OMV

Technical Information
Versions

VERSIONS

Main type designation

European version

Drain connection
Mounting flange

Check valve
US version
Port size
Shaft

Cyl. 50 mm G1 m Yes Yes OMV

Cyl. 2.25 in 1 5/16-12 UN m Yes Yes OMV
G1 m Yes Yes OMV
Standard Splined 2.125 in
1 5/16-12 UN m Yes Yes OMV
flange
Tapered 60 mm G1 m Yes Yes OMV
Tapered 2.25 in 1 5/16-12 UN m Yes Yes OMV
SAE-C Cyl. 2.25 in 1 5/16-12 UN m Yes Yes OMV
flange Splined 2.125 in 1 5/16-12 UN m Yes Yes OMV
Cyl. 50 mm G1 m Yes Yes OMVW
Wheel Tapered 60 mm G1 m Yes Yes OMVW
Tapered 2.25 in 1 5/16-12 UN m Yes Yes OMVW
Short No output shaft G1 m Yes Yes OMVS
Function diagram - see page : →

Features available (options) :

Speed sensor
Motor with tacho connection
Viton shaft seal
Painted
Ultra short

58 DKMH.PK.130.B4.02 520L0407 Rev. C 04.2004

 OMV
Technical Information
Code Numbers

CODE NUMBERS
Displacement [cm3]

Pageloads
Technical data – Page

Dimensions – Page
loads –shaft
CODE NUMBERS
NUMBER

Permissible
Shaft
315 400 500 630 800
151B 3100 3101 3102 3103 3104 60 63 72
151B 2150 2151 2152 2153 2154 60 63 73
151B 3105 3106 3107 3108 3109 60 63 72
151B 2155 2156 2157 2158 2159 60 63 73
151B 3110 3111 3112 3113 3114 60 63 72
151B 2160 2161 2162 2163 2164 60 63 73
151B 2183 2184 2185 2186 2187 60 64 74
151B 2188 2189 2190 2191 2192 60 64 74
151B 3115 3116 3117 3118 3119 60 63 75
151B 3120 3121 3122 3123 3124 60 63 75
151B 2170 2171 2172 2173 2174 60 63 76
151B 3125 3126 3127 3128 3129 60 – 77
65 65 66 66 67

Ordering
Add the four digit prefix “151B” to the four digit numbers from the chart for complete
code number.

Example:
151B3101 for an OMV 400 with standard flange, cyl. 50 mm shaft and port size G 1.

Note: Orders will not be accepted without the four digit prefix.

DKMH.PK.130.B4.02 520L0407 Rev. C 04.2004 59

 OMV
Technical Information
Technical data

TECHNICAL DATA FOR OMV, OMVW AND OMVS

Type OMV OMV OMV OMV OMV
OMVW OMVW OMVW OMVW OMVW
OMVS OMVS OMVS OMVS OMVS
Motor size 315 400 500 630 800
cm3 314.5 400.9 499.6 629.1 801.8
Geometric displacement
[in3] [19.19] [24.46] [30.49] [38.39] [48.93]
min-1 cont. 510 500 400 315 250
Max. speed
[rpm] int1) 630 600 480 380 300
920 1180 1460 1660 1880
cont.
Nm [8140] [10440] [12920] [14690] [16640]
Max. torque
[lbf·in] 1110 1410 1760 1940 2110
int.1)
[9820] [12480] [15580] [17170] [18680]
42.5 53.5 53.5 48.0 42.5
cont.
kW [57.0] [71.7] [71.7] [64.4] [57.0]
Max. output
[hp] 51.0 64.0 64.0 56.0 48.0
int.1)
[68.4] [85.8] [85.8] [75.1] [64.4]
200 200 200 180 160
cont.
[2900] [2900] [2900] [2610] [2320]
bar 240 240 240 210 180
Max. pressure drop int.1)
[psi] [3480] [3480] [3480] [3050] [2610]
280 280 280 240 210
peak2)
[4060] [4060] [4060] [3480] [3050]
160 200 200 200 200
cont.
l/min [42.3] [52.8] [52.8] [52.8] [52.8]
Max. oil flow
[USgal/min] 200 240 240 240 240
int.1)
[52.8] [63.4] [63.4] [63.4] [63.4]
Max. starting pressure bar 8 8 8 8 8
with unloaded shaft [psi] [116] [116] [116] [116] [116]
at max. press. drop cont. 710 910 1130 1330 1510
Min. starting Nm [lbf·in] [6280] [8050] [10000] [11770] [13360]
torque at max. press. drop int.1) 850 1090 1360 1550 1700
Nm [lbf·in] [7520] [9650] [12040] [13720] [15050]

Max. return pressure

Type Max. inlet pressure
with drain line
bar 210 140
cont.
[psi] [3050] [2030]
OMV
bar 250 175
OMVW int.1)
[psi] [3630] [2540]
OMVS
bar 300 210
peak2)
[psi] [4350] [3050]
1)
Intermittent operation: the permissible values may occur for max. 10% of every minute.
2)
Peak load: The permissible values may occur for max. 1% of every minute.

