SEOUL SEMICONDUCTOR, EWT719P)
Class 1M LED Product
IEC60825-1 : 2001
Embedded LED Power (Class1M)
Power : 6.4145 mW (Max.)
Wavelength : 447, 277 ~526 (nm)
Width : 1.2 x 0.55 (mm)
2. Caution
: LED inside.
Class 1M laser (LEDs) radiation when open.
Do not open while operating.
7-2. EMC
a) ANSI C63.4 American National Standard for Methods of Measurement of Radio-Noise
Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz.
American National Standards Institute (ANSI), 2003.
b) CISPR 22 Information technology equipment Radio disturbance characteristics Limit and
methods of measurement." International Special Committee on Radio Interference
(CISPR), 2005.
c) CISPR 13 Sound and television broadcast receivers and associated equipment Radio disturbance
characteristics Limits and method of measurement." International Special Committee on Radio
Interference (CISPR), 2006.
7-3. Environment
a) RoHS, Directive 2002/95/EC of the European Parliament and of the council of 27 January 2003
Ver. 1.1
25 / 28
LC320EXN
Product Specification
8. Packing
8-1. Information of LCM Label
a) Lot Mark
A
A,B,C : SIZE(INCH)
E : MONTH
D : YEAR
F ~ M : SERIAL NO.
Note
1. YEAR
Year
2001
2002
2003
2004
2005
2006
2007
2008
2009
2010
Mark
Month
Jan
Feb
Mar
Apr
May
Jun
Jul
Aug
Sep
Oct
Nov
Dec
Mark
2. MONTH
b) Location of Lot Mark
Serial No. is printed on the label. The label is attached to the backside of the LCD module.
This is subject to change without prior notice.
8-2. Packing Form
a) Package quantity in one box : 6 pcs
b) Box size : 840 mm(W) X 365 mm(D) X 530 mm(H)
Ver. 1.1
26 / 28
LC320EXN
Product Specification
9. Precautions
Please pay attention to the followings when you use this TFT LCD module.
9-1. Mounting Precautions
(1)You must mount a module using specified mounting holes (Details refer to the drawings).
(2) You should consider the mounting structure so that uneven force (ex. Twisted stress) is not applied to the
module. And the case on which a module is mounted should have sufficient strength so that external
force is not transmitted directly to the module.
(3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer.
Transparent protective plate should have sufficient strength in order to the resist external force.
(4) You should adopt radiation structure to satisfy the temperature specification.
(5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former
generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break
by electro-chemical reaction.
(6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than HB
pencil lead. And please do not rub with dust clothes with chemical treatment.
Do not touch the surface of polarizer for bare hand or greasy cloth.(Some cosmetics are detrimental
to the polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like
chamois soaks with petroleum benzine. Normal-hexane is recommended for cleaning the adhesives
used to attach front / rear polarizers. Do not use acetone, toluene and alcohol because they cause
chemical damage to the polarizer. * There is no problem of Panel crack under 5kgf / 10mm
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes
deformations and color fading.
(9) Do not open the case because inside circuits do not have sufficient strength.
9-2. Operating Precautions
(1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage :
V= 200mV(Over and under shoot voltage)
(2) Response time depends on the temperature.(In lower temperature, it becomes longer.)
(3) Brightness depends on the temperature. (In lower temperature, it becomes lower.)
And in lower temperature, response time(required time that brightness is stable after turned on) becomes
longer.
(4) Be careful for condensation at sudden temperature change. Condensation makes damage to polarizer or
electrical contacted parts. And after fading condensation, smear or spot will occur.
(5) When fixed patterns are displayed for a long time, remnant image is likely to occur.
(6) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be
done by system manufacturers. Grounding and shielding methods may be important to minimized the
interference.
(7) Please do not give any mechanical and/or acoustical impact to LCM. Otherwise, LCM cant be operated
its full characteristics perfectly.
