INTRODUCTION Baker SPD

FLUID END EXPENDABLE PUMP PARTS

Look anywhere in the oil and gas industry and you’ll find Baker SPD Fluid End Expendable parts and they are
100% guaranteed.

BAKER SPD NOW GIVES MORE DEPTH AND STRENGTH

Since 1923, the finest oil industry fluid end expendable pump parts have always been “American.” American
became Reed American in 1977; the tradition continued. Now the name is Baker SPD, and the quality of the
line runs even deeper than ever. Here’s why:
• Baker SPD has set worldwide product and service standards - higher than ever.
• Baker SPD is upgrading the line’s product research, engineering, quality control, and testing.
• Baker SPD warranties their quality products from manufacturing defects.

YOU’RE THE FINAL INSPECTOR

MUD PUMP FLUID END

Field applications seem to get tougher by the year, but so do Baker SPD products - thanks to our continuous

EXPENDABLE PARTS
testing and product improvement programs. It’s not unusual for us to spend as much as three years performing
hundreds of grueling tests before a new or improved Baker SPD product appears on the market.
Our customers are, in a sense, the final “inspectors” of our products; however, all Baker SPD pump parts are
rigorously inspected - and many also individually tested - before they’re released from the factory. Because the
only thing we want coming back is you.

THE STRENGTH AND KNOWLEDGE TO LEAD AN INDUSTRY

For 70 years, the organization that’s now Baker SPD has been demonstrating its ability to look ahead, commit
resources, and deliver products in the oilfield. Now, as a division of Baker Oil Tools, Baker SPD is widely
regarded as one of the most innovative and responsive service companies around.
Baker SPD Fluid End Expendables have become industry standards due to their superior engineering, quality
control, and testing. They are known for dependability in the field and long service between change-outs.
Baker SPD has the desire, strength, and knowledge to lead the industry through all its changes in the coming
years. The best is yet to come!

61
Baker SPD VALVES AND SEATS

DOUBLE ANGLE O-RING VALVE

The Double Angle O-ring Valve is made with a tough one-piece
body to run more hours between change outs. It's made with
carburized premium alloy steel to resist wear, provide a positive
seal, and help protect against wash out or damage to the pump.
FEATURES
Double Angle O-ring Seat, Spring, and Valve
•Specified for all drilling operations up to and exceeding
5,000 psi
• Maximum operating temperature is 170°F
• Patented polyurethane insert is noted for its “Double Angle” 55°
seal contact surface, which maintains cylinder priming during pump shutdown
• Sizes fit most mud pumps
• Shelf life of polyurethane insert is maximum of 5 years
• Body is a one-piece design, configured to give maximum containment of the insert with minimum use of
material

DOUBLE ANGLE O-RING “BLUE STREAK™” HIGH TEMPERATURE VALVE

The High Temperature Double Angle O-ring Valve body is a
one-piece design, configured to give maximum containment of
the insert with minimum use of material. The valve and insert
configuration has been operated at pressures up to and
exceeding 5,000 psi.
FEATURES
•Maximum operating temperature is 200°F
Double Angle O-ring Seat, Spring,
and High Temperature Valve •Shelf life of polyurethane insert is maximum of 5 years

STANDARD PLATE TYPE VALVE

The Standard Plate Type Valve is extremely durable to its premium forged alloy steel body and its unique design.
It has been proven by more than 50 years of oilfield service. To prevent dry pistons and liners at startup, the
valve features a patented double angle polyurethane insert that maintains cylinder priming during pump shut-
down. The precise control of insert pre-load is accomplished with a flat ground insert retaining plate and split
retainers. The insert can be replaced in the field with minimum down time. This valve is designed to fit pumps in
the oilfield and is used with Baker SPD seats.
FEATURES
•Specified for all drilling operation up to and exceeding
3,500 psi
•Maximum temperature rating for the standard polyurethane
insert is 170°F
•Maximum temperature rating for the Buna-N rubber insert is
225°F
•Available with Buna-N rubber or polyurethane inserts
•Shelf life of polyurethane insert is maximum of 5 years
Standard Plate Type Seat, Spring, and Valve •Shelf life of Buna-N rubber is maximum of 10 years
•Valves with rubber lipless inserts are rated for pressure up to
2,500 psi

Note: Baker SPD Double Angle O-ring and Standard Plate Type Valves do not interchange with any other
manufacturer.

62
VALVES AND SEATS Baker SPD

3-WEB PLATE TYPE/DOUBLE ANGLE

VALVE SEAT
Long service life and high flow areas have made this seat the
most popular in the oilfield for over 50 years. Made of
carburized premium alloy steel, the seat resists wear even in
the roughest conditions. The original 3-web design allows
maximum flow area through the seat while providing maximum
seating area for the valve. Precision ground tapers allow this
seat to fit the deck of most pumps.
3-Web Plate Type/Double Angle Valve Seat
FEATURES
• Seat sealing angle with the valve is 55°
• Full length lower stem guide is fully hardened
• Used with both Double Angle O-ring and Plate Type Valves
Note: Baker SPD 3-web seats are not interchangeable with any other manufactures.

MUD KING® VALVES

MUD PUMP FLUID END

EXPENDABLE PARTS
The Mud King® Valves and Seats are 100% interchangeable
with Mission®. The body is designed with a pre-loaded insert
utilizing a machined “knock-on” nut retainer plate. This design
allows for field replacement of insert with a minimum of down
time. Valves are available with polyurethane or rubber inserts
to match operating pressure, temperature, and mud type.
FEATURES Mud King® Seat, Spring, and Valve
• Rated for all drilling operations up to and exceeding
5,000 psi
• Maximum temperature rating for the standard polyurethane insert is 170°F
• Maximum temperature rating for the Buna-N rubber insert is 225°F
• Valves with rubber lipless inserts are rated for pressures up to 2,500 psi
• Shelf life of polyurethane insert is maximum of 5 years
• Shelf life of Buna-N rubber is maximum of 10 years

MUD KING® “BLUE STREAK™” HIGH TEMPERATURE VALVE

FEATURES
• Maximum operating temperature is 200°F
• Shelf life of polyurethane insert is maximum of 5 years
• Higher temperature resistant

4-WEB MUD KING® SEATS

Are designed to work with the Mud King® Valves only.
FEATURES Mud King “Blue Streak™” 4-Web Seat, Spring,
and High Temperature Valve
• Seat sealing angle with the valve is 55°
• Full length lower stem guide fully hardened