For max. permissible combination of flow and pressure, see function diagram for actual motor.

60 DKMH.PK.130.B4.02 520L0407 Rev. C 04.2004

 OMV
Technical Information
Technical data

MAX. PERMISSIBLE OMV with check valves OMV with check valves
SHAFT SEAL PRESSURE and without use of and with
drain connection: drain connection:
The pressure on the shaft seal The shaft seal pressure equals
never exceeds the pressure in the pressure on the drain line.
the return line

Max. return pressure without drain line or max. pressure in the drain line

– – – – Intermittent operation: the permissible values may occur for max. 10% of every minute.
Continuous operation

DKMH.PK.130.B4.02 520L0407 Rev. C 04.2004 61

 OMV
Technical Information
Technical data

PRESSURE DROP IN
MOTOR

The curve applies to an unloaded motor shaft and an oil viscosity of 35 mm2/s (165 SUS)

OIL FLOW IN DRAIN LINE The table shows the max. oil flow in the Pressure Viscosity Oil flow in
drain line at a return pressure less than drop drain line
5-10 bar [75-150 psi]. bar mm2/s l/min
[psi] [SUS] [US gal/min]
20 3.0
140 [100] [0.79]
[2030] 35 2.0
[165] [0.53]
20 6.0
210 [100] [1.59]
[3050] 35 4.0
[165] [1.06]

DIRECTION OF SHAFT
ROTATION

62 DKMH.PK.130.B4.02 520L0407 Rev. C 04.2004

 OMV
Technical Information
Technical data

PERMISSIBLE SHAFT Mounting flange: Shaft:

LOADS FOR OMV Standard All shaft types

Mounting flange: Shaft:

Wheel All shaft types

The output shaft runs in tapered roller bearings that permit high axial and radial forces.
The permissible radial load on the shaft is shown for an axial load of 0 N as a function of
the distance from the mounting flange to the point of load application.
The curve is based on B10 bearing life (2000 hours or 12,000,000 shaft revolutions at
100 min-1) at rated output torque, when mineral-based hydraulic oil with a sufficient
content of anti-wear additives, is used.
For 3,000,000 shaft revolutions or 500 hours – increase these shaft loads with 52%.
The dash curve shows max. radial shaft load. Any shaft load exceeding the values shown
in the curve will involve a risk of breakage.
Bearing life calculations can be made using the explanation and formula provided in
the chapter "Bearing dimensioning" in the technical information "General Orbital motors"
DHMH.PK.100.G2.02 520L0232.

DKMH.PK.130.B4.02 520L0407 Rev. C 04.2004 63

 OMV
Technical Information
Technical data

PERMISSIBLE SHAFT Mounting flange: Shaft:

LOADS FOR OMV SAE-C All shaft types

A: Cyl. 2.25 in shaft

B: Splined 2.125 in shaft

The output shaft runs in tapered roller bearings that permit high axial and radial forces.
The permissible radial load on the shaft is shown for an axial load of 0 N as a function of
the distance from the mounting flange to the point of load application.
The curve is based on B10 bearing life (2000 hours or 12,000,000 shaft revolutions at
100 min-1) at rated output torque, when mineral-based hydraulic oil with a sufficient
content of anti-wear additives, is used.
For 3,000,000 shaft revolutions or 500 hours – increase these shaft loads with 52%.
The dash curve shows max. radial shaft load. Any shaft load exceeding the values shown
in the curve will involve a risk of breakage.
Bearing life calculations can be made using the explanation and formula provided in
the chapter "Bearing dimensioning" in the technical information "General Orbital motors"
DHMH.PK.100.G2.02 520L0232.

64 DKMH.PK.130.B4.02 520L0407 Rev. C 04.2004

 OMV
Technical Information
Function diagrams

FUNCTION DIAGRAMS

Explanation of function diagram use, basis and conditions can be found on page 5.
n Continuous range
n Intermittent range (max. 10% operation every minute)
Note: Intermittent pressure drop and oil flow must not occur simultaneously.

