METAL PASSAGE CONFIRMATION SENSORS

APPLICATIONS
Accurately counts falling screws

Confirmation of part ejection

from presses

MDA-001

MSC-050

Remark:
These products are not designed for wire break detection

Z- 01

METAL PASSAGE CONFIRMATION SENSORS

SELECTION CHART
Amplifier Unit

SENSOR

POWER

EN

SITIVI

OPERATION

MDA-001
METAL DETECTOR
AMPLIFIER

Output

Power supply

Min

T
Y

METAL PASSAGE CONFIRMATION

SENSORS

Shape

Max

AC 110/220V
50/60Hz

Relay contact: SPDT AC250V 2A/DC 30V 3A

Solid state: Open-collect or 100mA Max.

Model

MDA-001

Sensor head

Shade

Smallest Detectable object

Model

50

Non-isolate

2.0mm dia. steel ball

MSC-050

75

Non-isolate

2.5mm dia. Steel ball

MSC-075

100

Non-isolate

3.0mm dia. steel ball

MSC-100

150 x 100
(L x W)

Non-isolate

5.0mm dia. Steel ball

MSR-150

7.0mm dia. steel ball

MSR-200

200 x 150
(L x W)

Non-isolate

Z- 02

METAL PASSAGE CONFIRMATION SENSORS

SPECIFICATIONS
Power supply

AC 110/220V +10% 50/60Hz

Power consumption

3VA Max.

Sensitivity adjustment

By sensitivity selector switch and fine-adjustment trimmer

Solid-State

Normal/OFF delay 40ms ( by switch )

Relay Contact

ONE-SHOT 40ms ( fixed )

Normal

Time interval
of detection
(Note)

Solid-State

OFF delay

75ms Max.
125ms Max.

Relay Contact

75ms Max.

Solid-State

Open-collector:100mA max. ( DC40V )

Relay Contact

SPDT 250VAC 2A ( resistive ) ; 30VDC 3A ( resistive )

Control Output

Sensor Adapt

All models of Metal Passage Confirmation Sensors

Correct Cable length

By switch

Output Status

NO/NC Changeable ( By switch )

Indicator

Power Indicator & Operation Indicator

Operating Temperature

-10 C ~ +55 C

Operating Humidity

35~ 85%RH

Isolate Resistance

50M Max. ( 500VDC MEGA ) one time across power terminal & exposed
Metal, two times at all terminal ( non-contact output and sensor ).

Voltage Resistance

AC 1,500V, 50/60Hz 1 min one time across power terminal & exposed
metal, two times at all terminal ( non-contact output & sensor; contact ).

Vibration Resistance

directions,2 hours respectively 10 to 55Hz, 1.5mm double amplitude in X, Y,

and Z

Shock Immunity

100m/s2 10G in X, Y, and Z directions,3 times respectively

Protection Category

IP30

Weight

Approx.300g

Note: Time used in detecting smallest detectable size object, longer detection time if object is larger.

Z- 03

METAL PASSAGE CONFIRMATION

SENSORS

Timers

METAL PASSAGE CONFIRMATION SENSORS

Sensor head
Type
Item
Detection Area

METAL PASSAGE CONFIRMATION

SENSORS

Detection Object

MSC-050

MSC-075

MSC-100

50mm dia.

75mm dia.

100mm dia.

Moving Ferrous Metal ( sensibility of non-ferrous metal is low )

2.5mm dia.
Steel ball

2.0mm dia.
Steel ball

Min. Target
Operating Temperature

3.0mm dia.
Steel ball

-25 C ~ +70 C ( Without icing )

35-90%RH

Operating Humidity
Isolate Resistance

Except for expose head & isolate wire with connection

Voltage Resistance

Except for expose head & isolate wire with connection

Vibration Resistance

10 to 55Hz,1.5mm double amplitude in X, Y, and Z directions,2 hours respectively

50G in X, Y, and Z directions,3 times respectively

Shock Immunity
Cable

3m ( Coaxial Cable )

Weight

Approx.430g

Approx.800g

Protection Category

Approx.1200g

IP67

Housing

ALUMINIUM

Material
Sensor Face

Type
Item
Detection Area

ABS

MSR-150

MSR-L200

100x150mm

200(L)x150(W)

Detection Object

Moving Ferrous Metal ( sensibility of non-ferrous metal is low )

Min. Target

5.0mm dia. Steel ball

Operating Temperature

7.0mm dia. Steel ball

-25 C ~ +70 C ( Without icing )

Operating Humidity

35-90%RH

Isolate Resistance

50M
AC 1,000V/min

Voltage Resistance
Vibration Resistance

10 to 55Hz,1.5mm double amplitude in X,Y,and Z directions,2 hours respectively

Shock Immunity

50G in X,Y,and Z directions,3 times respectively

Cable

3m ( Coaxial Cable )

Weight

Approx.1,300g
IP67

Protection Category
Housing

Approx.2,100g

ALUMINIUM

ABS

Material
Sensor Face

ABS

Z- 04

METAL PASSAGE CONFIRMATION SENSORS

PRECAUTIONS FOR PROPER USE
Disturb of the around metal
When mounting on a steel base, follow the guidelines below to prevent detection of the mounting material.

