Code No:117AU Set No.
1
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD
IV B.Tech. I Sem., I Mid-Term Examinations, September-2017
AUTOMOTIVE CHASSIS AND SUSPENSION
Objective Exam
Name: ______________________________ Hall Ticket No. A
Answer All Questions. All Questions Carry Equal Marks. Time: 20 Min. Marks: 10.
I. Choose the correct alternative:
1. The effect of the weight of the body on the side members of the frame will be. [ ]
a) inclined bending b) horizontal bending c) vertical bending d) twisting
2. The member of supporting points needed to mount engine clutch gear box on the chassis frame is
[ ]
a) four b)three c)two d)one
3. The mounting used between engine gear box unit and frame are made of [ ]
a) stainless steel b) brass c) rubber d) wood
4. Cooling is more effective , if the cooling system is placed on the frame at [ ]
a) middle b) rear c)front d)middle right
5. Tubeless tires cannot be used on the following type of wheel [ ]
a) wire wheel b) dise wheel c) alloy wheel d) compressing wheel
6. shock absorbers in the two-wheelers are used to [ ]
a) increase the energy b)decrease the energy c) adsorb the energy d)dissipate the energy
7. The leaf spring eye of the heavy vehicle is generally bushed with [ ]
a) stainless steel b) phosphor bronze c) cast iron d) High speed steel
8. The steering ratio for heavy vehicles is [ ]
a)8:1 b)12:1 c) 20:1 d)35:1
9. The operation of brakes will be carried out in cars [ ]
a) hydraulically b) high pressure air c)mechanically d) vacuum
10. The component used on the wheel cylinder to seal , the brake fluid is [ ]
a) dust cover b) piston c) cup d) spring
Cont..2
Code No: 117AU :2: Set No. 1
II Fill in the Blanks:
11. Chassis is also known as ___________________________ .
12. To allow trapped water to run out, we have to provide number of __________________ .
13. Zine coating on steel parts is provided to avoid rusting is known as ___________________________.
14. In feline , the present I.C. engine power unit on Automobiles will be replaced by __________________ .
15. O The wheels wear, if over inflated at __________ .
16. Rubber springs have excellent property of vibration _____________________ .
17. The top surface of each leaf of the spring _______________________ to improve fatigue starength and
life.
18. The sum of the cornering force and slip angle is called __________________ .
19. When the top of wheel slants outward, the slant angle of wheel with vertical is called________ .
20. The minimum allowable limit of hand brake efficiency for any vehicle is ____________________ .
-oOo-
Code No:117AU Set No. 2
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD
IV B.Tech. I Sem., I Mid-Term Examinations, September-2017
AUTOMOTIVE CHASSIS AND SUSPENSION
Objective Exam
Name: ______________________________ Hall Ticket No. A
Answer All Questions. All Questions Carry Equal Marks. Time: 20 Min. Marks: 10.
I. Choose the correct alternative:
1. Cooling is more effective , if the cooling system is placed on the frame at [ ]
a) middle b) rear c)front d)middle right
2. Tubeless tires cannot be used on the following type of wheel [ ]
a) wire wheel b) dise wheel c) alloy wheel d) compressing wheel
3. shock absorbers in the two-wheelers are used to [ ]
a) increase the energy b)decrease the energy c) adsorb the energy d)dissipate the energy
4. The leaf spring eye of the heavy vehicle is generally bushed with [ ]
a) stainless steel b) phosphor bronze c) cast iron d) High speed steel
5. The steering ratio for heavy vehicles is [ ]
a)8:1 b)12:1 c) 20:1 d)35:1
6. The operation of brakes will be carried out in cars [ ]
a) hydraulically b) high pressure air c)mechanically d) vacuum
7. The component used on the wheel cylinder to seal , the brake fluid is [ ]
a) dust cover b) piston c) cup d) spring
8. The effect of the weight of the body on the side members of the frame will be. [ ]
a) inclined bending b) horizontal bending c) vertical bending d) twisting
9. The member of supporting points needed to mount engine clutch gear box on the chassis frame is
[ ]
a) four b)three c)two d)one
10. The mounting used between engine gear box unit and frame are made of [ ]
a) stainless steel b) brass c) rubber d) wood
Cont..2
Code No: 117AU :2: Set No. 2
II Fill in the Blanks:
11. In feline , the present I.C. engine power unit on Automobiles will be replaced by __________________ .
12. O The wheels wear, if over inflated at __________ .
13. Rubber springs have excellent property of vibration _____________________ .
14. The top surface of each leaf of the spring _______________________ to improve fatigue starength and
life.
15. The sum of the cornering force and slip angle is called __________________ .
16. When the top of wheel slants outward, the slant angle of wheel with vertical is called________ .
17. The minimum allowable limit of hand brake efficiency for any vehicle is ____________________ .
18. Chassis is also known as ___________________________ .
19. To allow trapped water to run out, we have to provide number of __________________ .
20. Zine coating on steel parts is provided to avoid rusting is known as ___________________________.
-oOo-
Code No:117AU Set No. 3
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD
IV B.Tech. I Sem., I Mid-Term Examinations, September-2017
AUTOMOTIVE CHASSIS AND SUSPENSION
Objective Exam
Name: ______________________________ Hall Ticket No. A
Answer All Questions. All Questions Carry Equal Marks. Time: 20 Min. Marks: 10.