DKMH.PK.130.B4.02 520L0407 Rev. C 04.2004 65

 OMV
Technical Information
Function diagrams

FUNCTION DIAGRAMS

Explanation of function diagram use, basis and conditions can be found on page 5.
n Continuous range
n Intermittent range (max. 10% operation every minute)
Note: Intermittent pressure drop and oil flow must not occur simultaneously.

66 DKMH.PK.130.B4.02 520L0407 Rev. C 04.2004

 OMV
Technical Information
Function diagrams

FUNCTION DIAGRAMS

Explanation of function diagram use, basis and conditions can be found on page 5.
n Continuous range
n Intermittent range (max. 10% operation every minute)
Note: Intermittent pressure drop and oil flow must not occur simultaneously.

DKMH.PK.130.B4.02 520L0407 Rev. C 04.2004 67

 OMV
Technical Information
Shaft version

SHAFT VERSION

A: Cylindrical 50 mm shaft
D: Parallel key
A14 × 9 × 70
DIN 6885
Keyway deviates from
standard

B: Cylindrical 2.25 in shaft

for OMV with standard
mounting flange
E: Parallel key
1
/2 × 1/2 × 21/4 in
B.S. 46
Keyway deviates from
standard

C: Cylindrical 2.25 in shaft

for OMV with mounting
flange SAE-C
F: Parallel key
1
/2 × 1/2 × 21/4 in
B.S. 46
Keyway deviates from
standard

68 DKMH.PK.130.B4.02 520L0407 Rev. C 04.2004

 OMV
Technical Information
Shaft version

SHAFT VERSION

D: Involute splined shaft

ANS B92.1 - 1970 standard
Flat root side fit
Pitch 8/16
Teeth 16
Major dia. 2.125 in
Pressure angle 30°

US Version
E: Involute splined shaft
for OMV with standard
mounting flange
ANS B92.1 - 1970 standard
Flat root side fit
Pitch 8/16
Teeth 16
Major dia. 2.125 in
Pressure angle 30°

US Version
F: Involute splined shaft
for OMV with mounting
flange SAE-C
ANS B92.1 - 1970 standard
Flat root side fit
Pitch 8/16
Teeth 16
Major dia. 2.125 in
Pressure angle 30°

DKMH.PK.130.B4.02 520L0407 Rev. C 04.2004 69

 OMV
Technical Information
Shaft version

SHAFT VERSION

G: Tapered 60 mm shaft
(ISO/R775)
J: DIN 937
Across flats: 65 mm
Tightening torque:
750 ±50 Nm [6640 ±440 lbf·in]
I: Taper 1:10
K: Parallel key
B16 × 10 × 32
DIN 6885
Keyway deviates from
standard

H: Tapered 2.25 in shaft

L: Cone 1:8
SAE J501
M: 11/2 - 18 UNEF
Across flats: 23/8 in
Tightening torque:
750 ±50 Nm [6640 ±440 lbf·in]
N: Parallel key
9
/16 × 9/16 × 2 in
B.S. 46
Keyway deviates from
standard

70 DKMH.PK.130.B4.02 520L0407 Rev. C 04.2004

 OMV
Technical Information
Technical data

PORT THREAD VERSIONS

A: G main ports B: UN main ports

E: ISO 228/1 - G1 F: 1 5/16 - 12 UN
O-ring boss port

C: G drain port D: UNF drain port

G: ISO 228/1 - G1/4 H: 9/16 - 18 UNF
O-ring boss port

DKMH.PK.130.B4.02 520L0407 Rev. C 04.2004 71

 OMV
Technical Information
Dimensions – European version

STANDARD FLANGE

Lmax. L1* L2 L3
Type mm mm mm Output shaft mm
[in] [in] [in] [in]
215 22.0 160 Cyl. 50 mm 82
OMV 315
[8.46] [0.866] [6.30] Splined 2.125 in [3.23]
222 29.0 167 105
OMV 400 Tapered 60 mm
[8.74] [1.142] [6.57] [4.13]
230 37.0 175 C: Drain connection
OMV 500
[9.05] [1.457] [6.89] G 1⁄4; 12 mm [0.47 in] deep
240 47.5 186 D: M12; 12 mm [0.47 in] deep
OMV 630 E: G 1; 18 mm [0.71 in] deep
[9.45] [1.870] [7.32]
254 61.5 200
OMV 800
[10.00] [2.421] [7.87]
*) The gearwheel set is 3.5 mm
[0.138 in] wider across the
rollers than the L1 dimensions

