BRITISH STANDARD Plastics piping systems — Buried and above ground systems for water and other fluids under pressure — Performance characteristics for pipes, fittings and their joints Tes 29040-2929 00048, vITHOUT BSI PERMISSION EXCE |RMITTED BY COPYRIGHT LAW BS EN 15014:2007 British Standards.BS EN 15014:2007 ‘This British Standard was ppblished under the authority ofthe Standards Posey and Stratozy Cemmittor fon #1 Mlareh 2008, © Bsi.2008 ISBN 978 0 580 54579 5 National foreword ‘This British Standard was published by BSI. It is the UK implementation of EN 15014:2007, ‘The UK participation in its preparation was entrusted by Technical Committee PRI/EB, Plastics piping systems, to Subcommittee PRIU86/2, Plastic piping for pressure applications, ‘This British Standard is intended as a means of demonstrating compliance with the Construetion Products Direetive (89/106/EEC), and affixing the CE mark, ‘The Essential Requirements contained in this British Standard are concepts related to the Construction Products Directive and they are not necessarily indicative of all the performance requirements or suitability for the service conditions likely to be encountered in a particular pipework application. ‘The CE mark indicates only that a product may legallly be placed on the market in the EU. It does not indieate or guarantoe inherent quality of the CE marked pipework components. It should be noted that manufacturers are entitled to declare “No Performance Determined” againat some or all of these Essential Requirements and yet still affix the CH mark to their products. Users are advised to check the background details with the manufacturers claims for the CE marked produets. Such details may be available on an appropriate Internet website or accompanying, Company documentation. Compliance with this British Standard does not necessarily mean that products bearing the CE mark are fit for a particular intended purpose. ‘This Standard does not replace the corresponding BS EN Product Standards (ce national annex NA) which do contain detailed performance requirements for pipes, fittings and joints manufactured from particular plastics materials. Amendments issued since publication ‘Amd.No. [Date CommentsBS EN 15014:2007 ‘This British Standard makes no reference to the suitability of pipework for conveying drinking water. The legislation setting out these requirements for water supply installations in the UK is for installations for public water supplies: + the Water Supply (Water Quality) Regulations 2000, Regulation 31 England), + the Water Supply (Water Quality) Regulations 2001, Regulation 31 (Wales), + the Water Supply (Water Quality) Regulations 2001, Regulation 27 (Scotland); and + the Water Supply (Water Quality) Regulations 2007, Regulation 30 (Northern Ireland); and for installations for consumers’ premises: + the Water Supply (Water Fittings) Regulations 1999 (England and Wales), the Water Byelaws 2000 (Scotland) and the current requirements for Northern Ireland Aist of product standards used in conjunction with this standard is included in a national annex NA. A list of organizations represented on PRU8®2 can be obtained on request to its secretary. ‘This publication does not purport to include all the neeessary provisions of a contract. Users are responsible for its eorrect. application Compliance with a British Standard cannot confer immunity from legal obligationsenone Suns a, blankEUROPEAN STANDARD EN 15014 NORME EUROPEENNE EUROPAISCHE NORM (October 2007 ICS 23,040.20; 23.040.45 English Version Plastics piping systems - Buried and above ground systems for water and other fluids under pressure - Performance characteristics for pipes, fittings and their joints ‘Systomos de canaiistions on piastque - Systbmos Kunstetoft Fohrtotungsystome - Erd. und obertrcch ontorrée et aérons pout eau ot autos uldos avec proscion vorlegto Druckronriotungssystome for Wasser und andre CCaraetéretiques do portormance pour tubes, raccords ot Flaseigkaion -Elgoncenatton tar alo Gobrauchstaugichkot Tere assemblages ‘von Roten, Formetocken und deren Verbindungen ‘This European Standard was approves by CEN on 23 August 2007, (CEN members are bound to comply wit the CENCENELEC intemal Regulations which stipulate the conditons for giving this European ‘Standard the status of a national standard without any aeration. Upto-dae ists and biblographical references eanceming such national slangarde may bo obtained on applleation tothe CEN Managomant Cont orto any CEN member. “This Europoan Standard oxists in threo offal vorsione (English, Fronch, Gorman. A version in any other language mace by translation lundor the responsibilty of a CEN momber ino Is own language and noted to tho GEN Managamont Cantre has the came status a to olical versions ‘CEN members are the national standards bodies of Aust, Belgum, Bulcatia, Cyprus, Czech Repubile, Denmark, Estonia, Finland, Franes, Germany, Greece, Hungary, eeland, lelard, Kay, Lalva, Uthuania, Luxembourg, Maka, Nethetlands, Norway, Poland, Portugal, Fomania, Slovakia, Slovenia, Spain| Sweden, Switzerland and United Kingdom ama! EUROPEAN COMMITTEE FOR STANDARDIZATION COMITE EUROPEEN DE NORMALISATION Management Centre: nue de Stassart, 368-1050 Brussels (©2007 CEN All rghts of explotation in any form and by any means reserves Rt. No. EN 160142007: E \Worlawide for CEN ratonal MemberBS EN 15014:2007 EN 15014:2007 (E) Contents Page 3 Terms, definitions and symbols .. 4 Performance requirement... ne st coi erremeaeantat 4.1 Reaction to fire for applications inside building 7 42 External pressure strength. 43 Internal pressure strength. 4.4 Dimensional tolerances... 45 Tightness (air and liquid)... sn woe 46 Durability. 4.7 Dangerous substances 5 Test methods. 5.1 Reaction to fire for applications inside bui 5.2 Determination of the nominal pressure 53 Internal pressure strength. 5.4 Dimensional tolerances. 55 Tightness.. 56 Durability. 6 Evaluation of conformity... 7 7 a evrneee AO 61 General. 62 __ Initial type testing.. 63 Factory production control... eer 64 One-off products and products produced in very low quantities... Annex A (normative) Product standards for buried and above-ground pressure piping systems in Plastics materials for water for general purposes, drainage, sewerage, irrigation and other fluids.. Annex B (normative) Standards for assessment of conformity for buried and above-ground pressure sewerage, irrigation and 19 piping systems in plastics materials for water for general purposes, drainage, other fluids ‘Annex ZA (informative) Clauses of this European Standard addressing the provisions of EU Construction Products Directive ZA1 Scope and relevant characteristics. ZA2 Procedure for attestation of conformity of plastics pipes and fittings... ZA21 Systems of attestation of conformity. ZA22 EC Certificate and Declaration of conformity. ZA3 CE marking and labelling ZA34 CE marking requirements. ZA32 _ Simplified CE marking wi ZA.3.2.1 General .. ZA3.2.2 Minimum rules for Bibliography...BS EN 15014:2007 Foreword This document (EN 15014:2007) has been prepared by Technical Committee CEN/TC 156 “Plastics piping systems and ducting systems”, the secretariat of which is held by NEN This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2008, and conflicting national standards shall be withdrawn at the latest by July 2009. This document has been prepared under the mandate M/131 "Pipes, tanks and ancillaries not in contact with, water intended for human consumption” given to CEN by the European Commission and the European Free Trade Association and support essential requirements of EU Directives. For the relationship with EU Directives, see informative Annex ZA, which is an integral part of this document. ‘According fo the CEN/CENELEC Internal Regulations, the national standards organizations of the following ‘countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czach Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Siovakia, Siovenia, Spain, ‘Sweden, Switzerland and United Kingdom.BS EN 15014:2007 EN 15014:2007 (E) Introduction This European Standard contains only the performance characteristics needed to meet the essential requirements of EU Directive(s). It does not cover all characteristics of the products. These are specified in the standards listed in Annex A or in other appropriate product specifications. This harmonised European Standard is part of a family of cluster standards addressing plastics