Electrotechnical standards relevant for the oil and gas industry / 1

REPORT MARCH
530 2015

Electrotechnical standards relevant for

the oil and gas industry
 Electrotechnical standards relevant for the oil and gas industry / 2

Contents

Contents 2

Acknowledgement 3

Disclaimer 3

Copyright notice 3

Introduction 4

Purpose of report 5

Abbreviations 6

IEC standards specific to the oil and gas industry 8

IEC standards relevant for the oil and gas industry 9

API Standards 50

IEEE (PCIC) Standards 51

NEMA National Electrical Manufacturers Association 58

NFPA codes & standards 61

EEMUA publications 62

UL standards 63

Classification societys standards 66

Energy Institute documents 67

EN standards 68

GSO Electrotechnical standards 71

Other relevant codes, documents & standards 72

 Electrotechnical standards relevant for the oil and gas industry / 3

Acknowledgement
This report was developed by the IOGP Electrical Standards Subcommittee.

Disclaimer
Whilst every effort has been made to ensure the accuracy of the information contained in this
publication, neither IOGP nor any of its Members past present or future warrants its accuracy or
will, regardless of its or their negligence, assume liability for any foreseeable or unforeseeable use
made thereof, which liability is hereby excluded. Consequently, such use is at the recipient's own
risk on the basis that any use by the recipient constitutes agreement to the terms of this disclaimer.
The recipient is obliged to inform any subsequent recipient of such terms.

Copyright notice
The contents of these pages are International Association of Oil & Gas Producers. Permission is
given to reproduce this report in whole or in part provided (i) that the copyright of IOGP and (ii) the
source are acknowledged. All other rights are reserved. Any other use requires the prior written
permission of IOGP.

These Terms and Conditions shall be governed by and construed in accordance with the laws of
England and Wales. Disputes arising here from shall be exclusively subject to the jurisdiction of the
courts of England and Wales.
 Electrotechnical standards relevant for the oil and gas industry / 4

Introduction
The International Association of Oil & Gas Producers (IOGP) organized a workshop 1011 May
2012, in London, within the scope of electrical standards and practices for the oil and gas industry
for electrical technology specialists of IOGP Members and invited guests.

The objectives of the workshop were to:

arrange for global networking amongst the specialists

review and discuss the available standards for electrical installations, ongoing standards
work and existing company specifications related to this discipline

evaluate the needs for improvements of available industry, national or regional standards or
company specifications and harmonization with international standards in this area

evaluate the need for new electrical standards work in the oil and gas industry

share company and/or personal experience regarding electrical installations, standards and
practices.

Within the goal for the workshop was also to identify and prioritize improvements to available
standards or the need for new international (IEC) standards in the electrical area for the benefit of
the global oil and gas industry.

A draft of this report was initially prepared as a basis for this workshop and, following input from
this workshop, IOGP has established the Electrical Standards Subcommittee with the same
objectives as for the workshop. The Subcommittee has subsequently agreed to complete this
document as an IOGP reference report including input from its Members and a benchmarking
exercise in 2013.

This report should be seen in conjunction with the following IOGP reports:

Report 362, Catalogue of international standards used in the petroleum and natural gas
industries (February 2012) where a number of IEC standards are identified

Report 381, Position paper on the development and use of international standards (March
2010) outlining the importance of IEC standards

Report 426, Regulators use of standards (March 2010) including some references to IEC
standards

Report 450, Benchmarking on the use of internal technical specifications and external
standards by some oil & gas companies (February 2011).
 Electrotechnical standards relevant for the oil and gas industry / 5

Purpose of report
The purpose of this report is to provide a list of some of the available and relevant international,
regional, national and industry electrotechnical standards for the oil and gas industries as seen by
the participants of the IOGP Electrical Standards Subcommittee. This report is not exhaustive in
any way and there may well be other relevant electrotechnical standards for the oil and gas
industries.
 Electrotechnical standards relevant for the oil and gas industry / 6

Abbreviations
API American Petroleum Institute

ABS American Bureau of Shipping

BV Bureau Veritas

CRE Committee of Refining Equipment (under API)

CSA Canadian Standards Association

C-NLOPB Canada-Newfoundland and Labrador Offshore Petroleum Board

DNV Det Norske Veritas

DNV- GL Det Norske Veritas GL

EEMUA Engineered Equipment Materials User Association

EI Energy Institute (formerly Institute of Petroleum)

GSO Standardization Organization for the Cooperation Council for the Arab States of the
Gulf

IALA International Association of Marine Aids to Navigation and Lighthouse Authorities

IAPH International Association of Ports and Harbors

IACS International Association of Classification Societies

ICAO International Civil Aviation Organization

IAS Industry Applications Society (under IEEE)

ICS International Chamber of Shipping

IEC International Electrotechnical Commission

IEE Now IET

IEEE Institute of Electrical and Electronics Engineers

IET Institution of Engineering and Technology

IMCA International Maritime Contractors Association

IMO International Maritime Organization

ISO International Organization for Standardization

 Electrotechnical standards relevant for the oil and gas industry / 7

ISGOTT International Safety Guide for Oil Tankers and Terminals

ISPS International Ships and Port Facilities Security Code

LR Lloyds Register

MARPOL International Convention for the Prevention of Pollution From Ships (IMO)

MEPC Marine Environment Protection Committee (in IMO)

NEC National Electrical Code

NEK Norwegian Electrotechnical Committee

NEMA National Electrical Manufacturers Association

NFPA National Fire Protection Association

OCIMF Oil Companies International Marine Forum

IOGP International Association of Oil & Gas Producers

PCIC Petroleum and Chemical Industry Committee (under IEEE IAS)

SCAPC Standards and Conformity Assessment Policy Committee (under NEMA)

SCC Standards Council of Canada

SDO Standards Developing Organization

SOEE Subcommittee on Electrical Equipment

SOLAS International Convention of Safety Of Life At Sea (IMO)

TC Technical Committee

UL Underwriters Laboratories

USCG U.S. Coast Guard

 Electrotechnical standards relevant for the oil and gas industry / 8

IEC standards specific to the oil and gas

industry

IEC 61892-1, Mobile and fixed offshore units Electrical installations Part 1: General
requirements and conditions

IEC 61892-2, Mobile and fixed offshore units Electrical installations Part 2: System design

IEC 61892-3, Mobile and fixed offshore units Electrical installations Part 3: Equipment

IEC 61892-4, Mobile and fixed offshore units Electrical installations Part 4: Cables

IEC 61892-5, Mobile and fixed offshore units Electrical installations Part 5: Mobile units

IEC 61892-6, Mobile and fixed offshore units Electrical installations Part 6: Installation

IEC 61892-7, Mobile and fixed offshore units Electrical installations Part 7: Hazardous areas
 Electrotechnical standards relevant for the oil and gas industry / 9

IEC standards relevant for the oil and gas

industry

IEC 60034, Rotating electrical machines

IEC 60034-1, Rotating electrical machines Part 1: Rating and performance

IEC 60034-11, Rotating electrical machines Part 11: Thermal protection

IEC 60034-12, Rotating electrical machines Part 12: Starting performance of single-speed three
phase cage induction motors

IEC 60034-14, Rotating electrical machines Part 14: Mechanical vibration of certain machines
with shaft heights 56 mm and higher Measurement, evaluation and limits of vibration severity

IEC 60034-15, Rotating electrical machines Part 15: Impulse voltage withstand levels of form-
wound stator coils for rotating a.c. machines

IEC 60034-16, Excitation systems for synchronous machines

IEC 60034-16-1, Rotating electrical machines Part 16: Excitation systems for synchronous
machines - Chapter 1: Definitions

IEC 60034-18, Rotating electrical machines Part 18: Functional evaluation of insulation systems

IEC 60034-18-1, Rotating electrical machines Part 18-1: Functional evaluation of insulation
systems General guidelines

IEC 60034-18-21, Rotating electrical machines Part 18: Functional evaluation of insulation
systems Section 21: Test procedures for wire-wound windings - Thermal evaluation and
classification

IEC 60034-18-22, Rotating electrical machines Part 18-22: Functional evaluation of insulation
systems Test procedures for wire-wound windings - Classification of changes and insulation
component substitutions

IEC 60034-18-31, Rotating electrical machines Part 18-31: Functional evaluation of insulation
systems Test procedures for form-wound windings Thermal evaluation and classification of
insulation systems used in rotating machines

IEC 60034-18-32, Rotating electrical machines Part 18-32: Functional evaluation of insulation
systems Test procedures for form-wound windings - Evaluation by electrical endurance

IEC 60034-18-33, Rotating electrical machines Part 18-33: Functional evaluation of insulation
systems Test procedures for form-wound windings Multifactor evaluation by endurance under
simultaneous thermal and electrical stresses
 Electrotechnical standards relevant for the oil and gas industry / 10

IEC 60034-18-34, Rotating electrical machines Part 18-34: Functional evaluation of insulation
systems Test procedures for form-wound windings Evaluation of thermomechanical endurance
of insulation systems

IEC 60034-18-41, Rotating electrical machines Part 18-41: Qualification and type tests for Type I
electrical insulation systems used in rotating electrical machines fed from voltage converters

IEC 60034-18-42, Rotating electrical machines Part 18-42: Qualification and acceptance tests for
partial discharge resistant electrical insulation systems (Type II) used in rotating electrical
machines fed from voltage converters

IEC 60034-19, Rotating electrical machines Part 19: Specific test methods for d.c. machines on
conventional and rectifier-fed supplies

IEC 60034-2, Rotating electrical machines Part 2-1:Standard methods for determining losses
and efficiency from tests (excluding machines for traction vehicles)

IEC 60034-2-1, Rotating electrical machines Part 2-1: Standard methods for determining losses
and efficiency from tests (excluding machines for traction vehicles).

IEC 60034-22, Rotating electrical machines Part 22: AC generators for reciprocating internal
combustion (RIC) engine driven generating sets

IEC 60034-2-2 , Rotating electrical machines Part 2-2: Specific methods for determining separate
losses of large machines from tests - Supplement to IEC 60034-2-1

IEC 60034-2-3 , Rotating electrical machines Part 2-3: Specific test methods for determining
losses and efficiency of converter-fed AC motors

IEC 60034-25, Rotating electrical machines Part 25: Guidance for the design and performance of
a.c. motors specifically designed for converter supply

IEC 60034-26, Rotating electrical machines Part 26: Effects of unbalanced voltages on the
performance of three-phase cage induction motors

IEC 60034-27, Rotating electrical machines Part 27: Off-line partial discharge measurements on
the stator winding insulation of rotating electrical machines

IEC 60034-28, Rotating electrical machines Part 28: Test methods for determining quantities of
equivalent circuit diagrams for three-phase low-voltage cage induction motors

IEC 60034-29, Rotating electrical machines Part 29: Equivalent loading and superposition
techniques - Indirect testing to determine temperature rise

IEC 60034-2A, Rotating electrical machines Part 2: Methods for determining losses and
efficiency of rotating electrical machinery from tests (excluding machines for traction vehicles)
Measurement of losses by the calorimetric method

IEC 60034-3, Rotating electrical machines Part 3: Specific requirements for synchronous
generators driven by steam turbines or combustion gas turbines
 Electrotechnical standards relevant for the oil and gas industry / 11

IEC 60034-30, Rotating electrical machines Part 30: Efficiency classes of single-speed, three-
phase, cage-induction motors (IE-code)

IEC 60034-31, Rotating electrical machines Part 31: Guide for the selection and application of
energy-efficient motors including variable-speed applications

IEC 60034-4, Rotating electrical machines Part 4: Methods for determining synchronous
machine quantities from tests

IEC 60034-5, Rotating electrical machines Part 5: Degrees of protection provided by the integral
design of rotating electrical machines (IP code) - Classification

IEC 60034-6, Rotating electrical machines Part 6: Methods of cooling (IC Code)

IEC 60034-7, Rotating electrical machines Part 7: Terminal markings and direction of rotation.

IEC 60034-8, Rotating electrical machines Part 8: Terminal markings and direction of rotation

IEC 60034-9, Rotating electrical machines Part 9: Noise limits

IEC 60038, IEC standard voltages

IEC 60044, Instrument transformers

IEC 60044-1, Instrument transformers Part 1: Current transformers

IEC 60044-2, Instrument transformers Part 2 : Inductive voltage transformers

IEC 60044-3, Instrument transformers Part 3: Combined transformers

IEC 60044-5, Instrument transformers Part 5: Capacitor voltage transformers

IEC 60044-6, Instrument transformers Part 6: Requirements for protective current transformers
for transient performance

IEC 60044-7, Instrument transformers Part 7: Electronic voltage transformers

IEC 60044-8, Instrument transformers Part 8: Electronic current transformers

IEC 60050, International Electrotechnical vocabulary

IEC 60050-161, International Electrotechnical Vocabulary Chapter 161: Electromagnetic

compatibility

IEC 60050-191, International Electrotechnical Vocabulary Chapter 191: Dependability and quality
of service

IEC 60050-300, International Electrotechnical Vocabulary Electrical and electronic -

measurements and measuring instruments

IEC 60050-411, International Electrotechnical Vocabulary Part 411: Rotating machinery

 Electrotechnical standards relevant for the oil and gas industry / 12

IEC 60050-426, International Electrotechnical Vocabulary Chapter 426: Equipment for explosive
atmospheres

IEC 60050-441, International Electrotechnical Vocabulary Chapter 441: Switchgear, controlgear

and fuses

IEC 60050-446, International Electrotechnical Vocabulary Chapter 446: Electrical relays

IEC 60050-617, International Electrotechnical Vocabulary Part 617: Organization/Market of

electricity - Edition 1.0

IEC 60050-702, International Electrotechnical Vocabulary Chapter 702: Oscillations, signals and
related devices

IEC 60050-826, International Electrotechnical Vocabulary Part 826: Electrical installations

IEC 60050-845, International Electrotechnical Vocabulary Chapter 845: Lighting

IEC 60051, Direct acting indicating analogue electrical measuring instruments and their
accessories All Parts

IEC 60051-1, Direct acting indicating analogue electrical measuring instruments and their
accessories Part 1: Definitions and general requirements common to all parts

IEC 60051-2, Direct acting indicating analogue electrical measuring instruments and their
accessories Part 2: Special requirements for ammeters and voltmeters

IEC 60051-3, Direct acting indicating analogue electrical measuring instruments and their
accessories Part 3: Special requirements for wattmeters and varmeters

IEC 60051-4, Direct acting indicating analogue electrical measuring instruments and their
accessories Part 4: Special requirements for frequency meters

IEC 60051-5, Direct acting indicating analogue electrical measuring instruments and their
accessories Part 5: Special requirements for phase meters, power factor meters and
synchroscopes

IEC 60051-6, Direct acting indicating analogue electrical measuring instruments and their
accessories Part 6: Special requirements for ohmmeters (impedance meters) and conductance
meters

IEC 60051-7, Direct acting indicating analogue electrical measuring instruments and their
accessories Part 7: Special requirements for multi-function instruments

IEC 60051-8, Direct acting indicating analogue electrical measuring instruments and their
accessories Part 8: Special requirements for accessories

IEC 60051-9, Direct acting indicating analogue electrical measuring instruments and their
accessories Part 9: Recommended test methods

IEC 60059, IEC standard current ratings

 Electrotechnical standards relevant for the oil and gas industry / 13

IEC 60060, High-voltage test techniques.