63
Baker SPD VALVES AND SEATS

WM FULL OPEN VALVE AND SEAT

Baker SPD offers the full open valve and seat design as an
alternative to the web style. This style eliminates the need of
removing the discharge seat when replacing the suction seat
in the over and under valve pot arrangement given to certain
triplex pumps.
The wing guided valve and seat are carburized for extended
service life. Design features provide superior flow character-
WM Full Open Seat, Spring, and Valve istics and maximum flow area. Abrasion resistant polyure-
thane inserts are easily replaced in the field.
FEATURES
• Specified for all drilling operations up to and exceeding 5,000 psi
• Body is a two-piece inertia welded design, configured to give maximum containment of insert with minimum
use of material
• Insert is a lipless 45° seal contact surface with a broad contact area to resist abrasion
• Maximum operating temperature is 170°F
• Patented polyurethane insert is noted for its “Double Angle” 45° seal contact surface, which maintains cylin-
der priming during pump shutdown
• Shelf life of polyurethane insert is 5 years
• A 45° angle on the seat allows the valve to fully interchange with the National design valves and seats

WM FULL OPEN “BLUE STREAK™” HIGH TEMPERATURE VALVE

FEATURES
•Maximum operating temperature is 200°F
•Shelf life of polyurethane insert is 5 years
•Higher temperature resistant
•Specified for all drilling operations up to and exceeding
5,000 psi

WM Full Open Seat, Spring, and

“Blue Streak™” High Temperature Valve

64
VALVES AND SEATS Baker SPD

MUD MAX® FULL OPEN VALVE

The Mud Max® Valves and Seats are 100% interchangeable with the Harrisburg Roughneck® style.
FEATURES
• Specified for all drilling operations up to and exceeding
4,000 psi
• Body is a two-piece inertia welded design, configured to
give maximum containment of insert with minimum use
of material
• Insert is a lipless 45° seal contact surface with a broad
contact area to resist abrasion
• Maximum temperature rating for the standard
polyurethane insert is 170°F
Mud Max® Full Open Valve Seat, Spring, and Valve
• Maximum temperature rating for the Buna-N rubber
insert is 225°F
• Shelf life of polyurethane insert is maximum of 5 years
• Shelf life of Buna-N rubber is maximum of 10 years

MUD PUMP FLUID END

EXPENDABLE PARTS
MUD MAX® FULL OPEN “BLUE STREAK™” HIGH TEMPERATURE VALVE
FEATURES
• Specified for all drilling operations up to and exceeding
4,000 psi
• Higher temperature resistant
• Maximum operating temperature is 200°F
• Shelf life of polyurethane insert is 5 years

MUD MAX® FULL OPEN SEATS

Mud Max® Full Open Seat, Spring, and
The Mud Max® Valves and Seats are 100% interchange- “Blue Streak™” High Temperature Valve
able with the Harrisburg Roughneck® style. These seats
are made of premium alloy steel and carburized for sur-
face hardness to resist wear and extend service life. Seat
sealing angle with the valve is 45°.

65
Baker SPD VALVES AND SEATS FOR STANDARD API VALVE POTS

BAKER DOUBLE-ANGLE O-RING VALVES AND SEATS

API-6 API-6
Description API-5 API-7 API-8
Series 02 Series 03
Valve, with Urethane Insert 050011700 050011800 050011900 050011000 050012000
Valve, with “Blue Streak™” High Temperature Urethane Insert 052148700 052058600 052050200 O/A
Insert, Urethane 051584400 051584400 051584500 051427500 051583100
Insert, Urethane High Temperature O/A 052058500 052050100 O/A
Seat 050862300 050481800 052000800 050930900 050484400
O/A = On Application.
Note: For all other pumps, contact your Baker SPD representative.

BAKER STANDARD PLATE TYPE VALVES AND SEATS

API-6 API-6
Description API -4 API-5 API-7 API-8 API-9
Series 02 Series 03
Valve, with Urethane Insert 050828700 050499100 050501200 050503800 050506200 050510900 050511800
Valve, with Lipless Buna-N Rubber Insert 050828200 050498800 050500900 050503400 050505900 050510500 050511300
Insert, Urethane 050488600 050488800 050488800 050489000 050489300 050489700 050490100
Insert, Buna-N Rubber 050485900 050486000 050486000 050486200 050486400 050486800 050487000
Half Retainer (2 pieces required) 050492100 050492000 050492000 050492000 050492000 050492000 050492000
Retainer Ring 050493000 050493100 050493100 050493100 050493100 050493100 050493100
Valve Plate 050490600 050490700 050490700 050490800 050491000 050491300 050491500
Seat 050828100 050862300 050481800 052000800 050930900 050484400 050485100
Note: For all other pumps, contact your Baker SPD representative.

MUD KING® VALVES AND SEATS

100% Interchangeable with Mission
Description API-5 API-6 API-7 API-8
Valve, with Urethane Insert 052101100 052100600 052100000 052107600
Valve, with Buna-N Rubber Insert 052101133 052100633 052100033 052107633
Valve, with “Blue Streak™” High Temperature Urethane Insert 052101122 052100622 052100022 052107622
Insert, Buna-N Rubber 052141200 052107100 052106300 052141300
Insert, Urethane 052101200 052100700 052100100 052107500
Insert, Urethane High Temperature 052101201 052100701 052100101 052107501
Seat 052101500 052100900 052100400 052107200
Note: For all other pumps, contact your Baker SPD representative.

BAKER WM SERIES FULL OPEN VALVES AND SEATS

Description API-6 API-7 API-8
Valve, with Urethane Insert 052045100 052042100 N/A
Valve, with “Blue Streak™” High Temperature Urethane Insert 052090800 052098000 N/A
Insert, Urethane 052043600 052036800 N/A
Insert, Urethane High Temperature 052088700 052088600 N/A
Seat 052044500 052040900 N/A
N/A = Not Available.
Note: For all other pumps, contact your Baker SPD representative.

MUD MAX® FULL OPEN VALVES AND SEATS

100% Interchangeable with the Harrisburg Roughneck
Description API-5 API-6 API-7 API-8
Valve, with Urethane Insert 052082800 052081600 052081300 N/A
Valve, with “Blue Streak™” High Temperature Urethane Insert 052082822 052081622 052081322 N/A
Valve, Full Open with Buna-N Rubber Insert 052082833 052081633 052087900 N/A
Insert, Urethane 052084200 052081500 052080600 N/A
Insert, Urethane High Temperature 052084201 052081501 052080601 N/A
Insert, Buna-N Rubber 052141100 052090600 052087800 N/A
Seat 052082100 052081700 052080500 N/A
N/A = Not Available.
Note: For all other pumps, contact your Baker SPD representative.