systems. The relationship is shown below. ing P] this harmoniaed Eutopoan Standard Material independent International product Products for standard which no standard A andlor B exists ete. Specific solutions. L For the harmonisation of pressure plastics piping systems (this European Standard) the following applies: Harmonisation of pressure plastics piping products y Y Harmonised luster For pipes Annex ZA ‘standard for and fitings of this valves [2] For valves standard (covered products ‘ee Bbilograchy [}otM) Figure 1BS EN 15014:2007 1 Scope ‘This European Standard specifies performance requirements for plastics pipes, fittings and their joints for buried or above-ground pressure applications for water for general purposes, drainage, sewerage and irrigation, as well as for any other pressure application with other fluids covered by the Construction Products Directive with the exception of drinking water distribution for human consumption, It gives associated test methods for verification and evaluation of conformity with this European Standard NOTE Compliance of pipes, fitings and their joints with this document does not confer a presumption of fitness of the product for the transport of water intended for human consumption within the meaning of the Directive 89/10B/EEC. However, until the operation of the envisaged European Acceptance Scheme for construction products in contact with water Intended for human consumption and the revision of this standard, products conforming to this standard could be Used for the transport of water intended for human consumption if they conform to the relevant national, regional or local regulatory provisions or recommendations applicable in the place of use, 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 681-1, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage applications — Part 1: Vulcanized rubber EN 681-2, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage applications — Part 2: Thermoplastic elastomers EN 681-4, Elestomeric seals — Materials requirements for pipe joint seals used in water and drainage applications — Part 4: Cast polyurethane sealing elements EN 713, Plastics piping systems — Mechanical joints between fittings and polyolefin pressure pipes — Test ‘mathod for leaktightnass under intemal pressure of assemblies subjocted to bending EN 715, Thermoplastics piping systems — End-load bearing joints between small diameter pressure pipes and fittings — Test method for lealtightness under internal water pressure, ineluding end thrust EN 911, Plastics piping systems — Elastomerie sealing ring type joints and mechanical joints for thermoplastics pressure piping — Test method for leaktightness under external hydrostatic pressure EN 1394, Plastics piping systems — Glass-reinforced thermosetting plestics (GRP) pipes — Determination of the apparent initial circumferential tensile strength EN 1796, Plastics piping systems for water supply with or without pressure — Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) EN 13501-1, Fire classification of construction products and building elements — Part 1: Classification using test data from reaction to fire tests EN 14364, Plastics piping systems for drainage and sewerage with or without pressure — Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) — Specifications for pipes, fittings and joints EN 15012:2007, Plastics piping systems — Soil and waste discharge systems within the building structure — Porformance characteristics for pipes, fittings and their jointsBS EN 15014:2007 EN 15014:2007 (E) EN ISO 1167-1, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 1: General method (ISO 1167-1:2006) EN ISO 1167-2, Thermoplestics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance fo internal pressure — Part 2: Preparation of pipe test pieces (ISO 1167-2:2006) prEN ISO 1167-3:2005, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 3: Preparation of components (ISO/DIS 1167-3:2005) prEN ISO 1167-4:2008, Thermoplastics pipes, iittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 4: Preparation of assemblies (ISO/DIS 1167-4:2006) EN ISO 3126, Plastics piping systoms — Plastics components — Determination of dimensions (ISO 3126:2005) EN ISO 9001:2000, Quality management systems — Requirements (ISO 9001:2000) EN ISO 9080, Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation (ISO 9080:2003) EN ISO 12162, Thermoplastics materials for pipes and fittings for pressure applications — Classification and designation — Overall service (design) coefficient (ISO 12162:1995) EN ISO 13783, Plastics piping systems — Unplasticized poly(vinyl chloride) (PVC-U) end-load-bearing double socket joints — Test method for leaktightness and strength while subjected to bending and internal pressure (ISO 13783:1997) EN ISO 13848, Plastics piping systems — End-load-bearing and non-end-load-bearing assemblies and joints for thermoplastics pressure piping — Test method for long-term leaktightness under internal water pressure (ISO 13846:2000) ISO 161-1, Thormoplastics pipes for the conveyance of fluids — Nominal outside diameters and nominal pressures — Part 1: Metric series ISO 17456, Plastics piping systems — Multilayer pipes — Determination of long-term strength ISO 21004, Plastics piping systems — Muttilayer pipes and their joints, based on thermoplastics, for water supplyBS EN 15014:2007 3 Terms, definitions and symbols For the purposes of this document, the following terms, definitions and symbols apply. 34 nominal size (DN) ‘numerical designation of the size of a component, other than a component designated by thread size, which is ‘a convenient round number approximately equal to the manufacturing dimension in millimetres (mm) NOTE This can apply to either the internal diameter (DN/ID) or external diameter (DN/OD). 32 nominal outside diameter dy spocifiod diameter limetres, assigned to a nominal size 33 nominal pressure (PN) ‘numerical designation used for reference purposes related to the mechanical characteristics of the component of a piping system NOTE For plastic ping systems conveying water it corresponds to the maximum continuous operating pressure in bar, which can be sustained with water at 20 °C for thermoplastics and 35 *C for thermosetting materials, based on the minimum design coefficient 4 Performance requirements 44 Reaction to fire for appl ns inside bi 9 Where subject to regulatory requirements, the product shall be tested and classified in accordance with 5.1. 4.2 External pressure strength ‘The external pressure strength of pressure piping systems is deemed to be satisfied by the intemal pressure strength as given in 4.3. 4.3 Internal pressure strength 4.3.1 Determination of nominal pressure PN For thermoplastics materials the intemal pressure strength of the pipe and filting shall be determined in acoordance with 5.2.1 and shall be declared by the manufacturer as nominal pressure PN in accordance with 1SO 161-1 and including PN 26 where applicable. ‘The overall service (design) coefficient shall not be less than that specified in EN ISO 12162 for the relevant material. For thermosetting materials the internal pressure strength of the pipe or fiting shall be tested in accordance with 5.2.2 and shall be dedlared by the manufacturer as nominal pressure in accordance with EN 1796 or EN 14364, For multilayer pipes the intemal pressure strength shall be tested and declared by the manufacturer in accordance with 5.2.3BS EN 15014:2007 EN 15014:2007 (E) 4.3.2 Verification of pressure strength ‘The verification of the internal pressure strength of pipes and fitings shall be done in accordance with 5.3. 