IEC 60060-1, High-voltage test techniques Part 1: General definitions and test requirements

IEC 60060-2, High voltage test techniques Part 2: Measuring systems

IEC 60060-3, High-voltage test techniques Part 3: Definitions and requirements for on-site
testing

IEC 60061-1, Lamp caps and holders together with gauges for the control of interchangeability and
safety Part 1: Lamp caps

IEC 60064, Tungsten filament lamps for domestic and similar general lighting purposes
Performance requirements

IEC 60068, Environmental testing

IEC 60068-1, Environmental testing Part 1: General and guidance

IEC 60068-2, Environmental testing Part 2-6: Tests Test Fc: Vibration (sinusoidal)

IEC 60068-2-1, Environmental testing Part 2-1: Tests Test A: Cold

IEC 60068-2-14, Environmental testing Part 2-14: Tests Test N: Change of temperature

IEC 60068-2-2 , Environmental testing Part 2-2: Tests Test B: Dry heat

IEC 60068-2-27, Environmental testing Part 2-27: Tests Test Ea and guidance: Shock

IEC 60068-2-30, Environmental testing Part 2-30: Tests Test Db: Damp heat, cyclic (12 h + 12
h cycle)

IEC 60068-2-52, Environmental testing Part 2: Tests, Test Kb: Salt mist, cyclic (sodium chloride
solution)

IEC 60068-2-6, Environmental testing Part 2-6: Tests Test Fc: Vibration (sinusoidal)

IEC 60068-2-75, Environmental testing Part 2: Tests Test Eh: Hammer tests

IEC 60068-2-78, Draft Document - Environmental testing Part 2-78: Tests Test Cab: Damp
heat, steady state

IEC 60071, Insulation co-ordination

IEC 60071-1 Insulation co-ordination Part 1: Definitions, principles and rules

IEC 60071-2 Insulation co-ordination Part 2: Application guide

IEC 60071-4 Insulation co-ordination Part 4: Computational guide to insulation co-ordination

and modelling of electrical networks

IEC 60071-5 Insulation co-ordination Part 5: Procedures for high-voltage direct current (HVDC)
converter stations
 Electrotechnical standards relevant for the oil and gas industry / 14

IEC 60072, Dimensions and output series for rotating electrical machines

IEC 60072-1, Dimensions and output series for rotating electrical machines Part 1: Frame
numbers 56 to 400 and flange numbers 55 to 1080

IEC 60072-2, Dimensions and output series for rotating electrical machines Part 2: Frame
numbers 355 to 1000 and flange numbers 1180 to 2360

IEC 60072-3, Dimensions and output series for rotating electrical machines Part 3: Small built-in
motors - Flange numbers BF10 to BF50

IEC 60073, Basic and safety principles for man-machine interface, marking and identification
Coding principles for indicators and actuators

IEC 60076, Power transformers (all parts)

IEC 60076-1, Power transformers Part 1: General

IEC 60076-10, Power transformers Part 10: Determination of sound levels

IEC 60076-10-1, Power transformers Part 10-1: Determination of sound levels Application
guide

IEC 60076-11, Power transformers Part 11: Dry-type transformers

IEC 60076-12, Power transformers Part 12: Loading guide for dry-type transformers

IEC 60076-13, Power transformers Part 13: Self-protected liquid-filled transformers

IEC 60076-14, Power transformers Part 14: Design and application of liquid-immersed power
transformers using high-temperature insulation materials

IEC 60076-15, Power transformers Part 15: Gas-filled power transformers

IEC 60076-16, Power transformers Part 16: Transformers for wind turbine applications

IEC 60076-17, Power transformers Part 17: Evaluation of electromagnetic fields around power
transformers

IEC 60076-18, Power transformers Part 18: Measurement of frequency response

IEC 60076-2, Power transformers Part 2: Temperature rise for liquid-immersed transformers

IEC 60076-21, Power Transformers Part 21: Standard Requirements, Terminology, and Test
Code for Step-Voltage Regulators

IEC 60076-3 ,Power transformers Part 3: Insulation levels, dielectric tests and external
clearances in air

IEC 60076-3-1, Power Transformers External Clearances In Air

IEC 60076-4, Power transformers Part 4: Guide to the lightning impulse and switching impulse
testing Power transformers and reactors
 Electrotechnical standards relevant for the oil and gas industry / 15

IEC 60076-5, Power transformers Part 5: Ability to withstand short circuit

IEC 60076-6, Power transformers Part 6: Reactors

IEC 60076-7, Power transformers Part 7: Loading guide for oil-immersed power transformers

IEC 60076-8, Power transformers Part 8: Application guide

IEC 60079, Electrical apparatus for explosive gas atmospheres

IEC 60079-0, Explosive atmospheres Part 0: Equipment General requirements

IEC 60079-1, Electrical apparatus for explosive gas atmospheres Flameproof enclosures 'd'

IEC 60079-10, Electrical apparatus for explosive gas atmospheres Part 10: Classification of
hazardous areas

IEC 60079-10-1, Explosive atmospheres Part 10-1: Classification of areas Explosive gas
atmospheres

IEC 60079-10-2, Explosive atmospheres Part 10-2: Classification of areas Combustible dust
atmospheres

IEC 60079-11, Explosive atmospheres Part 11: Equipment protection by intrinsic safety "i"

IEC 60079-13, Electrical apparatus for explosive gas atmosphere Part 13: Construction and use
of rooms or buildings protected by pressurization

IEC 60079-14, Explosive atmospheres Part 14: Electrical installations design, selection and
erection

IEC 60079-15, Explosive atmospheres Part 15: Equipment protection by type of protection "n"

IEC 60079-16, Electrical apparatus for explosive gas atmospheres Part 16: Artificial ventilation
for the protection of analyser(s) houses

IEC 60079-17, Explosive atmospheres Part 17: Electrical installations inspection and
maintenance

IEC 60079-18, Explosive atmospheres Part 18: Equipment protection by encapsulation m

IEC 60079-19, Explosive atmospheres Part 19: Equipment repair, overhaul and reclamation

IEC 60079-2, Explosive atmospheres Part 2: Equipment protection by pressurized enclosure p

IEC 60079-20, Explosive atmospheres Part 20: Material characteristics for gas and vapour
classification

IEC 60079-20-1, Explosive atmospheres Part 20-1: Material characteristics for gas and vapour
classification Test methods and data

IEC 60079-25, Electrical apparatus for explosive gas atmospheres Part 25: Intrinsically safe
systems
 Electrotechnical standards relevant for the oil and gas industry / 16

IEC 60079-26, Explosive atmospheres Part 26: Equipment with equipment protection level (EPL)
Ga

IEC 60079-27, Explosive atmospheres Part 27: Fieldbus intrinsically safe concept (FISCO)

IEC 60079-28, Explosive atmospheres Part 28: Protection of equipment and transmission
systems using optical radiation

IEC 60079-29, Explosive atmospheres Part 29: Gas detectors; Selection, installation, use and
maintenance of detectors for flammable gases and oxygen

IEC 60079-29-1, Explosive atmospheres Part 29-1: Gas detectors Performance requirements
of detectors for flammable gases

IEC 60079-29-2, Explosive atmospheres Part 29-2: Gas detectors Selection, installation, use
and maintenance of detectors for flammable gases and oxygen

IEC 60079-29-3, Explosive atmospheres Part 29-3: Gas detectors- Requirements on the
functional safety of fixed gas detection systems

IEC 60079-29-4, Explosive atmospheres Part 29-4: Gas detectors Performance requirements
of open path detectors for flammable gases

IEC 60079-30-1, Explosive atmospheres Part 30-1: Electrical resistance trace heating General
and testing requirements

IEC 60079-30-2, Explosive atmospheres Part 30-2: Electrical resistance trace heating
Application guide for design, installation and maintenance

IEC 60079-31, Explosive atmospheres Part 31: Equipment dust ignition protection by enclosure
"t"

IEC 60079-33, Explosive atmospheres Part 33: Equipment protection by special protection 's'

IEC 60079-35-1, Caplights for use in mines susceptible to firedamp Part 1: General requirements
Construction and testing in relation to the risk of explosion

IEC 60079-35-2, Caplights for use in mines susceptible to firedamp Part 2: Performance and
other safety-related matters

IEC 60079-5, Explosive atmospheres Part 5: Equipment protection by powder filling q

IEC 60079-6, Explosive atmospheres Part 6: Equipment protection by oil immersion o

IEC 60079-7, Explosive atmospheres Part 7: Equipment protection by increased safety e

IEC 60081, Double-capped fluorescent lamps Performance specifications

IEC 60083, Plugs and socket-outlets for domestic and similar general use standardized in member
countries of IEC

IEC 60085, Electrical insulation Thermal evaluation and designation

 Electrotechnical standards relevant for the oil and gas industry / 17

IEC 60092, Electrical installations in ships

IEC 60092-101, Electrical installations in ships Part 101: Definitions and general requirements

IEC 60092-201, Electrical installation in ships System design General

IEC 60092-302, Electrical installation in ships Low-voltage switchgear and controlgear

assemblies

IEC 60092-350, Electrical installations in ships Part 350: General construction and test methods
of power, control and instrumentation cables for shipboard and offshore applications

IEC 60092-352, Electrical installations in ships Part 352: Choice and installation of electrical
cables

IEC 60092-353, Electrical installations in ships Part 353: Single and multicore non-radial field
power cables with extruded solid insulation for rated voltages 1 kV and 3 kV

IEC 60092-354, Electrical installations in ships Part 354: Single and three-core power cables with
extruded solid insulation for rated voltages 6 kV (Um = 7,2 kV); up to 30 kV (Um = 36 kV)

IEC 60092-360, Electrical installations in ships Part 360: Insulating and sheathing materials for
shipboard and offshore units, power, control, instrumentation and telecommunication cables

IEC 60092-370, Electrical installations in ships Part 370: Guidance on the selection of cables for
telecommunication and data transfer including radio-frequency cables

IEC 60092-376, Electrical installations in ships Part 376: Cables for control and instrumentation
circuits 150/250 V (300 V)

IEC 60092-401, Electrical installations in ships Part 401: Installation and test of completed
installation

IEC 60092-501 , Electrical installations in ships Part 501: Special features Electric propulsion
plant

IEC 60092-502, Electrical installations in ships Part 502: Tankers, Special Features

IEC 60092-504, Electrical installations in ships Part 504: Special features Control and
instrumentation

IEC 60092-509, Electrical installations in ships Part 509: Operation of electrical installations

IEC 60095-1, Lead acid starter batteries Part 1: General requirements and methods of test

IEC 60099, Lightening arresters

IEC 60099-1, Surge arresters Part 1: Non-linear resistor type gapped surge arresters for a.c.
systems

IEC 60099-5, Surge arresters Part 5: Selection and application recommendations

 Electrotechnical standards relevant for the oil and gas industry / 18

IEC 60112, Method for the determination of the proof and the comparative tracking indices of solid
insulating materials

IEC 60120, Dimensions of ball & socket couplings of string insulator units

IEC 60137, Insulated bushings for alternating voltages above 1000 V

IEC 60146, Semiconductor convertors General requirements and line commutated convertors

IEC 60146-1-1, Semiconductor converters General requirements and line commutated

converters Part 1-1: Specification of basic requirements

IEC 60146-1-2, Semiconductor converters - General requirements and line commutated converters
Part 1-2: Application guide

IEC 60146-1-3, Semiconductor converters General requirements and line commutated

converters Part 1-3: Transformers and reactors

IEC 60146-2, Semiconductor converters Part 2: Self-commutated semiconductor converters

including direct d.c. converters

IEC 60152, Identification by hour numbers of the phase conductors of 3-phase electric systems

IEC 60155, Glow-starters for fluorescent lamps

IEC 60156, Insulating liquids Determination of the breakdown voltage at power frequency Test
method

IEC 60169, Radio-frequency connectors

IEC 60183, Guide to the selection of high-voltage cables

IEC 60189-2, Low-frequency cables and wires with PVC insulation and PVC sheath Part 2:
Cables in pairs, triples, quads and quintuples for inside installations

IEC 60191-6, Mechanical standardization of semiconductor devices Part 6: General rules for the
preparation of outline drawings of surface mounted semiconductor device packages

IEC 60196, IEC standard frequencies

IEC 60204-1, Electrical equipment of industrial machines Part 1: General rules

IEC 60214, Tap-changers

IEC 60214-1, Tap-changers Part 1: Performance requirements and test methods

IEC 60214-2, Tap-changers Part 2: Application guide

IEC 60215, Safety requirements for radio transmitting equipment

IEC 60227, Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V (all
parts)
 Electrotechnical standards relevant for the oil and gas industry / 19

IEC 60228, Conductors of insulated cables

IEC 60229, Electric cables Tests on extruded oversheaths with a special protective function

IEC 60243-1, Electric strength of insulating materials Test methods Part 1: Tests at power
frequencies

IEC 60245, Rubber insulated cables Rated voltages up to and including 450/750 V (all parts)

IEC 60247, Insulating liquids Measurement of relative permittivity, dielectric dissipation factor
(tan d) and d.c. resistivity

IEC 60255, Electrical relays

IEC 60255-1, Measuring relays and protection equipment Part 1: Common requirements

IEC 60255-11, Measuring relays and protection equipment Part 11: Voltage dips, short
interruptions, variations and ripple on auxiliary power supply port

IEC 60255-12, Electrical relays Part 12: Directional relays and power relays with two input
energizing quantities

IEC 60255-121, Measuring relays and protection equipment Part 121: Functional requirements
for distance protection

IEC 60255-127, Measuring relays and protection equipment Part 127: Functional requirements
for over/under voltage protection

IEC 60255-13, Electrical relays Part 13: Biased (percentage) differential relays

IEC 60255-151, Measuring relays and protection equipment Part 151: Functional requirements
for over/under current protection

IEC 60255-16, Electrical relays Part 16: Impedance measuring relays

IEC 60255-21-1, Electrical relays Part 21: Vibration, shock, bump and seismic tests on
measuring relays and protection equipment - Section One: Vibration tests (sinusoidal)

IEC 60255-21-2, Electrical relays Part 21: Vibration, shock, bump and seismic tests on
measuring relays and protection equipment Section Two: Shock and bump tests

IEC 60255-21-3, Electrical relays Part 21: Vibration, shock, bump and seismic tests on
measuring relays and protection equipment Section 3: Seismic tests

IEC 60255-22-1, Measuring relays and protection equipment Part 22-1: Electrical disturbance
tests 1 MHz burst immunity tests

IEC 60255-22-2, Measuring relays and protection equipment Part 22-2: Electrical disturbance
tests Electrostatic discharge tests

IEC 60255-22-3, Measuring relays and protection equipment Part 22-3: Electrical disturbance
tests Radiated electromagnetic field immunity
 Electrotechnical standards relevant for the oil and gas industry / 20

IEC 60255-22-4, Measuring relays and protection equipment Part 22-4: Electrical disturbance
tests - Electrical fast transient/burst immunity test

IEC 60255-22-5, Measuring relays and protection equipment Part 22-5: Electrical disturbance
tests - Surge immunity test

IEC 60255-22-6, Electrical relays Part 22-6: Electrical disturbance tests for measuring relays and
protection equipment Immunity to conducted disturbances induced by radio frequency fields

IEC 60255-22-7, Electrical relays Part 22-7: Electrical disturbance tests for measuring relays and
protection equipment Power frequency immunity tests

IEC 60255-24, Electrical relays Part 24: Common format for transient data exchange
(COMTRADE) for power systems

IEC 60255-25, Electrical relays Part 25: Electromagnetic emission tests for measuring relays and
protection equipment

IEC 60255-26, Measuring relays and protection equipment Part 26: Electromagnetic compatibility
requirements

IEC 60255-27, Measuring relays and protection equipment Part 27: Product safety requirements

IEC 60255-5, Electrical Relays Part 5: Insulation coordination for measuring relays and
protection equipment Requirements and tests

IEC 60255-6, Electrical relays Part 6: Measuring relays and protection equipment

IEC 60255-8, Electrical relays Part 8: Thermal electrical relays

IEC 60265-1, High-voltage switches Part 1: Switches for rated voltages above 1 kV and less than
52 kV

IEC 60268, Sound system equipment

IEC 60268-16, Sound system equipment Part 16: Objective rating of speech intelligibility by
speech transmission index

IEC 60268-3, Sound System Equipment Part 3: Amplifiers

IEC 60269, Low-voltage fuses

IEC 60269-1, Low-voltage fuses Part 1: General requirements

IEC 60269-2, Low voltage fuses Part 2: Supplementary requirements for fuses for use by
authorized persons (fuses mainly for industrial application)

IEC 60269-2-1, Low-voltage fuses Part 2-1: Supplementary requirements for fuses for use by
authorized persons (fuses mainly for industrial application) - Sections I to VI: Examples of types of
standardized fuses
 Electrotechnical standards relevant for the oil and gas industry / 21

IEC 60269-3, Low-voltage fuses Part 3: Supplementary requirements for fuses for use by
unskilled persons (fuses mainly for household or similar applications) - Examples of standardized
systems of fuses A to F

IEC 60270, High-voltage test techniques Partial discharge measurements

IEC 60282-1, High-voltage fuses Part 1: Current-limiting fuses

IEC 60282-2, High-voltage fuses Part 2: Expulsion fuses

IEC 60287, Electric cables Calculation of the current rating (all parts)

IEC 60287-1-1, Electric cables Calculation of the current rating Part 1-1: Current rating
equations (100 % load factor) and calculation of losses - General

IEC 60287-1-2 , Electric cables Calculation of the current rating Part 1: Current rating equations
(100 % load factor) and calculations of losses - Section 2: Sheath eddy current loss factors for two
circuits in flat formation

IEC 60287-1-3, Electric cables - Calculation of the current rating Part 1-3: Current rating
equations (100 % load factor) and calculation of losses - Current sharing between parallel single-
core cables and calculation of circulating current losses

IEC 60287-2-1 , Electric cables - Calculation of the current rating Part 2-1: Thermal resistance -
Calculation of thermal resistance

IEC 60287-2-2 , Electric cables - Calculation of the current rating Part 2: Thermal resistance -
Section 2: A method for calculating reduction factors for groups of cables in free air, protected from
solar radiation

IEC 60287-3-1 , Electric cables - Calculation of the current rating Part 3-1: Sections on operating
conditions - Reference operating conditions and selection of cable type

IEC 60287-3-2 , Electric cables - Calculation of the current rating Part 3: Sections on operating
conditions - Section 2: Economic optimization of power cable size

IEC 60287-3-3 , Electric cables - Calculation of the current rating Part 3-3: Sections on operating
conditions - Cables crossing external heat sources

IEC 60296, Fluids for electrotechnical applications Unused mineral insulating oils for
transformers and switchgear

IEC 60298, AC Metal Enclosed Switchgear & Control gear for rated voltages above 1kV and up to
and including 52kV

