MT-600/8000 series

MT-607i
MT-8070iH / MT-6070iH
Installation Instruction

1.0 Installation and Startup Guide

0

Install Environment
7

Where The MT-600/8000 Series is designed for industrial. The temperature range of operating
Used is from 32 to 113 °F (0 to 45 °C), as majority of industrial environments. It may not be
suitable for using in certain outdoor applications. Please consult the factory for
advised usage in outdoor applications.
NEMA The MT-600/8000 Series front bezel is NEMA 4 rated. When installed properly in a
Rating
NEMA 4 panel, the NEMA 4 rating of the panel will not be compromised. This means
that fluids will not enter the panel during wash downs.
Electrical The MT-600/8000 Series has been tested to conform to European CE requirements.
Environment
This means that the circuitry is designed to resist the effects of electrical noise. This
does not guarantee noise immunity in severe cases. Proper wire routing and
grounding will insure proper operation.
Mechanical Avoid installing units in environments where severe mechanical vibration or shocks
Environment
are present.

2.0 Installation Instructions

1

2.1 Mounting Instructions

4

2.1.1 Location Considerations

8

Care should be taken when locating equipment behind the unit to ensure that AC power wiring, PLC
output modules, contactors, starters and relays, and any other source of electrical interference are located
away from the back of the unit.

Particular note should be taken to the position of variable speed drives and switching power supplies.
Their input and load cables should be screened to a central star earth point.

1
2.1.2 Making a NEMA-4 Mounting
9

Panel The unit can be mounted into panels with a depth of 4”(105mm). It is recommended that
Details the unit be mounted on the front panel of a steel enclosure, through an appropriate opening.
Allow a clearance of 1”(25mm) around the sides of the unit for mounting hardware. Allow
clearance for cable connections to the back of the unit. Unit depth may vary according to
cable type used. Typically, plan a depth to accommodate at least 4”(105mm) behind the
panel.
NEMA-4 Put the unit through the panel cut out. Slide the clamps (packed with product) into the 4
Mounting holes provided around the case. Tighten the clamping screws in an even pattern until the
unit is secured in the panel. Screw Torque: 2.6~3.5 lbf.in. (For reaching waterproof effect
and to prevent the panel from being deformed.)
VESA There are 4 holes on back panel for locking VESA, The screw: M4 P0.7mm, length:
Mounting
shorter then 8.0mm, and screw torque: 2.6 lbf.in.
Caution! Do not over tighten mounting clamps!
Note: Specifications
57

Note: To seal to NEMA-4 specifications, all supplied mounting clamps must be used and
panel cannot flex more than 0.010”.
2.1.3 Environmental Considerations
10

z The MT-600/8000 are to be used indoors as built in displays. Make sure that the displays
are installed correctly and that the operating limits are followed (See Specifications).
z Do not operate the unit in areas subject to explosion hazards due to flammable gases,
vapors or dusts.
z The unit should not be installed where fast temperature variations and/or high humidity
are present. This will cause condensation of water in the device.
z Do not install these terminals in environments where have inflammable gases.

2.2 Power Connections

5

Make sure that all local and national electrical standards are met when the installing the unit.
Contact your local authorities to determine which codes apply.
2.2.1 Power Requirements
11

Power The MT-600/8000 can be powered by DC power only. The specified

voltage range is 24±20% Volts DC. This insures compatibility with most
controller DC systems.
The power conditioning circuitry inside the unit is accomplished by a
switching power supply. The peak starting current can be as high as
700mA.
Fusing If the display does not come on within 5 seconds of power up, remove
Requirements power. An internal fuse will prevent damage if the polarity of the DC
power is incorrect. Check wiring to insure proper connections and try to
power up again.
Caution
51

An Internal fuse will prevent damage for over voltage condition however
High Voltage
50

it isn’t guaranteed.
DC voltage sources should provide proper isolation from main AC power
and similar hazards.