72 DKMH.PK.130.B4.02 520L0407 Rev. C 04.2004

 OMV
Technical Information
Dimensions – US version

STANDARD FLANGE

Lmax. L1* L2 L3
Type mm mm mm Output shaft mm
[in] [in] [in] [in]
215 22.0 160 Cyl. 2.25 in 82
OMV 315
[8.46] [0.866] [6.30] Splined 2.125 in [3.23]
222 29.0 167 100
OMV 400 Tapered 2.25 in
[8.74] [1.142] [6.57] [3.94]
230 37.0 175 C: Drain connection
OMV 500
[9.05] [1.457] [6.89] 9
⁄16 - 18 UNF;
240 47.5 186 13 mm [0.51 in] deep
OMV 630 O-ring boss port
[9.45] [1.870] [7.32] D: 1 5⁄16 - 12 UN;
254 61.5 200 19 mm [0.75 in] deep
OMV 800 O-ring boss port
[10.00] [2.421] [7.87]
*) The gearwheel set is 3.5 mm
[0.138 in] wider across the
rollers than the L1 dimensions

DKMH.PK.130.B4.02 520L0407 Rev. C 04.2004 73

 OMV
Technical Information
Dimensions – US version

SAE-C FLANGE

Lmax. L1* L2 L3
Type mm mm mm Output shaft mm
[in] [in] [in] [in]
239 22.0 185 99
OMV 315 Cyl. 2.25 in
[9.41] [0.866] [7.28] [3.90]
246 29.0 192 76.7
OMV 400 Splined 2.125 in
[9.69] [1.142] [7.56] [3.02]
254 37.0 200 C: Drain connection
OMV 500
[10.00] [1.457] [7.87] 9
⁄16 - 18 UNF;
265 47.5 211 13 mm [0.51 in] deep
OMV 630 O-ring boss port
[10.43] [1.870] [8.31] D: 1 5⁄16 - 12 UN;
279 61.5 225 19 mm [0.75 in] deep
OMV 800 O-ring boss port
[10.98] [2.421] [8.86]
*) The gearwheel set is 3.5 mm
[0.138 in] wider across the
rollers than the L1 dimensions

74 DKMH.PK.130.B4.02 520L0407 Rev. C 04.2004

 OMV
Technical Information
Dimensions – European version

WHEEL

Lmax. L1* L2 L3
Type mm mm mm Output shaft mm
[in] [in] [in] [in]
OMVW 146 22.0 92 82
Cyl. 50 mm
315 [5.75] [0.866] [3.62] [3.23]
OMVW 153 29.0 99 105
Tapered 60 mm
400 [6.02] [1.142] [3.90] [4.13]
OMVW 161 37.0 107 C: Drain connection
500 [6.34] [1.457] [4.21] G 1⁄4; 12 mm [0.47 in] deep
OMVW 172 47.5 118 D: M12; 12 mm [0.47 in] deep
E: G 1; 18 mm [0.71 in] deep
630 [6.77] [1.870] [4.65]
OMVW 185 61.5 132
800 [7.28] [2.421] [5.20]
*) The gearwheel set is 3.5 mm
[0.138 in] wider across the
rollers than the L1 dimensions

DKMH.PK.130.B4.02 520L0407 Rev. C 04.2004 75

 OMV
Technical Information
Dimensions – US version

WHEEL

Lmax. L1* L2
Type mm mm mm
[in] [in] [in]
OMVW 147 22.0 92
315 [5.79] [0.866] [3.62]
C: Drain connection
OMVW 154 29.0 99 9
⁄16 - 18 UNF;
400 [6.06] [1.142] [3.90] 13 mm [0.51 in] deep
OMVW 162 37.0 107 O-ring boss port
D: 1 5⁄16 - 12 UN;
500 [6.38] [1.457] [4.21] 19 mm [0.75 in] deep
OMVW 172 47.5 118 O-ring boss port
630 [6.77] [1.870] [4.65]
*) The gearwheel set is 3.5 mm
OMVW 187 61.5 132 [0.138 in] wider across the
800 [7.36] [2.421] [5.20] rollers than the L1 dimensions

76 DKMH.PK.130.B4.02 520L0407 Rev. C 04.2004

 OMV
Technical Information
Dimensions – European version

SHORT

Lmax. L1* L2
Type mm mm mm
[in] [in] [in]
OMVS 171 22.0 117
315 [6.73] [0.866] [4.61]
OMVS 179 29.0 124 C: Drain connection
400 [7.05] [1.142] [4.88] G 1⁄4; 12 mm [0.47 in] deep
D: M12; 12 mm [0.47 in] deep
OMVS 186 37.0 132 E: G 1; 18 mm [0.71 in] deep
500 [7.32] [1.457] [5.20]
OMVS 197 47.5 143
630 [7.76] [1.870] [5.63]
*) The gearwheel set is 3.5 mm
OMVS 211 61.5 157 [0.138 in] wider across the
800 [8.31] [2.421] [6.18] rollers than the L1 dimensions

