Scribd
Upload
71 views4 pages

AS 3600-2009 Ex002

This document provides an example of checking the demand-to-capacity ratio for an axially loaded rectangular reinforced concrete column. It describes the column geometry, material properties, loads, and reinforcement. Hand calculations are shown to determine the column capacity and compare it to the demand from a given axial load and moment. The results from a structural analysis software program, SAP2000, are also presented and compared to the independent hand calculation, showing good agreement.

Uploaded by

Antonius Ajalah
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
71 views4 pages

AS 3600-2009 Ex002

This document provides an example of checking the demand-to-capacity ratio for an axially loaded rectangular reinforced concrete column. It describes the column geometry, material properties, loads, and reinforcement. Hand calculations are shown to determine the column capacity and compare it to the demand from a given axial load and moment. The results from a structural analysis software program, SAP2000, are also presented and compared to the independent hand calculation, showing good agreement.

Uploaded by

Antonius Ajalah
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Software Verification

PROGRAM NAME: SAP2000


REVISION NO.: 0

AS 3600-2009 Example 002


P-M INTERACTION CHECK FOR COMPRESSION-CONTROLLED RECTANGULAR COLUMN

EXAMPLE DESCRIPTION
The Demand/Capacity ratio for a given axial loading and moment is tested in this
example.

In this example, a reinforced concrete column is subjected to factored axial load


N = 1733 kN and moment My = 433 kN-m. This column is reinforced with five
25M bars. The design capacity ratio is checked by hand calculations and the
result is compared with computed results. The column is designed as a short,
non-sway member.

GEOMETRY, PROPERTIES AND LOADING


1733 kN

My= 433 kN-m


550mm

A A 60 mm 350mm
3m

Section A-A

Material Properties Section Properties Design Properties

Ec = 25x106 kN/m2 b = 350 m fcu = 30 MPa


= 0.2 d = 490 mm fy = 460 MPa
G = 10416666.7kN/m2

AS 3600-2009 Example 002 - 1


Software Verification
PROGRAM NAME: SAP2000
REVISION NO.: 0

TECHNICAL FEATURES TESTED


Tied reinforced concrete column design

RESULTS COMPARISON
Independent results are hand calculated and compared.

Percent
Output Parameter SAP2000 Independent Difference

Column Demand/Capacity Ratio 1.001 1.00 0.1%

COMPUTER FILE: AS 3600-2009 EX002

CONCLUSION
The computed results show an acceptable comparison with the independent
results.

AS 3600-2009 Example 002 - 2


Software Verification
PROGRAM NAME: SAP2000
REVISION NO.: 0

HAND CALCULATION

COLUMN STRENGTH UNDER COMPRESSION CONTROL


fcu = 30 MPa fy = 460 MPa
b = 350 mm d = 490 mm

1) Because e = 250 mm < (2/3)d = 327 mm, assume compression failure. This
assumption will be checked later. Calculate the distance to the neutral axis for a
balanced condition, cb:
Position of neutral axis at balance condition:
600 600
cb = dt = ( 490 ) = 277.4 mm
600 + f y 600 + 460

2) From the equation of equilibrium:


N = Cc + C s T
where
= Cc =
2 fc ab 0.85 30 =
350a 8925a
Cs = As ( f y 2 fc) = 2500 ( 460 0.85 30 ) = 1, 086, 250 N
Assume compression steel yields, (this assumption will be checked later).
T = As f = 2500 f s = 2500 f s ( f s < f y )
N1 =
8925a + 1.086, 250 2500 fs (Eqn. 1)

3) Taking moments about As:


1 a
=
N2 Cc d + C s ( d d )
e 2
The plastic centroid is at the center of the section and d = 215 mm
e =e + d =250 + 215 =465 mm
1 a
=N 8925a 490 + 1, 086, 250 ( 490 60 )
465 2

N = 9404.8a 9.597 a 2 + 1, 004, 489 (Eqn. 2)

AS 3600-2009 Example 002 - 3


Software Verification
PROGRAM NAME: SAP2000
REVISION NO.: 0

4) Assume c = 333.9 mm, which exceeds cb (296 mm).


= =
a 0.84 333.9 280.5 mm
Substitute in Eqn. 2:

N 2 = 8925 280.5 9.597 ( 280.5 ) + 1, 004, 489= 2,888, 240 N


2

5) Calculate fs from the strain diagram when c = 365 mm.


490 333.9
=fs = 600 280.5 MPa
333.9
s =t =fs Es = 0.0014

6) Substitute a = 280.5 mm and fs = 280.5 MPa in Eqn. 1 to calculate N1:


N1= 8925 ( 280.5 ) + 1, 086, 250 2500 ( 280.5 )= 2,887,373 N
which is very close to the calculated N2 of 2,888,240 (less than 1% difference)
250
= Ne
M = 2888 = 722 kN-m
1000

7) Check if compression steel yields. From strain diagram,


333.9 60
=s ( 0.003
= ) 0.0025=
> y 0.0023
333.9
Compression steel yields, as assumed.

8) Therefore, section capacity is


N = 2888 =
1733 kN
e 250
M = 2888 = 0.60 2888 = 433 kN-m
1000 1000

AS 3600-2009 Example 002 - 4

You might also like