HIT photovoltaic module HIP-205NKHB5

HIP-200NKHB5

The SANYO HIT ( Heterojunction with Intrinsic Thin layer ) solar cell is made of a thin mono
crystalline silicon wafer surrounded by ultra-thin amorphous silicon layers. This product provides
the industry's leading performance and value using state-of-the-art manufacturing techniques.

Benefit in Terms of Performance

The HIT cell and module have very high
conversion efficiency in mass production.
Model Cell Efficiency Module Efficiency

HIP-205NKHB5 18.4% 16.0%

HIP-200NKHB5 18.0% 15.6%

High performance at high temperatures

Even at high temperatures, the HIT solar cell can
maintain higher efficiency than a conventional
crystalline silicon solar cell.

[Changes in generated power daytime]

Module temp.75℃
normalized output power

0.8 approx.
10%up HIT

0.5 c-Si

Kobe (Japan), 24. July 2007,

faced to south, tilt angle 30°

5 7 9 11 13 15 17 19
time

Environmentally-Friendly Solar Cell

More Clean Energy
HIT Solar Cell Structure HIT can generate more clean Energy than other
conventional crystalline solar cells.
Ultra-thin amorphous silicon layer

Front-side Thin mono Special Features

electrode
crystalline
n silicon wafer SANYO HIT solar modules are 100% emission
Rear-side
electrode free, have no moving parts and produce no
Ultra-thin amorphous silicon layer noise.The dimensions of the HIT modules
allow space-saving installation and
Development of HIT solar cell was supported in part
by the New Energy and Industrial Technology
achievement of maximum output power
Development Organization (NEDO). possible on given roof area.

Photovoltaic Module
NKH205/200
 Electrical and Mechanical Characteristics
HIP-205NKHB5,HIP-200NKHB5
Reference data for model HIP-205NKHB5
Models HIP-xxxNKHB5
Dependence on irradiance o
Electrical data 205 200 6.00
Cell temperature: 25 C
1000W/m2
Maximum power (Pmax) [W] 205 200
Max. power voltage (Vmp) [V] 5.00
40.7 40.0
800W/m2
Max. power current (Imp) [A] 5.05 5.00
4.00

Current[A]
Open circuit voltage (Voc) [V] 50.3 49.6 600W/m2
Short circuit current (Isc) [A] 5.54 5.50 3.00

Warranted minimum power (Pmin) [W] 194.75 190.0 400W/m2

2.00
Maximum over current rating [A] 15
200W/m2
Output power tolerance [%] +10/-5 1.00

Maximum system voltage [V] 600

0.00
Temperature coefficient of Pmax [%/°C] -0.30 -0.33
0 10 20 30
Voltage[V]
40 50 60

Voc [V/°C] -0.126 -0.125

lsc [mA/°C] 1.66 1.65
Dependence on temperature
Note 1: Standard Test Conditions: Air mass 1.5, Irradiance = 1000W/m2,
AM-1.5, 1000W/m2
Cell temperature = 25°C 6.00
Note 2: The values in the above table are nominal
75℃
5.00

50℃
4.00
Dimensions and weight 25℃
unit: mm
Current[A]

812 35 3.00 0℃
B

JUNCTION 2.00
B

BOX
(1020)

LABEL 1.00

negative(−) (＋)positive
0.00
0 10 20 30 40 50 60
ＣＯＮＮＥＣＴＯＲ
Voltage[V]

Certificates
1580

Please consult your local dealer for more information.

A A

Front side Backside

Weight: 15kg
35

35
(7)

(12) (7) 12

Section A-A Section B-B

Warranty Certificate Number: PV05-53203-1012

Power output: 20 years (80% of minimum output power)
An above number is a certification number by JET.
Product workmanship: 2 years
JET: Japan Electrical Safety & Environment Technology Laboratories
(Based on contract terms)

CAUTION! Please read the operating instructions carefully before using the products.
Due to our policy of continual improvement the products covered by this brochure may be changed without notice.

[ASIA & Oceania]

 
International Sales & Marketing H.Q.
Tel.81-6-6994-7359 Fax.81-6-6994-7083

Solar Division

http://www.sanyo.com/solar
12/08

email: [email protected]