Dimension
MSC-050

150

30

MSC-075

200

40

MSC-100

300

50

MSR-150

Model

Model

MSR-200

Model

Model

UNIT: mm

When mounting on an iron base is necessary, follow the guidelines given below must be satisfied. Otherwise,
it may be resulted in a mistake operation.

MSC-050

MSR-150

Drop through mount: Drill a hole

With min. diameter 0f 112mm.

Metal

Metal

112
11

110

MSC-075

110

Metal

Drop through mount: Drill a hole

With min. diameter 0f 150mm.

MSR-200

34mm Max.

150

140
Metal

Metal

140

MSC-100

Metal

25mm Max.
Metal

Metal

Note: The type of MSR-150 5.0 & MSR-200 7.0 should

be mounted on the surface in order to minimize the
interference of metal.

Z- 05

METAL PASSAGE CONFIRMATION

SENSORS

Model

Moving metal

METAL PASSAGE CONFIRMATION SENSORS

Interference of sensor each other

METAL PASSAGE CONFIRMATION

SENSORS

When installing 2 or more sensors of the same model in close proximity, it is necessary to connect the
grounding screw to the machine ground and to maintain spacing greater than the distance shown in
the following table to prevent interference.

Model

Dimension

Series(d1)

Parallel(d2)

MPC-050N32.0

150

30

MPC-075N32.5

200

40

MPC-100N33.0

300

50

MPR-150N35.0

Model

Model

MPR-200N37.0

Model

Model
UNIT: mm

Other precautions:
The operation of the sensor is stable 1 to 2 seconds after the power is applied. Do not use sensor
signal immediately on power-up.
In order to prevent interference, keep exposed
cable wire 10mm or less.(see diagram)

10mm Max.

When target has stopped or a wire break occurs,

the output is ONE PULSE (40ms)
,

Do not touch the sensor s active face at the status

of high sensitivity, because a touch by hand will be
detected.

CHARACTERISTICS
Target speed-size chart

MSC-050

MSC-075
Fall height
(m)
20

Speed 20
V(m/s)
Iron

Brass

15

Speed
V(m/s)

Fall height
(m)

20

15

Target Fall height

20

Iron

15

Brass Target Fall height

15
10

10

Check
domain
5

Check
domain
5

1.4
1

Target size

1.4

0.1
0

5
4
3
2

10

5
4
3
2

10

0.1
0

10

(mm)

Target size

Z- 06

10

(mm)

METAL PASSAGE CONFIRMATION SENSORS

MSC-100
Fall height

Speed
V(m/s) 20
Target

(m)
20

Iron

Fall height

15

brass

15

10

Check
domain

1.4
0

METAL PASSAGE CONFIRMATION

SENSORS

5
4
3
2

10

0.1
1

10
Target size (mm)

Output residuary voltage

Residuary voltage
(V)
1.2
1.1
1.0
0.9
0.8
0.7
0.6
1

3 5 7 10

30 50 70 100

300 500

ACTION CHART
Detects object

PASSAGE

Action method

N.O.
N.C.

Timer shift

TIMER
NORMAL

Solid-contact

ON
OFF

Relay-contact

ON
OFF

Detects indicator

ON
OFF

Power indicator

ON
OFF

NO

Note 1: When a target is passing, the

Output of the contact is on,
while the non-contact is
Changeable ( N.O. Or N.C. ).

A
B

power off

Z- 07

Note 2: Output of the contact is oneshot type. It can output a

40ms fixed pluse-width
Independent of the time the
target present.
A: 40ms(OFF DELAY)
B: 40ms(ONE SHOT)

METAL PASSAGE CONFIRMATION SENSORS

MDA-001

METAL PASSAGE CONFIRMATION

SENSORS

75

67.5

66
2-M4
57.3

74

MSC-50

MSC-75

10
91

130
110

31.5

4-7

10

10

50

96

110

154

76

75

M4

50
10

5.5

25
74
110

17

10

23

10

21.5

16.5

40

7
6

16

26 10

20
8

94

126

Z- 08

25

R3.5

METAL PASSAGE CONFIRMATION SENSORS

MSC-75
170

M4
18

140

10

100

METAL PASSAGE CONFIRMATION

SENSORS

180

31.5

4-7

140

5.5

100

16

10

20

15

21.5

16.5

45

7
16
20
R3.5

126

MSR-150

MSR-200

4x6
30

56 44 30

16

260

236
300
200

220

150

170 100

240 150
5.4
5.4

10

20

47
10

252

Z- 09

25