66
NON-API MODIFIED SEATS FOR EMSCO/NATIONAL PUMPS Baker SPD

BAKER STANDARD PLATE TYPE VALVES AND SEATS

Non API-6 Non API-6
Description Non API -4 Non API-5 Series 02 Series 03 Non API-7 Non API-8 Non API-9
Pumps Pumps
Valve, with Urethane Insert 050828700 050499100 050501200 050503800 050506200 050510900 050511800
Valve, with Lipless Buna-N Rubber Insert 050828200 050498800 050500900 050503400 050505900 050510500 050511300
Insert, Urethane 050488600 050488800 050488800 050489000 050489300 050489700 050490100
Insert, Buna-N Rubber 050485900 050486000 050486000 050486200 050486400 050486800 050487000
Seat (National 7P50) - 051574500 - - - - -
Seat (National 8P80, 9P100, 10P130) - - - 051243600 - - -
Seat (National 12P160) - - - - 051429900 - -
Seat (National 14P220) - - - - - 050484500 -
Seat (Continental Emsco Pumps) - 050481600 050481800 050482300 050482700 050484300 -
Half Retainer (2 pieces required) 050492100 050492000 050492000 050492000 050492000 050492000 050495000
Retainer Ring 050493000 050493100 050493100 050493100 050493100 050493100 050493100
Valve Plate 050490600 050490700 050490700 050490800 050491000 050491300 050491500
Note: For all other National Pumps contact your Baker SPD representative.

BAKER DOUBLE-ANGLE O-RING VALVE AND SEATS

Non API-6
Description Non API-5 Non API-6 Non API-7 Non API-8
Series 03
Valve, with Urethane Insert 050011700 050011800 050011900 050011000 050012000
Valve, with “Blue Streak™” High Temperature Urethane Insert O/A 052058600 052050200 O/A
Insert, Urethane 051584400 051584400 051584500 051427500 051583100
Insert, Urethane High Temperature O/A 052058500 052050100 O/A

MUD PUMP FLUID END

EXPENDABLE PARTS
Seat (National 7P50) 051574500 - - - -
Seat (National 8P80, 9P100, 10P130) - - - - -
Seat (National 12P160) - - 051243600 051429900 -
Seat (National 14P200/14P220) - - - - 050484500
Seat (Continental Emsco Pumps) 050481600 050481800 050482300 050482700 050484300
O/A = On Application. ; Note: For all other National Pumps contact your Baker SPD representative.

MUD KING® VALVES AND SEATS

100% Interchangeable with Mission
Description Non API-5 Non API-6 Non API-7 Non API-8
Valve, with Urethane Insert 052101100 052100600 052100000 052125800
Valve, with Buna-N Rubber Insert 052101133 052100633 052100033 052125833
Valve, with “Blue Streak™” High Temperature Urethane Insert 052101122 052100622 052100022 052125822
Insert, Buna-N Rubber 052141200 052107100 052106300 052141300
Insert, Urethane 052101200 052100700 052100100 052107500
Insert, Urethane High Temperature 052101201 052100701 052100101 052107501
Seat (National 7P50) N/A - - -
Seat (National 8P80, 9P100, 10P130) - 052101000 - -
Seat (National 12P160) - - 052100500 -
Seat (National 14P200/14P220) - - - 052110900
N/A = Not Available.; Note: For all other National Pumps contact your Baker SPD representative.

BAKER WM SERIES FULL OPEN VALVES AND SEATS

Description Non API 5.5 Non API-6 Non API-7
Valve, with Urethane Insert 052062700 052045100 052042100
Valve, with “Blue Streak™” High Temperature Urethane Insert N/A 052090800 052098000
Insert, Urethane 052059200 052043600 052036800
Insert, Urethane High Temperature N/A 052088700 052088600
Seat (National 7P50) 052059000 - -
Seat (National 8P80, 9P100, 10P130) - 052044400 -
Seat (National 12P160) - - 052041000
Seat (National 14P200/14P220) - N/A N/A
N/A = Not Available.; Note: For all other National Pumps contact your Baker SPD representative.

MUD MAX® FULL OPEN VALVES AND SEATS

100% Interchangeable with the Harrisburg Roughneck
Description Non API-5 Non API-6 Non API-7
Valve, with Urethane Insert 052082800 052081600 052081300
Valve, with “Blue Streak™” High Temperature Urethane Insert 052082822 052081622 052081322
Valve, with Buna-N Rubber Insert 052082833 052081633 052087900
Insert, Urethane 052084200 052081500 052080600
Insert, Urethane High Temperature 052084201 052081501 052080601
Insert, Buna-N Rubber 052141100 052090600 052087800
Seat (National 7P50) 052093200 - -
Seat (National 8P80, 9P100, 10P130) - 052083700 -
Seat (National 12P160) - - 052083500
Seat (14P200/14P220) - - -

67
Baker SPD REPLACEABLE PISTONS

DUPLEX AND TRIPLEX REPLACEABLE RUBBER PISTONS

Baker SPD A-Line Pistons are made with nitrile rubber and the piston's maximum pressure capability is due to
this oil, water and heat resistant material. These pistons are fully interchangeable with most other
manufacturers.
Baker SPD pistons are highly resistant to extrusion wear under the highest pump pressures. The A-Line piston
offers maximum resistance to bending and hoop stresses generated by cylinder loads and rod fits; a benefit of
their premium forged alloy steel bodies. Rated for all drilling operations up to 2,500 psi.

Duplex Replaceable Rubber Piston Assembly Duplex Piston Rubber Assembly

Triplex Replaceable Rubber Piston Assembly Triplex Piston Rubber Assembly

68
BONDED PISTONS Baker SPD

BONDED RUBBER DUPLEX AND TRIPLEX PISTONS

Developed for medium service applications, these pistons are constructed of oil resistant rubber, bonded to a
solid metal hub. This design permits increased movement of the lip and provides a complete liner to piston seal,
even with the enlarged diameter of a worn liner. Rated for all drilling operations up to 2,500 psi.

MUD PUMP FLUID END

EXPENDABLE PARTS
Duplex Bonded Rubber Piston Triplex Bonded Rubber Piston

“DOUBLE DURO” BONDED TRIPLEX URETHANE PISTON

The “Double Duro” Bonded Triplex Urethane Piston is
designed for resistance to extrusion and abrasion, and
with water cooling it will provide optimum performance in
oil base mud and high drilling pressures.
FEATURES
• Rated for all drilling operations up to and exceeding
5,000 psi
• Maximum operating temperature is 170°F
• Extended service life
• High pressure service
“Double Duro” Bonded Triplex Urethane Piston

69
Baker SPD BONDED PISTONS

SINGLE DUROMETER BONDED URETHANE TRIPLEX PISTON

The Single Durometer Bonded Urethane Triplex Piston
was designed for resistance to extrusion and abrasion
and with water cooling, it will provide optimum perfor-
mance in oil base mud and high drilling pressures.
These pistons are highly resistant to extrusion wear un-
der the highest pump pressures.
FEATURES
• Rated for all drilling operations up to and exceeding
5,000 psi
• Maximum operating temperature is 170°F
• Extended service life
Single Durometer Bonded Urethane Triplex Piston
• High pressure service