4.4 Dimensional tolerances ‘The manufacturer shall declare the dimensional tolerances for the jainting of the components, either by means of @) reference to a specific European product standard as given in Clause 2 or in Annex A, as applicable, or b) inthe absence of a European Standard, reference to a specific European product specification published by a recognized European organization or, ©) inthe absence of a) and b) reference to an Intemational Standard, or 4) in the absence of a), b), and c), by stating the values of his own specification and associated jointing method. Dimensions shall be measured in accordance with 5.4 and shall be within the declared tolerances, 4.5 Tightness (air and liquid) For products in accordance with this standard, leaktightness is required. Products covered by one of the standards listed in Annex A and having passed the type testing in accordance with the assessment of conformity part, are deemed to be leaktight (for standards with separate assessment of conformity parts see ‘Annex B). ‘Sealing rings (and gaskets) shall conform to EN 681-1, EN 681-2 or EN 681-4, as applicable. connections shail be tested in accordance with 5.5. No leakage shall occur during the test period 46 Durability 4.81 Durability of pipes and fittings Pipes and fittings meeting the requirements of 4.3.1 are deemed to have @ reasonable economic working life NOTE The piping components are expected to last at least the lifetime of the network where they are installed. If the nature of the fluid is different from water or this fluid or water has a higher tomporature than 20 °C (35 °C for thermosetting materials), guidance for de-rating the pressure shall be in accordance with the appropriate following standards: EN 1778 [13], EN 1452-2 [12] for PVC-U, ISO 13761[14] for PE, EN 1796 and EN 14364 for thermosetting materials and ISO 17456 or ISO 21004 for multilayer piping systems. Instead of de-rating the pressure, a shorter lifetime may be declared 46.2 Durability of elastomeric sealing joints The tightness of elastomeric sealing joints is deemed to be durable if the sealing element conforms to EN 681-1, EN 681-2 or EN 881-4, as applicable. 4.7 Dangerous substances Attention is drawn to NOTE 1 and NOTE 2in ZA.1BS EN 15014:2007 NOTE Mandate M/366 "Development of horizontal standardised assessment methods for harmonised approach relating to dangerous substances under the Construction Products Directve (CPD)* as issued by the European Commission, will rquite specifications relating to dangerous substances once applicable to the covered products. 5 Test methods 5.1 Reaction to fire for applications inside bui Classification shall be in accordance with EN 13501-1. Mounting and fixing of pipes shall conform to Annex A in EN 15012:2007. If no pipes are available, testing of fittings may be done in form of a linear assembly, 0.9. couplers. NOTE Incase where e.g, the given dimensions do not exist the choice of dimensions and the mounting and fixing should be agreed between the manufacturer and the notified body. 5.2 Determination of the nominal pressure 5.2.1 Determination of the nominal pressure PN for thermoplastics piping systems For thermoplastics materials the nominal pressure PN shall be determined as follows: 1a) determine the Gjp, Value in accordance with EN ISO 9080. Data provided by either the compound manufacturer or the product manufacturer may be taken into account; b) classify the material (MRS) and calculate the design stress in accordance with EN ISO 12162; ¢) calculate the PN for a chosen pips series (SDR series) in accordance with ISO 161-1. 5.2.2 Determination of the nominal pressure PN for thermosetting piping systems For thermosetting materiais the nominal pressure PN shall be determined in accordance with the procedures given in EN 1796 or EN 14364, as applicable. 5.2.3 Determination of the nominal pressure PN for multilayer piping systems For multilayer piping systems the nominal pressure PN shall be determined in acoordance with ISO 17456. 5.3. Internal pressure strength 5.3.1 Internal pressure strength for thermoplastics products For checking the intemal pressure strength testing shall be done in accordance with the appropriate parts of EN ISO 1167 using circumferential stresses or test pressures as given in the relevant product standards in Annex A, 5.3.2 Internal pressure strength for thermosetting products For checking the internal pressure strength testing shall be done in accordance with EN 1796 or EN 14364 using the test method given in EN 1394, 5.3.3 _ Internal pressure strength for multilayer piping systems For checking the internal pressure strength testing shall be done in accordance with ISO 21004.BS EN 15014:2007 EN 15014:2007 (E) 5.4 Dimensional tolerances ‘The dimensions shall be measured in accordance with EN ISO 3126. 5.5 Tightness ‘The leaktightness of joints shall be tested in accordance with EN 715 for joints for polyolefin pipes and with EN ISO 13846 and EN ISO 13783 for joints for other thermoplastics pipes as applicable. Joints with ‘mechanical fittings and polyethylene pipes shall be tested according EN 911 and EN 713. For joints for thermosetting pipes, tests referenced in EN 1796 or EN 14364 shall be applied, depending on the type of joint. For joints for multilayer pipes, tests referenced in ISO 21004 shall be applied, depending on the type of joint. NOTE The test parameters are set by the product standards making reference to these test standards. Fused, cemented and adhesive joints are deemed to be leaktight when assembled in accordance with the ‘manufacturer's instructions. Such instructions shall bo made available by the manufacturer. 5.6 Durability Piping components conforming with the requirements ofthis document and with a declared nominal pressure, which is determined according to 5.2 of this European Standard, shall be deemed to be durable for a reasonable economic working life. 6 Evalual n of conformity 6.1 General The conformity of pipes and fittings with the requi values (including classes) shall be demonstrated by: ments of this European Standard and with the declared — initia type testing; — factory production control by the manufacturer, including product assessment. For the purposes of testing, pipes and fittings may be grouped into families, where it is considered that the results for ons or more characteristics from any product within the family are representative for the same characteristics for all products within that family. NOTE1 A product may be in more than one family for different characteristics, For type testing the following family groups apply: a) Size groups for pipes and fitings as given in Table 4BS EN 15014:2007 Table 1 — Size groups Range of nominal diameters, d, Size group for thermoplastics material | _ for thermosetting plastics 1 [ 4,<63 100 < dj, < 600 2 | 63 3 800 4 | > 630 = b) Fitting groups for thermoplastics piping components as given in Table 2. NOTE2 — Fitng groupe are cuenty not avafoie fe thomosotin png components Table 2—Fiting groups [ Fitting group | Thermoplastica piping components _ | 1 | Bends and elbows 2 | _ Branches 3 Other fittings 62 I ial type testing 6241 General Relevant type tests shall be carried out on new products and whenever there is a change in design, in material and/or in production method, other than routine in-process adjustment and extension of the product range (S90 Table 3). A change of supplior of a material or stabilisor doos not lead to a change in parformance if the chemical composition remains the same. Material modifications within certain limits are not considered as a change of material. Guidance for these limits can be found in the standards given in Annex B. For tests previously performed in accordance with the provisions of the standards listed in Annex A, or the recognized European specification, as applicable, (same product, same characteristio(s), same test method, same system of attestation ete.) the results may be taken into account. All characteristics given in Clause 4 shall be subject to calculation andior initial type testing, except 4.6.2 where the characteristics of the components used have already been determined by the component manufacturer on the basis of conformity with other product standards. However this does not relieve the manufacturer of the piping system from the responsibility of ensuring that the system conforms to the requirements of this document 6.2.2 _ Initial type test requirements ‘The initial type testing of the characteristics according to Clause 4 shall be performed in accordance with the ‘sampling procedure givan under type tosts (TT) of the applicable product specific standards for assessmant of ‘conformity as glven in Annex B. If the standard does not contain one or more of the characteristics, then testing as given in Table 3 shall apply. For products where no such standard exists Table 3 shall apply. Cepyign Bete Sanda ester, aBS EN 15014:2007 EN 15014:2007 (E) Table 3 — Type testing of pipes and fittings Requirement | Testing clause of this | relevantto # | Sampling procedure Essential characteristics | “European (rinimum sampling) Aooeptance: standard | 1 | w | & Reaction to fre at +P | +2 | — | Oncelcompound or See dasaification in formulation © EN 13501-1 External pressure strength 42 + | + | + | See intemal pressure Passlall ‘strength Internal pressure strength 432 + | + | + One diameterisize group) | Passtfail fitting group/compound or formulation Dimensional olerances a4 + | —| + | Oncelsizertingicampound | Passa fr formulation Tighines of joints 45 + [+ | © | One diametersize groupl | Passa jaint design Durabiiy 46 + | + | * | Onece/compound or By the classification of formulation the long-term strongth performance 2 1 Is initial type test in case of new systam; Ms change of matera EE isextansion of he proc ange wth new size group ar itng grup, + cenotes testng relevant or mo enaractrste-oocutenco- cambio. © only obligatory if subject fo regulatory requirements applicable in the place of use (see also Table ZA 2) © Incase a single buring ters (SB test the verboa par shel be ize 110 and the horzotal part size 40, whieh wl then be representative for all mensions Test reports shall be kept by the manufacturer for at least 10 years after discontinuation of the product. 