DKMH.PK.130.B4.02 520L0407 Rev. C 04.2004 77

 OMV
Technical Information
OMVS

INSTALLING THE OMVS The cardan shaft of the OMVS motor acts as an “output shaft”. Because of the movement
of the shaft, no seal can be fitted at the shaft output.
Internal oil leakage from the motor will therefore flow into the attached component.

During start and operation it is important that the spline connection and the bearings
in the attached component receive oil and are adequately lubricated. To ensure that the
spline connection receives sufficient oil, a conical sealing ring between the shaft of the
attached component and the motor intermediate plate is recommended. This method
is used in the OMV.

The conical sealing ring (code. no. 633B9021) is supplied with the motor.

To ensure that oil runs to the bearings and other parts of the attached component, the
stop plate must have a hole in it (see fig. below).

We recommend an O-ring between motor and attached component. The O-ring

(code no. 151B1041) is supplied with the motor. If motor and attached component have
been separated, remember to refill before starting up. Fill the oil through the drain
connection.

OMVS
DIMENSIONS OF THE
ATTACHED COMPONENT

A: O-ring: 140 × 3 mm E: Internal drain channel

B: External drain channel F: M12; min. 18 mm [0.71 in] deep
C: Drain connection G: Oil circulation hole
G 1⁄4; 12 mm [0.47 in] deep H: Hardened stop plate
D: Conical seal ring

78 DKMH.PK.130.B4.02 520L0407 Rev. C 04.2004

 OMV
Technical Information
OMVS

INTERNAL SPLINE DATA The attached component must have internal splines corresponding to the external
FOR THE COMPONENT TO splines on the motor cardan shaft (see drawing below).
BE ATTACHED
Material:
Case hardening steel with a tensile strength corresponding at least to 20 MoCr4
(900 N/mm2) or SAE 8620.

Hardening specification:
• On the surface: HV = 750 ± 50
• 0.7 ± 0.2 mm under the surface: HV = 560

Internal involute spline data

Standard ANS B92.1-1970, class 5 (corrected m · X = 1; m = 2.54)

Flat root
mm in
side fit
Number of
z 16 16
teeth
Pitch DP 10/20 10/20
Pressure angle 30° 30°
Pitch dia. D 40.640 1.6
Major dia. Dri 45.2 0+0.4 1.780 0+0.016
Form dia.
Dfi 44.6 1.756
(min.)

Minor dia. Di 38.5 0+ 0.039 1.516 0+ 0.0015

Space width
Lo 5.180 ±0.037 0.204 ±0 .0015
(circular)
Tooth
thickness So 2.835 0.1116
(circular)
Fillet radius Rmin. 0.4 0.015
Max.
measurement l 32.47 0+ 0.15 1.278 0+0.006
between pins*
Pin dia. d 5.6 ±0.001 0.22 ±0.00004
* Finished dimensions (when hardened)

DRAIN CONNECTION ON A drain line ought to be used when pressure in the return line can exceed the permissible
OMVS OR ATTACHED pressure on the shaft seal of the attached component.
COMPONENT
The drain line can be connected at two different points:
1) at the motor drain connection
2) at the drain connection of the attached component.
If a drain line is fitted to the attached component, it must be possible for oil to flow freely
between motor and attached component.

The drain line must be led to the tank in such a way that there is no risk of the motor and
attached component being drained of oil when at rest.
The maximum pressure in the drain line is limited by the attached component and its
shaft seal.

