Magelis GTO

EIO0000001133 02/2012

Magelis GTO
User Manual
02/2012
EIO0000001133 00

www.schneider-electric.com
 The information provided in this documentation contains general descriptions and/or technical character-
istics of the performance of the products contained herein. This documentation is not intended as a
substitute for and is not to be used for determining suitability or reliability of these products for specific
user applications. It is the duty of any such user or integrator to perform the appropriate and complete
risk analysis, evaluation and testing of the products with respect to the relevant specific application or use
thereof. Neither Schneider Electric nor any of its affiliates or subsidiaries shall be responsible or liable for
misuse of the information contained herein. If you have any suggestions for improvements or
amendments or have found errors in this publication, please notify us.
No part of this document may be reproduced in any form or by any means, electronic or mechanical,
including photocopying, without express written permission of Schneider Electric.
All pertinent state, regional, and local safety regulations must be observed when installing and using this
product. For reasons of safety and to help ensure compliance with documented system data, only the
manufacturer should perform repairs to components.
When devices are used for applications with technical safety requirements, the relevant instructions must
be followed.
Failure to use Schneider Electric software or approved software with our hardware products may result
in injury, harm, or improper operating results.
Failure to observe this information can result in injury or equipment damage.
2012 Schneider Electric. All rights reserved.

2 EIO0000001133 02/2012
 Table of Contents

Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
About the Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Chapter 1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Magelis GTO Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Certifications and Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Magelis GTO Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Chapter 2 Device Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
System Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Chapter 3 Parts Identification and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Parts Identification and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Chapter 4 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.1 HMIGTO1300/1310 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Electrical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Structural Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Display Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Memory, Clock, Touch Panel and Function Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Interface Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Specifications of Serial Interface COM1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Specifications of Serial Interface COM2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4.2 HMIGTO2300/2310/2315 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Electrical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Structural Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Display Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Memory, Clock, and Touch Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Interface Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Specifications of Serial Interface COM1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Specifications of Serial Interface COM2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
4.3 HMIGTO3510/4310 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Electrical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Structural Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Display Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Memory, Clock, Touch Panel, and Function Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Interface Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Specifications of Serial Interface COM1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Specifications of Serial Interface COM2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
4.4 HMIGTO5310/5315 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Electrical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Structural Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Display Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Memory, Clock, and Touch Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Interface Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Specifications of Serial Interface COM1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Specifications of Serial Interface COM2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

EIO0000001133 02/2012 3
 4.5 HMIGTO6310/6315 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Environmental Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Structural Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Display Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Memory, Clock, and Touch Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Interface Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Specifications of Serial Interface COM1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Specifications of Serial Interface COM2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Chapter 5 Installation and Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
5.1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Installation Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
5.2 Wiring Principles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Connecting the Power Cord. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Connecting the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
5.3 SD Card Insertion/Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Inserting the SD Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Removing the SD Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
SD Card Data Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
5.4 USB Cable Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
USB Cable Clamp for USB (Type A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
USB Holder for USB (mini-B). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Chapter 6 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Regular Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Replacing the Installation Gasket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Periodic Check Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Replacing the Primary Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141

4 EIO0000001133 02/2012
 Safety Information

Important Information

NOTICE
Read these instructions carefully, and look at the equipment to become familiar with the device before
trying to install, operate, or maintain it. The following special messages may appear throughout this
documentation or on the equipment to warn of potential hazards or to call attention to information that
clarifies or simplifies a procedure.

PLEASE NOTE
Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel.
No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this
material.
A qualified person is one who has skills and knowledge related to the construction and operation of
electrical equipment and its installation, and has received safety training to recognize and avoid the
hazards involved.

EIO0000001133 02/2012 5
6 EIO0000001133 02/2012
 About the Book

At a Glance

Document Scope
This document describes how to use the Magelis GTO.

Validity Note
This document is valid for Magelis GTO with Vijeo Designer version 6.1.0 or later.
The technical characteristics of the device(s) described in this manual also appear online. To access this
information online:

Step Action
1 Go to the Schneider Electric home page www.schneider-electric.com.
2 In the Search box type the model number of a product or the name of a product
range.
z Do not include blank spaces in the model number/product range.
z To get information on a grouping similar modules, use asterisks (*).

3 If you entered a model number, go to the Product datasheets search results

and click on the model number that interests you.
If you entered the name of a product range, go to the Product Ranges search
results and click on the product range that interests you.
4 If more than one model number appears in the Products search results, click on
the model number that interests you.
5 Depending on the size of your screen, you may need to scroll down to see the
data sheet.
6 To save or print a data sheet as a .pdf file, click Download XXX product
datasheet.

The characteristics presented in this manual should be the same as those that appear online. In line with
our policy of constant improvement we may revise content over time to improve clarity and accuracy. In
the event that you see a difference between the manual and online information, use the online information
as your reference.

Product Related Information

WARNING
UNINTENDED EQUIPMENT OPERATION
The application of this product requires expertise in the design and programming of control systems.
Only persons with such expertise should be allowed to program, install, alter, and apply this product.
Follow all local and national safety codes and standards.
Failure to follow these instructions can result in death, serious injury, or equipment damage.

User Comments
We welcome your comments about this document. You can reach us by e-mail at techcomm@schneider-
electric.com.

EIO0000001133 02/2012 7
8 EIO0000001133 02/2012
 Magelis GTO
Overview
EIO0000001133 02/2012

Overview

1
Overview
This chapter describes the panels and general topics such as package contents and standards.

Whats in this Chapter?

This chapter contains the following topics:
Topic Page
Magelis GTO Package Contents 10
Certifications and Standards 11
Magelis GTO Panels 12

EIO0000001133 02/2012 9
Overview

Magelis GTO Package Contents

Overview
Verify all items listed here are present in your package:

1 2
For Magelis GTO For HMIGTO2315/5315/6315
except HMIGTO2315/5315/6315

3 4 5
For Magelis GTO For HMIGTO2315/5315/6315 For HMIGTO2315/5315/6315
except HMIGTO2315/5315/6315

6 7 8
For Magelis GTO
except
HMIGTO5310/5315/6310/6315

For HMIGTO5310/5315
For HMIGTO6310/6315

1 Magelis GTO: 1
2 Installation gasket: 1 (attached to the panel)
3 Installation fasteners: 4 per set
4 Brackets: 4
5 M4 Hex Nuts: 8
6 DC power connector: 1*1
7 USB cable clamp Type A: 1 set (1 clip and 1 tie)
8 USB cable clamp mini-B: 1 (1 USB holder)
9 Magelis GTO Quick Reference Guide: 1
This product has been carefully packed with special attention to quality. However, should you find
anything damaged or missing, contact your local distributor.
*1
You can use the DC power connector for HMIGTO1300/1310/2300/2310/2315/3510/4310 to supply
power to HMIGTO5310/5315/6310/6315. However the reverse is not possible. You cannot use the power
connector for HMIGTO5310/5315/6310/6315 on HMIGTO1300/1310/2300/2310/2315/3510/4310.

Revision
You can identify the product version (PV), revision level (RL) and the software version (SV) from the unit
product label.

10 EIO0000001133 02/2012
 Overview

Certifications and Standards

Introduction
Schneider Electric submitted this product for independent testing and qualification by third-party listing
agencies. These agencies have certified this product as meeting the following standards.

Agency Certifications
The Magelis GTO is certified by the Underwriters Laboratory according to:
z UL 508 and CSA C22.2 n142 for Industrial Control Equipment
Refer to the Schneider Electric web site for installation guidelines.
For detailed information, contact your local distributor or see the catalog & marking on the product.

Hazardous Substances
The Magelis GTO is designed for compliance with:
z WEEE, Directive 2002/96/EC
z RoHS, Directive 2002/95/EC
z RoHS China, Standard SJ/T 11363-2006

CE Markings
This product conforms to the necessary requirements of the following Directives for applying the CE label:
z 2006/95/EC Low Voltage Directive
z 2004/108/EC EMC Directive

This conformity is based on compliance with EN61000-6-4, EN61000-6-2 .

WARNING
RISK OF EXPLOSION IN HAZARDOUS LOCATIONS
z Verify that the power, input and output (I/O) wiring are in accordance with Class I, Division 2 wiring
methods.
z Do not substitute components that may impair compliance to Class I, Division 2.
z Do not connect or disconnect equipment unless power has been switched off or the area is known
to be non-hazardous.
z Securely lock externally connected units and each interface before turning on the power supply.
z Do not use, connect, or disconnect USB (mini-B) cable connections in hazardous locations. USB
(mini-B) interface is for temporary connection only during maintenance and setup.
Failure to follow these instructions can result in death, serious injury, or equipment damage.

WARNING
RISK OF EXPLOSION IN HAZARDOUS LOCATIONS
z Do not disconnect while circuit is live or unless the area is known to be free of ignitable
concentrations.
z Potential electrostatic charging hazard: wipe the front panel of the terminal with a damp cloth before
turning ON.
Failure to follow these instructions can result in death, serious injury, or equipment damage.

KC Markings

G
G
GGG G G G G GG
G G
hGG G G OhPG G G G G
OGPG GGGSGGGGG
G GUG
G
G
G

EIO0000001133 02/2012 11
Overview

Magelis GTO Panels

Critical systems, alarms and handling Requirements

Critical alarm indicators and system functions require independent and redundant protection hardware
and/or mechanical interlocks.
When you cycle power, wait at least 10 seconds before restoring the power to the panel after it has been
turned off. Switching the power OFF and ON quickly can damage the panel.
In the event the screen cannot be properly read, for example, if the backlight is not functioning, it may be
difficult or impossible to identify a function. Functions that may present a hazard if not immediately
executed, such as a fuel shut-off, must be provided independently of the panel. The machines control
system design must take into account the possibility of the backlight no longer functioning and the
operator being unable to control the machine or making mistakes in the control of the machine.

WARNING
LOSS OF CONTROL
z Consider the potential failure modes of control paths in the machine control system design, such as:
z the possibility of backlight failure,
z unanticipated link transmission delays or failures,
z the operator being unable to control the machine,
z the operator making errors in the control of the machine.

z Provide a means to achieve a safe state during and after a path failure for critical control functions
such as emergency stop and overtravel stop.
z Provide separate or redundant control paths for critical control functions.
z Test individually and thoroughly each implementation of the panel for correct operation before
service.
Failure to follow these instructions can result in death, serious injury, or equipment damage.

For additional information, refer to NEMA ICS 1.1 (latest edition), "Safety Guidelines for the Application,
Installation, and Maintenance of Solid State Control" and to NEMA ICS 7.1 (latest edition), "Safety
Standards for Construction and Guide for Selection, Installation and Operation of Adjustable-Speed Drive
Systems" or their equivalent governing your particular location.

WARNING
UNINTENDED EQUIPMENT OPERATION
z Do not use this equipment as the only means of control for critical system functions such as motor
start/stop or power disconnect.
z Do not use this equipment as the only notification device for critical alarms, such as device
overheating or overcurrent.
Failure to follow these instructions can result in death, serious injury, or equipment damage.

Handling the LCD panel

The following characteristics are specific to the LCD panel and are considered normal behavior:
z LCD screen may show unevenness in the brightness of certain images or may appear different when
seen from outside the specified viewing angle. Extended shadows, or crosstalk may also appear on
the sides of screen images.
z LCD screen pixels may contain black and white colored spots and color display may seem to have
changed.
z When the same image is displayed on the screen for a long period, an afterimage may appear when
the image is changed. If this happens, turn OFF the panel, wait 10 seconds and then restart the panel.
NOTE: Change the screen image periodically and try not to display the same image for a long period of
time.

12 EIO0000001133 02/2012
 Overview

CAUTION
SERIOUS EYE AND SKIN INJURY
The liquid in the LCD panel contains an irritant:
z Avoid direct skin contact with the liquid.
z Wear gloves when you handle a broken or leaking unit.
z Do not use sharp objects or tools in the vicinity of the LCD touch panel.
z Handle the LCD panel carefully to prevent puncture, bursting, or cracking of the panel material.

Failure to follow these instructions can result in injury or equipment damage.

If the panel is damaged and any liquid comes in contact with your skin, immediately rinse the area with
running water for at least 15 minutes. If the liquid gets in your eyes, immediately rinse your eyes with
running water for at least 15 minutes and consult a doctor.

EIO0000001133 02/2012 13
Overview

14 EIO0000001133 02/2012
 Magelis GTO
Connectivity
EIO0000001133 02/2012

Device Connectivity

2
Introduction
This chapter presents the equipment you can connect to the panel.

Whats in this Chapter?

This chapter contains the following topics:
Topic Page
System Design 16
Accessories 21

EIO0000001133 02/2012 15
Connectivity

System Design

Introduction
The following diagrams represent equipment you can connect to the panel.

COM1 COM2
HMIGTO1300 RS-232C (see page 17) RS-485 (see page 19)
HMIGTO1310 RS-232C / RS-485
(see page 18)
HMIGTO2300 RS-232C (see page 17) RS-485 (see page 19)
HMIGTO2310 RS-232C (see page 17) RS-485 (see page 19)
HMIGTO2315 RS-232C (see page 17) RS-485 (see page 19)
HMIGTO3510 RS-232C (see page 17) RS-485 (see page 19)
HMIGTO4310 RS-232C (see page 17) RS-485 (see page 19)
HMIGTO5310 RS-232C (see page 17) RS-485 (see page 19)
HMIGTO5315 RS-232C (see page 17) RS-485 (see page 19)
HMIGTO6310 RS-232C (see page 17) RS-485 (see page 19)
HMIGTO6315 RS-232C (see page 17) RS-485 (see page 19)

16 EIO0000001133 02/2012
 Connectivity

RUN Mode Peripherals - RS-232C

Serial Interface (RS-232C mode)

RS-232C Port
RS-232C Cable
XBT ZG9731 RS-232C Port
Mitsubishi PLC Q-Series Link Cable
XBT ZG9772 RS-232C Port
Omron PLC SYSMAC Link Cable
XBT ZG9740 RS-232C Port
Mitsubishi PLC Q-Series Connection Cable
XBT ZG9774 Host Controller
RS-232C Port PLC etc.
Premium, Micro, Twido Cable
TSXPCX1031
RS-232C Port
Modicon, Quantum Cable
990NAA26320
RS-232C Port
Advantys STB Cable
STBXCA4002 RS-232C Port
Cable-Gateway for
Siemens Profibus / MPI
(XBT ZG9292)*3
RS-232C Cable
(Prepared by user)
RS-232C Port

9-pin-to-25-pin RS-232C Cable

RS-232C Conversion Cable XBT Z9711/XBT Z9710/XBT Z988
XBT ZG919 XBT Z9740/XBT Z9731/XBT Z9730/XBT Z9720
Serial Interface (RS-232C mode)
RS-232C Port
RS-232C Cable
RS-232C XBTZG9731 RS-232C Port
Isolation Unit
XBTZGI232*1 Mitsubishi PLC Q-Series Link Cable
Switch setting:RS-232C XBTZG9772 RS-232C Port
Omron PLC SYSMAC Link Cable
XBTZG9740 RS-232C Port
Mitsubishi PLC Q-Series Connection Cable
XBTZG9774 Host Controller
RS-232C Port
PLC etc.
Premium, Micro, Twido Cable
TSXPCX1031
RS-232C Port
Modicon, Quantum Cable
990NAA26320
RS-232C Port
Advantys STB Cable
STBXCA4002
Serial Interface (RS-422/485 mode)
RS-422 Port
RS-422 Cable
XBTZG9722
RS-232C Programming
Isolation Unit Mitsubishi PLC Console Port
XBTZGI232*1,2 FX-Series Connection Cable
Switch setting: XBTZG9775
RS-422/485 Programming
Mitsubishi PLC
Console Port
A-Series Connection Cable
XBTZG9773
Host Controller
RS-422 Port PLC etc.

COM Port
Conversion Terminal Block RS-422 Cable
Adapter Conversion Adapter (Prepared by user)
XBTZGCOM1 XBTZG949
Programming
Console Port

2 Port Mitsubishi PLC A, QnA,

Adapter Cable FX Series 2 Port Adapter II
XBTZG9778 XBTZG979

*1 When connecting the XBTZGI232, the COM ports pin 9 setting should be VCC. You can define COM

port settings in Vijeo Designer version 6.1.0 or later or in the Magelis GTOs offline menu.
*2
The RS-232C Isolation Unit does not work with RS-422/485 (2 wire) communication.
*3
Cable-Gateway for Siemens Profibus / MPI (XBT ZG9292) is not supported by HMIGTO1310.

EIO0000001133 02/2012 17
Connectivity

RUN Mode Peripherals - RS-232C / RS-485

Serial Interface (RS-232C mode) RS-232C Port

Omron PLC SYSMAC Link Cable
XBT Z9743

RS-232C Port
DF1-full Duplex D-Sub Cable
XBT Z9733

RS-232C Port
DF1-full Duplex D-Sub Cable
XBT Z9734

RS-232C Port
Advantys STB Cable
XBT Z9715
Host Controller
Serial Interface (RS-232C mode) RS-232C Port PLC etc.
Omron PLC SYSMAC Link Cable
XBT Z9740

RJ45 to D-Sub 25-pin RS-232C Port

DF1-full Duplex D-Sub Cable
Conversion Cable XBT Z9730
XBT ZG939
RS-232C Port
DF1-full Duplex mini-DIN Cable
XBT Z9731

RS-232C Port
Modicon, Quantum Cable
XBT Z9710

RS-232C Port
Modicon, Momentum M1 Cable
XBT Z9711
RS-232C Port
Advantys STB Cable
XBT Z988

RS-232C Port
RS-232C Cable
(Prepared by user)
Serial Interface (RS-485 mode)
RS-485 Port
Twisted Pair Cable
(commercial type) RS-485 Port
PLC Twido Connection Cable
XBT Z9780 / XBT Z9782 RS-485 Port
Derivation Box Connection Cable
VW3A8306 RS-485 Port
Derivation Connection Cable
VW3A8306TF10 Host Controller
RS-485 Port PLC etc.
Modicon M340 Connection Cable
XBT Z9980 / XBT Z9982
RS-485 Port
Siemens PLC Connection Cable
XBT ZG9721
RS-485 Port

RJ45 to D-Sub 25-pin Mitsubishi PLC

Conversion Cable FX-Series Connection Cable
XBT ZG939 XBT Z980

Serial Interface (RS-485 mode)

Connector for Profibus*3 RS-485 Port
(commercial type)
RS-485
Host Controller
Isolation Unit
RS-485 Port PLC etc.
XBT ZGI485*1
Switch setting:
RS-485
Online Adapter*2 Terminal Block
XBT ZGCOM2 Conversion Adapter
XBT ZG949

*1 Use the RS-485 Isolation Units USB port to supply power to itself. There is no need to set up a separate

power supply.
*2
In 1:n, n:1, or n:m communication, you can use the online adapter as a terminal. (Use 1 unit in either
communication setup.)
*3
The connector has a switch to control the terminal. Turn on the switch to enable communication.

