ON-SITE GUIDE BS 7671 : 2001 (2004) Wiring Regulations 16th Edition Including Amendments No 1 : 2002 and No 2 : 2004 oe a a —_ an '? = O PriPublished by: The IEE, LONDON, UK ©2004 The Institution of Electrical Engineers Printed February 1992 Reprinted May 1993, with amendments Reprinted July 1993, with amendment (Appendix 9) Reprinted February 1994, with amendments Revised February 1995 to incorporate Amendment No 1 to BS 7671 Revised June 1996, new cover only Revised June 1998 to incorporate Amendment No 2 to BS 7671 Revised Feb 2002 to incorporate BS 7671 : 2001, inc Amd No 1: 2002 Reprinted July 2003, new cover only Revised April 2004 to incorporate BS 7671 : 2001, inc Amd No 2: 2004 This publication is copyright under the Berne Convention 2003 and the Universal Copyright Convention. All rights reserved. Apart from any fair dealing for the purposes of research or private study, or criticism or review, as permitted under the Copyright, Designs and Patents Act, 1988, this publication may be reproduced, stored or transmitted, in any form or by any means, only with the prior permission in writing of the publishers, or in the case of reprographic reproduction in accordance with the terms of licences issued by the Copyright Licensing Agency. Inquiries concerning reproduction outside those terms should be sent to the publishers at the undermentioned address: The IEE, Michael Faraday House, Six Hills Way, STEVENAGE, SG1 2AY, United Kingdom Copies may be obtained from The IEE: The IEE P.O. Box 96 Stevenage SG1 2SD, UK Tel: +44 (0)1438 767 328 Email: [email protected] http:/www.iee.org/Publish/Books/WireAssod’ While the publisher and contributors believe that the information and guidance given in this work is correct, all parties must rely upon their own skill and judgement when making use of it. Neither the publisher nor any contributor assume any liability to anyone for any loss or damage caused by any error or omission in the work, whether such error or omission is the result of negligence or any other cause. Where reference is made to | lation it is not to be considered as legal advice. Any and all such liability is disclaimed. ISBN 0 86341 3749 2PREFACE FOREWORD SECTION 1. 11 1.2 SECTION 2. 2.1 2.2 SECTION 3. SECTION 4. 41 4.2 43 44 45 4.6 47 48 49 CONTENTS INTRODUCTION Scope Basic Information Required THE SERVICE POSITION General Layout of Equipment Function of Components: PROTECTION Types of Protective Device(s) Overload Protection Fault Current Protection Protection Against Electric Shock Disconnection Times Residual Current Devices (RCD) BONDING AND EARTHING Main Equipotential Bonding of Metal Services (Figs 4a, 4b, 4c) Main Earthing and Main Equipotential Bonding Conductor Cross-sectional Areas Main Equipotential Bonding - Plastic Services Earthing Supplementary Equipotential Bonding in Locations of Increased Shock Risk - Metal Pipework Supplementary Bonding in other Locations - Metal Pipework Supplementary Bonding of Plastic Pipe Installations Earth Electrode (Fig 4c) Types of Earth Electrode 4.10 Typical Earthing Arrangements 24 24 25 2 2 26 26 32 32 33SECTION 5. SECTION 6. 6.1 SECTION 7. 71 72 73 74 SECTION 8. 8.1 8.2 8.3 84 ‘SECTION 9. 9.1 9.2 9.3 SECTION 10. GUIDANCE NOTES ON INITIAL TESTING OF ISOLATION AND SWITCHING Isolation Functional Switching Switching Off for Mechanical Maintenance Emergency Switching LABELLING Labels to be Provided FINAL CIRCUITS Final Circuits Using the Tabulated Final Circuits Installation Considerations Smoke Alarms and Emergency Lighting SPECIAL LOCATIONS GIVING RISE TO INCREASED RISK OF ELECTRIC SHOCK Locations Containing a Bath or Shower Shower Cubicles in a Room used for Other Purposes Temporary and Garden Buildings, Domestic Garages, Buildings of Lightweight Construction etc Earthing requirements of Equipment having High Protective Conductor Current INSPECTION AND TESTING inspection and Testing Inspection Testing INSTALLATIONS 10.1 Safety and equipment 10.2 Sequence of Tests 10.3 Test Procedures 60 60 62 62 65 66 67SECTION 11. OPERATION OF RESIDUAL CURRENT OPERATED DEVICES(RCDs) AND RESIDUAL CURRENT BREAKERS WITH OVERCURRENT PROTECTION (RCBOs) 11.1 General Test Procedure 11,2 General purpose RCDs to BS 4293 11.3 General purpose RCCBs to BS EN 61008 or RCBOs to BS EN 61009 11.4 RCD protected socket-outlets to BS 7288 11.5 Additional Requirement for Supplementary Protection 11.6 Integral Test Device 81 81 81 81 81 82 82APPENDICES Maximum demand and diversity 2. Maximum permissible measured earth fault loop impedance 3 Notes on the selection of types of cable and flexible cord for particular uses and external influences 4 Notes on methods of support for cables, conductors and wiring systems 5 Cable capacities of conduit and trunking 6 Current-carrying capacities and voltage drop for copper conductors 7 Certification and reporting 8 Standard circuit arrangement for household and similar installations 9 Resistance of copper and aluminium conductors 10 Protective conductor sizing 11 Identification of conductors INDEXES (i) The installation (ii) Bonding and earthing (iii) Special locations and RCDs (iv) w) Inspection and testing Alphabetical Page 88 94 100 109 115 127 150 157 161 164 170 173 174 176 178Co-operating Organisations The IEE acknowledges the contribution made by the following organisations in the preparation of this guide. Association of Manufacturers of Domestic Electrical Appliances § A MacConnacher BSc CEng MIEE BEAMA Installation Ltd Eur Ing M H Mullins BA CEng FIEE FIIE British Cables Association CK Reed | Eng MIIE British Electrotechnical & Allied Manufacturers Association Ltd R F B Lewington MIEE British Electrotechnical Approvals Board P D Stokes MA CEng MRAeS. British Standards Institution MR Danvers City & Guilds of London Institute HR Lovegrove IEng FIIE Electrical Contractors’ Association D Locke IEng MIIE ACIBSE Electrical Contractors’ Association of Scotland t/a SELECT D Millar IEng MIIE MILE Electricity Association Limited DJ Start BSc CEng MIEE ERA Technology Ltd M W Coates BEng Federation of the Electronics Industry F W Pearson CEng MIIE The GAMBICA Association Ltd K A Morriss BSc CEng MIEE Health & Safety Executive Eur Ing J A McLean BSc CEng FIEE FIOSH Institution of Incorporated Engineers P Tootill IEng MIIE Lighting Association K R Kearney IEng MIIE National Inspection Council for Electrical Installation Contracting Safety Assessment Federation Limited J Gorman BSc (Hons) CEng MIEE Society of Electrical and Mechanical Engineers serving Local Government CJ Tanswell CEng MIEE MCIBSE Editor PR L Cook CEng FIEE MCIBSEPREFACE The On-Site Guide is one of a number of publications prepared by the IEE to simplify some aspects of BS 7671 : 2001 (2004) Requirements for Electrical Installations (IEE Wiring Regulations Sixteenth Edition). BS 7671 is a joint publication of the British Standards Institution and the Institution of Electrical Engineers. The scope generally follows that of BS 7671. It includes material not included in BS 7671, provides background to the intentions of BS 7671, and gives other sources of information. However, this guide does not ensure compliance with BS 7671. It is a simple guide to the requirements of BS 7671, and electricians should always consult BS 7671 to satisfy themselves of compliance. It is expected that persons carrying out work in accordance with this guide will be competent to do so. Electrical installations in the United Kingdom which comply with the IEE Wiring Regulations, BS 7671, should also comply with the Statutory Regulations such as the Electricity at Work Regulations 110-01-01 1989. It cannot be guaranteed that BS 7671 complies with all relevant Regulations and it is stressed that it is essential to establish what statutory and other Regulations apply and to _ install accordingly. For example, an installation in Licensed Premises may App 2(vi) have requirements different from or additional to BS 7671 and these will take precedence over BS 7671.FOREWORD This Guide is concerned with limited application of BS 7671 in accordance with para 1.1 Scope. Part 1 BS 7671 and the On-Site Guide are not design guides. It is essential to prepare a schedule of the work to be done prior to commencement or alteration of an electrical installation and to provide all necessary information and operational manuals of any equipment supplied to the user on completion. Any specification should set out the detailed design and provide sufficient information to enable competent persons to carry out the installation and to commission it. The specification must include a description of how the system is to operate and all of the design and operational parameters. The specification must provide for all the commissioning procedures that will be required and for the production of any operational manual. It must be noted that it is a matter of contract as to which person or organisation is responsible for the production of the parts of the design, specification and any operational manual. The persons or organisations who may be concerned in the preparation of the specification include: The Designer(s) The Installer(s) The Electricity Distributor The Installation Owner and/or User The Architect The Fire Prevention Officer The Planning Supervisor All Regulatory Authorities Any Licensing Authority The Health and Safety ExecutiveIn producing the specification advice should be sought from the installation owner and/or user as to the intended use. Often, such as in a speculative building, the detailed intended use is unknown. In those circumstances the specification and/or the operational manual must set out the basis of use for which the installation is suitable. Precise details of each item of equipment should be obtained from the manufacturer and/or supplier and compliance with appropriate standards confirmed. The operational manual must include a description of how the system as installed is to operate and all commissioning records. The manual should also include manufacturers’ technical data for all items of switchgear, luminaires, accessories, etc and any special instructions that may be needed. The Health and Safety at Work etc Act 1974 Section 6 and the Construction (Design and Management) Regulations 1994 are concerned with the provision of information. Guidance on the preparation of technical manuals is given in BS 4884 (Specification for technical manuals) and BS 4949 (Recommendations for the presentation of technical information about products and services in the construction industry). The size and complexity of the installation will dictate the nature and extent of the manual. 10SECTION 1. 11 ON-SITE GUIDE INTRODUCTION Scope This Guide is for electricians (skilled persons). It covers the following installations: (a) (b) domestic installations generally, including off-peak supplies, and supplies to associated garages, out-buildings and the like industrial and commercial single- and three-phase installations where the distribution board(s) or consumer unit is located at or near the distributor's cut-out. Note: Special Installations or Locations (Part 6 of BS 7671) are generally Part 6 excluded from this Guide. Advice is given on installations in locations containing a bath or shower (8.1), temporary and garden buildings etc (8.3) and personal computer circuits in office locations (8.4). This Guide is restricted to installations : 313-01-01 @ (i) (iii) tiv) at a supply frequency of 50 Hertz at a nominal single-phase voltage of 230 V a.c. single-phase and 230/400 V a.c. three-phase fed through a distributor's cut-out having a fuse or fuses to BS 1361 Type !! or through fuses to BS 88-2 or BS 88-6 with a maximum value of the earth fault loop impedance outside the consumer's installation as follows: Earth return via sheath (TN-S system): 0.8 ohm Earth return via combined neutral and earth conductor (TN-C-S system): 0.35 ohm TT systems: 21 ohms excluding consumer's earth electrode 11 Sect12 Sec1 This Guide contains information which may be required in general installation work, e.g. conduit and trunking capacities, bending radii of cables. This Guide introduces the use of conventional circuits, which are discussed in Section 7. Because of simplification this Guide may not give the most economical result. This Guide is not a replacement for BS 7671, which should always be consulted. Defined terms according to Part 2 of BS 7671 are used in this Guide. In conformance with the definitions of BS 7671, throughout this Guide the term ‘live part’ is used to refer to a conductor or conductive part intended to be energised in normal use, including a neutral conductor. For convenience in use, and in accordance with current UK manufacturing practice, the Part 2 terminals of electrical equipment shown in Figs 10.1 to 10.5 figs 3to7 have been identified by the letters L, N and E. Further information is available in the series of Guidance Notes published by the Institution. For new domestic installations and major refurbishments account should be taken of the recomrnendations in Approved Document B, issued as guidance on the Building Regulations 1991. Part B1, Section 1 advises that, if dwellings are not protected by an automatic fire detection and alarm system to Part 6 of BS 5839, a suitable number of mains operated self-contained smoke alarms to BS 5446 be installed. In Scotland the Building Standards (Scotland) Regulations 1990 apply and installations must comply with The Scottish Office Technical Standards .1.2 Basic Information Required Part 3 Before starting work on an installation that requires a new supply, the electrician should obtain the following information from the distributor: w (i) (iii) (iv) (v) (vi) (vii) the number of phases to be provided 312-02-01 the distributor's requirement for cross-sectional area 313.01-014i) and length of meter tails the maximum prospective fault current (pfc) at the 313.01-01(i) supply terminals the maximum earth loop impedance (Ze) of the earth —_313.01-01() fault path outside the consumer's installation the type and rating of the distributor's fusible cut-out — 313.01-01(v) or protective device the distributor's requirement regarding the size of main 547-0201 equipotential bonding the earthing arrangement and type of system 312-03-01 (viii) the arrangements for the incoming cable and metering. 31301010) For existing installations, electricians should satisfy themselves as to the suitability of the supply including the earthing arrangement. 