MENCK MHU HYDRAULIC HAMMER DATA SHEET- Rev.

I (15/05/2007)

Menck Menck Menck Menck Menck

HAMMER TYPE: HYDRAULIC (Above & Below Water)
MHU 195 MHU 220 MHU 600I MHU 600B MHU 800S
OPERATING DATA Unit
Max. Rated Energy (GRLWeap database) kNm 191.41 215.76 588.171 619.899 800
Min. Rated Energy kNm 65 75 200 25 80
Blow Rate at max. energy possible bl/min 36 36 42 38 38
Weight of Ram (GRLWeap database) kN 98.122 111.828 343.362 293.513 444.692
Maximum Stroke m 1.951 1.929 1.713 2.112 1.799
Hammer Efficiency (Continuous mode) % 95 95 95 95 95
Hammer Efficiency (At Restart or Full Set-up) % 85 85 85 85 85
552446-
Company Number Az. 764318 550552 764581 Coming
553374
WEIGHT DATA
Helmet (GRLWeap database) kN 19.6 40.03 97.86 97.86 145.188
Sleeve kN 110 136 177 114.8 172.656
Underwater Ballast (UW-Ballast) kN 55 55 206.01 98.1 255.06
Weight in Air with UW-Ballast kN 440 440 1205 892.71 1353.78
C.o.G. measured from top of Pile m 0.495 0.495 2.059 2.529 2.784 (Ass.)
Weight in Air without UW-Ballast kN 386.02 386.02 997.68 794.61 1098.72
C.o.G. measured from top of Pile m 1.055 1.055 2.250 3.4 (Ass.) 3.823
Weight in Water with UW-Ballast kN 382.59 382.59 997.27 716.1 1128.15
C.o.G. measured from top of Pile m 1.06 1.06 2.250 2.452 2.684
DIMENSIONAL DATA
Sleeve Length (From Anvil up to Bottom incl. UW-Ballast) m 3.4 (3.9) 3.4 (3.9) 3.2 (4.7) 3.596 3.825
Min. Sleeve overall dimension (without UW-Ballast) m ~1.75 ~1.75 ~2.4 ~3.44 ~3.85
Hammer length incl. pile sleeve and UW-Ballast m 11.9 11.9 16.4 15.6 17.1
Hammer length incl. pile sleeve and without UW-Ballast m 11.4 11.4 15.0 15.6 17.1
HAMMER DATA vs. PILE
Pile sleeve suitable for piles O.D. up to in 42 42 60 72 ( 84) 84
Standard Anvil suitable for piles up to in 1842 1842 3660 3672 4884
Max. Batter Pile Deg NA NA NA NA NA
Legend: NA= Not Available; GRLWeap = Driveability Software-Name; Ass.= Assumed; C.o.G.= Centre of Gravity.

1 of 13
 MENCK MHU HYDRAULIC HAMMER DATA SHEET- Rev. I (15/05/2007)

