Scribd
Upload
59 views3 pages

VLAN and Routing Configuration Guide

The document contains configuration commands for routers R1, S1 and HQ. R1 is configured with subinterfaces on GigabitEthernet 0/0 with encapsulation dot1Q and IP addresses for VLANs 10, 20, 30, 88 and 99. S1 has GigabitEthernet 0/1 configured as a trunk port with native VLAN 99. HQ routes IP networks for VLANs 10, 20, 30 and 88 over serial interface S0/0/0 and routes the 209.165.200.0 network with a gateway over S0/1/0.

Uploaded by

Imam Mutaqin
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
59 views3 pages

VLAN and Routing Configuration Guide

The document contains configuration commands for routers R1, S1 and HQ. R1 is configured with subinterfaces on GigabitEthernet 0/0 with encapsulation dot1Q and IP addresses for VLANs 10, 20, 30, 88 and 99. S1 has GigabitEthernet 0/1 configured as a trunk port with native VLAN 99. HQ routes IP networks for VLANs 10, 20, 30 and 88 over serial interface S0/0/0 and routes the 209.165.200.0 network with a gateway over S0/1/0.

Uploaded by

Imam Mutaqin
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

R1>en

R1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R1(config)#int g0/0.10
R1(config-subif)#encap
R1(config-subif)#encapsulation dot
R1(config-subif)#encapsulation dot1Q 10
R1(config-subif)#ip address 172.31.10.1 255.255.255.0
R1(config-subif)#int g0/0.20
R1(config-subif)#encapsulation dot1Q 20
R1(config-subif)#ip address 172.31.20.1 255.255.255.0
R1(config-subif)#int g0/0.30
R1(config-subif)#encapsulation dot1Q 30
R1(config-subif)#ip address 172.31.30.1 255.255.255.0
R1(config-subif)#int g0/0.88
R1(config-subif)#encapsulation dot1Q 88
R1(config-subif)#ip address 172.31.88.1 255.255.255.0
R1(config-subif)#int g0/0.99
R1(config-subif)#encapsulation dot1Q 99 native
R1(config-subif)#ip address 172.31.99.1 255.255.255.0
R1(config-subif)#exit
R1(config)#int g0/0
R1(config-if)#no sh

S1>en
S1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
S1(config)#ex
S1#
%SYS-5-CONFIG_I: Configured from console by console
S1#sh run
Building configuration...
!
!
!
end
S1#sh vlan brief
S1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
S1(config)#int g0/1
S1(config-if)#sw
S1(config-if)#switchport mode trunk

S1(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to
down

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to


up

S1(config-if)#switchport trunk native vlan 99


S1(config-if)#end
S1#
%SYS-5-CONFIG_I: Configured from console by console
S1#
HQ>en
HQ#conf t
Enter configuration commands, one per line. End with CNTL/Z.
HQ(config)#ip route 172.31.10.0 255.255.255.0 s0/0/0
%Default route without gateway, if not a point-to-point interface, may impact performance
HQ(config)#ip route 172.31.20.0 255.255.255.0 s0/0/0
%Default route without gateway, if not a point-to-point interface, may impact performance
HQ(config)#ip route 172.31.30.0 255.255.255.0 s0/0/0
%Default route without gateway, if not a point-to-point interface, may impact performance
HQ(config)#ip route 172.31.88.0 255.255.255.0 s0/0/0
%Default route without gateway, if not a point-to-point interface, may impact performance
HQ(config)#ip route 209.165.200.30 255.255.255.224 s0/1/0
%Default route without gateway, if not a point-to-point interface, may impact performance
%Inconsistent address and mask
HQ(config)#ip route 209.165.200.0 255.255.255.224 s0/1/0
%Default route without gateway, if not a point-to-point interface, may impact performance
HQ(config)#ip route 209.165.200.0 255.255.255.224 s0/1/1 10
HQ(config)#
R1>en
R1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R1(config)#ip route 0.0.0.0 0.0.0.0 s0/0/0
%Default route without gateway, if not a point-to-point interface, may impact performance
R1(config)#

You might also like