13 Sec1SECTION 2. THE SERVICE POSITION 2.1 General Layout of Equipment The general layout of the equipment at the service position is shown in Figs 2a and 2b. 2.2 Function of Components: (i) Distributor’s Cut-out This will be sealed to prevent the fuse being withdrawn 31301-01() by unauthorised persons. When the meter tails and consumer unit are installed in accordance with the requirements of the distributor the cut-out may be assumed to provide fault current protection up to the consumer's main switch. (ii) Supplier's Meter This will be sealed by the supplier to prevent interference by unauthorised persons. (iii) Meter Tails These are part of the consumer's installation. They 4730204) should be insulated and sheathed or insulated and 521-0703 enclosed in conduit or trunking. Polarity should be indicated by the colour of the 514-06 insulation and the minimum cable size should be 25 mmé. The distributor may specify the maximum length and the minimum cross-sectional area (see 1.2(ii)). Where the meter tails are protected against fault current 473-0204) by the distributor's cut-out the method of installation, maximum length and minimum cross-sectional area must comply with the requirements of the distributor. 14 Sec2Fig 2a: Layout when the supplier does not provide a main switch Note: Earthing arrangements have been omitted for clarity. Tails between the meter and the consumer's installation are provided by the consumer meter ~~ supplier's terminals consumer's meter tails istributor’s cut-out Fig 2b: Layout when the supplier does provide a main switch Note: Earthing arrangements have been omitted for clarity. Tails between any main switch provided by the supplier and the consumer's installation are provided by the consumer consumer's tails Pe supplier’s main switch terminals 15 Sec216 Sec2 (iv) Ww) Supplier’s Switch Some suppliers may provide and install a suitable switch between the meter and the consumer unit. This permits 476-01-01 the supply to the installation to be interrupted without withdrawing the distributor's fuse in the cut-out. Consumer's Controlgear A consumer unit is for use on single-phase installations. part 2 It contains a double-pole main switch and fuses or circuit-breakers (cbs) and perhaps residual current devices (RCDs) or residual current breakers with integral overcurrent protection (RCBOs) for the protection of each final circuit. Alternatively, a separate main switch and distribution board may be provided.SECTION 3. PROTECTION 3.1 Types of Protective Device(s) The consumer unit (or distribution board) contains devices for ch 43 the protection of the final circuits against: (i) overload 433 (ii) short-circuit 434 (iii) earth fault. 434 Functions (i) and (ii) are carried out usually by one device, a fuse or circuit-breaker, Function (iii) may be carried out by the fuse or circuit-breaker 413-02-04 provided for functions (i) and (ii), or by an RCD. An RCBO being a combined circuit-breaker and RCD will carry out functions (i), (ii) and (iii). 3.2 Overload Protection Overload protection is given by the following devices: Fuses to BS 88-2.1 or BS 88-6; BS 1361 and BS 3036; App3 miniature circuit-breakers to BS 3871-1 Types 1, 2 and 3; circuit-breakers to BS EN 60898 types B, C and D; and residual current circuit-breakers with integral overcurrent protection (RCBOs) to BS EN 61009-1. 3.3 Fault Current Protection When a consumer unit to BS EN 60439-3 or BS 5486 : Part 13, 473-02-04 or a fuseboard having fuselinks to BS 88-2.1 or BS 88-6 or BS 1361 is used, then fault current protection will be given by the overload protective device. For other protective devices the breaking capacity must be adequate for the prospective fault current at that point. 3.4 Protection Against Electric Shock (i) Direct Contact 412 Electrical insulation and enclosures and barriers give 412-01-01 protection against direct contact. Non-sheathed insulated conductors must be protected by conduit or 521-07-03 17 Sec318 Sec3 (i) (ii) trunking or be within a suitable enclosure. A 30 mA RCD may be provided to give supplementary protection 412.06 against direct contact, but must not be relied upon for primary protection. Indirect Contact a3 Protection against indirect contact is given by limiting to safe values the magnitude and duration of voltages that may appear under earth fault conditions between simultaneously accessible exposed-conductive-parts of equipment, and between them and _ extraneous- conductive-parts or earth. This may be effected by the: (a) co-ordination of protective devices and circuit 4113-02-04 impedances, or (b) use of RCDs to limit the disconnection time, or 413-02-07 (©) __ use of Class Il equipment or equivalent insulation. 413-03 SELV and PELV SELV 411-02 Separated extra-low voltage (SELV) systems (a) are supplied from isolated safety sources such as 411-02-02 a safety isolating transformer to BS 3535 (b) have no live part connected to earth or the 411-02-05 protective conductor of another system (are enclosed in an insulating sheath additional to 411-02-06 their basic insulation (d) have no exposed-conductive-parts connected to 411-02-07 earth, to exposed-conductive-parts or protective conductors of other systems or to extraneous- conductive-parts. PELV A71-14-01 Protective extra-low (PELV) systems must meet all the 471-14-02 requirements for SELV, except that the circuits are not electrically separated from earth.For SELV and PELV systems protection against direct 411-02-09 contact need not be provided if voltages do not exceed 471-14-02 the following: Location SELV Dry areas 25 V a.c. or 60 Vd.c. 25 Vac. or 60V dc. 411-02-09 Bathrooms, swimming _| Protection required at__| Protection required at | 601-03-02 pools, saunas all voltages all voltages 6602-03-01 6603-03-01 Other areas 12V ac. or 30Vd.c. 6Va.c.or 15Vd.c. 471-01-01 471-14-02 3.5 Disconnection Times 3.5.1 Conventional Circuits For the conventional circuits given in Section 7, the correct disconnection time in seconds (0.4 s or 5s) is obtained by using the protective devices and related maximum circuit lengths in Table 7.1. 3.5.2 Special Circuits A disconnection time of not more than 0.4 s is required for final circuits supplying: (i) portable equipment intended to be moved by hand 413-02-09 while in use (ii) hand-held metal-cased equipment requiring an earth, —413-02-09 and supplied directly or through a socket-outlet (iii) fixed equipment outside the equipotential zone with —_471-08-03 accessible exposed-conductive-parts 3.6 Residual Current Devices (RCD) Note: Residual current device (RCD) is a device type that includes residual current circuit-breakers (RCCBs) and residual current circuit-breakers with integral overcurrent protection (RCBOs). 3.6.1 Protection by an RCD There are a number of instances where an installation is required to incorporate one or more RCDs (RCCB or RCBO). These instances include: 19 Sec320 Sec3 (i) where the earth fault loop impedance is too high to provide the required disconnection time e.g. where the distributor does not provide an earth - TT systems (ii) onsocket-outlet circuits in TT systems (iii) on all socket-outlets that may reasonably be expected to supply portable equipment used outdoors (iv) circuits supplying portable equipment for use outdoors by means of a flexible cable. (v) on socket-outlets in a room, other than a bathroom or shower room, containing a shower cubical. 3.6.2 Applications of RCDs Installations are required to be divided into circuits to avoid danger and minimise inconvenience in the event of a fault and to take account of hazards that might arise from the failure of a single circuit, e.g. a lighting circuit. 30 mA RCDs installed to provide protection to socket-outlets likely to feed portable equipment outdoors should protect only those sockets, see Fig 3b. Where an RCD is fitted only because the earth loop impedance is too high for shock protection to be provided by an overcurrent device, for example in a TT system, the rated residual operating current should not be less than 100 mA. If two RCDs are installed they should preferably control separate circuits, see Fig 3a(i), or a time delay 100 mA or greater RCD (S type) should be installed, see Fig 3a(ii). The use of RCBOs, see Fig 3a(iii), will minimise inconvenience in the event of a fault. The enclosures of RCDs or consumer units incorporating RCDs in TT installations should be of an all-insulated or Class I! construction. Otherwise, additional precautions recommended by the manufacturer need to be taken to prevent faults to earth on the supply side of the RCD. 413-02-19 471-08-06 471-16-01 471-16-02 6601-08-02 314-01-01 314-01-02Fig 3a: Installing RCDs in a TT installation i} consumer unit with separate isolator ii) consumer unit using time delayed RCD as main switch Rote 1 circuits to lights, cooker, water heater, smoke alarms (labelled) as the main switch for the installation consumer unit with insulated enclosure or additional protection to meter and isolator tails consumer unit with insulated enclosure or additional protection to meter tails note 1 2 circuits to portable equipment outdoors and socket-outlets that may reasonably supply portable equipment outdoors (ground floor socket-outlets) 3 time delay (S-type) double-pole RCD to BS EN 61008. This RCD must be clearly identified 21 Sec3Fig 3a cont'd: Installing RCDs in a TT installation 22 Sec3 HD consumer unit with RCBOs consumer unit with insulated enclosure or additional protection to meter tails lan 2 100 mA, note 4 Circuits to lights, cooker, water heating, smoke alarms 5 Circuits to portable equipment outdoors and socket-outlets that may reasonably supply equipment outdoors, and certain equipment in bathrooms - see Table 8.1 3.6.3 Applications of residual current circuit-breakers with overload current protection (RCBOs) In TN systems it is preferable for reliable operation for indirect 413-02-04 shock protection to be provided by overcurrent devices, including RCBOs operating as overcurrent devices; that is, with loop impedances complying with Table 2D of Appendix 2. RCBOs are then providing indirect shock protection as overcurrent devices and supplementary protection against direct contact as 471-16 residual current circuit-breakers (RCCBs). When the designer intends that indirect shock protection is to 413-02-16 be provided by a residual current circuit-breaker (RCCB) or the residual current element of an RCBO, loop impedances are as for an RCD, that is appropriate to the rated residual operating current (Zs < 50 V/ lan), and not more than 200 ohms.Fig 3b: Installing RCDs in a TN-S or TN-C-S installation note 1 The 30 mA RCD and associated cbs may be replaced by residual current breakers with ‘overcurrent protection (RCBOs) on the main switch busbar rail 2 Circuits to lights, cooker, water heating, smoke alarms 3 Circuits to portable equipment outdoors and socket-outlets that may reasonably supply equipment outdoors 23 Sec3SECTION 4. BONDING AND EARTHING 4.1 Main Equipotential Bonding of Metal Services (Figs 4a, 4b, 4c) Main equipotential bonding conductors are required to 413-02-02 connect the following metallic parts to the main earthing terminal, where they are extraneous-conductive-parts: i) metal water service pipes (ii) _ metal gas installation pipes (iii) other metal service pipes (including oil and gas supply pipes) and ducting (iv) metal central heating and air conditioning systems (v) exposed metallic structural parts of the building (vi) lightning protection systems. 4.2 Main Earthing and Main Equipotential Bonding Conductor Cross-Sectional Areas The minimum cross-sectional area (csa) of the main equipotential 547-02-01 bonding conductor is half that of the main earthing conductor. For 100 A TN installations, the main earthing conductor csa needs to be 16 mm2 and that of the main bonding conductors 10 mm2 where the size of the supply Table 54H neutral conductor is not more than 35 mm2. However, local public electricity distribution network conditions may require larger conductors. For other conditions see Table 10A of Appendix 10. For TT installations see Fig 4c. Note that: (i) only copper conductors should be used; copper covered 542-03-03 aluminium conductors or aluminium conductors or structural steel can only be used if special precautions outside the scope of this Guide are taken (ii) bonding connections to incoming metal services should 547-02-02 be as near as possible to the point of entry of the services to the premises, but on the consumer's side of any insulating section (iii) the connection to the gas, water, oil, etc service should 47-02-02 be within 600 mm of the service meter, or at the point of entry to the building if the service meter is external,and must be on the consumer's side before any branch pipework and after any insulating section in the service. The connection must be made to hard pipe, not to soft or flexible meter connections {iv) the connection must be made using clamps (to BS 951) 542-03-03 which will not be subject to corrosion at the point of contact () if incoming gas and water services are of plastic, main bonding connections are to be made to metal installation pipes only. 4.3 Main Equipotential Bonding - Plastic Services There is no requirement to main bond an incoming service where both the incoming service pipe and the pipework within the installation are both of plastic. Where there is a plastic incoming service and a metal installation within the premises, main bonding must be carried out, the bonding being applied on the customer's side of any meter, main stop cock or insulating insert. 44 — Earthing Every exposed-conductive-part (a conductive part of equipment 413-02-06 which can be touched and which is not a live part but which 413-02-18 may become live under earth fault conditions) shall be connected by a protective conductor to the main earthing terminal. 4.5 Supplementary Equipotential Bonding in Locations of Increased Shock Risk - Metal Pipework Supplementary equipotential bonding is required only in locations of increased shock risk such as some of those in Part 6 of BS 7671 (471-08-01). In domestic premises, the locations 471-08-01 identified as having increased shock risks are rooms containing a bath or shower (bathrooms) and around swimming pools. In a bathroom or shower room, local supplementary equipotential 601-04-01 bonding is required to be provided connecting together the terminal of protective conductors of each circuit supplying Class | and Class II equipment in zones 1, 2 or 3, and extraneous- conductive-parts in these zones including the following: (i) metal pipes supplying services and metallic waste pipes (e.g. water, gas) 25 Seca26 Seca (ii) metal central heating pipes and air conditioning systems (iii) accessible metal structural parts of the building (metal door architraves, metal handrails, window frames and similar parts are not considered to be extraneous- conductive-parts unless they are connected to metallic structural parts of the building) (iv) metal baths and metal shower basins. Circuit protective conductors may be used as supplementary bonding conductors. The supplementary equipotential bonding may be provided in close proximity to the location. See Section 8.1 for locations containing a bath or shower, A typical installation is shown in Figure 4d. 601-04-01 4.6 Supplementary Bonding in other Locations - Metal 471-08-01 Pipework There is no specific requirement in BS 7671 to supplementary bond the following kitchen pipes, sinks or draining boards metal furniture in kitchens metal pipes and wash hand basins in domestic locations other than bathrooms. Note: Metal waste pipes in contact with earth should be main bonded back to the main earthing terminal. 