DIGITAL INDICATOR

USER’S MANUAL
DN-10W (VER 5.0)
DN-20W (VER 5.0)
DN-25W (VER 1.0)
DN-30W (VER 1.0)
DN-50W (VER 1.5)

Address : 681-1 Cheoksan-Ri, Nami-Myeon, Cheongweon-Gun,

Chung-buk
TEL :82-43-260-2242
FAX : 82-43-260-2245
http://www.dacell.com
E-Mail : [email protected]
 Contents
1. Features ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 2
1-1. Calibration method ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 2
1-2. HOLD & PEAK HOLD ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 2
1-3. Comparison Output ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 2
1-4. Data Back-up ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 2
1-5. Watch dog ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 2
2. Attention ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 3
2-1. Attention for installation ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 3
2-2. Attention for use ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 3
3. Specif ication ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 4
4. Front Panel ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 5
5. Rear Panel ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 6
6 . W i r i n g D i a g r a m ⋅ ⋅ ⋅ ⋅ ⋅⋅ ⋅ ⋅ ⋅ ⋅⋅ ⋅ ⋅ ⋅⋅ ⋅ ⋅ ⋅ ⋅ ⋅ ⋅⋅ ⋅ ⋅ ⋅⋅ ⋅ ⋅ ⋅⋅ ⋅ ⋅ ⋅ ⋅ ⋅⋅ ⋅ ⋅ ⋅ ⋅⋅ ⋅ ⋅ ⋅⋅ ⋅ ⋅ ⋅ ⋅ ⋅⋅ ⋅ ⋅ ⋅ ⋅⋅ ⋅ ⋅ ⋅⋅ ⋅ ⋅ ⋅ ⋅ ⋅⋅ ⋅ ⋅ ⋅ ⋅⋅ ⋅ ⋅ ⋅⋅ ⋅ ⋅ ⋅ ⋅ ⋅⋅ ⋅ ⋅ ⋅ ⋅⋅ ⋅ ⋅ ⋅⋅ ⋅ ⋅ ⋅ 8
1) DN-10W, DN-50W ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 8
2) DN-20W ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 8
3) DN-25W ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 9
4) DN-30W ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 9
5) External Input ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 9
7. How to use Hold mode ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 10
7-1. How to use comparison output function ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 12
8. S e t ti n g m od e ⋅ ⋅⋅⋅⋅ ⋅⋅⋅ ⋅⋅⋅ ⋅⋅⋅⋅ ⋅ ⋅⋅⋅⋅ ⋅⋅⋅ ⋅⋅⋅ ⋅⋅⋅⋅ ⋅ ⋅⋅⋅⋅ ⋅⋅⋅ ⋅⋅⋅ ⋅⋅⋅⋅ ⋅ ⋅⋅⋅⋅ ⋅⋅⋅ ⋅⋅⋅⋅ ⋅⋅⋅ ⋅ ⋅⋅ ⋅⋅ ⋅⋅⋅ ⋅⋅⋅⋅ ⋅⋅⋅ ⋅ ⋅⋅⋅⋅ ⋅⋅⋅ ⋅⋅⋅⋅ ⋅⋅⋅ ⋅ ⋅⋅⋅⋅ 14
1) DN-10W, DN-50W ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 14
2) DN-20W ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 15
3) DN-25W ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 16
8-1. Function mode (Function Set-up) ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 17
1) How to set up Function ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 17
2) How to set up Relay out data ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 18
3) Function mode table ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 19
8-2. Digital calibration (Calibration by sensor output value) ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 26
1) DN-10W, DN-50W ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 26
2) DN-20W ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 27
8-3. Actual load calibration (Calibration by standard weight) ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 28
1) DN-10W, DN-50W ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 28
2) DN-20W ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 29
3) DN-25W ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 30
8-4. SPAN constant calibration ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 31
1) DN-10W, DN-50W ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 31
8-5. Lock Set up⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 32
9. Product Inspection ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 33
10. OPTION (OP-02, OP-03)
Option 02 (RS232C) ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 34
Option 03 (RS485) ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 36
1
1. Features

We thank you for using our product. Please refer to this manual or contact our office if
you find any problems during using our product.
This product is an indicator that emplifies the micro voltage signals from each sensor
and display in digital. It is mainly used to measure physical quantities of the items using
strain guage such as loadcell, pressure sensor, displacement sensor and torque sensor.
This product has the following special features.

1-1. Calibration Method

2 types of calibration systems are adopted. Calibration by actual load (standard
weight) and calibration by rated output of sensor .

1-2. Hold & Peak Hold

You can choose peak hold or sample hold .

1-3. Comparison Output

You can do set-up the maxium and lower limit value by the keys on the front panel
and output contact point signal of the rear panel.

1-4. Data Back-up

All the set-up values will be memorized on the flash memory so the inputted data can
be saved and no need to do the re-setting even in case of the interruption of the
electric power or power disconnection.