(8) A screw which is fastened up the steels should be a machine screw.
(if not, it causes metallic foreign material and deal LCM a fatal blow)
(9) Please do not set LCD on its edge.
(10) The conductive material and signal cables are kept away from LED driver inductor to prevent abnormal
display, sound noise and temperature rising.
Ver. 1.1
27 / 28
LC320EXN
Product Specification
9-3. Electrostatic Discharge Control
Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that
treatment persons are connected to ground through wrist band etc. And dont touch interface pin directly.
9-4. Precautions for Strong Light Exposure
Strong light exposure causes degradation of polarizer and color filter.
9-5. Storage
When storing modules as spares for a long time, the following precautions are necessary.
(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature
between 5 C and 35 C at normal humidity.
(2) The polarizer surface should not come in contact with any other object.
It is recommended that they be stored in the container in which they were shipped.
9-6. Handling Precautions for Protection Film
(1) The protection film is attached to the bezel with a small masking tape.
When the protection film is peeled off, static electricity is generated between the film and polarizer.
This should be peeled off slowly and carefully by people who are electrically grounded and with well ionblown equipment or in such a condition, etc.
(2) When the module with protection film attached is stored for a long time, sometimes there remains a very
small amount of glue still on the bezel after the protection film is peeled off.
(3) You can remove the glue easily. When the glue remains on the bezel surface or its vestige is recognized,
please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normalhexane.
Ver. 1.1
28 / 28
LC320EXN
Product Specification
# APPENDIX- I
Package
Palletizing Size : 1140 X 870 X 1180.5
Box Quantity : 6 ea
NO.
DESCRIPTION
LCD Module
BAG
MATERIAL
NO.
DESCRIPTION
PACKING ASSY
AL
10
PALLET
Plywood
TAPE
MASKING 20MMX50M
11
ANGLE, COVER
PAPER(SW)
Packing
EPS
12
LABEL
ART 100X70
Packing
EPS
13
BAND
PP
BOX
PAPER(DW)
14
CLIP, BAND
STEEL
TAPE
OPP 70MMX300M
15
Wrap
LLDPE
Label
ART 100X70
Ver. 1.1
MATERIAL
29 / 28
LC320EXN
Product Specification
# APPENDIX- II-1
LCM Label
Model
LC320EXN
(SC)(A1)
RoHS Verified
Serial No.
UL, TUV Mark
************* ***
LGD Logo
LIGHT GUIDE : >PMMA<
US PATENT No.
Ver. 1.1
MADE IN KOREA
Origin
30 / 28
LC320EXN
Product Specification
# APPENDIX- II-2
Box Label
6 pcs
Ver. 1.1
Pallet Label
LC320EXN
LC320EXN
SCA1
SCA1
36 pcs
31 / 28
LC320EXN
Product Specification
# APPENDIX-III-1
Required signal assignment for Flat Link Transmitter(Pin9=L or NC)
Host System
24 Bit
48
TxOUT047
TxOUT0+
12
13
100
RxIN0RxIN0+
46
TxOUT145
TxOUT1+
15
16
100
RxIN1RxIN1+
42
TxOUT241
TxOUT2+
18
19
100
RxIN2RxIN2+
40
TxCLKOUT39
TxCLKOUT+
21
22
100
RxCLKINRxCLKIN+
38
TxOUT337
TxOUT3+
24
25
100
RxIN3RxIN3+
9
30
GND
51
52
54
55
56
3
50
2
4
6
7
11
12
14
8
10
15
19
20
22
23
24
16
18
27
28
30
31
Timing
Controller
KDF71G-30S-1H
GND
RED0
RED1
RED2
RED3
RED4
RED5
RED6
RED7
GREEN0
GREEN1
GREEN2
GREEN3
GREEN4
GREEN5
GREEN6
GREEN7
BLUE0
BLUE1
BLUE2
BLUE3
BLUE4
BLUE5
BLUE6
BLUE7
Hsync
Vsync
Data Enable
CLOCK
DS90C385
or Compatible
VESA / JEIDA
LCD Test
LCD Module
Notes:
1. The LCD module uses a 100 Ohm( ) resistor between positive and negative lines
of each receiver input.
