MANDATORY APPENDIX 4
ROUNDED INDICATIONS CHARTS
ACCEPTANCE STANDARD FOR
RADIOGRAPHICALLY DETERMINED
ROUNDED INDICATIONS IN WELDS
4-1
(1) 110 t for t less than 18 in. (3 mm)
(2) 164 in. for t from 18 in. to 14 in. (3 mm to
6 mm), incl.
(3) 132 in. for t greater than 14 in. to 2 in. (6 mm
to 50 mm), incl.
(4) 116 in. for t greater than 2 in. (50 mm)
(c) Maximum Size of Rounded Indication. (See Table
4-1 for examples.) The maximum permissible size of any
indication shall be 14t, or 532 in. (4 mm), whichever is
smaller; except that an isolated indication separated from
an adjacent indication by 1 in. (25 mm) or more may be
1
3t, or 14 in. (6 mm), whichever is less. For t greater than
2 in. (50 mm) the maximum permissible size of an isolated
indication shall be increased to 38 in. (10 mm).
(d) Aligned Rounded Indications. Aligned rounded
indications are acceptable when the summation of the
diameters of the indications is less than t in a length of
12t. See Fig. 4-1. The length of groups of aligned rounded
indications and the spacing between the groups shall meet
the requirements of Fig. 4-2.
(e) Spacing. The distance between adjacent rounded
indications is not a factor in determining acceptance or
rejection, except as required for isolated indications or
groups of aligned indications.
(f) Rounded Indication Charts. The rounded indications characterized as imperfections shall not exceed that
shown in the charts. The charts in Figs. 4-3 through 4-8
illustrate various types of assorted, randomly dispersed
and clustered rounded indications for different weld thicknesses greater than 18 in. (3 mm). These charts represent
the maximum acceptable concentration limits for rounded
indications. The charts for each thickness range represent
full-scale 6 in. (150 mm) radiographs, and shall not be
enlarged or reduced. The distributions shown are not
necessarily the patterns that may appear on the
APPLICABILITY OF THESE
STANDARDS
These standards are applicable to ferritic, austenitic,
and nonferrous materials.
4-2
TERMINOLOGY
(a) Rounded Indications. Indications with a maximum
length of three times the width or less on the radiograph
are defined as rounded indications. These indications may
be circular, elliptical, conical, or irregular in shape and
may have tails. When evaluating the size of an indication,
the tail shall be included. The indication may be from
any imperfection in the weld, such as porosity, slag, or
tungsten.
(b) Aligned Indications. A sequence of four or more
rounded indications shall be considered to be aligned
when they touch a line parallel to the length of the weld
drawn through the center of the two outer rounded indications.
(c) Thickness t. t is the thickness of the weld, excluding
any allowable reinforcement. For a butt weld joining two
members having different thicknesses at the weld, t is
the thinner of these two thicknesses. If a full penetration
weld includes a fillet weld, the thickness of the throat of
the fillet shall be included in t.
4-3
ACCEPTANCE CRITERIA
(a) Image Density. Density within the image of the
indication may vary and is not a criterion for acceptance
or rejection.
(b) Relevant Indications. (See Table 4-1 for examples.) Only those rounded indications which exceed the
following dimensions shall be considered relevant.
368
--`,,```,,,,````-`-`,,`,,`,`,,`---
Copyright ASME International
Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS
Not for Resale
4-3
MANDATORY APPENDIX 4
TABLE 4-11
radiograph, but are typical of the concentration and size
of indications permitted.
(g) Weld Thickness t less than 1/8 in. (3 mm). For t
less than 18 in. (3 mm) the maximum number of rounded
indications shall not exceed 12 in a 6 in. (150 mm) length
of weld. A proportionally fewer number of indications
shall be permitted in welds less than 6 in. (150 mm) in
length.
(h) Clustered Indications. The illustrations for clustered indications show up to four times as many indications in a local area, as that shown in the illustrations for
random indications. The length of an acceptable cluster
shall not exceed the lesser of 1 in. (25 mm) or 2t. Where
more than one cluster is present, the sum of the lengths
of the clusters shall not exceed 1 in. (25 mm) in a 6 in.
(150 mm) length weld.
Customary Units
Maximum Size of
Acceptable Rounded
Indication, in.
Random
Isolated
Maximum Size of
Nonrelevant
Indication, in.
4t
0.031
0.047
0.063
3t
0.042
0.063
0.083
10t
0.015
0.015
0.015
16
3
8
7
16
1
2
0.078
0.091
0.109
0.125
0.104
0.125
0.146
0.168
0.031
0.031
0.031
0.031
16
5
8
11
16
0.142
0.156
0.156
0.188
0.210
0.230
0.031
0.031
0.031
4 to 2, incl.
Over 2
0.156
0.156
0.250
0.375
0.031
0.063
Thickness t,
in.
