03

Kerys
Navigation
(operator access)

Module KERYS ENG

01/09/2014 Module KERYS ENG
 SUMMARY

1- Operation menu
2- Fault finding menu
3- Archiving and metering menu

Service formation AD
01/09/2014 Module KERYS ENG
Menus - Flowchart

01/09/2014 Module KERYS ENG 3

Main page

01/09/2014 Module KERYS ENG 4

 System menu 61 and 62

Regional parameters
Language choice
Direct link if you click on the date and
time (top left)
Logo main page choice

Identification application
Display identification numbers
Important when using TELEKERYS

01/09/2014 Module KERYS ENG

5
 System Software version menu (63)

Software versions
Important screen to debug version software problems
Be careful with software/hardware compatibilities

01/09/2014 Module KERYS ENG

6
Reminders: IHM fascias

3 KINDS OF Fascias

01/09/2014 Module KERYS ENG 7

Menus - Flowchart

01/09/2014 Module KERYS ENG 8

Overview - menus

01/09/2014 Module KERYS ENG 9

Overview - menus

The 6 menus (on standard basis) are:

1- OPERATION
2- FAULT FINDING
3- ARCHIVING AND METERING
4- MAINTENANCE
5- CONFIGURATION
6- FACTORY
(7- RENTAL SUMMARY) Additional menu for rental application
01/09/2014 Module KERYS ENG 10
01/09/2014 Module KERYS ENG 11
 SUMMARY

1- Operation
2- Fault finding
3- Archiving and metering

Service formation AD
01/09/2014 Module KERYS ENG
Operation menu - flowchart

01/09/2014 Module KERYS ENG 13

Operation menu (1)

01/09/2014 Module KERYS ENG 14

Operation menu (11) generator

Digital display

+ SPEED/- SPEED + VOLTAGE/- VOLTAGE

01/09/2014 Module KERYS ENG 15

Operation menu (11) PC
Function keys (menu 12)
Press on GLOBAL OPERATION is like changing the wattmetric
management parameter to WITHOUT .

GLOBAL
OPERATION

01/09/2014 Module KERYS ENG 17

 Synchro column (menu 12)

Only
manual mode

With the X179 Reg module, the

PIDs activated are shown in
green (accuracy is 1/10%).

01/09/2014 Module KERYS ENG 18

Synchro column display

01/09/2014 Module KERYS ENG 19

Central unit measure summary (menu 14)

01/09/2014 Module KERYS ENG 20

Central unit measure summary (menu 14)

01/09/2014 Module KERYS ENG 21

Electrical measurements Generator (151)

01/09/2014 Module KERYS ENG 22

Electrical measurements busbar or Mains

Note: another scrolling key is displayed when more than 1 mains are selected
(from firmware 1.05)
01/09/2014 Module KERYS ENG 23
Mechanical measurements menu (153)

01/09/2014 Module KERYS ENG 24

Mechanical measurements (153)

Engine error code

SPN xxxx FMI xxxx

01/09/2014 Module KERYS ENG 25

Exemple of faults

01/09/2014 Module KERYS ENG 26

 Harmonics measurement (154)
From the generator and the Mains

FUNDAMENTAL
f = 50hz, amplitude 110V
+
Harmonic RANK 3
f = 50hz, amplitude 10V
+
Harmonic RANK 5
f = 250hz, amplitude 10V
+
Harmonic RANK 7
100 V f = 350hz, amplitude 10V
Amplitude

=
10V 10V 10V OUPUT SIGNAL
Frequency
50Hz 150Hz 250Hz 350Hz
FOURIER representation Temporal representation

01/09/2014 Module KERYS ENG

27
 Operation- Electrical measurements (156)

Same Phase sequence

A B C

C B A

Green : phase sensing is clockwise

Red: Phase sensing is anticlockwise
Black: no voltage

01/09/2014 Module KERYS ENG

28
Mesures personnalise Ana (fentre 157)

Si ente Ana personnalis configure

 Operation Faults and alarms (menu 16)

01/09/2014 Module KERYS ENG

30
 User Adjustment (171)

Set points and production settings

Activation of boxes by KERYS

variables

Green boxes mean variables

used by the KERYS system

U(V) and the Un BUS are very

important and must be set up
properly.

01/09/2014 Module KERYS ENG

31
 Ex Consigne
U GE and Busbar= 400v
KW mains= 0
Cos Phi GE = 0.80 L

Only withX179

Activate the box by

variables

01/09/2014 32
Module KERYS ENG
 User adjustment - Output Threshold (172)

When the KW in % is
reached, the relevant
boxes become green

CPU: power plant

Total KW of the multiple
generators

%Kw reached based on the nominal KW generator and/or nominal KW power plant

01/09/2014 Module KERYS ENG

33
User adjustment Wattmetric control (173)

Activation of the Wattmetric control

Setting of running timers

Selection of priorities of generators in

the powerplant ( You only need to
change the priority sequence on one
KERYS the sequence will be
autamatically transferred to the other
KERYS which are in communication)

The Number seven is the first one to shutdown

The priorities for all the generators is done from
one kerys.
Priorities of the generators to shutdown
based on the load

01/09/2014 Module KERYS ENG

34
 Only for the
configurations A632, 633,
and 635

This sub menu is displayed

only if 2 fuel pompes or 2
starter motors or selection
permanent/temporary sync
with mains activated

Module KERYS ENG

01/09/2014 35
 Wattmetric management activated

WITH
The wattmetric management starts after 10 mins when
600 the 5 generators are in parallel together.

