Featuring built-in frequency jitter necessary for EMI, while also conserving power during standby!
High-Performance IPD with Frequency Jitter
for Small Charger/Adapter: MIP2Kx Series
Overview
MIP2Kx series is a high-performance IPD designed for 15W battery Unit : mm
chargers and featuring built-in frequency jitter function at PWM
control. It features built-in protection circuits necessary for compact
power source charger circuitry. This allows a significant reduction in Pin No. Pin Name
externally connected parts. It provides PWM control when a normal 1
2
VDD
FB
load is applied and intermittent control with low load. This results in 3 CL
greater efficiency for very low to maximum loads, while also 4
5
VCC
Drain
conserving power during standby. 6 ⎯
7 Source
8 Source
Feature
• Built-in jitter function
• Built-in charge protection circuit
Built-in overcurrent, overheating, load shorting and overvoltage
protection circuits
Applications
Chargers (for DSC, etc.), AC adapter
DIP7-A1
Lineup
Characteristic
Type No. Output *1 Package
VDSS ILIMIT R(DS)ON fosc ⊿f fM
MIP2K2 Up to 5W 0.35A 16.5Ω
MIP2K3 Up to 8W 0.50A 10Ω
700V 100kHz 5.5kHz 260Hz DIP7-A1
MIP2K4 Up to 10W 0.70A 7Ω
MIP2K5 *2 Up to 15W 1.0A 5Ω
*1 The electric power mentioned above depends on the transformer specification and ambient conditions. The information should be used only as a guide.
When using it within a case, output electric power may be decided by heat of IPD.
*2 All characteristic values are only for reference (still under development).
Comparison data of conduction noise
MIP2F4（without jitter function） MIP2K4（with jitter function）
× Average
Peak
Decentralized pulse by jitter function → Lower the avarage
New publication, effective from 31 Oct. 2008
M00852BE
www.DataSheet.in
Frequency jitter function
By frequency jitter function, frequency jitter variation(Δf) changes periodically, by frequency of frequency jitter
modulation factor (fM) as shown below.
fosc=100kHz typ, Δf=5.5kHz typ, fM=260Hz typ
Frequency: High Frequency: Low
Drain current
105.5kHz
Δf=5.5kHz fosc=100kHz (average value of frequency)
Frequency
Time
94.5kHz
1/fM=1/260Hz
*All values are typical
Adapter circuit sample (MIP2K4)
Electric characteristics (MIP2K4：Worldwide input, 8.3V/1.5A output)
VI characteristics of adapter circuit Power efficiency
Vo vs Io η vs Po
9 100
8
7 80
6
60
η [％]
Vo [V]
5
4
40
3 100V
240V
2 100V 20
1 240V
0 0
0 1 2 3 0 2 4 6 8 10 12
Io [A] Po [W]
Precautions on the Sales of IPDs
1) The sale and/or the export of IPD products to any customer or customers located in any country other than Japan is expressly prohibited by the
Agreement made and executed by and between Power Integrations, Inc. and Panasonic Corporation.
2) IPD products purchased from Panasonic Corporation, or its authorized agents, hereinafter referred to as our company, shall be used only for
production purposes by those parties who have duly purchased IPD products. Those who have purchased IPD products shall not use such IPD
products in unmodified form for re-sale, loan, or sample shipment for evaluation purposes to any other parties.
3) If a party who has duly purchased IPD products subcontracts its production to any other parties, including its subsidiaries or any other third parties
inside and/or out of Japan, and the IPD products are consigned to such subcontracting parties thereat, such party is obligated to monitor and control
the quantity of IPD products to prevent any of the aforementioned re-sale, loan or sample shipments from taking place.
4) In the event that any actual or threatened breach or violation of any of the above mentioned 1, 2, or 3, has occurred or is about to occur, Panasonic
Corporation will hold all shipments of IPD products and may request the party alleged to be responsible for such occurrence for necessary.
Parts No. Able to supply Disable to supply Application
• Domestic Japanese • European and American
companies companies
MIP2K□□ For power supply
• Japanese companies in • Local Asian companies
Asia (50% or more owned) • Other local companies
www.DataSheet.in