4.7 Supplementary Bonding of Plastic Pipe Installations Supplementary bonding is not required to metal parts supplied by plastic pipes, such as metal hot and cold water taps supplied from plastic pipes. A metal bath not connected to extraneous-conductive-parts (such as structural steelwork) with plastic hot and cold water pipes and plastic waste pipes does not require supplementary bonding. Supplementary bonding in a bathroom or shower room will still be required between the protective conductors of circuits supplying Class 1 and Class II equipment in the zones e.g. heaters, showers and accessible luminaires, see Figure 4e.Fig 4a: Typical earthing arrangements and protective conductor csa - TN-S meter LABE| yes Lz meter tails 25 mm2 consumer unit or distribution board 2 16 mm earthing bar LABEL | gb 10 mm? [apet]| | 40 mm2 intake 7 ope [rape] int LABEI main earthing metal metal terminal water gas 16 mm2 pipe Pipe main earthing main equipotential conductor bonding conductors supply earth TN-S: Earthed to armour or metallic sheath Note: i) Main equipotential bonding conductors may be separate (as shown) or looped with unbroken conductors. ji) [LABEL J - Safety Electrical Connection - Do Not Remove. LABEL other extraneous- conductive- partsy22s 8z Fig 4b: Typical earthing arrangements and protective conductor csa - TN-C-S meter meter tails 25 mm? 16 mm? consumer unit or distribution board ; (TaBeL] earthing bar intake LABEL | LABEL 9 000 7 10mm? f LABEL | i 16mm — tomm T | other T na main equipotential ee earthing bonding conductors best aboard supply earth terminal : Parts pme metal metal connection water gas pipe pipe iii) LABEL }- Safety Electrical Connection - Do Not Remove. i) Main equipotential bonding conductors may be separate (as shown) or looped with unbroken conductors. ii) Local electricity distribution network conditions may require larger conductors.Fig 4c: Typical earthing arrangements and protective conductor csa - TT meter meter tails 25 mm? RCDs consumer unit or distribution board earthing bar main earthing 6 mm2 conductor 6mm2 [ABEL] BEL. see Table 10C 6 mm2 LABEL [ABEL 00 O00 main earthing metal metal —— earth terminal water a electrode pipe pipe other . extraneous- TT: Earth return via earth electrode conductive- Note: i) Main equipotential bonding conductors may be separate (as shown) or looped with unbroken conductors. parts i) [LABEL |- Safety Electrical Connection - Do Not Remove. £3 iii) An earth electrode resistance exceeding 192 is presumed, see paragraph 4.10. © 5Bw ao Outside Zones: ~ Radiant fire 1. metal waste * Zone | if the space is accessible without the use of a tool. Spaces under the bath, accessible only with the use of a tool, are outside the zones. 2.25m | Outside Zones 7 ' Notes: The protective conductors of all power and lighting points within the zones must be supplementary bonded to all extraneous- conductive-parts in the zones, including metal waste, water and central heating pipes, and metal baths and metal shower basins. . Circuit protective conductors may be used as supplementary bonding conductors.Fig 4e: Supplementary bonding in a bathroom - plastic pipe installation Ceiling Outside Zones 225m : Outside Zones : Notes: 1. The protective conductors of all power and lighting points within the zones must be supplementary bonded. The bonding connection may be to the earth terminal of a switch or accessory supplying equipment. . Circuit protective conductors may be used as supplementary bonding conductors. plastic pipes ? plastic waste ** Zone 1 if the space is accessible without the use of a tool. Spaces under the bath, accessible only with the use of a tool, are outside the zones. yes Le4.8 — Earth Electrode (Fig 4c) This is connected to the main earthing terminal by the earthing 542-01-04 conductor and provides part of the earth fault loop for a TT installation. It is recommended that the earth fault loop impedance for TT 542-02-02 installations does not exceed 200 ohms. Metal gas or water or other metal service pipes are not to be 542-02-04 used as the earth electrode, although they must be bonded as Paragraph 4.1. 49 — Types of Earth Electrode The following types of earth electrode are recognised: ) earth rods or pipes 542-02-01 (ii) earth tapes or wires 542-02-01 (ji) earth plates 542-02-01 (iv) underground structural metalwork embedded in 542-02-01 foundations (v) welded metal reinforcement of concrete embedded in 542-02-01 the earth (excluding pre-stressed concrete) (vi) lead sheaths and metal coverings of cables, which must 542-02-05 meet the following conditions: (a) _ the sheath or covering shall be in effective contact sa202.05(i) with earth, (b) the consent of the owner of the cable shall be 54202-0514) obtained, and (Q arrangements shall be made for the owner of 542-02-05(N) the cable to warn the owner of the electrical installation of any proposed change to the cable or its method of installation which might affect its suitability as an earth electrode. 32 Sec44.10 Typical Earthing Arrangements for Various Types of Earthing System (Figs 4a, 4b, 4c) Figs 4a, 4b and 4c show the single-phase arrangements, but three- phase arrangements are similar. The protective conductor sizes shown in Figures refer to copper Table 54G conductors and are related to 25 mm? supply tails from the Table 54H meter. 547-02-01 For TT systems protected by an RCD with an earth electrode 542-03-01 resistance 1 ohm or greater, the earthing conductor size need 543-01-03 not exceed 2.5 mm? if protected against corrosion by a sheath and if also protected against mechanical damage; otherwise, see Table 10C of Appendix 10. The earthing bar is sometimes used as the main earthing terminal; however, means must be provided in an accessible position for disconnecting the earthing conductor to facilitate 542-04-02 testing of the earthing. Note: For TN-S and TN-C-S installations, advice about the availability of an earthing facility and the precise arrangements for connection should be obtained from the distributor or supplier. 33 Sec4SECTION 5. ISOLATION AND SWITCHING 34 Sec5 5.1 Isolation A means of isolation must be provided to enable electrically 460-01-01 skilled persons to carry out work on, or near, parts which would otherwise normally be energised. Isolating devices must comply with the isolation requirements of BS 1363-4, BS 3676, 511 BS EN 60669-2-4, BS EN 60898, BS EN 60947-2, BS EN 60947-3, 537-02-02 BS EN 61008-1 or BS EN 61009-1. The position of the contacts 537-02-04 must either be externally visible or be clearly, positively and 476-02-02 reliably indicated. If it is installed remotely from the equipment to be isolated, the device must be capable of being secured in the OPEN position. Means of isolation should be provided as follows: (i) at the origin of the installation, a main linked switch or 460-01-02 circuit-breaker should be provided as a means of isolation and of interrupting the supply on load. For single-phase household and similar supplies that may —_476-01-03 be operated by unskilled persons, a double-pole device must be used for both TT and TN systems. For three-phase supplies an isolator must interrupt the phase 460-01-04 and neutral conductors in a TT system; in a TN-S or TN-C-S system only phase conductors need be interrupted. Provision shall be made for disconnecting the neutral —_460-01-06 conductor. Where this is a joint it shall be such that it is accessible, can only be disconnected by means of a tool, is mechanically strong and will reliably maintain electrical continuity (ii) other than at the origin of the installation every circuit, 476-01-02 or group of circuits, which may have to be isolated without interrupting the supply to other circuits should be provided with its own isolating device, which must —_537-02-01 switch all live conductors in a TT system and all phase conductors in a TN system Every motor circuit should be provided with a readily accessible 131-14-02 device to switch off the motor and all associated equipment including any automatic circuit-breaker.5.2 Functional Switching 537-05 A means of switching for interrupting the supply on load is 476-01-02 required for every circuit and final circuit. One common switch may be used to interrupt the supply to a 476-01-01 group of circuits. Additionally, a separate switch must be provided for every circuit which, for safety reasons, has to be 476-01-02 switched independently. 5.3 Switching Off for Mechanical Maintenance 462 A means of switching off for mechanical maintenance is 462-01-01 required where mechanical maintenance may involve a risk of burns or of injury from mechanical movement, and may be required for lamp replacement. Each device for switching off for mechanical maintenance must: i) be capable of switching full load current 537-03-04 (ii) be suitably located in a readily accessible position 462-01-02 (ii) be identified with a permanent label unless its purpose 462-01-02 is obvious (iv) _ have either an externally visible contact gap or a 537-03-02 clearly and reliably indicated OFF position. An indicating light should not be relied upon (v) be selected and installed to prevent unintentional 537-03-03 reclosure, such as might be caused by mechanical shock or vibration. 5.4 Emergency Switching 463 An emergency switch is to be provided for every part of an 476-01-01 installation which may have to be disconnected rapidly from 476-03-04 the supply to prevent or remove danger. Where there is a risk of electric shock the emergency switch is to disconnect all live 463-01-01 conductors, except in three-phase TN-S and TN-C-S systems 460-01-04 where the neutral need not be switched. A means of emergency stopping is also to be provided where 463-01-05 mechanical movement of electrically actuated equipment may 476-03-02 give rise to danger. 35 Sec536 Sec5 A plug and socket-outlet or similar device shall not be selected 537-04-02 as a device for emergency switching. An emergency switch must be: i) readily accessible from the place where the danger 537-04-04 may occur (ii) marked, preferably with a red handle or pushbutton —_537-04-04 (iii) capable of cutting off the full load current 537-04-01 (iv) _ of the latching type or capable of being restrained in 537-04-05 the ‘OFF’ or ‘STOP’ position (vy) double-pole for single-phase systems. 463-01-01 (vi) if operated via a relay or contactor, of adesign which —_537-04-03 has fail-safe characteristics. A fireman's switch must be provided to disconnect the supply to 476-03-05 a high voltage installation, e.g. a neon sign, but such installations are outside the scope of this Guide (see Regulations 476-03-05 to 07 and 537-04-06 of BS 7671). 537-04-06SECTION 6. LABELLING 6.1 Labels to be Provided The following durable labels are to be securely fixed on or adjacent to equipment installed in final circuits. (i) Unexpected presence of nominal voltage (U or Uo) 514-10-01 exceeding 230 V Where the nominal voltage (U or Uo) exceeds 230 V, e.g. 400 V phase-to-phase, and it would not normally be expected to be so high, a warning label stating the maximum voltage present shall be provided where it can be seen before gaining access to live parts. (ii) | Nominal voltage exceeding 230 volts (U or Uo) 514-10-01 between simultaneously accessible equipment For simultaneously accessible equipment with terminals or other fixed live parts having a nominal voltage (U or Uo) exceeding 230 volts between them, e.g. 400 V phase-to- phase, a warning label shall be provided where it can be seen before gaining access to live parts. (iii) Presence of different nominal voltages in the same 514-10-01 equipment Where equipment contains different nominal voltages, e.g. both low and extra-low, a warning label stating the voltages present shall be provided so that it can be seen before gaining access to simultaneously accessible live parts. (iv) Connection of earthing and bonding conductors 514.13, A label to BS 951 durably marked with the words as follows 514-13-01 SAFETY ELECTRICAL CONNECTION - DO NOT REMOVE shall be permanently fixed in a visible position at or near the point of connection of (1) every earthing conductor to an earth electrode or other means of earthing, and (2) every bonding conductor to extraneous- conductive-parts, and (3) at the main earth terminal, where it is not part of the main switchgear. 37 Sec638 Sec6 Ww (vi) (vii) (viii) (ix) Purpose of switchgear and controlgear 514-01-01 Unless there is no possibility of confusion, a label indicating the purpose of each item of switchgear and controlgear shall be fixed on or adjacent to the gear. It may be necessary to label the item controlled, as well as its controlgear. Identification of protective devices 514-08-01 A protective device, e.g. fuse or circuit-breaker, shall be arranged and labelled so that the circuit protected may be easily recognised. Identification of isolators 461-01-05 537-02-09 All isolating devices shall be clearly and durably marked to indicate the circuit or circuits which they isolate. Isolation requiring more than one device 514-11-01 A durable warning notice must be permanently fixed in a clearly visible position to identify the appropriate isolating devices, where equipment or an enclosure contains live parts which cannot be isolated by a single device. Periodic inspection and testing 514-12-01 A notice of durable material indelibly marked with the words as follows, and no smaller than the example shown in BS 7671, IMPORTANT This installation should be periodically inspected and tested and a report on its condition obtained, as prescribed in BS 7671 Requirements for Electrical Installations published by the Institution of Electrical Engineers. Date of last inspection Recommended date of next inspection ... shall be fixed in a prominent position at the origin of every installation. The electrician carrying out the initial(x) The verification must complete the notice, and it must be updated after each periodic inspection. Diagrams 514.09 A diagram, chart or schedule shall be provided showing: (a) the number of points, size and type of cables for each circuit (b) the method of providing protection against indirect contact (©) any circuit vulnerable to an insulation test. schedules of test results (Form F4) of Appendix 7 meets the above requirement for a schedule. (xi) (xii) Residual current devices 514-12-02 Where an installation incorporates an RCD a notice with the words as follows, and no smaller than the example shown in BS 7671, This installation, or part of it, is protected by a device which automatically switches off the supply if an earth fault develops. Test quarterly by pressing the button marked 'T' or ‘Test’. The device should switch off the supply and should then be switched on to restore the supply. if the device does not switch off the supply when the button is pressed, seek expert advice. shall be fixed in a prominent position at or near the origin of the installation. Warning notice - non-standard colours 514-14-01 if alterations or additions are made to an installation so that some of the wiring complies with the harmonized colours of Table 11A and there is also wiring in the old colours, a warning notice shall be affixed at or near the appropriate distribution board with the following wording: CAUTION This installation has wiring colours to two versions of BS 7671. Great care should be taken before undertaking extension, alteration or repair that all conductors are correctly identified. 