18 EIO0000001133 02/2012
 Connectivity

RUN Mode Peripherals - RS-485

Serial Interface (RS-485 mode)

RS-485 Port
Twisted Pair Cable
(commercial type) RS-485 Port
PLC Twido Connection Cable
XBT Z9780 / XBT Z9782 RS-485 Port
Derivation Box Connection Cable
VW3A8306 RS-485 Port
Derivation Connection Cable
VW3A8306TF10 Host Controller
RS-485 Port PLC etc.
Modicon M340 Connection Cable
XBT Z9980 / XBT Z9982
RS-485 Port
Siemens PLC Connection Cable
XBT ZG9721
RS-485 Port

RJ45 to D-Sub 25-pin Mitsubishi PLC

Conversion Cable FX-Series Connection Cable
XBT ZG939 XBT Z980

Serial Interface (RS-485 mode)

Connector for Profibus*3 RS-485 Port
(commercial type)
RS-485
Host Controller
Isolation Unit
RS-485 Port PLC etc.
XBT ZGI485*1
Switch setting:
RS-485
Online Adapter*2 Terminal Block
XBT ZGCOM2 Conversion Adapter
XBT ZG949

*1 Use the RS-485 Isolation Units USB port to supply power to itself. There is no need to set up a separate

power supply.
*2
In 1:n, n:1, or n:m communication, you can use the online adapter as a terminal. (Use 1 unit in either
communication setup.)
*3 The connector has a switch to control the terminal. Turn on the switch to enable communication.

RUN Mode Peripherals - Ethernet Communication

To an Ethernet Network

Ethernet Interface
(10BASE-T/100BASE-TX)

Twisted Pair Cable Hub

(commercial type) (commercial type)

EIO0000001133 02/2012 19
Connectivity

RUN Mode Peripherals - USB Type A / mini-B Interface

USB (Type A) Interface

Bar-Code Reader
(Commercial type)

USB-Serial (RS-232C)
Conversion Cable
HMI ZURS

USB-to-IEEE1284 Printer
Conversion Cable (Commercial type)
(Commercial type)

USB Cable (USB A / mini-B)

(Commercial type)

USB Panel-mount
Extension Cable
(USB Type A)
XBT ZGUSB

USB HUB
(Commercial type)

USB (mini-B) Interface

USB Panel-mount
Extension Cable
(USB mini-B)
HMI ZSUSBB

Edit Mode Peripherals

To an Ethernet Network

Ethernet Interface
(10BASE-T/100BASE-TX)

USB (Type A) Interface USB Port

USB Link Cable

XBT ZG935
Personal Computer Vijeo Designer
USB (mini B) Interface USB Port (Commercial type)

USB Data Transfer Cable

(USB mini-B / Type A)
BMXXCAUSBH018
BMXXCAUSBH045
SD Card Interface USB Port
SD Card Reader
(Commercial type)

SD Memory Card (4GB)

HMI ZSD4G
or Commercial type

SD Card Slot

SD Memory Card (4GB)

HMI ZSD4G
or Commercial type

20 EIO0000001133 02/2012
 Connectivity

Accessories

Serial Interface Items

Product Name Product Number Description

RS-232C Cable XBT ZG9731 Connects a host controller to the panel. (RS-232C)
RS-422 Cable XBT ZG9722 Connects a host controller to the panel. (RS-422)
Mitsubishi PLC Q-Series Link XBT ZG9772 Connects Mitsubishi PLC Q-Series (or other host
Cable controller) to the panel. (RS-232C)
Omron PLC SYSMAC Link Cable XBT ZG9740 Connects Omron PLC SYSMAC Series unit (or other
XBT Z9743 host controller) to the panel. (RS-232C)
XBT Z9740
Mitsubishi PLC A-Series XBT ZG9773 Connects Mitsubishi PLC A or QnA Series
Connection Cable programming console I/F to panel. (Simultaneous
use of programming consoles is not possible.)
Mitsubishi PLC Q-Series XBT ZG9774 Connects Mitsubishi PLC Q-Series programming
Connection Cable console I/F to panel. (Simultaneous use of
programming consoles is not possible.)
Mitsubishi PLC FX-Series XBT ZG9775 Connects Mitsubishi PLC FX-Series programming
Connection Cable XBT Z980 console I/F and panel. (Simultaneous use of
programming consoles is not possible.)
Premium, Micro, Twido Cable TSXPCX1031 Connects Premium, Micro, or Twido to the panel.
Modicon, Quantum Cable 990NAA26320 Connects Modicon or Quantum to the panel.
XBT Z9710
2 Port Adapter Cable XBT ZG9778 Connects Mitsubishi PLC directly to the panel (D-sub
9 pin plug) using 2 port adapter II (RS-422).
Mitsubishi PLC A, QnA, FX Series XBT ZG979 Enables simultaneous use of a panel and a
2 Port Adapter II Mitsubishi PLC A, QnA, or FX Series peripheral
device.
Advantys STB Cable STBXCA4002 Connects Advantys STB to panel.
XBT Z9715
XBT Z988
Terminal Block Conversion XBT ZG949 Connects output from a panels Serial Interface (D-
Adapter sub 9 pin plug) directly with an RS-422 terminal
block.
COM Port Conversion Adapter XBT ZGCOM1 Connects optional RS-422 communication items to
panels COM1 port.
DF1-full Duplex D-Sub Cable XBT Z9730 Connects DF1-full Duplex to Magelis GTO.
XBT Z9733
XBT Z9734
DF1-full Duplex mini-DIN Cable XBT Z9731 Connects DF1-full Duplex to Magelis GTO.
XBT Z9720
Modicon, Momentum M1 Cable XBT Z9711 Connects Modicon, Momentum M1 to Magelis GTO.
PLC Twido Connection Cable XBT Z9780 / XBT Z9782 Connects PLC Twido to Magelis GTO.
Derivation Box Connection Cable VW3A8306 Connects Derivation Box to Magelis GTO.
Derivation Connection Cable VW3A8306TF10 Connects Derivation to Magelis GTO.
Modicon M340 Connection Cable XBT Z9980 / XBT Z9982 Connects Modicon M340 to Magelis GTO.
Siemens PLC Connection Cable XBT ZG9721 Connects Siemens PLC to Magelis GTO.
RS-232C Isolation Unit XBT ZGI232 Connects a host controller to Magelis GTO with
isolation. (RS-232C and RS-422 are switchable.)
RS-485 Isolation Unit XBT ZGI485 Connects a host controller to Magelis GTO with
isolation.
Cable-gateway for Siemens XBT ZG9292 Connects Siemens Profibus / MPI units to Magelis
Profibus / MPI GTO.
RJ45 to D-Sub 25 pin Conversion XBT ZG939 Connects a RJ45 cable to Magelis GTO (D-sub 9 pin
Cable plug).
9-pin to 25-pin RS-232C XBT ZG919 Connects a standard RS-232C cable (D-Sub 25-pin
Conversion Cable socket) to Magelis GTO (D-sub 9 pin plug).
Online Adapter XBT ZGCOM2 Terminal adapter for RS-485 communication.

EIO0000001133 02/2012 21
Connectivity

USB Interface Items

Product Name Product Number Description

USB Transfer Cable XBT ZG935 Downloads project data created with the
software via the panels USB I/F.
USB Front Cable XBT ZGUSB Extension cable attaching USB interface to
front panel.
USB-Serial (RS-232C) HMIZURS Cable for converting a panels USB interface
Conversion Cable into a serial interface (RS-232C).
Allows connection to modems*1 or bar code
readers*1 that support RS-232C.
USB Transfer Cable (USB Type BMXXCAUSBH018 Cable for transferring screen data from a PC
A/mini-B) BMXXCAUSBH045 (USB Type A) to the panel (USB mini-B).
Remote USB port location for HMIZSUSBB Extension cable that attaches to the USB
mini-USB XBT ZGUSBB (mini-B) interface on the front side of the
operation panel.

Software

Product name Description

Vijeo Designer Software you install on your computer to create project
(Version 6.1 or later) data for your Magelis GTO.

SD Card Items

Product Name Product Number Description

SD Memory Card (4 GB) HMIZSD4G SD Memory Card (4 GB, CLASS4)

Option Items

Product Name Product Number Corresponding panel Description

12.1-inch Screen Protection Sheet XBT ZG66 HMIGTO6310/6315 Disposable, dirt-resistant sheet for the
Magelis GTO screen (5 sheets/set)
10.4-inch Screen Protection Sheet XBT ZG65 HMIGTO5310/5315
7.5-inch Screen Protection Sheet XBT ZG64 HMIGTO4310
7.0-inch Wide Screen Protection Sheet XBT ZG63 HMIGTO3510
5.7-inch Screen Protection Sheet XBT ZG62 HMIGTO2300/2310/2315
3.5-inch Screen Protection Sheet XBT ZG60 HMIGTO1300/1310
12.1-inch Environment Cover XBT ZECOV6 HMIGTO6310 Disposable, environment cover for the
Magelis GTO screen (1 sheet/set)
10.4-inch Environment Cover XBT ZECOV5 HMIGTO5310
7.0/7.5-inch Environment Cover XBT ZECOV4 HMIGTO3510/4310
5.7-inch Environment Cover XBT ZECOV2 HMIGTO2300/2310
3.5-inch Environment Cover XBT ZECOV1 HMIGTO1300/1310

Maintenance Options

Product Name Product Number Corresponding panel Description

Installation Fastener HMI ZGFIX Magelis GTO except Used to install the Magelis GTO into a
HMIGTO2315/5315/6315 solid panel (4 pieces/set)
Installation System HMI ZGFIX2 HMIGTO2315/5315/6315 Used to install the Magelis GTO into a
solid panel.
Brackets (4 pieces/set)
M4 Hex nuts (8 pieces/set)

22 EIO0000001133 02/2012
 Connectivity

Product Name Product Number Corresponding panel Description

12.1-inch Installation Gasket HMI ZG56 HMIGTO6310 Provides dust and moisture resistance
when Magelis GTO is installed into a
HMI ZG562 HMIGTO6315
solid panel (1 piece)
10.4-inch Installation Gasket HMI ZG55 HMIGTO5310
HMI ZG552 HMIGTO5315
7.0-inch Wide & 7.5-inch Installation HMI ZG54 HMIGTO3510/4310
Gasket
5.7-inch Installation Gasket HMI ZG52 HMIGTO2300/2310
HMI ZG522 HMIGTO2315
3.5-inch Installation Gasket HMI ZG51 HMIGTO1300/1310
USB Clamp TypeA (1 port) HMI ZGCLP1 Magelis GTO Clamp to prevent disconnection of USB
cable (USB/A, 1 port, 5 clamps/set)
USB Clamp mini-B (1 port) HMI ZGCLP3 Magelis GTO Clamp to prevent disconnection of USB
cable (USB/mini-B, 1 port, 5 clamps/set)
DC Power Supply Connector HMI ZGPWS HMIGTO3510/4310 Connector to connect DC power supply
HMIGTO2300/2310/2315 cables (5 pcs/set)
HMIGTO1300/1310
DC Power Supply Connector (Right-angle) HMI ZGPWS2 HMIGTO6310/6315 Right-angle connector to connect DC
HMIGTO5310/5315 power supply cables (5 pcs/set)
Battery for Memory Backup HMI ZGBAT Magelis GTO (except Primary battery for memory and time
HMIGTO1300/1310/2300) data backup
Panel Cutout Adapter XBT ZGGCO4 HMIGTO5310 Panel cutout adapter for mounting
HMIGTO5310 in cutout for XBT
GT5230.
Insert Label HMI ZLYGO3 HMIGTO3510 Label insert for Magelis GTO 7-inch
Wide models.
HMI ZLYGO1 HMIGTO1300/1310 Label insert for Magelis GTO 3.5-inch
models

EIO0000001133 02/2012 23
Connectivity

24 EIO0000001133 02/2012
 Magelis GTO
Parts/Functions
EIO0000001133 02/2012

Parts Identification and Functions

3
Parts Identification and Functions

HMIGTO1300/1310 Parts Identification

Side HMIGTO1300/1310
Front

A B

Rear

D
C

Bottom
G H E

HMIGTO1300

G F E

HMIGTO1310

Part Name Description

A Status LED *1

B Function Switches Six switches (F1 to F6). You can define

operations for these switches using Vijeo
Designer.
C USB (mini-B) Interface Conforms to USB2.0 (mini-B) x 1.
Communication Distance: 5 m (16.4 ft) or
less.

EIO0000001133 02/2012 25
Parts/Functions

Part Name Description

D USB (Type A) Interface Conforms to USB2.0 (Type A) x 1.
Power supply voltage: 5Vdc+/-5%.
Output Current: 500 mA or less.
Maximum communication distance: 5 m
(16.4 ft).
E Serial Interface (COM1) HMIGTO1300: RS-232C Serial Interface.
Connector: D-Sub 9 pin (plug) x 1.
HMIGTO1310: RS-232C/485 Serial
Interface. (You can switch the
communication method via software.)
Connector: Modular jack (RJ-45).
F Ethernet Interface*2 Ethernet transmission interface: 10BASE-T/
100BASE-TX.
Connector: Modular jack (RJ-45) x 1.
Ethernet Interface is not available on
HMIGTO1300.
G Power Plug Connector -
H Serial Interface (COM2) HMIGTO1300: RS-485 Serial Interface.
Connector: Modular jack (RJ-45) x 1.

*1
Status LED operations are as shown below:

Color Indicator Description

Green ON Offline
In operation
Orange Flashing Software starting up
Red ON Power is turned ON.
- OFF Power is turned OFF.

*2 Ethernet LED operations are as shown below.

Color Indicator Description

Green (Active) Flashing Data transmission is occurring.
OFF No data transmission.
Link
Green (Link) ON Data transmission is available in
10BASE-T/100BASE-TX.
Active OFF No connection or subsequent
loss of communication.

26 EIO0000001133 02/2012
 Parts/Functions

HMIGTO2300/2310/2315 Parts Identification

Side HMIGTO2300/HMIGTO2310 HMIGTO2315

Front

A B
A

Right

C
C
D
D

E E

Rear

F G
F G

Bottom

F I
F H I J

HMIGTO2300
F H I J

HMIGTO2310

Part Name Description

A Status LED *1

B Stainless Steel Bezel HMIGTO2315 only.

EIO0000001133 02/2012 27
Parts/Functions

Part Name Description

C USB (Type A) Interface Conforms to USB2.0 (Type A) x 1.
Power supply voltage: 5Vdc+/-5%.
Output Current: 500 mA or less.
Maximum communication distance: 5 m (16.4 ft).
D Serial Interface (COM1) RS-232C Serial Interface. Connector: D-Sub 9
pin (plug) x 1.
E Serial Interface (COM2)*2 RS-485 Serial Interface. Connector: Modular jack
(RJ-45).
F Power Plug Connector -
G SD Card Access LED *3 This lamp lights up when SD Card is inserted.
For more information, refer to SD Card
Insertion/Removal (see page 124).
NOTE: SD Card Access LED is not available on
HMIGTO2300.
H SD Card Interface For information on how to open the cover, and
Cover/Replacement Battery insert or remove the SD Card, refer to SD Card
Insertion Cover Insertion / Removal (see page 124).
For information on how to open the cover and
replace the battery, refer to Replacing the
Primary Battery (see page 138).
NOTE: This cover is not on HMIGTO2300.
I USB (mini-B) Interface Conforms to USB2.0 (mini-B) x 1.
Communication Distance: 5 m (16.4 ft) or less.
J Ethernet Interface *4 Ethernet transmission interface: 10BASE-T/
100BASE-TX.
Connector: Modular jack (RJ-45) x 1.
NOTE: Ethernet Interface is not available on
HMIGTO2300.

*1
Status LED operations are as shown below:

Color Indicator Description

Green ON Offline
In operation
Orange Flashing Software starting up
Red ON Power is turned ON.
- OFF Power is turned OFF.

*2 COM2 LED operations are as shown below.

Color Indicator Description

Yellow ON Communication (sending or receiving data) is
occurring.
OFF No communication.

*3
SD Card Access LED operations are as shown below.

Color Indicator Description

Green (Active) ON The SD Card is inserted.
OFF The SD Card is not inserted or is not
being accessed.

*4 Ethernet LED operations are as shown below.

Color Indicator Description

Green (Active) Flashing Data transmission is occurring.
OFF No data transmission.
Link
Green (Link) ON Data transmission is available in
10BASE-T/100BASE-TX.
Active OFF No connection or subsequent
loss of communication.

28 EIO0000001133 02/2012
 Parts/Functions

HMIGTO3510/4310 Parts Identification

Side HMIGTO3510/4310
Front
HMIGTO3510

A B

HMIGTO4310

Right

Rear

F G

Bottom
F H I J

Part Name Description

A Status LED *1

B Function Switches HMIGTO3510 only. Eight switches (F1 to F8).

You can define operations for these switches
using Vijeo Designer.

EIO0000001133 02/2012 29
Parts/Functions

Part Name Description

C USB (Type A) Interface Conforms to USB2.0 (Type A) x 1.
Power supply voltage: Vdc5+/-5%.
Output Current: 500 mA or less.
Maximum communication distance: 5 m (16.4 ft).
D Serial Interface (COM1) RS-232C Serial Interface. Connector: D-Sub 9 pin
(plug) x 1.
E Serial Interface (COM2)*2 RS-485 Serial Interface. Connector: Modular jack
(RJ-45) x 1.
F Power Plug Connector -
G SD Card Access LED *3 This lamp lights up when SD Card is inserted.
For more information, refer to SD Card Insertion /
Removal (see page 124).
H SD Card Interface For information on how to open the cover, and
Cover/Replacement Battery insert or remove the SD Card, refer to SD Card
Insertion Cover Insertion / Removal (see page 124).
For information on how to open the cover and
replace the battery, refer to Replacing the Primary
Battery (see page 138).
I USB (mini-B) Interface Conforms to USB2.0 (mini-B) x 1. Communication
Distance: 5 m (16 ft) or less.
J Ethernet Interface *4 Ethernet transmission interface: 10BASE-T/
100BASE-TX.
Connector: Modular jack (RJ-45) x 1.

*1
Status LED operations are as shown below:

Color Indicator Description

Green ON Offline
In operation
Orange Flashing Software starting up
Red ON Power is turned ON.
- OFF Power is turned OFF.

*2 COM2 LED operations are as shown below.

Color Indicator Description

Yellow ON Communication (sending or receiving data) is
occurring.
OFF No communication.

*3
SD Card Access LED operations are as shown below.

Color Indicator Description

Green (Active) ON The SD Card is inserted.
OFF The SD Card is not inserted or is not
being accessed.

*4 Ethernet LED operations are as shown below.

Color Indicator Description

Green (Active) Flashing Data transmission is occurring.

Link OFF No data transmission.

Green (Link) ON Data transmission is available in
10BASE-T/100BASE-TX.
Active OFF No connection or subsequent
loss of communication.