63. Factory production control 63.4 General The manufacturer shall establish, document and maintain an FPC system to ensure that the products placed (on the market conform to the stated performance characteristics. The FPC system shall consist of procedures, regular inspections and tests and/or assessments and tho uso of tho results to control raw and other incoming ‘materials or components, equipment, the production process and the product. If the manufacturer has the component designed, manufactured, assembled, packed, processed and labelled by ‘subcontracting, FPG of the original manufacturer may be taken into account. However, where subcontracting takes place, the manufacturer shail retain the overall control of the component and ensure that, he receives all the information that is necessary to fulfil his responsibilities according to this European Standard. The manufacturer who subcontracts all of his activities may in no circumstances discharge himself of his responsibilities to a subcontractor. All the elements, requirements and provisions adopted by the manufacturer shall be documented in a systematic manner in the form of written policies and procedures. This production control system documentation shall ensure a commen understanding of conformity evaluation and enable the achievement of the required component characteristics and the effective operation of the production control system to be checked.BS EN 15014:2007 Factory production control therefore brings together operational techniques and all measures allowing maintenance and control of the conformity of the component with its technical specifications. Its implementation may be achieved by controls and tests on raw materials and constituents, processes, manufacturing equipment and finished components, including material properties in components, and by making use of the results thus obtained, The results of inspections, tests or assessments requiring action shall be recorded, as shall any action taken. ‘The action to be taken when control values or criteria are not met shall be recorded and retained for the period ‘specified in the manufacturers FPC procedures. The specifications of all incoming raw materials and components shall be documented, and the inspection ‘scheme for ensuring their conformity shall be established. Manufacturers operating a quality system, which conforms to or is no less stringent than the relevant requirements of EN ISO 9001:2000 and which is made specific to products covered by this European ‘Standard shall be deemed to satisfy the FPC requirements of this European Standard. 6.3.2 FPC requirements ‘The FPC of the characteristics according to Clause 4 shall be performed in accordance with the sampling procedure given under batch release tests (BRT) of the applicable product specific standards for assessment of conformity as given in Annex B. If the standard does not contain one or more of the characteristics, then testing as given in Table 4 shall apply. For products where no such standard exists Table 4 shall apply. Cepyign Bete Sanda ester, iBS EN 15014:2007 EN 15014:2007 (E) Table 4 — Factory production control of pipes and fittings Requirement clause of Sampling procedure oa oratories) ie Test method ‘altunearaingy | Acseptance ‘Standard Reaction to fre # 41 | Ieniifeation of compound or | Onoe’baich See formulation classification in EN 13501-1 Extemal pressure strength 42 | Sosintemaipressure strength | See internal pressure | Pass/fal strength intemal pressure ctrengih | 4.32 | Forthermoplastice products: | Oncerbatch Pasafal EN 180 1167-1 and EN ISO 1167-2, -3, 4 a8 appropriate witha test pressurelstress level related to the wall thickness for pipes and the PN for fitings? For thermosetting products: EN 1304 For multilayer pipes: EN ISO 1167-1 and ENISO 1187-2, -3, 4 a8 appropriate with a test pressure/stress level as speciiog in ISO 21004 Dimensional tolerances 44 | ENISO 3126 or according tothe | Onoe’batch Passi manufacturers quality plan Tightness of joints 45 | Indirect testing: see dimensional | Onoe’batch Passiall tolerances Durability 46 | Indirect testing see intemal | Onoe’baich Passiall pressure strength, and check of ‘compound or formulation (Oni abigaiony/ subject to regulatory requirements appicable in he place of use Ths toot parameters canbe found nthe relovant product standard ghn in Annex A. 6.3.3 FPC system requirements 63.3.1. Personnel Tho responsibilty, authority and the relationship between personnel that manages, performs or verifies work affecting product conformity, shall be defined. This applies in particular to personnel that need to initiate actions preventing product non-conformities from occurring, actions in case of non-conformities and to identify and register product conformity problems. Personnel performing work affecting product conformity shall be competent on the basis of appropriate education, training, skills and experience for which records shall be maintained. 63.3.2 Equipment All weighing, measuring and testing equipment necessary to achieve, or produce evidence of, conformity shall be calibrated or verified and regularly inspected according to documented procedures, frequencies and criteria. Control of monitoring and measuring devices shall comply with the aporopriate clause of EN ISO 9001:2000. ‘All equioment used in the manufacturing process shall be regularly inspected and maintained to ensure use, \Wear or failure does not cause inconsistency in the manufacturing process.BS EN 15014:2007 Inspections and maintenance shall be carried out and recorded in accordance with the manufacturer's written procedures and the records retained for the period defined in the manufacturer's FPC procedures. 6.3.3.3 Design process “The factory production control system shall document the various stages in the design of the products, identify the checking procedure and those individuals responsible forall stages of design. During the design process itself, a record shall be kept of all checks, their results, and any corrective actions taken. This record shall be sufficiently detailed and accurate to demonstrate that all stages of the design phase, and all checks, have been carried out satisfactorily. Compliance with EN ISO 9001:2000, 7.3 shall be deemed to satisfy the requirements of this subclause, 6.3.3.4 Raw materials and components ‘The specifications of all incoming raw materials and components shall be documented, as shall the inspection scheme for ensuring their conformity. The verification of conformity of the raw material with the specification shall be in accordance with EN ISO 9001:2000, 7.4.3. 6.3.3.5 In-process control The manufacturer shall plan and carry out production under controlled conditions. Compliance with EN ISO 9001:2000, 7.5.1 and 7.5.2 shall be deemed to satisfy the requirements of this subclause. 6.3.3.6 Traceability and marking Individual products and product batches shall be identifiable and traceable with regard to their production origin. The manufacturer shall have written procedures ensuring that processes related to affixing traceability codes and/or markings (see ZA.3) are inspected regularly. Compliance with EN SO 9001:2000, 7.5.3 shall be deemed to satisfy the requirements of this subclause. 6.3.3.7 Non-conforming products ‘The manufacturer shall have written procedures which specify how non-conforming products shall be dealt with, Any such events shall be recorded as they occur and these records shall be kept for the period defined in the manufacturer's written procedures. Compliance with EN ISO 9001:2000, 8.3 shall be deemed to satisfy the requirements of this subclause. 