39 Sec6SECTION 7. FINAL CIRCUITS 7.1 Final Circuits 413-02-08 413-02-12 Table 7.1 has been designed to enable a radial or ring final 525-01-02 circuit to be installed without calculation where the supply is 543-01-03 at 230 V single-phase or 400 V three-phase. For other voltages, App 4 the maximum circuit length given in the table must be Table 4D2A corrected by the application of the formula Table 4D2B Lix Uo Lp= asa 7 230 where: Lp is the permitted length for voltage Uo, Lt is the tabulated length for 230 V Uo is the supply voltage. The conditions assumed are that: (i) the installation is supplied (a) bya TN-C-S system with a maximum external earth fault loop impedance, Ze, of 0.35 ohm, or (b) bya TN-S system with a maximum Ze of 0.8 ohm, or () a TT system with RCDs installed as described in Section 3.6. (ii) the final circuit is connected to a distribution board or consumer unit at the origin of the installation (iii) the method of installation complies with Reference App 4 Methods 1, 3 or 6 of Appendix 4 of BS 7671: (a) Reference Method 1 (M1) Sheathed cables, armoured or unarmoured clipped direct or embedded in plaster (b) Reference Method 3 (M3) Cables run in conduit or trunking Single-core or insulated and sheathed (c) Reference Method 6 (M6) Multicore thermoplastic (pvc) insulated and sheathed — Table 4D54 flat twin cable with protective conductor in conduit in an insulating wall and also direct in a thermally(iv) w) (vi) 7.2 7.21 (i) i) (ii) insulating wall, or single-core thermoplastic (pvc) insulated cables enclosed in conduit in a thermally insulating wall (Method 15). the ambient temperature throughout the length of the Table 4¢1 circuit does not exceed 30 °C the characteristics of protective devices are in App 3 accordance with Appendix 3 of BS 7671, with a fault current tripping time for circuit-breakers of 0.1 s or less the cable conductors are of copper. Using the Tabulated Final Circuits Grouping of Cables In domestic premises, except for heating cables, the Table 4B1 conventional circuit design permits any number of single-layer circuits when the spacing between adjacent surfaces of the cables exceeds one cable diameter, and, for other than semi-enclosed fuses, (BS 3036) up to 5 touching, single-layer, circuits, when clipped to a non-metallic surface (Installation Method 1) up to four, 5 Aor 6 A circuits of enclosed or bunched Table 481 cables (Methods 3 and 6) are allowed for circuits protected by semi-enclosed fuses to BS 3036 and up to 6 circuits when protected by BS 88 or BS 1361 fuses or by circuit-breakers to BS 3871-1 or BS EN 60898 or RCBOs to BS EN 61009 for other groupings and/or high ambient temperatures and/or enclosure in thermal insulation cable sizes will need to be increased per Appendix 6 of this Guide. 41 Sec?£225 TABLE 7.1 Conventional Circuits Device | Cablesize | Protective Cable Maximum length in metres rating | mm? device type Installation a Phase/cpe | (note v) method Ze <0.8 ohm Ze $0.35 ohm (note i) TNS TN-C-S Ithermo- | thermo- 04s 5s 04s 5s plastic(pvd| setting | disconnection] disconnection] disconnection] disconnection cable cable Ring Circuits 30 251.5 BS 1361 M6 M6 90(ii) Nt 90 Ni BS 3036 M1 M3 uv) Nt 91 Ni ch Type 2 M6 M6 5a(ii) Nt 88 Ni cb/RCBO Type 1 &B M6 M6 88 Nt 88 Nt cb/RCBO Type 3 & C M6 M6 N2 Nt Tei) Ni 32 251.5 BS 88 M6 M6 66(vi) Nt 6 Nt cb/RCBO Type 1 &B M6 M6 a4 NI 84 Nt cb Type M6 M6 46(ii) Nt 84 Nt cb/RCBO Type 3 & C M6 M6 N2 NI 68tii) Nt Radial Gircuits 5 1.0/1.0 BS 1361, BS 3036 M6 M6 46 46 46 46 bRCBO Type 1, 2,3,B&C | M6 Me 46 46 6 46 5 1.5/1.0 BS 1361, BS 3036 M6 M6 71 71 7 7m cb/RCBO Type 1, 2,3,B&C | M6 M6 n n nm n 6 1.0/1.0 BS 88 M6 Me 38 38 38 38 Cb/RCBO Type 1, 2,3,B&C | M6 M6 38 38 38 38 cb/RCBO Type D M6 M6 27(ii) 27) 3a(il) 3a(ii)£295 TABLE 7.1 continued Conventional Circuits Cable size | Protective Cable Maximum length in metres rating | mm? device type Installation 7 Phase/cpe | (note v) method Ze<0.8ohm Ze $0.35 ohm (note i) TNS TN-CS Ithermo- | thermo- 04s 5s 04s 5s plastic (pve)| setting | disconnection] disconnection] disconnection] disconnection cable cable Radial Circuits 6 1.5/1.0 BS 88 Ms Ms 59 59 59 59 cb/RCBO Type 1, 2, 3,B&C | M6 M6 59 59 59 59 cb/RCBO Type D M6 Ms fi 45tii) 10 1.0/1.0 BS 88 M6 M6 a cb/RCBO Type 1, 2, 3,B &C | M6 Ms 21 cb/RCBO Type D M6 M6 200i) 10 1.5/1.0 BS 88 Ms M6 33 cb/RCBO Type 1, 2, 3,B&C | M6 M6 33 cb/RCBO Type D M6 M6 23(ii) 15 25/15 BS 3036 M3 M6 35 cb/RCBO Type 1, 2 &B M6 M6 35 cb/RCBO Type 3 & C M6 M6 35 5 4.015 Bs 3036 ms Ms 61 BS 1361 cb/RCBO Type 1, 2 & B 61 cb/RCBO Type 3 & C 61(ii) 16 2.5/1.5 BS 88 33 BS 1361 cb/RCBO Type 1, 2 & 33 cb/RCBO Type 3. & C 33 cb/RCBO Type D 171)nal Circuits Device | Cablesize | Protective Cable Maximum length in metres rating | mm? device type Installation a Phase/cpe | (note v) method Ze< 0.8 ohm Ze 0.35 ohm (note i) TNS TN-CS thermo- | thermo- 04s 5s 04s 5s plastic (pvo)] setting —_| disconnection| disconnection| disconnection] disconnection cable cable Radial Greuits 16 40.5 BS 88 M6 M6 56 56 56 56 cb/RCBO Type 1, 2 &B M6 M6 56 56 56 56 cb/RCBO Type 3 & C M6 M6 34(ii) 34Gii) 56(ii) 46(i1) cb/RCBO Type D M6 M6 N2 N2 20(ii) 20) 20 251.5 BS 88, BS 1361 M3 M6 27 27 27 27 BS 3036 M3 M3 NB NB NB NB cb/RCBO Type 1, 2&B M3 M6 7 27 27 27 cb/RCBO Type 3 & C M3 M6 174i) 174i) 27 27 cb/RCBO Type D M6 M6 N2 2 to(il) 10(ii) 20 4.01.5 BS 3036 m3 M6 43 43 43 43 BS 88, BS 1361 M6 M6 43 43 43 43 cb/RCBO Type 1& B M6 M6 43 43 43 43 ch Type 2 M6 M6 4B 4B 43 43 cbIRCBO Type 3 & C M6 M6 19 19 434i) 42{ii) cb/RCBO Type D M6 M6 N2 N2 12 12 25 4025 BS 88 M6 M6 33 33 33 cb/RCBO Type 1, 2&B M6 M6 33 33 33 cb/RCBO Type 3 & C M6 M6 110i) 11) 33 cb/RCBO Type D M6 Me N2 N2 sui)£25 sv TABLE 7.1 continued Conventional Circuits Device | Cable size | Protective Cable Maximum length in metres rating | mm’ device type Installation A Phase/cpe | (note v) method Ze $0.8 ohm Ze < 0.35 ohm (note i) ‘TN-S TN-C-S thermo- | thermo- 0.45 5s 0.45 55 plastic (pvc)| setting | disconnection] disconnection] disconnection} disconnection cable cable Radial Circuits 25 401.5 BS 88 M6 Me 33 33 33 cb/RCBO Type 1 &B M6 M6 33 33 33 cb Type 2 M6 M6 2a(ii) 33 33 cb/RCBO Type 3 & C M6 Me ati’) 30(ii) 30(ii) cb/RCBO Type D M6 M6 N2 N2 N2 30 6.02.5 BS 3036 M1 M6 27(ii) 45 45 45 BS 1361 M6 M6 31(ii) 42 42 42 cb/RCBO Type 1 &B M6 M6 42 42 42 42 cb Type 2 M6 M6 2x) 27K) 42 “2 cb/RCBO Type 3 & C M6 M6 N2 N2 35(ii) 35(ii) 30 10.0/4.0 | BS 3036 M6 Me ati) 74 14 74 BS 1361 M6 M6 51(ii) 74 74 74 cb/RCBO Type 1 &B M6 M6 74 74 74 74 cb Type 2 M6 M6 alii) 4a(ii) 74 74 cb/RCBO Type 3 & C M6 Me N2 N2 saci) 5a(ii) 32 6.025 BS 88 M6 Me 23(ii) 39 39 39 cb/RCBO Type 1 &B M6 M6 39 39 39 39 cb Type 2 M6 M6 214i) 21) 39 39 cb/RCBO Type 3 & C M6 M6 N2 N2 31(ii) 31Gii) cb/RCBO Type D M6 Me N2 N2 2Gii) ati)£20s TABLE 7.1 continued Conventional Circuits Cable size | Protective Cable Maximum length in metres mm? device type installation Phase/cpc | (note v) method Ze<0.8 ohm Ze< 0.35 ohm (note) TN-S TN-CS thermo- | thermo- 0.45 5s 045 5s plastic (pvc)| setting | disconnection] disconnection] disconnection] disconnection cable cable Radial Circuits 32 10.0/4.0 | BS 88 M6 M6 37(ii) 69 69 69 cb/RCBO Type 1 &B M6 M6 69 69 69 69 cb Type 2 M6 M6 35(il) 35(ii) 69 69 cb/RCBO Type 3 &C M6 M6 N2 N2 51(ii) 51Gii) 40 10.0/4.0 | BS8B M6 M6 7Gi) 53 53 53 cb Type 1 M6 M6 53 53 53 53 cb/RCBO Type B M6 M6 51(ii) 51(ii) 53 53 cb Type 2 M6 M6 Ei) 7Gi) 53 53 cbIRCBO Type 3 &C M6 M6 N2 N2 232(ii) 32(ii) 40 16.0/6.0 | BS 88 M6 M6 11(ii) 88 88 88 cb Type 1 M6 M6 88 88 88 88 cb/RCBO Type B M6 M6 7a(ii) 78(ii) 88 88 ch Type 2 M6 M6 11) 114i) 88 88 cb/RCBO Type 3 & C M6 M6 N2 2 49(ii) 49(ii) 45 10/4.0 BS 1361 M3 M6 N2 104i) 32tii) 49 BS 3036 M1 M3 N2 49 34(ii) 49 cb/RCBO Type 1 &B M3 M6 49 49 49 49 cb/RCBO Type B MB M6 35(i) 35(i) 49 49 cb Type 2 M3 M6 N2 N2 49 49 cbIRCBO Type 3 & C M3 M6 N2 N2 23(i) 23(i)Notes to Table 7.1 (i) _ Installation reference method M6 indicates methods of cable installation M1, M3 and M6 may be used M3 indicates methods of cable installation M1 and M3 may be used M1 indicates method of cable installation M1 only may be used All the circuits are limited by voltage drop other than those marked as below: (ii) Length is limited by earth fault loop impedance (iii) Alternative method of Regulation 413-02-12 applied, 413-02-12 R2 +4 to be less than 0.30 ohm (iv) Alternative method of Regulation 413-02-12 applied, 413-02-12 R2 +4 to be less than 0.36 ohm (vy) Application of RCBOs, see 3.6.3 (vi) Alternative method of Regulation 413-02-12 applied, 413-02-12 R2 +4 to be less than 0.28 ohm N1 NOT PERMISSIBLE as 0.4 s disconnection required for socket-outlet circuits N2 NOT PERMISSIBLE as earth fault loop impedance too high N3 NOT PERMISSIBLE cable overloaded If the alternative method ((iii) or (iv)) is used, R2 must be recorded on the installation schedule. Reference to BS 88 fuses is to BS 88-2.1 or BS 88-6 BS 88 fuses are not available in Consumer Units. 47 Sec77.2.2. Thermosetting cables (e.g. to BS 5467 or BS 7211) Table 4A2 Cable sizes must not be reduced when cables with thermosetting insulation are used, as the cable operating temperature may exceed the maximum tolerated by the accessory to which it is connected. 7.2.3 Checklist Before installing a conventional final circuit the following questions must be answered: (i) (ii) (iii) (iv) (v) (vi) (vii) (viii) (ix) (x) what is the load current and can the distribution board and supply arrangements accommodate it? (See Appendix 1 for guidance on assessing load currents) which kind of protective device is to be used? what cable type and installation method are to be used? what rating of the protective device is equal to or next higher than the load current of the circuit? which type of earthing arrangement is employed? is the maximum required disconnection time 0.4 s or 5 s? Maximum 0.4 s disconnection time is required for circuits 413-02-09 feeding socket-outlets and circuits feeding fixed 471-08-03 equipment outside the equipotential zone. what are the isolation and switching requirements? (See Section 5) what labels are required? (See Section 6) is the earth loop impedance value below the values given in 7.1(i) or 7.2.4(ii)? is an RCD or RCBO required? All socket-outlets on a TT 471-08-06 system must be protected by an RCD or RCBO. Socket-outlets in all systems, that may reasonably be 471-16-01 expected to supply equipment outdoors need to be protected by an RCD or RCBO with a rated residual operating current of 30 mA (all RCDs or RCBOs to comply with BS 4293, BS 7288, BS EN 61008 or BS EN 61009). Certain equipment in bathrooms requires RCD protection. 601-09-02 601-09-037.2.4 TT Systems For TT systems the figures for TN-C-S systems, with 5 s disconnection time, may be used provided that: 10) (ii) iii) the circuit is controlled by an RCD to BS 4293, BS EN 61008 or BS EN 61009 with a rated residual operating current not exceeding 200 mA, and the total earth fault loop impedance is verified as being less than 200 ohms, and a device giving both overload and short-circuit protection is installed in the circuit. This may be an RCBO. 7.2.5 Choice of Protective Device The selection of protective device depends upon: (i) (ii) (ii) (iv) prospective fault current circuit load characteristics cable current-carrying capacity disconnection time limit. Whilst these factors have generally been allowed for in the conventional final circuits in Table 7.1, the following additional guidance is given: (i) prospective fault current If a protective device is to operate safely its rated short- 434-03-01 circuit capacity must exceed the prospective fault current at the point it is installed. At the origin of the installation the distributor needs to 313-01-01 be consulted as to the prospective fault current. Except for London and some other major city centres, the maximum fault current for 230 V single-phase supplies up to 100 A will not exceed 16 kA. Consumer units including protective devices complying as a whole assembly with BS 5486-13 or BS EN 60439-3 are suitable for locations with fault currents up to 16 kA. when supplied through a type II fuse to BS 1361 : 1971 (1992) rated at no more than 100 A. 49 Sec750 Sec7 TABLE 7.2A Rated Short-Circuit Capacities Device type Device Rated designation | short-circuit capacity kA Semi-enclosed fuse to BS 3036 sia 1 with category of duty S2A, 2 saa, 4 Cartridge fuse to BS 1361 type! 16.5 type Il 33.0 General purpose fuse to BS 88-2.1 50 at 415V General purpose fuse to BS 88-6 16.5 at 240 V 80 at 415V Circuit-breakers to BS 3871 M1 1 (replaced by BS EN 60898) M15 15 M3 3 M45, 45 M6 6 M9 9 Circuit-breakers to BS EN 60898* and In kes RCBOs to BS EN 61009 (15) * Two rated short-circuit rating are defined in BS EN 60898 and BS EN 61009 @ en the rated short-circuit capacity (marked on the device). (b) ——cs_the service short-circuit capacity. The difference between the two is the condition of the circuit -breaker after manufacturer's testing. len is the maximum fault current the breaker can interrupt safely, although the breaker may no longer be usable. Ics is the maximum fault current the breaker can interrupt safely without loss of performance. The Icn value is normally marked on the device ina rectangle e. and for the majority of applications the prospective fault current at the terminals of the circut-breaker should not exceed this value. For domestic installations the prospective fault currents unlikely to exceed 6 kA up to which value the lon and Ics values are the same. ‘The short-circuit capacity of devices to BS EN 60947-2 is as specified by the manufacturer.