IEC 60300, Dependability management

IEC 60300-1, Dependability management Part 1: Dependability management systems

IEC 60300-2, Dependability management Part 2: Guidelines for dependability management

 Electrotechnical standards relevant for the oil and gas industry / 22

IEC 60300-3-1 , Dependability management Part 3-1: Application guide Analysis techniques for
dependability Guide on methodology

IEC 60300-3-10, Dependability management Part 3-10: Application guide Maintainability

IEC 60300-3-11, Dependability management Part 3-11: Application guide Reliability centred
maintenance

IEC 60300-3-12, Dependability management Part 3-12: Application guide Integrated logistic
support

IEC 60300-3-14, Dependability management Application guide Maintenance and maintenance

support

IEC 60300-3-15, Dependability management Application guide Engineering of system

dependability

IEC 60300-3-16, Dependability management Part 3-16: Application guide Guidelines for the
specification of maintenance support services

IEC 60300-3-2 , Dependability management Part 3-2: Application guide Collection of

dependability data from the field

IEC 60300-3-3 , Dependability management Application guide Life cycle costing

IEC 60300-3-4 , Draft Document Dependability Management Part 3: Application Guide

Section 4: Guide to the Specification of Dependability Requirements

IEC 60300-3-5 , Dependability management Part 3-5: Application guide Reliability test
conditions and statistical test principles

IEC 60304, Standard colours for insulation for low-frequency cables and wires

IEC 60309, Plugs, socket-outlets and couplers for industrial proposes

IEC 60309-1, Plugs, socket-outlets and couplers for industrial purposes Part 1: General
requirements

IEC 60309-2, Plugs, socket-outlets and couplers for industrial purposes Part 2: Dimensional
interchangeability requirements for pin and contact-tube accessories

IEC 60309-4, Plugs, socket-outlets and couplers for industrial purposes Part 4: Switched socket-
outlets and connectors with or without interlock

IEC 60317, Specifications for particular types of winding wires

IEC 60331, Tests for electric cables under fire conditions Circuit integrity

IEC 60331-1, Tests for electric cables under fire conditions Circuit integrity Part 1: Test method
for fire with shock at a temperature of at least 830 C for cables of rated voltage up to and
including 0,6/1,0 kV and with an overall diameter exceeding 20 mm
 Electrotechnical standards relevant for the oil and gas industry / 23

IEC 60331-11, Tests for electric cables under fire conditions Circuit integrity Part 11: Apparatus
- Fire alone at a flame temperature of at least 750 C

IEC 60331-2, Tests for electric cables under fire conditions Circuit integrity Part 2: Test method
for fire with shock at a temperature of at least 830 C for cables of rated voltage up to and
including 0,6/1,0 kV and with an overall diameter not exceeding 20 mm

IEC 60331-21, Tests for electric cables under fire conditions Circuit integrity Part 21:
Procedures and requirements Cables of rated voltage up to and including 0,6/1,0 kV

IEC 60331-23, Tests for electric cables under fire conditions Circuit integrity Part 23:
Procedures and requirements - Electric data cables

IEC 60331-25, Tests for electric cables under fire conditions Circuit integrity Part 25:
Procedures and requirements Optical fibre cables

IEC 60331-3, Tests for electric cables under fire conditions Circuit integrity Part 3: Test method
for fire with shock at a temperature of at least 830 C for cables of rated voltage up to and
including 0,6/1,0 kV tested in a metal enclosure

IEC 60332, Tests on electric and optical fibre cables under fire conditions

IEC 60332-1, Tests on electric and optical fibre cables under fire conditions Part 1: Test for
vertical flame propagation for a single insulated wire or cable

IEC 60332-1-1, Tests on electric and optical fibre cables under fire conditions Part 1-1: Test for
vertical flame propagation for a single insulated wire or cable Apparatus

IEC 60332-1-2, Tests on electric and optical fibre cables under fire conditions Part 1-2: Test for
vertical flame propagation for a single insulated wire or cable Procedure for 1 kW pre-mixed
flame

IEC 60332-1-3 , Tests on electric and optical fibre cables under fire conditions Part 1-3: Test for
vertical flame propagation for a single insulated wire or cable Procedure for determination of
flaming droplets/particles

IEC 60332-2-1 , Tests on electric and optical fibre cables under fire conditions Part 2-1: Test for
vertical flame propagation for a single small insulated wire or cable Apparatus

IEC 60332-2-2 , Tests on electric and optical fibre cables under fire conditions Part 2-2: Test for
vertical flame propagation for a single small insulated wire or cable Procedure for diffusion flame

IEC 60332-3, Tests on electric cables under fire conditions (various Parts) - Test for vertical flame
spread of vertically mounted bunched wires or cables

IEC 60332-3-10, Tests on electric and optical fibre cables under fire conditions Part 3-10: Test
for vertical flame spread of vertically-mounted bunched wires or cables Apparatus

IEC 60332-3-21, Tests on electric cables under fire conditions Part 3-21: Test for vertical flame
spread of vertically-mounted bunched wires or cables Category A F/R
 Electrotechnical standards relevant for the oil and gas industry / 24

IEC 60332-3-22, Tests on electric cables under fire conditions Part 3-22: Test for vertical flame
spread of vertically-mounted bunched wires or cables Category A

IEC 60332-3-23, Tests on electric and optical fibre cables under fire conditions Part 3-23: Test
for vertical flame spread of vertically-mounted bunched wires or cables Category B

IEC 60332-3-24, Tests on electric and optical fibre cables under fire conditions Part 3-24: Test
for vertical flame spread of vertically-mounted bunched wires or cables Category C

IEC 60332-3-25, Tests on electric and optical fibre cables under fire conditions Part 3-25: Test
for vertical flame spread of vertically-mounted bunched wires or cables Category D

IEC 60335, Household and similar electrical appliances (relevant parts)

IEC 60335-1, Household and similar electrical appliances Safety Part 1: General requirements

IEC 60335-2-29, Household and similar electrical appliances Safety Part 2-29: Particular
requirements for battery chargers

IEC 60354, Loading Guide For Oil-Immersed Transformers

IEC 60364, Low-voltage electrical installations

IEC 60364-1, Low-voltage electrical installations Part 1: Fundamental principles, assessment of

general characteristics, definitions

IEC 60364-4-41, Low-voltage electrical installations Part 4-41: Protection for safety Protection
against electric shock

IEC 60364-4-43, Low-voltage electrical installations Part 4-43: Protection for safety Protection
against overcurrent

IEC 60364-4-44, Low-voltage electrical installations Part 4-44: Protection for safety Protection
against voltage disturbances and electromagnetic disturbances.

IEC 60364-5-52, Low-voltage electrical installations Part 5-52: Selection and erection of electrical
equipment Wiring systems

IEC 60364-5-53, Electrical installations of buildings Part 5-53: Selection and erection of electrical
equipment Isolation, switching and control

IEC 60364-5-54, Low-voltage electrical installations Part 5-54: Selection and erection of electrical
equipment Earthing arrangement and protective conductors

IEC 60364-5-548, Electrical installations of buildings Part 5: Selection and erection of electrical
equipment Section 548: Earthing arrangements and Equipotential Bonding for information
technology installations

IEC 60364-5-55, Electrical installations of buildings Part 5-55: Selection and erection of electrical
equipment Other equipment

IEC 60364-6, Low voltage electrical installations Part 6: Verification

 Electrotechnical standards relevant for the oil and gas industry / 25

IEC 60364-7-710, Electrical installations of buildings Part 7-710: Requirements for special
installations or locations Medical locations

IEC 60364-7-712, Electrical installations of buildings Part 7-712: Requirements for special
installations or locations Solar photovoltaic (PV) power supply systems

IEC 60376, Specification of technical grade sulfur hexafluoride (SF6) for use in electrical equipment

IEC 60383, Plugs and socket-outlets for domestic and similar general use standardized in member
countries of IEC

IEC 60398, Industrial electroheating installations General test methods

IEC 60400, Lampholders for tubular fluorescent lamps and starterholders

IEC 60417, Graphical symbols for use on equipment

IEC 60417-1, Graphical symbols for use on equipment Part 1: Overview and application

IEC 60422, Mineral insulating oils in electrical equipment Supervision and maintenance guidance

IEC 60432, Incandescent lamps Safety specifications

IEC 60432-1, Incandescent lamps Safety specifications Part 1: Tungsten filament lamps for
domestic and similar general lighting purposes

IEC 60433, Insulators for overhead lines with a nominal voltage above 1 000 V Ceramic
insulators for a.c. systems Characteristics of insulator units of the long rod type

IEC 60439, Low-voltage switchgear and control gear assemblies.

IEC 60439-1, Low-voltage switchgear and control gear assemblies Part 1: Type-tested and
partially type-tested assemblies

IEC 60439-2, Low-voltage switchgear and controlgear assemblies Part 2: Particular

requirements for busbar trunking systems (busways)

IEC 60439-4, Low-voltage switchgear and controlgear assemblies Part 4: Particular

requirements for assemblies for construction sites (ACS)

IEC 60446, Basic and safety principles for man-machine interface, marking and identification
Identification of conductors by colours

IEC 60447, Basic and safety principles for man-machine interface, marking and identification
Actuating principles

IEC 60449, Voltage bands for electrical installations of buildings

IEC 60450, Measurement of the average viscometric degree of polymerization of new and aged
cellulosic electrically insulating materials

IEC 60454-2, Specifications for pressure-sensitive adhesive tapes For electrical purposes Part 2:
Methods of test
 Electrotechnical standards relevant for the oil and gas industry / 26

IEC 60470, High-voltage alternating current contactors

IEC 60473, Dimensions for panel-mounted indicating and recording electrical measuring
instruments

IEC 60478, Stabilized power supplies, DC output

IEC 60479, Guide to effects of current on human beings and livestock (Parts 1-4)

IEC 60480, Guidelines for the checking and treatment of sulphur hexafluoride (SF6) taken from
electrical equipment and specification for its re-use

IEC 60487, Methods of measurement for equipment used in terrestrial radio-relay systems.

IEC 60502, Power cables with extruded insulation and their accessories for rated voltages from 1
kV (Um = 1,2 kV) up to 30 kV (Um = 36 kV)

IEC 60502-1, Power cables with extruded insulation and their accessories for rated voltages from 1
kV (Um = 1,2 kV) up to 30 kV (Um = 36 kV) Part 1: Cables for rated voltages of 1 kV (Um = 1,2
kV) and 3 kV (Um = 3,6 kV)

IEC 60502-2, Power cables with extruded insulation and their accessories for rated voltages from 1
kV (Um = 1,2 kV) up to 30 kV (Um = 36 kV) Part 2: Cables for rated voltages from 6 kV (Um =
7,2 kV) up to 30 kV (Um = 36 kV)

IEC 60502-4, Power cables with extruded insulation and their accessories for rated voltages from 1
kV (Um = 1,2 kV) up to 30 kV (Um = 36 kV) Part 4: Test requirements on accessories for cables
with rated voltages from 6 kV (Um = 7,2 kV) up to 30 kV (Um = 36 kV)

IEC 60519-10, Safety in electroheat installations Part 10: Particular requirements for electrical
resistance trace heating systems for industrial and commercial applications

IEC 60529, Degrees of protection provided by enclosures (IP Code)

IEC 60533, Electrical and electronic installations in ships Electromagnetic compatibility

IEC 60534, Industrial-process control valves

IEC 60534-1, Industrial-process control valves Part 1: Control valve terminology and general
considerations

IEC 60534-2, Industrial-process control valves Part 2: Flow capacity

IEC 60534-2-1, Industrial-process control valves Part 2-1: Flow capacity Sizing equations for
fluid flow under installed conditions

IEC 60534-2-3 , Industrial-process control valves Part 2-3: Flow capacity Test procedures

IEC 60534-2-4 , Industrial-process control valves Part 2-4: Flow capacity Inherent flow
characteristics and rangeability

IEC 60534-2-5 , Industrial-process control valves Part 2-5: Flow capacity Sizing equations for
fluid flow through multistage control valves with interstage recovery
 Electrotechnical standards relevant for the oil and gas industry / 27

IEC 60534-3-1 , Industrial-process control valves Part 3-1: Dimensions Face-to-face

dimensions for flanged, two-way, globe-type, straight pattern and centre-to-face dimensions for
flanged, two-way, globe-type, angle pattern control valves

IEC 60534-3-2, Industrial-process control valves Part 3-2: Dimensions Face-to-face

dimensions for rotary control valves except butterfly valves

IEC 60534-3-3 , Industrial-process control valves Part 3-3: Dimensions End-to-end dimensions
for buttweld, two-way, globe-type, straight pattern control valves

IEC 60534-4, Industrial-process control valves Part 4: Inspection and routine testing

IEC 60534-5, Industrial-process control valves Part 5: Marking

IEC 60534-6-1, Industrial-process control valves Part 6: Mounting details for attachment of
positioners to control valves Section 1: Positioner mounting on linear actuators

IEC 60534-6-2 , Industrial-process control valves Part 6-2: Mounting details for attachment of
positioners to control valves Positioner mounting on rotary actuators

IEC 60534-7, Industrial process control valves Part 7: Control valve data sheet

IEC 60534-8-3, Industrial-process control valves Part 8-3: Noise considerations Control valve
aerodynamic noise prediction method

IEC 60534-8-4 , Industrial-process control valves Part 8-4: Noise considerations Prediction of
noise generated by hydrodynamic flow

IEC 60536, Classification of electrical and electronic equipment with regard to protection against
electric shock.

IEC 60549, High-voltage fuses for the external protection of shunt power capacitors

IEC 60567, Oil-filled electrical equipment - Sampling of gases and analysis of free and dissolved
gases Guidance

IEC 60584-1, Thermocouples Part 1: Reference tables

IEC 60584-2, Thermocouples Part 2: Tolerances

IEC 60584-3, Thermocouples Part 3: Extension and compensating cables - Tolerances and
identification system

IEC 60598, Luminaires

IEC 60598-1, Luminaires Part 1: General requirements and tests

IEC 60598-2-1, Luminaires Part 2: Particular requirements Section 1: Fixed general purpose
luminaires

IEC 60598-2-2, Luminaires Part 2: Particular requirements Section 2: Recessed luminaires

 Electrotechnical standards relevant for the oil and gas industry / 28

IEC 60598-2-22, Luminaires Part 2-22: Particular requirements Luminaires for emergency
lighting

IEC 60598-2-5, Luminaires Part 2-5: Particular requirements Floodlights

IEC 60598-2-6, Luminaires Part 2: Particular requirements Section 6: Luminaires with built-in
transformers for filament lamps

IEC 60599, Mineral oil-impregnated electrical equipment in service Guide to the interpretation of
dissolved and free gases analysis

IEC 60616, Terminal and tapping markings for power transformers

IEC 60617, Graphical symbols for diagrams DATABASE

IEC 60622, Secondary cells and batteries containing alkaline or other non-acid electrolytes
Sealed nickel-cadmium prismatic rechargeable single cells

IEC 60623, Secondary cells and batteries containing alkaline or other non-acid electrolytes
Vented nickel-cadmium prismatic rechargeable single cells

IEC 60644, Specification for high-voltage fuse-links for motor circuit applications

IEC 60654, Industrial-process measurement and control equipment Operating conditions

IEC 60654-1, Industrial-process measurement and control equipment Operating conditions

Part 1: Climatic conditions

IEC 60654-2, Operating conditions for industrial-process measurement and control equipment.
Part 2: Power

IEC 60654-3, Operating conditions for industrial-process measurement and control equipment
Part 3: Mechanical influences

IEC 60654-4, Operating conditions for industrial-process measurement and control equipment.
Part 4: Corrosive and erosive influences

IEC 60662, High-pressure sodium vapour lamps

IEC 60664, Insulation coordination for equipment within low-voltage systems

IEC 60664-1, Insulation coordination for equipment within low-voltage systems Part 1: Principles,
requirements and tests

IEC 60664-3, Insulation coordination for equipment within low-voltage systems Part 3: Use of
coating, potting or moulding for protection against pollution

IEC 60669, Switches for household and similar fixed-electrical installations (all parts)

IEC 60684-1, Flexible Insulating sleeving Part 1: Definitions and general requirements

IEC 60688, Electrical measuring transducers for converting a.c. electrical quantities to analogue or
digital signals
 Electrotechnical standards relevant for the oil and gas industry / 29

IEC 60694, Common specifications for high-voltage switchgear and controlgear standards

IEC 60695, Fire hazard testing

IEC 60695-2-10, Fire Hazard testing Part 2-10: Glowing/hot-wire based test methods Glow-
wire apparatus and common test procedure

IEC 60695-2-11, Fire hazard testing Part 2-11: Glowing/hot-wire based test methods Glow-wire
flammability test method for end-products

IEC 60706, Maintainability of equipment

IEC 60706-2, Maintainability of equipment Part 2: Maintainability requirements and studies

during the design and development phase

IEC 60706-3, Maintainability of equipment Part 3: Verification and collection, analysis and
presentation of data

IEC 60721, Classification of environmental conditions

IEC 60721-2-1, Classification of environmental conditions Part 2-1: Environmental conditions

appearing in nature Temperature and humidity

IEC 60721-2-2 , Environmental conditions appearing in nature Precipitation and wind