MENCK MENCK MENCK

HAMMER TYPE: HYDRAULIC (Above & Below Water)
MHU 1000 MHU 1700 MHU 3000
OPERATING DATA Unit
Max. Rated Energy (GRLWeap database) kNm 1000 1666.8 2945.54
Min. Rated Energy kNm 350 600 1000
Blow Rate at max. energy possible bl/min 30 30 30
Weight of Ram (GRLWeap database) kN 565.017 922.173 1618.73
Maximum Stroke m 1.77 1.807 1.82
Hammer Efficiency (Continuous mode) % 95 95 95
Hammer Efficiency (At Restart or Full Set-up) % 85 85 85
550553-
Company Number Az. 550558 550557 550556/550555
4/764579
WEIGHT DATA
Helmet (GRLWeap database) kN 306.93 306.93 275.79 431.48
Sleeve kN 545.436 832.378 792.648 1087.93
Underwater Ballast (UW-Ballast) kN 167.5 393.7 167.5 393.7 551.32 735.75 1109.5
Weight in Air with UW-Ballast kN 2137 2363 2424 2650 3409 5258 5632
C.o.G. measured from top of Pile m 1.515 0.875 1.410 0.754 1.650 3.120 2.402
Weight in Air without UW-Ballast kN 1969.5 2256.4 2857.65 4522.41
C.o.G. measured from top of Pile m 2.059 1.949 3.03 4.602
2046 2220
Weight in Water with UW-Ballast (Partially air-filled) kN 1804 1980 2942.6 4606.7 4706.7
(Ass.) (Ass.)
1.916 2.079
C.o.G. measured from top of Pile m 2.059 1.855 3.03 4.602 4.702
(Ass.) (Ass.)
DIMENSIONAL DATA
4.918 4.918 4.750 4.750 5.15 5.34 5.34
Sleeve Length (From Anvil up to Bottom incl. UW-Ballast) m
(5.326) (5.953) (5.158) (5.785) (6.51) (7.2) (8.52)
Min. Sleeve overall dimension (without UW-Ballast) m ~3.4 ~3.2 ~3.85 ~3.85
Hammer length incl. pile sleeve and UW-Ballast m 16.2 16.8 16.2 16.8 20.5 25.1 26.4
Hammer length incl. pile sleeve and without UW-Ballast m 15.8 15.8 15.8 ~23
HAMMER DATA vs. PILE
Pile sleeve suitable for piles O.D. up to in 84 84 102 102
Standard Anvil suitable for piles up to in 6084 5684 48102 60102
Max. Batter Pile Deg NA NA NA NA
Legend: NA= Not Available; GRLWeap = Driveability Software-Name; Ass.= Assumed; C.o.G.= Centre of Gravity.

2 of 13
 MENCK MHU HYDRAULIC HAMMER DATA SHEET- Rev. I (15/05/2007)

MENCK MENCK MENCK MENCK MENCK

HAMMER TYPE: HYDRAULIC (Above & Below Water)
MHU 200T MHU 270T MHU 400T MHU 500T MHU 600T
OPERATING DATA Unit
Max. Rated Energy Above Water kNm 230 300 439.955 550 659.87
Max. Rated Energy at 1000m Water Depth kNm 200 270 400 500 600
Min. Rated Energy kNm 20 30 40 50 60
Blow Rate at max. energy possible bl/min 38 40 55 38 38
Weight of Ram kN 119.682 158.995 233.398 296.262 357.747
Maximum Stroke m 1.849 1.887 1.885 1.874 1.845
Hammer Efficiency (Continuous mode) % 95 95 95 95 95
Hammer Efficiency (At Restart or Full Set-up) % 85 85 85 85 85
Company Number Az. To rent To rent To rent To rent 621480
WEIGHT DATA 36-72 60-86 48-86
Helmet kN 67.7 67.3 97.86 107 120 120 97.86
Sleeve kN 61.803 74.556 107.91 99 146 123 74.556
Underwater Ballast (UW-Ballast) kN 59.841 68.67 68.67 119 100 100 168.732
Weight in Air with UW-Ballast kN 439.488 513.063 725.94 856.4 897.6 874 974.133
C.o.G. measured from top of Pile m 1.642 1.970 1.50 2.644 2.529 2.534 2.855
Weight in Air without UW-Ballast kN 378.666 444.4 568.98 737.7 797.6 774 805.401
C.o.G. measured from top of Pile m 2.0 2.520 2.60 3.426 3.333 3.344 3.14
Weight in Water with UW-Ballast (Partially air-filled) kN 346.293 407.115 608.22 691.6 711.2 724 805.401
C.o.G. measured from top of Pile m 1.928 1.873 1.60 2.535 2.452 2.457 3.14
DIMENSIONAL DATA
Sleeve Length (From Anvil up to Bottom incl. UW-Ballast) m 2.770 2.770 3.5 3.538 3.596 3.556 3.2
Min. Sleeve overall dimension (without UW-Ballast) m ~2.4 ~2.4 NA 3.17 3.43 3.84 ~2.44
Hammer length incl. sleeve with and without UW-Ballast m 11.3 12.4 14.4 15.5 15.67 15.63 15
HAMMER DATA vs. PILE
60 (72)*
Pile sleeve suitable for piles O.D. up to in 62 62 *configuration has 36-72 60-86 48-86 60
different weight

Standard Anvil suitable for piles up to in 2062 2062 3660 36-72 60-86 48-86 3660
Max. Batter Pile Deg NA NA NA NA NA
Legend: NA= Not Available; GRLWeap = Driveability Software-Name; Ass.= Assumed; C.o.G.= Centre of Gravity.