30 EIO0000001133 02/2012
 Parts/Functions

HMIGTO5310/5315 Parts Identification

Side HMIGTO5310 HMIGTO5315

Front

A
A B

Rear

C D
C D

Bottom
G J FI H E
G J FI H E

Part Name Description

A Status LED *1

B Stainless Steel Bezel HMIGTO5315 only.

C Power Plug Connector -
D SD Card Access LED *2 This lamp lights up when SD Card is inserted.
For more information, refer to SD Card Insertion
/ Removal (see page 124).
E Ethernet Interface *3 Ethernet transmission interface: 10BASE-T/
100BASE-TX.
Connector: Modular jack (RJ-45) x 1.
F USB (mini-B) Interface Conforms to USB2.0 (mini-B) x 1.
Communication Distance: 5 m (16 ft) or less.
G SD Card Interface For information on how to open the cover, and
Cover/Replacement Battery insert or remove the SD Card, refer to SD Card
Insertion Cover Insertion/Removal (see page 124).
For information on how to open the cover and
replace the battery, refer to Replacing the
Primary Battery (see page 138).
H Serial Interface (COM2)*4 RS-485 Serial Interface.
Connector: Modular jack (RJ-45).
I Serial Interface (COM1) RS-232C Serial Interface.
Connector: D-Sub 9 pin (plug) x 1.
J USB (Type A) Interface Conforms to USB2.0 (Type A) x 1.
Power supply voltage: Vdc5+/-5%.
Output Current: 500 mA or less.
Maximum communication distance: 5 m (16 ft).

EIO0000001133 02/2012 31
Parts/Functions

*1
Status LED operations are as shown below:

Color Indicator Description

Green ON Offline
In operation
Orange Flashing Software starting up
Red ON Power is turned ON.
- OFF Power is turned OFF.

*2
SD Card Access LED operations are as shown below.

Color Indicator Description

Green (Active) ON The SD Card is inserted.
OFF The SD Card is not inserted or is not
being accessed.

*3 Ethernet LED operations are as shown below.

Color Indicator Description

Green (Active) Flashing Data transmission is occurring.
OFF No data transmission.
Link
Green (Link) ON Data transmission is available in
10BASE-T/100BASE-TX.
Active OFF No connection or subsequent
loss of communication.

*4
COM2 LED operations are as shown below.

Color Indicator Description

Yellow ON Communication (sending or receiving data) is
occurring.
OFF No communication.

32 EIO0000001133 02/2012
 Parts/Functions

HMIGTO6310/6315 Parts Identification

Side HMIGTO6310 HMIGTO6315

Front

A A B

Rear

C D C D

Bottom
G J IF H E G J IF H E

Part Name Description

A Status LED *1

B Stainless Steel Bezel HMIGTO6315 only.

C Power Plug Connector -
D SD Card Access LED *2 This lamp lights up when SD Card is inserted.
For more information, refer to SD Card
Insertion/Removal (see page 124).
E Ethernet Interface *3 Ethernet transmission interface: 10BASE-T/
100BASE-TX.
Connector: Modular jack (RJ-45) x 1.
F USB (mini-B) Interface Conforms to USB2.0 (mini-B) x 1.
Communication Distance: 5 m (16 ft) or less.
G SD Card Interface For information on how to open the cover, and
Cover/Replacement Battery insert or remove the SD Card, refer to SD Card
Insertion Cover Insertion/Removal (see page 124).
For information on how to open the cover and
replace the battery, refer to Replacing the
Primary Battery (see page 138).
H Serial Interface (COM2) RS-485 Serial Interface. Connector: Modular
jack (RJ-45)
I Serial Interface (COM1) RS-232C Serial Interface. Connector: D-Sub 9
pin (plug) x 1.
J USB (Type A) Interface Conforms to USB2.0 (Type A) x 1.
Power supply voltage: Vdc5+/-5%.
Output Current: 500 mA or less.
Maximum communication distance: 5 m (16 ft).

EIO0000001133 02/2012 33
Parts/Functions

*1
Status LED operations are as shown below:

Color Indicator Description

Green ON Offline
In operation
Orange Flashing Software starting up
Red ON Power is turned ON.
- OFF Power is turned OFF.

*2
SD Card Access LED operations are as shown below.

Color Indicator Description

Green (Active) ON The SD Card is inserted.
OFF The SD Card is not inserted or is not
being accessed.

*3 Ethernet LED operations are as shown below.

Color Indicator Description

Green (Active) Flashing Data transmission is occurring.
OFF No data transmission.
Link
Green (Link) ON Data transmission is available in
10BASE-T/100BASE-TX.
Active OFF No connection or subsequent
loss of communication.

*4
COM2 LED operations are as shown below.

Color Indicator Description

Yellow ON Communication (sending or receiving data) is
occurring.
OFF No communication.

34 EIO0000001133 02/2012
 Magelis GTO
Specifications
EIO0000001133 02/2012

Specifications

4
Overview
This chapter presents the Magelis GTO specifications.

Whats in this Chapter?

This chapter contains the following sections:
Section Topic Page
4.1 HMIGTO1300/1310 36
4.2 HMIGTO2300/2310/2315 50
4.3 HMIGTO3510/4310 66
4.4 HMIGTO5310/5315 80
4.5 HMIGTO6310/6315 95

EIO0000001133 02/2012 35
Specifications

4.1 HMIGTO1300/1310

Whats in this Section?

This section contains the following topics:
Topic Page
Electrical Specifications 37
Environmental Specifications 38
Structural Specifications 39
Display Specifications 40
Memory, Clock, Touch Panel and Function Switches 41
Interface Specifications 42
Specifications of Serial Interface COM1 43
Specifications of Serial Interface COM2 45
Dimensions 46

36 EIO0000001133 02/2012
 Specifications

Electrical Specifications

Rated Input Voltage 24 Vdc

Input Voltage Limits 19.2...28.8 Vdc
Voltage Drop 2 ms or less
Power Supply

Power Consumption 9.6 W or less

When power is not supplied to 5.2 W or less
external devices
Backlight OFF (Standby Mode) 4.2 W or less
Backlight Dimmed (Brightness: 4.3 W or less
20%)
In-Rush Current 30 A or less
Voltage Endurance 1,000 Vac 20 mA for 1 minute
(between charging and FG
terminals)
Insulation Resistance 500 Vdc, 10 M or more
(between charging and FG
terminals)

EIO0000001133 02/2012 37
Specifications

Environmental Specifications

Surrounding Air 0...50 C (32...122 F)

Temperature
Storage Temperature -20...+60 C (-4...140 F)
Physical Environment
Surrounding Air and 10%...90% RH (Non condensing, wet bulb
Storage Humidity temperature 39 C [102.2 F] or less)
Dust 0.1 mg/m3 (10-7 oz./ft3) or less (non-conductive
levels)
Pollution Degree For use in Pollution Degree 2 environment
Corrosive Gases Free of corrosive gases
Atmospheric Pressure 800...1114 hPa (2000 m [6561 ft] or lower)
(Operating Altitude)
Vibration Resistance IEC/EN 61131-2 compliant
Electrical Environment Mechanical Environment

5...9 Hz Single amplitude 3.5 mm (0.14 in.)

9...150 Hz Fixed acceleration: 9.8 m/s2
X, Y, Z directions for 10 cycles (approx. 100 min.)
Concussion Resistance IEC/EN 61131-2 compliant
147 m/s2, X, Y, Z directions for 3 times

Noise immunity Noise Voltage: 1000 Vp-p

Pulse Width: 1 s
Rise Time: 1 ns
(via noise simulator)
Electrostatic Discharge Contact Discharge Method: 6 kV (IEC/EN61000-4-2
Immunity Level 3)

Air quality requirements

Do not operate or store the panel where chemicals evaporate, or where chemicals are present in the air:
z Corrosive chemicals: Acids, alkalines, liquids containing salt.
z Flammable chemicals: Organic solvents.

CAUTION
INOPERATIVE EQUIPMENT
Do not allow water, liquids, metal, and wiring fragments to enter the panel case.
Failure to follow these instructions can result in injury or equipment damage.

38 EIO0000001133 02/2012
 Specifications

Structural Specifications

Grounding Functional grounding: Grounding resistance

of 100, 2mm2 (AWG 14) or thicker wire, or
your countrys applicable standard. (Same
for FG and SG terminals)
Cooling Method Natural air circulation

Structure *1 IP65f NEMA #250 TYPE 4X/13 (on the front

panel when properly installed in an
enclosure)
External Dimensions W132 x H106 x D42 mm (W5.2 x H4.17 x
D1.65 in.)
Panel Cut Dimensions W118.5 x H92.5 mm (W4.67 x H3.64 in.)*2
Panel thickness area: 1.6 mm...5 mm
(0.06...0.2 in)*3
Weight 0.4 kg (0.9 lb) or less (main unit only)

*1 The front face of the Magelis GTO, installed in a solid panel, has been tested using conditions
equivalent to the standards shown in the specification. Even though the Magelis GTOs level of resistance
is equivalent to these standards, oils that should have no effect on the Magelis GTO can possibly harm
the panel. This can occur in areas where either vaporized oils are present, or where low viscosity cutting
oils are allowed to adhere to the panel for long periods of time. If the panels front face protection sheet
peels off, these conditions can lead to the ingress of oil into the panel and separate protection measures
are suggested.
*2
For dimensional tolerance, everything +1/-0 mm (+0.04/-0 in) and R in angle are below R3 (R0.12in).
*3 Even if the installation wall thickness is within the recommended range for the Panel Cut Dimensions,

depending on walls material, size, and installation location of the panel and other devices, the installation
wall could warp. To prevent warping, the installation surface may need to be strengthened.
The front face of the panel, installed in a solid panel, has been tested using conditions equivalent to the
standards shown in the specification.

CAUTION
EQUIPMENT DAMAGE
Ensure that the panel is not in permanent and direct contact with oils.
Failure to follow these instructions can result in injury or equipment damage.

NOTICE
STORAGE AND OPERATION OUTSIDE OF SPECIFICATIONS
z Store the panel in areas where temperatures are within the panels specifications.
z Do not restrict or block the panels rear-face ventilation slots.
Failure to follow these instructions can result in equipment damage.

NOTICE
GASKET AGING
z Inspect the gasket periodically as required by your operating environment to keep the initial IP level.
z Change the gasket at least once a year, or as soon as scratches or dirt become visible.
Failure to follow these instructions can result in equipment damage.

EIO0000001133 02/2012 39
Specifications

Display Specifications

HMIGTO1310 HMIGTO1300
Display Type TFT Color LCD
Display Size 3.5
Resolution 320 x 240 pixels (QVGA)
Effective Display Area W70.56 x H52.92 mm (W2.78 x H2.08 in.)
Display Colors 65,536 colors (No blink) / 16,384 colors (Blink)
Backlight White LED (Not user-replaceable. When
replacement is required, contact your local
distributor.)
Backlight Service Life 50,000 hours or more (continuous operation at 25 C
[77 F] before backlight brightness decreased to
50%)
Brightness Control 16 levels (Adjusted with touch panel or software)
Language Fonts ASCII: (Code page 850) Alphanumeric (including
European characters)
Chinese: (GB2312-80 codes) Simplified Chinese
fonts
Japanese (except for XBT GT1000 series): ANK
158, Kanji: 6,962 (JIS Standards 1 & 2) (including
607 non-kanji characters)
Korean: (KSC5601 - 1992 codes) Hangul fonts
Taiwanese: (Big 5 codes) Traditional Chinese fonts
Character sizes 8 x 8, 8 x 16, 16 x 16 and 32 x 32 pixel fonts
Font sizes You can expand width up to 8 times, and expand
height up to 8 times.*1
Text 8 x 8 pixels 40 characters per row x 30 rows
8 x 16 pixels 40 characters per row x 15 rows
16 x 16 pixels 20 characters per row x 15 rows
32 x 32 pixels 10 characters per row x 7 rows

*1
You can set up other font sizes using the software.

40 EIO0000001133 02/2012
 Specifications

Memory, Clock, Touch Panel and Function Switches

Memory

HMIGTO1310 HMIGTO1300

Application Memory *1 FLASH EPROM 96 MB FLASH EPROM 64 MB

Data Backup SRAM 512 KB SRAM 128 KB

(Rechargeable lithium (Rechargeable lithium
battery for backup battery for backup
memory) memory)

*1
Capacity available for user application.
NOTE:
z When the message Battery level is low is displayed, supply power to the panel and fully charge.
z The rechargeable battery requires 24 hours to charge to a level that allows backup operation.
Completing a full charge requires about 120 hours (5 days).
z The lifetime of the rechargeable lithium battery is 10 years when the batterys ambient temperature is
40 C (104 F) or less, 4.1 years when the batterys ambient temperature is 50 C (122 F) or less, and
1.5 years when the batterys ambient temperature is 60 C (140 F) or less.
When used for backup:
Approximately 100 days with a fully charged battery.
Approximately 6 days with a half-charged battery.

Clock

Clock Accuracy*1 65 seconds/month (deviation at room temperature

and power is OFF).

*1 Depending on the operating temperature and age of panel, the clock can deviate from -380 to +90
sec/month. For systems where this level of precision is insufficient, the user should monitor and make
adjustments when required.

Touch Panel

Touch Panel Type Resistive Film (analog)

Touch Panel Resolution 1,024 x 1,024
Touch Panel Service Life 1 million times or more

Function Switches
Six switches (F1 to F6).

EIO0000001133 02/2012 41
Specifications

Interface Specifications

Serial Interface COM1

HMIGTO1310 HMIGTO1300
Asynchronous RS-232C / RS-485 RS-232C
Transmission
Data Length 7 or 8 bits
Stop Bit 1 or 2 bits
Parity None, odd or even
Data Transmission 2,400...115,200 bps, 187,500 2,400...115,200 bps
Speed bps (MPI)
Connector Modular jack (RJ-45) D-Sub 9 pin (plug)

Serial Interface COM2

HMIGTO1300
Asynchronous Transmission RS-485
Data Length 7 or 8 bits
Stop Bit 1 or 2 bits
Parity None, odd or even
Data Transmission Speed 2,400...115,200 bps,
187,500 bps (MPI)
Connector Modular jack (RJ-45)

USB Interface

USB (Type A) Interface USB (mini-B) Interface

Connector USB 2.0 (Type A) x 1 USB 2.0 (mini-B) x 1
Power Supply Voltage 5 Vdc 5% -
Maximum Current 500 mA -
Supplied
Maximum Transmission 5 m (16.4 ft)
Distance

Ethernet Interface

HMIGTO1310
Ethernet (LAN) IEEE802.3i / IEEE802.3u,
10BASE-T/100BASE-TX
Connector Modular jack (RJ45) x 1

NOTE: HMIGTO1300 does not have an Ethernet interface.

42 EIO0000001133 02/2012
 Specifications

Specifications of Serial Interface COM1

Introduction
The serial port is not isolated. The SG (signal ground) and FG (frame ground) terminals are connected
inside the panel.

DANGER
ELECTRIC SHOCK
When using the SG terminal to connect an external device to the panel:
z Verify that a short-circuit loop is not created when you set up the system.
z For HMIGTO1300, connect the #5 SG terminal to remote equipment when the host (PLC) unit is not
isolated. Connect the #5 SG terminal to a known reliable ground connection to reduce the risk of
damaging the circuit.
z For HMIGTO1310, connect the #8 SG terminal to remote equipment when the host (PLC) unit is not
isolated. Connect the #8 SG terminal to a known reliable ground connection to reduce the risk of
damaging the circuit.
Failure to follow these instructions will result in death or serious injury.

Serial Interface COM1

HMIGTO1300: D-Sub 9 pin plug connector via an RS-232C cable.

Pin Connection Pin RS-232C

No. Signal Name Direction Meaning
1 CD Input Carrier Detect
2 RD(RXD) Input Receive Data
3 SD(TXD) Output Send Data
4 ER(DTR) Output Data Terminal Ready
5 SG - Signal Ground
6 DR(DSR) Input Data Set Ready
7 RS(RTS) Output Request to Send
8 CS(CTS) Input Send possible
9 CI(RI)/VCC Input/ Called Status Display
+5V5% Output 0.25A
Shell FG Frame Ground (Common
with SG)

You can switch pin #9 between RI and VCC via software.

NOTICE
EQUIPMENT DAMAGE
Use only the rated current.
Failure to follow these instructions can result in equipment damage.

Interfit bracket is #4-40 (UNC).

CAUTION
LOSS OF COMMUNICATION
z Do not put excessive stress on the communication ports.
z Securely attach communication cables to the panel wall or cabinet.
z Use only D-Sub 9 pin cables with a locking tab in good condition.
Failure to follow these instructions can result in injury or equipment damage.

EIO0000001133 02/2012 43
Specifications

HMIGTO1310: RJ-45 connector via an RS-232C or RS-485 cable.

Pin Connection Pin RS-232C/RS-485

No. Signal Name Direction Meaning
1 RD(RXD) Input Receive Data (RS-232C)
Front
2 SD(TXD) Output Send Data (RS-232C)
3 NC
4 D1 Input/Output Transfer Data (RS-485)
5 D0 Input/Output Transfer Data (RS-485)
6 RS(RTS) Output Request to Send
7 NC
8 SG Signal Ground
Shell FG Frame Ground (Common
with SG)

CAUTION
LOSS OF COMMUNICATION
z Do not put excessive stress on the communication ports.
z Securely attach communication cables to the panel wall or cabinet.
z Use only RJ45 with a locking tab in good condition.
Failure to follow these instructions can result in injury or equipment damage.

44 EIO0000001133 02/2012
 Specifications

Specifications of Serial Interface COM2

Introduction
The serial port is not isolated. The SG (signal ground) and FG (frame ground) terminals are connected
inside the panel.

DANGER
ELECTRIC SHOCK
When using the SG terminal to connect an external device to the panel:
z Verify that a short-circuit loop is not created when you set up the system.
z Connect the #8 SG terminal to remote equipment when the host (PLC) unit is not isolated. Connect
the #8 SG terminal to a known reliable ground connection to reduce the risk of damaging the circuit.
Failure to follow these instructions will result in death or serious injury.

Serial Interface COM2

HMIGTO1300: RJ-45 connector via an RS-485 cable
NOTE: When setting up RS-485 communication, the cable diagram for some equipment may require
polarization on the terminal side. This terminal does not require any special setting as it handles
polarization automatically.

Pin Connection Pin RS-485

No. Signal Name Direction Meaning
1 NC
Front
2 NC
3 NC
4 Line A Input/Output Transfer Data (RS-485)
5 Line B Input/Output Transfer Data (RS-485)
6 RS(RTS) Output Request to Send
7 NC
8 SG Signal Ground

CAUTION
LOSS OF COMMUNICATION
z Do not put excessive stress on the communication ports.
z Securely attach communication cables to the panel wall or cabinet.
z Use only RJ45 with a locking tab in good condition.
Failure to follow these instructions can result in injury or equipment damage.

