Scribd
Upload
499 views2 pages

Toriconical Head 87 Psi

The document provides calculations for a toriconical head according to the ASME Section VIII Division 1 code. It includes design data for pressure, temperature, materials and dimensions. It then calculates thicknesses for the conical and spherical sections and determines the minimum required thickness. It performs calculations to determine the maximum allowable working pressure at hot/corroded and cold/new conditions. It also includes calculations for reinforcement of the small end junction.

Uploaded by

Fabio Augusto Hincapie Henao
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
499 views2 pages

Toriconical Head 87 Psi

The document provides calculations for a toriconical head according to the ASME Section VIII Division 1 code. It includes design data for pressure, temperature, materials and dimensions. It then calculates thicknesses for the conical and spherical sections and determines the minimum required thickness. It performs calculations to determine the maximum allowable working pressure at hot/corroded and cold/new conditions. It also includes calculations for reinforcement of the small end junction.

Uploaded by

Fabio Augusto Hincapie Henao
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

ASME CODE CALCULATIONS SECTION VIII DIVISION 1 2004 EDITION

2006 ADDENDA

TORICONICAL HEAD CALCULATIONS JOB No. 101241

1.0 Design Data

Design Pressure P= 87,00 psi UG-22


Design Temperature T= T= 300,00 °F UG-20
Inside Diameter ID= 23,722 inch
Corrosion Allowance C= 0 inch UG-25
Head Material SA 36
Allowable Stress at Design Temp. S= 16600 psi Sect IID,1A
Allowable Stress at Ambient Temp. S= 16600 psi Sect IID,1A
Head Efficiency E= E= 0,65 UW-12
Corroded Diameter D= 23,722 inch
Half Apex Angle a= 35,00 °
Knuckle Radius r= 9,840 inch
Minor Diameter Dm= 4,250 inch

2.1 Conical Section Thickness Calculations

Di=D-2(r+C)cos a Di= 20,1626 inch


t=PDi/[2cos a(SE-0.6P)] t= 0,0997 inch
treq=t + C treq= 0,0997 inch

2.2 Spherical Section Thickness Calculations

L=Di/(2cos a) L= 12,307 inch


M=1/4[3+Sqrt[L/(r+C)] M= 1,030
t=PLM/(2SE-0.2P) t= 0,051 inch
treq=t + C treq= 0,0511 inch

2.3 Head Thickness Calculations

treq=Greater of the above treq= 0,0997 inch


tactual= 0,1000 inch
tnom= 0,1000 inch
rmin=3tnom rmin= 0,3000 inch

3.1 MAWP Hot and Corroded Calculations

P=2SEtcos a/(Di+1.2tcos a) P= 87,25 psi


P=2SEt/(LM+0.2t) P= 170,04 psi
P= Lower of the above P= 87,25 psi
MAWP = P-H MAWP= 87,25 psi

3.2 MAWP Cold and New Calculations

P=2SEtcos a/(Di+1.2tcos a) P= 87,25 psi


P=2SEt/(LM+0.2t) P= 222,01 psi
P= Lower of the above P= 87,25 psi

14/12/2017 03:53 p.m. BY:Fabio A Hincapie PAGE 1 OF 2


ASME CODE CALCULATIONS SECTION VIII DIVISION 1 2004 EDITION
2006 ADDENDA

TORICONICAL HEAD CALCULATIONS JOB No. 101241

MAWP = P-H MAWP= 87,25 psi

4.0 Small End Calculations

Small End Shell Material SA 105 & SA 36


Allowable Stress at Design Temp. Ss= 16600 psi
Small End Radius R= 2,125 inch
Shell Longitudinal Joint Efficiency E1= 0,55
Cone Longitudinal Joint Efficiency E2= 0,65
Cone Thickness at Small End tc= 0,199 inch
Small end Shell Thickness ts= 0,15 inch
Axial Load in the Small End f2= 500,000 lb/in.

P/SsE1= 0,010
D= 8,717 °

The Small End Junction requires Reinforcement Calculations

k= 1,0000
Qs=P(R+C)/2+f2 Qs= 592,4375 lb/in
Ars=[kQs(R+C)/(SsE1)](1-DELTA/ALFA)tanALFA Ars= 0,072503 Sq.In.
t=P(R+C)/(SsE1-0.6P) t= 0,020366 inch
tr=P(Dm+2C)/[2cosALFA(SE2-0.6P)] tr= 0,042037 inch
Aes=[0.78Sqrt[(R+C)(ts-C)][(ts-t-C)+(tc-tr-C)/CosALFA] Aes= 0,076 inch2
Aes  0.78 ( R  C )  (ts  C )  (ts  t  C )  (tc  tr  C ) / Cos 
M=1/4[3+Sqrt[L/(r+C)]
t=PLM/(2SE-0.2P) t= 0,000 inch
treq=t + C treq= 0,0000 inch

2.3 Head Thickness Calculations

treq=Greater of the above treq= 0,0000 inch


tactual= 0,0000 inch
tnom= 0,0000 inch
rmin=3tnom rmin= 0,0000 inch

3.1 MAWP Hot and Corroded Calculations

P=2SEtcos a/(Di+1.2tcos a) P= 2,64 psi


P=2SEt/(LM+0.2t) P= 1,89 psi
P= Lower of the above P= 0,00 psi
MAWP = P-H MAWP= 0,00 psi
P=2SEtcos a/(Di+1.2tcos a) P= 0,00 psi
P=2SEt/(LM+0.2t) P= 0,00 psi
P= Lower of the above P= 0,00 psi

14/12/2017 03:53 p.m. BY:Fabio A Hincapie PAGE 2 OF 2

You might also like