DKMH.PK.130.B4.02 520L0407 Rev. C 04.2004 79

 OMS, OMT and OMV
Technical Information
Weight of motors

WEIGHT OF MOTORS Weight Weight Weight

Code no Code no Code no
kg [lb] kg [lb] kg [lb]
151B2050 20.0 44.1 151B2188 30.0 66.2 151B3102 33.5 73.9
151B2051 20.5 45.2 151B2189 30.8 67.9 151B3103 34.9 76.9
151B2052 21.0 46.3 151B2190 31.7 69.9 151B3104 36.5 80.5
151B2053 22.0 48.5 151B2191 33.1 73.0 151B3105 31.8 70.1
151B2054 23.0 50.7 151B2192 34.7 76.5 151B3106 32.6 71.9
151B2055 24.0 52.9 151B3000 20.0 44.1 151B3107 33.5 73.9
151B2056 20.0 44.1 151B3001 20.5 45.2 151B3108 34.9 76.9
151B2057 20.5 45.2 151B3002 21.0 46.3 151B3109 36.5 80.5
151B2058 21.0 46.3 151B3003 22.0 48.5 151B3110 31.8 70.1
151B2059 22.0 48.5 151B3004 23.0 50.7 151B3111 32.6 71.9
151B2060 23.0 50.7 151B3005 24.0 52.9 151B3112 33.5 73.9
151B2061 24.0 52.9 151B3006 20.0 44.1 151B3113 34.9 76.9
151B2062 20.0 44.1 151B3007 20.5 45.2 151B3114 36.5 80.5
151B2063 20.5 45.2 151B3008 21.0 46.3 151B3115 32.4 71.4
151B2064 21.0 46.3 151B3009 22.0 48.5 151B3116 33.2 73.2
151B2065 22.0 48.5 151B3010 23.0 50.7 151B3117 34.1 75.2
151B2066 23.0 50.7 151B3011 24.0 52.9 151B3118 35.5 78.3
151B2067 24.0 52.9 151B3012 20.0 44.1 151B3119 37.1 81.8
151B2080 22.0 48.5 151B3013 20.5 45.2 151B3120 32.4 71.4
151B2081 22.5 49.6 151B3014 21.0 46.3 151B3121 33.2 73.2
151B2082 23.0 50.7 151B3015 22.0 48.5 151B3122 34.1 75.2
151B2083 24.0 52.9 151B3016 23.0 50.7 151B3123 35.5 78.3
151B2084 25.0 55.1 151B3017 24.0 52.9 151B3124 37.1 81.8
151B2085 26.0 57.3 151B3018 20.0 44.1 151B3125 22.7 50.1
151B2150 31.8 70.1 151B3019 20.5 45.2 151B3126 23.5 51.8
151B2151 32.6 71.9 151B3020 21.0 46.3 151B3127 24.4 53.8
151B2152 33.5 73.9 151B3021 22.0 48.5 151B3128 25.6 56.4
151B2153 34.9 76.9 151B3022 23.0 50.7 151B3129 27.7 61.1
151B2154 36.5 80.5 151B3023 24.0 52.9 151B3200 31.0 68.3
151B2155 31.8 70.1 151B3024 22.0 48.5 151B3201 31.5 69.4
151B2156 32.6 71.9 151B3025 22.5 49.6 151B3202 32.0 70.5
151B2157 33.5 73.9 151B3026 23.0 50.7 151B3203 33.0 72.8
151B2158 34.9 76.9 151B3027 24.0 52.9 151B3204 34.0 75.0
151B2159 36.5 80.5 151B3028 25.0 55.1 151B3205 35.0 77.2
151B2160 31.8 70.1 151B3029 26.0 57.3 151B3207 31.0 68.3
151B2161 32.6 71.9 151B3030 22.0 48.5 151B3208 31.5 69.4
151B2162 33.5 73.9 151B3031 22.5 49.6 151B3209 32.0 70.5
151B2163 34.9 76.9 151B3032 23.0 50.7 151B3210 33.0 72.8
151B2164 36.5 80.5 151B3033 24.0 52.9 151B3211 34.0 75.0
151B2170 32.4 71.4 151B3034 25.0 55.1 151B3212 35.0 77.2
151B2171 33.2 73.2 151B3035 26.0 57.3 151B4000 24.5 54.0
151B2172 34.1 75.2 151B3036 15.0 33.1 151B4001 25.0 55.1
151B2173 35.5 78.3 151B3037 15.5 34.2 151B4002 25.5 56.2
151B2174 37.1 81.8 151B3038 16.0 35.3 151B4003 26.5 58.4
151B2183 30.0 66.2 151B3039 17.0 37.5 151B4004 27.5 60.6
151B2184 30.8 67.9 151B3040 18.0 39.7 151B4005 28.5 62.8
151B2185 31.7 69.9 151B3041 19.0 41.9 151B4007 24.5 54.0
151B2186 33.1 73.0 151B3100 31.8 70.1 151B4008 25.0 55.1
151B2187 34.7 76.5 151B3101 32.6 71.9 151B4009 25.5 56.2