“BLUE STREAK™” HIGH TEMPERATURE

BONDED URETHANE TRIPLEX PISTON
The “Blue Streak™” High Temperature Bonded Ure-
thane Triplex Piston is a single durometer urethane pis-
ton designed to cover higher temperature and pressure
capabilities. Resistant to extrusion and abrasion, and
with water cooling this piston will provide optimum per-
formance.
FEATURES
• Rated for all drilling operations up to and exceeding
5,000 psi
• Maximum operating temperature is 200°F
• Extended service life “Blue Streak™” High Temperature Bonded Urethane Triplex Piston
• High temperature tolerant
• High tolerant to chemical attack

70
TRIPLEX PISTON MATERIAL NUMBER SCHEME Baker SPD

REPLACEABLE RUBBER TRIPLEX PISTONS

Series 300 and 375
Piston Assembly;
Series ODO Rubber Assembly
Non-Water Cooled Water Cooled
Baker Competitor in. Premium Premium Premium
5 924125014 924115014 052049000
5-1/4 924125214 924115214 052049100
300 Q BQ 5-1/2 924125414 924115414 052047900
5-3/4 924125614 924115614 052049200
6 924126014 924116014 052048000
6-1/4 924146214 924136214 052049300
6-1/2 924146414 924136414 052048100
6-3/4 924146614 924136614 052049400
7 924147014 924137014 052048200
375 Q LQ
7-1/4 924147214 924137214 052049500
7-1/2 924147414 924137414 052049600
7-3/4 924147614 924137614 052063600
8 924148014 924138014 052063700
;Each piston assembly includes Sleeve (052047400) for API SA-4 (1-1/2 in.) rods. Disposal of the Sleeve adapts the piston for applications

MUD PUMP FLUID END

to National (1-5/8 in.) rods.

EXPENDABLE PARTS
OInside Diameter is 1-1/2 in. and 1-5/8 in.
QBaker Series 300 and 375 piston parts are fully interchangeable with competitors’ series B and L parts, respectively.
Piston Seal: O-ring (WW-B225-H30).

BONDED TRIPLEX PISTONS

Size Single Duro Double Duro Bonded Blue Streak™
in. Bonded Bonded Rubber High Temp Bonded
4-1/2 924014414 924024414 924034414 924514414
5 924015014 924025014 924035014 924515014
5-1/2 924015414 924025414 924035414 924515414
6 924016014 924026014 924036014 924516014
6-1/4 924046214 924056214 924066214 924526214
6-1/2 924046414 924056414 924066414 924526414
6-3/4 924046614 924056614 924066614 924526614
7 924047014 924057014 924067014 924527014
7-1/4 O/A O/A O/A O/A
O/A = On Application.

71
Baker SPD DUPLEX PISTON MATERIAL NUMBER SCHEME

REPLACEABLE RUBBER DUPLEX PISTONS

Series 300
Series Piston OD Piston Assembly Rubber Assembly
Baker Competitor Taper in. Premium Premium
5 924255003 052053100
5-1/4 924255203 052053200
5-1/2 924255403 052053300
5-3/4 924255603 052053400
6 924256003 052053500
6-1/4 924256203 052053600
300 Q BQ API-3
6-1/2 924256403 052053700
6-3/4 924256603 052053800
7 924257003 052053900
7-1/4 924257203 052054000
7-1/2 924257403 052054100
7-3/4 924257603 052054200
5 924235004 052053100
5-1/4 924235204 052053200
5-1/2 924235404 052053300
5-3/4 924235604 052053400
6 924236004 052053500
6-1/4 924236204 052053600
300 Q BQ API-4
6-1/2 924236404 052053700
6-3/4 924236604 052053800
7 924237004 052053900
7-1/4 924237204 052054000
7-1/2 924237404 052054100
7-3/4 924237604 052054200
Q Baker Series 300 piston parts are fully interchangeable with competitors’ series B parts.

BAKER SPD DUPLEX PISTONS

Series 300 and 375
Series Piston OD Piston Assembly Rubber Assembly
Baker Competitor Taper in. Premium
4-1/2 924194405 052052900
4-3/4 924194605 052053000
5 924195005 052053100
5-1/4 924195205 052053200
5-1/2 924195405 052053300
5-3/4 924195605 052053400
6 924196005 052053500
API-5/
300Q BQ 6-1/4 924196205 052053600
5 HP
6-1/2 924196405 052053700
6-3/4 924196605 052053800
7 924197005 052053900
7-1/4 924197205 052054000
7-1/2 924197405 052054100
7-3/4 924197605 052054200
8 924198005 052054300
6 924206006 052055300
6-1/4 924206206 052055400
6-1/2 924206406 052055500
6-3/4 924206606 052055600
API-6/
375Q LQ 7 924207006 052055700
6 HP
7-1/4 924207206 052055800
7-1/2 924207406 052055900
7-3/4 924207606 052056000
8 924208006 052056100
QBaker Series 300 and 375 piston parts are fully interchangeable with competitors’ series B and L parts, respectively.

72
PISTON RODS AND PACKING Baker SPD

A-LINE TRIPLEX PISTON ROD

This rod offers excellent resistance to fatigue, corrosion, and high loads thanks to its two step heat treated body
with phosphatized-finished alloy steel. The A-Line Triplex Piston Rod fits all pistons manufactured to API
Standard 7.

A-LINE DUPLEX PISTON ROD

Resisting abrasives, corrosion, fatigue, and high loads better than any piston rod in the oilfield, this rod is
actually a heat treated alloy steel bar fuse coated with a layer of nickel chrome boron. This is a technique first
introduced to the industry by Reed American. Featuring a precision ground OD, and numerically controlled
machining of the ends to tighter than authorized API specifications, this rod fits all pumps in the field. The rod's
excellent fatigue resistance is accentuated by a fully interchangeable, but exclusive, modified thread root
design.

A-LINE DUPLEX ROD PACKING

Withstanding the highest pump pressures, this packing performs best under all drilling conditions. The packing's
semi-adjustable design prevents it from collapsing and allows it to resist high pressure extrusion. This packing

MUD PUMP FLUID END

EXPENDABLE PARTS
resists the elements due to its woven duck fabric and nitrile construction. The packing comes with individual split
rings that are easy to install and to remove. Packing is recommended for service on pumps handling oilwell
drilling muds, fresh water, salt water, and general petroleum products.
Note: Rod clamps are available upon request. Contact your Baker SPD representative for additional informa-
tion.