2
 Caution A Hard-wired EMERGENCY STOP should be fitted in any system using
Emergency an MT-600/8000 to comply with ICS Safety Recommendations.
Stop
Caution
52 Do not power the MT-600/8000 and inductive DC loads, or input
Supply Voltage circuitry to the controller, with the same power supply. Note: The 24 VDC
Condition
53 output from some controllers may not have enough current to power the
MT-600/8000.
Caution Wire lengths should be minimized (Maximum 1600’ (500 m) shielded,
Wire Routing
54 1000’ (300 m) unshielded).
Wires should be run in pairs with a neutral or common paired with a hot or
signal line.
If wiring is to be exposed to lightning or surges, use appropriate surge
suppression devices.
Keep AC, high energy, and rapidly switching DC wiring separate from
signal wires.
Equip ungrounded DC supplies with a resistor and capacitor in parallel to
earth ground. This provides a path for static and high frequency
dissipation. Typical values to use are 1MOhm and 4700pF.
To prevent the HMI from becoming damaged or having sound output
Caution issues, after turning the device off, please wait 10 seconds before turning
the device on again.

Connection
55 To make a connection, strip about 3/8” of insulation off the end of the
wire, turn the connector screw counterclockwise until the gap is wide
open, insert the wire all the way in, and turn the screw clockwise until it’s
tight.
Connect positive DC line to the ‘+24V’ terminal and the DC ground to the
‘0V‘ terminal.
2.2.2 Grounding Requirements
12

Chassis ground must be used. DC ground is not directly coupled to Earth

ground internally. It is preferable not to ground DC negative return to chassis
ground as poor site earths can introduce noise into a system, but if necessary
an earth connection should be made, from the power supply return point to
the central star earth point. Ground conductors should be as short and as large
in size as possible. The conductors must always be large enough to carry the
maximum short circuit current of the path being considered. Ground
conductors should be connected to a tree from a central star earth ground
point. This ensures that no ground conductor carries current from any other
branch.
2.2.3 CE Requirements
13

To make an MT-600/8000 comply with EMC directives, and to reduce susceptibility to electrical
interference, a separate #14 AWG ground wire should be taken to the chassis ground terminal of the
power connector. This ground connection should be run directly to the central star earth connection
point (as recommended in most Installation Instructions).
2.2.4 Safety Guidelines
14

This section presents recommended installation practices, and procedures. Since no two
applications are identical, these recommendations should be considered as guidelines.

Hardware WARNING!
Considerations
58

The system designer should be aware that devices in Controller systems could
fail and thereby create an unsafe condition. Furthermore, electrical
interference in an operator interface, such as an MT-600/8000, can lead to
equipment start-up, which could result in property damage and/or physical
injury to the equipment operator.
If you, or your company, use any programmable control systems that require
an operator or attendant, you should be aware that this potential safety hazard
3
 exists and take appropriate precautions. Although the specific design steps
depend on your particular application, the following precautions generally
apply to installation of solid-state programmable control devices. In addition,
these precautions conform to the guidelines for installation of Controllers as
recommended in the NEMA ICS 3-304 Control Standards.
Programming To conform with ICS Safety Recommendations, checks should be placed
Considerations in the controller to ensure that all writable registers that control critical
parts of plant or machinery have limit checks built into the program, with
an out-of-limit safe shut down procedure to ensure safety of personnel.

ICS 3-304.81 Safety Recommendations:

Consideration should be given to the use of an emergency stop function, which is independent of the programmable
controller.
Where the operator is exposed to the machinery, such as in loading or unloading a machine tool, or where the machine
cycles automatically, consideration should be given to the use of an electromechanical override or other redundant means,
independent of the programmable controller, for starting and interrupting the cycle.
If provision is required for changing programs while the equipment is in operation, consideration should be given to the
use of locks or other means of assuring that only authorized personnel can make such changes.
These recommendations are intended as safeguards against the failure of critical components and the effects of such
failures or the inadvertent errors that might be introduced if programs are changed while the equipment is in operation. *

z The ICS 3-304.81 Safety Recommendations are reproduced by permission of the National Electrical
Manufacturers Association from NEMA ICS 3-304

2.3 Communications Connections

6

The ports as you look at the back of the case, are the ports for connecting to a PLC or some external
device (Controller Connectors).
2.3.1 Connector COM1 [RS232], COM2 [RS232]
15

Cable Different cables are required for various devices.

Requirements
Restrict cable length to less than 500’ (150m) for RS485/422 devices and
Caution 50’ (15m) for RS232 devices to avoid communications problems.
The COM light on the front of the MT-600/8000 will turn on with each
Ethernet communication.
Shielded cable must be used for long lengths or cables run in an electrically
noisy environment.
Do not run cables next to AC power lines or near sources of electrical noise.
Be sure that the cable ends have been inserted all of the way into mating
connectors and are secure
Pin Designations Pin assignment of the 9 Pin, Male, SUB-D, COM1 [RS-232] and COM2
[RS-232] Port.