EIO0000001133 02/2012 45
Specifications

Dimensions

External Dimensions

mm (3)
in.

118
4.65

132 42
5.20
9 5 1.65
0.35 0.20

3.62
92
4.17
106

DISPLAY AREA CENTER PRODUCT CENTER

(1) (2)

1 Front
2 Right Side
3 Top

Installation with Installation Fasteners

mm (4)
in.
142
5.59

118
4.65

132 42
5.20 1.65
9 5
0.35 0.20
3.62
1.69

4.17

1.69
106

92
43

43

DISPLAY AREA CENTER PRODUCT CENTER

(1) (2) (3)

(5)

1 Left Side
2 Front
3 Right Side
4 Top
5 Bottom

46 EIO0000001133 02/2012
 Specifications

Dimensions with Cables: HMIGTO1300

(4)
mm
in.

73
2.87
59
2.32

0.83
21
1.42
36

3.70
(1) (2) (3)

94

(5)

1 Left Side
2 Rear
3 Right Side
4 Top
5 Bottom
NOTE: All the above values are designed with cable bending in mind. The dimensions given here are
representative values depending on the type of connection cable in use. Therefore, these values are
intended for reference only.

EIO0000001133 02/2012 47
Specifications

Dimensions with Cables: HMIGTO1310

(4)
mm
in.

73
2.87
59
2.32

0.55
14
1.14
29

(1) (2) (3)

(5)

1 Left Side
2 Rear
3 Right Side
4 Top
5 Bottom
NOTE: All the above values are designed with cable bending in mind. The dimensions given here are
representative values depending on the type of connection cable in use. Therefore, these values are
intended for reference only.

Panel Cut Dimensions

Create a panel cut and insert the panel into the opening from the front.

A
R C
B

A B C R
118.5 mm (+1, -0 mm) 92.5 mm (+1, -0 mm) 1.6...5 mm (0.06...0.2 in.) 3 mm (0.12 in.)
(4.67 in [+0.04, -0 in.]) (3.64 in. [+0.04, -0 in.]) maximum

NOTE: Before designing the panel cut, refer to Installation (see page 112).

48 EIO0000001133 02/2012
 Specifications

Installation Fastener Dimensions

mm
in. 14
0
1 .39 M6 0.55
0

0.47
12
12
0.47

26
1.02

EIO0000001133 02/2012 49
Specifications

4.2 HMIGTO2300/2310/2315

Whats in this Section?

This section contains the following topics:
Topic Page
Electrical Specifications 51
Environmental Specifications 52
Structural Specifications 53
Display Specifications 55
Memory, Clock, and Touch Panel 56
Interface Specifications 57
Specifications of Serial Interface COM1 58
Specifications of Serial Interface COM2 59
Dimensions 60

50 EIO0000001133 02/2012
 Specifications

Electrical Specifications

Rated Input Voltage 24 Vdc

Input Voltage Limits 19.2...28.8 Vdc
Voltage Drop 5 ms or less
Power Supply

Power Consumption 10.5 W or less

When power is not supplied to 6.5 W or less
external devices
Backlight OFF (Standby Mode) 4.5 W or less
Backlight Dimmed (Brightness: 5 W or less
20%)
In-Rush Current 30 A or less
Voltage Endurance 1000 Vac, 20 mA for 1 minute
(between charging and FG
terminals)
Insulation Resistance 500 Vdc, 10 M or more
(between charging and FG
terminals)

EIO0000001133 02/2012 51
Specifications

Environmental Specifications

HMIGTO2310 / HMIGTO2300
HMIGTO2315
Surrounding air 0...55 C (32 F...131 F) 0...50 C (32...122 F)
temperature
Storage temperature -20...60 C (-4...140 F)
Physical Environment

Surrounding Air and 10...90% RH (Non condensing, wet bulb temperature 39 C

Storage Humidity [102.2 F] or less)
Dust 0.1 mg/m3 (10-7 oz./ft3) or less (non-conductive levels)
Pollution Degree For use in Pollution Degree 2 environment
Corrosive Gases Free of corrosive gases
Atmospheric Pressure 800...1,114 hPa (2,000 m [6,561 ft] or lower)
(Operating Altitude)
Vibration Resistance IEC/EN 61131-2 compliant
Electrical Environment Mechanical Environment

5...9 Hz Single amplitude 3.5 mm (0.14 in.)

9...150 Hz Fixed acceleration: 9.8 m/s2
X, Y, Z directions for 10 cycles (approx. 100 min.)
Concussion Resistance IEC/EN 61131-2 compliant
147 m/s2, X, Y, Z directions for 3 times

Noise immunity Noise Voltage: 1000 Vp-p

Pulse Width: 1 s
Rise Time: 1 ns
Electrostatic Discharge Contact Discharge Method: 6 kV (IEC/EN61000-4-2 Level 3)
Immunity

Air quality requirements

Do not operate or store the panel where chemicals evaporate, or where chemicals are present in the air:
z Corrosive chemicals: Acids, alkalines, liquids containing salt.
z Flammable chemicals: Organic solvents.

CAUTION
INOPERATIVE EQUIPMENT
Do not allow water, liquids, metal, and wiring fragments to enter the panel case.
Failure to follow these instructions can result in injury or equipment damage.

52 EIO0000001133 02/2012
 Specifications

Structural Specifications

HMIGTO2300/HMIGTO2310 HMIGTO2315
Grounding Functional grounding: Grounding resistance of 100, 2mm2 (AWG
14) or thicker wire, or your countrys applicable standard. (Same for
FG and SG terminals)
Cooling Method Natural air circulation

Structure *1 IP65f NEMA #250 TYPE 4X/13 IP66k NEMA #250 TYPE 4X/13
(on the front panel when properly (on the front panel when properly
installed in an enclosure) installed in an enclosure)*2
External Dimensions W169.5 x H137 x D59.5 mm W213.5 x H181 x D59.5 mm
(W6.67 x H5.39 x D2.34 in.) (W8.41 x H7.13 x D2.34 in.)
Panel Cut Dimensions W156 x H123.5 mm (W6.14 x W195 x H162.5 mm (W7.68 x
H4.86 in.) *3 H6.40 in.) *3
Panel thickness area: 1.6...5 mm Panel thickness area: 1.6...5 mm
(0.06...0.2 in.) *4 (0.06...0.2 in.) *4
Weight 0.8 kg (1.8 lbs) or less (main unit 1.2 kg (2.6 lbs) or less (main unit
only) only)

NOTE: *1 The front face of the Magelis GTO, installed in a solid panel, has been tested using conditions
equivalent to the standards shown in the specification. Even though the Magelis GTOs level of resistance
is equivalent to these standards, oils that should have no effect on the Magelis GTO can possibly harm
the panel. This can occur in areas where either vaporized oils are present, or where low viscosity cutting
oils are allowed to adhere to the panel for long periods of time. If the panels front face protection sheet
peels off, these conditions can lead to the ingress of oil into the panel and separate protection measures
are suggested.
*2 When installing the Magelis GTO in a panel, you may not be able to mount the Magelis GTO flush with

the panel. This occurs due to the thickness of the gasket. The difference in level between the Magelis
GTO and panel depends on how much the gasket is compressed.

NOTICE
EQUIPMENT DAMAGE
For food and beverage and pharmaceutical industries, when the Magelis GTO is not flush with panel,
use silicon to form a seal to prevent water, chemicals, or food from lodging into place. Otherwise, the
panel face could leak.
Failure to follow these instructions can result in equipment damage.

*3 For dimensional tolerance, everything +1/-0 mm (+0.04/-0 in.) and R in angle are below R3 (R0.12 in.)
*4
Even if the installation wall thickness is within the recommended range for the Panel Cut Dimensions,
depending on walls material, size, and installation location of the panel and other devices, the installation
wall could warp. To prevent warping, the installation surface may need to be strengthened.

CAUTION
EQUIPMENT DAMAGE
Ensure that the panel is not in permanent and direct contact with oils.
Failure to follow these instructions can result in injury or equipment damage.

NOTICE
STORAGE AND OPERATION OUTSIDE OF SPECIFICATIONS
z Store the panel in areas where temperatures are within the panels specifications.
z Do not restrict or block the panels rear-face ventilation slots.
Failure to follow these instructions can result in equipment damage.

EIO0000001133 02/2012 53
Specifications

NOTICE
GASKET AGING
z Inspect the gasket periodically as required by your operating environment to keep the initial IP level.
z Change the gasket at least once a year, or as soon as scratches or dirt become visible.
Failure to follow these instructions can result in equipment damage.

54 EIO0000001133 02/2012
 Specifications

Display Specifications

Display Type TFT Color LCD

Display Size 5.7
Resolution (pixels) 320 x 240 pixels (QVGA)
Effective Display Area W115.2 x H86.4 mm (W4.54 x H3.40 in.)
Display Colors 65,536 colors (No blink) / 16,384 colors (Blink)
Backlight White LED (Not user-replaceable. When
replacement is required, contact your local
distributor.)
Backlight Service Life 50,000 hours or more (continuous operation at 25 C
[77 F] before backlight decreases to 50%.)
Brightness Control 16 levels (Adjusted with touch panel or software)
Language Fonts ASCII: (Code page 850) Alphanumeric (including
European characters)
Chinese: (GB2312-80 codes) Simplified Chinese
fonts
Japanese (except for XBT GT1000 series): ANK
158, Kanji: 6,962 (JIS Standards 1 & 2) (including
607 non-kanji characters)
Korean: (KSC5601 - 1992 codes) Hangul fonts
Taiwanese: (Big 5 codes) Traditional Chinese fonts
Character Sizes 8 x 8, 8 x 16, 16 x 16 and 32 x 32 pixel fonts
Font Sizes You can expand the width up to 8 times, and expand
the height up to 8 times.*1
Text 8 x 8 pixels 40 characters per row x 30 rows
8 x 16 pixels 40 characters per row x 15 rows
16 x 16 pixels 20 characters per row x 15 rows
32 x 32 pixels 10 characters per row x 7 rows

*1
You can set up other font sizes using the software.

EIO0000001133 02/2012 55
Specifications

Memory, Clock, and Touch Panel

Memory

HMIGTO2310 / HMIGTO2300
HMIGTO2315

Application Memory *1 FLASH EPROM 96 MB FLASH EPROM 64 MB

Data Backup SRAM 512 KB SRAM 128 KB

(Replaceable lithium (Rechargeable lithium
battery for backup battery for backup
memory) memory)

*1
Capacity available for user application.
NOTE:
z When the message Battery level is low is displayed, supply power to the panel and fully charge.
z The rechargeable battery charges within 24 hours to a level which allows backup operation.
Completing a full charge requires about 120 hours (5 days).
z The lifetime of the rechargeable lithium battery is 10 years when the batterys ambient temperature is
40 C (104 F) or less, 4.1 years when the batterys ambient temperature is 50 C (122 F) or less, and
1.5 years when the batterys ambient temperature is 60 C (140 C) or less.
When used for backup:
Approximately 100 days with a fully charged battery.
Approximately 6 days with a half-charged battery.

Clock

Clock Accuracy*1 65 seconds/month (deviation at room temperature

and power is OFF).

*1
Depending on the operating temperature and age of panel, the clock can deviate from -380 to +90
sec/month. For systems where this level of precision is insufficient, the user should monitor and make
adjustments when required.

Touch Panel

Touch Panel Type Resistive Film (analog)

Touch Panel Resolution 1,024 x 1,024
Touch Panel Service Life 1 million times or more

56 EIO0000001133 02/2012
 Specifications

Interface Specifications

Serial Interface COM1

Asynchronous RS-232C
Transmission
Data Length 7 or 8 bits
Stop Bit 1 or 2 bits
Parity None, odd or even
Data Transmission Speed 2,400...115,200 bps
Connector D-Sub 9 pin (plug)

Serial Interface COM2

Asynchronous RS-485
Transmission
Data Length 7 or 8 bits
Stop Bit 1 or 2 bits
Parity None, odd or even
Data Transmission Speed 2,400...115,200 bps, 187,500 bps (MPI)
Connector Modular jack (RJ-45)

USB Interface

USB (Type A) Interface USB (mini-B) Interface

Connector USB 2.0 (Type A) x 1 USB 2.0 (mini-B) x 1
Power Supply Voltage 5 Vdc 5% -
Maximum Current 500 mA -
Supplied
Maximum Transmission 5 m (16.4 ft)
Distance

Ethernet Interface

HMIGTO2310 / HMIGTO2315
Ethernet (LAN) IEEE802.3i / IEEE802.3u,
10BASE-T/100BASE-TX
Connector Modular jack (RJ45) x 1

SD Card Interface
HMIGTO2310/HMIGTO2315: SD Card slot x 1 (maximum 32 GB SD/SDHC Card)
NOTE: HMIGTO2300 does not have an SD Card interface.

EIO0000001133 02/2012 57
Specifications

Specifications of Serial Interface COM1

Introduction
The serial port is not isolated. The SG (signal ground) and FG (frame ground) terminals are connected
inside the panel.

DANGER
ELECTRIC SHOCK
When using the SG terminal to connect an external device to the panel:
z Verify that a short-circuit loop is not created when you set up the system.
z Connect the #5 SG terminal to remote equipment when the host (PLC) unit is not isolated. Connect
the #5 SG terminal to a known reliable ground connection to reduce the risk of damaging the circuit.
Failure to follow these instructions will result in death or serious injury.

Serial Interface COM1

HMIGTO2300 / HMIGTO2310/ HMIGTO2315: D-Sub 9 pin plug connector via an RS-232C cable.

Pin Connection Pin RS-232C

No. Signal Name Direction Meaning
1 CD Input Carrier Detect
2 RD(RXD) Input Receive Data
3 SD(TXD) Output Send Data
4 ER(DTR) Output Data Terminal Ready
5 SG - Signal Ground
6 DR(DSR) Input Data Set Ready
7 RS(RTS) Output Request to Send
8 CS(CTS) Input Send possible
9 CI(RI)/VCC Input/ Called Status Display
+5V5% Output 0.25A
Shell FG Frame Ground (Common
with SG)

You can switch between RI and VCC via software.

NOTICE
EQUIPMENT DAMAGE
Use only the rated current.
Failure to follow these instructions can result in equipment damage.

Interfit bracket is #4-40 (UNC).

CAUTION
LOSS OF COMMUNICATION
z Do not put excessive stress on the communication ports.
z Securely attach communication cables to the panel wall or cabinet.
z Use only D-Sub 9 pin cables with a locking tab in good condition.
Failure to follow these instructions can result in injury or equipment damage.

58 EIO0000001133 02/2012
 Specifications

Specifications of Serial Interface COM2

Introduction
The serial port is not isolated. The SG (signal ground) and FG (frame ground) terminals are connected
inside the panel.

DANGER
ELECTRIC SHOCK
When using the SG terminal to connect an external device to the panel:
z Verify that a short-circuit loop is not created when you set up the system.
z Connect the #8 SG terminal to remote equipment when the host (PLC) unit is not isolated. Connect
the #8 SG terminal to a known reliable ground connection to reduce the risk of damaging the circuit.
Failure to follow these instructions will result in death or serious injury.

Serial Interface COM2

HMIGTO2300 / HMIGTO2310/ HMIGTO2315: RJ45 connector via an RS-485 cable.
NOTE: When setting up RS-485 communication, the cable diagram for some equipment may require
polarization on the terminal side. This terminal does not require any special setting as it handles
polarization automatically.

Pin Connection Pin RS-422/RS-485

No. Signal Name Direction Meaning
1 NC - -
Front
2 NC - -
3 NC - -
4 Line A Input/Output Transfer Data (RS-485)
5 Line B Input/Output Transfer Data (RS-485)
6 RS(RTS) Output Request To Send
7 NC - -
8 SG - Signal Ground

CAUTION
LOSS OF COMMUNICATION
z Do not put excessive stress on the communication ports.
z Securely attach communication cables to the panel wall or cabinet.
z Use only RJ45 with a locking tab in good condition.
Failure to follow these instructions can result in injury or equipment damage.

EIO0000001133 02/2012 59
Specifications

Dimensions

External Dimensions: HMIGTO2300/HMIGTO2310

(3)

mm
in.

155.5
6.12
59.5
169.5 2.34
6.67 5
0.20

5.39

4.84
137

123
(1) (2)

1 Front
2 Right Side
3 Top

External Dimensions: HMIGTO2315

(3)
mm
in.

194.5
7.66
213.5 59.5
8.41 2 2.34
0.08
7.13
181

6.38
162

(1) (2)

1 Front
2 Right Side
3 Top

60 EIO0000001133 02/2012
 Specifications

Installation with Installation Fasteners: HMIGTO2300/HMIGTO2310

(4)
mm
in. 119
4.69

155.5
6.12
59.5
169.5 2.34
6.67 5
0.20

5.79
5.39

4.84

147
137

123
(1) (2) (3)

132
5.20
(5)

1 Left Side
2 Front
3 Right Side
4 Top
5 Bottom

EIO0000001133 02/2012 61
Specifications

Installation with Installation Fasteners: HMIGTO2315

(4)
mm
in.
210.5
8.29

194.5
7.66
59.5
213.5 2.34
8.41 2
0.08

7.13

6.38

7.01
181

162

178
(1) (2) (3)

(5)

1 Left Side
2 Front
3 Right Side
4 Top
5 Bottom

Dimensions with Cables: HMIGTO2300

(4)
mm
in.

62
2.44 34
1.34

4
0.16
0.98
25
2.52

(1) (2) (3)

64

(5)

1 Left Side
2 Rear
3 Right Side
4 Top
5 Bottom

62 EIO0000001133 02/2012
 Specifications

NOTE: All the above values are designed with cable bending in mind. The dimensions given here are
representative values depending on the type of connection cable in use. Therefore, these values are
intended for reference only.

Dimensions with Cables: HMIGTO2310

mm (4)
in.

62
2.44 34
1.34

4
0.16
0.98
25
1.69
43

(1) (2) (3)

2.52
64

(5)

1 Left Side
2 Rear
3 Right Side
4 Top
5 Bottom
NOTE: All the above values are designed with cable bending in mind. The dimensions given here are
representative values depending on the type of connection cable in use. Therefore, these values are
intended for reference only.

EIO0000001133 02/2012 63
Specifications

Dimensions with Cables: HMIGTO2315

(4)

mm
in.

42
1.65 14
0.55 PANEL

0.24
6

0.91
23
1.73
44

(1) (2) (3)

(5)

1 Left Side
2 Rear
3 Right Side
4 Top
5 Bottom
NOTE: All the above values are designed with cable bending in mind. The dimensions given here are
representative values depending on the type of connection cable in use. Therefore, these values are
intended for reference only.

Panel Cut Dimensions

Create a panel cut and insert the panel into the opening from the front.