3 of 13
 MENCK MRBS STEAM HAMMER DATA SHEET- Rev. I (15/05/2007)

MENCK MENCK MENCK MENCK MENCK

HAMMER TYPE: STEAM (Only Above Water)
MRBS1800 MRBS2500 MRBS2500S MRBS3000 MRBS4600
OPERATING DATA Unit
Max. Rated Energy (GRLWeap database) kNm 257.39 355.43 362.5 (355.43) 441.305 676.56
Min. Rated Energy (Menck Brochure) kNm 65.239 NA NA 111.82 171.48
Blow Rate at max. Stroke bl/min 40 40 40 40 36
Falling Weight (GRLWeap database) kN 171.681 284.488 284.488 294.278 451.275
Maximum Stroke (*Equivalent Stroke) m 1.5 1.25 1.25 (1.274*) 1.5 1.5
Minimum Stroke m 0.38 NA NA 0.38 0.38
Hammer Efficiency (Continuous mode) % 67 67 67 67 67
Hammer Efficiency (At Restart or Full Set-up) % 60 60 60 60 60
Company Number Az. 525474 710944 To rent 851754 552472/551949
WEIGHT DATA
Helmet (GRLWeap database) kN 100.08 111.21 152.13 154.8 265.11
Offshore Guide Cage kN 175 NA NA 239 NA
Weight in Air kN 667 932 932 902 1412
C.o.G. measured from top of Pile m 4.180 4.180 4.180 4.180 4.180
DIMENSIONAL DATA
Guide Cage Length (From Anvil up to Bottom) m 2.5 3.0 3.0 3.0 3.0
Min. Guide Cage overall dimension m ~2.75 ~3.5 ~3.5 ~3.5 ~4.0
Max. Hammer length incl. Guide Cage m 13.7 15.6 15.6 15.7 17.6
CUSHION DATA
Type (Wood) - Bongossi Bongossi Bongossi Bongossi Bongossi
Elastic Modulus MPa 2000 2000 2000 2000 2000
Area ( Diameter = (Area*4/)1/2 ) cm 8654 8654 8654 8654 19596
Thickness mm 200 200 200 200 250
Restitution Coefficient - 0.75 0.75 0.75 0.75 0.75
HAMMER DATA vs. PILE
Pile sleeve suitable for piles O.D. up to in 54 54 54 48 (62) 72 (84)
Standard Anvil suitable for piles up to in 3054 3054 3054 3048 & 3062 4272 & 4284
Max. Batter Pile Deg NA NA NA NA NA
Legend: NA= Not Available; GRLWeap = Driveability Software-Name; Ass.= Assumed; C.o.G.= Centre of Gravity.

4 of 13
 MENCK MRBS STEAM HAMMER DATA SHEET- Rev. I (15/05/2007)