2. Refer to LVDS transmitter data sheet for detail descriptions. (DS90C385 or Compatible)
3. 7 means MSB and 0 means LSB at R,G,B pixel data.
Ver. 1.1
32 / 28
LC320EXN
Product Specification
# APPENDIX-III-1
Required signal assignment for Flat Link Transmitter(Pin9=H)
Host System
24 Bit
48
TxOUT047
TxOUT0+
12
13
100
RxIN0RxIN0+
46
TxOUT145
TxOUT1+
15
16
100
RxIN1RxIN1+
42
TxOUT241
TxOUT2+
18
19
100
RxIN2RxIN2+
40
TxCLKOUT39
TxCLKOUT+
21
22
100
RxCLKINRxCLKIN+
38
TxOUT337
TxOUT3+
24
25
100
RxIN3RxIN3+
9
30
GND
50
2
51
52
54
55
56
3
8
10
4
6
7
11
12
14
16
18
15
19
20
22
23
24
27
28
30
31
Timing
Controller
KDF71G-30S-1H
Vcc
RED0
RED1
RED2
RED3
RED4
RED5
RED6
RED7
GREEN0
GREEN1
GREEN2
GREEN3
GREEN4
GREEN5
GREEN6
GREEN7
BLUE0
BLUE1
BLUE2
BLUE3
BLUE4
BLUE5
BLUE6
BLUE7
Hsync
Vsync
Data Enable
CLOCK
DS90C385
or Compatible
VESA / JEIDA
LCD Test
LCD Module
Notes:
1. The LCD module uses a 100 Ohm( ) resistor between positive and negative lines
of each receiver input.
2. Refer to LVDS transmitter data sheet for detail descriptions. (DS90C385 or Compatible)
3. 7 means MSB and 0 means LSB at R,G,B pixel data.
Ver. 1.1
33 / 28
LC320EXN
Product Specification
# APPENDIX- III-2
LVDS Data-Mapping info. (8bit)
LVDS Select : H Data-Mapping (JEIDA format)
RCLKP
RCLKM
RAP
R13
R12
G12
R17
R16
R15
R14
R13
R12
G12
RBP
G14
G13
B13
B12
G17
G16
G15
G14
G13
B13
RCP
B15
B14
DE
VSYNC HSYNC B17
B16
B15
B14
DE
RDP
R11
R10
G10
R11
R10
B11
B10
G11
LVDS Select : L Data-Mapping (VESA format)
RCLKP
RCLKM
Ver. 1.1
RAP
R11
R10
G10
R15
R14
R13
R12
R11
R10
G10
RBP
G12
G11
B11
B10
G15
G14
G13
G12
G11
B15
RCP
B13
B12
DE
VSYNC HSYNC B15
B14
B13
B12
DE
RDP
R17
R16
G16
R17
R16
B17
B16
G17
34 / 28
LC320EXN
Product Specification
# APPENDIX- III-3
Option Pin Circuit Block Diagram
1) Circuit Block Diagram of LVDS Format Selection pin
Selector (Pin 9)
Selector
1K
50K
ASIC
(TCON)
System Side
Ver. 1.1
LCM Side
35 / 28
LC320EXN
Product Specification
# APPENDIX- IV
Humming Noise Level
These are measurement method and condition of Humming Noise Level for LC320EXN-SCA1 model of
RV sample conditions
Type of room
Anechoic
Distance to display
0.5m (Typical)
Measurement Point
@ LCM Center
Humming Noise Level
Ver. 1.1
Front
Typ 19dBA, Max 20dBA
Rear
Max 25dBA
36 / 28
