Pedestal Bearings Type WP

Diameter Range 140...900 mm

Pedestal bearings type WP are

general purpose bearing systems
with housings according to DIN
31690.
They are mostly used in horizontal
electrical machines such as
generators and motors.
Pedestal Bearings Type WP
Diameter Range 140…900 mm

Applications Oil Supply

Pedestal bearings type WP are used, due to their Depending upon the application, different modes of
versatility, in a wide variety of applications, such as: lubrication are available. Under most conditions,
lubrication is achieved via an external oil circulation
 Turbo generators system. A loose oil ring may achieve lubrication in
 Hydro generators emergency run-down condition. For slow-running
 Water turbines and pumps applications, lubrication may be achieved by a loose oil
ring alone. Fixed oil rings for high oil throughput in
 Blowers
slow-speed applications are available on request.
 Motors and generators Bearings supplied through a single oil pocket due to
Materials changing load angles are available.
Housings are made of cast iron EN-GJS-300. For high Heat Dissipation
thrust loads, EN-GJS-400-15 is available. Bearing In case of an external oil circulation system, the friction
shells are made of high quality steel lined with a layer heat is dissipated by convection via the same. For
of babbitt. slow-running low-load applications, dissipation via the
Seals housing surface may be sufficient. Internal water
Different types of seals are available, ranging from coolers to increase heat dissipation are available.
protection class IP44 up to IP55 to suit your Temperature Control
application. Seals are available as floating labyrinth Provisions for temperature measurements in shell and
seals for sizes 18 through 28 and as fixed labyrinth oil sump are available on both sides of the bearing. In
seals for sizes 22 through 71. Special seals are case of tilting pad thrust bearings, provision for axial
available. bearing temperature measurement is also available on
Electric Insulation both sides. Additional measurement provisions are
Pedestal bearings type WP are available with electrical available on request. Temperature readings may help
insulation between shell and housing up to size 56. in determining bearing failure when evaluating
Insulation is ensured by a high-quality spray-cast layer transient temperature changes.
of ECTFE with excellent long-term stability in the Bearing Selection
spherical seat of the housing. Calculation software based on E DIN 31652,
Special Designs DIN 31653 and DIN 31654 for bearing pre-selection is
Modifications to the bearings of the WP series are available on request. Specified load cases will be
available to optimally suit your machine design and calculated by GTW with specialized calculation
application. The majority of WP bearings is specially software able to model bearing behaviour more
adapted to the customers’ specifications. precisely.

2
Designation of Bearing Types

1.) Manufacturer
W Gleitlagertechnik Weißbacher GmbH
2.) Type
P Pedestal housing according to DIN 31690

3.) Heat dissipation

N Convection via the housing surface
W Convection via the housing surface and water cooling in oil sump
Z External oil circulation system with oil cooling
X External oil circulation system with oil cooling and large oil throughput

4.) Shape of bore and ring lubrication

C Cylindrical bore without oil ring
L Cylindrical bore with loose oil ring
F Cylindrical bore with fixed oil ring
Y Two lobe bore without oil ring
V Four lobe bore without oil ring

5.) Thrust part

Q Without thrust part
B Babbitt-lined plain shoulders with oil grooves for small dynamic thrust loads
K Taper land faces for both directions of rotation
D Taper land faces for a single direction of rotation
A Circular tilting pad thrust pads type WD

6.) Housing size

7.) Nominal bearing diameter

Example Pedestal bearing, housing size 22, shaft diameter 250 mm with external oil circulation
system and oil cooling, two-lobe bore and taper land faces for both directions of rotation.

Slide bearing WPZYK 22-250

3
Dimensions of Bearings Type WP
Sizes 18 to 35

Size D H7 B b1 b2 b4 b14 d1/d2 d3 d8 d9 d10 d11 d18 d19 d20 d21 d22 d23 d24 d25

140 140 152 195

160 160 40 172 215
8x
18 180 135 160 299 245 255 180 275 for G½ G2 15 192 240 320 340 G½ G½ 13
M8
200 200 M30 212 250
225 225 237 275
180 180 194 245
200 200 46 214 265
8x
22 225 170 200 364 310 320 225 340 for G¾ G2½ 15 239 290 380 400 G½ G½ 13
M8
250 250 M36 264 315
280 280 294 345
225 225 241 300
250 250 266 325
280 280 55 296 355
8x
28 300 215 250 488 370 380 300 440 for G¾ G2½ 20 316 375 500 525 G½ G¾ 13
M8
315 315 M42 331 390
335 335 351 410
355 355 371 430
280 280 300 365
300 300 320 385
315 315 335 400
335 335 55 355 425
12x
35 355 260 300 562 440 460 355 520 for G1 G3 20 375 450 600 640 G½ G1 18
M10
375 375 M42 395 470
400 400 420 495
425 425 445 520
450 450 470 520

4
 d27 d28 e1 e2 e3 e4 e5 e6 e7 e8 h1 h2 h3 h4 m n n1 l1 l2 t z m [kg] V [l]

31.5/40/50 190/200/210 16/14/12

31.5/40 210/220 211 18/14
31.5 230 70 68 105 30 155 30 215 0 315 550 70 29 560 150 - 660 470 20 240 10
- - -
190
- - -
40/50/63 245/255/270 16/14/12
40/50 265/275 261 18/16
40/50 285/295 80 83 135 40 175 40 245 0 375 665 80 37 670 200 - 800 570 20/16 470 20
- - -
248
- - -
50/63/80 295/315/335 16/14/12
50/63/80 325/345/355 315 18/16/12
50/63 355/375 20/16
50 380 95 106 155 50 220 50 310 0 450 805 90 42 800 250 - 950 680 265 22 780 33
50 390 256 22
- - 236 -
- - 223 -
63/80/100 370/390/410 150 16/14/12
63/80/100 390/405/425 160 16/14/12
63/80 405/425 170 18/14
63/80 425/440 180 18/16
63 445 120 100 190 65 320 75 385 65 530 940 95 50 950 300 - 1100 800 335 20 1350 30
63 460 200 20
- - 210 -
- - 220 -
- - 230 -