6.3.3.8 Corrective action ‘The manufacturer shall have documented procedures that instigate action to eliminate the cause of non- conformities in order to prevent recurrence. Compliance with EN ISO 9001:2000, 8.5.2 shall be deemed to satisfy the requirements of this subclause. 6.3.3.9 Handling, storage and packaging ‘The manufacturer shall have procedures providing methads of product handling and shall provide suitable storage areas preventing damage or deterioration, 6.4 One-off products and products produced in very low quantities Products produced as a one-off and products produced in very low quantities (less than 20 per year) are assessed as follows. For initial type assessment, the provisions of Table 3 apply, with the following exceptions — for reaction to fire the classification of other products made out of the same compound or formulation may be used; Cepyign Bete Sanda ester, a6BS EN 15014:2007 EN 15014:2007 (E) — external and intemal pressure strength shall not be tested. itis assumed that by the defined geomotry this requirement is fulfilled: — durability may not be tested. Nevertheless the manufacturer shall declare the PN of is product according to the geometrical design and the used compound or formulation. ‘The FPC system of one-off products and products produced in very low quantities shall ensure that raw materials and/or components are sufficient for the product; the provisions of Table 4 applying only where appropriate. The manufacturer shall maintain records allowing traceability of the product.BS EN 15014:2007 EN 15014:2007 (E) Annex A (normative) Product standards for buried and above-ground pressure piping systems in plastics materials for water for general purposes, drainage, sewerage, irrigation and other fluids EN 1452-1, Plastics piping systems for water supply — Unplasticized poly(vinyl chloride) (PVC-U) — Part 1: General EN 1452-2, Plastics piping systems for water supply — Unplasticized poly(vinyl chloride) (PVC-U) — Part 2: Pipes EN 1452-3, Plastics piping systems for water supply — Unplasticized poly(vinyl chloride) (PVC-U) — Part 3: Fittings EN 1452-5, Plastics piping systems for water supply — Unplasticized poly(vinyl chloride) (PVC-U) — Part 5: Fitness for purpose of the system EN 1456-1, Plastics piping systems for buried and above ground drainage and sewerage under pressure — Unplasticized poly(vinyl chioride)(PVC-U) — Part 1: Specifications for piping components and the system EN 1796, Plastics piping systems for water supply with or without pressure — Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) EN 12201-1, Plastics piping systems for water supply — Polyethylene (PE) — Part 1: General EN 12201-2, Plastics piping systems for water supply — Polyethylene (PE) — Part 2: Pipes EN 12201-3, Plastics piping systems for water supply — Polyethylene (PE) — Part 3: Fitings EN 12201-5, Plastics piping systems for water supply — Polyethylene (PE) — Part 5: Fitness for purpose of the system EN 13244-1, Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage — Polyethylene (PE) — Part 1: General EN 13244-2, Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage — Polyethylene (PE) — Part 2: Pipes EN 13244-3, Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewarage — Polyethylene (PE) — Part 3: Fittings EN 13244-6, Plastics piping systems for buried and above-ground pressure systems for water for general Purposes, drainage and sewerage — Polyethylene (PE) — Part 5: Fitness for purpose of the system EN 14364, Plastics piping systoms for drainage and sewerage with or without pressure — Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) — Specifications for pipes, fittings ‘and joints EN ISO 10931, Plastics piping systems for industrial applications — Poly(vinylidene fluoride) (PVDF) - ‘Specifications for components and the system (ISO 10931:2005) Cepyign Bete Sanda ester, a;BS EN 15014:2007 EN 15014:2007 (E) EN ISO 15493, Plastics piping systems for industrial applications — Acryionitrle-butadiene-styrene (ABS), unplasticized poly(vinyl chloride) (PVC-UN) and chlorinated poly(vinyl chloride) (PVC-C) — Specifications for components and the system — Metric series (ISO 15493:2003) EN ISO 15494, Plastics piping systems for industrial applications — Polybutene (PB), polyethylene (PE), polypropylene (PP) — Specifications for components and the system — Metric series (ISO 15494:2003) 1S0 8779, Polyethylene (PE) pipes for irigation laterals — Specifications ISO 9625, Mechanical join ftings for use with polyethylene pressure pipes for irigation purposes ISO 10467, Plastics piping systems for pressure and non-pressure drainage and sewerage — Glass- reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin ISO 10639, Plastics piping systems for pressure and non-pressure water supply — Glass~einforced thermosstting plastics (GRP) systems based on unsaturated polyester (UP) resin ISO 14236, Plastics pipes and fitings — Mechanical-joint compression fittings for use with polyethylene prossure pipes in water supply systems ISO 16422, Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-0) for the conveyance of water under pressure — Spectfications ISO 21004, Plastics piping systems — Muttilayer pipes and thoir joints, based on thermoplastics, for water supply NOTE This listing represents the situation at the time this document was published. It can be amended once new standards are develoned.BS EN 15014:2007 EN 15014:2007 (E) Annex B (normative) Standards for assessment of conformity for buried and above-ground pressure piping systems in plastics materials for water for general purposes, drainage, sewerage, irrigation and other flui This annex is normative as far as the assessment of conformity information contained in the listed standards and referred to in Clause 6 for the essential characteristics is concerned. Otherwise it has the status of an informative annex. ENV 1452-7:2000, Plastics piping systems for water supply — Unplasticized poly(vinyl chloride) (PVC-U) — Part 7: Guidance for the assessment of conformity CEN/TS 1456-2:2003, Plastics piping systems for buried and above-ground drainage and sewerage under pressure — Unplasticized poly(vinyl chioride) (PVG-U) — Part 2: Guidance for the assessment of conformity CEN/TS 12201-7:2003, Plastics piping systems for water supply — Polyethylene (PE) — Part 7: Guidance for the assessment of conformity CENITS 13244-7:2003, Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage — Polyethylene (PE) — Part 7: Guidance for the assessment of conformity CEN/TS 14832:2006, Plastics piping systems for drainage, sewerage and water supply, pressure and non- pressure — Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) — Guidance for the assessment of conformity NOTE This listing represents the situation at the fime this document was published. It can be amended once new standards are developed. 19BS EN 15014:2007 EN 15014:2007 (E) Annex ZA (informative) Clauses of this European Standard addressing the provisions of EU Construction Products Directive ZA Scope and relevant characteristics This European Standard has been prepared under Mandate M/131 "Pipes, tanks and ancillaries not in contact with water intended for human consumption" given to CEN by the European Commission and the European Froo Trade Association. Tho clauses of this European Standard shown in this annex meet the requirements of the mandate given under the EU Construction Products Directive (89/106/EEC). ‘Compliance with these clauses confers a presumption of fitness of the construction products covered by this annex for their intended uses indicated herein; reference shall be made to the information accompanying the CE marking. WARNING: Other requirements and other EU Directives, not affecting the fitness for intended use, can be applicable to the construction products falling within the scope of this European Standard, NOTE 1 In addition to any apectic c'auses relating to dangerous substances contained in this standard, there may be| ‘ther requirements applicable to the products falling within iis scope (e.g. transposed European legislation and national laws, regulations and administratve provisions). In order to meat the provisions of the EU Construction Products Directive, these requirements need also to be complied wit, when