switch: ?
? -- Present list of available commands
boot -- Load and boot an executable image
cat -- Concatenate (type) file(s)
copy -- Copy a file
delete -- Delete file(s)
dir -- List files in directories
flash_init -- Initialize flash filesystem(s)
format -- Format a filesystem
fsck -- Check filesystem consistency
help -- Present list of available commands
load_helper -- Load and initialize a helper image
memory -- Present memory heap utilization information
mkdir -- Create dir(s)
more -- Concatenate (display) file(s)
rename -- Rename a file
reset -- Reset the system
rmdir -- Delete empty dir(s)
set -- Set or display environment variables
set_bs -- Set attributes on a boot sector filesystem
set_param -- Set system parameters in flash
sleep -- Pause (sleep) for a specified number of seconds
-- MORE --
trap -- Cause a software breakpoint to occur
type -- Concatenate (type) file(s)
unset -- Unset one or more environment variables
version -- Display boot loader version
switch: reset
Are you sure you want to reset the system (y/n)?y
System resetting...
Base ethernet MAC Address: 00:1b:0d:50:96:00
Xmodem file system is available.
The password-recovery mechanism is enabled.
Initializing Flash...
flashfs[0]: 601 files, 19 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32514048
flashfs[0]: Bytes used: 7714304
flashfs[0]: Bytes available: 24799744
flashfs[0]: flashfs fsck took 10 seconds.
...done Initializing Flash.
Boot Sector Filesystem (bs) installed, fsid: 3
done.
Loading "flash:c2960-lanbase-mz.122-25.SEE3/c2960-lanbase-mz.122-
25.SEE3.bin"...@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@
File "flash:c2960-lanbase-mz.122-25.SEE3/c2960-lanbase-mz.122-25.SEE3.bin"
uncompressed and installed, entry point: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C2960 Software (C2960-LANBASE-M), Version 12.2(25)SEE3,
RELEASE SOFTWARE (fc2)
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Thu 22-Feb-07 13:57 by myl
Image text-base: 0x00003000, data-base: 0x00AA3380
Initializing flashfs...
flashfs[1]: 601 files, 19 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 32514048
flashfs[1]: Bytes used: 7714304
flashfs[1]: Bytes available: 24799744
flashfs[1]: flashfs fsck took 1 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
POST: CPU MIC register Tests : Begin
POST: CPU MIC register Tests : End, Status Passed
POST: PortASIC Memory Tests : Begin
POST: PortASIC Memory Tests : End, Status Passed
POST: CPU MIC PortASIC interface Loopback Tests : Begin
POST: CPU MIC PortASIC interface Loopback Tests : End, Status Passed
POST: PortASIC RingLoopback Tests : Begin
POST: PortASIC RingLoopback Tests : End, Status Passed
POST: PortASIC CAM Subsystem Tests : Begin
POST: PortASIC CAM Subsystem Tests : End, Status Passed
POST: PortASIC Port Loopback Tests : Begin
POST: PortASIC Port Loopback Tests : End, Status Passed
Waiting for Port download...Complete
cisco WS-C2960-24TT-L (PowerPC405) processor (revision C0) with 61440K/4088K bytes
of memory.
Processor board ID FOC1122U3C6
Last reset from power-on
1 Virtual Ethernet interface
24 FastEthernet interfaces
2 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.
64K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address : 00:1B:0D:50:96:00
Motherboard assembly number : 73-10390-03
Power supply part number : 341-0097-02
Motherboard serial number : FOC112219DX
Power supply serial number : DCA111780AR
Model revision number : C0
Motherboard revision number : C0
Model number : WS-C2960-24TT-L
System serial number : FOC1122U3C6
Top Assembly Part Number : 800-27221-02
Top Assembly Revision Number : D0
Version ID : V02
CLEI Code Number : COM3L00BRA
Hardware Board Revision Number : 0x01
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 26 WS-C2960-24TT-L 12.2(25)SEE3 C2960-LANBASE-M
Press RETURN to get started!
00:00:39: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to
down
00:00:39: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan
00:00:59: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2960 Software (C2960-LANBASE-M), Version 12.2(25)SEE3,
RELEASE SOFTWARE (fc2)
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Thu 22-Feb-07 13:57 by myl
Would you like to terminate autoinstall? [yes]:
--- System Configuration Dialog ---
Would you like to enter the initial configuration dialog? [yes/no]: ?
% Please answer 'yes' or 'no'.
Would you like to enter the initial configuration dialog? [yes/no]:
% Please answer 'yes' or 'no'.
