Scribd
Upload
3K views1 page

RT IQI Selection

The document contains 3 tables providing information about wire types and sizes used for industrial radiography quality control. Table 1-a lists wire diameters and numbers for 3 common DIN wire pack designs. Table 1-b lists wire diameters and identities for 4 sets of ASME wire types. Table 3 shows which DIN and ASME wire numbers should be selected as source and film side wires based on nominal material thickness being inspected.

Uploaded by

Vipin Peter
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
3K views1 page

RT IQI Selection

The document contains 3 tables providing information about wire types and sizes used for industrial radiography quality control. Table 1-a lists wire diameters and numbers for 3 common DIN wire pack designs. Table 1-b lists wire diameters and identities for 4 sets of ASME wire types. Table 3 shows which DIN and ASME wire numbers should be selected as source and film side wires based on nominal material thickness being inspected.

Uploaded by

Vipin Peter
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 1

Table 1-a DIN Wire Type IQI

DIN Pack Wire Diameter (mm)


Designation Corresponding Wire Number
3.20 2.50 2.00 1.60 1.25 1.00 0.80
1 FE DIN
1 2 3 4 5 6 7
1.00 0.80 0.63 0.50 0.40 0.32 0.25
6 FE DIN
6 7 8 9 10 11 12
0.40 0.32 0.25 0.20 0.16 0.125 0.1
10 FE DIN
10 11 12 13 14 15 16

Table 1-b ASME Wire Type IQI


Set A Set B Set C Set D
Diameter(mm) Identity Diameter(mm) Identity Diameter(mm) Identity Diameter(mm) Identity
0.08 1 0.25 6 0.81 11 2.54 16
0.10 2 0.33 7 1.02 12 3.20 17
0.13 3 0.41 8 1.27 13 4.06 18
0.16 4 0.51 9 1.60 14 5.08 19
0.20 5 0.64 10 2.03 15 6.35 20
0.25 6 0.81 11 2.54 16 8.13 21

Table 3. IQI selection


Unless otherwise stated in the Scope of Work,
IQI shall be selected as shown in the following columns.
DIN IQI ASTM IQI
Nominal Single-Wall Material Thickness
Source Side Film Side Source Side Film Side
inch mm Wire No. Wire No. Wire No. Wire No.

Up to 0.25, incl. Up to 6, incl. 13 14 5 4

Over 0.25 through 0.375 6 through 10 12 13 6 5

Over 0.375 through 0.50 10 through l2 11 12 7 6

Over 0.50 through 0.75 l2 through 18 10 11 8 7

Over 0.75 through 1.00 18 through 25 9 10 9 8

Over 1.00 through 1.50 25 through 40 8 9 10 9

Over 1.50 through 2.00 40 through 50 7 8 11 10

Over 2.00 through 2.50 50 through 60 6 7 12 11

Over 2.50 through 4.00 60 through 100 5 6 13 12

Over 4.00 through 6.00 100 through 150 4 5 14 13

Over 6.00 through 8.00 150 through 200 2 4 16 14

Over 8.00 through 10.00 200 through 250 1 2 17 16

You might also like