(i) circuit load characteristics (a) _ semi-enclosed fuses - fuses should preferably be of the 533-01-04 cartridge type. Semi-enclosed fuses are still commonly used in domestic and similar premises only (b) cartridge fuses to BS 1361 - these are for use in domestic and similar premises © cartridge fuses to BS 88 - three types are specified: gG_ fuse links with a full-range breaking capacity for general application gM __ fuse links with a full-range breaking capacity for the protection of motor circuits aM fuse links with partial range breaking capacity for the protection of motor circuits. (d) __circuit-breakers to BS 3871-1 or BS EN 60898 and RCBOs to BS EN 61009 - guidance on the selection is given in Table 7.2B below. TABLE 7.2B Instantaneous Application trip current 2.7 t0 4 In domestic and commercial installations 3to5In having little or no switching surge 4.0 to7.0 In general use in commercial/industrial 5to 10 I, installations where the use of fluorescent 7 to 10 In lighting, small motors etc can produce switching surges that would operate a Type 1 or B circuit-breaker. Type C or 3 may be necessary in highly inductive circuits such as banks of fluorescent lighting 10 to 50 In suitable for transformers X-ray machines, 10 to 20 In, industrial welding equipment etc where high inrush currents may occur Where In is the nominal rating of the device. 51 Sec752 Sec7 (ii) cable current-carrying capacities For guidance on the co-ordination of device and cable App 3 ratings see Appendix 6 App 4 (iv) disconnection times 413-02-09 413-02-13 The protective device must operate within 0.4 or 5 seconds as appropriate for the circuit. Appendix 2 provides maximum permissible measured earth fault loop impedances for fuses, circuit-breakers and RCBOs. 7.3 Installation Considerations 7.3.1 Floors and ceilings When a cable is installed under a floor or above a ceiling it shall be 522-06-05 run in such a position that it is not liable to damage by contact with the floor or ceiling or their fixings. Unarmoured cables passing ‘through a joist shall be at least 50 mm from the top or bottom as appropriate or enclosed in earthed steel conduit. Alternatively, the cables can be provided with mechanical protection sufficient to prevent penetration of the cable by nails, screws and the like. (Note, ‘the requirement to prevent penetration is difficult to meet.) Fig 7.3.1: Cables through joists cable in earthed insulated steel conduit and sheathed ¥ cable greater than 50 mm Notes: Maximum diameter of hole should be 0.25 x joist depth. Holes on centre line in a zone between 0.25 and 0.4 x span. Maximum depth of notch should be 0.125 x joist depth. Notches on top in a zone between 0.1 and 0.25 x span. pe wn sn Holes in the same joist should be at least 3 diameters apart.73.2 Walls Where a cable is concealed in a wall or partition at a depth of less 522-06-06 than 50 mm from any surface it must be enclosed in earthed metal conduit (trunking or ducting) or installed either horizontally within 150 mm of the top of the wall or partition or vertically within 150 mm of the angle formed by two walls, or run horizontally or vertically to an accessory or consumer unit (see Fig 7.3.2). Fig 7.3.2: Permitted cable routes no protection required 150mm wall <4— protection required unless depth greater than 50 mm Note: A Zone formed on one side of a partition wall of 100 mm or less thickness 5 22-06-06 extends to the reverse side only if the location of the accessory can be determined from the reverse side. 7.3.3 Telecommunication Circuits 528-01-02 528-01-04 An adequate separation between telecommunication wiring (Band |) and electric power and lighting (Band II) circuits must be maintained. This is to prevent mains voltage appearing in telecommunication circuits with consequent danger to personnel. BS 6701: 1994 recommends that the minimum separation distances given in Tables 7.3A and 7.3B should be maintained: 53 Sec754 Sec7 TABLE 7.3A External Cables Minimum separation distances between external low voltage electricity supply cables operating in excess of 50 V a.c. or 120 V d. to earth, but not exceeding 600 V a.c. or 900 V d.c. to earth (Band Il), and Telecommunications cables (Band 1). Voltage to earth Normal separation distances Exceeding 50 V a.c. or 120 V d.c., but not 50mm Exceptions to normal separation distances, plus conditions to exception Below this figure a non-conducting divider should be inserted between exceeding 600 V a.c. or 900 V d.c. the cables, TABLE 7.3B Internal Cables Minimum separation distances between internal low voltage electricity supply cables operating in excess of 50 V a.c. or 120 V dic. to earth, but not exceeding 600 V a.c. or 900 V d.c. to earth (Band II) and Telecommunications cables (Band I). Voltage to earth Normal separation distances Exceptions to normal separation distances, plus conditions to exception Exceeding 50 V ac, or 120 V d.c., but not exceeding 600 V a.c. or 900 V dic. 50 mm separation need not be maintained, provided that ()_ the LV cables are enclosed in separate conduit which if metallic is earthed in accordance with BS 7671, OR the LV cables are enclosed in separate trunking which if metallic is earthed in accordance with BS 7671, OR ii) the LV cable is of the mineral insulated type or is of earthed armoured construction 1. Where the LV cables share the same tray then the normal separation should be met. 2. Where LV and telecommunications cables are obliged to cross additional insulation should be provided at the crossing point; this is not necessary if either cable is armoured.7.3.4 Proximity to Other Systems 528-02 Electrical and all other services must be protected from any harmful mutual effects foreseen as likely under conditions of normal service. For example, cables should not be in contact 528-02-02 with or run alongside hot pipes. The installation must comply with BS 7671, Chapter 52 and Chapter 54, regarding separation and bonding. A particular form of harmful effect may occur when an electrical installation shares the space occupied by a hearing aid induction loop. Under these circumstances, if phase(s) and neutral or switch feeds and switch wires are not close together, there may be interference with the induction loop. This can occur when a conventional two-way circuit is installed. This effect can be reduced by connecting as shown in Fig 7.3.4. Fig 7.3.4: Circuit for reducing interference with induction loop neutral a witch wire light point A 2 way switch ‘common cores q grouped together | strappers 2 way switch circuit shown switched of 55 Sec756 Sec? 7.3.5 Height of switches, sockets etc Accessories for general use, such as light switches and socket- outlets, are required by the Building Regulations to be located so that they can be used by people whose reach is limited. A way of satisfying this requirement is to install switches for lights and similar equipment and socket-outlets 553-01-06 at a height of between 450 mm and 1200 mm from finished floor level. See Figure 8A in Appendix 8. 7.4 Smoke Alarms and Emergency Lighting 7.4.1. Smoke alarms in single dwellings The Building Regulations 1991 and the Building Standards (Scotland) Regulations 1990 require all new and refurbished dwellings to be fitted with mains operated smoke alarms, The requirements for single family dwellings of not more than two storeys are that self-contained smoke alarms should be installed as follows: 1) at least one on each floor 2) within 7 m of kitchens and living rooms or other areas where fires may start e.g. integral garages 3) within 3 m of all bedroom doors. The smoke alarm must be installed in accordance with the manufacturer's instructions, generally on ceilings and at least 300 mm from any wall or ceiling luminaire. The alarms are required to:- - be interconnected so that detection of smoke by one unit operates the alarm in all units - be permanently wired to a separate way in the distribution board (consumer unit), or supplied from a local, regularly used lighting circuit. - have battery backup Except for TT supplies, the circuit supplying a smoke alarm should not be protected by an RCD. For TT supplies the smoke alarm must be supplied from the fixed equipment section, that is not through a 30 mA RCD, see Figure 3a.The cable for the power supply to each self-contained unit and for the interconnections need have no fire retardant properties, and needs no special segregation. Otherwise, fire 528-01-04 alarm system cables generally are required to be segregated as per BS 5839-1 and BS 5839-6, see Table 7.4. TABLE 7.4 Segregation requirements of fire alarm and emergency lighting standards Fire alarms Emergency lighting BS 5839 BS 5266, a _ installation in conduit, ducting, trunking or achannel_ a _physical segregation by a reserved for fire alarms, or minimum distance of 300 mm, or b amechanically strong, rigid and continuous partition of non-combustible material, or use of mineral cables, or ¢ mounting at a distance of at least 300 mm from ¢ cables to BS 6387 Cat B conductors of other systems, or d__ wiring in cables complying with BS 7629, or wiring in mineral insulated copper sheathed cable with an insulating sheath or barrier. The exposed-to- Table 1A touch rating of the IEE Wiring Regulations should not he exceeded. 7.4.2 Emergency lighting The wiring to self-contained emergency lighting luminaires is not considered part of the emergency lighting installation and needs no special segregation. Otherwise, emergency lighting 528-01-04 and fire alarm circuits must be separated from other cables and from each other, in compliance with BS 5266, see Table 7.4. 57 Sec7SECTION 8. SPECIAL LOCATIONS GIVING RISE TO INCREASED 58 Secs RISK OF ELECTRIC SHOCK 8.1 Locations Containing a Bath or Shower 8.1.1 Because of the presence of water these locations are onerous for equipment and there is an increased danger of electric shock because of immersion of the body in water. The additional requirements can be summarised as follows: (i) No socket-outlets are allowed other than SELV and shaver supply units - see Table 8.1. (ii) Supplementary bonding of the terminals of the protective conductors of circuits to Class | and Class II equipment in the zones (see Figure 4d) to exposed- conductive-parts in the zones is required, including: - metal pipes both water and central heating - metal baths and shower basins - accessible metal structural parts of the building. The supplementary bonding must be carried out in or in close proximity to the zones. See Figures 4d and 4e. (iii) Protection against ingress of moisture is specified for equipment installed in the zones — see figure 4d and Table 8.1. The requirements apply to appliances, switchgear and wiring accessories. (iv) There are restrictions as to where appliances, switchgear and wiring accessories may be installed - see 601-09 Table 8.1. 8.1.2 Underfloor heating installations in these areas should 601-09-04 have an overall earthed metallic grid or the heating cable should have an earthed metallic sheath, which must be supplementary bonded.TABLE 8.1 Requirements for equipment (current using and accessories) in locations containing a bath or shower Zone Requirements for equipment in the zones note2 | Minimum Current Using (Appliances) Switchgear and Accessories degree of protection 0 1PX7__| Only SELV fixed equipment that cannot be located elsewhere, |None allowed. 7 1PX4___|SELV equipment allowed. Only 12 Va.c. and 30 V dc. switches of SELV circuits Water heaters, showers, shower pumps, allowed. allowed, the source being outside zones 0, 1 and 2. Other fixed equipment that cannot reasonably be located elsewhere allowed if protected by a 30 mA RCD. 2 1PX4__|SELV equipment allowed. ISELV switches and sockets allowed, the source being Water heaters, showers, shower pumps, luminaires, fans, | OUtside zones 0, 1 and 2, and shaver supply units to heating appliances, units for whirlpool baths allowed. bay om ia 2 i 1 allowed only if fixed where m ; Other fixed equipment that cannot reasonably be located Fee eee elsewhere allowed. 3 No |SELV equipment allowed. Accessories allowed except for socket-outlets. There is requirement. | appliances allowed and, unless fixed, must be protected _|t© be no provision for connecting portable equipment. by a 30 mA ROD. SELV sockets and shaver supply units to BS EN 60742 Chap 2 Sect 1 allowed. Outside|__No_ [Appliances allowed ‘Accessories allowed except for socket-outlets. Zones | requirement. SELV sockets and shaver supply units to BS EN 60742 Chap 2 Sect 1 allowed. 6S 820s Note 1: Where a shower cubicle is installed in a room other than a bathroom or shower room, outside zones 0, 1, 2 or 3 a socket- outlet, other than a SELV socket-outlet or shaver supply unit, shall be protected by a residual current device with rated residual operating current (Ign) not exceeding 30 mA in accordance with Regulation 412-06. Note 2: See Figures 4d and 4e for zones. 601-08-01 601-09-01 601-08-01 601-09-01 601-08-01 601-09-03 601-08-01 601-09-03 601-08-01 6601-08-02 412-0660 Sec8 8.2 Shower Cubicles in a Room used for Other Purposes —_601-08-02 Where a shower cubicle is installed in a room other than a bathroom or shower room the requirements for bathrooms and shower rooms are generally to be complied with, except that socket-outlets are allowed outside zones 0, 1, 2 and 3 provided they are protected by a 30 mA RCD, and no supplementary bonding is required in zone 3. 601-04-02 8.3 Temporary and Garden Buildings, Domestic Garages, 300-01 Buildings of Lightweight Construction etc The use of a temporary building does not permit a lower standard of electrical installation. The standards of installation and maintenance need to be higher to cope with the more onerous conditions. Particular attention must be paid to: i) suitability of the equipment for the environment (ii) earthing and bonding (iii) connection to the supply (iv) _ use of accessories of the appropriate Degree of Protection (IP code) to suit the particular external influences. 