Piston Rods, Packing, and Clamps

73
Baker SPD LINERS AND LINER PACKING

A-LINE LINERS FOR TRIPLEX

AND DUPLEX PUMPS
The A-Line designation of these liners indicate unmatched perfor-
mance and durability in most severe drilling conditions.
Constructed to a computer designed shrink fit of a high chrome/iron or
bimetal sleeve into a forged steel hull, the liners offer extreme abra-
sion, resistance, hardness, and corrosion resistance. These liners can
withstand the highest hoop stresses since their hulls are made of high-
grade carbon steel forging. All Baker SPD standard liners are manu-
A-Line Liners for Triplex and Duplex Pumps factured with the “HP” lip design to prevent inner sleeve slippage.
Sleeves are 26% chrome steel heat treated to RC62 to 66 hardness.
The micro-finish honed ID helps assure piston durability, yet it is not
so smooth as to produce hydroplaning. The OD is numerically con-
trolled, machined precisely to ensure continually correct registers and
sealing surfaces to the pump bore and face.
Liner bore tolerances, tighter than the API specifications, give approx-
imately 5% to 10% bonus hours of service life to the piston and liner,
over and above the extended service life. Combined with a competi-
tive initial cost factor, this extended liner life makes Baker SPD triplex
and duplex A-Line liners the most cost and performance efficient in the
current industry.

A-LINE PACKING
Recommended for high pressure applications. A-Line liner packing
prevents excessive packing extrusion. This packing has an extrusion
resistant design featuring hard corners which are an integral part of
seal rings. The soft nitrile element rubber center establishes fluid seal,
while the hard corners prevent rubber extrusions into the pump bore
and over liner flange shoulders. Except where noted, lantern rings in-
terchange with those furnished by pump manufacturer or lantern rings
A-Line Packing
used in A-Line liner packing.

VALVE CAP, CYLINDER HEAD, AND PLUG SEAL GASKETS

Molded of oil resistant duck and synthetic composition, these fluid end gaskets are designed to handle all drilling
conditions, and afford positive sealing in all areas of both triplex and duplex mud pumps.
Depending on the design, these gaskets are used as liner packing in many triplex and duplex mud pumps, thus
affording an additional cost savings to the drilling company.

Cylinder Head Seal

Plug Seal

Gaskets

74
SERVICE TOOLS Baker SPD

MECHANICAL VALVE SEAT PULLER

The Baker SPD mechanical seat puller utilizes a screw and wedge principle to 1
produce 200,000 lb of force to pull valve seats safely and easily. The components
2
are made from high quality cast steel for impact and wear resistance.

MECHANICAL VALVE SEAT PULLER

PARTS LIST
3
Item Valve No. Material
Description
No. Series Req’d. No.
- Assembly Complete, Less Head All - 051510200
1 Wing Nut - 1 050551300
2 Plain Washer - 1 050547600
3 Stem - 1 052106100 4
4 Wedge - 1 050547500
5 Grooved Washer - 1 050547700
6 Crowfoot (or Support) - 1 050547800
;Valve Seat Puller Heads - See chart below for listings.
5

MUD PUMP FLUID END

EXPENDABLE PARTS
WEB TYPE AND FULL OPEN VALVE SEAT PULLER HEADS

HYDRAULIC AND MECHANICAL VALVE SEAT PULLER HEAD

6
Mud King® Mechanical Valve Seat Puller
Valve 3-Web WM Full Mud Max®
Description API 4-Web
Series Threaded Open Full Open
Threaded
- 00 051493022 N/A N/A N/A
4 01 051493122 N/A N/A N/A
5 or 6 02 051493222 052102100 052061800 052084100
6 03 051493322 052102200 052119900 052084000
Puller Head
X 03 051493322 052102200 052119900 052084000
7 04 051449922 052102300 052120000 052083900 ;

8 06 051493422 052139100 O/A N/A

9 07 & 08 051493522 N/A N/A N/A
X API Modified Pumps.
N/A = Non-Applicable.
O/A = On Application.
Web Type Valve
Seat Puller Heads

Hydraulic Valve Seat Puller

75
Baker SPD SERVICE TOOLS

HYDRAULIC VALVE SEAT PULLER

14 The Baker SPD Hydraulic Valve Seat Puller was developed for two
12
reasons: to eliminate damage to fluid ends caused by removing valve
3 10
5
seats with a cutting torch, and to reduce the possibility of personal
injury.
9
The puller unit can exert a force of over 200,000 pounds on the valve
11 seat. The unit comes complete with a 25-ft hose so that the hand
operated hydraulic pump can be placed at a safe distance from the mud
6
7
15 pump during pulling operations. The hose, puller unit, and pump are
8
equipped with quick disconnect couplings for easy handling. The pump
comes complete with a pressure gauge. The numerically controlled
machined and heat treated puller heads of high alloy steel offer maxi-
mum strength without the stress concentration characteristic of torch
13 burned heads.
2

Hydraulic Valve Seat Puller 3

1 4 12
7
Hydraulic Pump

HYDRAULIC VALVE SEAT PULLER

Item Valve No.
Description Material No.
No. Series Req’d.
- Assembly Complete, Less Head and Adapter All - 051596902
- Assembly Complete, Less Head, Adapter, and Pump All - 051432200
- Pump Assembly All 1 051596800
1 Pump - 1 051596600
- Pump Repair Kit for Pump Y-22 - - 051596700
- Pump Repair Kit for Pump Y-43 or P-158 - - 051749700
2 Gauge - 1 050551900
3 Hose Coupling, Male - - 050769100
4 Nipple - 1 051561400
- Puller Jack Assembly O All 1 051432601
5 Body - 1 052085300
6 Base - 1 050551400
7 Seal Ring, Small - 1 050551600
8 Seal Ring, Large - 1 050551700
9 Bolt - 3 WWGH1D38SX
10 Elbow, Male - 1 050752200
3 Hose Coupling, Male - 1 050769100
- Hose Assembly All 1 051432700
11 Hose, 25 ft - 1 050750800
12 Hose Coupling, Female - 2 050769000
13 Stem Q - 1 052106100
14 Wing Nut All 1 050551300
15 Tripod Base Adapter (for Studded Pot Covers) - 1 051433300
; Flat Base Adapter (for Pot Covers Opening Larger than 10 in. Dia) - 1 051242800
;Not shown.
O Puller Jack Spare Parts Assembly 0515565.
Q Puller Adapter, competitor stem (2 in. - 4-1/2 in. thread) to Baker puller head with tapered thread, Material No. 0505479.
Q Puller Adapter, Baker stem with tapered thread to competitor head (2 in. - 4-1/2 in. thread), Material No. 0517211.
V Head, see Page 75 for listings.
X For Pullers produced before January 2000 use bolt 050551500.
76
SERVICE TOOLS Baker SPD

HYDRAULIC FULL OPEN VALVE SEAT PULLER (SWIVEL TYPE)

FULL OPEN HYDRAULIC SEAT PULLER

(SWIVEL TYPE)
Item
Description Material No.
No.
1 Stem 052106100
5 Jack 051432601
6 Hose Assembly 051432700
7 Pump Assembly 051596800
8 Wing Nut 050551300
9 Hex Nut 051785100
- Puller Assembly 051596902;
Note: Item No. 2 Puller Head not shown. Refer to page 75 for Puller Head information.
;Consists of items 1 through 8 (Puller Head and Hex Nut sold separately).
O Tripod Base Adapter for studded pot covers.