IEC 60721-3-2 , Guidance for the correlation and transformation of environmental condition classes
of IEC 60721-3 to the environmental tests of IEC 60068 Transportation

IEC 60721-3-3 , Classification of environmental conditions Part 3-3: Classification of groups of

environmental parameters and their severities Stationary use at weatherprotected locations

IEC 60721-3-4, Classification of environmental conditions Part 3: Classification of groups of

environmental parameters and their severities Section 4: Stationary use at non-weatherprotected
locations

IEC 60721-3-6, Classification of environmental conditions Part 3: Classification of groups of

environmental parameters and their severities Ship environment

IEC 60724, Short-circuit temperature limits of electric cables with rated voltages of 1 kV (Um = 1,2
kV) and 3 kV (Um = 3,6 kV)

IEC 60724, Guide to the short-circuit temperature limits of electric cables

IEC 60726, Loading guide for dry-type power transformers

IEC 60745, Hand-held motor-operated electric tools Safety

IEC 60751, Industrial platinum resistance thermometers and platinum temperature sensors

IEC 60754, Test on gases evolved during combustion of materials from cables

IEC 60754-1, Test on gases evolved during combustion of materials from cables Part 1:
Determination of the amount of halogen acid gas
 Electrotechnical standards relevant for the oil and gas industry / 30

IEC 60754-2, Test on gases evolved during combustion of materials from cables Part 2:
Determination of acidity (by pH measurement) and conductivity

IEC 60770-1, Transmitters for use in industrial-process control systems Part 1: Methods for
performance evaluation

IEC 60793-1, Optical fibres Part 1: Measurement methods and test procedures

IEC 60793-1-1, Optical fibres Part 1-1: Measurement methods and test procedures General
and guidance

IEC 60793-2, Optical fibres Part 2: Product specifications General

IEC 60793-2-10, Optical fibres Part 2-10: Product specifications Sectional specification for
category A1 multimode fibres

IEC 60793-2-20, Optical fibres Part 2-20: Product specifications Sectional specification for
category A2 multimode fibres

IEC 60793-2-30, Optical fibres Part 2-30: Product specifications Sectional specification for
category A3 multimode fibres

IEC 60793-2-40, Optical fibres Part 2-40: Product specifications Sectional specification for
category A4 multimode fibres

IEC 60793-2-50, Optical fibres Part 2-50: Product specifications Sectional specification for
class B single-mode fibres

IEC 60793-2-60, Optical fibres Part 2-60: Product specifications Sectional specification for
category C single-mode intraconnection fibres

IEC 60794, Optical fibre cables

IEC 60794-1, Optical fibre cables Part 1: Generic specification

IEC 60794-1-1, Optical fibre cables Part 1-1: Generic specification General

IEC 60794-1-2 , Optical fibre cables Part 1-2: Generic specification Basic optical cable test
procedures

IEC 60794-2, Optical fibre cables Part 2: Indoor cables Sectional specification

IEC 60794-2-10, Optical fibre cables Part 2-10: Indoor cables Family specification for simplex
and duplex cables

IEC 60794-2-11, Optical fibre cables Part 2-11: Indoor cables Detailed specification for simplex
and duplex cables for use in premises cabling

IEC 60794-2-20, Optical fibre cables Part 2-20: Indoor cables Family specification for multi-
fibre optical distribution cables

IEC 60794-2-21, Optical fibre cables Part 2-21: Indoor cables Detailed specification for multi-
fibre optical distribution cables for use in premises cabling
 Electrotechnical standards relevant for the oil and gas industry / 31

IEC 60794-2-30, Optical fibre cables Part 2-30: Indoor cables Family specification for ribbon
cables

IEC 60794-2-31, Optical fibre cables Part 2-31: Indoor cables Detailed specification for optical
fibre ribbon cables for use in premises cabling

IEC 60794-2-40, Optical fibre cables Part 2-40: Indoor optical fibre cables Family specification
for A4 fibre cables

IEC 60794-2-41, Optical fibre cables Part 2-41: Indoor cables Product specification for simplex
and duplex buffered A4 fibres

IEC 60794-2-42, Optical fibre cables Part 2-42: Indoor optical fibre cables Product specification
for simplex and duplex cables with A4 fibres

IEC 60794-2-50, Optical fibre cables Part 2-50: Indoor cables Family specification for simplex
and duplex cables for use in terminated cable assemblies

IEC 60794-2-51, Optical fibre cables Part 2-51: Indoor optical fibre cables Product specification
for simplex and duplex cables for use in patchcords for controlled environment

IEC 60794-3, Optical fibre cables Part 3: Sectional specification Outdoor cables

IEC 60794-3-10, Optical fibre cables Part 3-10: Outdoor cables Family specification for duct,
directly buried and lashed aerial optical telecommunication cables

IEC 60794-3-11, Optical fibre cables Part 3-11: Outdoor cables Product specification for duct,
directly buried, and lashed aerial single-mode optical fibre telecommunication cables

IEC 60794-3-12, Optical fibre cables Part 3-12: Outdoor cables Detailed specification for duct
and directly buried optical telecommunication cables for use in premises cabling

IEC 60794-3-20, Optical fibre cables Part 3-20: Outdoor cables Family specification for self-
supporting aerial telecommunication cables

IEC 60794-3-21, Optical fibre cables Part 3-21: Outdoor cables Detailed specification for

IEC 60794-3-30, Optical fibre cables Part 3-30: Outdoor cables Family specification for optical
telecommunication cables for lakes, river crossings and coastal application

IEC 60794-3-40, Optical fibre cables Part 3-40: Outdoor cables Family specification for sewer
cables and conduits for installation by blowing and/or pulling in non-man accessible storm and
sanitary sewers

IEC 60794-3-50, Optical fibre cables Part 3-50: Outdoor cables Family specification for gas
pipe cables and subducts for installation by blowing and/or pulling/dragging in gas pipes

IEC 60794-3-60, Optical fibre cables Part 3-60: Outdoor cables Family specification for drinking
water pipe cables and subducts for installation by blowing and/or pulling/dragging/floating in
drinking water pipes
 Electrotechnical standards relevant for the oil and gas industry / 32

IEC 60794-4, Optical fibre cables Part 4: Sectional specification - Aerial optical cables along
electrical power lines

IEC 60794-4-10, Optical fibre cables Part 4-10: Aerial optical cables along electrical power lines
Family specification for OPGW (Optical Ground Wires)

IEC 60794-4-20, Optical fibre cables Part 4-20: Aerial optical cables along electrical power lines
Family specification for ADSS (All Dielectric Self Supported) Optical cables

IEC 60794-5, Optical fibre cables Part 5: Sectional specification Microduct cabling for
installation by blowing

IEC 60794-5-10, Optical fibre cables: Part 5-10 Family specification for outdoor microduct optical
fibre cables, microducts and protected microducts for installation by blowing

IEC 60794-5-20, Optical fibre cables Part 5-20: Family specification for outdoor microduct fibre
units, microducts and protected microducts for installation by blowing

IEC 60801, Electromagnetic compatibility for industrial-process measurement and control

equipment.

IEC 60811, Common test methods for insulating and sheathing materials of electric cables

IEC 60811-2-1, Common test methods for insulating and sheathing materials of electric and optical
cables Part 2-1: Methods specific to elastomeric compounds - Ozone resistance, hot set and
mineral oil immersion tests

IEC 60812, Analysis techniques for system reliability Procedure for failure mode and effects
analysis (FMEA)

IEC 60814, Insulating liquids Oil-impregnated paper and pressboard Determination of water by
automatic coulometric Karl Fischer titration

IEC 60815, Guide for the selection of insulators in respect of polluted conditions

IEC 60825, Safety of laser products (all parts)

IEC 60831, Shunt power capacitors of the self-heating type for a.c. systems having a rated voltage
up to and including 1kV

IEC 60835-3-5, Methods of measurement for equipment used in digital microwave radio
transmission systems Part 3: Measurement on satellite earth stations Section 5: Up- and down-
converters

IEC 60840, Power cables with extruded insulation and their accessories for rated voltages above
30 kV (Um=36 kV) up to 150 kV (Um =170 kV) Test methods and requirements.

IEC 60851, Stationary lead-acid batteries

IEC 60865, Short-circuit currents Calculation of effects

 Electrotechnical standards relevant for the oil and gas industry / 33

IEC 60870-1-2, Telecontrol equipment and systems Part 1: General considerations Section 2:
Guide for specifications

IEC 60870-5-103, Telecontrol equipment and systems Part 5-103: Transmission protocols
Companion Standard for the informative interface of protection equipment

IEC 60871, Shunt capacitors for a.c. power systems having a rated voltage above 1 000 V

IEC 60871-1, Shunt capacitors for a.c. power systems having a rated voltage above 1 000 V Part
1: General

IEC 60871-4, Shunt capacitors for AC power systems having a rated voltage above 1 000V Part
4: Internal fuses

IEC 60877, Procedures for ensuring the cleanliness of industrial-process measurement and control
equipment in oxygen service

IEC 60884, Plugs and socket-outlets for household and similar purposes (all parts)

IEC 60885, Electrical test methods for electric cables Part 2: Partial discharge tests

IEC 60885-2, Electrical test methods for electric cables Part 2: Partial discharge tests

IEC 60888, Zinc-coated steel wires for stranded conductors

IEC 60894, Guide for test procedure for the measurement of loss tangent of coils and bars for
machine windings

IEC 60896, Stationary lead-acid batteries General requirements and methods of testing.

IEC 60896-11, Stationary lead-acid batteries Part 11: Vented types General requirements and
methods of test

IEC 60896-21, Stationary lead-acid batteries Part 21: Valve regulated types Methods of test

IEC 60896-22, Stationary lead-acid batteries Part 22: Valve regulated types Requirements

IEC 60898, Electrical accessories Circuit-breakers for overcurrent protection for household and
similar installations

IEC 60898-1, Electrical accessories Circuit-breakers for overcurrent protection for household and
similar installations Part 1: Circuit-breakers for a.c. operation

IEC 60900, Live working Hand tools for use up to 1 000 V a.c. and 1 500 V d.c

IEC 60904, Photovoltaic devices

IEC 60905, Loading Guide For Dry-Type Power Transformers

IEC 60906, IEC system of plugs and socket-outlets for household and similar purposes (all parts)

IEC 60909, Short-circuit currents in three-phase a.c. systems

 Electrotechnical standards relevant for the oil and gas industry / 34

IEC 60909-0, Short-circuit currents in three-phase a.c. systems Part 0: Calculation of currents

IEC 60909-1, Short-circuit currents in three-phase a.c. systems Part 1: Factors for the calculation
of short-circuit currents according to IEC 60909-0

IEC 60909-2, Short-circuit currents in three-phase a.c. systems Part 2: Data of electrical
equipment for short-circuit current calculations

IEC 60909-3, Short-circuit currents in three-phase a.c. systems Part 3: Currents during two
separate simultaneous line-to-earth short circuits and partial short-circuit currents flowing through
earth

IEC 60909-4, Short-circuit currents in three-phase a.c. systems Part 4: Examples for the
calculation of short-circuit currents

IEC 60921, Ballasts for tubular fluorescent lamps Performance requirements

IEC 60923, Auxiliaries for lamps Ballasts for discharge lamps (excluding tubular fluorescent
lamps) Performance requirements

IEC 60927, Auxiliaries for lamps Starting devices (other than glow starters) Performance
requirements

IEC 60929, AC-supplied electronic ballasts for tubular fluorescent lamps Performance
requirements

IEC 60931-3, Shunt power capacitors of the non-self-healing type for a.c. systems having a rated
voltage up to and including 1 000V Part 3: Internal fuses

IEC 60945, Maritime navigation and radiocommunication equipment and systems General
requirements Methods of testing and required test results

IEC 60947, Low-voltage switchgear and controlgear

IEC 60947-1, Low-voltage switchgear and control gear Part 1: General rules

IEC 60947-2, Low-voltage switchgear and controlgear Part 2: Circuit-breakers

IEC 60947-3, Low-voltage switchgear and controlgear Part 3: Switches, disconnectors, switch-
disconnectors and fuse-combination units

IEC 60947-4-1, Low-voltage switchgear and controlgear Part 4-1: Contactors and motor-starters
Electromechanical contactors and motor-starters

IEC 60947-4-2 , Low-voltage switchgear and controlgear Part 4-2: Contactors and motor-starters
AC semiconductor motor controllers and starters

IEC 60947-5-1 , Low-voltage switchgear and controlgear Part 5-1: Control circuit devices and
switching elements Electromechanical control circuit devices

IEC 60947-5-2 , Low-voltage switchgear and controlgear Part 5-2: Control circuit devices and
switching elements Proximity switches
 Electrotechnical standards relevant for the oil and gas industry / 35

IEC 60947-5-6, Low-voltage switchgear and control gear

IEC 60947-6-1 , Low-voltage switchgear and controlgear Part 6-1: Multiple function equipment
Transfer switching equipment

IEC 60947-6-2, Low-voltage switchgear and controlgear Part 6-2: Multiple function equipment
Control and protective switching devices (or equipment) (CPS)

IEC 60949, Calculation of thermally permissible short-circuit currents, taking into account non-
adiabatic heating effects

IEC 60950-1, Information technology equipment Safety Part 1: General requirements

IEC 60968, Self-ballasted lamps for general lighting services Safety requirements

IEC 60969, Self-ballasted lamps for general lighting services Performance requirements

IEC 60974, Arc welding equipment

IEC 60974-1, Arc welding equipment Welding power sources

IEC 60986, Short-circuit temperature limits of electric cables with rated voltages from 6 kV (Um =
7,2 kV) up to 30 kV (Um = 36 kV)

IEC 60993, Electrolyte for vented nickel-cadmium cells

IEC 61000, Electromagnetic compatibility

IEC 61000-1-1, Electromagnetic compatibility (EMC) Part 1: General Section 1: Application and
interpretation of fundamental definitions and terms

IEC 61000-2, Electromagnetic compatibility (EMC) Part 2: Environment

IEC 61000-2-1, Electromagnetic compatibility (EMC) Part 2: Environment Section 1:

Description of the environment Electromagnetic environment for low-frequency conducted
disturbances and signalling in public power supply systems

IEC 61000-2-2, Electromagnetic compatibility (EMC) Part 2-2: Environment Compatibility levels
for low-frequency conducted disturbances and signalling in public low-voltage power supply
systems

IEC 61000-2-4 , Electromagnetic compatibility (EMC) Part 2-4: Environment Compatibility levels
in industrial plants for low-frequency conducted disturbance.

IEC 61000-2-5, Electromagnetic compatibility (EMC) Part 2-5: Environment Description and
classification of electromagnetic environments

IEC 61000-3, Electromagnetic compatibility (EMC) Part 3: Limits

IEC 61000-3-12, Electromagnetic compatibility (EMC) Part 3-12: Limits Limits for harmonic
currents produced by equipment connected to public low-voltage systems with input current >16 A
and 75 A per phase
 Electrotechnical standards relevant for the oil and gas industry / 36

IEC 61000-3-2 , Electromagnetic compatibility (EMC) Part 3-2: Limits Limits for harmonic
current emissions (equipment input current 16 A per phase)

IEC 61000-3-4 , Electromagnetic compatibility (EMC) Part 3-4: Limits Limitation of emission of
harmonic currents in low-voltage power supply systems for equipment with rated current greater
than 16 A

IEC 61000-3-6, Electromagnetic compatibility (EMC) Part 3-6: Limits Assessment of emission
limits for the connection of distorting installations to MV, HV and EHV power systems

IEC 61000-4, Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques

IEC 61000-4-1 , Electromagnetic compatibility (EMC) Part 4-1: Testing and measurement
techniques Overview of IEC 61000-4 series

IEC 61000-4-11, Electromagnetic compatibility (EMC) Part 4-11: Testing and measurement
techniques Voltage dips, short interruptions and voltage variations immunity tests

IEC 61000-4-12, Electromagnetic compatibility (EMC) Part 4-12: Testing and measurement
techniques Ring wave immunity test

IEC 61000-4-2 , Electromagnetic compatibility (EMC) Part 4-2: Testing and measurement
techniques Electrostatic discharge immunity test

IEC 61000-4-3 , Electromagnetic compatibility (EMC) Part 4-3 : Testing and measurement
techniques Radiated, radio-frequency, electromagnetic field immunity test

IEC 61000-4-4 , Electromagnetic compatibility (EMC) Part 4-4: Testing and measurement
techniques Electrical fast transient/burst immunity test

IEC 61000-4-5, Electromagnetic compatibility (EMC) Part 4-5: Testing and measurement
techniques Surge immunity test

IEC 61000-4-6 , Electromagnetic compatibility (EMC) Part 4-6: Testing and measurement
techniques Immunity to conducted disturbances, induced by radio-frequency fields

IEC 61000-4-7 , Electromagnetic compatibility (EMC) Part 4-7: Testing and measurement
techniques General guide on harmonics and interharmonics measurements and instrumentation,
for power supply systems and equipment connected thereto

IEC 61000-4-8, Electromagnetic compatibility (EMC) Part 4-8: Testing and measurement
techniques Power frequency magnetic field immunity test