84 — Earthing requirements of Equipment having High 607 Protective Conductor Current Equipment Equipment having a protective conductor current exceeding 607-02-02 3.5 mA shall be either permanently connected to the fixed wiring or connected by means of an industrial plug and socket to BS EN 60309-2. Equipment having a protective conductor current exceeding 6907-02-03 10 mA shall be connected preferably by a permanent connection, or an industrial plug and socket to BS EN 60309-2 with a protective conductor csa of at least 2.5 mm? for plugs up to 16 A and at least 4 mm? for plugs rated above to 16 A. Circuits The wiring of every final circuit and distribution circuit having 607-02-04 a protective conductor current likely to exceed 10 mA shall have high integrity protective conductor connections comprising either: (i) a single protective conductor complying with Section 543 and of csa not less than 10 mm2, or(ii) a single copper protective conductor complying with Section 543 and of csa not less than 4 mm? enclosed in conduit, or (iii) duplicate protective conductors, each complying with Section 543. Socket-outlet final circuits For socket-outlet final circuits requiring a high integrity protective 607-03-01 conductor connection, the following arrangements are acceptable: (i) aring circuit with a ring protective conductor (Fig 8.4a), or (ii) a radial circuit with a single protective conductor (Fig 8.4b) connected as a ring or an additional protective conductor provided by conduit, trunking or ducting. When the two protective conductors are provided the ends must be terminated independently of each other at all connection points e.g. distribution board and socket-outlet. Accessories are required to have two separate earth terminals. Fig 8.4a: Ring final circuit supplying socket-outlets DISTRIBUTION BOARD (total protective conductor current exceeding 10 mA) separate connections 0, Socket-outlets must have two terminals for protective conductor, One terminal to be used for each protective conductor, of a minimum size of 15 mm? Fig 8.4b: Radial circuit supplying socket-outlets with duplicate protective conductor DISTRIBUTION BOARD| «(total protective conductor current exceeding 10 mA) separate connections Socket-outlets must have two terminals for protective conductors. Duplicate protective conductor. (One terminal to be used for each Keep close to circuit conductors protective conductor, of a minimum to reduce eme effects. Size of 15 mm?62 Sec9 SECTION 9. INSPECTION AND TESTING Part 7 9.1 Inspection and Testing Every installation must be inspected and tested during erection 711-01-01 and on completion before being put into service. Precautions shall be taken to avoid danger to persons and to 711-01-01 avoid damage to property and installed equipment during inspection and testing. If the inspection and tests are satisfactory, a signed Electrical 741 Installation Certificate together with a Schedule of Inspections and a Schedule of Test Results (as in Appendix 7) are to be given to the person ordering the work. 9.2 Inspection 9.2.1 Procedure and Purpose Inspection shall precede testing and shall normally be done 712-01-01 with that part of the installation under inspection disconnected from the supply. The purpose of the inspection is to verify that equipment is: 712-01-02 (i) correctly selected and erected in accordance with BS 7671 (and if appropriate its own standard) (ii) not visibly damaged or defective so as to impair safety. 9.2.2 Inspection Checklist 712-01-03 The inspection shall include at least the checking of relevant items from the following checklist: i) connection of conductors (i) identification of conductors (iii) routing of cables in safe zones or protected against mechanical damage (iv) _ selection of conductors for current-carrying capacity and voltage drop, in accordance with the design (v) connection of single-pole devices for protection or switching in phase conductors only(vi) (vii) (iii) (ix) correct connection of accessories and equipment (including polarity) presence of fire barriers, suitable seals and protection against thermal effects methods of protection against electric shock (a) protection against both direct contact and indirect contact, i-e.: - SELV - limitation of discharge of energy (b) protection against direct contact (including measurement of distances where appropriate), Le: - protection by insulation of live parts - protection by barriers or enclosure - protection by PELV (c) _ protection against indirect contact: + earthed equipotential bonding and automatic disconnection of supply presence of earthing conductor presence of protective conductors presence of main equipotential bonding conductors presence of supplementary equipotential bonding conductors - _ use of Class Il equipment or equivalent insulation - electrical separation prevention of mutual detrimental influence 515 Account must be taken of the proximity of other 528 electrical services of a different voltage band and of non-electrical services and influences. Fire alarm and emergency lighting circuits must be 528-01-04 separated from other cables and from each other, in compliance with BS 5839 and BS 5266, see 7.4.1 and 74.2. 63 Sec9Sec () (xi) (xii) (xiii) (xiv) (xv) (xvi) Band | and Band II circuit cables may not be present in the same enclosure or wiring system unless they are either separated by an effective barrier or wired with cables suited to the highest voltage present. Where common boxes are used for Band | and Band II circuits, the circuits must be segregated by an insulating or earthed partition. Mixed categories of circuits may be contained in multicore cables, subject to specific requirements. Definitions of voltage bands Band | circuit: Circuits that are nominally extra-low ie. not exceeding 50 V ac or 120 V dc e.g. SELV, PELV, telecommunications, data and signalling. Band If circuit: Circuits that are nominally low voltage, that is 51 to 1000 V ac and 120 to 1500 V dc. Telecommunication cables that are generally ELV but have ringing voltages exceeding 50 V are Band |. presence of appropriate devices for isolation and switching correctly located presence of undervoltage protective devices (where appropriate) choice and setting of protective and monitoring devices (for protection against indirect contact and/or protection against overcurrent) labelling of circuits, cbs, RCDs, fuses, switches and terminals, main earthing and bonding connections selection of equipment and protective measures appropriate to external influences adequacy of access to switchgear and equipment presence of danger notices and other warning signs (see Section 6) 528-01-02 528-01-07 528-01-02 Part 2 131-14-01 451 514 522(xvii) presence of diagrams, instructions and similar 514-09 information (xviii) erection methods 522 (xix) requirements for special locations. 600 9.3 Testing 713 Testing must include the relevant tests from the following checklist. When a test shows a failure to comply, the installation must be 713-01-01 corrected. The test must then be repeated, as must any earlier test that could have been influenced by the failure. 9.3.1 Testing Checklist (i) continuity of protective conductors {including main and 713-02-01 supplementary equipotential bonding conductors) (ii) continuity of ring final circuit conductors including 713-03-01 protective conductors (iii) insulation resistance (between live conductors and 713-04 between each live conductor and earth) (iv) __ polarity; this includes checks that single-pole control 713-09 and protective devices (e.g. switches, circuit-breakers, fuses) are connected in the phase conductor only, that bayonet and Edison-screw lampholders (except for E14 and E27 to BS EN 60238) have their outer contacts connected to the neutral conductor and that wiring has been correctly connected to socket-outlets and other accessories (v) earth electrode resistance 713-10 (vi) earth fault loop impedance 713-11 (vii) prospective fault current, if not determined by enquiry 713-12 of the distributor (viii) functional testing (including RCDs and RCBOs). 713-13 65 Sec9SECTION 10. GUIDANCE NOTES ON INITIAL TESTING OF INSTALLATIONS 10.1 Safety and equipment 71-01-01 Electrical testing involves danger. It is the tester's duty to ensure his or her own safety, and the safety of others, in the performance of the test procedures. When using test instruments, this is best achieved by precautions such as: (i) an understanding of the correct application and use of the test instrumentation, leads, probes and accessories to be employed (ii) checking that the test instrumentation is made in accordance with the appropriate safety standards such as BS EN 61243-3 for two-pole voltage detectors and BS EN 61010 or BS EN 61557 for instruments (iii) checking before use that all leads, probes, accessories (including all devices such as crocodile clips used to attach conductors) and instruments are clean, undamaged and functioning (iv) observing the safety measures and procedures set out in HSE Guidance Note GS 38 for all instruments, leads, probes and accessories. It should be noted that some test instrument manufacturers advise that their instruments be used in conjunction with fused test leads and probes. Other manufacturers advise the use of non-fused leads and probes when the instrument has in-built electrical protection, but it should be noted that such electrical protection does not extend to the probes and leads. 10.2 Sequence of Tests 73-01-01 Note: The advice given does not preclude other test methods. Tests should be carried out in the following sequence: 10.2.1 Before the supply is connected (i) continuity of protective conductors, induding main and supplementary bonding (ii) continuity of ring final circuit conductors, including protective conductors insulation resistance (iv) __ polarity (by continuity methods) 66 Sec 10(v) earth electrode resistance, when using an earth electrode resistance tester (see also vii). 10.2.2 With the supply connected (vi) re-check of polarity (vii) earth electrode resistance, when using a loop impedance tester (viii) earth fault loop impedance (ix) prospective fault current measurement, if not determined by enquiry of the distributor (x) functional testing. Results obtained during various tests should be recorded in the 741-01-01 Schedule of Test Results (Appendix 7) for future reference. 10.3 Test Procedures 10.3.1 Continuity of protective and bonding conductors (except ring final circuits, see Para 10.3.2) Test Methods 1 and 2 are alternative ways of testing the continuity of protective conductors. Every protective conductor including the earthing conductor, main and supplementary bonding conductors should be tested to verify that the conductors are electrically sound and correctly connected. Test Method 1 detailed below, as well as checking the continuity of the protective conductor, also measures (Ri + R2) which, when added to the external impedance (Ze), enables the earth- fault loop impedance (Zs) to be checked against the design, see Section 10.3.6. Note: (R1 + R2) is the sum of the resistances of the phase conductor (R1) and the circuit protective conductor (R2) between the point of utilisation and origin of the installation. Use an ohmmeter capable of measuring a low resistance for these tests. Test Method 1 can only be used to measure (Ri + R2) for an ‘all insulated’ installation. Installations incorporating steel conduit, steel trunking, micc and pvc/swa cables will produce parallel paths to protective conductors. Such installations should be inspected for soundness of construction and Test Method 1 or 2 used to prove continuity. 7413-02-01 67 Sec 10OL 285 89 Fig 10.1: Connections for testing continuity of protective conductors Method 1 ceiling rose atend of ——> circuit temporary link lamps removed switch on test instrument main switch off distribution board all fuses out or all breakers off10.3.1(i) To test the continuity of protective conductors Test Method 1 Bridge the phase conductor to the protective conductor at the distribution board so as to include all the circuit. Then test between phase and earth terminals at each point in the circuit. The measurement at the circuit’s extremity should be recorded and is the value of (Ri + R2) for the circuit under test (see Fig 10.1). If the instrument does not include an “auto-null” facility, or this is not used, the resistance of the test leads should be measured and deducted from the resistance readings obtained. Test Method 2 Connect one terminal of the continuity test instrument to a long test lead and connect this to the consumer's main earthing terminal. Connect the other terminal of the instrument to another test lead and use this to make contact with the protective conductor at various points on the circuit, such as luminaires, switches, spur outlets etc. The resistance of the protective conductor R2 is recorded on the Schedule of Test Results, form F4. 10.3.1(ii) To test the continuity of bonding conductors Use Test Method 2 10.3.2 Continuity of ring final circuit conductors A three step test is required to verify the continuity of the phase, neutral and protective conductors and correct wiring of every ring final circuit. The test results show if the ring has been inter-connected to create an apparently continuous ring circuit which is in fact broken, or wrongly wired. Step 1: The phase, neutral and protective conductors are identified and the end-to-end resistance of each is measured separately (see Fig10.2a). These resistances are r1, rn and r2 respectively. A finite reading confirms that there is no open circuit on the ring conductors under test. The resistance values obtained should be the same (within 0.05 ohm) if the conductors are the same 713-02-01 713-02-01 713-03-01 69 Sec 1070 Sec 10 size. If the protective conductor has a reduced csa the resistance +2 of the protective conductor loop will be proportionally higher than that of the phase and neutral loops e.g. 1.67 times for 2.5/1.5 mm? cable. If these relationships are not achieved then either the conductors are incorrectly identified or there is something wrong at one or more of the accessories. Step 2: The phase and neutral conductors are then connected together so that the outgoing phase conductor is connected to the returning neutral conductor and vice-versa (see Fig 10.2b). The resistance between phase and neutral conductors is measured at each socket-outlet. The readings at each of the sockets wired into the ring will be substantially the same and the value will be approximately one quarter of the resistance of the phase plus the neutral loop resistances, i.e. (r1 + Mm)/4. Any sockets wired as spurs will have a higher resistance value due to the resistance of the spur conductors. Note: Where single-core cables are used, care should be taken to verify that the phase and neutral conductors of opposite ends of the ring circuit are connected together. An error in this respect will be apparent from the readings taken at the socket-outlets, progressively increasing in value as readings are taken towards the midpoint of the ring, then decreasing again towards the other end of the ring. Step 3: The above step is then repeated, this time with the phase and cpc cross-connected (see Fig 10.2c). The resistance between phase and earth is measured at each socket. The readings obtained at each of the sockets wired into the ring will be substantially the same and the value will be approximately one quarter of the resistance of the phase plus cpc loop resistances, ie. (ry + r2)/4. As before, a higher resistance value will be recorded at any sockets wired as spurs. The highest value recorded represents the maximum (Rj + R2) of the circuit and is recorded on Form F4, The value can be used to determine the earth loop impedance (Zs) of the circuit to verify compliance with the loop impedance requirements of BS 7671 (see Appendix 9). This sequence of tests also verifies the polarity of each socket, except that if the testing has been carried out at