MUD PUMP FLUID END

EXPENDABLE PARTS
8

6
O

Hydraulic Pump

Hydraulic Full Open Valve Seat Puller (Swivel Type)

77
Baker SPD SERVICE TOOLS

VALVE INSERT INSTALLATION TOOL

(PLATE TYPE/DOUBLE ANGLE)
Although originally developed to change inserts on Baker SPD valves, this
4
installation tool has been modified to work on other valve inserts, too. The body
is of sturdy construction from a one piece steel casting. The adjusting screw
provides compression of the insert needed for easy slip fit of the retainer under
1
the shoulder and on the top stem of the valve.

3 Installation plates control insert twist when replacing Double Angle O-ring
inserts.

VALVE INSERT INSTALLATION TOOL

2
Item Valve No. Material
Description API
No. Series Req’d No.
- Assembly Complete, Less Plates - 050844300
1 Body 1 050844400
Valve Insert Installation Tool 2 Screw 00-07 All 1 050844500
3 Pressure Shoe 1 050019200
4 Retainer Pin 1 050619800

VALVE INSERT INSTALLATION PLATES

Item Valve No.
Description API Top Bottom
No. Series Req’d;
01 4 - N/A N/A
02 5, 6 2 050019500 050019400
5 03 - 2 050020800 050020700
5 Plates, D/A O-ring Valve Only
04 7 2 050019700 050019600
06 8 2 050020200 050020100
07 9 - N/A N/A
5 ;One top and one bottom plate required.

VALVE INSERT INSTALLATION FIXTURE

(WM FULL OPEN STYLE)
Item No. Material
Description API
No. Req’d No.
5.5 1 052060500
1 Installation Fixture 06 1 052044900
Valve Insert Installation Plate
07 1 052040100
Use heavy duty vise-10 in. minimum opening.

VALVE INSERT
INSTALLATION FIXTURE
FOR MUD MAX® FULL OPEN
No. Material
Description API
Req'd No.
1 Insert 5 1 O/A
Installation 6 1 052085400
Fixture 7 1 052085500
O/A = On Application.

Valve Insert Installation Tool

Valve Insert Installation Fixture

78
FIELD REPLACEMENT INSTRUCTIONS Baker SPD

INSTRUCTIONS FOR THE FIELD REPLACEMENT OF

BAKER DOUBLE ANGLE O-RING VALVE INSERT
PREPARATION OF VALVE
1. Secure valve flange in a bench vise as shown, and cut off insert with any sharp
tool or 500° maximum heat source.
2. Clean valve cone and insert groove with any hydrocarbon based solvent. File Step No. 1 and 2
smooth any rough or chipped surfaces on the valve cone. Reduce all sharp edg-
es to a 1/64 in. minimum radius. THIS IS IMPORTANT! Wipe clean and dry.
3. With valve upside down and the cone plate positioned as shown, dimension “X” X
must be greater than zero (0) to qualify for subsequent installation of a new insert.
PREPARATION OF FIXTURE
4. Secure Installation Tool #508443 with a socket type shoe in a vise with the bolt
on top, as shown.
5. Apply a light coat of clean medium weight bearing grease to all surfaces indicated
by dotted lines. (Cone and groove of body. Top, inside, and bottom of insert.
Step No. 3
Cone of top plate, face of bottom plate.)

MUD PUMP FLUID END

6. Assemble as shown, being certain that the outside cone of the insert is pointed

EXPENDABLE PARTS
down, as shown, and that the insert is seated on the centering ridge of the instal-
lation plate. The insert must be concentric with the installation plate. THIS IS IM-
PORTANT!
INSERT INSTALLATION
7. Tighten the bolt two full turns. Recheck insert/plate concentricity. If no eccentric-
ity exists, continue to tighten the bolt to insert installation.
8. If eccentricity exists after two turns (#7 above), back off the bolt and reestablish
insert/plate concentricity before proceeding.
Note: Past experience has shown that turning the bolt by hand has not been very
efficient in assembling inserts. What has proven to be very efficient is the use of an
air wrench. If at all possible, this is the assembly procedure that is recommended to
be used when installing inserts.
INSERT SEATING
9. USE A PLASTIC OR WOODEN MALLET. DO NOT USE A METALLIC HAMMER.
Mallet the minor cone of the insert at one point until insert/groove alignment is ob-
tained, then seat the insert evenly into the groove all around. DO NOT USE A STEEL
HAMMER.
Step No. 4, 5, 6, and 7
STORAGE
10. To protect the plates from loss and damage while in storage, place a used valve
into the nested cone and installation plates. Place this assembly into the installa-
tion tool and tighten the socket shoe onto the valve top stem to form a unitized
assembly.
Use a plastic or wooden mallet. DO NOT USE A METALLIC HAMMER.

Step No. 9 Step No. 9

79
Baker SPD FIELD REPLACEMENT INSTRUCTIONS

INSTRUCTIONS FOR THE FIELD REPLACEMENT OF

BAKER FULL OPEN VALVE INSERT
PREPARATION OF VALVE
1. Secure valve stem in a bench vise as shown, and cut off insert with any sharp tool
or 500° maximum heat source.
2. Clean valve cone and insert groove with any hydrocarbon based solvent. File
smooth any rough or chipped surfaces on the valve cone. Reduce all sharp edges
to a 1/64 in. minimum radius. THIS IS IMPORTANT! Wipe clean and dry.
PREPARATION OF FIXTURE
3. Apply a light coat of clean medium weight bearing grease to all surfaces indicated
Step No. 1 and 2
by dotted lines. (Cone and groove on body. Top, inside, and bottom of insert.
Face of installation plate.)
4. Assemble in a bench vise as shown, being certain that the minor cone of the in-
sert is seated as shown, on the centering ridge of the installation plate. The insert
must be concentric with the installation plate. THIS IS IMPORTANT!
NOTE: Use vise with jaw opening of no less than 10 in. Vise handle must be no less than
1 in. in diameter.