IEC 61000-5, Electromagnetic compatibility (EMC) Part 5: Installation and mitigation guidelines

IEC 61000-5-1 , Electromagnetic compatibility (EMC) Part 5: Installation and mitigation guidelines
Section 1: General considerations Basic EMC publication

IEC 61000-5-2 , Electromagnetic compatibility (EMC) Part 5: Installation and mitigation guidelines
Section 2: Earthing and cabling
 Electrotechnical standards relevant for the oil and gas industry / 37

IEC 61000-6, Electromagnetic compatibility (EMC) Generic standards Immunity for residential,
commercial and light-industrial environments

IEC 61000-6-1 , Electromagnetic compatibility (EMC) Part 6-1: Generic standards Immunity for
residential, commercial and light-industrial environments

IEC 61000-6-2, Electromagnetic compatibility (EMC) Part 6-2: Generic standards Immunity for
industrial environments

IEC 61000-6-3 , Electromagnetic compatibility (EMC) Part 6-3: Generic standards Emission
standard for residential, commercial and light-industrial environments

IEC 61000-6-4, Electromagnetic compatibility (EMC) Part 6-4: Generic standards Emission
standard for industrial environments

IEC 61000-6-5, Electromagnetic compatibility (EMC) Part 6-5: Generic standards Immunity for
power station and substation environments

IEC 61010, Safety requirements for electrical equipment for measurement, control, and laboratory
use

IEC 61010-1, Safety requirements for electrical equipment for measurement, control, and
laboratory use Part 1: General requirements

IEC 61024, Protection of structures against lighting

IEC 61025, Fault tree analysis (FTA)

IEC 61034, Measurement of smoke density of cables burning under defined conditions

IEC 61034-1, Measurement of smoke density of cables burning under defined conditions Part 1:
Test apparatus

IEC 61034-2, Measurement of smoke density of cables burning under defined conditions Part 2:
Test procedure and requirements

IEC 61057, Aerial devices with insulating boom used for live working

IEC 61058, Switches for appliances

IEC 61071, Capacitors for power electronics

IEC 61078, Analysis techniques for dependability Reliability block diagram and boolean methods

IEC 61082-1, Preparation of documents used in electrotechnology Part 1: Rules

IEC 61086-1, Coatings for loaded printed wire boards (conformal coatings) Part 1: Definitions,
classification and general requirements

IEC 61086-2, Coatings for loaded printed wire boards (conformal coatings) Part 2: Methods of
test

IEC 61089, Round wire concentric lay overhead electrical stranded conductors Equipment
 Electrotechnical standards relevant for the oil and gas industry / 38

IEC 61097, Global maritime distress and safety system (GMDSS) (all parts)

IEC 61099, Specifications for unused synthetic organic esters for electrical purposes

IEC 61109, Composite insulators for a.c overhead lines with a nominal voltage greater than 1 000
V. Definitions, test methods and acceptance criteria

IEC 61111, Live working Electrical insulating matting

IEC 61131, Programmable controllers

IEC 61131-1, Programmable controllers Part 1: General information

IEC 61131-2, Programmable controllers Part 2: Equipment requirements and tests

IEC 61131-3, Programmable controllers Part 3: Programming languages

IEC 61131-4 , Programmable controllers Part 4: User guidelines

IEC 61131-5, Programmable controllers Part 5: Communications

IEC 61140, Protection against electric shock Common aspects for installation and equipment

IEC 61146, Methods of measurement for video cameras (PAL/SECAM/NTSC)

IEC 61158, Digital data communications for measurement and control Fieldbus for use in
industrial control systems

IEC 61158-2, Industrial communication networks Fieldbus specifications Part 2: Physical layer
specification and service definition

IEC 61165, Application of Markov techniques

IEC 61167, Metal halide lamps

IEC 61181, Mineral oil-filled electrical equipment Application of dissolved gas analysis (DGA) to
factory tests on electrical equipment

IEC 61195, Double-capped fluorescent lamps Safety specifications

IEC 61200-704, Electrical installation guide Part 704: Construction and demolition site
installations

IEC 61204, Low-voltage power supply devices, d.c. output Performance characteristics

IEC 61215, Crystalline silicon terrestrial photovoltaic (PV) modules - Design qualification and type
approval

IEC 61230, Live working Portable equipment for earthing or earthing and short-circuiting

IEC 61231, International lamp coding system (ILCOS)

IEC 61238-1, Compression and mechanical connectors for power cables

 Electrotechnical standards relevant for the oil and gas industry / 39

IEC 61241, Electrical apparatus for use in the presence of combustible dusts

IEC 61241-10, Electrical apparatus for use in the presence of combustible dust Part 10:
Classification of areas where combustible dusts are or may be present

IEC 61241-4, Electrical apparatus for use in the presence of combustible dust Part 4: Type of
protection "pD"

IEC 61285, Industrial process control Safety of analyzer houses

IEC 61293, Marking of electrical equipment with ratings related to electrical supply Safety
requirements

IEC 61310-1, Safety of machinery Indication, marking and actuation Part 1: Requirements for
visual, acoustic and tactile signals

IEC 61312, Protection against lightning electromagnetic impulse

IEC 61326, Electrical equipment for measurement, control and laboratory use EMC requirements
General requirements

IEC 61340-4-1, Electrostatics Part 4-1: Standard test methods for specific applications
Electrical resistance of floor coverings and installed floors

IEC 61347, Lamp controlgear

IEC 61363-1, Electrical installations of ships and mobile and fixed offshore units Part 1:
Procedures for calculating short circuit currents in three phase a.c.

IEC 61378, Convertor transformers

IEC 61378-1, Convertor transformers Part 1: Transformers for industrial applications

IEC 61378-3, Converter transformers Part 3: Application guide

IEC 61400-24, Wind turbines Part 24: Lightning protection

IEC 61427, Secondary cells and batteries for photovoltaic energy systems (PVES) General
requirements and methods of test

IEC 61427-1, Secondary cells and batteries for renewable energy storage - General requirements
and methods of test Part 1: Photovoltaic off-grid application

IEC 61434, Secondary cells and batteries containing alkaline or other non-acid electrolytes
Guide to designation of current in alkaline secondary cell and battery standards

IEC 61439, Low-voltage switchgear and control gear assemblies

IEC 61439-0, Low-voltage switchgear and controlgear assemblies Part 0: Guide to specifying
assemblies

IEC 61439-1, Low-voltage switchgear and controlgear assemblies Part 1: General rules
 Electrotechnical standards relevant for the oil and gas industry / 40

IEC 61439-2, Low-voltage switchgear and controlgear assemblies Part 2: Power switchgear and
controlgear assemblies

IEC 61439-3, Low-voltage switchgear and controlgear assemblies Part 3: Distribution boards

IEC 61439-4, Low-voltage switchgear and controlgear assemblies Part 4: Assemblies for
construction sites (ACS)

IEC 61439-5, Low-voltage switchgear and controlgear assemblies Part 5: Assemblies for power
distribution in public networks

IEC 61439-6, Low-voltage switchgear and controlgear assemblies Part 6: Busbar trunking
systems (busways)

IEC 61442, Test methods for accessories for power cables

IEC 61443, Short-circuit temperature limits of electric cables with rated voltages above 30 kV (Um
= 36 kV)

IEC 61466, Composite string insulator units for overhead lines with a nominal voltage greater than
1 000 V

IEC 61478, Live working Ladders of insulating material

IEC 61508, Functional safety of electrical/electronic/programmable electronic safety-related

systems all parts

IEC 61508-1, Functional safety of electrical/electronic/programmable electronic safety-related

systems Part 1: General requirements

IEC 61508-2, Functional safety of electrical/electronic/programmable electronic safety-related

systems Part 2: Requirements for electrical/electronic/programmable electronic safety-related
systems (see Functional Safety and IEC 61508)

IEC 61508-3, Functional safety of electrical/electronic/programmable electronic safety-related

systems Part 3: Software requirements (see Functional Safety and IEC 61508)

IEC 61508-4, Functional safety of electrical/electronic/programmable electronic safety-related

systems Part 4: Definitions and abbreviations

IEC 61508-5, Functional safety of electrical/electronic/programmable electronic safety related

systems Part 5: Examples of methods for the determination of safety integrity levels

IEC 61508-6, Functional safety of electrical/electronic/programmable electronic safety-related

systems Part 6: Guidelines on the application of IEC 61508-2 and IEC 61508-3

IEC 61508-7, Functional safety of electrical/electronic/programmable electronic safety-related

systems Part 7: Overview of techniques and measures

IEC 61511, Functional safety Safety instrumented systems for the process industry sector
 Electrotechnical standards relevant for the oil and gas industry / 41

IEC 61511-1, Functional safety Safety instrumented systems for the process industry sector
Part 1: Framework, definitions, system, hardware and software requirements

IEC 61511-2, Functional safety Safety instrumented systems for the process industry sector
Part 2: Guidelines for the application of IEC 61511-1

IEC 61511-3, Functional safety Safety instrumented systems for the process industry sector
Part 3: Guidance for the determination of the required safety integrity levels

IEC 61518, Mating dimensions between differential pressure (type) measuring instruments and
flanged-on shut-off devices up to 413 BAR (41,3 MPa)

IEC 61537, Cable management Cable tray systems and cable ladder systems

IEC 61554, Panel mounted equipment Electrical measuring instruments Dimensions for panel
mounting

IEC 61557, Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c.

IEC 61557-8, Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V
d.c. Equipment for testing, measuring or monitoring of protective measurers Part 8: Insulation
monitoring devices for IT systems

IEC 61557-9, Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V
d.c. - Equipment for testing, measuring or monitoring of protective measures Part 9: Equipment
for insulation fault location in IT systems

IEC 61558, Safety of power transformers, power supplies, reactors and similar products

IEC 61558-2-4 , Safety of transformers, reactors, power supply units and similar products for
supply voltages up to 1 100 V Part 2-4: Particular requirements and tests for isolating
transformers and power supply units incorporating isolating transformers

IEC 61558-2-6 , Safety of transformers, reactors, power supply units and similar products for
supply voltages up to 1 100 V Part 2-6: Particular requirements and tests for safety isolating
transformers and power supply units incorporating safety isolating transformers

IEC 61634, High-voltage switchgear and controlgear Use and handling of sulphur hexafluoride
(SF6) in high-voltage switchgear and controlgear

IEC 61639, Direct connection between power transformers and gas-insulated metal-enclosed
switchgear for rated voltages of 72,5 kV and above

IEC 61641, Enclosed low-voltage switchgear and controlgear assemblies Guide for testing under
conditions of arcing due to internal fault

IEC 61660-1, Short-circuit currents in d.c. auxiliary installations in power plants and substations
Part 1: Calculation of short-circuit currents

IEC 61672, Electroacoustics Sound level meters

IEC 61701, Salt mist corrosion testing of photovoltaic (PV) modules

 Electrotechnical standards relevant for the oil and gas industry / 42

IEC 61772, Nuclear power plants Control rooms Application of visual display units (VDUs)

IEC 61779-1, IECEx Test Report for IEC 61779-1 (1998) ed 1.0 Electrical apparatus for the
detection and measurement of flammable gases Part 1: General requirements and test methods

IEC 61779-4, IECEx Test Report for IEC 61779-4 (1998) ed 1.0 Electrical apparatus for the
detection and measurement of flammable gases Part 4: Performance requirements for group II
apparatus indicating a volume fraction up to 100% lower explosive limit

IEC 61779-5, IECEx Test Report for IEC 61779-5 (1998) ed 1.0 - Electrical apparatus for the
detection and measurement of flammable gases Part 5: Performance requirements for group II
apparatus indicating a volume fraction up to 100% gas

IEC 61779-6, Electrical apparatus for the detection and measurement of flammable gases Part 6:
Guide for the selection, installation, use and maintenance of apparatus for the detection and
measurement of flammable gases

IEC 61784, Industrial communication networks Profiles

IEC 61800, Adjustable speed electrical power drive systems (all parts)

IEC 61800-1, Adjustable speed electrical power drive systems Part 1: General requirements -
Rating specifications for low voltage adjustable speed d.c. power drive systems

IEC 61800-2, Adjustable speed electrical power drive systems Part 2: General requirements -
Rating specifications for low voltage adjustable frequency a.c. power drive systems

IEC 61800-3, Adjustable speed electrical power drive systems Part 3: EMC requirements and
specific test methods

IEC 61800-4, Adjustable speed electrical power drive systems Part 4: General requirements -
Rating specifications for a.c. power drive systems above 1000 V a.c. and not exceeding 35 kV

IEC 61800-5-1, Adjustable speed electrical power drive systems Part 5-1: Safety requirements -
Electrical, thermal and energy

IEC 61804, Function Blocks (FB) for process control

IEC 61812-1, Time relays for industrial and residential use Part 1: Requirements and tests

IEC 61850, Communication networks and systems for power utility automation

IEC 61850-10, Communication networks and systems in substations Part 10: Conformance
testing

IEC 61850-3, Communication networks and systems in substations Part 3: General requirements

IEC 61850-4, Communication networks and systems in substations Part 4: System and project
management

IEC 61850-5, Communication networks and systems in substations Part 5: Communication

requirements for functions and device models
 Electrotechnical standards relevant for the oil and gas industry / 43

IEC 61850-6, Communication networks and systems for power utility automation Part 6:
Configuration description language for communication in electrical substations related to IEDs

IEC 61850-7-1 , Communication networks and systems for power utility automation Part 7-1:
Basic communication structure Principles and models

IEC 61850-7-2 , Communication networks and systems for power utility automation Part 7-2:
Basic information and communication structure - Abstract communication service interface (ACSI)

IEC 61850-7-3 , Communication networks and systems for power utility automation Part 7-3:
Basic communication structure - Common data classes

IEC 61850-7-4 , Communication networks and systems for power utility automation Part 7-4:
Basic communication structure - Compatible logical node classes and data object classes

IEC 61850-8-1 , Communication networks and systems for power utility automation Part 8-1:
Specific communication service mapping (SCSM) Mappings to MMS (ISO 9506-1 and ISO 9506-
2) and to ISO/IEC 8802-3

IEC 61850-9-1 , Communication networks and systems in substations Part 9-1: Specific
communication service mapping (SCSM) Sampled values over serial unidirectional multidrop
point to point link

IEC 61850-9-2, Communication networks and systems for power utility automation Part 9-2:
Specific communication service mapping (SCSM) Sampled values over ISO/IEC 8802-3

IEC 61869, Instrument transformers

IEC 61869-1, Instrument transformers Part 1: General requirements

IEC 61869-2, Instrument transformers Part 2: Additional requirements for current transformers

IEC 61869-3, Instrument transformers Part 3: Additional requirements for inductive voltage
transformers

IEC 61869-5, Instrument transformers Part 5: Additional requirements for capacitor voltage
transformers Edition 1.0

IEC 61882, Hazard and operability studies (HAZOP studies) - Application guide

IEC 61892-1, Mobile and fixed offshore units - Electrical installations Part 1: General
requirements and conditions

IEC 61892-2, Mobile and fixed offshore units - Electrical installations Part 2: System design

IEC 61892-3, Mobile and fixed offshore units - Electrical installations Part 3: Equipment

IEC 61892-4, Mobile and fixed offshore units - Electrical installations Part 4: Cables

IEC 61892-5, Mobile and fixed offshore units - Electrical installations Part 5: Mobile units

IEC 61892-6, Mobile and fixed offshore units - Electrical installations Part 6: Installation
 Electrotechnical standards relevant for the oil and gas industry / 44

IEC 61892-7, Mobile and fixed offshore units - Electrical installations Part 7: Hazardous areas

IEC 61914, Cable cleats for electrical installations

IEC 61936, Power installations exceeding 1 kV a.c.