All dimensions in mm We reserve the right to introduce modifications

5
Dimensions of Bearings Type WP
Sizes 45 to 71

Size D H7 B b1 b2 b4 b14 d1/d2 d3 d8 d9 d10 d11 d18 d19 d20 d21 d22 d23 d24 d25 d27

355 355 380 460 80/100/125

375 375 400 480 80/100/125
400 400 425 505 80/100
425 425 62 450 530 80/100
12x
45 450 325 375 652 530 550 450 690 for G1 G3 20 475 555 730 780 G½ G1 18 80
M12
475 475 M48 500 580 80
500 500 525 605 -
530 530 555 635 -
560 560 585 645 -
450 450 480 565 100/125/140
475 475 505 590 100/125/140
500 500 530 615 100/125
530 530 62 560 645 100
12x
56 560 415 475 762 640 660 560 800 for G1½ G4 25 590 675 890 950 G½ G1 18 100
M12
600 600 M48 630 715 -
630 630 660 745 -
670 670 700 785 -
710 710 740 780 -
560 560 595 685 125/140/160
600 600 635 725 125/140/160
630 630 665 755 125/140
670 670 75 705 795 125
16x
71 710 530 600 914 780 810 710 980 for G1½ G4 35 745 835 1100 1150 G½ G1 18 100
M12
750 750 M56 785 875 -
800 800 835 925 -
850 850 885 975 -
900 900 920 990 -

6
 d28 e1 e2 e3 e4 e5 e6 e7 e8 h1 h2 h3 h4 m n n1 l1 l2 t z m [kg] V [l]

465/485/510 190 16/14/12

485/505/530 190 16/14/12
510/530 205 18/14
535/555 215 18/16
560 130 120 230 75 360 90 420 80 600 1115 120 53 1150 355 - 1350 980 400 20 2300 50
585 245 20
- 255 -
- 255 -
- 270 -
585/610/625 225 16/14/12
610/635/650 225 16/14/12
635/660 240 18/14
665 255 18
690 165 160 270 105 415 150 480 0 670 1315 130 58 1400 450 150 1600 1180 455 20 4000 80
- 295 -
- 310 -
- 310 -
- 320 -
725/740/760 250 16/14/14
765/780/800 250 18/16/14
795/810 270 18/16
835 295 18
850 175 210 320 140 500 190 540 0 800 1575 206 110 1800 560 200 1990 1550 560 24 7300 115
- 340 -
- 370 -
- 370 -
- 370 -

All dimensions in mm We reserve the right to introduce modifications

7
Shaft Dimensions
Sizes 18 to 35

b5 d12
Size D (±0.1)
b6 b7 b8 b9 d13(e8)/d14 d15 r
B,K,D A
140 195 224/242/262 160/140 180
160 215 244/262 180/160 200
18 180 160.4 190 180 190 10 240 264 200/180 225 6
200 250 - 225/200 250
225 275 - 225/225 265
180 245 288/308/336 200/180 225
200 265 308/328 225/200 250
22 225 200.4 240 220 240 13.5 290 328/348 250/225 280 10
250 315 - 280/250 300
280 345 - 280/280 315
225 300 348/380/418 250/225 280
250 325 378/411/438 280/250 300
280 355 408/441 300/280 315
28 300 250.4 300 280 300 19 375 433 315/300 335 10
315 390 443 335/315 355
335 410 - 355/335 375
355 430 - 355/355 400
280 365 435/472/512 300/280 315
300 385 455/487/527 315/300 335
315 400 470/507 335/315 355
335 425 490/522 355/335 375
35 355 300.5 360 315 335 10 450 510 375/355 400 12
375 470 525 400/375 425
400 495 - 425/400 450
425 520 - 450/425 475
450 520 - 450/450 500

All dimensions in mm We reserve the right to introduce modifications

8
Shaft Dimensions
Sizes 45 to 71

b5 d12
Size D (±0.1)
b6 b7 b8 b9 d13(e8)/d14 d15 r
B,D,K A
355 460 550/590/640 375/355 400
375 480 570/610/660 400/375 425
400 505 595/635 425/400 450
425 530 620/660 450/425 475
45 450 375.5 445 400 425 13 555 645 475/450 500 16
475 580 670 500/475 530
500 605 - 530/500 560
530 635 - 560/530 600
560 645 - 560/560 630
450 565 690/740/770 475/450 500
475 590 715/765/795 500/475 530
500 615 740/790 530/500 560
530 645 770 560/530 600
56 560 475.5 555 500 530 16 675 795 600/560 630 16
600 715 - 630/600 670
630 745 - 670/630 710
670 785 - 710/670 750
710 780 - 710/710 790
560 685 855/885/925 600/560 630
600 725 895/925/965 630/600 670
630 755 925/955 670/630 710
670 795 965 710/670 750
71 710 600.5 690 630 670 20 835 955 750/710 800 16
750 875 - 800/750 850
800 925 - 850/800 900
850 975 - 900/850 940
900 990 - 900/900 975

All dimensions in mm We reserve the right to introduce modifications

9
10
11
 WP 05.2014

Weseler Straße 32 Tel. +49-2802-1025-0

D-46519 Alpen Fax. +49-2802-7435
www.gtwalpen.de E-Mail: [email protected]

12