80 DKMH.PK.130.B4.02 520L0407 Rev. C 04.2004

 OMS, OMT and OMV
Technical Information
Weight of motors

WEIGHT OF MOTORS Weight Weight Weight

Code no Code no Code no
kg [lb] kg [lb] kg [lb]
151B4010 26.5 58.4 151F0534 12.8 28.2 151F2237 10.8 23.8
151B4011 27.5 60.6 151F0535 7.8 17.2 151F2238 11.2 24.7
151B4012 28.5 62.8 151F0536 8.0 17.6 151F2239 11.6 25.6
151B4021 24.5 54.0 151F0537 8.3 18.3 151F2240 12.1 26.7
151B4022 25.0 55.1 151F0538 8.7 19.2 151F2241 12.8 28.2
151B4023 25.5 56.2 151F0539 9.1 20.1 151F2242 10.3 22.7
151B4024 26.5 58.4 151F0540 9.6 21.2 151F2243 10.5 23.1
151B4025 27.5 60.6 151F0541 10.3 22.7 151F2244 10.8 23.8
151B4026 28.5 62.8 151F0542 10.2 22.5 151F2245 11.2 24.7
151B4028 24.5 54.0 151F0543 10.4 22.9 151F2246 11.6 25.6
151B4029 25.0 55.1 151F0544 10.7 23.6 151F2247 12.1 26.7
151B4030 25.5 56.2 151F0545 11.1 24.5 151F2248 12.8 28.2
151B4031 26.5 58.4 151F0546 11.5 25.4 151F2261 13.1 28.9
151B4032 27.5 60.6 151F0547 12.0 26.5 151F2262 13.1 28.9
151B4033 28.5 62.8 151F0548 12.7 28.0 151F2263 13.6 30.0
151F0500 9.8 21.6 151F0560 9.8 21.6 151F2264 13.1 28.9
151F0501 10.0 22.1 151F0561 10.0 22.1 151F2265 13.6 30.0
151F0502 10.3 22.7 151F0562 10.3 22.7 151F2300 9.8 21.6
151F0503 10.7 23.6 151F0563 10.7 23.6 151F2301 10.0 22.1
151F0504 11.1 24.5 151F0564 11.1 24.5 151F2302 10.3 22.7
151F0505 11.6 25.6 151F0565 11.6 25.6 151F2303 10.7 23.6
151F0506 12.3 27.1 151F0566 12.3 27.1 151F2304 11.1 24.5
151F0507 9.8 21.6 151F0605 13.1 28.9 151F2305 11.6 25.6
151F0508 10.0 22.1 151F0608 11.1 24.5 151F2306 12.3 27.1
151F0509 10.3 22.7 151F0609 13.6 30.0 151F2307 13.1 28.9
151F0510 10.7 23.6 151F0610 13.6 30.0 151F2308 9.8 21.6
151F0511 11.1 24.5 151F2200 9.8 21.6 151F2309 10.0 22.1
151F0512 11.6 25.6 151F2201 10.0 22.1 151F2310 10.3 22.7
151F0513 12.3 27.1 151F2202 10.3 22.7 151F2311 10.7 23.6
151F0514 9.8 21.6 151F2203 10.7 23.6 151F2312 11.1 24.5
151F0515 10.0 22.1 151F2204 11.1 24.5 151F2313 11.6 25.6
151F0516 10.3 22.7 151F2205 11.6 25.6 151F2314 12.3 27.1
151F0517 10.7 23.6 151F2206 12.3 27.1 151F2315 13.1 28.9
151F0518 11.1 24.5 151F2207 9.8 21.6 151F2316 9.8 21.6
151F0519 11.6 25.6 151F2208 10.0 22.1 151F2317 10.0 22.1
151F0520 12.3 27.1 151F2209 10.3 22.7 151F2318 10.3 22.7
151F0521 10.3 22.7 151F2210 10.7 23.6 151F2319 10.7 23.6
151F0522 10.5 23.1 151F2211 11.1 24.5 151F2320 11.1 24.5
151F0523 10.8 23.8 151F2212 11.6 25.6 151F2321 11.6 25.6
151F0524 11.2 24.7 151F2213 12.3 27.1 151F2322 12.3 27.1
151F0525 11.6 25.6 151F2214 9.8 21.6 151F2323 13.1 28.9
151F0526 12.1 26.7 151F2215 10.0 22.1 151F2324 9.8 21.6
151F0527 12.8 28.2 151F2216 10.3 22.7 151F2325 10.0 22.1
151F0528 10.3 22.7 151F2217 10.7 23.6 151F2326 10.3 22.7
151F0529 10.5 23.1 151F2218 11.1 24.5 151F2327 10.7 23.6
151F0530 10.8 23.8 151F2219 11.6 25.6 151F2328 11.1 24.5
151F0531 11.2 24.7 151F2220 12.3 27.1 151F2329 11.6 25.6
151F0532 11.6 25.6 151F2235 10.3 22.7 151F2330 12.3 27.1
151F0533 12.1 26.7 151F2236 10.5 23.1 151F2331 13.1 28.9