IEC 61936-1, Power installation exceeding 1 kV AC Part 1: Common rules

IEC 61993-2, Maritime navigation and radiocommunication equipment and systems Automatic
Identification Systems (AIS) Part 2: Class A shipborne equipment of the automatic identification
system (AIS) - Operational and performance requirements, methods of test and required test
results

IEC 62035, Discharge lamps (excluding fluorescent lamps) Safety specifications

IEC 62040, Uninterruptible Power Systems (UPS)

IEC 62040-1, Uninterruptible power systems (UPS) Part 1: General and safety requirements for
UPS

IEC 62040-1-1 , Uninterruptible Power Systems (UPS) Part 1-2: General and safety requirements
for UPS used in operator access areas

IEC 62040-1-2, Uninterruptible Power Systems (UPS) Part 1-1: General and safety requirements
for UPS used in restricted access locations

IEC 62040-2, Uninterruptible power systems (UPS) Part 2: Electromagnetic compatibility (EMC)
requirements

IEC 62040-3, Uninterruptible Power Systems (UPS) Part 3: Method of Specifying the
Performance and Test Requirements

IEC 62052-11, Electricity metering equipment (AC) General requirements, tests and test
conditions Part 11: Metering equipment

IEC 62061, Safety of machinery - Functional safety of safety-related electrical, electronic and
programmable electronic control systems

IEC 62086-1, Electrical apparatus for explosive gas atmospheres Electrical resistance trace
heating Part 1: General and Testing requirements

IEC 62086-2, Electrical apparatus for explosive gas atmospheres Electrical resistance trace
heating Part 2: Application Guide for design, installation and maintenance

IEC 62155, Hollow pressurized and unpressurized ceramic and glass insulators for use in electrical
equipment with rated voltages greater than 1000 V

IEC 62198, Project risk management Application guidelines

IEC 62246, Reed switches

IEC 62246-1-1, Reed switches Part 1-1: Generic specification Quality assessment
 Electrotechnical standards relevant for the oil and gas industry / 45

IEC 62259, Secondary cells and batteries containing alkaline or other non-acid electrolytes
Nickel-cadmium prismatic secondary single cells with partial gas recombination

IEC 62262, Degree of protection provided by enclosures for electrical equipment against external
mechanical impacts (IK code)

IEC 62271, High-voltage switchgear and controlgear

IEC 62271-1, High-voltage switchgear and controlgear Part 1: Common specifications

IEC 62271-100, High-voltage switchgear and controlgear Part 100: Alternating-current circuit-
breakers

IEC 62271-102, High-voltage switchgear and controlgear Part 102: Alternating current
disconnectors and earthing switches

IEC 62271-103, High-voltage switchgear and controlgear Part 103: Switches for rated voltages
above 1 kV up to and including 52 kV

IEC 62271-105, High-voltage switchgear and control gear Pt 105: High-voltage alternating
current switch-fuse combinations

IEC 62271-106, High-voltage switchgear and controlgear Part 106: Alternating current
contactors, contactor-based controllers and motor-starters

IEC 62271-200, High-voltage switchgear and controlgear Part 200: AC metal-enclosed

switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV

IEC 62271-201, High-voltage switchgear and controlgear Part 201: AC solid insulation-enclosed
switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV

IEC 62271-203, High-voltage switchgear and controlgear Part 203: Gas-insulated metal-
enclosed switchgear for rated voltages above 52 kV

IEC 62305, Protection against lightning (all parts)

IEC 62305-1, Protection against lightning Part 1: General principles

IEC 62305-2, Protection against lightning Part 2: Risk management

IEC 62305-3, Protection against lightning Part 3: Physical damage to structures and life hazard

IEC 62305-4, Protection against lightning Part 4: Electrical and electronic systems within
structures

IEC 62309, Dependability of products containing reused parts Requirements for functionality and
tests

IEC 62337, Commissioning of electrical, instrumentation and control systems in the process
industry Specific phases and milestones

IEC 62381, Automation systems in the process industry Factory acceptance test (FAT), site
acceptance test (SAT) and site integration test (SIT)
 Electrotechnical standards relevant for the oil and gas industry / 46

IEC 62382, Automation systems in the process industry Electrical and instrumentation loop
check

IEC 62388, Maritime navigation and radiocommunication equipment and systems Shipborne
radar Performance requirements, methods of testing and required test results

IEC 62395, Electrical resistance trace heating systems for industrial and commercial applications

IEC 62395-1, Electrical resistance trace heating systems for industrial and commercial applications
Part 1: General and testing requirements

IEC/TS 62395-2, Electrical resistance trace heating systems for industrial and commercial
applications Part 2: Application guide for system design, installation and maintenance

IEC 62402, Obsolescence Management Application guide

IEC 62439, High availability automation networks

IEC 62443, Industrial communication networks Network and system security

IEC 62443-3, Security for industrial process measurement and control Network and system
security

IEC 62535, Insulating liquids Test method for detection of potentially corrosive sulphur in used
and unused insulating oil

IEC 62591, Industrial communication networks Wireless communication network and

communication profiles WirelessHART TM

IEC 62642-1, Alarm systems - Intrusion and hold-up systems Part 1: System requirements

IEC 80000-13, Quantities and units Part 13: Information science and technology

IEC 80000-14, Quantities and units Part 14: Telebiometrics related to human physiology

IEC 80000-6, Quantities and units Part 6: Electromagnetism

IEC 81346-1, Industrial systems, installations and equipment and industrial products. Structuring
principles and reference designations Part 1: Basic rules

IEC CISPR 11, Industrial, scientific and medical equipment Radio-frequency disturbance
characteristics Limits and methods of measurement

IEC CISPR 14 , Electromagnetic compatibility Requirements for household appliances, electric

tools and similar apparatus

IEC CISPR 16-1-1, Specification for radio disturbance and immunity measuring apparatus and
methods Part 1-1: Radio disturbance and immunity measuring apparatus Measuring apparatus

IEC CISPR 16-1-2, Specification for radio disturbance and immunity measuring apparatus and
methods Part 1-2: Radio disturbance and immunity measuring apparatus - Ancillary equipment
Conducted disturbances
 Electrotechnical standards relevant for the oil and gas industry / 47

IEC CISPR 16-1-3, Specification for radio disturbance and immunity measuring apparatus and
methods Part 1-3: Radio disturbance and immunity measuring apparatus Ancillary equipment
Disturbance power

IEC CISPR 16-1-4, Specification for radio disturbance and immunity measuring apparatus and
methods Part 1-4: Radio disturbance and immunity measuring apparatus Antennas and test
sites for radiated disturbance measurements

IEC CISPR 16-1-5, Specification for radio disturbance and immunity measuring apparatus and
methods Part 1-5: Radio disturbance and immunity measuring apparatus Antenna calibration
test sites for 30 MHz to 1 000 MHz

IEC CISPR 22, Information technology equipment Radio disturbance characteristics Limits and
methods of measurement

IEC TR 60034-16-2, Rotating electrical machines Part 16: Excitation systems for synchronous
machines - Chapter 2: Models for power system studies

IEC TR 60079-13, Atmosferas explosivas Parte 13: Proteo de equipamentos por ambiente
pressurizado p

IEC TR 60079-16, Electrical apparatus for explosive gas atmospheres Part 16: Artificial
ventilation for the protection of analyser(s) houses

IEC TR 60079-20, Explosive atmospheres Part 20: Material characteristics for gas and vapour
classification

IEC TR 60092-370, Electrical installations in ships Part 370: Guidance on the selection of cables
for telecommunication and data transfer including radio-frequency cables

IEC TR 60146-1-2, Semiconductor converters General requirements and line commutated

converters Part 1-2: Application guide

IEC TR 60269-5, Low-voltage fuses Part 5: Guidance for the application of low-voltage fuses

IEC TR 60616, Terminal and tapping marking for power transformers

IEC TR 60815, Guide for the Selection of Insulators in Respect of Polluted Conditions

IEC TR 60890, A method of temperature-rise assessment by extrapolation for partially type-tested

assemblies (PTTA) of low-voltage switchgear and controlgear

IEC TR 60894, Guide for test procedure for the measurement of loss tangent of coils and bars for
machine windings

IEC TR 61000-1, Electromagnetic compatibility (EMC) Part 1: General

IEC TR 61000-2-5, Electromagnetic compatibility (EMC) Part 2-5: Environment - Description and
classification of electromagnetic environments

IEC TR 61000-3-6, Electromagnetic compatibility (EMC) Part 3-6: Limits - Assessment of

emission limits for the connection of distorting installations to MV, HV and EHV power systems
 Electrotechnical standards relevant for the oil and gas industry / 48

IEC TR 61000-5-1, Electromagnetic compatibility (EMC) Part 5: Installation and mitigation

guidelines - Section 1: General considerations - Basic EMC publication

IEC TR 61000-5-2, Electromagnetic compatibility (EMC) Part 5: Installation and mitigation

guidelines - Section 2: Earthing and cabling

IEC TR 61508-0, Functional safety of electrical/electronic/programmable electronic safety-related

systems. Functional safety and IEC 61508

IEC TR 61641, Enclosed low-voltage switchgear and controlgear assemblies Guide for testing
under conditions of arcing due to internal fault

IEC TR 61800-6, Adjustable speed electrical power drive systems Part 6: Guide for
determination of types of load duty and corresponding current ratings

IEC TR 61850-1, Communication networks and systems for power utility automation Part 1:
Introduction and overview

IEC TR 62063 High-voltage switchgear and controlgear The use of electronic and associated
technologies in auxiliary equipment of switchgear and controlgear

IEC TR 62482, Electrical installations in ships - Electromagnetic compatibility - Optimising of cable

installations on ships - Testing method of routing distance

IEC TS 60034 -17, Rotating electrical machines Part 17: Cage induction motors when fed from
converters Application guide.

IEC TS 60034 -25, Rotating electrical machines Part 25: Guidance for the design and
performance of a.c. motors specially

IEC TS 60034-16-3, Rotating electrical machines Part 16: Excitation systems for synchronous
machines Section 3: Dynamic performance

IEC TS 60034-17, Rotating electrical machines Part 17: Cage induction motors when fed from
converters Application guide

IEC TS 60034-18-41, Rotating electrical machines Part 18-41: Qualification and type tests for
Type I electrical insulation systems used in rotating electrical machines fed from voltage converters

IEC TS 60034-18-42, Rotating electrical machines Part 18-42: Qualification and acceptance
tests for partial discharge resistant electrical insulation systems (Type II) used in rotating electrical
machines fed from voltage converters

IEC TS 60034-20-1, Rotating electrical machines Part 20-1: Control motors - Stepping motors

IEC TS 60034-23, Rotating electrical machines Part 23: Specification for the refurbishing of
rotating electrical machines

IEC TS 60034-24, Rotating electrical machines Part 24: Online detection and diagnosis of
potential failures at the active parts of rotating electrical machines and of bearing currents
Application guide
 Electrotechnical standards relevant for the oil and gas industry / 49

IEC TS 60034-25, Rotating electrical machines Part 25: AC electrical machines used in power
drive systems Application guide

IEC TS 60034-27-2, Rotating electrical machines Part 27-2: On-line partial discharge
measurements on the stator winding insulation of rotating electrical machines

IEC TS 60034-31, Rotating electrical machines Part 31: Selection of energy-efficient motors
including variable speed applications - Application guide

IEC TS 60076-14, Power transformers Part 14: Liquid-immersed power transformers using high-
temperature insulation materials

IEC TS 60079-32-1, Explosive atmospheres Electrostatic hazards, guidance

IEC TS 60479-1, Effects of current on human beings and livestock Part 1: General aspects

IEC TS 60815, Guide for the selection of insulators in respect of polluted conditions

IEC TS 61000-3-4, Electromagnetic Compatibility (EMC) Part 3-4: Limits Limitation of Emission
of Harmonic Currents in Low-voltage Power Supply Systems for Equipment with Rated Current
Greater than 16 A

IEC TS 61000-6-5, Electromagnetic compatibility (EMC) Part 6-5: Generic standards Immunity
for power station and substation environments

IEC TS 61201, Use of conventional touch voltage limits Application guide Use of conventional
touch voltage limits Application guide

IEC TS 61639, Direct connection between power transformers and gas-insulated metal-enclosed
switchgear for rated voltages of 72,5 kV and above

IEC TS 61850-2, Communication networks and systems in substations Part 2: Glossary

IECEx 01, IEC System for Certification to Standards relating to Equipment for use in Explosive
Atmospheres (IECEx System) - Basic Rules

IECEx 02, IEC System for Certification to Standards relating to Equipment for use in Explosive
Atmospheres (IECEx System) IECEx Certified Equipment Scheme covering equipment for use in
explosive atmospheres Rules of Procedure

IECEx 03, IECEx Certified Service Facilities Scheme Part 3: Ex installation and initial inspection

IECEx 04, IEC Scheme for Certification to Standards relating to Equipment for use in Explosive
Atmospheres (IECEx Scheme) IECEx Conformity Mark Licensing System Regulations

IECEx 05, IEC System for Certification to Standards relating to Equipment for use in Explosive
Atmospheres (IECEx System) IECEx Scheme for Certification of Personnel Competence for
Explosive Atmospheres Rules of Procedure
 Electrotechnical standards relevant for the oil and gas industry / 50

API Standards
API RP 2FPS, RP Planning Design Construction of Floating Production System

API RP 11S3, Electric Submersible Pump Installations

API RP 11S4, RP for Sizing and Selection of Electric Submersible Pump Installations

API RP 14F, Design and Installation of Electrical Systems for Fixed and Floating Offshore
Petroleum Facilities for Unclassified and Class I, Division 1, and Division 2 Locations

API RP 14FZ, Design and Installation of Electrical Systems for Fixed and Floating Offshore
Petroleum Facilities for Unclassified and Class I, Zone 0, Zone 1, and Zone 2 Locations

API RP 500, RP for Classification of Locations for Electrical Installations at Petroleum Facilities
Classified as Class I, Division 1 and Division 2 (ANSI/API RP 500-1998)

API RP 505, RP for Classification of Locations for Electrical Installations at Petroleum Facilities
Classified as Class I, Zone 0, Zone 1 and Zone 2 (ANSI/API RP 505-1998)

API RP 540, Electrical installation in petroleum processing plant

API RP 545, RP for Lightning Protection of Aboveground Storage Tanks for Flammable or
Combustible Liquids

API RP 2003, Protection Against Ignitions Arising out of Static, Lightning and Stray Currents

API STD 541, Form-Wound Squirrel-Cage Induction Motors 500 Horsepower and Larger

API STD 547, General-purpose Form-wound Squirrel Cage Induction Motors-250 Horsepower and
Larger
 Electrotechnical standards relevant for the oil and gas industry / 51

IEEE (PCIC) Standards

IEEE 100, The Authoritative Dictionary of IEEE Standards Terms

IEEE 1017, RP for Field Testing Electric Submersible Pump Cable

IEEE 1018, RP for Specifying Electric Submersible Pump Cable Ethylene-Propylene Rubber
Insulation

IEEE 1019, RP for Specifying Electric Submersible Pump Cable Polypropylene Insulation

IEEE 1068, Standard for the Repair & Rewinding of AC Electric Motors in the Petroleum,
Chemical, and Process Industries

IEEE 1068, Standard for the Repair & Rewinding of AC Electric Motors in the Petroleum,
Chemical, and Process Industries

IEEE 1100, RP for powering and grounding sensitive electronic equipment (Emerald Book)

IEEE 1115, IEEE RP for Sizing Nickel-Cadmium Batteries for Stationary Applications

IEEE 112, IEEE Standard Test Procedure for Polyphase Induction Motors and Generators

IEEE 115, IEEE Guide: Test Procedures for Synchronous Machines Part I - Acceptance and
Performance Testing Part II - Test Procedures and Parameter Determination for Dynamic Analysis

IEEE 1159, RP for Monitoring Electric Power Quality

IEEE 1184, Guide for selection and sizing of batteries for uninterruptible power supplies

IEEE 1188, IEEE RP for Maintenance, Testing, and Replacement of Valve-Regulated Lead-Acid
(VRLA) Batteries for Stationary Applications

IEEE 1202, Standard for Flame Testing of Cables for Use in Cable Tray in Industrial and
Commercial Occupancies

IEEE 1242, Guide for Specifying & Selecting Power, Control, and Special-Purpose Cable for
Petrochemical Plants

IEEE 1276 , Guide for the application of High-Temperature Insulation Materials in Liquid-Immersed
Power Transformers

IEEE 1313.1, Standard for Insulation Coordination Definitions practices and Rules

IEEE 1313.2, Guide for the Application of Insulation Coordination

IEEE 1349, Guide for Application of Electric Motors in Class I Division 2, & Class I Zone 2
Hazardous Locations

IEEE 141, RP for Electric Power Distribution for Industrial Plants (IEEE Red Book)
 Electrotechnical standards relevant for the oil and gas industry / 52

IEEE 142, RP for Grounding of Industrial and Commercial Power Systems

IEEE 1434, IEEE Guide to the Measurement of Partial Discharges in Rotating Machinery

IEEE 1458, RP for the Selection, Field Testing, and Life Expectancy of Molded Case Circuit
Breakers for Industrial Applications

IEEE 1531, Guide for Application and Specification of Harmonic Filters

IEEE 1566, Standard for Performance of Adjustable Speed AC Drives Rated at 375 kW & Larger

IEEE 1580, RP for Marine Cable for use on Shipboard and Fixed or Floating Platforms

IEEE 1580.1, RP for Insulated Bus Pipe for Use on Shipboard and Fixed or Floating Platforms

IEEE 1584, Guide for Performing Arc Flash Hazard Calculations

IEEE 1584.1, Guide for the Specification of Scope and Deliverable Requirements for an Arc-flash
Hazard Calculation Study in Accordance With IEEE 1584

IEEE 1584a, Guide for Performing Arc Flash Hazard Calculations Amendment 1

IEEE 1584b, Guide for Performing Arc Flash Hazard Calculations Amendment 2

IEEE 1588, Precision Clock Synchronization

IEEE 1662, Guide for the design and application of Power Electronics in Electrical Power Systems
on Ships

IEEE 1673, Standard for Requirements for Conduit & Cable Seals for Field Connected Wiring to
Equipment in Petroleum and Chemical Industry Exposed to pressures Above Atmospheric (1.5
kilopascals, 0.22 psi)

IEEE 1683, Guide for Motor Control Centers Rated up to and including 600 V AC or 1000 V DC
with Recommendations Intended to Help Reduce Electrical Hazards

