Ethernet TCP/IP
BC9000, BC9050
Power-LEDs
K-bus
Ethernet RJ 45
Bus Coupler
supply
Input for
power contacts
Address selector
Configuration and
programming interface
Power contacts
BC9000, BC9050 | Ethernet TCP/IP Bus Terminal Controllers
The Bus Terminal Controllers BC90x0 are Bus Couplers with integrated PLC functionality and have a fieldbus interface for Ethernet.
They are intelligent slaves that can be used as a non-central intelligence in the Ethernet system. One unit consists of the Bus
Terminal Controller, any number of terminals between 1 and 64, and a bus end terminal. The Compact BK9050 Bus Terminal
Controller is a cost-optimised version with compact housing. With the K-bus extension, up to 255 Bus Terminals can be connected.
The Bus Terminal Controller is programmed using the TwinCAT programming system according to IEC 61131-3. The configuration/programming interface
of the BC9000 or BC9050 is used for loading the PLC program. If the software PLC TwinCAT is in use, the PLC program can also be loaded via Ethernet.
In the default setting the inputs and outputs of the connected Bus Terminals are assigned to the controller. Each Bus Terminal can be configured in such
a way that it exchanges data directly through the fieldbus with the higher-level automation device.
Controller for distributed signal processing
The BC9000 and BC9050 Bus Terminal Controllers support the operation of all Bus Terminal types. As far as the user is concerned, the inputs and
outputs are not handled any differently from the way they are by other coupler series. The information is made available for use as a byte array in the
process image of the automation device.
The analog and multi-functional Bus Terminals can be adapted to each specific application using the KS2000 configuration set. Depending on the type,
the analog Bus Terminals' registers contain temperature ranges, gain values and linearisation characteristics. With the KS2000, the required parameters
can be set on a PC. The Bus Terminals store settings permanently and in a fail-safe manner.
Having the controller (PLC, IPC) carry out the configuration of the Bus Terminals is a further option. The PLC or IPC uses function blocks (FB) to take care
of the configuration of all the peripherals during the start-up phase. The controller can, if required, upload the non-centrally generated configuration
data in order to manage and store them centrally. This means that it is not necessary to carry out the setting procedure again if a Bus Terminal is
exchanged. The controller carries out the desired setting automatically after switching on.
PLC data
Ethernet TCP/IP | BC9000
Programming
via TwinCAT and programming interface or Ethernet
Program memory
64/96 kbytes
48 kbytes
Data memory
64/128 kbytes
32 kbytes
Remanent data
4,080 bytes
2 kbytes
Run-time system
1 PLC task
PLC cycle time
approx. 1.5 ms for 1,000 instructions (without I/O cycle, K-bus)
Programming languages
IEC 61131-3 (IL, LD, FBD, SFC, ST)
Online change
BECKHOFF New Automation Technology
BC9050
yes
We reserve the right to make technical changes.
Technical data
BC9000
BC9050
Number of Bus Terminals
64
64 (255 with K-bus extension)
Max. number of bytes fieldbus
512 byte input and 512 byte output
Max. number of bytes process
image
512 byte input and 512 byte output
2,048 byte input and 2,048 byte output
Digital peripheral signals
512 inputs/outputs
2,040 inputs/outputs
Analog peripheral signals
128 inputs/outputs
512 inputs/outputs
Protocol
TwinCAT ADS, Modbus TCP
Configuration possibility
via KS2000 or Ethernet
Data transfer rates
10/100 Mbaud, automatic recognition of the transmission rate
Bus interface
1 x RJ 45
Power supply
24 V DC (-15 %/+20 %)
Input current
70 mA + (total K-bus current)/4, 500 mA max.
Starting current
2.5 x continuous current
Recommended fuse
10 A
Current supply K-bus
1,750 mA
Power contacts
24 V DC max./10 A max.
Electrical isolation
500 V (power contact/supply voltage/fieldbus)
Weight
approx. 170 g
Operating/storage temperature
0+55 C/-25+85 C
Protect. class/installation pos.
IP 20/variable
Approvals
CE, UL, Ex, GL
320 mA max.
1,000 mA
approx. 100 g
CE, UL, Ex
Accessories
KS2000
configuration software for extended parameterisation
TwinCAT PLC
programming system conforms to IEC 61131-3
Cordsets
cordsets and connectors
FC90xx-00xx
PC Fieldbus Cards with PCI interface
Ordering information
Description
BC9000
Ethernet Bus Terminal Controller for up to 64 Bus Terminals
BC9050
Ethernet Compact Bus Terminal Controller for up to 64 Bus Terminals (255 with K-bus extension)
BC9020
Ethernet TCP/IP Economy plus Bus Terminal Controller for up to 64 Bus Terminals (255 with K-bus extension)
BC9100
Ethernet TCP/IP Bus Terminal Controller for up to 64 Bus Terminals (with integrated 2-channel switch)
BC9120
Ethernet TCP/IP Economy plus Bus Terminal Controller for up to 64 Bus Terminals (255 with K-bus extension, with
integrated 2-channel switch)
BX9000
Ethernet Bus Terminal Controller for up to 64 Bus Terminals (255 with K-bus extension)
BK9xx0
Ethernet Bus Coupler
CX8090
Ethernet Embedded PC
BECKHOFF New Automation Technology
We reserve the right to make technical changes.