MENCK MENCK MENCK MENCK

HAMMER TYPE: STEAM (Only Above Water)
MRBS4600S MRBS5000 MRBS5000S MRBS8000
OPERATING DATA Unit
Max. Rated Energy (GRLWeap database) kNm 800 (676.56) 735.4 900 (735.4) 1176.66
Min. Rated Energy (Menck Brochure) kNm 171.48 186.4 186.4 298.24
Blow Rate at max. Stroke bl/min 36 40 40 36
Falling Weight (GRLWeap database) kN 451.275 490.523 490.523 784.846
Maximum Stroke (*Equivalent Stroke) m 1.5 (1.773*) 1.5 1.5 (1.835*) 1.5
Minimum Stroke m 0.38 0.38 0.38 0.38
Hammer Efficiency (Continuous mode) % 67 67 67 67
Hammer Efficiency (At Restart or Full Set-up) % 60 60 60 60
Company Number Az. To rent To rent 717471/551948 To rent
WEIGHT DATA
Helmet (GRLWeap database) kN 265.11 294.03 294.03 415.46
Offshore Guide Cage kN NA 353.16 353.16 833.85
Weight in Air kN 1412 1589 1589 2717
C.o.G. measured from top of Pile m 4.180 4.180 4.180 4.180
DIMENSIONAL DATA
Guide Cage Length (From Anvil up to Bottom) m 3.0 3.0 3.0 3.0
Min. Guide Cage overall dimension m ~4.0 ~3.9 ~3.9 NA
Max. Hammer length incl. Guide Cage m 17.6 17.5 17.5 21.8
CUSHION DATA
Type (Wood) - Bongossi Bongossi Bongossi Bongossi
Elastic Modulus MPa 2000 2000 2000 2000
Area ( Diameter = (Area*4/)1/2 ) cm 19596 19596 19596 28652
Thickness mm 250 250 250 300
Restitution Coefficient - 0.75 0.75 0.75 0.75
HAMMER DATA vs. PILE
Pile sleeve suitable for piles O.D. up to in 72 (84) 84 84 84
Standard Anvil suitable for piles up to in 4272 & 4284 4284 4284 4284
Max. Batter Pile Deg NA NA NA NA
Legend: NA= Not Available; GRLWeap = Driveability Software-Name; Ass.= Assumed; C.o.G.= Centre of Gravity.

5 of 13
 DELMAG D DIESEL HAMMER DATA SHEET- Rev. I (15/05/2007)

DELMAG DELMAG DELMAG DELMAG

HAMMER TYPE: DIESEL (Only Above Water)
D46-32 D55 D62-12 D62-22
OPERATING DATA Unit
Max. Rated Energy (Setting 1) kNm 165.73 (100%) 169.551(100%) 206.77 219 223.261(100%)
Partial Rated Energy (Setting 2) kNm 137.56 (~83%) 140.73 (~83%) 171.62 (~83%) 185.31 (~83%)
Partial Rated Energy (Setting 3) kNm 109.38 (~66%) 111.90 (~66%) 134.47 (~66%) 147.35 (~66%)
Min. Rated Energy (Setting 4) kNm 70.85 (~43%) 84.77 (~50%) 103.385 (~50%) 107.05 (~48%)
Blow Rate at max. Energy bl/min 53 47 50 50
Impact Weight (Piston) kN 45.123 52.777 60.787 60.787
Maximum Stroke (GRLWeap database) m 3.99 3.398 3.874 4.04
Hammer Efficiency (Continuous mode) % 80 80 80 80
Hammer Efficiency (At Restart or Full Set-up) % 70 70 70 70
Company Number Az. 552473 750856/753493 764241 764350 To Rent
WEIGHT DATA
Helmet (Depend on pile OD) (GRLWeap database) N 17.35 (1624) 16.90 (2436) 25.35 (3642) 39.59 (4248)
Offshore Guide Cage kN NA NA NA NA
Weight in Air kN 235.44 294.3 305 305
C.o.G. measured from top of Pile m 3 3 3 3
DIMENSIONAL DATA
Guide Cage Length (From Anvil up to Bottom) m 2.5 1.3 ~3 3.25 ~3
Min. Guide Cage overall dimension (i.e. diameter) m ~1.7 ~1.7 ~2.04 ~2.04
Hammer length incl. pile Guide Cage m 8 NA 9 9
CUSHION DATA
1)
Type (by Polypenco bv) (GRLWeap database) - Monocast MC 904P / 2)Conbest-Micarta
Elastic Modulus MPa 12071) 12071) 12071) 28002) 12071)
Area (O.D. = 510mm) cm 2041 2041 2041 2041 2041
Thickness mm 120 120 120 120
Restitution Coefficient - 0.92 0.92 0.92 0.80 0.92
HAMMER DATA vs. PILE
Pile sleeve suitable for piles O.D. up to in 36 60 50 50
Standard Anvil suitable for piles up to in 2036 2060 2050 2050
Max. Batter Pile (hammer with extension of upper cylinder) Deg 18.3 (45) 18.3 (45) 26.6 (45) 26.6 (45)
Legend: NA= Not Available; GRLWeap = Driveability Software-Name; Ass.= Assumed; C.o.G.= Centre of Gravity.