DKMH.PK.130.B4.02 520L0407 Rev. C 04.2004 81

 OMS, OMT and OMV
Technical Information
Weight of motors

WEIGHT OF MOTORS Weight Weight Weight

Code no Code no Code no
kg [lb] kg [lb] kg [lb]
151F2332 9.8 21.6 151F2355 11.6 25.6 151F2373 11.6 25.6
151F2333 10.0 22.1 151F2356 12.3 27.1 151F2374 12.3 27.1
151F2334 10.3 22.7 151F2357 13.1 28.9 151F2375 13.1 28.9
151F2335 10.7 23.6 151F2358 14.0 30.9 151F2376 14.0 30.9
151F2336 11.1 24.5 151F2359 9.8 21.6 151F2395 9.8 21.6
151F2337 11.6 25.6 151F2360 10.0 22.1 151F2396 10.0 22.1
151F2338 12.3 27.1 151F2361 10.3 22.7 151F2397 10.3 22.7
151F2339 13.1 28.9 151F2362 10.7 23.6 151F2398 10.7 23.6
151F2345 14.0 30.9 151F2363 11.1 24.5 151F2399 11.1 24.5
151F2346 14.0 30.9 151F2364 11.6 25.6 151F2400 11.6 25.6
151F2347 14.0 30.9 151F2365 12.3 27.1 151F2401 12.3 27.1
151F2348 14.0 30.9 151F2366 13.1 28.9 151F2402 13.1 28.9
151F2349 14.0 30.9 151F2367 14.0 30.9 151F2403 14.0 30.9
151F2350 9.8 21.6 151F2368 9.8 21.6 151F2413 9.8 21.6
151F2351 10.0 22.1 151F2369 10.0 22.1 151F2414 10.0 22.1
151F2352 10.3 22.7 151F2370 10.3 22.7 151F2415 10.3 22.7
151F2353 10.7 23.6 151F2371 10.7 23.6 151F2416 10.7 23.6
151F2354 11.1 24.5 151F2372 11.1 24.5 151F2417 11.1 24.5

82 DKMH.PK.130.B4.02 520L0407 Rev. C 04.2004

 OMS, OMT and OMV
Technical Information
Notes

NOTES

DKMH.PK.130.B4.02 520L0407 Rev. C 04.2004 83

OUR PRODUCTS Sauer-Danfoss Hydraulic Power Systems
– Market Leaders Worldwide
Hydrostatic transmissions
Sauer-Danfoss is a comprehensive supplier providing complete
Hydraulic power steering systems to the global mobile market.
Electro hydraulic power steering
Sauer-Danfoss serves markets such as agriculture, construction, road
Electric power steering building, material handling, municipal, forestry, turf care, and many
others.
Closed and open circuit axial piston
pumps and motors We offer our customers optimum solutions for their needs and
develop new products and systems in close cooperation and
Gear pumps and motors
partnership with them.
Bent axis motors
Sauer-Danfoss specializes in integrating a full range of system
Orbital motors components to provide vehicle designers with the most advanced
total system design.
Transit mixer drives

Planetary compact gears Sauer-Danfoss provides comprehensive worldwide service for its
products through an extensive network of Authorized Service
Proportional valves Centers strategically located in all parts of the world.

Directional spool valves

Cartridge valves

Hydraulic integrated circuits

Hydrostatic transaxles

Integrated systems

Fan drive systems

Sauer-Danfoss (US) Company
Electrohydraulic controls 2800 East 13th Street
Ames, IA 50010, USA
Digital electronics and software Phone: +1 515 239-6000, Fax: +1 515 239-6618
Electric motors and inverters
Sauer-Danfoss (Neumünster) GmbH & Co. OHG
Sensors Postfach 2460, D-24531 Neumünster
Krokamp 35, D-24539 Neumünster, Germany
Phone: +49 4321 871-0, Fax: +49 4321 871-122

Sauer-Danfoss (Nordborg) A/S

DK-6430 Nordborg, Denmark
Phone: +45 7488 4444, Fax: +45 7488 4400

DKMH.PK.130.B4.02 520L0407 Rev. C 04.2004 www.sauer-danfoss.com