Would you like to enter the initial configuration dialog? [yes/no]: yes
At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.
Basic management setup configures only enough connectivity
for management of the system, extended setup will ask you
to configure each interface on the system
Would you like to enter basic management setup? [yes/no]: yes
Configuring global parameters:
Enter host name [Switch]: Kelompok5
The enable secret is a password used to protect access to
privileged EXEC and configuration modes. This password, after
entered, becomes encrypted in the configuration.
Enter enable secret: admin
The enable password is used when you do not specify an
enable secret password, with some older software versions, and
some boot images.
Enter enable password: admin
% Please choose a password that is different from the enable secret
Enter enable password: admin
The virtual terminal password is used to protect
access to the router over a network interface.
Enter virtual terminal password: admin
Configure SNMP Network Management? [no]: no
Current interface summary
Interface IP-Address OK? Method Status Protocol
Vlan1 unassigned YES unset up down
FastEthernet0/1 unassigned YES unset down down
FastEthernet0/2 unassigned YES unset down down
FastEthernet0/3 unassigned YES unset down down
FastEthernet0/4 unassigned YES unset down down
FastEthernet0/5 unassigned YES unset down down
FastEthernet0/6 unassigned YES unset down down
FastEthernet0/7 unassigned YES unset down down
FastEthernet0/8 unassigned YES unset down down
FastEthernet0/9 unassigned YES unset down down
FastEthernet0/10 unassigned YES unset down down
FastEthernet0/11 unassigned YES unset down down
FastEthernet0/12 unassigned YES unset down down
FastEthernet0/13 unassigned YES unset down down
FastEthernet0/14 unassigned YES unset down down
FastEthernet0/15 unassigned YES unset down down
FastEthernet0/16 unassigned YES unset down down
FastEthernet0/17 unassigned YES unset down down
FastEthernet0/18 unassigned YES unset down down
FastEthernet0/19 unassigned YES unset down down
FastEthernet0/20 unassigned YES unset down down
FastEthernet0/21 unassigned YES unset down down
FastEthernet0/22 unassigned YES unset down down
FastEthernet0/23 unassigned YES unset down down
FastEthernet0/24 unassigned YES unset down down
GigabitEthernet0/1 unassigned YES unset down down
GigabitEthernet0/2 unassigned YES unset down down
Enter interface name used to connect to the
management network from the above interface summary: FastEthernet0/24
Configuring interface FastEthernet0/24:
Configure IP on this interface? [no]: 192.168.5.5
% Please answer 'yes' or 'no'.
Configure IP on this interface? [no]: yes
IP address for this interface: 192.168.5.5
Subnet mask for this interface [255.255.255.0] : 255.255.255.0
Class C network is 192.168.5.0, 24 subnet bits; mask is /24
Would you like to enable as a cluster command switch? [yes/no]: no
The following configuration command script was created:
hostname Kelompok5
enable secret 5 $1$s9wS$yaw/oC/NMParHB.I.DekR/
enable password admin
line vty 0 15
password admin
no snmp-server
interface Vlan1
shutdown
no ip address
interface FastEthernet0/1
interface FastEthernet0/2
interface FastEthernet0/3
interface FastEthernet0/4
!
interface FastEthernet0/5
interface FastEthernet0/6
interface FastEthernet0/7
interface FastEthernet0/8
interface FastEthernet0/9
interface FastEthernet0/10
interface FastEthernet0/11
interface FastEthernet0/12
interface FastEthernet0/13
interface FastEthernet0/14
interface FastEthernet0/15
interface FastEthernet0/16
interface FastEthernet0/17
!
interface FastEthernet0/18
interface FastEthernet0/19
interface FastEthernet0/20
interface FastEthernet0/21
interface FastEthernet0/22
interface FastEthernet0/23
interface FastEthernet0/24
no shutdown
ip address 192.168.5.5 255.255.255.0
interface GigabitEthernet0/1
interface GigabitEthernet0/2
end
[0] Go to the IOS command prompt without saving this config.
[1] Return back to the setup without saving this config.
[2] Save this configuration to nvram and exit.
Enter your selection [2]: 2
The enable password you have chosen is the same as your enable secret.
This is not recommended. Re-enter the enable password.
ip address 192.168.5.5 255.255.255.0
% Invalid input detected at '^' marker.
Building configuration...
[OK]
Use the enabled mode 'configure' command to modify this configuration.