6 of 13
 DELMAG D DIESEL HAMMER DATA SHEET- Rev. I (15/05/2007)

DELMAG DELMAG DELMAG

HAMMER TYPE: DIESEL (Only Above Water)
D80-12 D80-23 D100-13
OPERATING DATA Unit
Max. Rated Energy (Setting 1) kNm 258.08 (100%) 288.33 (100%) 360.40 (100%)
Partial Rated Energy (Setting 2) kNm 231.50 (~89.7%) 258.63 (~89.7%) 323.28 (~89.7%)
Partial Rated Energy (Setting 3) kNm 189.95 (~73.6%) 212.21 (~73.6%) 265.26 (~73.6%)
Min. Rated Energy (Setting 4) kNm 165.43 (~64.1%) 184.82 (~64.1%) 231.02 (~64.1%)
Blow Rate at max. Energy bl/min 37 35 35
Weight of Ram (Impact Weight-Piston) kN 80 80 100
Maximum Stroke m 3.226 3.604 3.604
Hammer Efficiency (Continuous mode) % 80 80 80
Hammer Efficiency (At Restart or Full Set-up) % 70 70 70
Company Number Az. 764353 276908-SA 620852 276904-SA 623597
WEIGHT DATA
Helmet (Depend on pile OD) (GRLWeap database) kN 17.35 (1624) 16.90 (2436) 25.35 (3642) 39.59 (4248)
Offshore Guide Cage kN NA NA NA
363
Weight in Air kN 343 (2048) / 383 (5080)
(2048 & 5080)
C.o.G. measured from top of Pile m 3.1 3.1 3.5
DIMENSIONAL DATA
Guide Cage Length (From Anvil up to Bottom) m 2.1 2.5 3.35 3.2 3.2
Min. Guide Cage overall dimension m ~2.8 ~2.8 ~2.8
Hammer length incl. pile Guide Cage m NA NA 10
CUSHION DATA
Aluminium /
Type - Aluminium / HGW
HGW (670 mm)
Elastic Modulus MPa 9417 9417 9417 9417
Area cm 2041 2041 2041 3524
Thickness mm 105 105 105 105
Restitution Coefficient - 0.80 0.80 0.80 0.80
HAMMER DATA vs. PILE
Pile sleeve suitable for piles O.D. up to in 80
Standard Anvil suitable for piles up to in (2048) (5080)
Max. Pile True Batter Deg 18.3
Legend: NA= Not Available; GRLWeap = Driveability Software-Name; Ass.= Assumed; C.o.G.= Centre of Gravity.
7 of 13
 DELMAG D DIESEL HAMMER DATA SHEET- Rev. I (15/05/2007)

DELMAG DELMAG
HAMMER TYPE: DIESEL (Only Above Water)
D150-42 D200-42
OPERATING DATA Unit
Max. Rated Energy (Setting 1) kNm 512.10 (100%) 682.80 (100%)
Partial Rated Energy (Setting 2) kNm 459.35 (~89.7%) 612.47 (~89.7%)
Partial Rated Energy (Setting 3) kNm 376.91 (~73.6%) 502.54 (~73.6%)
Min. Rated Energy (Setting 4) kNm 328.26 (~64.1%) 437.68 (~64.1%)
Blow Rate at max. Energy bl/min 36 36
Weight of Ram (Impact Weight-Piston) kN 150 200
Maximum Stroke m 3.414 3.414
Hammer Efficiency (Continuous mode) % 80 80
Hammer Efficiency (At Restart or Full Set-up) % 70 70
Company Number Az. To Rent
WEIGHT DATA
Helmet (Depend on pile OD) (GRLWeap database) kN 4.4 218.27
Offshore Guide Cage kN 16.7 519.93
Weight in Air kN 45.7 109.5
C.o.G. measured from top of Pile m 5.4 2.6
DIMENSIONAL DATA
Guide Cage Length (From Anvil up to Bottom) m 2 up to 5 1 up to 5
Min. Guide Cage overall dimension m 2 ~2.8
Hammer length incl. pile Guide Cage m 11.03 up to 14.03 12.700 up to 16.700
CUSHION DATA
Type - Aluminium / HGW
Elastic Modulus MPa 9417 9417
Area cm 3370 7238
Thickness mm 105 105
Restitution Coefficient - 0.8 0.80
HAMMER DATA vs. PILE
Pile sleeve suitable for piles O.D. up to in 60 84
Standard Anvil suitable for piles up to in 36/40/42/48/60 48/54/60/72/84
Max. Pile True Batter Deg 18.3 18.3
Legend: NA= Not Available; GRLWeap = Driveability Software-Name; Ass.= Assumed; C.o.G.= Centre of Gravity.