1
Less than 8
1
8
3
16
1
4
SI Units
Maximum Size of
Acceptable Rounded
Indication, mm
--`,,```,,,,````-`-`,,`,,`,`,,`---
Thickness t,
mm
Random
1
Isolated
1
Maximum Size of
Nonrelevant
Indication, mm
1
Less than 3
3
5
6
4t
0.79
1.19
1.60
3t
1.07
1.60
2.11
10t
0.38
0.38
0.38
8
10
11
13
1.98
2.31
2.77
3.18
2.64
3.18
3.71
4.27
0.79
0.79
0.79
0.79
14
16
17
3.61
3.96
3.96
4.78
5.33
5.84
0.79
0.79
0.79
19.0 to 50, incl.
Over 50
3.96
3.96
6.35
9.53
0.79
1.60
NOTE:
(1) This Table contains examples only.
369
Copyright ASME International
Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS
4-3
Not for Resale
Copyright ASME International
Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS
L1
L1
370
--`,,```,,,,````-`-`,,`,,`,`,,`---
Not for Resale
3L 3
L3
ALIGNED ROUNDED INDICATIONS
3L 3
FIG. 4-2
GROUPS OF ALIGNED ROUNDED INDICATIONS
Minimum Group Spacing
3L where L is the length of the
longest adjacent group being
evaluated.
GENERAL NOTE: Sum of the group lengths shall be less than t in a length of 12t.
L2
FIG. 4-1
GENERAL NOTE: Sum of L1 to Lx shall be less than t in a length of 12t.
Maximum Group Length
L = 1/4 in. (6 mm) for t less than 3/4 in. (19 mm)
L = 1/3t for t 3/4 in. (19 mm) to 21/4 in. (57 mm)
L = 3/4 in. (19 mm) for t greater than 21/4 in. (57 mm)
3L2
L2
Lx
L4
2004 SECTION VIII DIVISION 1
MANDATORY APPENDIX 4
(a) Random Rounded Indications [See Note (1)]
1 in. (25 mm)
1 in. (25 mm)
(c) Cluster
(b) Isolated Indication [See Note (2)]
NOTES:
(1) Typical concentration and size permitted in any 6 in. (150 mm) length of weld.
(2) Maximum size per Table 4-1.
FIG. 4-3 CHARTS FOR t EQUAL TO 18 in. to 14 in. (3 mm to 6 mm), INCLUSIVE
(a) Random Rounded Indications [See Note (1)]
--`,,```,,,,````-`-`,,`,,`,`,,`---
1 in. (25 mm)
1 in. (25 mm)
(c) Cluster
(b) Isolated Indication [See Note (2)]
NOTES:
(1) Typical concentration and size permitted in any 6 in. (150 mm) length of weld.
(2) Maximum size per Table 4-1.
FIG. 4-4 CHARTS FOR t OVER 14 in. to 38 in. (6 mm to 10 mm), INCLUSIVE
371
Copyright ASME International
Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS
Not for Resale
2004 SECTION VIII DIVISION 1
(a) Random Rounded Indications [See Note (1)]
1 in. (25 mm)
1 in. (25 mm)
(c) Cluster
(b) Isolated Indication [See Note (2)]
NOTES:
(1) Typical concentration and size permitted in any 6 in. (150 mm) length of weld.
(2) Maximum size per Table 4-1.
FIG. 4-5 CHARTS FOR t OVER 38 in. to 34 in. (10 mm to 19 mm), INCLUSIVE
372
--`,,```,,,,````-`-`,,`,,`,`,,`---
Copyright ASME International
Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS
Not for Resale
MANDATORY APPENDIX 4
(a) Random Rounded Indications [See Note (1)]
--`,,```,,,,````-`-`,,`,,`,`,,`---
1 in. (25 mm)
1 in. (25 mm)
(c) Cluster
(b) Isolated Indication [See Note (2)]
NOTES:
(1) Typical concentration and size permitted in any 6 in. (150 mm) length of weld.
(2) Maximum size per Table 4-1.
FIG. 4-6 CHARTS FOR t OVER 34 in. to 2 in. (19 mm to 50 mm), INCLUSIVE
373
Copyright ASME International
Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS
Not for Resale
2004 SECTION VIII DIVISION 1
(a) Random Rounded Indications [See Note (1)]
1 in. (25 mm)
1 in. (25 mm)
(c) Cluster
(b) Isolated Indication [See Note (2)]
NOTES:
(1) Typical concentration and size permitted in any 6 in. (150 mm) length of weld.
(2) Maximum size per Table 4-1.
FIG. 4-7 CHARTS FOR t OVER 2 in. to 4 in. (50 mm to 100 mm), INCLUSIVE
374
--`,,```,,,,````-`-`,,`,,`,`,,`---
Copyright ASME International
Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS
Not for Resale
MANDATORY APPENDIX 4
(a) Random Rounded Indications [See Note (1)]
1 in. (25 mm)
1 in. (25 mm)
(b) Isolated Indication [See Note (2)]
(c) Cluster
NOTES:
(1) Typical concentration and size permitted in any 6 in. (150 mm) length of weld.
(2) Maximum size per Table 4-1.
FIG. 4-8 CHARTS FOR t OVER 4 in. (100 mm)
375
--`,,```,,,,````-`-`,,`,,`,`,,`---
Copyright ASME International
Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS
Not for Resale
