Scribd
Upload
218 views1 page

Requirement For Butt Welded Fittings Astm A403 Gr. Wp316L/316L-Wx

This specification covers the requirements for butt welded fittings to be used in manufacturing piping spools according to ASME B31.3 for Class 1SD0P piping. The fittings must be made of ASTM A403 Grade WP316L/316L-WX stainless steel, have butt weld ends, and a size range of 8-30 inches. The material must meet multiple standards and specifications and undergo testing and inspection to ensure quality. Only after receiving approval can the material be dispatched.

Uploaded by

naveen_86
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
218 views1 page

Requirement For Butt Welded Fittings Astm A403 Gr. Wp316L/316L-Wx

This specification covers the requirements for butt welded fittings to be used in manufacturing piping spools according to ASME B31.3 for Class 1SD0P piping. The fittings must be made of ASTM A403 Grade WP316L/316L-WX stainless steel, have butt weld ends, and a size range of 8-30 inches. The material must meet multiple standards and specifications and undergo testing and inspection to ensure quality. Only after receiving approval can the material be dispatched.

Uploaded by

naveen_86
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 1

INQ_610

REV. :A
SPECIFICATION
PAGE : 1 OF 1

DOC NO. INQ_610


REQUIREMENT FOR BUTT WELDED FITTINGS ASTM A403 GR. WP316L/316L-WX REV

THIS SPECIFICATION COVERS THE REQUIREMENTS OF BUTT WELD FITTINGS TO BE USED IN MANUFACTURING OF
1
PIPING SPOOLS AS PER ASME B31.3. PIPING CLASS 1SD0P.
MATERIAL SHALL BE AS FOLLOWS:
2 SIZE : 8 - 30
DESIGN: BUTT WELD ENDS
MATERIAL: ASTM A403 GR. WP316L/316L-WX
PIPE SHALL BE MANUFACTURED FROM ELECTRIC FUSION WELDING WITH 100% RX.
STANDARD OF DIMENTIONS : ASME B16.9
BEVEL END AS PER ASME B16.25
MATERIAL SHALL BE SUPPLIED IN NORMALIZED CONDITION.
CARBON EQUIVALENT SHALL BE LIMITED TO 0.42%. (BY LONG FORMULA).
MATERIAL SHALL CONFORM TO ASTM A403/A403M GR. WP316L/316-S, INCLUDING ASTM A960
SUPPLEMENTARY REQUIREMENTS S50 PRODUCT ANALYSIS S51 TENSION TEST AND S57 HARDNESS
TEST.
ALL THE TEST RESULTS SHALL BE REPORTED IN THE MATERIAL TEST CERTIFICATES PER EN10204 TYPE
3.1.
FITTING SHALL BE SUBJECTED TO INTERGRANULAR CORROSION TEST AS PER ASTM A262
PRACTICE E.
THE FITTINGS ENDS MUST BE CAPPED DURING SHIPPING.
MATERIAL SHALL COMPLY WITH THE FOLLOWING SAUDI ARAMCO SPECIFICATIONS;
SAES-L-100 20 FEB 2012
02-SAMSS-005 20 FEBRUARY 2012
IR-175-023400
ASME B16.9 LATEST EDITION
ASME B16.25 LATEST EDITION
VENDOR TO PROVIDE COPIES OF MTC AND OTHER DOCUMENTS REQUIRED PRIOR TO DESPATCH OF MATERIAL.
3
ONLY AFTER RECEIVING THE APPROVAL MATERIAL SHALL BE DESPATCH.

4 GASKET SURFACE SHALL BE PROTECTED DURING SHIPPING.

VENDOR TO STRICTLY COMPLY WITH THE REQUIREMENTS., ANY CONFLICT IN THE DIOCUMENTS / SPECS SHALL
8
BE BROUGHT TO NATCO NOTICE FOR IMMEDIATE CLARIFICATION.
A
DATE 10.04.2016
BY NAVEEN
CHK SETH

You might also like