60 60
Generator Ramp up time Generator Ramp down time

This parameter limits the numbers of generators to start when

mains failure or remote start order detected if 5 is the number of
Number of generator to start in addition of generators you can put less than 5.
the minimun number of generator

Module KERYS ENG

 Exemple of priorities

Change the priority on one generator

the other generators will have their
priorities changed accordingly while they
are running.
Since the X179, there is no need to press
on backup to perform .
Module KERYS ENG
Module KERYS ENG
User adjustment Wattmetric control (173)

Threshold 8GS => 7GS

01/09/2014 Module KERYS ENG

39
User parameters (174)

Off Load Test: 10 mins

Time before start up when mains failure

Time before stop the generator when mains healthy

If mains fails to syn the generator
without : the generator supplies the load
With changeover: for the mains to supply the load
If generator fails to syn with the mains
without : the mains supplies the load
With : changeover for the generator to supply the load

Exemple with 2 mains (power means mains)

01/09/2014 Module KERYS ENG 40

 User parameters (175)
CRF= Shor t term sync (10 secs) with Mains
CRP: permanent sync with Mains. A641

60 60
Ramp up Ramp down

Related to starter motors

Ramps:
Consider 60 secs/ 1MW when synchronize with the UTILITY
01/09/2014 Module KERYS ENG 41
 SUMMARY

1- Operation
2- Fault finding
3- Archiving and metering

Service formation AD
01/09/2014 Module KERYS ENG
 Fault Finding Menu (2)

01/09/2014 Module KERYS ENG

43
Mapping Variables KERYS

01/09/2014 Module KERYS ENG 44

Address 1 0 x x
BUS CAN1 OUTPUT @module Chanel N

Address 1 1 x x
BUS CAN1 INPUT @module Chanel N

01/09/2014 Module KERYS ENG 45

Mapping Variables KERYS
Address 3 0 x x
BASE OUTPUT @module Chanel N

Address 3 1 x x
BASE INPUT @module Chanel N

01/09/2014 Module KERYS ENG 47

Mapping Variables KERYS
Mapping Variables KERYS
Fault Finding O/I variables (menus 21,22, 23)

Menu 21 Menu 22 Menu 23

Digital I/O Analog I/O REG & PRO I/O

Display digital values Display analog values Display regulation and
40XX to 42XX Input variables 50XX to 52XX Input variables of the protection values
(Auto mode, LED test, + speed, close ANA module
Mains breaker) (temperature, number of generator in Display measurements, statuses,
43XX to 44XX Input operator the powerplant, priority) thresholds
45XX to 49XX Internal variables 53XX to 55XX Input operator Utilization of variable tables of
(Run order, Top synchro, synchro ) 56XX to 58XX Internal inputs
each module.
(temperature, voltage, frequency)
4AXX and ADXX to AFXX Available
59XX to 5FXX Available

01/09/2014 Module KERYS ENG

50
 Fault Finding Curves (menu 24)

Graphics

from 4 variables

evolution of these 4
variables

Only with IHM Tactile

01/09/2014 Module KERYS ENG

51
 Fault Finding Electrical faults (menu 25)

Electrical Faults function

To visualize value of a
data in a short scale of
time

Dont reset fault and alarm

to visualize the screen

01/09/2014 Module KERYS ENG

52
 Help Menu (menu 26)

Help function

To have a short definition

of anomalies (alarms,
faults )

Possibility to key words to find out the fault number 6xxx

01/09/2014 Module KERYS ENG

53
 Regulation module display (menu 27)

Reg module display function

(from Version 1.05b)

To know the % of regulation

output (speed and voltage)

To know if the AVR and ASR have

good setting (if too much
correction, might be an error in
AVR and ASR set points)

To know the status of the system

(syncro)

Only if the regulation module is selected

01/09/2014 Module KERYS ENG

54
Visualisation TOR (menu 28)
 SUMMARY

1- Operation
2- Fault finding
3- Archiving and metering

Service formation AD
01/09/2014 Module KERYS ENG
Architecture

01/09/2014 Module KERYS ENG 57

Event archive (menu 31)

Kind of event logs ( FIFO) where faults, alarms and statuses are
listed par date and hour to understand the history of events during
failures.
512 messages
01/09/2014 Module KERYS ENG 58
Electrical Archives (menu 32)
1- Select the parameters that you want to record,
2- Activate the reccording by adding the following input equation: 4188 = 450C

01/09/2014 Module KERYS ENG 59

Mechanical archives (menu 33)
1- Select the mechanical parameters that you want to record,
2- Activate the reccording by adding the following input equation: 4189 = 450C

01/09/2014 Module KERYS ENG 60

 Electrical & mechanical data recording

Measurements to be taken every 60 secs (sampling time)

To give you 1819 measures

=> 30 hours
Variable 4188: Electrical archives and measurements
Variable 4189: Mechanical archives and measurements

To activate the recording, enter the 2 following additionnal equations:

4188= 450C
4189= 450C
Go to CONFIGURATION/APPLICATION/EQUATION/DIGITAL INPUT

450C being the variable for generator running

01/09/2014 Module KERYS ENG 61

Electrical & mechanical data recording

01/09/2014 Module KERYS ENG 62

Event metering (menu 34)
Counter of apparition of anomalies

Example:
7200 is the anormaly variable
number
7300 is the variable where is
stored the number of apparition

Its possible to use this

values to do comparison in the
Equation menu.

To count the changes of status of the binary variables

01/09/2014 Module KERYS ENG 63

Mechanical metering (menu 35)

Possibility to change the

hours and mins if access
code level 3.
Interresting when you
need to replace the IHM.

01/09/2014 Module KERYS ENG 64

Electrical metering (Menu 36)

Display of production of active and reactive powers

Possibility to reset values with an access code

01/09/2014 Module KERYS ENG 65

 Thank you for your attention!

Service formation AD
01/09/2014 Module KERYS ENG