Scribd
Upload
410 views

Create A Valve

MODELLING GLOBE VALVE. CreateSection. VALVES CreateCategoryFor components VGL300# If there's something writed, first clear all. Fill as indicated. Now we'll go to create the Ppoints.

Uploaded by

Bruno Assis
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
410 views

Create A Valve

MODELLING GLOBE VALVE. CreateSection. VALVES CreateCategoryFor components VGL300# If there's something writed, first clear all. Fill as indicated. Now we'll go to create the Ppoints.

Uploaded by

Bruno Assis
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 15

MODELLING GLOBE VALVE

Nom A B C D E F G H L
Size
100 480 250 32 875 140 675 50 360 30
150 520 318 37 900 175 700 55 370 34
200 560 381 42 925 200 725 60 380 38

GLOBE VALVE 300#

PARA 1=NOM SIZE DN 100


PARA 2=CONNECTION FBB
PARA 3= A (LENGTH) 480
PARA 4= B (FLG DIAM) 254
PARA 5=C (FLG THK) 32
PARA 6=D (HEIGTH) 875
Paragon<Pipework

Create<Section.
VALVES
Create<Category<For components
VGL300#

If there’s something writed , first clear all.


Fill as indicated.

First fill the name of Ppoint Set :


/VGL300#PS

Then fill the name of Geom Set:


/VGL300#GS

Fill the “parameter Description” as indicated above and click in “insert after” everytime , at the end
the description appear under “Description”

APPLY<DISMISS
Create<component

Fill as indicated below

APPLY<DISMISS

In the Members form select the SCOM just created.


Display<components
Now we’ll go to create the Ppoints.

P1

If there’s an operation it must be between brackets

APPLY
Now the first Ppoint is created
Now the P2
Now the P3 for round around the axis

PAXI= X because must be perpendicolar


PDIS=0 matching with origin or P0
Nor Connection Type neither Bore

If it’s necessari to modify a Ppoint , select the PTAX and select Modify instead of Create

Now it’s necessariy to define the Geometry

Select the GMSE /VGL300#GS

Cylinder (LCYL)
APPLY

We’ve created the flangie

Now the other flangie

Now we’ll create the body of valve.

The cilinder it’s created from the P1


Now it’s created the bottom of valve
Now a SNOUT

Now a cylinder

Now the handwheel

For create the hadnwheel it’s necessary to create a new Ppoint (P4),

Select the PTSE /VGL300#PS


Now a new Ppoint ( P5 )
Now the hadwheel
Go to the GMSE

Again the other axis

For the circles of the hadwheel use 2 circular torus.


For this reason it’s necessary to create 2 new Ppoints (P6 and P7), looking X
Navigate to PTSE and create two cartesian points .
Now P7

Now the geometry


Navigate to GMSE

now the other half


Now the obstruction.

Select Obstruction volume.

--------------------------------------------------------------------------------------------------------------------

Now create the Description text:


Navigate to CATE
Create<detail text
Fill:

If all is OK then SAVEWORK


Now for create the other components SCOM write the macro in a Text editor:
----------------------------------------------------------------------------------------------------
NEW SCOM /VGL300#150 COPY /VGL300#100 PARA 150 FBB 520 318 37 900
NEW SCOM /VGL300#200 COPY /VGL300#100 PARA 200 FBB 560 381 42 925

Save it as VGL300.txt
Select the last SCOM created and run the macro.
Display<comand line
$m /path

Don’t forget to assign the BLTARRAY for every SCOM if you want to use the new bolting
method, for this purpose see the manuals and indications of the forum.

------------------------------------------------------------------------------------------------------------------------
DISCLAIMER:
This manual is for information purposes and a contribution for PDMS forum only.
It’s recommended to take a training first.
Use of this manual at your own risk.
In no event shall the writer be liable for any direct, indirect, incidental, special, exemplary, or
consequential damages.
The software utilizated for the snapshots is a register copy of PDMS 11.6sp4, none parts of
Copyrighted documents have been taken.

Written by Juan M: Gutierrez Valderrama.


Leon-Spain

You might also like