A
R C
B

A B C R
HMIGTO2310 156 mm (+1/-0) mm 123.5 mm (+1, -0 mm) 1.6...5 mm 3 mm (0.12 in.)
HMIGTO2300 (6.14 in. [+0.04, -0 in.]) (4.86 in. [+0.04, -0 in.]) (0.06...0.2 in.) maximum
HMIGTO2315 195 mm (+1/-0) mm 162.5 mm (+1/-0) mm
(7.68 in. [+0.04, -0 in.]) (6.40 in. [+0.04, -0 in.])

NOTE: Before designing the panel cut, refer to Installation (see page 112).

64 EIO0000001133 02/2012
 Specifications

Installation Fastener Dimensions

mm
in. 14
0
1 .39 M6 0.55
0

0.47
12
12
0.47

26
1.02

EIO0000001133 02/2012 65
Specifications

4.3 HMIGTO3510/4310

Whats in this Section?

This section contains the following topics:
Topic Page
Electrical Specifications 67
Environmental Specifications 68
Structural Specifications 69
Display Specifications 70
Memory, Clock, Touch Panel, and Function Switches 71
Interface Specifications 72
Specifications of Serial Interface COM1 73
Specifications of Serial Interface COM2 74
Dimensions 75

66 EIO0000001133 02/2012
 Specifications

Electrical Specifications

Rated Input Voltage 24 Vdc

Input Voltage Limits 19.2...28.8 Vdc
Voltage Drop 5 ms or less
Power Supply

Power Consumption 12 W or less

When power is not supplied to 8 W or less
external devices
Backlight OFF (Standby Mode) 5 W or less
Backlight Dimmed (Brightness: 5.5 W or less
20%)
In-Rush Current 30 A or less
Voltage Endurance 1,000 Vac, 20 mA for 1 min.
(between charging and FG
terminals)
Insulation Resistance 500 Vdc, 10 M or more
(between charging and FG
terminals)

EIO0000001133 02/2012 67
Specifications

Environmental Specifications

HMIGTO4310 HMIGTO3510
Surrounding air 0...55 C (32...131 F) 0...50 C (32...122 F)
temperature
Physical Environment
Storage temperature -20...60 C (-4...140 F)
Surrounding Air and 10...90% RH (Non condensing, wet bulb temperature 39 C
Storage Humidity [102.2 F] or less)
Dust 0.1 mg/m3 (10-7 oz./ft3) or less (non-conductive levels)
Pollution Degree For use in Pollution Degree 2 environment
Corrosive Gases Free of corrosive gases
Atmospheric pressure 800...1,114 hPa (2,000 m [6,561 ft] or lower)
Vibration Resistance IEC/EN 61131-2
Electrical Environment Mechanical Environment

5...9 Hz Single amplitude 3.5 mm (0.14 in.)

9...150 Hz Fixed acceleration: 9.8 m/s2
X, Y, Z directions for 10 cycles (approx. 100 min.)
Concussion Resistance IEC/EN 61131-2 compliant
147 m/s2, X, Y, Z directions for 3 times

Noise Immunity Noise Voltage: 1000 Vp-p

Pulse Width: 1 s
Rise Time: 1 ns
Electrostatic Discharge Contact Discharge Method: 6 kV (IEC/EN61000-4-2 Level 3)
Immunity

Air quality requirements

Do not operate or store the panel where chemicals evaporate, or where chemicals are present in the air:
z Corrosive chemicals: Acids, alkalines, liquids containing salt.
z Flammable chemicals: Organic solvents.

CAUTION
INOPERATIVE EQUIPMENT
Do not allow water, liquids, metal, and wiring fragments to enter the panel case.
Failure to follow these instructions can result in injury or equipment damage.

68 EIO0000001133 02/2012
 Specifications

Structural Specifications

Grounding Functional grounding: Grounding resistance of

100, 2mm2 (AWG 14) or thicker wire, or your
countrys applicable standard. (Same for FG and
SG terminals)
Cooling Method Natural air circulation

Structure *1 IP65f NEMA #250 TYPE 4X/13 (on the front panel
when properly installed in an enclosure)
External Dimensions W218 x H173 x D60 mm (W8.58 x H6.85 x D2.36
in.)
Panel Cut Dimensions W204.5 x H159.5 mm (W8.05 x H6.28 in.)*2
Panel thickness area: 1.6...5 mm (0.06...0.2 in.)*3
Weight 1.2 kg (2.6 lbs) or less (main unit only)

NOTE: *1 The front face of the Magelis GTO, installed in a solid panel, has been tested using conditions
equivalent to the standards shown in the specification. Even though the Magelis GTOs level of resistance
is equivalent to these standards, oils that should have no effect on the Magelis GTO can possibly harm
the panel. This can occur in areas where either vaporized oils are present, or where low viscosity cutting
oils are allowed to adhere to the panel for long periods of time. If the panels front face protection sheet
peels off, these conditions can lead to the ingress of oil into the panel and separate protection measures
are suggested.
*2
For dimensional tolerance everything +1/-0 mm (+0.04/-0 in.) and R in angle are below R3 (R0.12in.)
*3 Even if the installation wall thickness is within the recommended range for the Panel Cut Dimensions,

depending on walls material, size, and installation location of the panel and other devices, the installation
wall could warp. To prevent warping, the installation surface may need to be strengthened.

CAUTION
EQUIPMENT DAMAGE
Ensure that the panel is not in permanent and direct contact with oils.
Failure to follow these instructions can result in injury or equipment damage.

NOTICE
STORAGE AND OPERATION OUTSIDE OF SPECIFICATIONS
z Store the panel in areas where temperatures are within the panels specifications.
z Do not restrict or block the panels rear-face ventilation slots.
Failure to follow these instructions can result in equipment damage.

NOTICE
GASKET AGING
z Inspect the gasket periodically as required by your operating environment to keep the initial IP level.
z Change the gasket at least once a year, or as soon as scratches or dirt become visible.
Failure to follow these instructions can result in equipment damage.

EIO0000001133 02/2012 69
Specifications

Display Specifications

HMIGTO4310 HMIGTO3510
Display Type TFT Color LCD
Display Size 7.5 7.0
Resolution 640 x 480 pixels (VGA) 800 x 480 pixels (WVGA)
Effective Display Area W153.7 x H115.8 mm W152.4 x H91.44 mm
W6.05 x H4.56 in. W6.0 x H3.6 in.
Display Colors 65,536 colors (No blink) / 16,384 colors Blink)
Backlight White LED (Not user-replaceable. When
replacement is required, contact your local
distributor.)
Backlight Service Life 50,000 hours or more (continuous operation at 25 C
[77 F] before backlight brightness decreases to
50%)
Brightness Control 16 levels (Adjusted with the touch panel or software)
Language Fonts ASCII: (Code page 850) Alphanumeric (including
European characters)
Chinese: (GB2312-80 codes) Simplified Chinese
fonts
Japanese (except for XBT GT1000 series): ANK
158, Kanji: 6,962 (JIS Standards 1 & 2) (including
607 non-kanji characters)
Korean: (KSC5601 - 1992 codes) Hangul fonts
Taiwanese: (Big 5 codes) Traditional Chinese fonts
Character sizes 8 x 8, 8 x 16, 16 x 16 and 32 x 32 pixel fonts
Font sizes You can expand the width up to 8 time, and expand
the height up to 8 times.*1
Text 8 x 8 pixels 80 characters per row x 100 characters per row x
60 rows 60 rows
8 x 16 pixels 80 characters per row x 100 characters per row x
30 rows 30 rows
16 x 16 pixels 40 characters per row x 50 characters per row x
30 rows 30 rows
32 x 32 pixels 20 characters per row x 25 characters per row x
15 rows 15 rows

*1 You can set up other font sizes using the software.

70 EIO0000001133 02/2012
 Specifications

Memory, Clock, Touch Panel, and Function Switches

Memory

HMIGTO4310 HMIGTO3510

Application Memory *1 FLASH EPROM 96 MB FLASH EPROM 96 MB

Data Backup SRAM 512 KB SRAM 128 KB

(Replaceable lithium (Replaceable lithium
battery for backup battery for backup
memory) memory)

*1
Capacity available for user application.
NOTE:
z When the message Battery level is low is displayed, supply power to the panel and fully charge.

Clock

Clock Accuracy*1 65 seconds/month (deviation at room temperature

and power is OFF).

*1 Depending on the operating temperature and age of panel, the clock can deviate from -380 to +90
sec/month. For systems where this level of precision is insufficient, the user should monitor and make
adjustments when required.

Touch Panel

Touch Panel Type Resistive Film (analog)

Touch Panel Resolution 1,024 x 1,024
Touch Panel Service Life 1 million times or more

Function Switches
HMIGTO3510: Eight switches (F1 to F8).

EIO0000001133 02/2012 71
Specifications

Interface Specifications

Serial Interface COM1

Asynchronous Transmission RS-232C

Data Length 7 or 8 bits
Stop Bit 1 or 2 bits
Parity None, odd or even
Data Transmission Speed 2,400...115,200 bps
Connector D-Sub 9 pin (plug)

Serial Interface COM2

Asynchronous Transmission RS-485

Data Length 7 or 8 bits
Stop Bit 1 or 2 bits
Parity None, odd or even
Data Transmission Speed 2,400...115,200 bps,
187,500 bps (MPI)
Connector Modular jack (RJ-45)

USB Interface

USB (Type A) Interface USB (mini-B) Interface

Connector USB 2.0 (Type A) x 1 USB 2.0 (mini-B) x 1
Power Supply Voltage 5 Vdc 5% -
Maximum Current 500 mA -
Supplied
Maximum Transmission 5 m (16.4 ft)
Distance

Ethernet Interface

Ethernet (LAN) IEEE802.3i / IEEE802.3u,

10BASE-T/100BASE-TX
Connector Modular jack (RJ45) x 1

SD Card Interface
SD Card slot x 1 (maximum 32 GB SD/SDHC Card)

72 EIO0000001133 02/2012
 Specifications

Specifications of Serial Interface COM1

Introduction
The serial port is not isolated. The SG (signal ground) and FG (frame ground) terminals are connected
inside the panel.

DANGER
ELECTRIC SHOCK
When using the SG terminal to connect an external device to the panel:
z Verify that a short-circuit loop is not created when you set up the system.
z Connect the #5 SG terminal to remote equipment when the host (PLC) unit is not isolated. Connect
the #5 SG terminal to a known reliable ground connection to reduce the risk of damaging the circuit.
Failure to follow these instructions will result in death or serious injury.

Serial Interface COM1

HMIGTO3510 / HMIGTO4310: D-Sub 9 pin plug connector via an RS-232C cable.

Pin Connection Pin RS-232C

No. Signal Name Direction Meaning
1 CD Input Carrier Detect
2 RD(RXD) Input Receive Data
3 SD(TXD) Output Send Data
4 ER(DTR) Output Data Terminal Ready
5 SG - Signal Ground
6 DR(DSR) Input Data Set Ready
7 RS(RTS) Output Request to Send
8 CS(CTS) Input Send possible
9 CI(RI)/VCC Input/ Called Status Display
+5V5% Output 0.25A
Shell FG Frame Ground (Common
with SG)

You can switch pin #9 between RI and VCC via software.

NOTICE
EQUIPMENT DAMAGE
Use only the rated current.
Failure to follow these instructions can result in equipment damage.

Interfit bracket is #4-40 (UNC).

CAUTION
LOSS OF COMMUNICATION
z Do not put excessive stress on the communication ports.
z Securely attach communication cables to the panel wall or cabinet.
z Use only D-Sub 9 pin cables with a locking tab in good condition.
Failure to follow these instructions can result in injury or equipment damage.

EIO0000001133 02/2012 73
Specifications

Specifications of Serial Interface COM2

Introduction
The serial port is not isolated. The SG (signal ground) and FG (frame ground) terminals are connected
inside the panel.

DANGER
ELECTRIC SHOCK
When using the SG terminal to connect an external device to the panel:
z Verify that a short-circuit loop is not created when you set up the system.
z Connect the #8 SG terminal to remote equipment when the host (PLC) unit is not isolated. Connect
the #8 SG terminal to a known reliable ground connection to reduce the risk of damaging the circuit.
Failure to follow these instructions will result in death or serious injury.

Serial Interface COM2

HMIGTO3510 / HMIGTO4310: RJ45 connector via a RS-485 cable.
NOTE: When setting up RS-485 communication, the cable diagram for some equipment may require
polarization on the terminal side. This terminal does not require any special setting as it handles
polarization automatically.

Pin Connection Pin RS-485

No. Signal Name Direction Meaning
1 NC - -
Front
2 NC - -
3 NC - -
4 Line A Input/Output Transfer Data (RS-485)
5 Line B Input/Output Transfer Data (RS-485)
6 RS(RTS) Output Request To Send
7 NC - -
8 SG - Signal Ground

CAUTION
LOSS OF COMMUNICATION
z Do not put excessive stress on the communication ports.
z Securely attach communication cables to the panel wall or cabinet.
z Use only RJ45 with a locking tab in good condition.
Failure to follow these instructions can result in injury or equipment damage.

74 EIO0000001133 02/2012
 Specifications

Dimensions

External Dimensions: HMIGTO3510

mm (3)
in.

204
8.03
60
218 2.36
8.58 5
0.20

6.81
173

6.26
159
(1) (2)

1 Front
2 Right Side
3 Top

External Dimensions: HMIGTO4310

mm (3)
in.

204
8.03
60
218 2.36
8.58 5
0.20
6.26
159
6.81
173

(1) (2)

1 Front
2 Right Side
3 Top

EIO0000001133 02/2012 75
Specifications

Installation with Installation Fasteners: HMIGTO3510

(4)
mm
in. 166
6.54

204
8.03
60
218
5 2.36
8.58
0.20

6.26
6.81

159

7.20
173

183
(1) (2) (3)

166
6.54
(5)

1 Left Side
2 Front
3 Right Side
4 Top
5 Bottom

Installation with Installation Fasteners: HMIGTO4310

(4)
mm
in. 166
6.54

204
8.03 60
2.36
218 5
8.58 0.20
7.20
6.26
6.81

183
159
173

(1) (2) (3)

166
6.54
(5)
1 Left Side
2 Front
3 Right Side
4 Top
5 Bottom

76 EIO0000001133 02/2012
 Specifications

Dimensions with Cables: HMIGTO3510

mm (4)
in.

23
0.91

0.28
7
1.10
28

(1) (2) (3)

(5)

1 Left Side
2 Rear
3 Right Side
4 Top
5 Bottom
NOTE: All the above values are designed with cable bending in mind. The dimensions given here are
representative values depending on the type of connection cable in use. Therefore, these values are
intended for reference only.

EIO0000001133 02/2012 77
Specifications

Dimensions with Cables: HMIGTO4310

mm ()
in.

23
0.91

0.28
7
1.10
28

(1) (2) ()

()

1 Left Side
2 Rear
3 Right Side
4 Top
5 Bottom
NOTE: All the above values are designed with cable bending in mind. The dimensions given here are
representative values depending on the type of connection cable in use. Therefore, these values are
intended for reference only.

Panel Cut Dimensions

Create a panel cut and insert the panel into the opening from the front.

A
R C
B

A B C R
204.5 mm (+1, -0 mm) 159.5 mm (+1, -0 mm) 1.6...5 mm 3 mm (0.12 in.)
(8.05 in. [+0.04, -0 in.]) (6.28 in. [+0.04, -0 in.]) (0.06...0.2 in.) maximum

NOTE: Before designing the panel cut, refer to Installation (see page 112).

78 EIO0000001133 02/2012
 Specifications

Installation Fastener Dimensions

mm
in. 14
0
1 .39 M6 0.55
0

0.47
12
12
0.47

26
1.02

EIO0000001133 02/2012 79
Specifications

4.4 HMIGTO5310/5315

Whats in this Section?

This section contains the following topics:
Topic Page
Electrical Specifications 81
Environmental Specifications 82
Structural Specifications 83
Display Specifications 85
Memory, Clock, and Touch Panel 86
Interface Specifications 87
Specifications of Serial Interface COM1 88
Specifications of Serial Interface COM2 89
Dimensions 90

80 EIO0000001133 02/2012
 Specifications

Electrical Specifications

Rated Input Voltage 24 Vdc

Input Voltage Limits 19.2...28.8 Vdc
Voltage Drop 10 ms or less
Power Consumption 17 W or less
Power Supply

When power is not supplied to 12 W or less

external devices
Backlight OFF (Standby 7 W or less
Mode)
Backlight Dimmed 8 W or less
(Brightness: 20%)
In-Rush Current 30 A or less
Voltage Endurance 1500 Vac, 20 mA for 1 min.
(between charging and FG
terminals)
Insulation Resistance 500 Vdc, 10 M or more
(between charging and FG
terminals)

EIO0000001133 02/2012 81
Specifications

Environmental Specifications

Surrounding Air Temperature 0...55 C (32...131 F)

Storage Temperature -20...60 C (-4...140 F)

Physical Environment Surrounding Air and Storage 10...90% RH (Non condensing, wet
Humidity bulb temperature 39 C [102.2 F] or
less)
Dust 0.1 mg/m3 (10-7 oz./ft3) or less (non-
conductive levels)
Pollution Degree For use in Pollution Degree 2
environment
Corrosive Gases Free of corrosive gases
Atmospheric Pressure 800...1,114 hPa (2,000 m [6,561 ft] or
(Operating Altitude) lower)
Vibration Resistance IEC/EN 61131-2 compliant
Electrical Environment Mechanical Environment

5...9 Hz Single amplitude 3.5 mm (0.14

in.)
9...150 Hz Fixed acceleration: 9.8 m/s2
X, Y, Z directions for 10 cycles (approx.
100 min.)
Concussion Resistance IEC/EN 61131-2 compliant
147 m/s2, X, Y, Z directions for 3 times
Noise Immunity Noise Voltage: 1,000 Vp-p
Pulse Width: 1 s
Rise Time: 1 ns
Electrostatic Discharge Contact Discharge Method: 6 kV
Immunity (IEC/EN61000-4-2 Level 3)

Air quality requirements

Do not operate or store the panel where chemicals evaporate, or where chemicals are present in the air:
z Corrosive chemicals: Acids, alkalines, liquids containing salt.
z Flammable chemicals: Organic solvents.

CAUTION
INOPERATIVE EQUIPMENT
Do not allow water, liquids, metal, and wiring fragments to enter the panel case.
Failure to follow these instructions can result in injury or equipment damage.