IEEE 1709, RP for 1 to 35 KV Medium Voltage DC Power Systems on Ships

IEEE 1713, RP for Electrical Shore-to-Ship Connections (This work is done in IEC JWG 28, which
is responsible for the IEC/ISO/IEEE 80005-1 standard, see below)

IEEE 1714, RP for Industrial Uninterruptible (UPS) Systems

IEEE 1716, RP for Managing Natural Disaster Impact on key electrical systems and installation in
Petroleum and Chemical Facilities

IEEE 18, IEEE Standard for Shunt Power Capacitors

IEEE 1810, Guide for the Selection and Installation of Fire-Rated, Circuit Integrity Cables for
Safety, Critical, and Emergency Shutdown Systems in Petroleum and Chemical Industries

IEEE 1814, RP for Electrical System Design Techniques to Improve Electrical Safety
 Electrotechnical standards relevant for the oil and gas industry / 53

IEEE 1826, Standard for Power Electronics Open System Interfaces in Zonal Electrical Distribution
Systems Rated Above 100 kW

IEEE 242, RP for Protection and Coordination of Industrial and Commercial Power Systems

IEEE 252, Standard Test Procedure for Polyphase Induction Motors Having Liquid in the Magnetic
Gap

IEEE 303, RP for Auxiliary Devices for Rotating Electrical Machines in Class 1, Div 2 and Zone 2
Locations

IEEE 32, IEEE Standard Requirements, Terminology, and Test Procedures for Neutral Grounding
Devices

IEEE 383, Standard for Qualifying Class 1E Electric Cables and Field Splices for Nuclear Power
Generating Stations

IEEE 386, Standard for Separable Insulated Connector Systems for Power Distribution Systems
above 600 V

IEEE 421.2, RP for Excitation System Models for Power System Stability Studies

IEEE 421.5, RP for Excitation System Models for Power System Stability Studies

IEEE 43, IEEE RP for Testing Insulation Resistance of Electric Machinery

IEEE 446, RP for Emergency and Standby Power Systems for Industrial and Commercial
Applications

IEEE 446, RP for emergency and standby power systems for industrial and commercial
applications

IEEE 45, RP for Electric Installations on Shipboard

IEEE 45.1, RP for Electrical Installations on Shipboard 1 Design

IEEE 45.2, RP for Electrical Installations on Shipboard 2 Controls and Automation

IEEE 45.3, RP for Electrical Installations on Shipboard 3 Systems Integration

IEEE 45.4, RP for Electrical Installations on Shipboard 4 Marine Sectors and Mission Systems

IEEE 45.5, RP for Electrical Installations on Shipboard 5 Safety Considerations

IEEE 45.6, RP for Electrical Installations on Shipboard 6 Electrical Testing Installation and test
LV.

IEEE 45.7, RP for Electrical Installations on Shipboard 7 Switchboards

IEEE 45.8, RP for Electrical Installations on Shipboard 8 Cable Systems

IEEE 450, IEEE RP for Maintenance, Testing, and Replacement of Vented Lead-Acid Batteries for
Stationary Applications
 Electrotechnical standards relevant for the oil and gas industry / 54

IEEE 463, Std for Electrical Safety Practices in Electrolytic Cell line Working Zones

IEEE 484, RP for installation design and installation of vented lead-acid batteries for station
applications

IEEE 485, RP for the selection and sizing of lead-acid batteries for stationery applications

IEEE 515, Std for the Testing, Design, Installation, & Maintenance of Electrical Resistance Heat
Tracing for Industrial Applications

IEEE 518, Guide for the Installation of Electrical Equipment to Minimize Noise Inputs to Controllers
from External Sources,

IEEE 519, RP for IEEE Recommended Practices and Requirements for Harmonic Control in
Electrical Power Systems

IEEE 57.110, RP for Establishing Liquid-Filled and Dry-Type Power and Distribution Transformer
Capability When Supplying Nonsinusoidal Load Currents

IEEE 576, RP for Installation, Termination, & Testing of Insulated Power Cable as Used in
Industrial and Commercial Applications

IEEE 693, RP for Seismic Design of Substations

IEEE 762, IEEE Standard Definitions for Use in Reporting Electric Generating Unit Reliability,
Availability, and Productivity

IEEE 80, Approved Draft Guide for Safety in AC Substation Grounding

IEEE 802, IEEE Standard for Information technology--Telecommunications and information

exchange between systems Local and metropolitan area networks--Specific requirements

IEEE 802.11, IEEE Standard for Information technology--Telecommunications and information

exchange between systems Local and metropolitan area networks--Specific requirements Part 11:
Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications

IEEE 802.15.4, IEEE Standard for Local and metropolitan area networks--Part 15.4: Low-Rate
Wireless Personal Area Networks (LR-WPANs)

IEEE 802.16, IEEE Standard for Air Interface for Broadband Wireless Access Systems

IEEE 802.1ag, Connectivity Fault Management

IEEE 802.1ah, Provider Backbone Bridges

IEEE 802.1p, Traffic Prioritization 1998

IEEE 802.1q, Virtual Local Area Network (2012)

IEEE 802.1w, Rapid Spanning Tree Protocol (2004)

IEEE 802.1x, IEEE Standard for Local and metropolitan area networks--Port-Based Network
Access Control
 Electrotechnical standards relevant for the oil and gas industry / 55

IEEE 802.3, IEEE Standard for Ethernet

IEEE 802.3ad, Ethernet static link aggregation (2000)

IEEE 802.3af, Power-Over-Ethernet

IEEE 802.3at, Developed Power-Over-Ethernet

IEEE 841, Petroleum and Chemical Industry Premium- Efficiency, Severe-Duty, Totally Enclosed
Fan-Cooled (TEFC) Squirrel Cage Induction Motors Up to and Including 370 kW (500 hp)

IEEE 844, RP for Electrical Impedance, Induction, & Skin Effect Heating of Pipelines & Vessels

IEEE 844.1, Standard for the Construction, Testing, and Marking for Skin Effect Heating Systems
for Pipelines and Vessels

IEEE 844.2, Standard for the Construction, Testing, and Marking for Impedance, Induction, and
Inductions Susceptor Heating Systems for Pipelines and Vessels

IEEE 844.3, RP for Electrical Impedance, Induction & Skin Effect Heating Systems for Pipelines &
Vessel

IEEE 946, IEEE RP for the Design of DC Auxiliary Power Systems for Generating Systems

IEEE 979, Guide for Substation Fire Protection

IEEE 980, Guide for Containment and Control of Oil Spills in Substations

IEEE 998, Guide for Direct Lightning Stroke Shielding of Substations

IEEE C2, National Electrical Safety Code (NESC)

IEEE C37.010, Application Guide for AC High-Voltage Circuit Breakers Rated on a Symmetrical
Current Basis

IEEE C37.012, Guide for the Application of Capacitance Current Switching for AC High-Voltage
Circuit Breakers Above 1000 V

IEEE C37.101, Guide for Generator Ground Protection

IEEE C37.102, Guide for AC Generator Protection

IEEE C37.110, Guide for the Application of Current Transformers Used for Protective Relaying
Purposes

IEEE C37.111, Measuring relays and protection equipment Part 24: Common format for transient
data exchange (COMTRADE) for power systems

IEEE C37.13, Standard for Low-Voltage AC Power Circuit Breakers Used in Enclosures

IEEE C37.13.1, Standard for Definite Purpose Switching Devices for Use in Metal-Enclosed Low-
Voltage Power Circuit Breaker Switchgear
 Electrotechnical standards relevant for the oil and gas industry / 56

IEEE C37.16, Standard for Preferred Ratings, Related Requirements, and Application
Recommendations for Low-Voltage AC (635 V and below)and DC (3200 V and below) Power
Circuit Breakers

IEEE C37.17, Standard for Trip Systems for Low-Voltage (1000 V and below) AC and General
Purpose (1500 V and below) DC Power Circuit Breakers

IEEE C37.2, Standard Electrical Power System Device Function Numbers, Acronyms, and Contact
Designations

IEEE C37.20.1, Standard for Metal-Enclosed Low-Voltage Power Circuit Breaker Switchgear

IEEE C37.20.2, Standard for Metal-Clad Switchgear

IEEE C37.20.3, Standard for Metal-Enclosed Interrupter Switchgear (1 kV38 kV)

IEEE C37.20.7, Guide for Testing Metal-Enclosed Switchgear Rated Up to 38 kV for Internal
Arcing Faults

IEEE C37.21, Standard for Control Switchboards

IEEE C37.23, Metal-Enclosed Bus

IEEE C37.90, Standard for Relays and Relay Systems Associated with Electric Power Apparatus

IEEE C37.90.1, Standard for Surge Withstand Capability (SWC) Tests for Relays and Relay
Systems Associated with Electric Power Apparatus

IEEE C37.90.2, Standard for Withstand Capability of Relay Systems to Radiated Electromagnetic
Interference from Transceivers

IEEE C37.91, Guide for Protecting Power Transformers

IEEE C37.96, Guide for AC Motor Protection

IEEE C37.99, Guide for the Protection of Shunt Capacitor Banks

IEEE C50.13, Standard for Cylindrical-Rotor 50 Hz and 60 Hz Synchronous Generators Rated 10

MVA and Above

IEEE C57.106, Guide for Acceptance and Maintenance of Insulating Oil in Equipment

IEEE C57.110, RP for Establishing Liquid-Filled and Dry-Type Power and Distribution Transformer
Capability When Supplying Nonsinusoidal Load Currents

IEEE C57.111, Guide For Acceptance Of Silicone Insulating Fluid And Its Maintenance In
Transformers

IEEE C57.12.00, General Requirements for Liquid-Immersed Distribution, Power, and Regulating
Transformers

IEEE C57.12.01, General Requirements for Dry-Type Distribution and Power Transformers,
Including Those with Solid-Cast and/or Resin Encapsulated Windings
 Electrotechnical standards relevant for the oil and gas industry / 57

IEEE C57.12.90, Test Code for Liquid-Immersed Distribution, Power, and Regulating Transformers

IEEE C57.12.91, Test Code for Dry-Type Distribution and Power Transformers

IEEE C57.121, Guide For Acceptance And Maintenance Of Less-Flammable Hydrocarbon Fluid In
Transformers

IEEE C57.13, Standard Requirements for Instrument Transformers

IEEE C57.131, Requirements for Load Tap Changers

IEEE C57.18.10, Practices and Requirements for Semiconductor Power Rectifier Transformers

IEEE C57.19.00, General Requirements and Test Procedure for Power Apparatus Bushings

IEEE C57.91 Guide For Loading Mineral-Oil-Immersed Overhead Type Distribution Transformers
With 55C Or 65C Average Winding Rise.

IEEE C57.92, Guide For Loading Mineral-Oil-Immersed Power Transformers Up To And Including
100MVA With 55C Or 65C Average Winding Rise.

IEEE C57.94, Recommended Practices For Installation, Application, Operation And Maintenance
Of Dry-Type General Purpose Distribution And Power Transformers.

IEEE C57.96, Guide For Loading Dry-Type Transformers, Appendix To C57.12 Standards

IEEE C62.1, Standard for Gapped Silicon-Carbide Surge Arresters for AC Power Circuits.

IEEE C62.41, IEEE RP on Surge Voltages in Low-Voltage AC Power Circuits

IEEE C95.1, IEEE Standard for Safety Levels with Respect to Human Exposure to Radio
Frequency Electromagnetic Fields, 3 kHz to 300 GHz

IEC/ISO/IEEE 80005-1, Utility connections in port Part 1: High voltage shore connection (HVSC)
Systems General requirements
 Electrotechnical standards relevant for the oil and gas industry / 58

NEMA National Electrical Manufacturers

Association
NEMA BU 1, Busways

NEMA C37.50, Low-Voltage AC Power Circuit Breakers Used in EnclosuresTest Procedures

NEMA C80.1, Electrical Rigid Steel Conduit (ERSC)

NEMA CC 1, Electric Power Connection for Substations

NEMA FG 1, Fiberglass Cable Tray Systems

NEMA FG1, Fiberglass Cable Tray Systems

NEMA FU 1, Low Voltage Cartridge Fuses

NEMA IA 2.2, Programmable ControllersPart 2: Equipment Requirements and Tests

NEMA IA 2.3, Programmable ControllersPart 3: Programming Languages

NEMA ICS 1, Industrial Control and Systems: General Requirements

NEMA ICS 10, Industrial Control and Systems

NEMA ICS 10, Industrial Control and Systems Part 1: Electromechanical AC Transfer Switch
Equipment

NEMA ICS 18, Motor Control Centers

NEMA ICS 2, Industrial Control and Systems: Controllers, Contactors and Overload Relays Rated
600 Volts

NEMA ICS 3, Industrial Control and Systems: Medium Voltage Controllers Rated 2001 to 7200
Volts AC

NEMA ICS 4, Application Guideline for Terminal Blocks

NEMA ICS 5, Industrial Control and Systems Control-Circuit and Pilot Devices

NEMA ICS 6, Industrial Controls and Systems: Enclosures

NEMA ICS 7, Industrial Control and Systems: Adjustable-Speed Drives

NEMA ICS 7.1, Safety Standards for Construction and Guide for Selection, Installation, and
Operation of Adjustable-Speed Drive Systems

NEMA MG 1, Information Guide for General Purpose Industrial AC Small and Medium Squirrel-
Cage Induction Motor Standards
 Electrotechnical standards relevant for the oil and gas industry / 59

NEMA MG 2, Safety Standard for Construction and Guide for Selection, Installation, and Use of
Electric Motors and Generators

NEMA MG 3, Sound Level Prediction for Installed Rotating Electrical Machines

NEMA MW 1000, Magnet Wire

NEMA PB 1, Panelboards

NEMA PB 2, Deadfront Distribution Switchboards

NEMA PB 2.2, Application Guide for Ground Fault Protective Devices for Equipment

NEMA PE 1, Uninterruptible power systems

NEMA PE 5, Utility Type Battery Chargers

NEMA PE 7, Communication Type Battery Chargers

NEMA PE1, Uninterruptible Power Systems (UPS) Specification and Performance Verification

NEMA RN 1, Polyvinyl-Chloride (PVC) Externally Coated Galvanized Rigid Steel Conduit and
Intermediate Metal Conduit

NEMA SG 4, Alternating-Current High-Voltage Circuit Breakers

NEMA SM 23, Steam Turbines for Mechanical Drive Service

NEMA ST 20, Dry-Type Transformers for General Applications

NEMA STD 250, Enclosures for Electrical Equipment (1000 Volts Maximum)

NEMA TC 2, Electrical Polyvinyl Chloride (PVC) Conduit

NEMA TC 3, Polyvinyl Chloride (PVC) Fittings for Use with Rigid PVC Conduit and Tubing

NEMA TC 6 & 8, Polyvinyl Chloride (PVC) Plastic Utilities Duct for Underground Installations

NEMA TC 9, Fittings for Polyvinyl Chloride (PVC) Plastic Utilities Duct for Underground Installation

NEMA TCB2, Guidelines for the Selection and Installation of Underground Nonmetallic Raceways

NEMA TP 1, Guide for Determining Energy Efficiency for Distribution Transformers

NEMA TR 1, Transformers, Step Voltage Regulators and Reactors

NEMA VE 1, Metal Cable Tray Systems

NEMA VE 2, Cable Tray Installation Guidelines

NEMA WC 26, Binational Wire and Cable Packaging Standard

NEMA WC 51, Ampacities of Cables Installed in Cable Trays

 Electrotechnical standards relevant for the oil and gas industry / 60

NEMA WD 6 , Wiring Devices Dimensional Specifications

NEMA Z535.1, Safety Colors

NEMA Z535.2, Environmental and Facility Safety Signs

NEMA Z535.3, Criteria for Safety Symbols

NEMA Z535.4, Product Safety Signs and Labels

 Electrotechnical standards relevant for the oil and gas industry / 61

NFPA codes & standards

NFPA 37, Standard for the Installation and Use of Stationary Combustion Engines and Gas
Turbines

NFPA 70, National Electrical Code

NFPA 70B, Recommended Practice for Electrical Equipment Maintenance

NFPA 70E, Standard for Electrical Safety in the Workplace

NFPA 72, National Fire Alarm and Signaling Code

NFPA 77, RP on Static Electricity

NFPA 110, Standard for Emergency and Standby Power Systems

NFPA 111, Standard on Stored Electrical Energy Emergency and Standby Power Systems

NFPA (FIRE) 496, Standard for Purged and Pressurized Enclosures for Electrical Equipment

NFPA 496, RP for the Classification of Flammable Liquids, Gases, or Vapors and of Hazardous
(Classified) Locations for Electrical Installations in Chemical Process Areas

NFPA 497, Classification of Flammable Liquids, Gases, or Vapours and of Hazardous (Classified)
Locations for Electrical Installations in Chemical Process Areas

NFPA 499, Classification of Combustible Dusts and of Hazardous (Classified) Locations for
Electrical Installations in Chemical Process Areas,

NFPA 780, Standard for the Installation of Lightning Protection Systems

NFPA 850, RP for Fire Protection for Electric Generating Plants and High Voltage Direct Current
Converter Stations
 Electrotechnical standards relevant for the oil and gas industry / 62