I. Choose the correct alternative:
1. shock absorbers in the two-wheelers are used to [ ]
a) increase the energy b)decrease the energy c) adsorb the energy d)dissipate the energy
2. The leaf spring eye of the heavy vehicle is generally bushed with [ ]
a) stainless steel b) phosphor bronze c) cast iron d) High speed steel
3. The steering ratio for heavy vehicles is [ ]
a)8:1 b)12:1 c) 20:1 d)35:1
4. The operation of brakes will be carried out in cars [ ]
a) hydraulically b) high pressure air c)mechanically d) vacuum
5. The component used on the wheel cylinder to seal , the brake fluid is [ ]
a) dust cover b) piston c) cup d) spring
6. The effect of the weight of the body on the side members of the frame will be. [ ]
a) inclined bending b) horizontal bending c) vertical bending d) twisting
7. The member of supporting points needed to mount engine clutch gear box on the chassis frame is
[ ]
a) four b)three c)two d)one
8. The mounting used between engine gear box unit and frame are made of [ ]
a) stainless steel b) brass c) rubber d) wood
9. Cooling is more effective , if the cooling system is placed on the frame at [ ]
a) middle b) rear c)front d)middle right
10. Tubeless tires cannot be used on the following type of wheel [ ]
a) wire wheel b) dise wheel c) alloy wheel d) compressing wheel
Cont..2
Code No: 117AU :2: Set No. 3
II Fill in the Blanks:
11. Rubber springs have excellent property of vibration _____________________ .
12. The top surface of each leaf of the spring _______________________ to improve fatigue starength and
life.
13. The sum of the cornering force and slip angle is called __________________ .
14. When the top of wheel slants outward, the slant angle of wheel with vertical is called________ .
15. The minimum allowable limit of hand brake efficiency for any vehicle is ____________________ .
16. Chassis is also known as ___________________________ .
17. To allow trapped water to run out, we have to provide number of __________________ .
18. Zine coating on steel parts is provided to avoid rusting is known as ___________________________.
19. In feline , the present I.C. engine power unit on Automobiles will be replaced by __________________ .
20. O The wheels wear, if over inflated at __________ .
-oOo-
Code No:117AU Set No. 4
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD
IV B.Tech. I Sem., I Mid-Term Examinations, September-2017
AUTOMOTIVE CHASSIS AND SUSPENSION
Objective Exam
Name: ______________________________ Hall Ticket No. A
Answer All Questions. All Questions Carry Equal Marks. Time: 20 Min. Marks: 10.
I. Choose the correct alternative:
1. The steering ratio for heavy vehicles is [ ]
a)8:1 b)12:1 c) 20:1 d)35:1
2. The operation of brakes will be carried out in cars [ ]
a) hydraulically b) high pressure air c)mechanically d) vacuum
3. The component used on the wheel cylinder to seal , the brake fluid is [ ]
a) dust cover b) piston c) cup d) spring
4. The effect of the weight of the body on the side members of the frame will be. [ ]
a) inclined bending b) horizontal bending c) vertical bending d) twisting
5. The member of supporting points needed to mount engine clutch gear box on the chassis frame is
[ ]
a) four b)three c)two d)one
6. The mounting used between engine gear box unit and frame are made of [ ]
a) stainless steel b) brass c) rubber d) wood
7. Cooling is more effective , if the cooling system is placed on the frame at [ ]
a) middle b) rear c)front d)middle right
8. Tubeless tires cannot be used on the following type of wheel [ ]
a) wire wheel b) dise wheel c) alloy wheel d) compressing wheel
9. shock absorbers in the two-wheelers are used to [ ]
a) increase the energy b)decrease the energy c) adsorb the energy d)dissipate the energy
10. The leaf spring eye of the heavy vehicle is generally bushed with [ ]
a) stainless steel b) phosphor bronze c) cast iron d) High speed steel
Cont..2
Code No: 117AU :2: Set No. 4
II Fill in the Blanks:
11. The sum of the cornering force and slip angle is called __________________ .
12. When the top of wheel slants outward, the slant angle of wheel with vertical is called________ .
13. The minimum allowable limit of hand brake efficiency for any vehicle is ____________________ .
14. Chassis is also known as ___________________________ .
15. To allow trapped water to run out, we have to provide number of __________________ .
16. Zine coating on steel parts is provided to avoid rusting is known as ___________________________.
17. In feline , the present I.C. engine power unit on Automobiles will be replaced by __________________ .
18. O The wheels wear, if over inflated at __________ .
19. Rubber springs have excellent property of vibration _____________________ .
20. The top surface of each leaf of the spring _______________________ to improve fatigue starength and
life.
-oOo-