82 EIO0000001133 02/2012
 Specifications

Structural Specifications

HMIGTO5310 HMIGTO5315
Grounding Functional grounding: Grounding resistance of 100,
2mm2 (AWG 14) or thicker wire, or your countrys
applicable standard. (Same for FG and SG terminals)
Cooling Method Natural air circulation

Structure *1 IP65f NEMA #250 TYPE IP66k NEMA #250 TYPE

4X/13 (on the front panel 4X/13 (on the front panel
when properly installed in when properly installed in
an enclosure) an enclosure)*2
External Dimensions W272.5 x H214.5 x D57 W316.5 x H258.5 x D57
mm (W10.73 x H8.44 x mm (W12.44 x H10.18 x
D2.24 in.) D2.24 in.)
Panel Cut Dimensions W259 x H201 mm (W10.2 x W298 x H240 mm (W11.73
H7.91 in.)*3 x H9.45 in.)*3
Panel thickness area: Panel thickness area:
1.6...5 mm (0.06...0.2 in.)*4 1.6...5 mm (0.06...0.2 in.)*4
Weight 2.0 kg (4.4 lbs) or less 2.5 kg (5.5 lbs) or less
(main unit only) (main unit only)

NOTE: *1 The front face of the Magelis GTO, installed in a solid panel, has been tested using conditions
equivalent to the standards shown in the specification. Even though the Magelis GTOs level of resistance
is equivalent to these standards, oils that should have no effect on the Magelis GTO can possibly harm
the panel. This can occur in areas where either vaporized oils are present, or where low viscosity cutting
oils are allowed to adhere to the panel for long periods of time. If the panels front face protection sheet
peels off, these conditions can lead to the ingress of oil into the panel and separate protection measures
are suggested.
*2 When installing the Magelis GTO in a panel, you may not be able to mount the Magelis GTO flush with

the panel. This occurs due to the thickness of the gasket. The difference in level between the Magelis
GTO and panel depends on how much the gasket is compressed.

NOTICE
EQUIPMENT DAMAGE
For food and beverage and pharmaceutical industries, when the Magelis GTO is not flush with panel,
use silicon to form a seal to prevent water, chemicals, or food from lodging into place. Otherwise, the
panel face could leak.
Failure to follow these instructions can result in equipment damage.

*3
For dimensional tolerance everything +1/-0 mm (+0.04/-0 in.) and R in angle are below R3 (R0.12 in.)
*4 Even if the installation wall thickness is within the recommended range for the Panel Cut Dimensions,

depending on walls material, size, and installation location of the panel and other devices, the installation
wall could warp. To prevent warping, the installation surface may need to be strengthened.

CAUTION
EQUIPMENT DAMAGE
Ensure that the panel is not in permanent and direct contact with oils.
Failure to follow these instructions can result in injury or equipment damage.

EIO0000001133 02/2012 83
Specifications

NOTICE
STORAGE AND OPERATION OUTSIDE OF SPECIFICATIONS
z Store the panel in areas where temperatures are within the panels specifications.
z Do not restrict or block the panels rear-face ventilation slots.
Failure to follow these instructions can result in equipment damage.

NOTICE
GASKET AGING
z Inspect the gasket periodically as required by your operating environment to keep the initial IP level.
z Change the gasket at least once a year, or as soon as scratches or dirt become visible.
Failure to follow these instructions can result in equipment damage.

84 EIO0000001133 02/2012
 Specifications

Display Specifications

Display Type TFT Color LCD

Display Size 10.4
Resolution 640 x 480 pixels (VGA)
Effective Display Area W211.2 x H158.4 mm (8.31 x 6.24 in.)
Display Colors 65,536 colors (No blink) / 16,384 colors
(Blink)
Backlight White LED (Not user-replaceable. When
replacement is required, contract your local
distributor.)
Backlight Service Life 50,000 hours or more (continuous operation
at 25 C [77 F] before backlight brightness
dimmed to 50%
Brightness Control 16 levels (Adjusted with the touch panel or
software)
Language Fonts ASCII: (Code page 850) Alphanumeric
(including European characters)
Chinese: (GB2312-80 codes) Simplified
Chinese fonts
Japanese: ANK 158, Kanji: 6,962 (JIS
Standards 1 & 2) (including 607 non-kanji
characters)
Korean: (KSC5601 - 1992 codes) Hangul
fonts
Taiwanese: (Big 5 codes) Traditional
Chinese fonts
Character Sizes 8 x 8, 8 x 16, 16 x 16 and 32 x 32 pixel fonts
Font Sizes You can expand the width up to 8 times, and
expand the height up to 8 times.*1
Text 8 x 8 pixels 80 characters per row x 60 rows
8 x 16 pixels 80 characters per row x 30 rows
16 x 16 pixels 40 characters per row x 30 rows
32 x 32 pixels 20 characters per row x 15 rows

*1 You can set up other font sizes using the software.

EIO0000001133 02/2012 85
Specifications

Memory, Clock, and Touch Panel

Memory

Application Memory *1 FLASH EPROM 96 MB

Data Backup SRAM 512 KB (Replaceable lithium battery for

backup memory)

*1
Capacity available for user application.
NOTE:
z When the message Battery level is low is displayed, supply power to the panel and fully charge.

Clock

Clock Accuracy*1 65 seconds/month (deviation at room temperature

and power is OFF).

*1 Depending on the operating temperature and age of panel, the clock can deviate from -380 to +90
sec/month. For systems where this level of precision is insufficient, the user should monitor and make
adjustments when required.

Touch Panel

Touch Panel Type Resistive Film (analog)

Touch Panel Resolution 1,024 x 1,024
Service Life 1 million times or more

86 EIO0000001133 02/2012
 Specifications

Interface Specifications

Serial Interface COM1

Asynchronous Transmission RS-232C

Data Length 7 or 8 bits
Stop Bit 1 or 2 bits
Parity None, odd or even
Data Transmission Speed 2,400...115,200 bps
Connector D-Sub 9 pin (plug)

Serial Interface COM2

Asynchronous Transmission RS-485

Data Length 7 or 8 bits
Stop Bit 1 or 2 bits
Parity None, odd or even
Data Transmission Speed 2,400...115,200 bps,
187,500 bps (MPI)
Connector Modular jack (RJ-45)

USB Interface

USB (Type A) Interface USB (mini-B) Interface

Connector USB 2.0 (Type A) x 1 USB 2.0 (mini-B) x 1
Power Supply Voltage 5 Vdc 5% -
Maximum Current 500 mA -
Supplied
Maximum Transmission 5 m (16.4 ft)
Distance

Ethernet Interface

Ethernet (LAN) IEEE802.3i / IEEE802.3u,

10BASE-T/100BASE-TX
Connector Modular jack (RJ45) x 1

SD Card Interface
SD Card slot x 1 (maximum 32 GB SD/SDHC Card)

EIO0000001133 02/2012 87
Specifications

Specifications of Serial Interface COM1

Introduction
The serial port is not isolated. The SG (signal ground) and FG (frame ground) terminals are connected
inside the panel.

DANGER
ELECTRIC SHOCK
When using the SG terminal to connect an external device to the panel:
z Verify that a short-circuit loop is not created when you set up the system.
z Connect the #5 SG terminal to remote equipment when the host (PLC) unit is not isolated. Connect
the #5 SG terminal to a known reliable ground connection to reduce the risk of damaging the circuit.
Failure to follow these instructions will result in death or serious injury.

Serial Interface COM1

HMIGTO5310 / HMIGTO5315: D-Sub 9 pin plug connector via an RS-232C cable.

Pin Connection Pin RS-232C

No. Signal Name Direction Meaning
1 CD Input Carrier Detect
2 RD(RXD) Input Receive Data
3 SD(TXD) Output Send Data
4 ER(DTR) Output Data Terminal Ready
5 SG - Signal Ground
6 DR(DSR) Input Data Set Ready
7 RS(RTS) Output Request to Send
8 CS(CTS) Input Send possible
9 CI(RI)/VCC Input/ Called Status Display
+5V5% Output 0.25A
Shell FG Frame Ground (Common
with SG)

You can switch pin 39 between RI and VCC via software.

NOTICE
EQUIPMENT DAMAGE
Use only the rated current.
Failure to follow these instructions can result in equipment damage.

Interfit bracket is #4-40 (UNC).

CAUTION
LOSS OF COMMUNICATION
z Do not put excessive stress on the communication ports.
z Securely attach communication cables to the panel wall or cabinet.
z Use only D-Sub 9 pin cables with a locking tab in good condition.
Failure to follow these instructions can result in injury or equipment damage.

88 EIO0000001133 02/2012
 Specifications

Specifications of Serial Interface COM2

Introduction
The serial port is not isolated. The SG (signal ground) and FG (frame ground) terminals are connected
inside the panel.

DANGER
ELECTRIC SHOCK
When using the SG terminal to connect an external device to the panel:
z Verify that a short-circuit loop is not created when you set up the system.
z Connect the #8 SG terminal to remote equipment when the host (PLC) unit is not isolated. Connect
the #8 SG terminal to a known reliable ground connection to reduce the risk of damaging the circuit.
Failure to follow these instructions will result in death or serious injury.

Serial Interface COM2

HMIGTO5310 / HMIGTO5315: RJ45 connector via a RS-485 cable.
NOTE: When setting up RS-485 communication, the cable diagram for some equipment may require
polarization on the terminal side. This terminal does not require any special setting as it handles
polarization automatically.

Pin Connection Pin RS-485

No. Signal Name Direction Meaning
1 NC - -
Front
2 NC - -
3 NC - -
4 Line A Input/Output Transfer Data (RS-485)
5 Line B Input/Output Transfer Data (RS-485)
6 RS(RTS) Output Request To Send
7 NC - -
8 SG - Signal Ground

CAUTION
LOSS OF COMMUNICATION
z Do not put excessive stress on the communication ports.
z Securely attach communication cables to the panel wall or cabinet.
z Use only RJ45 with a locking tab in good condition.
Failure to follow these instructions can result in injury or equipment damage.

EIO0000001133 02/2012 89
Specifications

Dimensions

External Dimensions: HMIGTO5310

mm (3)
in.

258.5
10.18

272.5 57
10.73 5 2.24
0.20

200.5
214.5

7.89
8.44
(1) (2)

1 Front
2 Right Side
3 Top

External Dimensions: HMIGTO5315

mm (3)
in.

297.5
11.71

316.5 57
12.46 2 2.24
0.08
258.5
10.18

239.5
9.43

(1) (2)

1 Front
2 Right Side
3 Top

90 EIO0000001133 02/2012
 Specifications

Installation with Installation Fasteners: HMIGTO5310

mm (4)
in. 220
8.66

258.5
10.18 57
2.24
272.5 5
10.73 0.20

8.82
214.5

200.5

224
8.44

7.89
(1) (2) (3)

220
8.66
(5)

1 Left Side
2 Front
3 Right Side
4 Top
5 Bottom

Installation with Installation Fasteners: HMIGTO5315

mm (4)
in.
313.5
12.34

297.5
11.71

316.5 57
12.46 2 2.24
0.08
258.5
10.18

239.5

255.5
10.06
9.43

(1) (2) (3)

(5)

1 Left Side
2 Front
3 Right Side
4 Top
5 Bottom

EIO0000001133 02/2012 91
Specifications

Dimensions with Cables: HMIGTO5310

mm (4)
in.

0.39
0.28 10
7

66 1.50
38

2.60
(1) (2) (3)

(5)

1 Left Side
2 Rear
3 Right Side
4 Top
5 Bottom
NOTE: All the above values are designed with cable bending in mind. The dimensions given here are
representative values depending on the type of connection cable in use. Therefore, these values are
intended for reference only.

92 EIO0000001133 02/2012
 Specifications

Dimensions with Cables: HMIGTO5315

mm (4)
in.

PANEL

0.71

0.35
18

9
1.81
46

(1) (2) (3)

(5)

1 Left Side
2 Rear
3 Right Side
4 Top
5 Bottom
NOTE: All the above values are designed with cable bending in mind. The dimensions given here are
representative values depending on the type of connection cable in use. Therefore, these values are
intended for reference only.

Panel Cut Dimensions

Create a panel cut and insert the panel into the opening from the front.

A
R C
B

A B C R
HMIGTO5310 259 mm (+1, -0 mm) 201 mm (+1, -0 mm) 1.6...5 mm 3 mm (0.12 in.)
(10.2 in. [+0.04, -0 in.]) (7.91 in. [+0.04, -0 in.]) (0.06...0.2 in.) maximum
HMIGTO5315 298 mm (+1, -0 mm) 240 mm (+1, -0 mm)
(11.73 in. [+0.04, -0 in.]) (9.45 in. [+0.04, -0 in.])

NOTE: Before designing the panel cut, refer to Installation (see page 112).

EIO0000001133 02/2012 93
Specifications

Installation Fastener Dimensions

mm
in. 14
0
1 .39 M6 0.55
0

0.47
12
12
0.47

26
1.02

94 EIO0000001133 02/2012
 Specifications

4.5 HMIGTO6310/6315

Whats in this Section?

This section contains the following topics:
Topic Page
Electrical Specifications 96
Environmental Specifications 97
Structural Specifications 98
Display Specifications 100
Memory, Clock, and Touch Panel 101
Interface Specifications 102
Specifications of Serial Interface COM1 103
Specifications of Serial Interface COM2 104
Dimensions 105

EIO0000001133 02/2012 95
Specifications

Electrical Specifications

Rated Input Voltage 24 Vdc

Input Voltage Limits 19.2...28.8 Vdc
Voltage Drop 10 ms or less
Power Consumption 17 W or less
Power Supply

When power is not 12 W or less

supplied to external
devices
Backlight OFF (Standby 7 W or less
Mode)
Backlight Dimmed 8 W or less
(Brightness: 20%)
In-Rush Current 30 A or less
Voltage Endurance 1,500 Vac, 20 mA for 1 min.
(between charging and FG
terminals)
Insulation Resistance 500 Vdc, 10 M or more (between
charging and FG terminals)

96 EIO0000001133 02/2012
 Specifications

Environmental Specifications

Surrounding air 0...55 C (32...131 F)

temperature
Physical Environment Storage Temperature -20 C...+ 60 C (-4 F...140 F)
Surrounding Air and 10...90% RH (Non condensing, wet bulb
Storage Humidity temperature 39 C [102.2 F] or less)
Dust 0.1 mg/m3 (10-7 oz./ft3) or less (non-
conductive levels)
Pollution Degree For use in Pollution Degree 2 environment
Corrosive gases Free of corrosive gases
Atmospheric Pressure 800...1,114 hPa (2,000 m [6,561 ft] or
(Operating Altitude) lower)
Vibration Resistance IEC/EN 61131-2 compliant
Electrical Environment Mechanical Environment

5...9 Hz Single amplitude 3.5 mm (0.14 in.)

9...150 Hz Fixed acceleration: 9.8 m/s2
X, Y, Z directions for 10 cycles (approx.100
min.)
Concussion Resistance IEC/EN 61131-2 compliant
147 m/s2, X, Y, Z directions for 3 times

Noise immunity Noise Voltage: 1000 Vp-p

Pulse Width: 1 s
Rise Time: 1 ns
Electrostatic Discharge Contact Discharge Method: 6 kV
Immunity (IEC/EN61000-4-2 Level 3)

Air quality requirements

Do not operate or store the panel where chemicals evaporate, or where chemicals are present in the air:
z Corrosive chemicals: Acids, alkalines, liquids containing salt.
z Flammable chemicals: Organic solvents.

CAUTION
INOPERATIVE EQUIPMENT
Do not allow water, liquids, metal, and wiring fragments to enter the panel case.
Failure to follow these instructions can result in injury or equipment damage.

EIO0000001133 02/2012 97
Specifications

Structural Specifications

HMIGTO6310 HMIGTO6315
Grounding Functional grounding: Grounding resistance of 100, 2mm2 (AWG
14) or thicker wire, or your countrys applicable standard. (Same for
FG and SG terminals)
Cooling Method Natural air circulation

Structure *1 IP65f NEMA #250 TYPE 4X/13 IP66k NEMA #250 TYPE 4X/13
(on the front panel when properly (on the front panel when
installed in an enclosure) properly installed in an
enclosure)*2
External Dimensions W315 x H241 x D56 mm (W12.4 W359 x H285 x D56 mm
x H9.49 x D2.2 in.) (W14.13 x H11.22 x D2.2 in.)
Panel Cut Dimensions W301.5 x H227.5 mm (W11.87 x W340.5 x H266.5 mm (W13.41
H8.96 in.)*3 x H10.49 in.)*3
Panel thickness area: 1.6...5 mm Panel thickness area: 1.6...5
(0.06...0.2 in.)*4 mm (0.06...0.2 in.)*4
Weight 2.5 kg (5.5 lbs) or less (main unit 3 kg (6.6 lbs) or less (main unit
only) only)

NOTE: *1 The front face of the Magelis GTO, installed in a solid panel, has been tested using conditions
equivalent to the standards shown in the specification. Even though the Magelis GTOs level of resistance
is equivalent to these standards, oils that should have no effect on the Magelis GTO can possibly harm
the panel. This can occur in areas where either vaporized oils are present, or where low viscosity cutting
oils are allowed to adhere to the panel for long periods of time. If the panels front face protection sheet
peels off, these conditions can lead to the ingress of oil into the panel and separate protection measures
are suggested.
*2When installing the Magelis GTO in a panel, you may not be able to mount the Magelis GTO flush with
the panel. This occurs due to the thickness of the gasket. The difference in level between the Magelis
GTO and panel depends on how much the gasket is compressed.

NOTICE
EQUIPMENT DAMAGE
For food and beverage and pharmaceutical industries, when the Magelis GTO is not flush with panel,
use silicon to form a seal to prevent water, chemicals, or food from lodging into place. Otherwise, the
panel face could leak.
Failure to follow these instructions can result in equipment damage.

*3 For dimensional tolerance everything +1/-0 mm (+0.04/-0 in.) and R in angle are below R3 (R0.12in).
*4
Even if the installation wall thickness is within the recommended range for the Panel Cut Dimensions,
depending on walls material, size, and installation location of the panel and other devices, the installation
wall could warp. To prevent warping, the installation surface may need to be strengthened.

CAUTION
EQUIPMENT DAMAGE
Ensure that the panel is not in permanent and direct contact with oils.
Failure to follow these instructions can result in injury or equipment damage.

NOTICE
STORAGE AND OPERATION OUTSIDE OF SPECIFICATIONS
z Store the panel in areas where temperatures are within the panels specifications.
z Do not restrict or block the panels rear-face ventilation slots.
Failure to follow these instructions can result in equipment damage.

98 EIO0000001133 02/2012
 Specifications

NOTICE
GASKET AGING
z Inspect the gasket periodically as required by your operating environment to keep the initial IP level.
z Change the gasket at least once a year, or as soon as scratches or dirt become visible.
Failure to follow these instructions can result in equipment damage.