and where they apply. NOTE 2 _ Aninformative database of European and national provisions on dangerous‘regulated substances is available at the Construction web site on EUROPA (accessed through hitp:/europa, eu inticomm/enterprise/construction/intemal/sangsub/dangmain. him), This annex has the same scope as Clause 1 of this standard with regard to the products covered. It establishes the conditions for the CE marking of pipes and fittings made of plastics materials intended for the use indicated in Table ZA.1 and shows the relevant clauses applicable.BS EN 15014:2007 Table ZA.1 — Relevant clauses Construction Product: Pipes and fittings made of plastics materials Intended uses: Buried or above-ground conveyance of drainage, sewerage and non-dtinkin water under pressure; vacuum-operated soil and waste conveyance Essential characteristics Requirement | Levels Notes clauses of this | and/or standard classes Reaetion to fire 44 AtoF | See classification in EN 13501-1 Extomal pressure strength 42 none _| Pass/fail Internal pressure strength 432 none _| Passiail Dimensional tolerances 44 none _| Pass/fail Tightness: Air and liquid 45 none _| Pass/fail Durability 46 none | Classification of long-term strength performance The requirement on a certain characteristic is not applicable in those Member States (MSs) where there are no regulatory requirements on that characteristic for the intended end use of the product. In this case, manufacturers placing their products on the market of these MSs are not obliged to determine nor dectara the performance of their products with ragard to this characteristic and the option “No performance determined” (NPD) in the information accompanying the GE marking (see ZA.3) may be used. ZA2 Procedure for attestation of conformity of plastics pipes and fittings ZA2.1 Systems of attestation of conformity ‘The systems of attestation of conformity of plastics pipes and fittings indicated in Table ZA.1, in accordance with the Decision of the European Commission (1999/472/EC and amendment 2001/596/EC) as given in ‘Annex Ill of the mandate M/131 for pipes, tanks and ancillaries not in contact with water intended for human ‘consumption, is shown in Table ZA.2 for the indicated intended uses and relevant levels or classes. Cepyign Bete Sanda ester, aBS EN 15014:2007 EN 15014:2007 (E) Table ZA.2 — Systems of attestation of conformity Attestation of Products Intended uses Levels or classes ‘conformity systems 5 42, BM and cl a Above-ground pressure pioing | A1"?, 42”, 8 and C! 1 systems inside building subject | 442) 9% B® C®, D and E 5x to reaction to fire regulations Pipes, fittings (At to E) and FE 4a and their joints Buried or above-ground pressure piping systems not None aa subject to fire regulations “T Broductsimaterials for which a clearly Kenifable stage in the production process resuls in an improvement of the reaction to fre classification (e.9. an addon of fire retardants or aiming of organie mater). ©! Products/matarials not covered by fooknota '°! Progucts/materials that do not requite to be tested for reaction to fire (e.g. products/materials of Class AY according to Commission Decision S6/603/EC, as amended) System f: See Directive B9/106/EEG (CPD) Annex I? (i), without audit testing of samples. ‘System 3: See Directive 89/{0G/EEC (CPD) Annex Il (i, second possibily System 4: See Directive 88/106/EEC (CPD) Annex I. (i), hid possibilty. ‘Tho attestation of conformity of plastics pipes and fitings indicated in Table ZA.1 shall be according to the evaluation of conformity procedures indicated in Table ZA.3, Table ZA4 or Table ZA5, as applicable, resulting from the application of the clauses of this European Standard indicated therein. Table ZA.3 — Assignment of evaluation of conformity tasks for pipes, fittings and their joints under system 1 Evaluation of conformity Tasks Content of task Meieee oooh 5 Parameters related to all Gee declared characteristics of 63 “Tasks under the Sabie 2A responsibility of the manufacturer Except for ‘reaction to firs’, Initial type testing —_| all declared characteristios 62 of Table ZA.1 Task under the | Factory production | 5 feaction to fire 63 responsibility of | control (FPC) the notified body | jnitial typo testing Reaction to fire 6.2 NOTE The factory production control procedures for reaction to fie fo be earied oul by the manufacturer may ‘be determined by agreement withthe notified body.BS EN 15014:2007 Table ZA.4— Assignment of evaluation of conformity tasks for pipes, fittings and their joints under system 3 Evaluation of Tasks Content of task conformity clauses to apply Parameters related to all Factory production | declared characteristics of 63 control (FPC) ead Tasks under the Except for ‘reaction to fre", responsibilty of | intial type testing —_| all declared characteristics of 62 the manufacturer Table ZA1 Initial type testing by | Reaction to fre a notified body 62 (laboratory) Table ZA.5 — Assignment of evaluation of conformity tasks for pipes, fittings and their joints under system 4 Tasks Content of task Evaluation of conformity clauses to apply Parameters related to all Factor production | dectared characteristics of 63 Tasks for the control (FPC) Table ZA4 manufacturer ¥ ‘ All declared charactaristcs of Initial type testing — | PASE 62 ZA22 EC Certificate and Declaration of conformity In case of products with system 1: When compliance with the conditions of this annex is achieved, the certification body shall draw up a certificate of conformity (EC Certificate of conformity), which entitles the manufacturer to affix the CE marking. The certificate shall include: name, address and identification number of the certification body; authorised representative established in the BEA, and name and address of the manufacturer, or place of production; NOTE 1 The manufacturer may also be the person responsible for placing the product onto the EEA market, if he takes responsibilty for CE marking, description of the product (type, identification, use, ...) provisions to which the product conforms (i.e. Annex ZA of this EN); particular conditions applicable to the use of the product (e.g. provisions for use under certain conditions); number of the certificate; conditions and period of validity of the certificate, where applicable; ‘name of, and position held by, the person empowered to sign the certificate,BS EN 15014:2007 EN 15014:2007 (E) In addition, the manufacturer shall draw up and retain a declaration of conformity (EC Declaration of conformity) including the following: — name and address of the manufacturer, or his authorised representative established in the EEA; — name and address of the certification bedy; — description of the product (Iype, identification, use, ...), and a copy of the information accompanying the CE mark NOTE 2 Where some of the information required for the declaration ls already given in the CE marking information, it does not need to be repeated — provisions to which the product conforms (.0. Annex ZA of this EN), and a reference to the initial type test report(s) and factory production control records (if appropriate); — particular conditions applicable to the use of the product (if necessary); — number of the accompanying EC Certificate of conformity, — name of, and position held by, the person empowered to sign the declaration on behalf of the manufacturer or of his authorised representative. In case of products under system 3: When compliance with the conditions of this annex is achieved, the manufacturer or his agent established in the EEA shall draw up and retain 2 declaration of conformity (EC Deciaration of conformity), which entities the manufacturer to affix the CE marking, This declaration shall include: — name and address of the manufacturer, or his authorised representative established in the EEA, and place of production; NOTES The manufacturer may also be the person responsible for placing the product onto the EEA market, if he takes responsibilty for CE marking — description of the product (type. identification, us CE marking: NOTE 4 Where some of the information required for the declaration is already given in the CE marking information, it does not need to be repested — provisions to which the product conforms (1.2. Annex ZA of this EN), and a reference to the initial type test report(s) and factory production control records (if appropriate); |. and 2 copy of the information accompanying the — particular conditions