Scribd
Upload
458 views2 pages

TGN 11 Clip Spacing 09-12

The document discusses recommended spacing for rail clips used to mount crane rails. It notes that while closely spaced clips provide more safety, wider spacing is more cost effective if still safe. The technical section explains that horizontal bending moments vary between rail types so clip spacing cannot be calculated solely on that basis. The suggested spacing section then recommends 600-650mm for normal applications, 500mm for heavy duty, and 800mm for light duty. Other considerations like crane wheel base divisions and reinforcement cage spacing are also discussed.

Uploaded by

kayakeras3335
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
458 views2 pages

TGN 11 Clip Spacing 09-12

The document discusses recommended spacing for rail clips used to mount crane rails. It notes that while closely spaced clips provide more safety, wider spacing is more cost effective if still safe. The technical section explains that horizontal bending moments vary between rail types so clip spacing cannot be calculated solely on that basis. The suggested spacing section then recommends 600-650mm for normal applications, 500mm for heavy duty, and 800mm for light duty. Other considerations like crane wheel base divisions and reinforcement cage spacing are also discussed.

Uploaded by

kayakeras3335
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Clip spacing for Gantrail crane

rail clips
www.gantrail.com

Every application of Gantrail clips requires the selection of a suitable clip spacing.
Unfortunately there is no simple means of calculating a value. Thus one must rely
on practical experience. Closely spaced clips result in a design that has a high
factor of safety. However, a competitive solution uses clips at the widest sensible
spacing consistent with safety. This note gives recommended spacing.

TECHNICAL CONSIDERATIONS
The Gantrail clip needs to be selected to be able to carry the horizontal wheel load ensuring that it will fit on
the structure supporting the rail. Calculations have shown that when a wheel is over a pair of clips and is
applying the design horizontal load, there will be no significant horizontal load carried by the pairs of clips to
either side. It can also be shown that for crane rails, there is no consistency between the vertical wheel load
carrying capacity and the horizontal bending characteristics. For example, the Rodange MRS87A from the
steel maker Acelor in Luxembourg and the German DIN 536 A100 rail have top flange widths of 102 and 100
mm respectively. Thus they have the substantially the same wheel load capacity. However, the horizontal
bending moments of the rails are 975 and 1345 units respectively. The A100 is more than 40% stiffer than
the MRS87A. For this reason it is not feasible to develop a calculation method for clip spacing solely on
horizontal bending.

SUGGESTED SPACING
Experience has shown that crane rail clips spaced at about 600 mm work well. When the spacing exceeds
say 1 metre problems are often encountered. It is reasonable to have some difference in spacing based on
the actual duty. Thus the following clip spacing is suggested:
Normal applications - Clip Spacing 600 to 650 mm
Heavy duty applications and applications with guide rollers - Clip Spacing 500 mm.
(Note that guide rollers typically apply the horizontal load some distance from the vertical load; hence
the vertical wheel load cannot anchor the rail against horizontal force.)
Light duty applications - Clip Spacing 800 mm

TGN11/09/12

1 of 2

Lateral load capacity of Gantrail clips

OTHER CONSIDERATIONS
Further matters may need to be considered. For example:
With high bay warehouse cranes, the clip spacing should be a whole number division of the crane
wheel base. This prevents sway of the tall crane structure during long travel motion.
With concrete mounted rail it may be desirable to choose a spacing that coincides with the spacing of
the reinforcement cage. The drilling may then in theory be planned to miss the steel reinforcement.

TGN11/09/12

2 of 2

You might also like