INSERT INSTALLATION
5. Tighten the vise two [2] full turns. Recheck insert/plate concentricity. If no eccen-
tricity exists, continue to tighten the vise to insert installation.
6. If eccentricity exists after two [2] turns (#5 above), back off the vise and reestab-
lish insert/plate concentricity before proceeding. As vise is tightened more, load
will increase until tightening by hand will no longer be possible. At this point, use
a 5 ft “cheater” pipe on the vise handle will move the insert to installation.
NOTE: The installation plate will go metal to metal against the cone of the body. If the
insert has not rolled over into the groove in the body, place a mallet against the edge
of the insert and with another mallet, hit the first mallet until it drives the insert over
the edge of the body and into the groove. The insert will appear completely distorted.
Remove this assembly from the vise. Remove the installation plate from the body.
Step No. 3, 4, 5, and 6 INSERT SEATING
7. USE A PLASTIC OR WOODEN MALLET. DO NOT USE A METALLIC HAM-
MER. Mallet the minor cone of the insert at one point until insert/groove alignment
is obtained, then seat the insert evenly into the groove all around. DO NOT USE
A STEEL HAMMER. Insert should extend over edge of body cone at least 1/32
in. If any area of insert is larger, continue to use mallet until insert is even all
around.

Use a plastic or wooden mallet.

DO NOT USE A
METALLIC HAMMER.

Step No. 7

80
MUD PUMPS Baker SPD

MUD PUMP CHARTS

Manufacturer API-4 API-5 API-6 API-7 API-8 API-9
B-1000-T (7 x 10) B-1300-T (7 x 12) B-500 (7-1/2 x 14) B-750-C (7-3/4 x 16)
B-1600-T (7 x 12) B-750-F (7 x 16)
Brewster
B-1000-F (7 x 18)
B-550-F (7 x 14)
F-350-P (4-1/2 x 7) F-350 (6 x 7) D-125 (7-1/4 x 10) BA-14; (7-1/2 x 14) D-550 (7-1/2 x 16) D-700 (8 x 16)
F-500 (6 x 7-1/2) D-225 (7-1/4 x 12) CA-16; (7-1/2 x 16) D-850 (8-1/4 x 18) D-1000 (8-1/4 x 18)
F-650 (6 x 8) F-800 (6-1/4 x 9) D-14; (7-1/2 x 14) DA-500 (7-1/2 x 16) D-1250 (7-1/2 x 18)
F-750 (6-3/4 x 8) F-1000 (6-1/4 x 10) D-16; (7-1/2 x 16) DB-550 (7-1/2 x 16) D-1350 (7-1/2 x 18)
FA-750 (6-3/4 x 8) D-300; (7-1/2 x 14) DB-700 (7-1/2 x 16) D-1500 (7-1/2 x 18)
D-375; (7-1/2 x 14) DC-850 (7-1/2 x 18) D-1650 (7-1/2 x 18)
D-500; (7-1/2 x 16) DC-1000 (7-1/2 x 18) D-1000-A (8-1/4 x 18)
Continental
F-1300 (7 x 12) DC-1350 (7-1/2 x 18) DA-700 (8-1/4 x 16)
Emsco
F-1600 (7 x 12) DC-1650 (7-1/2 x 18) DA-850 (8-1/4 x 18)
FA-1300 (7 x 12) FC2200 (7 x 12) DB-1000 (7-1/2 x 18)
FA-1600 (7 x 12) FC1600 (7 x 12) DB-850 (7-1/2 x 18)
FA-1300 II (7 x 12)
FA-1600 II (7 x 12)
FB-1300 (7 x 12)
FB-1600 (7 x 12)
WH-440 WH-770 W-1500 15W-600 (7 x 16)
W-600
W-446 SF WH-550 W-1712 16W-800
W-800
W-1714 W-3000
W-850
W-2214
Ellis W-1100
W-2215
Williams WH-600
14W-400
9W-1000
WH-1300
WH-1000
WH-1600
WHD-1000
WH-2200
PJ-8A (5 x 8) PO-7E (6-1/4 x 7) PZX (7 x 11) PY-7B (7 x 7) FK-FXK (7-1/4 x 14) FQ-FR (7-3/4 x 18)
PJ-HB (5 x 8) PV-9A (6-1/4 x 9) PX11 (7 x 11) PY-7D (7 x 7) GN-GXN (7-1/4 x 14) GH-GXH (7-3/4 x 18)
PAH-AD (4-1/2 x 8) PY-7A (6-1/4 x 7) PY-7F (7 x 7) GN-GXN-A (7-1/4 x 14) FQ-FXQ (7-3/4 x 16)
PAH-AE (4-1/2 x 8) PY-7C (6-1/4 x 7) PZ-8 (Newstyle) (7 x 8) GQ-GXN (7-1/4 x 14) GP-GXR (7-3/4 x 18)

MUD PUMP FLUID END

PAH-AJ (4-1/2 x 8) PY-7E (6-1/4 x 7) PZ-JC,D(9) (7 x 9) GQ-GXN-A (7-1/4 x 14) GR-GXR (7-3/4 x 18)

