Scribd
Upload
2K views6 pages

Travelling Block

This document provides information on Type H traveling blocks manufactured by ARMCO National Supply Company, including: 1) A parts list that describes each part needed for the Type H traveling block and provides the corresponding part number. 2) A lubrication schedule that lists lubrication check points, recommended lubricants, and lubrication procedures and frequency. 3) A maintenance checklist that outlines precautionary maintenance measures and an operating maintenance schedule listing specific checks to perform on the traveling block components on a quarterly basis.

Uploaded by

Sasan Abbasi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
2K views6 pages

Travelling Block

This document provides information on Type H traveling blocks manufactured by ARMCO National Supply Company, including: 1) A parts list that describes each part needed for the Type H traveling block and provides the corresponding part number. 2) A lubrication schedule that lists lubrication check points, recommended lubricants, and lubrication procedures and frequency. 3) A maintenance checklist that outlines precautionary maintenance measures and an operating maintenance schedule listing specific checks to perform on the traveling block components on a quarterly basis.

Uploaded by

Sasan Abbasi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

NATIONAL

TRAVELING BLOCKS

EFFECTIVE OCTOBER 15, 1976

ARMCO National Supply Company


@

Division of Armco

,455 West LOO, S ~ u t h H


, O L I S ~Texas
O ~ , 77027

TYPE "H" TRiZVELISG BLOCKS

Item

Description
Qty.

Housing Assembly

Part

Qty.

Part

I ~ t y . part

I ~ t y . part
642260-A

649499-A

Guard Installation

642264-G

Cap

642266

Pin, Cap

642267

Shaft

642268

Nut, Shaft

642269

Retainer, Bearing

623238

Key

642103

Clevis

642273

Pin, Clevis

642274

Pin, Guard Hinge

642275

Plate, Name

642276

Bearing

ZT-8003

Bushing, A-112 Alen~ite

7801620

Fitting, 1610-BL -4lemite

7805052

Plug, 1" Std C'sk M.I.

6875008

Screw, % " x l l h " Hex Soc Hd Cap

7006438

Screw, %" x 2" Hex Hd Cap

7000481

Nut, Thin Hex Slotted

2 ' i " -8N


6324363

Nut, Thin Hex Slotted

3" -8N
6324483

Washer, % " Reg Lock

7602066

Washer, '6" Reg Lock

7602074

Pin, Cotter

36" x 312"
6502428

Pin. Cotter

14" x 41.''
6503236

Screw, #6 x 5/16" Rd Hd Dr

7178063-30

Sheave
Sheave
Sheave

for 1%"line
645372-6

f o r 13h" line
645372-5

for 13k" line


642100

for 15" line


645372-7

f o r 1 % " line
645372-4

for I f & " line


642101

f o r 1 % " line/
645372-8

When ordering, please specify serial number of unit and description of parts.
Manufactured By

ARMCO National Supply Company


Division of Arrnco Steel Corporation
\
@

Torrance, California

1
1

f o r 1';" line
642270
f o r 13k" line
642271

MAINTENANCE CHECKLIST

NATIONAL TYPE ti TRAVELING BLOCK

LUBRICATION SCHEDULE
FREQUENCY

CHECK POINT

TYPE

PROCEDURE

Sheave bearings
after tripping

[AJ

Multipurpose grease*

1-3 strokes of hand grease gun


at each fitting

*Multipurpose Lithium base grease


Below 32OF (OC) NLGl #1
Above 32: F (0"C) NLGl #2

PRECAUTIONARY MEASURES
Keep traveling block clean.
Caps screws, nuts and pinned connections should be checked occasionally for looseness and wear.
Remove any rust and weather protect.
Keep bearings properly and adequately lubricated.
Proper grounding procedures should be taken if welding on block sideplates to avoid arcing of bearings.
Do not weld on clevis.

ARMCO National Supply Company

IADC APPROVED FORMAT

6-1-81

Division of Arrnco Inc.


Houston,Texas 77027

MAINTENANCE CHECKLIST

NATIONAL TYPE H TRAVELING BLOCK

OPERATING MAINTENANCE
FREQUENCY*

CHECK
POINT

PROCEDURE

Quarterly

0
0

Quarterly

Quarterly

Quarterly

Check clevis pin for wear and cracks.

Quarterly

Check clevis for excessive wear and cracks at pin eye and saddle area.

Quarterly

Check lifting eye in top of cap for excessive wear and cracks.
Check sheave grooves for excessive wear (API RPSB), cracks and sheave
wobble.
Check shaft ends for cracks and deformation.
Check block housing and clevis junction for wear and cracks (especially in
the weld attaching clevis hangers to side plates and pin eye area of clevis
hangers).

*Refer to API RPBB for recommended inspection of traveling block assemblies.


EXAMPLE: Section 2 Para 2.1.3 Frequency of Inspection Critical Load Inspection. Critical loads may be
experienced; for example, severe loads, impact loads such as jarring, pulling on stuck pipe, and/or
operating at low temperatures. If in the judgment of the supervisor a critical load has occurred, or may
occur, an on-the-job shutdown inspection equivalent to the periodic field inspection should be done. If
critical loads are anticipated, the inspection should be conducted prior to and after the occurrence of
such loading. If critical loads are unexpectantly encountered, inspection should be conducted
immediately after such an occurrence.

ARMCO National Supply Company

IADC APPROVED FORMAT

6-1-81

Division of Armco Inc.


Houston, Texas 77027

You might also like