EEMUA publications
EEMUA 107, Recommendations For The Protection Of Diesel Engines For Use In Zone 2
Hazardous Areas

EEMUA 133, Specification for Underground Armoured Cable Protected against Solvent
Penetration and Corrosive Attack

EEMUA 181, A Guide to Risk Based Assessments of In-situ Large Ex 'e' and Ex 'N' Machines

EEMUA 186, A Practitioner's Handbook - Electrical Installation, Inspection and Maintenance in

Potentially Explosive Atmospheres
 Electrotechnical standards relevant for the oil and gas industry / 63

UL standards
UL 10B, Fire Tests of Door Assemblies

UL 1008, Transfer Switch Equipment

UL 1203, Standard for Safety Explosion-Proof and Dust-Ignition-Proof Electrical Equipment for Use
in Hazardous (Classified) Locations

UL 1030, Sheathed Heating Elements

UL 1053, Ground-Fault Sensing and Relaying Equipment

UL 1072, Standard for Safety Medium-Voltage Power Cables

UL 1203, UL Standard for Safety Explosion-Proof and Dust-Ignition-Proof Electrical Equipment for
Use in Hazardous (Classified) Locations

UL 1247, Diesel Engines for Driving Stationary Fire Pumps

UL 1277, Electrical Power and Control Tray Cables with Optional Optical-Fiber Members

UL 13, Power-Limited Circuit Cables

UL 1316, Glass-Fiber-Reinforced Plastic Underground Storage Tanks for Petroleum Products,

Alcohols, and Alcohol-Gasoline Mixtures

UL 139, Outline of Investigation for Medium- and High-Expansion Foam-Extinguishing System

Equipment and Concentrates

UL 142, Safety Steel Aboveground Tanks for Flammable and Combustible Liquids

UL 1479, Fire Tests of Through-Penetration Firestops

UL 1480, Speakers for Fire Alarm, Emergency, and Commercial and Professional Use

UL 154, Standard for Safety Carbon-Dioxide Fire Extinguishers

UL 1558, Metal-Enclosed Low-Voltage Power Circuit Breaker Switchgear

UL 1569, Standard for Safety Metal-Clad Cables

UL 1581, Reference Standard for Electrical Wires, Cables, and Flexible Cords

UL 162, Standard for Safety for Foam Equipment and Liquid Concentrates

UL 1651, UL Standard for Safety Optical Fiber Cable

UL 1682, UL Standard for Safety Plugs, Receptacles, and Cable Connectors of the Pin and Sleeve
Type
 Electrotechnical standards relevant for the oil and gas industry / 64

UL 1709, Rapid Rise Fire Tests of Protection Materials for Structural Steel

UL 174 , Safety Household Electric Storage Tank Water Heaters

UL 1778, Uninterruptible Power Systems

UL 181, UL Standard for Safety Factory-Made Air Ducts and Connectors

UL 199, Automatic Sprinklers for Fire-Protection Service

UL 218, Fire Pump Controllers

UL 2196, Tests for Fire Resistive Cables

UL 2225, Cables and Cable-Fittings For Use In Hazardous (Classified) Locations

UL 2250, Instrumentation Tray Cable

UL 263, Fire Tests of Building Construction and Materials

UL 299 , Safety Dry Chemical Fire Extinguishers

UL 347 , UL Standard for Safety Medium-Voltage AC Contactors, Controllers, and Control Centers

UL 363, Knife Switches

UL 44, Thermoset-Insulated Wires and Cables

UL 444, Communications Cables

UL 467, Grounding and Bonding Equipment

UL 489, Molded-Case Circuit Breakers, Molded-Case Switches and Circuit-Breaker Enclosures

UL 497, Protectors for Paired-Conductor Communications Circuits

UL 497A, Standard for Safety Secondary Protectors for Communication Circuits

UL 497B, Protectors for Data Communications and Fire-Alarm Circuits

UL 508, Industrial Control Equipment

UL 67, Panelboards

UL 674, Electric Motors and Generators for Use in Division 1 Hazardous (Classified) Locations

UL 711, Rating and Fire Testing of Fire Extinguishers

UL 779, Standard for Safety for Electrically Conductive Floorings

UL 796, Printed-Wiring Boards

UL 83, Thermoplastic-Insulated Wires and Cables

 Electrotechnical standards relevant for the oil and gas industry / 65

UL 845, Standard for Safety for Motor Control Centers

UL 886, Outlet Boxes and Fittings for Use in Hazardous (Classified) Locations

UL 891, Standard for Safety Switchboards

UL 894, Switches For Use In Hazardous (Classified) Locations

UL 913, Intrinsically Safe Apparatus and Associated Apparatus for Use in Class I, II, and III,
Division 1, Hazardous (Classified) Locations

UL 924, The Standard for Safety of Emergency Lighting and Power Equipment

UL 94, The Standard for Safety of Flammability of Plastic Materials for Parts in Devices and
Appliances testing

UL 96, Lightning Protection Components

UL 96A, Standard for Safety Installation Requirements for Lightning Protection Systems

UL 98, Enclosed and Dead-Front Switches

 Electrotechnical standards relevant for the oil and gas industry / 66

Classification societys standards

ABS Guide for building and classing Facilities on offshore installations

ABS Guidance Notes for the Application of Ergonomics to Marine Systems

BV NR 428 Electrical systems on board offshore units and installations

DNV-OS-E101 Offshore standard Drilling plant

DNV-OS-D201 Offshore standard Electrical installations

LR Rules and regulations for the classification of a floating offshore installation at a fixed location
Part 6 Control and electrical engineering

IACS International Association of Classification Societies:

UR_E_150 Unified Requirements Electrical System

REC_35 Unified Recommendation

 Electrotechnical standards relevant for the oil and gas industry / 67

Energy Institute documents

EI 1 Model Code of Safe Practice Part 1: The selection, installation, inspection, and maintenance
of electrical and non-electrical apparatus in hazardous areas

EI 15 Model Code of Safe Practice Part 15: Area Classification Code for Installations Handling
Flammable Fluids

EI 21 Model Code of Safe Practice Part 21: Guidelines for the control of hazards arising from static
electricity

EI Design and operational guidance on cathodic protection of offshore structures, subsea

installations and pipelines

EI Controlling the risks from static electricity

EI Electrical Committee Fault code matrix

EI Guidelines for managing inspection of Ex electrical equipment ignition risk in support of IEC
60079-17

EI Guidance on assessing the safety integrity of electrical supply protection

EI Guidelines for offshore oil and gas installations that are not permanently attended

API/EI Research report: Verification of lightning protection requirements for above ground
hydrocarbon storage tanks
 Electrotechnical standards relevant for the oil and gas industry / 68

EN standards
EN 1127-1, Explosive atmospheres Explosion prevention and protection Part 1: Basic concepts
and methodology

EN 1839, Determination of explosion limits of gases and vapours

EN 13237, Potentially explosive atmospheres Terms and definitions for equipment and protective
systems intended for use in potentially explosive atmospheres

EN 13463-1, Non-electrical equipment for use in potentially explosive atmospheres Part 1: Basic
method and requirements

EN 13463-2, Non-electrical equipment for use in potentially explosive atmospheres Part 2:

Protection by flow restricting enclosure 'fr'

EN 13463-3, Non-electrical equipment for use in potentially explosive atmospheres Part 3:

Protection by flameproof enclosure 'd'

EN 13463-5, Non-electrical equipment intended for use in potentially explosive atmospheres Part
5: Protection by constructional safety 'c'

EN 13463-6, Non-electrical equipment for use in potentially explosive atmospheres Part 6:

Protection by control of ignition source 'b'

EN 13463-8, Non-electrical equipment for potentially explosive atmospheres Part 8: Protection

by liquid immersion 'k'

EN 13821, Potentially explosive atmospheres Explosion prevention and protection

Determination of minimum ignition energy of dust/air mixtures

EN 14460, Explosion resistant equipment

EN 14522, Determination of the auto ignition temperature of gases and vapours

EN 14591-1, Explosion prevention and protection in underground mines Protective systems

Part 1: 2-bar explosion proof ventilation structure

EN 14797, Explosion venting devices

EN 14986, Design of fans working in potentially explosive atmospheres

EN 14994, Gas explosion venting protective systems

EN 15089, Explosion isolation systems

EN 15198, Methodology for the risk assessment of non-electrical equipment and components for
intended use in potentially explosive atmospheres
 Electrotechnical standards relevant for the oil and gas industry / 69

EN 15233, Methodology for functional safety assessment of protective systems for potentially
explosive atmospheres

EN 15794, Determination of explosion points of flammable liquids

EN 16009, Flameless explosion venting devices

EN 16020, Explosion diverters

EN 50110, Operation of electrical installations

EN 50172, Code of practice for emergency lighting

EN 50495, Safety devices required for the safe functioning of equipment with respect to explosion
risks

EN 60079-0, Explosive atmospheres Part 0: Equipment General requirements

EN 60079-1, Explosive atmospheres Part 1: Equipment protection by flameproof enclosures "d"

EN 60079-2, Explosive atmospheres Part 2: Equipment protection by pressurized enclosure "p"

EN 60079-5, Explosive atmospheres Part 5: Equipment protection by powder filling "q"

EN 60079-6, Explosive atmospheres Part 6: Equipment protection by oil immersion "o"

EN 60079-7, Explosive atmospheres Part 7: Equipment protection by increased safety "e"

EN 60079-11, Explosive atmospheres Part 11: Equipment protection by intrinsic safety "i"

EN 60079-15, Explosive atmospheres Part 15: Equipment protection by type of protection "n"

EN 60079-18, Explosive atmospheres Part 18: Equipment protection by encapsulation "m"

EN 60079-20-1, Explosive atmospheres Part 20-1: Material characteristics for gas and vapour
classification Test methods and data

EN 60079-25, Explosive atmospheres Part 25: Intrinsically safe electrical systems

EN 60079-26, Explosive atmospheres Part 26: Equipment with equipment protection level (EPL)
Ga

EN 60079-11, Explosive atmospheres Part 11: Equipment protection by intrinsic safety i

EN 60079-28, Explosive atmospheres Part 28: Protection of equipment and transmission

systems using optical radiation

EN 60079-29-1, Explosive atmospheres Part 29-1: Gas detectors Performance requirements of

detectors for flammable gases

EN 60079-29-4, Explosive atmospheres Part 29-4: Gas detectors Performance requirements of

open path detectors for flammable gases
 Electrotechnical standards relevant for the oil and gas industry / 70

EN 60079-30-1, Explosive atmospheres Part 30-1: Electrical resistance trace heating General
and testing requirements

EN 60079-30-2, Explosive atmospheres Part 30-2: Electric surface heating

EN 60079-31, Explosive atmospheres Part 31: Equipment dust ignition protection by enclosure
"t"

EN (IEC) 60801-2, Electromagnetic compatibility for industrial-process measurement and control

equipment Electrostatic discharge requirements

EN 61000-6-1,2, Electromagnetic compatibility Generic immunity standard.

EN 61000-6-3,4, Electromagnetic compatibility Generic emission standard.

EN 61439, Low-voltage switchgear and controlgear assemblies

EN 62305, Code of practice for protection of structures against lightning

EN ISO/IEC 80079-34, Explosive atmospheres Part 34: Application of quality systems for
equipment manufacture
 Electrotechnical standards relevant for the oil and gas industry / 71

GSO Electrotechnical standards

GSO 1054, Power cables with extruded insulation and their accessories for rated voltages from 1
kV (Um = 1.2 kV) up to 30 kV (Um = 36 kV) Part 2: Cables for rated voltages from 6 kV (Um =
7.2 kV) up to 30 kV (Um = 36 kV)

GSO 1511, Electrical test methods for electric cables Part 2: Partial discharge tests

GSO 1518, Power transformers Part 3: Insulation levels and dielectric test Section 1: External
clearances in air

GSO 1519, Low-voltage switchgear and control gear assemblies Part 1: Type-tested and
partially type-tested assemblies

GSO 1539, Electrical installations of buildings Part 3: Assessment of general characteristics

GSO 1549, Power transformers Part 2: Temperature rise

GSO 1571, Overhead electrical conductors Calculation methods for stranded bare conductors

GSO 1899, GCC Standard voltages and frequencies for A-C transmission and distribution systems

GSO 195, Methods of test for adhesive insulating tapes for electrical purposes

GSO 218, Industrial safety and health regulations Electrical Part 2: Low Voltage

GSO 233, Testing methods for power transformers

GSO 32, Methods of testing plastic conduits and fittings for electrical installations

GSO 33, Plastic conduits and fittings for electrical installations

GSO 60811-4-2, Insulating and sheathing materials of electric and optical cables Common test
methods Part 4-2: Methods specific to polyethylene and polypropylene compounds

GSO 73, Industrial safety and health regulations Electrical Part 1: Terms and definitions

GSO 78, Industrial safety and health regulations electrical Part4: illumination

GSO 902, Additional requirements for enclosed switch gear and control gear for 1 kV to 72.5 kV to
be used in severe climatic conditions.

GSO 920, Tests for power cables with extruded insulation for rated voltages above 30 kV (Um = 36
kV) up to 150 kV (Um = 170 kV)
 Electrotechnical standards relevant for the oil and gas industry / 72

Other relevant codes, documents &

standards
ASTM F 1166, Standard Practice for Human Engineering Design for Marine Systems, Equipment
and Facilities

ASTM F 1337, Standard Practice for Human Engineering Program Requirements for Ships and
Marine Systems, Equipment and Facilities

CAP 437, Offshore Helicopter Landing Areas Guidance on Standards (UK Civil Aviation
Authority)

IALA Recommendation E-200-0, Marine Signal Lights

IALA Recommendation E-200-1, Marine Signal Lights Part 1: Colours

IALA Recommendation E-200-2, Marine Signal Lights Part 2: Calculation, Definition and Notation
of Luminous Range

IALA Recommendation E-200-3, Marine Signal Lights Part 3: Measurement

IALA Recommendation E-200-4, Marine Signal Lights Part 4: Determination and Calc. of
Effective Intensity

IALA Recommendation O-114, Recommendation on the marking of offshore structures

IALA Recommendation O-139, Marking of Man-Made Offshore Structures

ICAO Aereodromes, Annex 14 Volume II - Heliports

IEE Recommendations for the Electrical and Electronic Equipment of Mobile and Fixed Offshore
Installations

IMO Guidelines for ships operating in polar waters.

IMO COLREG Convention on the International Regulations for Preventing Collisions at SEA

IMO SOLAS (International Convention for the Safety of Life at Sea)

IMO Mobile Offshore Drilling units (IMO MODU CODE)

ISGOTT International Oil Tanker and Terminal Safety Guide (ICS, OCIMF and IAPH)

ISGOTT was first published in 1978 and combined the contents of the Tanker Safety
Guide (Petroleum), published by the International Chamber of Shipping (ICS), and the
International Oil Tanker and Terminal Safety Guide, by the Oil Companies
International Marine Forum (OCIMF). In producing the Fifth Edition, the content has
again been reviewed by these ICS and OCIMF, together with the International
 Electrotechnical standards relevant for the oil and gas industry / 73

Association of Ports and Harbors (IAPH), to ensure that it continues to reflect current
best practice and legislation.

ISO 10816-1, Mechanical vibration Evaluation of machine vibration by measurements on non-

rotating parts Part 1: General guidelines

ISO 6592, Information technology Guidelines for the documentation of computer-based

application systems

ISO 7919-1, Mechanical vibration of non-reciprocating machines Measurements on rotating

shafts and evaluation criteria Part 1: General guidelines

ISO 8528-5, Reciprocating internal combustion engine driven alternating current generating sets
Part 5: Generating sets

ISO 13702, Control and Mitigation of Fires and Explosions on Offshore Production Installations

ISO 15138, Offshore Production Installations Heating, Ventilation, Air Conditioning

ISO 21789, Gas Turbine Applications Safety

MARPOL Guidelines for implementation of energy efficiency measures adopted

The Marine Environment Protection Committee (MEPC in IMO) adopted four sets of guidelines
intended to assist in the implementation of the mandatory Regulations on Energy Efficiency for
Ships in MARPOL Annex VI, which are expected to enter into force on 1 January 2013:

2012 Guidelines on the method of calculation of the attained Energy Efficiency Design
Index (EEDI) for new ships;

2012 Guidelines for the development of a Ship Energy Efficiency Management Plan
(SEEMP);

2012 Guidelines on survey and certification of the Energy Efficiency Design Index
(EEDI); and

Guidelines for calculation of reference lines for use with the Energy Efficiency Design
Index (EEDI).

NEK 606 (Cables for offshore installations

NORSOK E-001 Electrical systems

Oil & Gas UK HS028 Guidelines for management of electrical operations

Oil & Gas UK HS084 Guidance on Ageing and Life Extension Aspects of Electrical, Control &
Instrumentation Equipment, Issue 1, May 2014

UK HSE Approved Code of Practice L138 Dangerous substances and explosive atmospheres.
 Electrotechnical standards relevant for the oil and gas industry / 74

UK HSE has issued a great number of Code of Practices, Guidelines and publications on electrical
systems

USCG 33 CFR Part 67 Aids to navigation on artificial islands and fixed structures.