Kelompok5>
00:04:21: %LINK-5-CHANGED: Interface Vlan1, changed state to administratively down
Kelompok5>enable
Password:
Kelompok5#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Kelompok5(config)#vlan 20
Kelompok5(config-vlan)#name admin
Kelompok5(config-vlan)#int fa0/2
Kelompok5(config-if)#swit
Kelompok5(config-if)#switchport mod
Kelompok5(config-if)#switchport mode ac
Kelompok5(config-if)#switchport mode access
Kelompok5(config-if)#swi
Kelompok5(config-if)#switchport ac
Kelompok5(config-if)#switchport access vl
Kelompok5(config-if)#switchport access vlan 20
Kelompok5(config-if)#int fa0/3
Kelompok5(config-if)#sw
Kelompok5(config-if)#switchport ac
Kelompok5(config-if)#switchport mo
Kelompok5(config-if)#switchport mode ac
Kelompok5(config-if)#switchport mode access
Kelompok5(config-if)#sw
Kelompok5(config-if)#switchport ac
Kelompok5(config-if)#switchport access v
Kelompok5(config-if)#switchport access vlan 20
Kelompok5(config-if)#int fa0/1
Kelompok5(config-if)#sw
Kelompok5(config-if)#switchport ac
Kelompok5(config-if)#switchport access tr
Kelompok5(config-if)#switchport mo
Kelompok5(config-if)#switchport mode tr
Kelompok5(config-if)#switchport mode trunk
Kelompok5(config-if)#int fa0/4
Kelompok5(config-if)#ex
Kelompok5(config)#vlan 10
Kelompok5(config-vlan)#name karyawan
Kelompok5(config-vlan)#int fa0/4
Kelompok5(config-if)#sw
Kelompok5(config-if)#switchport mo
Kelompok5(config-if)#switchport mode ac
Kelompok5(config-if)#switchport mode access
Kelompok5(config-if)#sw
Kelompok5(config-if)#switchport ac
Kelompok5(config-if)#switchport access v
Kelompok5(config-if)#switchport access vlan 10
Kelompok5(config-if)#ex
Kelompok5(config)#ex
% Ambiguous command: "ex"
Kelompok5(config)#do wr
Building configuration...
[OK]
Kelompok5(config)#conf t
% Invalid input detected at '^' marker.
Kelompok5(config)#enable
% Incomplete command.
Kelompok5(config)#?
Configure commands:
aaa Authentication, Authorization and Accounting.
access-list Add an access list entry
alias Create command alias
archive Archive the configuration
arp Set a static ARP entry
banner Define a login banner
boot Boot Commands
buffers Adjust system buffer pool parameters
cdp Global CDP configuration subcommands
class-map Configure QoS Class Map
clock Configure time-of-day clock
cluster Cluster configuration commands
cns CNS agents
control-plane Configure control plane services
default Set a command to its defaults
default-value Default character-bits values
define interface range macro definition
do To run exec commands in config mode
dot1x IEEE 802.1X Global Configuration Commands
downward-compatible-config Generate a configuration compatible with older
software
eap EAP Global Configuration Commands
enable Modify enable password parameters
end Exit from configure mode
errdisable Error disable
exception Exception handling
exit Exit from configure mode
file Adjust file system parameters
help Description of the interactive help system
hostname Set system's network name
interface Select an interface to configure
ip Global IP configuration subcommands
ixi IXI Config command
kron Kron interval Facility
lacp LACP configuration
line Configure a terminal line
link Enable Link State Tracking feature
logging Modify message logging facilities
login Enable secure login checking
mac Global MAC configuration subcommands
mac-address-table Configure the MAC address table
macro Create a command macro
map-class Configure static map class
map-list Configure static map list
memory Configure memory management
mls mls global commands
monitor Monitoring different system events
mvr Enable/Disable MVR on the switch
no Negate a command or set its defaults
ntp Configure NTP
parser Configure parser
platform platform specific config commands
policy-manager Policy Manager configuration commands
policy-map Configure QoS Policy Map
port-channel EtherChannel configuration
priority-list Build a priority list
privilege Command privilege parameters
process Configure process
process-max-time Maximum time for process to run before
voluntarily relinquishing processor
queue-list Build a custom queue list
regexp regexp commands
resource Configure Resource settings
rmon Remote Monitoring
rtr RTR base configuration
scheduler Scheduler parameters
sdm Switch database management
service Modify use of network based services
setup Configure setup options
shutdown Shutdown system elements
snmp Modify non engine SNMP parameters
snmp-server Modify SNMP engine parameters
spanning-tree Spanning Tree Subsystem
stackmaker Specify stack name and add its member
standby Global HSRP configuration commands
system Set the system configuration
table-map Configure Table Map
tacacs-server Modify TACACS query parameters
template Select a template to configure
tftp-server Provide TFTP service for netload requests
time-range Define time range entries
udld Configure global UDLD setting
username Establish User Name Authentication
vlan Vlan commands
vmps VMPS settings
vtp Configure global VTP state
Kelompok5(config)#inte
Kelompok5(config)#interface vlan 10
Kelompok5(config-if)#
00:16:33: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan10, changed state to
down
Kelompok5(config-if)#ip ad
Kelompok5(config-if)#ip address 10.10.10.254 255.255.255.0
Kelompok5(config-if)#ex
Kelompok5(config)#inte
Kelompok5(config)#interface vl
Kelompok5(config)#interface vlan 20
Kelompok5(config-if)#ip ad
Kelompok5(config-if)#ip address
00:17:10: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan20, changed state to
down
% Incomplete command.