8 of 13
 Pile vs. Hydraulic Hammer (Menck MHU)

Menck Suitable Pile Diameter [inch] vs. Menck Anvil (Inner dome)
Hammer 18 20 30 32 36 38 40 42 44 46 48 50 52 56 58 60 62 72 84 102
MHU 195 OK OK OK OK OK OK OK OK Anvil Inner Dome Diameter 345mm, Max. Allowable Wall Thickness for 18 Pile is 2.25 in.
MHU 220 OK OK OK OK OK OK OK OK Anvil Inner Dome Diameter 345mm, Max. Allowable Wall Thickness for 18 Pile is 2.25 in.
Anvil Inner Dome Diam. 750mm, Max.
MHU 600T All. Wall Thick. for 36 Pile is 3.25 in. OK OK OK OK OK OK OK OK OK OK OK OK - - - -

MHU 800S Anvil Inner Dome Diam. 1038mm, Max. Allowable Wall Thickness for 48 Pile is 3.5 in. OK OK OK OK OK OK OK OK OK -
Anvil Inner Dome Diam. 1066mm, Max. Allowable Wall Thickness for 48 Pile is 3 in. OK OK OK OK OK OK OK OK OK -
MHU 1000
Anvil Inner Dome Diameter 1300mm, Max. Allowable Wall Thickness for 56 Pile is 2.375 in. OK OK OK OK OK OK OK
MHU 1700 Anvil Inner Dome Diam. 1046mm, Max. Allowable Wall Thickness for 48 Pile is 3.375 in. OK OK OK OK OK OK OK OK OK OK
MHU 3000 Anvil Inner Dome Diameter 1360mm, Max. Allowable Wall Thickness for 60 Pile is 3.325 in. OK OK OK OK OK
MHU 270T - OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK Inner Dome Diam. 420m
MHU 400T Anvil Inner Dome Diam. 812mm OK OK OK OK OK OK OK OK OK OK OK OK - - - -
MHU 500T Anvil Inner Dome Diam. 812mm OK OK OK OK OK OK OK OK OK OK OK OK OK OK Up to 86 Pile OD
Legend: OK= Suitable

ANVIL DOME (Menck MHU...)

9 of 13
 Pile vs. Diesel Hammer (Delmag D)
Delmag Suitable Pile Diameter [inch] vs. Delmag Anvil
Hammer 20 30 32 36 38 40 42 44 46 48 50 52 54 58 60 72 84
D46-32 OK OK OK OK - - - - - - - - - - - - -
D55 OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK - -
D62-12/22 OK OK OK OK OK OK OK OK OK OK OK - - - - - -
OK OK OK OK OK OK OK OK OK OK (Sleeve 2048)
D80-12
(Sleeve 4884) OK OK OK OK OK OK OK OK
OK OK OK OK OK OK OK OK OK OK (Sleeve 2048)
D80-23
(Sleeve 4884) OK OK OK OK OK OK OK OK
OK OK OK OK OK OK OK OK OK OK (Sleeve 2048)
D100-13
(Sleeve 4884) OK OK OK OK OK OK OK OK
D200-42 NA NA NA NA NA NA NA NA NA OK NA NA OK NA OK OK OK
Legend: NA = Not Available; OK= Suitable.