EXPENDABLE PARTS
Gardner PAH-AK (4-1/2 x 8) PY-7G (6-1/4 x 7) PZ-10,PZK (7 x 10) GQ-GXN-B (7-1/4 x 14) GP-GXP-A (7-1/2 x 16)
Denver PZ-8A (6-1/4 x 8) PZ-HE,VE(8) (7 x 8) GQ-GXN-C (7-1/4 x 14) GR-GXP-A (7-1/2 x 16)
PZ-HB,D (6-1/4 x 8) PZLB,C,D,E(11) (7 x 8) GQ-GXN-D (7-1/4 x 14) KG-KXG-A (7-3/4 x 18)
PZ-9A,B (6-1/4 x 9) PZ-7 (7 x 7) GQ-GXQ (7-1/4 x 16) KG-KXG-B (7-3/4 x 18)
PZGA (7 x 7) KJ-KXJ-B (7-1/4 x 18) KG-KXG-C (7-3/4 x 18)
FXNDMA (7-1/4 x 14) KG-KXF-A,B,C (7-3/4 x 16)
KJ-KXJ-A (7-1/4 x 18)
GA-550 (7-1/4 x 14)
Great American
GA-750 (7-1/4 x 16)
MM-200 (6-3/4 x 10) MM-300-A (7-1/4 x 12) MM-550-F, MM-1000-A,B (8 x 16)
T-1000 (7 x 10) MM-300-B,GB (7-1/4 x 12) FB,FC (7-1/4 x 15) MM-1000-F (7-1/2 x 16)
T-800 (6-3/4 x 9) MM-450 (7-1/4 x 12) MM-600-D (7-3/4 x 16) MM-1000-FA (7-1/2 x 16)
T-500 (7 x 8) T-1600 (7-1/2 x 12) MM-600-F (7-1/4 x 16) MM-1000-GB (7-1/2 x 16)
T-1300 (7-1/2 x 12) MM-700-A (7-3/4 x 16) MM-1250-A,B (8 x 18)
MM-700-F (7-1/4 x 16) MM-1250-F (7-1/2 x 18)
Ideco
MM-1250-FA (7-1/2 x 18)
MM-1250-FC (7-1/2 x 18)
MM-1250-GB (7-1/2 x 18)
MM-1450-F (7-1/2 x 18)
MM-1650-F (7-1/2 x 18)
MM-1750-F (7-1/2 x 18)
T-380-A (7-1/4 x 12)
T-380-B (7-1/4 x 12)
T-380-S (6-3/4 x 12)
Ideco Clark T-440-A (7-1/4 x 12)
T-440-B (7-1/4 x 12)
T-440-C (7-1/4 x 12)
T-440-D (7-1/4 x 12)
7-P-50V (6-1/4 x 7) KSH-180 (6x10) K-180 (7-1/4 x 10) C-250-F (7-1/4 x 15) C-350 (7-3/4 x 18)
KSH-280 (6 x 12) K-280 (7-1/4 x 12) K-500 (7-1/2 x 15) C-350-F (7-1/4 x 18)
K-380 (7-1/4 x 12) K-500-A (7-1/4 x 15) G-1000-C (7-3/4 x 16)
National 8-P-80;V (6-1/4 x 8-1/2) K-700-A (7-1/4 x 16) H-850-A (8 x 15)
9-P-100;V (6-3/4 x 9) 14P200 (9 x 14) H-1250 (7-3/4 x 16)
10-P-130;V (6-3/4 x 10) 14P220 (9 x 14) K-700 (8 x 16)
12-P-160V (7-1/4 x 12) G-700-F (7-3/4 x 14)
350-PT (7 x 8) A-850-PT (7-1/2 x 9) 1400-P (7 x 18) A-700-P (7-3/4 x 16)
A-560-PT (7 x 8) 850-PT (6-1/2 x 9) 1700-P (7 x 18) A-850-P (7-3/4 x 16)
A-600-PT (7 x 8) 1100-PT (6-1/2 x 10) A-1000-P (7-3/4 x 18)
1400-PT (6-1/2 x 10)
Oilwell
1700-PT (6-1/2 x 12)
A-1400-PT (7-1/2 x 10)
A-1700-PT (7-1/2 x 12)
A-1100-PT (7-1/2 x 10)
500-DC (6-1/2 x 8) 1000-HDL (7-1/2 x 10)
700-DL (7 x 8)
OPI
700-HDL (7 x 8)
500-AWS (2-3/4 x 3-1/4)
600 (6-1/2 x 14) 1250 (7 x 18)
Wilson 900 (6-1/2 x 16) TITAN (7 x 18)
GIANT (7-1/2 x 14)
C-12 (6 x 12) D-500 (7-1/2 x 16) D-500 (7-1/2 x 16) D-700 (8 x 16)
D-300 (7-1/2 x 14) D-850 (8-1/4 x 16) D-1000 (8-1/4 x 18)
Mattco DA-500 (7-1/2 x 16) D-1350 (7-1/2 x 18)
Continental DB-700 (7-1/2 x 16) D-1650 (7-1/2 x 18)
Emsco DC-850 (7-1/2 x 18) DA-700 (8 x 16)
DC-1000 (7-1/2 x 18) DA-850 (8-1/4 x 18)
DB-1000 (7-1/2 x 18)
G-300 (7-1/4 x 16) B-1640 (8 x 16)
G-45 (8 x 16)
Mattco Emsco
G-65 (8 x 16)
“B” Line
GCI-325-OB (8 x 16)
GCI-450-OB (8 x 16)
;Serial numbers 237 thru 1633.
OSerial number 1634 and continuing upward.
QCheck valve pots, may be original specifications. API-8 or API-9.
VModified API.

81
Baker SPD MUD PUMPS

MUD PUMP CHARTS (Continued)

Manufacturer API-4 API-5 API-6 API-7 API-8 API-9
PJ-8H (5 x 8) PO-7 (6 x 7) FK-FXK (6-1/2 x 14) GQ-GXN-7 (7-1/4 x 14) GR-GXP (7-1/4 x 16)
PV-9 (6 x 9) GQ-GXQ (7-1/4 x 16) GR-GXR (7-1/4 x 18)
Mattco
PY-7 (6 x 7) KJ-KXJ-B (7-1/4 x 18) KG-KXF (7-3/4 x 16)
Gardner
PZ-8 (6 x 8) KG-KXG (7-3/4 x 18)
Denver
PZ-9 (6 x 9)
FZ-FXZ (6 x 12)
MM-600-B (7-1/4 x 16) MM-1250-F (7-1/2 x 18)
MM-600-F (7-1/4 x 16) MM-1250-GB (7-1/2 x 18)
Mattco
MM-700-G (7-1/4 x 16)
Ideco
MM-1000 (7 x 16)
MM-1250 ( 7 x 18)
C-150 (6 x 12) C-150-B (7-1/4 x 12) C-250O (7-1/4 x 15) C-250; (7-1/4 x 15) C-350 Q (7-3/4 x 18)
C-350Q (7 x 18) G-700 (8 x 14)
Mattco National K-500 (7-1/2 x 15) E-500 (8 x 14)
K-700-A (7-1/4 x 16) H-850-A (8 x 15)
H-1250 (7-3/4 x 16)
G-1000-B (7-3/4 x 16)
612-P (6 x 12) 214-P (6-1/2 x 14) 214-P (7-1/4 x 14) 218-P (7-1/4 x 18) A-700-P (7-3/4 x 16)
Mattco 700-P (7 x 16) A-850-P (7-3/4 x 16)
Oilwell 1000-P (7-1/4 x 18) A-1000-P (7-3/4 x 18)
818-P (7-1/4 x 18)
Mattco HP-16000 (7 x 16) HP-18000 (7-3/4 x 18)
Wheland HP-18000 (7 x 18)
F-1000 (6-1/4 x 10) D-700 (6-1/2 x 16)
DB-700 (6-1/2 x 16)
Southwest DA-700 (6-1/2 x 16)
Emsco D-550 (6-1/2 x 16)
DB-550 (6-1/2 x 16)
DA-550 (6-1/2 x 16)
C-250 (6-1/2 x 15) G-1000-C (7-3/4 x 16)
Southwest
C-350 (6 x 18) H-1250 (7-3/4 x 16)
National
N-900 (6-1/2 x 16)
Southwest
All 7500
(All 7500
Fluid Ends
Fluid Ends)
Southwest GR-GXR (6-1/2 x 18)
Gardner GP-GXP (6-1/2 x 16)
Denver GQ-GXQ (6-1/2 x 16)
Southwest 218-P (6-1/2 x 18)
Oilwell 18P (6-1/2 x 18)
TPK-1300 (7 x 10)
Wirth
TPK-1600 (7 x 12)
;Serial numbers 237 thru 1633.
OSerial number 1634 and continuing upward.
QCheck valve pots, may be original specifications. API-8 or API-9.
VModified API.

82