applicable to the use of the product, (if necessary); — name and address of the notified laboratory(ies); — name of, and position held by. the parson empowored to sign the declaration on behalf of the manufacturer or his authorised representative. In case of products under system 4: When compliance with this annex is achieved, the manufacturer or his agent established in the EEA shall draw up and retain @ declaration of conformity (EC Declaration of conformity), which entitles the manufacturer to affix the CE marking. This declaration shall include: — name and address of the manufacturer, or his authorised representative established in the EEA, and place of production; NOTES The manufacturer may also be the person responsible for placing the product onto the EEA market, if he takes responsibilty for CE marking — description of the product (type, identification, use... CE marking: NOTE 6 Where some of the information required for the daciaration is already given in the CE marking information, tdoes not need to be repeated. and a copy of the information accompanying theBS EN 15014:2007 — provisions to which the product conforms (i.e. Annex ZA of this EN); — particular conditions applicable to the use of the product (if necessary); — name of, and position held by, the person empowered to sign the declaration on behalf of the manufacturer or of his authorised representative. The above mentioned declaration and cerifcate shall be presented in theofficial language(s) or language(s) accepted in the Member State in which the product is to be used. NOTE 7 Duplication of information between the declaration and certificates should be avoided. To avoid duplication of information, cross-reference between documents may be made when one contains more information than the other. 2A.3. CE marking and labelling ZA3.1_ CE marking requirements ‘The manufacturer or his authorised representative established within the EEA is responsible for the affixing of the CE-marking. The CE-marking symbol to affix shall be in accordance with Directive 93/68/EEC and shall be shown on the pipes and fittings, or it may be on the accompanying label or on the packaging or on the ‘accompanying commercial documents eg. a delivery note. The GE marking symbol may be placed alone on the product. If this option is used the CE marking symbol shall appear again in another location including the information as required in ZA.3.1 or ZA.3.2, as applicable. The following information shall accompany the CE marking symbol (where relevant): — identification number of the certification body (only for products under system 1); — name or identifying mark of the manufacturer (see NOTE 1 in ZA.2.2); — number of the EC Certificate of conformity (only for products under system 1); — last two digits of the year in which the CE marking was affixed; — reference to this European Standard; — description of the product: generic name, material, dimensions, ... and intended use (may be by code or by reference to a specification); — information on those relevant essential characteristics listed in Table ZA.1 which are to be declared: — declared values and, where relevant, level or class (including “pass” for pass/fail requirements, where necessary) to declare for each essential characteristic as indicated in "Notes" in Table ZA.1; — “No performance determined for characteristics where this is relevant; — as an alternative, a standard designation which shows some or all of the relevant characteristics (where the designation covers only some characteristics, it will need to be supplemented with declared values for other characteristics as above). The "No performance determined” NPD option may not be used where the characteristic is subject to a threshold level. Otherwise, the NPD option may be used when and where the characteristic, for a given intended use, is not subject to regulatory requirements in the Member State of destination Figure ZA.1 gives an example of the information to be given on the product, label, packaging and/or ‘commercial documents,BS EN 15014:2007 EN 15014:2007 (E) cE 01234 ‘AnyCo Ltd., PO Box 21, B-1050 Brussels 07 01234-CPD-00234 |€ CE conformity marking, consisting ofthe ‘CE"-symbol given fn Directive SS/5B/EEC. ‘© lcentiteatton numberof the cetiicaton bedy (where relavant, see NOTE“) “€ Name or identifying matt and registered addreae ofthe manufacturer ‘© Loot two ais of no yoarin whien tna marking was attired ‘© Conticate number (where relevant, see NOTE 2) EN 15014 |€ Number of this European Standard Pipe of PVC-U /€ Name and mate DN 250-PN 10 “€ Dimension and pressure class P ‘€ Intended use (may be by cose or by reference toa specication), For guidance se= CEN/TR 15428-2007 [1] Reaction to fre F ‘€ Information on reguated characteristios External pressure strength Pass Internal pressure strength Pass Dimensional tolerances (EN 1452.2) Pass Tightness of joints Pass Durability Pass Figure ZA.1 — Example of CE marking Information NOTE 1 — The identification of the notified body is only relevant for systems 1 NOTE2 — Reference to the Cerliicale number can only be made under systems 4 In addition to any specific information relating to dangerous substances, the product should also be accompanied, when and where required and in the appropriate form, by documentation listing any other legislation on dangerous substances for which compliance is claimed, together with any information required by that legislation, NOTE European legislation without national derogations need not be mentioned. ZA.3.2. Simplified CE marking with reference to a web site ZA321 General In situations when a manufacturer wants to use a web site to provide the information required for CE marking as given in ZA.3.1 then a simplified CE marking may be used and affixed on the product itself, on a label attached to it, on its packaging or on the accompanying commercial documents. ‘Such simplified CE marking shall contain all information mentioned in ZA.3.1 except the information on relevant essential characteristics listed in Table ZA.1. Instead of this list of characteristics an unambiguous reference shall be used allowing the deciared performances for this specific product to be obtained. The minimum rules for the proper use of a web site for the CE marking, complementing the simplified CE marking information are given in ZA.3.2.2. ‘These references shall be: — address of a web site providing the information on the characteristics;BS EN 15014:2007 EN 15014:2007 (E) — unique, unambiguous reference, permitting the retrieval of the complete information required in ZA3.1 belonging to the product to which the simplified CE marking is affixed. When products are modified leading to changes in performances, this shall be clearly identifiable. In addition the following minimum information shall be specified on the simplified CE marking (where relevant): — identification number of the certification body (only for products under system 1); — name or identifying mark of the manufacturer (see NOTE 1 in ZA.2.2); — number of the EC Certificate of conformity (only for products under system 1); — last two digits of the year in which the CE marking was affixed; — reference to this European Standard; — material (may be by code or by reference to @ specification), — dimensions; — declared performance of the product: strength, level or class (where relevant); — intended use (may be in codified format or by reference to a product specification eto.); Figure ZA.2 gives an example of the short format information to be given on the product, label, packaging and/or commercial documents. Directive SX168/EEC. 07234 € Identication numberof the oertfcation body (where relevant, see NOTE 1) “AnyCo Lid © Name or idanttying mak of the manufacturer 07 Last two gis of the yearn which the marking was affixed 01234.cPD.00234 CConticate number (whore relovant, 600 NOTE 2) EN 15014 “€ Number ofthis European Standord Pipe of PVC-U ]& Name ans material DN 250-PN 10 J Dimension and pressure lass P |& Intended use (may be by cove or by reference to @ specication). For guidance see CENITR 15436:2007 [1] wwrw_anyco.com/ee![Tracking reference] | € Accurate unique, unambiguous reference to the part ofthe wobete ‘where the characteristics of Table ZA 1 are given (see NOTE 3) Figure ZA.2 — Example of CE marking information with a link to a web site NOTE 1 The Identification ofthe notified bosy is only relevant for systems 1. NOTE 2 Reference to the Certificate