Pin# Symbol COM1 [RS232] COM2 [RS232]

1 Not used
COM1 [RS-232] 2 RxD Received Data
COM2 [RS-232]
3 TxD Transmitted Data
4 TxD Transmitted Data
5 GND Signal Ground
6 RxD Received Data
7 RTS Ready to send output
8 CTS Clear to send input
9 Not used

4
 2.3.2 Connector COM1[RS485] , COM3[RS485] and COM3[RS232]
16

The 9 Pin, Female, SUB-D, COM1 [RS-485] , COM3 [RS-485] and COM3 [RS-232] Port on the back
of the unit is the RS-232 and RS485/422 communications port for connecting to a controller.

COM1 [RS485]2w supports MPI 187.5K.

Connection
Pin Designations Pin assignment of the 9 Pin, Female, SUB-D COM1 [RS-485], COM3
[RS-485] and COM3 [RS-232] Port
Pin# Symbol Com1 Com1 Com3 Com3
[RS485]2w [RS485]4w [RS485] [RS232]
COM1 [RS-485] 1 Rx- Data- Rx-
COM3 [RS-485] 2 Rx+ Data+ Rx+
COM3 [RS-232] 3 Tx- Tx-
4 Tx+ Tx+
5 GND Signal Ground
6 Data- Data-
7 TxD Transmit
8 RxD Receive
9 Data+ Data+
2.3.3 USB Host port
17

USB 1.1 Host interface supports USB mouse, keyboard, USB Flash Drive and printer.
While using external hard drive, please use external power supply. Do not use USB port to charge external
device.
2.3.4 USB client port
18

It can use Mini USB cable (RZCMT6100) to download projects from PC by the USB 2.0 client port. Support
USB 2.0 client interface. The cable regulation must accord with HI-SPEED USB Revision 2.0 SHIELDED.
How to install USB driver of HMI i series
It is necessary to install USB driver of HMI on PC before at the first time enjoying this function. (The HMI
models: MT6050i, MT6056i, MT6070iH, MT6100i, MT8070iH and MT8100i)
1. Using USB cable mini side plug to HMI and another side plug into PC. The PC will display “Found New
Hardware Wizard” dialog. Select “Install from a list or specific location (Advanced)”.
2. Check “Include this location in the search”, and assign the path to install Weintek HMI i Series driver
from C:\EB8000\usbdriver.
3. If the USB driver successfully be installed, user can check it at Computer Management / Device Manager
to check. Then user can download project to HMI i series through USB cable.

5
2.3.5 Connecter Wire
19

MT8-Ethernet/RZC045120: Direct connect (Ethernet crossover cable)

MT-600/8000 PC or Note
Ethernet RJ45 Wire color Book RJ45
1 TX+ White/Orange 3 RX+
2 TX- Orange 6 RX-
3 RX+ White/Green 1 TX+
6 RX- Green 2 TX-
MT8-COM1/RZC002320 MT8-COM3/RZC004850

5 9
5 9
1 6

1 6

5
9

6 6 1 5 9
1
9 5 1 6

5 9

6 5 9
1

1 6

2.3.6 Dip Switch

20

SW1
21 SW2
22 SW3
23 SW4 Mode
24 25

ON
26 OFF
27 OFF
28 OFF Touch Screen Calibrate mode
29 30

OFF
31 ON
32 OFF
33 OFF Hide MT8000 System Setting Bar
34

OFF
35 OFF
36 ON
37 OFF Boot Loader mode
38 39

OFF
40 OFF
41 OFF
42 ON Reserve
43 44

OFF
45 OFF
46 OFF
47 OFF Normal
48 49

z Touch Screen Calibrate and Reset Password mode: In this

mode when you power on the MT8000 series, the screen
will display a “+” sign upper-left of the screen. Use a
stylus or finger to push the center of the “+” until it moves.
The “+” moves to upper-left, upper-right, lower -left,
lower-right and center. When all five “+” are done the “+”
will disappear. The Touch Screen parameter will be stored
in Flash Rom.

z If losing or forgetting system passwords, users can set Dip

Switch 1 to “ON” position, the rest of Dips remain on
“OFF” position and then reboot MT8000 series. Under
this situation, MT8000 series will jump to Touch Adjust
(Touch screen calibration) mode. After calibration, the
pop-up window appears as the illustration below. Users
will be inquired if restoring the system password to the
default value.
z When “YES” is chosen, another pop-up dialog appears as
below. Users will be confirmed again if restoring the
system password to the default value and will be asked to
input “YES”. Then click OK. (The default password is
111111. However, other passwords, including download,
upload password and History backup password, have to be
reset.)