Kelompok5(config-if)#int
Kelompok5(config-if)#int
Kelompok5(config-if)#ip ad
Kelompok5(config-if)#ip address 20.20.20.254 255.255.255.0
Kelompok5(config-if)#ex
Kelompok5(config)#sh vlan
% Invalid input detected at '^' marker.
Kelompok5(config)#ex
% Ambiguous command: "ex"
Kelompok5(config)#sh vlan
% Invalid input detected at '^' marker.
Kelompok5(config)#ex
% Ambiguous command: "ex"
Kelompok5(config)#exit
Kelompok5#
00:18:01: %SYS-5-CONFIG_I: Configured from console by consolesh
% Type "show ?" for a list of subcommands
Kelompok5#sh vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/1, Fa0/5, Fa0/6, Fa0/7
Fa0/8, Fa0/9, Fa0/10, Fa0/11
Fa0/12, Fa0/13, Fa0/14, Fa0/15
Fa0/16, Fa0/17, Fa0/18, Fa0/19
Fa0/20, Fa0/21, Fa0/22, Fa0/23
Fa0/24, Gi0/1, Gi0/2
10 karyawan active Fa0/4
20 admin active Fa0/2, Fa0/3
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-default act/unsup
1005 trnet-default act/unsup
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
10 enet 100010 1500 - - - - - 0 0
20 enet 100020 1500 - - - - - 0 0
1002 fddi 101002 1500 - - - - - 0 0
1003 tr 101003 1500 - - - - - 0 0
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1004 fdnet 101004 1500 - - - ieee - 0 0
1005 trnet 101005 1500 - - - ibm - 0 0
Remote SPAN VLANs
------------------------------------------------------------------------------
Primary Secondary Type Ports
------- --------- ----------------- ------------------------------------------
Kelompok5#do wr
Kelompok5#do write
% Invalid input detected at '^' marker.
Kelompok5#enable
Kelompok5#enable
Kelompok5#
00:19:50: %LINK-3-UPDOWN: Interface FastEthernet0/2, changed state to up
00:19:51: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2,
changed state to up
Kelompok5#do write
% Invalid input detected at '^' marker.
Kelompok5#enable
Kelompok5#exit
Kelompok5 con0 is now available
Press RETURN to get started.
Kelompok5>do write
% Invalid input detected at '^' marker.
Kelompok5>enable
Password:
00:20:19: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan20, changed state to
up
Kelompok5#do write
% Invalid input detected at '^' marker.
Kelompok5#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Kelompok5(config)#do write
Building configuration...
[OK]
Kelompok5(config)#
00:22:54: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to up
00:22:55: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3,
changed state to up
00:23:00: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3,
changed state to down
00:23:01: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to down
Kelompok5(config)#
00:23:16: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to up
00:23:17: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3,
changed state to up
Kelompok5(config)#ping 20.20.20.2
% Invalid input detected at '^' marker.
Kelompok5(config)#exit
Kelompok5#ping
00:24:24: %SYS-5-CONFIG_I: Configured from console by console
Protocol [ip]:
Kelompok5#ping 20.20.20.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 20.20.20.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/202/1007 ms
Kelompok5#
00:26:06: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2,
changed state to down
00:26:07: %LINK-3-UPDOWN: Interface FastEthernet0/2, changed state to down
00:26:09: %LINK-3-UPDOWN: Interface FastEthernet0/2, changed state to up
00:26:10: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2,
changed state to up
00:26:11: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2,
changed state to down
00:26:12: %LINK-3-UPDOWN: Interface FastEthernet0/2, changed state to down