FLAT ANVIL (Delmag Hammer)

Pile vs. Delmag D200 Hammer Anvil

Menck Suitable Pile Diameter vs. Max. Allowable Pile Wall Thickness [inch x mm]
Hammer 20 30 32 36 40 42 44 46 48 50 52 54 58 60 72 84
D200-42 - - - - - - - - 60.6 - - 60.8 - 51 60.9 73.3

ANVIL with STEPS (Delmag D200-42 & Menck MRBS)

10 of 13
 Pile vs. Steam Hammer Anvil (Menck MRBS)
Menck Suitable Pile Diameter vs. Max. Allowable Pile Wall Thickness [inch x inch]
Hammer 20 30 32 36 40 42 44 46 48 50 52 54 58 60 72 84
MRBS 1800 - 1 1.625 - 2.625 3.625 - 1.75 1 2 3 4 - - - -
MRBS 2500/S - 1.875 2.875 1.875 1.5 2.5 - 5 2.5 1 2 2 - - - -
- 1.25 2.25 1 1.375 - 1.625 - 1.75 - Sleeve 3048
MRBS 3000 Sleeve
- 1.75 2.75 1.75 1.25 2.25 3.25 1 2 3 - 1.9 - 1.625 2.5
3062
- Sleeve 4272 2.875 3.875 - 1.875 - 1.875 2.8 1.875 2.875 5 -
MRBS 4600
- Sleeve 4284 1.125 2.125 3.125 4 - 1.625 2.625 1.75 2.875 2.875 2. 875
- - - - - 1.75 - 1.375 2.375 - 1.75 2.75 4.75 5 2.375 3. 25
MRBS 5000/S
- - - - - 3 4 5 5 - 5 5 1.625 2.625 2.375 2.875
MRBS 8000 - - - - - 2.5 1.75 1 2 - 1.75 2.75 1.75 2.625 5 3. 125

Pile vs. Steam Hammer Anvil (Menck MRBS)

Menck Suitable Pile Diameter vs. Max. Allowable Pile Wall Thickness [inch x mm]
Hammer 20 30 32 36 40 42 44 46 48 50 52 54 58 60 72 84
MRBS 1800 - 25.4 41.275 - 66.675 92.075 - 44.45 25.4 50.8 76.2 101.6 - - - -
MRBS 2500/S - 47.625 73.025 47.625 38.1 63.5 - 127 63.5 25.4 50.8 50.8 - - - -
- 28.575 57.15 25.4 34.925 - 41.275 - 44.45 - Sleeve 3048
MRBS 3000 Sleeve
- 44.45 69.85 44.45 31.75 57.15 82.55 25.4 50.8 76.2 - 48.26 - 41.275 63.5
3062
- Sleeve 4272 73.025 98.425 - 47.625 - 47.625 73.025 47.625 73.025 127 -
MRBS 4600
- Sleeve 4284 28.575 53.125 79.375 101.6 - 41.275 66.675 44.45 73.025 73.025 73.025
- - - - - 44.45 - 34.925 60.325 - 44.45 69.85 120.65 127 60.325 82.55
MRBS 5000/S
- - - - - 76.2 101.6 127 127 - 127 127 41.275 66.675 60.325 73.025
MRBS 8000 - - - - - 63.5 44.45 25.4 50.8 - 44.45 69.85 44.45 66.675 127 107.95