EIO0000001133 02/2012 99
Specifications

Display Specifications

Display Type TFT Color LCD

Display Size 12.1
Resolution 800 x 600 pixels (SVGA)
Effective Display Area W246.0 x H184.5 mm (9.69 x 7.26 in.)
Display Colors 65,536 colors (No blink) / 16,384 colors
(Blink)
Backlight White LED (Not user-replaceable. When
replacement is required, contact your
local distributor.)
Backlight Service Life 50,000 hours (continuous operation at at
25 C [77 F] before backlight brightness
decreases to 50%)
Brightness Control 16 levels (Adjusted with the touch panel
or software)
Language Fonts ASCII: (Code page 850) Alphanumeric
(including European characters)
Chinese: (GB2312-80 codes) Simplified
Chinese fonts
Japanese: ANK 158, Kanji: 6,962 (JIS
Standards 1 & 2) (including 607 non-
kanji characters)
Korean: (KSC5601 - 1992 codes)
Hangul fonts
Taiwanese: (Big 5 codes) Traditional
Chinese fonts
Character Sizes 8 x 8, 8 x 16, 16 x 16 and 32 x 32 pixel
fonts
Text 8 x 8 pixels 100 characters per row x 75 rows
8 x 16 pixels 100 characters per row x 37 rows
16 x 16 pixels 50 characters per row x 37 rows
32 x 32 pixels 25 characters per row x 18 rows

*1 You can set up other font sizes using the software.

100 EIO0000001133 02/2012

 Specifications

Memory, Clock, and Touch Panel

Memory

Application Memory*1 FLASH EPROM96 MB

Data Backup SRAM 512 KB (Replaceable lithium battery for

backup memory)

*1
Capacity available for user application.
NOTE:
z When the message Battery level is low is displayed, supply power to the panel and fully charge.

Clock

Clock Accuracy*1 65 seconds/month (deviation at room temperature

and power is OFF).

*1 Depending on the operating temperature and age of the panel, the clock can deviate from -380 to +90
sec/month. For systems where this level of precision is insufficient, the user should monitor and make
adjustments when required.

Touch Panel

Touch Panel Type Resistive Film (analog)

Touch Panel Resolution 1,024 x 1,024
Touch Panel Service Life 1 million times or more

EIO0000001133 02/2012 101

Specifications

Interface Specifications

Serial Interface COM1

Asynchronous Transmission RS-232C

Data Length 7 or 8 bits
Stop Bit 1 or 2 bits
Parity None, odd or even
Data Transmission Speed 2,400...115,200 bps
Connector D-Sub 9 pin (plug)

Serial Interface COM2

Asynchronous Transmission RS-485

Data Length 7 or 8 bits
Stop Bit 1 or 2 bits
Parity None, odd or even
Data Transmission Speed 2,400...115,200 bps, 187,500 bps
(MPI)
Connector Modular jack (RJ-45)

USB Interface

USB (Type A) Interface USB (mini-B) Interface

Connector USB 2.0 (Type A) x 1 USB 2.0 (mini-B) x 1
Power Supply Voltage 5 Vdc 5%
Maximum Current 500 mA -
Supplied
Maximum Transmission 5 m (16.4 ft)
Distance

Ethernet Interface

Ethernet (LAN) IEEE802.3i / IEEE802.3u,

10BASE-T/100BASE-TX
Connector Modular jack (RJ45) x 1

SD Card Interface
SD Card slot x 1 (maximum 32 GB SD/SDHC Card)

102 EIO0000001133 02/2012

 Specifications

Specifications of Serial Interface COM1

Introduction
The serial port is not isolated. The SG (signal ground) and FG (frame ground) terminals are connected
inside the panel.

DANGER
ELECTRIC SHOCK
When using the SG terminal to connect an external device to the panel:
z Verify that a short-circuit loop is not created when you set up the system.
z Connect the #5 SG terminal to remote equipment when the host (PLC) unit is not isolated. Connect
the #5 SG terminal to a known reliable ground connection to reduce the risk of damaging the circuit.
Failure to follow these instructions will result in death or serious injury.

Serial Interface COM1

HMIGTO6310 / HMIGTO6315: D-Sub 9 pin plug connector via an RS-232C cable.

Pin Connection Pin RS-232C

No. Signal Name Direction Meaning
1 CD Input Carrier Detect
2 RD(RXD) Input Receive Data
3 SD(TXD) Output Send Data
4 ER(DTR) Output Data Terminal Ready
5 SG - Signal Ground
6 DR(DSR) Input Data Set Ready
7 RS(RTS) Output Request to Send
8 CS(CTS) Input Send possible
9 CI(RI)/VCC Input/ Called Status Display
+5V5% Output 0.25A
Shell FG Frame Ground (Common
with SG)

You can switch pin #9 between RI and VCC via software.

NOTICE
EQUIPMENT DAMAGE
Use only the rated current.
Failure to follow these instructions can result in equipment damage.

Interfit bracket is #4-40 (UNC).

CAUTION
LOSS OF COMMUNICATION
z Do not put excessive stress on the communication ports.
z Securely attach communication cables to the panel wall or cabinet.
z Use only D-Sub 9 pin cables with a locking tab in good condition.
Failure to follow these instructions can result in injury or equipment damage.

EIO0000001133 02/2012 103

Specifications

Specifications of Serial Interface COM2

Introduction
The serial port is not isolated. The SG (signal ground) and FG (frame ground) terminals are connected
inside the panel.

DANGER
ELECTRIC SHOCK
When using the SG terminal to connect an external device to the panel:
z Verify that a short-circuit loop is not created when you set up the system.
z Connect the #8 SG terminal to remote equipment when the host (PLC) unit is not isolated. Connect
the #8 SG terminal to a known reliable ground connection to reduce the risk of damaging the circuit.
Failure to follow these instructions will result in death or serious injury.

Serial Interface COM2

HMIGTO6310 / HMIGTO6315: RJ45 connector via a RS-485 cable.
NOTE: When setting up RS-485 communication, the cable diagram for some equipment may require
polarization on the terminal side. This terminal does not require any special setting as it handles
polarization automatically.

Pin Connection Pin RS-485

No. Signal Name Direction Meaning
1 NC - -
Front
2 NC - -
3 NC - -
4 Line A Input/Output Transfer Data (RS-485)
5 Line B Input/Output Transfer Data (RS-485)
6 RS(RTS) Output Request To Send
7 NC - -
8 SG - Signal Ground

CAUTION
LOSS OF COMMUNICATION
z Do not put excessive stress on the communication ports.
z Securely attach communication cables to the panel wall or cabinet.
z Use only RJ45 with a locking tab in good condition.
Failure to follow these instructions can result in injury or equipment damage.

104 EIO0000001133 02/2012

 Specifications

Dimensions

External Dimensions: HMIGTO6310

(3)
mm
in.

301
11.85

56
315 2.20
12.40 5
0.20

9.49
(1) 241 (2)

1 Front
2 Right Side
3 Top

External Dimensions: HMIGTO6315

mm (3)
in.

340
13.39

359 56
14.13 2 2.20
0.08
10.47
11.22
285

266

(1) (2)

1 Front
2 Right Side
3 Top

EIO0000001133 02/2012 105

Specifications

Installation with Installation Fasteners: HMIGTO6310

(4)
mm
in. 260
10.24

301
11.85
56
315 2.20
12.40 5
0.20

9.88
9.49

251
241
(1) (2) (3)

260
10.24
(5)

1 Left Side
2 Front
3 Right Side
4 Top
5 Bottom

Installation with Installation Fasteners: HMIGTO6315

(4)
mm
in. 356
14.02

340
13.39

359 56
14.13 2 2.20
0.08
10.47
11.22

11.10
285

266

282

(1) (2) (3)

(5)

1 Left Side
2 Front
3 Right Side
4 Top
5 Bottom

106 EIO0000001133 02/2012

 Specifications

Dimensions with Cables: HMIGTO6310

(4)

mm
in.

0.98
25

2.09
53
(1) (2) (3)

(5)

1 Left Side
2 Rear
3 Right Side
4 Top
5 Bottom
NOTE: All the above values are designed with cable bending in mind. The dimensions given here are
representative values depending on the type of connection cable in use. Therefore, these values are
intended for reference only.

EIO0000001133 02/2012 107

Specifications

Dimensions with Cables: HMIGTO6315

mm (4)
in.

PANEL

0.20
1.30 5
33

(1) (2) (3)

(5)

1 Left Side
2 Rear
3 Right Side
4 Top
5 Bottom
NOTE: All the above values are designed with cable bending in mind. The dimensions given here are
representative values depending on the type of connection cable in use. Therefore, these values are
intended for reference only.

Panel Cut Dimensions

Create a panel cut and insert the panel into the opening from the front.

A
R C
B

A B C R
HMIGTO6310 301.5 mm (+1, -0 mm) 227.5s mm (+1, -0 mm) 1.6...5 mm 3 mm (0.12 in.)
(11.87 in. [+0.04, -0 in.]) (8.96 in. [+0.04, -0 in.]) (0.06...0.2 in.) maximum
HMIGTO6315 340.5 mm (+1, -0 mm) 266.5 mm (+1, -0 mm)
(13.41 in. [+0.04, -0 in.]) (10.49 in. [+0.04, -0 in.])

NOTE: Before designing the panel cut, refer to Installation (see page 112).

108 EIO0000001133 02/2012

 Specifications

Installation Fastener Dimensions

mm
in. 14
0
1 .39 M6 0.55
0

0.47
12
12
0.47

26
1.02

EIO0000001133 02/2012 109

Specifications

110 EIO0000001133 02/2012

 Magelis GTO
Installation and Wiring
EIO0000001133 02/2012

Installation and Wiring

5
Whats in this Chapter?
This chapter contains the following sections:
Section Topic Page
5.1 Installation 112
5.2 Wiring Principles 118
5.3 SD Card Insertion/Removal 124
5.4 USB Cable Clamp 128

EIO0000001133 02/2012 111

Installation and Wiring

5.1 Installation

Installation Procedures

Introduction
The installation fasteners are required when installing the panel.
Mount the panel in an enclosure that provides a clean, dry, robust and controlled environment. (Magelis
GTO except HMIGTO2315/HMIGTO5315/HMIGTO6315: IP65, Type 1, Type 4X [Indoor Use Only] or
Type 13 Enclosure. HMIGTO2315/HMIGTO5315/HMIGTO6315: IP66k, Type 1, Type 4X [Indoor Use
Only] or Type 13 Enclosure.)

Installation Requirements

Check that the installation wall or cabinets surface is flat, in good condition and has no
jagged edges. Metal reinforcing strips may be attached to the inside of the wall, near the
panel-cut, to increase its rigidity.
Decide on the thickness of the enclosure wall, based on the level of strength required:
1.6...5 mm (0.06...0.2 in.).
Be sure that the surrounding air temperature and the ambient humidity are within their
designated ranges. Surrounding air temperature: 0 to 50 C (32 to 122 F) or 0 to 55 C (32
to 131 F) (see the Environment Specifications for your Magelis GTO); ambient humidity: 10
to 90%RH; wet bulb temperature: maximum 39 C [102 F]. When installing the panel in a
cabinet or enclosure, the surrounding air temperature is the cabinets or enclosures internal
temperature.

Panel Cabinet
Face Interior

Be sure that heat from surrounding equipment does not cause the panel to exceed its
standard operating temperature.
When mounting the panel vertically, ensure that the right side of the unit faces up. In other
words, the power connector should be at the top.

(1)

1 Power connector

112 EIO0000001133 02/2012

 Installation and Wiring

When installing the panel in a slanted position, the panel face should not incline more than
30.

RRUOHVV

When installing the panel in a slanted position with an incline more than 30, the ambient
temperature must not exceed 40 C (104 F). You may need to use forced air cooling (fan,
A/C) to ensure the ambient operating temperature is 40C or less (104 F or less).
For easier maintenance, operation and improved ventilation, install the panel at least
100 mm (3.94 in.) away from adjacent structures and other equipment as shown in the
following illustration:

mm
in.
3.94

3.94
100

100

100 100 100

3.94 3.94 3.94
3.94
3.94

100
100

The holes on the back of the panel (except HMIGTO1300/1310) do not correspond to VESA
75 mm standards. Do not attach the panel to a commercial-type VESA arm.

Panel Mounting Procedure: (except HMIGTO2315/HMIGTO5315/HMIGTO6315)

NOTICE
PANEL UNSTEADY WHEN UNSECURED
Keep panel stabilized in the panel-cut while you are installing or removing the screw fasteners.
Failure to follow these instructions can result in equipment damage.

Step Action
1 Place the panel on a clean and level surface with the display facing downward.
2 Check that the panels gasket is seated securely into the gaskets groove,
which runs around the perimeter of the panel frame.
3 Cut a hole in the installation panel as defined by the Magelis GTOs panel
cutout dimensions.
HMIGTO1300/HMIGTO1310 (see page 48)
HMIGTO2300/HMIGTO2310 (see page 64)
HMIGTO3510/HMIGTO4310 (see page 78)
HMIGTO5310 (see page 93)
HMIGTO6310 (see page 108)
4 Insert the Magelis GTO into the panel-cut.

EIO0000001133 02/2012 113

Installation and Wiring

Step Action
5 Insert the installation fasteners into the panels insertion slots on the top and
bottom sides (left and right sides for the HMIGTO1300/1310). Slide the
fasteners to the back. If the fasteners are not correctly attached, the panel may
shift or fall out.

Installation Panel

Hook

HMIGTO2310

Slots

HMIGTO1310

Slots

6 Insert each of the fasteners shown below. Pull the fastener back until it is flush
with the rear of the attachment hole insert.

7 Use a screwdriver to tighten each fastener screw and secure the panel in
place. The necessary torque is 0.5 Nm (4.4 lb-in).

NOTICE
BROKEN ENCLOSURE
z Do not exert more than 0.5 Nm (4.4 lbin) of torque when tightening the fasteners screws.
z Use on flat surface of a Type 1, Type 4X (Indoor Use Only) or Type 13 Enclosure.
Failure to follow these instructions can result in equipment damage.

114 EIO0000001133 02/2012

 Installation and Wiring

Removal Procedure: (except HMIGTO2315/HMIGTO5315/HMIGTO6315)

Step Action
1 Loosen the installation fasteners (4) from the Magelis GTO.
2 Remove the Magelis GTO slowly from the panel while pressing the projections
on the top.

(1)

(1)

1 Projections
NOTE:
z You could damage the Magelis GTO if you try and remove it without holding
down the projections.
z Watch your fingers so they do not get caught when holding down the
projections.

CAUTION
RISK OF INJURY
Do not drop the Magelis GTO when you remove it from the panel.
z Hold the Magelis GTO in place after removing the fasteners.
z Use both hands.
Failure to follow these instructions can result in injury or equipment damage.

HMIGTO2315/HMIGTO5315/HMIGTO6315 Panel Mounting Procedure

CAUTION
RISK OF INJURY
Do not drop the Magelis GTO when you install or remove it from the panel.
z Hold the Magelis GTO in place after removing the M4 Hex nuts and brackets.
z Use both hands.
Failure to follow these instructions can result in injury or equipment damage.

NOTICE
PANEL UNSTEADY WHEN UNSECURED
Keep panel stabilized in the panel-cut while you are installing or removing the M4 Hex nuts and
brackets.
Failure to follow these instructions can result in equipment damage.

Step Action
1 Place the panel on a clean and level surface with the display facing downward.
2 Confirm that the panels gasket is seated properly on the rear of the panel.

EIO0000001133 02/2012 115

Installation and Wiring

Step Action
3 Cut a hole in the panel as defined by the Magelis GTO panel cutout
dimensions.
HMIGTO2315 (see page 64)
HMIGTO5315 (see page 93)
HMIGTO6315 (see page 108)
4 Insert the Magelis GTO into the panel-cut.

5-2

6-4 6-2

5-4
1
6-1
5-3
6-3

2
3 5-1
4

1 Gasket
2 Panel
3 Brackets
4 M4 Hex Nut
5 Please read Step 5.
6 Please read Step 6.
5 Tighten the four corners of the rear of the panel with the M4 Hex nuts, in the
order shown in the example in Step 4.
Use an M4 box-type screwdriver to tighten each M4 Hex nut and secure the
panel in place. The necessary torque is 0.5 Nm (4.4 lb-in). If the M4 Hex nuts
are not correctly attached, the panel may shift or fall out.
6 Attach the bracket onto the screws in the middle between the M4 Hex nuts in
the order shown in the example in Step 4.
Use an M4 box-type screwdriver to tighten each M4 Hex nut and secure the
panel in place. The necessary torque is 0.5 Nm (4.4 lb-in). If the M4 Hex nuts
are not correctly attached, the panel may shift or fall out.
7 Tighten all the M4 Hex nuts again. The necessary torque is 0.5 Nm (4.4 lb-in).
NOTE: Do not loosen the installation fasteners, marked with red squares
below.

(1)

1 Panel

116 EIO0000001133 02/2012

 Installation and Wiring

NOTICE
BROKEN ENCLOSURE
z Do not exert more than 0.5 Nm (4.4 lbin) of torque when tightening the M4 Hex nuts.
z Use on flat surface of a Type 1, Type 4X (Indoor Use Only) or Type 13 Enclosure.
Failure to follow these instructions can result in equipment damage.

EIO0000001133 02/2012 117

Installation and Wiring

5.2 Wiring Principles

Overview
This section presents the Magelis GTO wiring principles.

Whats in this Section?

This section contains the following topics:
Topic Page
Connecting the Power Cord 119
Connecting the Power Supply 121
Grounding 123

118 EIO0000001133 02/2012

 Installation and Wiring

Connecting the Power Cord

WARNING
EXCESSIVE ELECTROMAGNETIC INTERFERENCE
z When the functional ground (FG) terminal is connected, be sure the wire is grounded. Not grounding
the panel can result in excessive Electromagnetic Interference (EMI). Grounding is required to meet
EMC level immunity.
z Remove power before wiring the panels power terminals.
z The DC model uses only 24 Vdc power. Using any other level of power can damage both the power
supply and the panel.
z Since the panel is not equipped with a power switch, be sure to connect a power switch to the power
supply.
z Be sure to ground the panels FG terminal.
z Replace and secure all elements of the system before applying power to the panel
Failure to follow these instructions can result in death, serious injury, or equipment damage.

NOTE: The shield ground (SG) and FG terminals are connected internally in the panel.

DC Power Cord Preparation

z Make sure the ground wire is either the same or heavier gauge than the power wires.
z Do not use aluminum wires in the power supplys power cord.
z If the ends of the individual wires are not twisted correctly, the wires may create a short circuit.
z Wherever possible, use wires that are 0.75 to 2.5 mm2 (AWG 18 - 13) for the power cord, and twist
the wire ends before attaching the terminals.
z The conductor type is solid or stranded wire.
z Use copper conductors only.
z The temperature rating of field installed conductors: 75 C (167 F) only.

DC Power Supply Connector (Plug) Specifications

HMIGTO1300/1310 / HMIGTO2300/2310/2315 / HMIGTO3510/4310

FG

+
HMIGTO5310/5315 / HMIGTO6310/6315

FG
-
+

Connection Wire
+ 24 Vdc
- 0 Vdc
FG Grounded terminal connected to the panel chassis.