the terminals on the reverse of the accessories, a visual inspection is required to confirm correct polarity connections, and dispenses with the need for a separate polarity test.Fig 10.2: Connections for testing continuity of ring final circuit conductors 10.2a initial check for continuity at ends of ring test instrument 10.2¢ 10.2b N LON L connection for taking readings of Ri + R2 at sockets 71 Sec 1072 Sec 10 10.3.3 Insulation resistance Pre-test checks 10.3.3(i) (a) _ pilot or indicator lamps, and capacitors are disconnected from circuits to avoid misleading test values being obtained (b) if a circuit includes voltage-sensitive electronic devices such as dimmer switches, touch switches, delay timers, power controllers, electronic starters or controlgear for fluorescent lamps etc either: (1) _ the devices must be temporarily disconnected, or (2) ameasurement should be made between live conductors (phase and neutral) connected together and the protective earth only It should also be confirmed that there are no RCDs incorporating electronic amplifiers, before the test is made. 10.3.3(ii) Tests should be carried out using the appropriate d.c. test voltage specified in Table 10.1. The tests should be made at each distribution with the main switch off, all fuses in place, switches and circuit-breakers closed, lamps removed and other current-using equipment disconnected. Where the removal of lamps and/or the disconnection of current-using equipment is impracticable, the local switches controlling such lamps and/or equipment should be open.Where any circuits contain two-way switching the two-way switches must be operated one at a time and further insulation resistance tests carried out to ensure that all the circuit wiring is tested. TABLE 10.1 TABLE 71A Minimum values of insulation resistance Circuit nominal Minimum voltage voltage insulation Vdc. resistance (M ohms) SELV and PELV 0.25 Up to and including 500 V with the exception of SELV and PELV, but including FELV Although an insulation resistance value of not less than 0.5 megohm complies with BS 7671, where an insulation resistance of less than 2 megohms is recorded the possibility of a latent defect exists. Each circuit should then be tested separately, and its insulation resistance should be greater than 2 megohms. Where electronic devices are disconnected for the purpose of 713-04-04 the tests on the installation wiring (and the devices have exposed-conductive-parts required by BS 7671 to be connected to the protective conductors) the insulation resistance between the exposed-conductive-parts and all live parts of the device (phase and neutral connected together) should be measured separately and should not be less than the values stated in Table 10.1. 10.3.3(iii) Insulation resistance between live conductors 713-04 Single-phase and three-phase Test between all the live (phase and neutral) conductors at the distribution board (see Fig 10.3). 73 Sec 10OL 285 Fig 10.3: Insulation resistance tests between live conductors of a circuit switch on lamps removed main switch off circuit-fuse out or breakers off note 1: protective conductors to switches have been omitted for clarity note 2: the test should initially be carried out on the complete installation test instrumentResistance readings obtained should be not less than the minimum values referred to in Table 10.1. 10.3.3(iv) Insulation resistance to Earth 713-04 Single-phase Test between the live conductors (phase and neutral) and the circuit protective conductors at the distribution board (see Fig 10.4). For circuits containing two-way switching or two-way and intermediate switching the switches must be operated one at a time and the circuit subjected to additional insulation resistance tests. Three-phase Test to earth from all live conductors (including the neutral) connected together. Where a low reading is obtained it is necessary to test each conductor separately to earth, after disconnecting all equipment. Resistance readings obtained should be not less than the minimum values referred to in Table 10.1. 10.3.3(v) SELV and PELV circuits Table 714 Test between SELV and PELV circuits and live parts of other circuits at 500 V dic. Test between SELV or PELV conductors at 250 V d.c. and between PELV conductors and protective conductors of the PELV circuit at 250 V d.c. 10.3.3(vi) FELV circuits 471-14-03 FELV circuits are tested as LV circuits at 500 V d.c. 75 Sec 10OL es 9L Fig 10.4: Insulation resistance tests to earth ceiling ceiling foPe tl rose \ ge lamps removed = a IT) i LBS d two-way switches a switch on lamps la removed eee distribution board note 1: protective conductors to switches have been omitted for clarity note 2: the test should initially be carried out on the complete installation test instrumentFig 10.5: Polarity test on a lighting circuit R2 i a ae a a ee eee 1 I | Note: | Protective conductor 1 {| to switch has been temporary ‘| omitted for clarity link 1 i Edison screw i lampholder switch if] as oo wee aE EEL loo) main switch off all fuses out or all breakers off distribution board note: the polarity of E14 and E27 Edison screw lampholders to BS EN 60238 does not have to be verified. test instrument Ob 28S ae78 Sec 10 10.3.4 Polarity See Figure 10.5. The method of test prior to connecting the supply is the same as Test Method 1 for checking the continuity of protective conductors which should have already been carried out (see 10.3.1, 10.3.2 and Figs 10.1 and 10.2). For ring circuits a visual check may be required (see 10.3.2 following step 3). It is important to confirm that: (i) overcurrent devices and single-pole controls are in the phase conductor (ii) except for E14 and E27 lampholders to BS EN 60238, centre contact screw lampholders have the outer threaded contact connected to the neutral and (iii) socket polarities are correct. After connection of the supply polarity must be checked using a voltmeter or a test lamp (both with leads complying with HSE Guidance Note GS 38). 10.3.5 Earth Electrode Resistance If the electrode under test is being used in conjunction with an RCD protecting an installation, the following method of test may be applied. A loop impedance tester is connected between the phase conductor at the origin of the installation and the earth electrode with the test link open, and a test performed. This impedance reading is treated as the electrode resistance and is then added to the resistance of the protective conductor for the protected circuits. The test should be carried out before energising the remainder of the installation. The measured resistance should meet the following criteria and those of 10.3.6 but in any case should not exceed 200 ohms: For TT systems, the value of the earth electrode resistance Ra in ohms multiplied by the operating current in amperes of the protective device IAn shall not exceed 50 V e.g. if Ra = 200 Q, then the maximum RCD operating current should not exceed 250 mA. Remember to replace the test link. 713-09 713-09-01 7713-09-01 713-09-01 713-10 542-02-02 413-02-2010.3.6 Earth Fault Loop Impedance 713-11 The earth fault loop impedance (Z;) is required to be 413-02-10 determined for the furthest point of each circuit. It may be 413-02-11 determined 413-02-14 - by direct measurement of Zs. - by direct measurement of Ze at the origin and adding (R1 + R2) measured during the continuity tests (10.3.1 and 10.3.2) (Zs = Ze + (Ri + R2)) - by adding (R1 + R2) measured during the continuity tests to the value of Ze declared by the distributor, (see 7.1(i)). The effectiveness of the distributor's earth must be confirmed by a test. The external impedance (Z.) may be measured using a phase- earth loop impedance tester. The main switch is opened and made secure to disconnect the installation from the source of supply. The earthing conductor is disconnected from the main earthing terminal and the measurement made between phase and earth of the supply. Remember to reconnect the earthing conductor to the earth terminal after the tests. Direct measurement of Z, can only be made on a live installation. Neither the connection with earth nor bonding conductors are disconnected. The reading given by the loop impedance tester will usually be less than Z. + (Ri + R2) because of parallel earth return paths provided by any bonded extraneous-conductive-parts. This must be taken into account when comparing the results with design data. Care should be taken to avoid any shock hazard to the testing personnel and to other persons on site during the tests. The values of Z; determined should be less than the value given 413-02-08 in Appendix 2 for the particular overcurrent device and cable. 543-01-03 For TN systems, when protection is afforded by an rcd, the 413-02-16 rated residual operating current in amperes times the earth fault loop impedance in ohms should not exceed 50 V. This test should be carried out before energising other parts of the system. Note: For further information on the measurement of earth fault loop impedance, refer to Guidance Note No 3 — Inspection and Testing. 79 Sec 1080 Sec 10 10.3.7 Measurement of prospective fault current 713-12-01 lt is not recommended that installation designs are based on 434-02-01 measured values of prospective fault current, as changes to the distribution network subsequent to the completion of the installation may increase fault levels. Designs should be based on the maximum fault current 313-01-01 provided by the distributor (see 7.2.5(i)). If it is desired to measure prospective fault levels this should be done with all main bonding in place. Measurements are made at the distribution board between live conductors and between phase conductors and earth. For three-phase supplies the maximum possible fault level will be approximately twice the single-phase to neutral value. (For three-phase to earth faults, neutral and earth path impedances have no influence.) 10.3.8 Functional testing 713-13 RCDs should be tested as described in Section 11. All assemblies 713-13-02 including switchgear, controls, and interlocks should be functionally tested; that is, operated to check that they work and are properly fixed etc.SECTION 11. OPERATION OF RESIDUAL CURRENT OPERATED DEVICES 11.7 (RCDs) AND RESIDUAL CURRENT BREAKERS WITH OVERCURRENT PROTECTION (RCBOs) General Test Procedure The tests are made on the load side of the RCD, as near as practicable to its point of installation, and between the phase conductor of the protected circuit and the associated circuit protective conductor. The load supplied should be disconnected during the test. 11.2 i) (ii) (i) a) (i) (ii) General purpose RCDs to BS 4293 with a leakage current flowing equivalent to 50 % of the rated tripping current, the device should not open. with a leakage current flowing equivalent to 100 % of the rated tripping current of the RCD, the device should open in less than 200 ms. Where the RCD incorporates an intentional time delay it should trip within a time range from ‘50 % of the rated time delay plus 200 ms’ to ‘100 % of the rated time delay plus 200 ms’. General purpose RCCBs to BS EN 61008 or RCBOs to BS EN 61009 with a leakage current flowing equivalent to 50 % of the rated tripping current of the RCD the device should not open. with a leakage current flowing equivalent to 100 % of the rated tripping current of the RCD, the device should open in less than 300 ms unless it is of ‘Type S’ (or selective) which incorporates an intentional time delay. In this case, it should trip within a time range from 130 ms to 500 ms RCD protected socket-outlets to BS 7288 with a leakage current flowing equivalent to 50 % of the rated tripping current of the RCD the device should not open with a leakage current flowing equivalent to 100 % of the rated tripping current of the RCD, the device should open in less than 200 ms 713-13-01 81 sec1182 Sec11 11.5 Additional Requirement for Supplementary Protection 412-06-02 Where an RCD or RCBO with a rated residual operating current lan not exceeding 30 mA is used to provide supplementary protection against direct contact, with a test current of 5lan the device should open in less than 40 ms. The maximum test time must not be longer than 40 ms, unless the protective conductor potential rises by less than 50 V. (The instrument supplier will advise on compliance). 11.6 Integral Test Device 713-13-02 An integral test device is incorporated in each RCD. This device enables the electrical and mechanical parts of the RCD to be verified, by pressing the button marked ‘T’ or ‘Test’. Operation of the integral test device does not provide a means of checking: (a) _ the continuity of the earthing conductor or the associated circuit protective conductors, or (b) any earth electrode or other means of earthing, or (any other part of the associated installation earthing. The test button will only operate the RCD if the RCD is energised. Confirm that the notice to test RCDs quarterly (by pressing the 514-12-02 test button) is fixed in a prominent position ((see 6.1(xi)).APPENDICES CONTENTS Appendix Page 1 Maximum demand and diversity 84 2. Maximum permissible measured earth fault loop impedance 88 3 Notes on the selection of types of cable and flexible cord for particular uses and external influences 94 4 Notes on methods of support for cables, conductors and wiring systems 100 5 Cable capacities of conduit and trunking 109 6 Current-carrying capacities and voltage drop for copper conductors 115 7 Certification and reporting 127 8 — Standard circuit arrangement for household and similar installations 150 9 Resistance of copper and aluminium conductors 157 10 Protective conductor sizing 161 11 Identification of conductors 164 83APPENDIX 1 MAXIMUM DEMAND AND DIVERSITY Appx 1 This Appendix gives some information on the determination of the maximum demand for an installation and includes the current demand to be assumed for commonly used equipment. It also includes some notes on the application of allowances for diversity. The information and values given in this Appendix are intended only for guidance because it is impossible to specify the appropriate allowances for diversity for every type of installation and such allowances call for special knowledge and experience. The figures given in Table 1B, therefore, may be increased or decreased as decided by the engineer responsible for the design of the installation concerned. For blocks of residential dwellings, large hotels, industrial and large commercial premises, the allowances are to be assessed by a competent person. The current demand of a final circuit is determined by summating the current demands of all points of utilisation and equipment in the circuit and, where appropriate, making an allowance for diversity. Typical current demands to be used for this summation are given in Table 1A. The current demand of a circuit supplying a number of