11 of 13
 Typical O.D. Pile vs. Typical Heavy Plate (Pile) Wall Thickness
O.D. Pile Min. WT W.T. [mm]
18 - 25.4 30 35 38.1 40 45 50 50.8 55 60 63.5 65 70 75 80 90 100 110
20 - 25.4 30 35 38.1 40 45 50 50.8 55 60 63.5 65 70 75 80 90 100 110
24 13 25.4 30 35 38.1 40 45 50 50.8 55 60 63.5 65 70 75 80 90 100 110
28 - 25.4 30 35 38.1 40 45 50 50.8 55 60 63.5 65 70 75 80 90 100 110
30 14 25.4 30 35 38.1 40 45 50 50.8 55 60 63.5 65 70 75 80 90 100 110
32 14 25.4 30 35 38.1 40 45 50 50.8 55 60 63.5 65 70 75 80 90 100 110
36 16 25.4 30 35 38.1 40 45 50 50.8 55 60 63.5 65 70 75 80 90 100 110
38 - 25.4 30 35 38.1 40 45 50 50.8 55 60 63.5 65 70 75 80 90 100 110
40 - 25.4 30 35 38.1 40 45 50 50.8 55 60 63.5 65 70 75 80 90 100 110
42 17 25.4 30 35 38.1 40 45 50 50.8 55 60 63.5 65 70 75 80 90 100 110
44 - 25.4 30 35 38.1 40 45 50 50.8 55 60 63.5 65 70 75 80 90 100 110
46 - 25.4 30 35 38.1 40 45 50 50.8 55 60 63.5 65 70 75 80 90 100 110
48 19 25.4 30 35 38.1 40 45 50 50.8 55 60 63.5 65 70 75 80 90 100 110
50 - 25.4 30 35 38.1 40 45 50 50.8 55 60 63.5 65 70 75 80 90 100 110
52 - 25.4 30 35 38.1 40 45 50 50.8 55 60 63.5 65 70 75 80 90 100 110
54 - 25.4 30 35 38.1 40 45 50 50.8 55 60 63.5 65 70 75 80 90 100 110
56 - 25.4 30 35 38.1 40 45 50 50.8 55 60 63.5 65 70 75 80 90 100 110
60 22 25.4 30 35 38.1 40 45 50 50.8 55 60 63.5 65 70 75 80 90 100 110
72 25 25.4 30 35 38.1 40 45 50 50.8 55 60 63.5 65 70 75 80 90 100 110
84 28 - 30 35 38.1 40 45 50 50.8 55 60 63.5 65 70 75 80 90 100 110
96 31 - - 35 38.1 40 45 50 50.8 55 60 63.5 65 70 75 80 90 100 110
102 - - - 35 38.1 40 45 50 50.8 55 60 63.5 65 70 75 80 90 100 110
108 34 - - 35 38.1 40 45 50 50.8 55 60 63.5 65 70 75 80 90 100 110
120 37 - - 35 38.1 40 45 50 50.8 55 60 63.5 65 70 75 80 90 100 110

Note: Typical Plate Length 3m (10ft); Typical Plate width up to 2.7m. Plate-Pile Typical Fabrication: welded (SAW). Typical Steel Grade: X52
(355MPa), A36 (235MPa) & A40 (275MPa).

12 of 13
 Typical Plate-Pile Wall Thickness (AISC)
W.T. [in (mm)]
1 (25.4) 1.125 (28.575) 1.25 (31.75) 1.375 (34.925) 1.5 (38.1) 1.625 (41.275) 1.75 (44.45) 1.875 (47.625)
2 (50.8) 2.125 (53.125) 2.25 (57.15) 2.375 (60.325) 2.5 (63.5) 2.625 (66.675) 2.75 (69.85) 2.875 (73.025)
3 (76.2) 3.125 (79.375) 3.25 (82.55) 3.375 (85.725) 3.5 (88.9) 3.625 (92.075) 3.75 (95.25) 3.875 (98.425)
4 (101.6) 4.25 (107.95) 4.5 (114.3) 4.75 (120.65) Over 5 - - -

Note: Typical Plate Length 3m (10ft); Typical Plate width up to 2.7m. Plate-Pile Typical Fabrication: welded (SAW). Typical Steel Grade: X52
(355MPa), A36 (235MPa) & A40 (275MPa).

Pile vs. Typical True Batter

O.D. Batter [deg]

Max.
Min. 4.76 5.19 5.71 7.13 6.71 8.13 9.46 9.93 10.30* 11.31 12.52 18.43
18120 14.04
1* (1:12) (1:11.5) (1:10) (1:8) (1:8.5) (1:7) (1:6) (1.4:8) (1:5.5) (1:5) (1:4.5) (1:3)
(1:4)
Note * :
- Skirt and Conductor pile are generally installed in vertical position and the batter is conservatively assumed equals to 1 (included
tolerances)
- For large pile inclinations (over 10) particular measures on the hammer (Menck, Delmag) might be necessary to avoid hammer efficiency
reducing (e.g. hammer stroke) and pile driveability cost increasing.

Legend: True Batter X:12 [e.g. arctg (3:12) =14.04 deg ]. True Batter 1:Y [e.g. arctg (1:1) =45deg)]

13 of 13