Note: When the reset action is be taken, projects and saved data in
the HMI will all be cleared.

6
2.4 CE Requirements
EU directives that apply to the MT-600/8000 Series:
56

z EMC Directive (2004/108/EC) electromagnetic emissions and immunity.

z UL508（ISBN 0-7629-0404-6）machine safety for use in Pollution Degree 2 Environment.
z MT-600/8000 products will be CE-marked to indicate compliance with the EMC Directive.
The MT-600/8000 Series has been designed to operate satisfactorily in electromagnetic noise (immunity) and
without emitting high levels of electrical noise into the environment (emission). The units are designed to
meet European Community standards when installed per the wiring instructions in this manual.
Compatibility The MT-600/8000 has been designed to meet electromagnetic compatibility for industrial
Standards environments.
z EN 55022: 2006 Class A
z EN 61000-3-2: 2006
z EN 61000-3-3: 1995+A1: 2001+A2: 2005
z EN 55024: 1998+A1: 2001+A2: 2003

3.0 Specifications
2

MT6070iH MT8070iH MT607i

Hardware Specification
Display 7" TFT LCD
Brightness 375 cd/m2
Color 65,536 colors
Contrast Ratio 500:1
Resolution (WxH dots) 800 x 480
Back light LED
Backlight life time (avg.) 30,000 hr. min.
Touch panel 4 wires resistive type
Touch Accuracy Active Area Length(X)±2%, Width(Y)±2%
I/O port COM1 (RS-232/RS-485 2W/4W), COM2(RS232), COM3(RS-232/RS-485 2W)
Ethernet port N/A 1 Ethernet port (10/100 Base-T)
USB USB Host port x 1, USB Client port x 1
Processor 32bit RISC CPU 400MHz
Flash memory 128MB
DRAM 64MB DDR2 RAM on board
SD card slot N/A Support SD/SDHC
Audio N/A YES
RTC Built-in (CR2032 3V lithium battery.)
General Specification
Input Power 24±20% VDC Power Isolator Inside
Max Power Consumption 250 mA@24VDC
Protection structure IP65 front panel (O ring seal)
Storage Temperature -20~60°C (-4° ~ 140°F)
Operating Temperature 0~45°C (32° ~ 113°F)
Operation humidity 10-90% RH (non –condense)
Enclosure Plastic
Dimensions WxHxD 200 x 146 x 42.5mm
Panel cutout dimension 192 x 138 mm (7.5"x5.4")
Weight Approx. 0.85 kg (1.87 lbs)
Operating System
Operating System EB8000 2.0.0 or Newer Windows CE.net 5.0

7
3.1 Limited Liability Warranty
Weintek products include the isolated power supply are covered by a limited liability warranty from
defects in material and workmanship. This warranty does not apply:
(a) if, in the judgment of Weintek, the product fails due to damage from shipment, handling, storage, accident
(natural and man-mad) ;
(b) If the product fails due to misuse, including but not limit to incorrect set-up and wiring, current leakage
from machine platform and incorrect input power;
(c) If the product has been maintained in a manner not conforming to product's instructions or has been
modified in any way,
(d) If the serial number has been defaced or removed.

4.0 Dimensions of MT-607i / MT-6070iH /

3

MT-8070iH

Bottom View

Front View

Cutout dimensions:
MT607i / MT6070iH / MT8070iH:
192mm [7.559"] W x 138mm [5.433"] H

Rear View
a DIP SW & Reset button g Com1 RS485, Com3 RS485, Com3 RS232
b Fuse h Com1 RS232, Com2 RS232
c Power connector i Ethernet port (RJ-45) (MT6070iH N/A)
d VESA 75mm screw holes j USB Host port
e Audio (MT6070iH N/A) k USB Client port
f SD card slot (MT6070iH N/A)
GME8607i0_MT6070_8070iH_MT607i_Installation_101028
8