EIO0000001133 02/2012 119

Installation and Wiring

How to connect the DC Power Cord

Step Action
1 Confirm the power cord is not connected to the power supply.
2 Check the rated voltage and remove the DC24V sticker on the DC power
supply connector.
3 Remove 10 mm (0.39 in.) of the vinyl membrane off the ends of the power cord
wires.
4 If using stranded wire, twist the ends. Tinning the ends with solder reduces risk
of fraying and ensures good electrical transfer.
5 Push the Opening button with a small and flat screwdriver to open the desired
pin hole.
6 Insert each pin terminal into its corresponding hole. Release the Opening
button to clamp the pin in place.
HMIGTO1300/1310 / HMIGTO2300/2310/2315 / HMIGTO3510/4310

Opening Button

DC Power Cord (24V)

(0V)

FG

HMIGTO5310/5315 / HMIGTO6310/6315

Opening Button

+ - FG

7 After inserting all three pins, insert the power plug into the power connector on
the panel.

NOTE:
z Do not solder the wire directly to the power receptacle pin.
z To prevent the possibility of a terminal short, use a pin terminal that has an insulating sleeve.
z You can connect the DC power supply connector for HMIGTO1300/1310, HMIGTO2300/2310/2315,
or HMIGTO3510/4310 to HMIGTO5310/5315 or HMIGTO6310/6315 panels. However, the reverse is
not possible. You cannot connect the DC power supply connector for HMIGTO5310/5315 or
HMIGTO6310/6315 to HMIGTO1300/1310, HMIGTO2300/2310/2315, or HMIGTO3510/4310 panels.

120 EIO0000001133 02/2012

 Installation and Wiring

Connecting the Power Supply

Precautions
z You must use a 24 Vdc input unit with a Class 2 power supply.
z To increase the electromagnetic noise resistance, twist the ends of the power cord wires before
connecting them to the power plug.
z The panels power supply cord should not be bundled with or kept close to main circuit lines (high
voltage, high current), or input/output signal lines.
z Connect a lightning surge absorber to handle power surges.
z To reduce electromagnetic noise, make the power cord as short as possible.

WARNING
SHORT CIRCUIT, FIRE, OR UNINTENDED EQUIPMENT OPERATION
Avoid excessive force on the power cable to prevent accidental disconnection:
z Securely attach power cables to the panel or cabinet.
z Use the designated torque to tighten the unit terminal block screws.
z Install and fasten the panel on installation panel or cabinet prior to connecting power supply and
communication lines.
Failure to follow these instructions can result in death, serious injury, or equipment damage.

Power Supply Connections

When supplying power to the panel, separate the input/output and power lines, as shown.

Main Panel
Power Power

Panel
Panel T1
Main Power Panel Power T2
Input/Output
Input/ Unit
Input/Output
Unit Output
Input/Output Power Input/Output
Power Unit
Main Circuit
Operation
Unit

NOTE:
The following shows a lightning surge absorber connection:

Panel
FG
E1 E2

Lightning Surge
Absorber
z Ground the surge absorber (E1) separately from the panel (E2).
z Select a surge absorber that has a maximum circuit voltage greater than that of the peak voltage of
the power supply.
If the supplied voltage exceeds the panel range, connect a constant voltage transformer.


 )*


1 Constant voltage transformer

2 Twisted-pair cord
3 panel

EIO0000001133 02/2012 121

Installation and Wiring

Select a power supply low in noise for between the line and ground. If there is an excess amount of noise,
connect an insulating transformer.


 )*


1 Insulating transformer
2 Twisted-pair cord
3 panel
NOTE: Use constant voltage and insulating transformers with capacities exceeding the Power
Consumption value.

122 EIO0000001133 02/2012

 Installation and Wiring

Grounding

Exclusive Grounding
When supplying power to the panel, separate the input/output and power lines as shown below.
Connect the frame ground (FG) terminal on the power plug to an exclusive ground.

Other
Panel Equipment

Precautions
Electromagnetic Interference (EMI) can be created if the devices are improperly grounded. EMI can
cause loss of communication. Do not use common grounding, except for the authorized configuration
described below. If exclusive grounding is not possible, use a common grounding point.
Correct grounding

Other
Panel Equipment

Incorrect grounding

Other
Panel
Equipment

z Check that the grounding resistance is 100 or less.(1)

z The FG wire should have a cross sectional area greater than 2 mm2 (AWG 14) (1). Create the
connection point as close to the panel as possible, and make the wire as short as possible. When using
a long grounding wire, replace the thin wire with a thicker wire, and place it in a duct.
z FG and SG terminals are internally connected in the panel. When connecting an external device to the
panel using the SG terminal, check that you do not create a short-circuit loop when you set up the
system.
(1) Observe local codes and standards. Ensure the ground connection has a resistance of 100 and that
the ground wire has a cross-section of at least 2 mm2 or AWG 14.

EIO0000001133 02/2012 123

Installation and Wiring

5.3 SD Card Insertion/Removal

Whats in this Section?

This section contains the following topics:
Topic Page
Introduction 125
Inserting the SD Card 126
Removing the SD Card 127
SD Card Data Backup 127

124 EIO0000001133 02/2012

 Installation and Wiring

Introduction

When using the Magelis GTO and a SD Card, observe the following to avoid losing valuable data:
z Since accidental data loss can occur at any time, back up panel screen and SD Card data regularly.
z Before using the SD Card, familiarize yourself with the SD Cards front and rear face orientation, as
well as the position of the SD Card connectors. If the SD Card is not positioned correctly when inserted
into the panel, the cards internal data and the panel could become damaged.

NOTICE
LOSS OF DATA
z Insert the SD Card properly.
z While a SD Card is accessed, do not turn OFF or reset the panel, and do not insert or remove the
SD Card.
z Do not store the SD Card where there is static electricity or electromagnetic waves.
z Do not store the SD Card in direct sunlight, near a heater, or other locations where high temperatures
can occur.
z Do not bend the SD Card.
z Do not drop or strike the SD Card against another object.
z Keep the SD Card dry.
z Do not touch the SD Card connectors.
z Do not disassemble or modify the SD Card.
z Use only SD Cards formatted using FAT or FAT32.
Failure to follow these instructions can result in equipment damage.

EIO0000001133 02/2012 125

Installation and Wiring

Inserting the SD Card

NOTE: As shown in the image below (example on the left-hand side), you can set the Write-Control Tab
to prevent write operations to the SD Card. Push the tab up, as shown in the example on the right-hand
side, to release the lock and enable writing to the SD Card.

Write-Control Tab

Write disabled Write enabled

(Enable to read)

Step Action
1 Pull on the tab and open the SD Card cover.

(1)

1 Tab
2 Insert the SD Card into the SD Card interface, and push until you hear it click.

3 Close the SD Card cover.

126 EIO0000001133 02/2012

 Installation and Wiring

Removing the SD Card

Step Action
1 Make sure the SD Card access LED is off.

(1)

1 SD Card Access LED

2 Push down the tab on the SD Card cover, then pull open the cover.

(1)

1 Tab
3 Push the SD Card once to release, and pull out the card. After removing the
card, close the cover.
NOTE: After using the SD Card, store the SD Card in its case or other safe
location.

SD Card Data Backup

To make your backups, you can either insert the SD Card directly into the SD Card interface on your
computer, or use a commercially available SD Card reader.

EIO0000001133 02/2012 127

Installation and Wiring

5.4 USB Cable Clamp

Overview
This section presents the USB cable clamp.

Whats in this Section?

This section contains the following topics:
Topic Page
USB Cable Clamp for USB (Type A) 129
USB Holder for USB (mini-B) 131

128 EIO0000001133 02/2012

 Installation and Wiring

USB Cable Clamp for USB (Type A)

Introduction
When using a USB device, attaching a USB cable clamp to the USB interface to prevent the USB cable
from being disconnected.

WARNING
RISK OF EXPLOSION IN HAZARDOUS LOCATIONS
z Verify the power, input, and output (I/O) wiring are in accordance with Class I, Division 2 wiring
methods.
z Do not substitute any components that impair compliance to Class I, Division 2.
z Confirm that the USB cable has been fixed with the USB cable clamp before using the USB interface.
z Remove power before attaching or detaching any connectors to or from the panel.
Failure to follow these instructions can result in death, serious injury, or equipment damage.

Attaching the USB Cable Clamp

NOTE: Watch your fingers. The edge of the clip is sharp.

Step Action
1
Mount the clip to the USB mark connector shell so that it overlaps. The
clip matches the 27 to 43.5 mm [1.06 to 1.71 in.] length of the USB connector.

27 . . 43.5 mm
[1.06 . . 1.71 in.]

2 Align the clip and the USB cable connector shell. Adjust the position of the
holes where the clip is attached. To ensure stability, select the clip-hole
position that is closest to the base of the connector shell.

Pass the tie through here.

EIO0000001133 02/2012 129

Installation and Wiring

Step Action
3 As shown, pass the tie through the clip hole. Next, turn the tie and pass it
through the head so that the USB cable can pass through the center of the tie
loop. The clip is now attached to the USB cable.

NOTE:
z Check the direction of the head beforehand. Make sure the USB cable is
through the center of the tie loop and that the tie can pass through the head.
z You can substitute the tie provided with commercially available ties with a
width of 4.8 mm [0.19 in.] and thickness of 1.3 mm [0.05 in.].
4 While pressing the grip on the clip, insert the cable from step 3 all the way into
the USB host interface. Make sure that the clip tab is secured to the USB cable
attached to the Magelis GTO.

Removing the USB Cable

Remove the USB cable while pushing the grip section of the clip.

130 EIO0000001133 02/2012

 Installation and Wiring

USB Holder for USB (mini-B)

Introduction
When using a USB device, you can attach a USB holder to the USB (mini-B) interface to prevent the USB
cable from being disconnected.

WARNING
RISK OF EXPLOSION IN HAZARDOUS LOCATIONS
z Verify the power, input, and output (I/O) wiring are in accordance with Class I, Division 2 wiring
methods.
z Do not substitute any components that impair compliance to Class I, Division 2.
z Confirm that the USB cable has been fixed with the USB holder before using the USB interface.
z Remove power before attaching or detaching any connectors to or from the panel.
Failure to follow these instructions can result in death, serious injury, or equipment damage.

Attaching the USB Holder

Step Action
1 Insert the USB cable into the USB (mini-B) interface.

(1)
1 USB cable
2 Attach the USB holder to fix the USB cable in place. Insert the USB holder into
the USB (mini-B) interface.

(2)
(1)

1 USB holder
2 USB cable

Removing the USB Holder

Remove the USB holder by pressing the tabs from the sides.

(1)

(2)
(1)

1 USB holder
2 USB cable

EIO0000001133 02/2012 131

Installation and Wiring

132 EIO0000001133 02/2012

 Magelis GTO

EIO0000001133 02/2012

Maintenance

6
Overview
This chapter explains how to maintain your panel.

Whats in this Chapter?

This chapter contains the following topics:
Topic Page
Regular Cleaning 134
Replacing the Installation Gasket 135
Periodic Check Points 137
Replacing the Primary Battery 138

EIO0000001133 02/2012 133

Regular Cleaning

Cleaning the display

NOTICE
EQUIPMENT DAMAGE
z Power off the panel before cleaning it.
z Do not use hard or pointed objects to operate the touch panel.
z Do not use paint thinner, organic solvents, or a strong acid compound to clean the unit.
Failure to follow these instructions can result in equipment damage.

When the surface or the frame of the display gets dirty, soak a soft cloth in water with a neutral detergent,
wring the cloth tightly and wipe the display.

134 EIO0000001133 02/2012

Replacing the Installation Gasket

Overview
The installation gasket provides protection against dust and moisture.

NOTICE
GASKET AGING
z Inspect the gasket periodically as required by your operating environment to keep the initial IP level.
z Change the gasket at least once a year, or as soon as scratches or dirt become visible.
Failure to follow these instructions can result in equipment damage.

Installing the Installation Gasket

NOTE: For instructions on how to install the installation gasket when using
HMIGTO2315/HMIGTO5315/HMIGTO6315, see HMIGTO2315/HMIGTO5315/HMIGTO6315 Panel
Mounting Procedure (see page 115).

Stage Description
1 Place the panel on a flat, level surface, with the display face pointing down.
2 Remove the gasket from the panel.
3 Attach the new gasket to the panel. Position the gasket in the installation
groove so that the gasket seam is at the bottom of the panel. First, insert the
gasket into the 4 corners, in the order shown in the image below. Then, insert
the rest of the gasket into the installation groove.
NOTE:
z The center of the panel bezels installation groove is ribbed. Make sure you
insert the gasket all the way in without catching the ribbed sections.
z When using a tool to insert the gasket, make sure the tool does not catch
the rubber gasket and cause a tear.

1 3

Projections

4 2

Gasket

Gasket Seam

Installation
Groove

4 The upper surface of the gasket should protrude approximately 2.0 mm (0.06
in.) from the groove. Check the gasket is inserted correctly before installing the
Magelis GTO into a panel.

2.5
0.1

mm
in.

The gasket must be inserted correctly into the groove for IP65f moisture resistance for the panel. (IP66k
moisture resistance for HMIGTO2315/HMIGTO5315/HMIGTO6315.)

EIO0000001133 02/2012 135

 CAUTION
EQUIPMENT DAMAGE
z Since the gasket is flexible but not elastic, be careful not to stretch it unnecessarily.
z Make sure the gasket seam is not inserted into any of the panel corners.
z Insert the gasket seam in the installation groove.
Failure to follow these instructions can result in injury or equipment damage.

136 EIO0000001133 02/2012

Periodic Check Points

Operation Environment
z Is the operating temperature within the allowable range? Refer to Environmental Specifications
(see Magelis HMI STU 655/855, User Manual).
z Is the operating humidity within the specified range? (10%RH to 90%RH, dry bulb temperature of 39
C (102.2 F) or less)
z Is the operating atmosphere free of corrosive gasses?
When the Magelis GTO is inside a panel, the ambient environment refers to the interior of the panel.

Electrical Specifications
Is the input voltage appropriate?
z 100 Vac to 240 Vac 50/60 Hz
z 19.2 Vdc to 28.8 Vdc

Related Items
z Are all power cords and cables connected properly? Are there any loose cables?
z Are all mounting brackets holding the unit securely?
z Are there scratches or traces of dirt on the installation gasket?

EIO0000001133 02/2012 137

Replacing the Primary Battery

Introduction
The replacement battery HMI ZGBAT (sold separately) for the primary battery in the Magelis GTO is
available from Schneider Electric.
NOTE: The HMIGTO1300/1310 and HMIGTO2300 are not equipped with a primary battery.

DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
z Follow the procedures step by step to replace the battery correctly and safely.
z Before replacing the battery, turn OFF the panels power.
Failure to follow these instructions will result in death or serious injury.

DANGER
EXPLOSION, FIRE, OR CHEMICAL HAZARD
z Use only the replacement battery HMI ZGBAT manufactured by Schneider Electric.
z Do not cause a short circuit.
z Recycle or properly dispose of used batteries.
Failure to follow these instructions will result in death or serious injury.

The primary battery is non-rechargeable, and is used for data backup of memory and the internal clock.
If the primary battery is depleted, the backup data is lost. One month before the primary battery is
completely depleted, an alarm will beep to indicate it is time to replace the primary battery.

NOTICE
LOSS OF DATA
z Replace the battery within one month after an alarm beeps to indicate it is time to replace the battery.
z Complete replacing the battery within ten minutes of shutting down the panel.
z Replace the primary battery regularly, every five years, after you purchase the panel.
Failure to follow these instructions can result in equipment damage.

The primary battery replacement time (within a month after the alarm occurs) is only a guideline. When
backup SRAM data and clock data is lost after the alarm occurs, Schneider Electric does not perform data
recovery/retrieval. Schneider Electric does not accept any responsibility for the loss of data.

Step Action
1 Disconnect the power supply from the Magelis GTO.
2 Touch the housing or ground connection (not the power supply) to discharge
any electrostatic charge from your body.
3 Open the SD Card Interface Cover by pressing its tab. Next, open the
Replacement Battery Insertion Cover by pressing its tab.

(1) (2)

1 SD Card Interface Cover / Tab

2 Replacement Battery Insertion Cover / Tab

138 EIO0000001133 02/2012

 Step Action
4 Remove the primary battery and connector.

(1) (2)

1 Connector
2 Primary battery
5 Attach the new primary battery and connector.

(1) (2)

6 First close the replacement battery cover, then close the SD Card Interface
Cover.
NOTE: Make sure the cables are inserted completely inside the enclosure.
Otherwise, you can damage the cables when you close the cover.
7 Reconnect the power supply to the Magelis GTO.

EIO0000001133 02/2012 139

140 EIO0000001133 02/2012
 Magelis GTO
Index
EIO0000001133 02/2012

Index
B
AC
A K
Accessories, 21 KC marking, 11

B M
battery, 138 maintenance, 133
check points, 137
Maintenance
C Cleaning, 134
caution maintenance accessories, 22
equipment damage, 136 memory, 41, 56, 71, 86, 101
injury, 115, 115
loss of communication, 43, 44, 45, 58, 59, 73, 74,
88, 89, 103, 104 N
CE marking, 11 notice
Certifications and Standards, 11 loss of data, 125
cleaning, 134 panel unsteady when unsecured, 113, 115
clock, 41, 56, 71, 86, 101 loss of data, 138
COM1, 17, 18, 19 overtorque, 114, 117
connecting the power cord, 119
connecting the power supply, 121
O
optional accessories, 22
D
danger
arc flash, 138 P
chemical hazard, 138 parts identification and functions, 25
electric shock, 43, 45, 58, 59, 73, 74, 88, 89, 103, power plug, 119
104, 138
explosion, 138, 138
fire, 138 R
dimensions, 46, 60, 75, 90, 105 replacing the battery, 138
RS-232C, 17, 18
RS-422/RS-485, 18
E RS-485, 19
Ethernet, 19

S
F SD Card, 124
function keys, 41 backup, 127
insertion, 126
SD Card accessories, 22
G serial interface accessories, 21
grounding, 123

I
installation
procedures, 112
installation gasket, 135

EIO0000001133 02/2012 141

Index

specifications
COM, 43, 58, 59, 74, 88, 89, 103, 104
COM1, 42, 57, 58, 72, 73, 87, 88, 102, 103
COM2, 42, 45, 57, 59, 72, 74, 87, 89, 102, 104
display, 40, 55, 70, 85, 100
electrical, 37, 51, 67, 81, 96
environmental, 38, 52, 68, 82, 97
Ethernet, 102
interfaces, 42, 57, 72, 87, 102
SD Card, 57, 72, 102
structural, 39, 53, 69, 83, 98
USB, 42, 42, 57, 57, 72, 72, 87, 87, 87, 102

T
touch panel, 41, 56, 71, 86, 101

U
USB
cable clamp for USB Type A, 129
holder mini-B, 131
USB interface accessories, 22
USB mini-B, 20
USB Type A, 20

W
warning
electromagnetic interference, 119
expertise in designing and programming control
systems, 7
explosion, 129, 131
fire, 121
short circuit, 121
unintended equipment operation, 7, 121

142 EIO0000001133 02/2012