PCM-5862/L Pentium-based SBC with Audio, Ethernet,and VGA/LCD
PCM-5862/5862L Pentium-based SBC with
Audio, VGA/LCD, and Ethernet
Startup Manual
Packing list Specifications
Before you begin installing your card, please make
Standard SBC functions
sure that the following materials have been shipped:
CPU:
1 PCM-5862/5862L All-in-one single board computer
Intel Pentium , Pentium MMX, up to 233
1 Startup Manual MHz
AMD K5
1 CD-ROM or disk for utility, drivers, and manual (in Cyrix 6x86
pdf format)
BIOS: AWARD 128 KB Flash BIOS, supports
Plug&Play, APM
If any of these items are missing or damaged, contact Chipset: SiS 5571
your distributor or sales representative immediately.
Green function: APM 1.1 compliant
Note: For detailed contents of the 2nd level cache: On-board 512 KB Pipelined
PCM-5862/5862L, please refer to the Burst SRAM
enclosed CD-ROM or Disk (in
PDF format). RAM: Two 72-pin SIMM sockets accept 8 ~
128 MB EDO/FPM DRAM
Enhanced IDE interface: Supports two EIDE
devices
FDD interface: Supports up to two FDDs (360
K / 1.2 M / 720 K / 1.44 MB / 2.88 MB)
Parallel port: One parallel port, supports SPP/
EPP/ECP parallel mode
Serial ports: Four serial RS-232 ports; three
RS-232 (COM1, 3, 4)and one RS-232/422/485
(COM2). All ports with 16C550 compatible
UARTs
Watchdog timer: 63-level interval from 1 ~ 63
seconds. Generates system reset or IRQ15.
Jumperless selection and software enabled/
disabled
Keyboard/mouse connector: 8-pin header
connector for keyboard and PS/2 mouse
USB interface: two USB connectors with fuse
protection. Compliant with USB Spec. Rev. 1.0
(optional)
PC/104 expansion: 104-pin 16-bit PC/104
module connector
For more information on this and other Advantech I/O bus expansion: One 32-bit PCI bus
products please visit our website at: expansion slot
http://www.advantech.com
http://www.advantech.com/epc PCI SVGA/flat panel interface
For technical support and service for please visit our Chipset: C&T 65550
support website at:
Display memory: 1 MB on-board memory,
http://support.advantech.com supports up to 2 MB
This manual is for the PCM-5862/5862L. Display type: Simultaneously supports CRT
and flat panel (EL, LCD, and gas plasma)
Part No. 2006586230 1st edition displays
Printed in Taiwan July 1999
CRT resolution: Supports non-interlaced CRT and J16 Audio power source setting
LCD monitors up to 1024 x 768 @ 256 colors with 1
MB on-board display memory Connectors
Label Function
Audio function (PCM-5862 only) CN1 CRT display connector
CN2 Flat panel display connector
Chipset: ESS 1868 or 1869
CN3 PC/104 ISA-bus expansion
Audio controller: 16-bit codec, Sound Blaster Pro CN4 USB channel 1 connector
compatible CN5 USB channel 2 connector
Stereo sound: Full-duplex, integrated 3D audio CN6 Fan power connector
CN7 Front panel connector
Audio interface: Microphone in, Line in, CD audio
in, Line out, Speaker out CN8 CD audio input connector
CN9 PC/104 ISA-bus expansion
Power: Accepts +12 V source for improved audio
CN10 Peripheral power connector
quality
CN11 Ethernet 10Base-T connector
CN12 IR connector
Ethernet interface
CN13 Audio connector
Chipset: REALTEK RTL8029 Ethernet controller CN14 Main power connector
CN15 Keyboard and PS/2 mouse
Ethernet interface: Novell NE2000 compatible
connector
10Base-T interface. Includes drivers & boot ROM
CN16 COM-port connector
CN17 IDE hard drive connector
Mechanical and environmental CN18 Floppy drive connector
Max. power requirements: 7 A @ 5 V (4.75 V ~ CN19 Parallel port connector
5.25 V)
Operating temperature: 0 ~ 60 C (32 ~ 140 F) Jumper settings
Size (L x W): 203 mm x 146 mm (8" x 5.75")
J1 & J2: System/PCI clock setting
Weight: 0.32 kg (0.7 lbs) (w/o package) System 50MHz 50MHz 60MHz *66MHz 75MHz
PCI 25 33.3 30 *33.3 32
1 3 5 1 3 5 1 3 5 1 3 5 1 3 5
J1
2 4 6 2 4 6 2 4 6 2 4 6 2 4 6
Jumpers and connectors 1 3 5 1 3 5 1 3 5 1 3 5 1 3 5
J2
The PCM-5862/5862L has a number of jumpers that
2 4 6 2 4 6 2 4 6 2 4 6 2 4 6
allow you to configure your system to suit your
applications. The table below lists the function of each
of the board's jumpers. J3: CPU voltage setting
2.5 V 2.8 V 3 V *3.3 V
1 3 1 3 1 3 1 3
Jumpers 2 4 2 4 2 4 2 4
Label Function
J1 System/PCI clock setting J4: CPU frequency ratio
J2 System/PCI clock setting 1.5 *2 2.5 3
J3 CPU voltage setting 1 3 5 1 3 5 1 3 5 1 3 5
J4 CPU frequency ratio setting/
P55C enabled/disabled 2 4 6 2 4 6 2 4 6 2 4 6
J5 M1 cache linear mode setting
J6 CMOS clear J4: P55C enabled/disabled
J7 Buzzer enable/disable
P55C enabled *P55C disabled
J8 COM4 IRQ occupied/released 1 3 5 1 3 5
J9 COM3 IRQ occupied/released
J10 LCD power setting
2 4 6 2 4 6
J11 COM4 RI pin setting
J12 COM3 RI pin setting
J13 Watchdog timer action
J14 COM2 RS-232/422/485 setting
J15 COM2 RS-232/422/485 setting
2 PCM-5862/5862L Startup Manual
J5: M1 cache linear mode enabled/disabled J14 & J15: COM2 RS-232/422/485
*enabled disabled *RS-232 RS-422 RS-485
1 3 5 1 3 5 1 3 5
J14
2 4 6 2 4 6 2 4 6
J6: Clear CMOS 12 11 10 12 11 10 12 11 10
*3.6 V battery on clear CMOS
1 2 3 1 2 3 J15
3 2 1 3 2 1 3 2 1
J7: Buzzer enabled/disabled
*enabled disabled J16: Audio power source setting
*+5 V +12 V
1 2 3 1 2 3
J8: COM4 IRQ occupied/released
*occupied released
J9: COM3 occupied/released
*occupied released
J10: LCD power setting
*5 V 3.3 V
1 3 5 1 3 5
2 4 6 2 4 6
J11: COM4 RI pin setting
+5 V +12 V *RI
1 3 5 1 3 5 1 3 5
2 4 6 2 4 6 2 4 6
J12: COM3 RI pin setting
+5 V +12 V *RI
1 3 5 1 3 5 1 3 5
2 4 6 2 4 6 2 4 6
J13: Watchdog timer action
*System reset IRQ15
1 1
2 2
3 3
Locating jumpers
Mechanical drawings
J13 J14
J15
J16
J12
J11
J10
J7 J9
J8
J4
J3
J2
J1
J5 J6
Locating connectors
CN15 CN18 CN17 CN19 CN16
CN14
CN13
CN12
CN9
CN11 CN3
CN10
CN7
CN8
CN5
CN4
CN2
CN1
CN6
4 PCM-5862/5862L Startup Manual