final circuits may be assessed by using the allowances for diversity given in Table 1B which are applied to the total current demand of all the equipment supplied by that circuit and not by summating the current demands of the individual final circuits obtained as outlined above. In Table 1B the allowances are expressed either as percentages of the current demand or, where followed by the letters f.l., as percentages of the rated full load current of the current-using equipment. The current demand for any final circuit which is a conventional circuit arrangement complying with Appendix 8 is the rated current of the overcurrent protective device of that circuit. An alternative method of assessing the current demand of a circuit supplying a number of final circuits is to summate the diversified current demands of the individual circuits and then apply a further allowance for diversity. In this method the allowances given in Table 1B are not to be used, the values to 311be chosen being the responsibility of the designer of the installation. The use of other methods of determining maximum demand is not precluded where specified by a suitably qualified electrical engineer. After the design currents for all the circuits have been determined, enabling the conductor sizes to be chosen, it is necessary to check that the limitation on voltage drop is met. TABLE 1A Current demand to be assumed for points of utilisation and current-usit jipment Point of utilisation or current-using | Current demand to be assumed equipment Socket-outlets other than Rated current 2 A socket-outlets and other than 13 A socket-outlets see note 1 2A socket-outlets At least 0.54 Lighting outlet see note 2 Current equivalent to the connected load, with a minimum of 100 W per lampholder Electric clock, shaver supply unit May be neglected (complying with BS 3535), shaver socket-outlet (complying with BS 4573), bell transformer, and current-using equipment of a rating not greater than 5 VA Household cooking appliance The first 10 A of the rated current plus 30 % of the remainder of the rated current plus 5 A if a socket-outlet is incorporated in the control unit British Standard rated current, or normal current All other stationary equipment Note 1; See Appendix 8 for the design of standard circuits using socket- outlets to BS 1363-2 and BS 4343. Note 2: Final circuits for discharge lighting must be arranged so as to be capable of carrying the total steady current, viz. that of the lamp(s) and any associated gear and also their harmonic currents. Where more exact information is not available, the demand in volt-amperes is taken as the rated lamp watts multiplied by not less than 1.8. This multiplier is based upon the assumption that the circuit is corrected toa power factor of not less than 0.85 lagging, and takes into account control gear losses and harmonic current. 85 Appx 1Appx 1 TABLE 1B Allowances for diversity Purpose of Type of premises final circuit fed from conductors or Individual household | Small shops, ‘Small hotels, switchgear to installations stores, offices boarding houses, which diversity | including individual | and business guest houses, etc applies dwellings of a block | premises 1. Lighting 66 % of total current} 90 % of total 75 % of total demand current demand | current demand 2. Heating and | 100 % of total 100 % f.l. of 100 % f.l. of power (but see | current demand up _! largest appliance | largest appliance 3 to 8 below) to 10 amperes +50 %| +75 % fil. of +80 % f.l. of of any current remaining second largest demand in excess of | appliances appliance +60 % 10 amperes f. of remaining appliances 3. Cooking 10 amperes +30 % f.l] 100 % f.l. of 100 % f.l. of appliances of connected cooking largest appliance | largest appliance appliances in excess | +80 % fl. of +80 % f.l. of of 10amperes+5 | secondlargest | second largest amperes if appliance +60 % | appliance +60 % socket-outlet f.l of remaining | f.l. of remaining incorporated in appliances appliances control unit 4. Motors not applicable 100 % f.l. of 100 % f.l. of (other than lift largest motor | largest motor motors which +80 % fil. of +50 % fl. of are subject to second largest | remaining motors special motor +60 % f.l. consideration of remaining motors 5, Water-heaters| 100 % f.l. of largest | 100 % f.l. of 100 % f.. of (instantaneous | appliance +100 % f.l.| largest appliance} largest appliance type)* of second largest +100 % f.l. of +100 % f.l. of appliance +25 % f.1. | second largest | second largest ‘of remaining appliance +25 % | appliance +25 % appliances f.1. of remaining | f.l. of remaining appliances appliancesTABLE 1B continued Allowances for diversity Purpose of final circuit fed from conductors or switchgear to which diversity applies Individual household installations including individual dwellings of a block Type of premises Small shops, Small hotels, stores, offices | boarding houses, and business guest houses, etc premises 6. Water-heaters| (thermostatically controlled) no diversity allowablet 7. Floor warming} installations no diversity allowablet 8. Thermal storage space no diversity allowablet heating installations 9. Standard 100 % of current 100 % of current demand of largest arrangement of final circuits in accordance with Appendix 8 demand of largest circuit +40 % of current demand of every other circuit circuit +50 % of current demand of every other circuit 10. Socket-outlets other than those included in 9 above and stationary equipment other than those listed above 100 % of current demand of largest point of utilisation +40 % of current demand of every other point of utilisation 100 % of current} 100 % of current demand of demand of largest point of | largest point of utilisation utilisation +70 % of current] +75 % of current demand of every | demand of every ‘other point of || other point in utilisation main rooms (dining rooms, etd) +40 % of current demand of every other point of Utilisation For the purpose of this Table an instantaneous water-heater is deemed to be a water-heater of any loading which heats water only while the tap is turned on and therefore uses electricity intermittently. + It is important to ensure that the distribution boards and consumer units are of sufficient rating to take the total load connected to them without. the appli ion of any diversity. 87 Appx 1APPENDIX 2 MAXIMUM PERMISSIBLE MEASURED EARTH FAULT LOOP IMPEDANCE 388 Appx 2 The tables in this Appendix provide maximum permissible 713-11 measured earth fault loop impedances (Zs) for compliance with 413-02-05 BS 7671 where the conventional final circuits of Table 7.1 are 413-02-10 used. The values are those that must not be exceeded in the 413-02-11 tests carried out under Para 10.3.6 at an ambient temperature 413-02-14 of 10°C to 20°C. Table 2E provides correction factors for other 543-01-03 ambient temperatures. Where the cables to be used are to Tables 4, 7 or 8 of BS 6004 or Tables 3, 5, 6 or 7 of BS 7211 or are other thermoplastic (pvc) or thermosetting (Isf) cables to these British Standards, and the cable loading is such that the maximum operating temperature is 70 °C, then Tables 2A, 2B and 2C give the maximum earth loop impedances for circuits with: (a) protective conductors of copper and having from 1mm? to 16 mm? cross-sectional area, (b) _ where the overcurrent protective device is a fuse to BS 88 Part 2 or Part 6, BS 1361 or BS 3036. For each type of fuse, two tables are given: - where the circuit concerned feeds socket-outlets and the disconnection time for compliance with Regulation 413-02-09 is 0.4s, and 13-02-09 - where the circuit concerned feeds fixed equipment only and the disconnection time for compliance with Regulation 413-02-13 is 5s. 413-02-13 In each table the earth fault loop impedances given correspond to the appropriate disconnection time from a comparison of the time/current characteristic of the device concerned and the equation given in Regulation 543-01-03. 543-01-03 The tabulated values apply only when the nominal voltage to Earth (Up) is 230 V. Table 2D gives the maximum measured Zs for circuits protected by circuit-breakers to BS 3871-1 and BS EN 60898, and RCBOs to BS EN 61009.Note: The impedances tabulated in this Appendix are lower than those in Table 41B1, Table 41B2 and Table 41D of BS 7671 as these are measured values at an assumed conductor temperature of 10 °C, whilst those in BS 7671 are design figures at the conductor normal operating temperature. TABLE 2A Semi enclosed fuses Maximum measured earth fault loop impedance (in ohms) when overcurrent protective device is a semi-enclosed fuse to BS 3036 (see Note) () 0.4 second disconnection 413-02-05 Table 4181 Protective Fuse rating (amperes) Peete conductor (mm?) 5 15 20 30 45 1.0 8.00 15 8.00 2.5 to 16.0 1.48 NP NP 1.48 0.91 NP 1.48 5 seconds disconnection rere Table 41D Protective Fuse rating (amperes) 5343-01-03 conductor (mm?) 5 15 20 30 45 1.0 14.80 4.46 NP 15 14.80 4.46 NP 25 14.80 4.46 1.20 4.0 to 16.0 Note: A value of k of 115 from Table 54C of BS 7671 is used. This is suitable for Table 54C insulated and sheathed cables to Tables 4, 7 or 8 of BS 6004 and for i insulated and sheathed cables to Tables 3, 5, 6 or 7 of BS 7211. The k value is based on both the thermoplastic (pvc) and thermosetting (Isf) cables operating at a maximum temperature of 70 °C. NP protective conductor, fuse combination NOT PERMITTED. 89 Appx2TABLE 2B BS 88 fuses Maximum measured earth fault loop impedance (in ohms) when ‘avercurrent protective device is a fuse to BS 88 wa 0.4 second disconnection (see Note) 413-02-05 Table 4181 Protective Fuse rating (amperes) ees conductor (mm?) 6 50 1.0 7 NP 15 7 NP 25 to 16.0 5 seconds disconnection 413-02-05 Table 41D Protective Fuse rating (amperes) 9543-01-03 conductor (mm?) 6 | 10 | 16 | 20 | 25 | 32 | 40 | so 1.0 +4.28| 6.19] 3.20] 1.75] 1.24) 0.69] NP] NP 15 11.28| 6.19) 3.49) 2.43| 1.60] 1.12] 0.67] NP 25 11.28] 6.19] 3.49] 2.43] 1.92) 152| 1.13] 0.56 40 11.28] 6.19] 3.49] 2.43] 1.92] 1:52] 1.13) 081 6.0t016.0 | 11.28] 6.19] 3.49] 243] 1.92] 1.52) 1.13] 087 Note: A value of k of 115 from Table 54C of BS 7671 is used. This is suitable for Table 54C pvc insulated and sheathed cables to Tables 4, 7 or 8 of BS 6004 and for \sf insulated and sheathed cables to Tables 3, 5, 6 or 7 of BS 7211. The k value is based on both the thermoplastic (pvc) and thermosetting (Isf) cables operating at a maximum temperature of 70 °C. NP protective conductor, fuse combination NOT PERMITTED. Appx 2TABLE 2C Maximum measured earth fault loop impedance (in ohms) when overcurrent protective device is a fuse to BS 1361 () 04 second disconnection one Protective Fuse rating (amperes) conductor (mm?) 5 15 20 30 45 10 8.72 0.80 NP 15 8.72 0.96 . 2.5 to 16.0 (ii) 5 seconds disconnection Protective Fuse rating (amperes) conductor (mm?) 5 15 20 30 45 1.0 13.68 4.18 1.75 0.80 NP. 15 13.68 4.18 2.24 1.20 0.34 25 13.68 4.18 2.34 1.54 0.53 4.0 13.68 4.18 2.34 1.54 0.70 6.0 to 16.0 13.68 4.18 2.34 1.54 0.80 413-02-05 Table 41B1 5543-01-03 Table 41D Note: A value of k of 115 from Table 54C of BS 7671 is used. This is suitable for Table 54c pvc insulated and sheathed cables to Tables 4, 7 or 8 of BS 6004 and for Isf insulated and sheathed cables to Tables 3, 5, 6 or 7 of BS 7211, The k value is based on both the thermoplastic (pve) and thermosetting (Isf) cables operating at a maximum temperature of 70 °C. NP protective conductor, fuse combination NOT PERMITTED. 91 Appx 2zwxddy 8 TABLE 2D Table 41B2 Maximum measured earth fault loop impedance (in ohms) when overcurrent protective device is a circuit-breaker to 413-02-05 BS 3871-1 or BS EN 60898 or a RCBO to BS EN 61009 (i) both 0.4 and 5 seconds disconnection times Circuit- Circuit-breaker (amperes) breaker type 5 6 10 15 16 20 25 30 50 63 1 9.60 2.40 096 | 0.76 2 5.49 0.55 0.43 B _ 0.77 | 0.61 3aC 3.84 0.96 0.38 | 0.30 D 0.48 Note: A value of k of 115 from Table 54C of BS 7671 is used. This is suitable for pvc insulated and sheathed cables to Tables 4, 7 or 8 of BS 6004 and for \sf insulated and sheathed cables to Tables 3, 5, 6 or 7 of BS 7211. The k value is based on both the thermoplastic (pvc) and thermosetting (Isf) cables operating at a maximum temperature of 70 °C.TABLE 2E Ambient temperature correction factors Ambient Correction factors (from temperature °C 10 °C) notes 1,2 Notes: 1 - The correction factor is given by: {1 + 0.004 (Ambient temp - 10} where 0.004 is the simplified resistance coefficient per °C at 20 °C given by BS 6360 for both copper and aluminium conductors 2 - The factors are different to those of Table 9B because Table 2E corrects from 10 °C and Table 9B from 20 °C. The values in Tables 2A to 2D are for a 10°C ambient. The ambient correction factor of Table 2E is applied to the earth fault loop impedances of Tables 2A to 2D if the ambient temperature is not within the range 10 °C, to 20 °C. For example, if the ambient temperature is 25 °C the measured earth fault loop impedance of a circuit protected by a 32 A type 1 mcb should not exceed 1.50 x 1,06 = 1.59 Q. 93 Appx2APPENDIX 3 NOTES ON THE SELECTION OF TYPES OF CABLE AND FLEXIBLE CORD FOR PARTICULAR USES AND EXTERNAL INFLUENCES For compliance with the requirements of Chapter 52 for the ch52 selection and erection of wiring systems in relation to risks of mechanical damage and corrosion, this Appendix lists in two tables types of cable and flexible cord suitable for the uses intended. These tables are not intended to be exhaustive and other limitations may be imposed by the relevant Regulation of BS 7671, in particular those concerning maximum permissible operating temperatures. Information is also included in this Appendix on protection against corrosion of exposed metalwork of wiring systems. TABLE 3A Applications of cables for fixed wiring Type of cable Uses Comments Thermoplastic (pvc) | In conduits, cable ducting or| (i) intermediate support may be ‘or thermosetting | trunking required on long vertical runs ee eae (i) 70°C maximum conductor non-sheathed temperature for normal wiring grades — including thermosetting types (4) Gii)cables run in pvc conduit shall not operate with a conductor temperature greater than 70 °C (4) Flat thermoplastic | (i) general indoor use in dry] (i) additional protection may be (pvo) or or damp locations. May necessary where exposed to thermosetting, be embedded in plaster | _ mechanical stresses insulated and (ii) on exterior surface walls,| (ji) protection from direct sunlight may sheathed boundary walls and the be necessary. Black sheath colour is like better for cables in sunlight (iii)overhead wiring {iii)see Note (4) between buildings (6) | (iv)unsuitable for embedding directly (v)underground in conduits) in concrete or pipes (v) may need to be hard drawn (HD) (W) in building voids or ducts) copper conductors for overhead formed in situ wiring (Note 6) 94 Appx 3