number can only be made under systems 1 NOTES The tracking reference can be by reference to e.g. "Catalogue 2007/1" or "Cade and Batch number" of the product eto. It is up to the manufacturar to define its tracking reference of the product. In addition to any specific information relating to dangerous substances, the product should also be accompanied, when and where required and in the appropriate form, by documentation listing any other legislation on dangerous substances for which compliance is claimed, together with any information required by that legistation. NOTE 4 — European legislation without national deragations need not be mentioned.BS EN 15014:2007 EN 15014:2007 (E) ZA322 imum rules for the proper use of a web site for CE marking information When the conditions set in ZA.3.2.1 are met, the requirements permiting the use of a web site should comply with the following provisions: with the unique, unambiguous reference given on the simplified label for CE marking, the complete CE ‘marking information as given in ZA.3.1 for this specific product shall be provided; web site information on CE marking shall be suitably protected, preventing modification of data by extemal parties; web site information shall be dated; as far as the unique, unambiguous reference of the product is concerned the information shown on the simplified version of the CE marking shall be at all times coherent with the information on the web site. Changes to the CE marking information on the web site shall be reflected by a new unique, unambiguous reference of the product and consequently by a new simplified CE marking: web site shall allow printing the data. The print outs shall clearly reproduce all data accompanying the CE symbol as given in ZA.3.1 and the web site address; ‘access to web sites, which shall allow consultation with all possible intemet browsers, shall be available atall times (except for short maintenance periods); web site data management shall be subject to a manufacturer's procedure, ensuring that intemal responsibilities as regards the data on the website are laid down.BS EN 15014:2007 EN 15014:2007 (E) Bibliography [1] GEN/TR 15438:2007, Plastios piping systems — Guidance for coding of products and their intended uses [2] prEN 15389:2005, industrial valves — Performance characteristics of thermoplastic valves when used a8 construction products [3] EN ISO 16135, Industrial vaives —Ball valves of thermoplastics materials (ISO 16136:2006) [4] EN ISO 16136, Industrial valves — Butterfly valves of thermoplastic materials (ISO 16136:2006) [5] EN1SO 16137, industrial valves —_Check vaives of thermoplastic materials (ISO 16137:2006) [5] EN1SO 16138, Industria! valves — Diaphragm valves of thermoplastic materials (ISO 16138:2006) [7] EN ISO 16139, Industrial valves — Gate valves of thermoplastic materials (ISO 16139:2006) [8] EN1S021787, Industria! valves — Globe valves of thermoplastic materials (ISO 21787:2008) [9] _EN 1452-4, Plastics piping systems for water supply — Unpiasticized poly(viny! chloride) (PVC-U) — Part 4: Valves and ancillary equipment [10] EN 1201-4, Plastics piping systems for water supply — Polyethylene (PE) — Part 4: Valves [11] EN 13244-4, Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage — Polyethylene (PE) — Part 4: Valves [12] EN 1452.2, Plastics piping systems for water supply — Unplasticized poly(vinyl chloride) (PVC-U) — Part 2: Pipes [13] EN 1778, Characteristic values for welded thermoplastic constructions — Determination of allowable stresses and modul for design of thermoplastics equioment [14] ISO 13761, Plastics pipes and fittings — Pressure reduction factors for polyethylene pipeline systems for use at temperature above 20 °CBS EN 15014:2007 National Annex NA (informative) Produet standards used in conjunction with this standard ‘BS 5891-1:2008 Acrylonitrile-butadiene styrene (ABS) pressure pipe ~ Part 1: Specification BS 5892-1:2008 Acrylonitrile-butadiene styrene (ABS) fittings jor use with ABS pressure pipe ~ Part 1: Specification BS EN 1452 Plastics piping sysiems for water supply ~ Unplasticized poly(vinyl ehloride) (PVC-U) — Part 1; General, Part 2: Pipes, Part 3: Fittings, Part &: Fitness for purpose of the system BS EN 1456-1 Plasties piping systems for buried and above ground drainage and sewerage under pressure Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for piping components and the system BS EN 1796 Plastics piping systems for water supply with or without pressure ~ Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) BS EN 12201 Plastics piping systems for water supply - Polyethylene (PE) ~ Part 1: General, Part 2: Pipes, Part &: Fittings, Part 5: Fitness for purpose of the system BS EN 18244 Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage ~ Polyethylene (PE) Part 1: General, Part 2: Pipes, Part 3: Fittings, Part 5: Fitness for purpose of the system BS EN 14364 Plastics piping systems for drainage and sewerage with or without pressure Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) BS EN ISO 10981 Plastics piping systems for industrial applications ~ Poly(vinylidene fluoride) (PVDF) — Specifications for components and the system BS EN ISO 15493 Plasties piping systems for industrial applications ~ Aerylonitrile-butadiene-styrene (ABS), unplasticized poly(vinyl Chloride) (PVC-U) and chlorinated poly(vinyl chloride) (PVC-C) ~ Specifications for components and piping systems — Metric series BS EN ISO 15494 Plasties piping aystems for industrial applications - Polybutylene (PB). polyethylene (PB) polypropylene (PP) ~ Specifications for components and piping systems — Metric series 180 8779 Polyethylene (PE) pipes for irrigation laterals ~ Specifications 180 9625 Mechanical join fittings for use with polyethylene pressure pipes for irrigation purposes 180 10467 Plastics piping systems for non-pressure drainage and sewerage~ Glass-reinforeed thermosetting plastics (GRP) based on unsaturated polyester resin (UP) 180 10689 Plastics piping systems for pressure and non-pressure water supply ~ Glass-reinforced thermosetting plasties (GRP) based on unsaturated polyester resin (UP) 180 14286 Plastics pipes and fittings ~ Mechanical-joint compression fittings for use with polyethylene pressure pipes in water supply systems 180 16422 Pipes and joints made of orientated unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water ~ Specifications 80 21004 Plasties piping systems ~ Multilayer pipes and their joints, based on thermoplastics, for water supply NOTH This lini represents the situation atthe time this document was published, cent sunt sen, © BSI 2008enone Suns a, blankBS EN 15014:2007 BSI 889 Chiswick High Road London Wa 4aL BSI — British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter Revisions British Standards are updated by amendment or revision, Users of British Standards should make sure that they possess the latest amendments or editions, It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front caver. ‘Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards, Buying standards ‘Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: [email protected]. Standards are also available from the BSI wobsite at http//svww.bsi-global.com. In response to orders for international standards, it is BST policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. ‘Tel: +44 (0)20 $996 7111. Fax: +44 (0)20 8996 7048. Email: [email protected]. Subseribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration, Tol: +44 (0)20 8996 7002. Fax: +414 (0)20 8996 7001. Email: [email protected]. Information regarding online access to British Standards via British Standards Online can be found at http://www.bsi-global com/bsonline. Further information about BSI is available on the BSI website at httnusvwrw.bsi-global.com. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the ‘UK, of the publications of the international standardization bodies. Exeopt as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronie, photocopying, recording o atherwise — without prior written permission from BSI. ‘This does not preclude the free use, in the course of implementing the standard, ofnecessary details such as symbols, and size, type or grade designations. If these details are to he used for any other purpose than implementation then the prior ‘written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. ‘Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7Aa3. Email: [email protected].