Scribd
Upload
768 views4 pages

JSA For Flue Gas Duct Height Work

1. The document outlines safety measures for work being conducted on a flue gas duct, including installing edge protection, anchorage points for harnesses, controlling materials, barricading areas, and using proper tools and PPE. 2. Specific hazards addressed for various activities include falling, falling materials, shifting metal sheets, grinding risks like sparks and rotating equipment, and fire risks of welding. 3. Control measures specified include installing railings, harness anchors, controlling materials, barricades, safe handling techniques, inspections, proper equipment use, fire equipment and trained personnel, gas monitors, and more. Verification is made that the crew understood the discussed safety points.

Uploaded by

subhadipmanna8
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
768 views4 pages

JSA For Flue Gas Duct Height Work

1. The document outlines safety measures for work being conducted on a flue gas duct, including installing edge protection, anchorage points for harnesses, controlling materials, barricading areas, and using proper tools and PPE. 2. Specific hazards addressed for various activities include falling, falling materials, shifting metal sheets, grinding risks like sparks and rotating equipment, and fire risks of welding. 3. Control measures specified include installing railings, harness anchors, controlling materials, barricades, safe handling techniques, inspections, proper equipment use, fire equipment and trained personnel, gas monitors, and more. Verification is made that the crew understood the discussed safety points.

Uploaded by

subhadipmanna8
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

Department

:
Activity:
Location:
Date :

Sr.
No.

Activity

1.

Access
to Fall
of Safe
Access
should
be
Flue
Gas personnel
provide to landing area of
Duct
Flue gas Duct.
Landing
Area
Installing of
Fall of
Install Edge Protection (Top
Edge
personnel
rail and Mid rail) with
Protection
adequate strength
with
scaffolding Pipe around the
Flue duct landing area
Install Anchorage Point at
middle of Flue Gas Duct area
for anchoring Full Body
Safety Harness.
All Personnel should use
Mandatory PPEs and Full
Body Safety harness during
working over Flue Gas Duct
Fall of Material
Ensure all materials are kept
in middle, no loose materials
to be kept at edge of Flue
Gas Duct.
Hand Tools to be tied with
Rope with hand.
Only Standard Tools to be
used.
Barricading the area below
and Stand by personnel to be
provided for not allowing any
unauthorized personnel at
underneath of work area
Shifting
of Fall of Metal Safe Handling of sheet to be
Metal Sheet Sheet
ensured.
Fixing
of Fall of Metal Personnel should be working

3
4

Potential
Hazards
Effects

Safe
& Practices/Control
Measures

work Remark
s

Metal
Sheeting
5
Grinding

Sheet and Fall by sitting over Flue gas duct


of Personnel
top floor only.
Adequate Support should be
provided on metal sheet.

Make sure guards are


Rotating
fitted to all moving parts
equipmen
Ensure the proper use
t sparks.
of guards
Damaged
Inspect the grinding
grinding
discs prior to starting work
disc
(ring test)

Make sure that disc is


compatible
with
the
grinding machine

Check the RPM of disc


Electrocut
& machine
ion.

Proper PPE (Gloves +


Mask).
High

Correct installation of
Pressure
Grinder Wheel.
air

Gas monitor correctly


sited.
Flying

Spark containment to
object/ey
be used.
e injuries
Only
experienced
personnel to use the
equipment.

Wear a face shield


while grinding
Make sure an eye wash
station is available nearby
Ensure Grinding Sparks are
not
falling
below
underneath of work area

Fire Hazard
Welding

Before starting welding


make sure the area is
clear of all types of
combustible materials

Gas test to be carried out


before entry to ensure
concentration
of
flammable gases is zero.

Provide a fire blanket on


site

Make
sure
extinguishers

Burns.
Electrocution/
Spatter burns
Damage cable
Hot tabs end
pieces
of
welding rods.
Sparking

fire
are

available on site

Damage cable

Wear proper PPE for


welding
ie.,
leather
jackets, Gloves, welding
goggles/welding mask,

RCCB to be ensured.

Trained Fire Watch.

Gas Monitor
sited.

Certified Equipment and


to be sited as near as
possible to work site.

Proper
earthing
equipment.

Certified Welder.

Make
sure
spark
containment is used such
as a welding hood/fire
blanket.

Ensure that rod holder is


in good condition.

Ensure that forward and


return cables are in good
working condition.

Use
proper
cable
connector for extension.

If cables are crossing the


road then ensure proper
protection.

The welder & the welder


helpers
must
wear
welding goggles

UV rays

correctly

of

Above points have been discussed and conveyed to the crew / team members
of the task. It is verified that they understood the discussion points.

Name and Sign


Work In-charge

Name & Sign


(HOD)

You might also like