1-5. Watch dog

This function is for automatic reset in case the system is stopped due to the external
factors such as noise.

2
2. Attention
For the efficient and safe use, please carefully read and be fully aware of the
following details before using this product.
It is strictly forbidden to use this product for any other purpose of use or to attempt to
make any alteration on this product.

2-1. Attention for installation

• Please keep it out of wet places.

• Do not set it up near vibration & impulse, high temperature and humidity.
Keep it out of the direct rays of the sun. Set it up where there is less dust, and Keep
it out of direct air including salt and ion.
• Do not use when there is inflammable gas or heavy machinery, and smog.
• Ground earth-terminal ( ).
• Make wire separately from power system wiring and noise wiring.
• Make sure the use of 4 line sealed cable as a sensor cable. Too long cable leads to
measurement error due to wiring resistance (around 10meters).

2-2. Attention for use

During calibration, Do not input free-load state and real-weight load until it becomes
stable. Pressing Enter Key in unstable condition leads to calibration error.

Do not press any Key in use at one's discretion. Please refer to 7. Setting-up mode for
the function and method of Key.

3
3. Specification
Specification model DN-50W DN-10W DN-20W DN-25W DN-30W
0~10V,
SIGNAL 1 ~ 3mv/V 0~2Vrms pulse
4~20mA

ANALOG OUT 0 ~ 10V, 4 ~ 20mA (according to customer request)

EXCITATION 5V 10V, 24V 2Vrms/5kHz 12V

Pressure sensor, Differential PROXIMITY

Strain Gauge sensor
resistance trans SENSOR (MP-
Available sensor (Bridge 120Ω, 350Ω,
displacement displacement 981), ROTARY
700Ω)
meter, sensor (LVDT) ENCODER

MAX. Display -19999 ~ +99999 0~60000

24bit
A/D Converter 16bit 100times/sec -
1000times/sec
16bit
D/A Converter 12bit
1000times/sec

Temperature ZERO 0.5㎶/℃

Characteristic SPAN 50pm/℃
Measured value
7segment LED 14mm
display

Status display LED Red LED 3PCS

Key Switch 4 PCS

Comparison output Hi, Lo, OK OUTPUT (4 relay)

Contact Capacity AC250V 5A

Temperature
-10℃~ 60, >80% RH (No dewing)
range for use
Weight 450g 800g
AC 90~240V
Power supplay AC 220V 50/60Hz(AC110V,DC24V: customer request)
50/60Hz
OP-01 : BCD OUTPUT, OP-02 : RS232C, OP-03 : RS485
OPTION
OP-05 : 8 step open collector output
External dimension 96×48×128 mm (W×H×D)

Panel cutting size 91.5×44.5 mm

4
4. Pront Panel (common feature)

① HI, LO Indication LED

: Hi or LO LED will be lighted when measured value exceeds the setting value.
② HOLD indication LED
: This LED will be lighted when the measured value is on Hold.
③ Measured value Indication
: It indicates the measured value and each setting value.
④ ZERO/SPAN setting up VR
: It is used when ZERO and SPAN calibration of Analog output (DC 0 ~ 10V or 4 ~
20mA) is carried out.
⑤
Measruing Mode : Once this Key is pressed for more than 1 second, the current
measuring value will be Zero (0) and the Analog output will be 0V (4mA) as well.
SET-UP Mode : Once this is pressed on the Function Set-up Mode, you will
return to the measuring mode.
⑥
Measuring Mode : Once this Key is pressed, the lower limit setting value will be
displayed and this value also can be changed.
SET-UP Mode : The location of row for the number flickering can be moved.
⑦
Measuring Mode : Once this Key is pressed, the upper limit setting value will be
displayed and the value can be changed.
SET-UP Mode : The flickering number will be increased by 1 and 1.
⑧
Measuring Mode : Once this Key is pressed, HOLD will be selected and once this
key is pressed again, HOLD will be cancelled.
SET-UP Mode : Save each set-up value.

5
5. Rear Panel (common feature)

Please check the location of terminal and its use. While the projected button is being
pressed, please insert the cable into the lower hole completely. As soon as you release
the button, the connection will be completed. At the point, please slightly pull the calbe
and check whether the cable is come off or not.
(The most suitable calbe is Φ 0.5~1. Linking cable must be brazing or used with I
terminal)

① AC IN : Main Power Supply Wiring Terminal

② : Ground Terminal (as an independent ground connection.)
③ OUT : Analog (DC 0 ~10V/DC 4 ~ 20mA) Output Terminal
④ EXC+ : Sensor Supply Voltage + Connection Terminal
⑤ EXC- : Sensor Supply Voltage + Connection Terminal
⑥ SIG+ : Sensor Ouput Signal + Connection Terminal
⑦ SIG- : Sensor Output Signal – Connection Terminal
⑧ GND : SHIELD connection terminal of sensor
⑨ GND, TXD, RXD : RS232C SERIAL INTERFACE (RS485 : TXD → TX+, RXD → TX-)
⑩ GND : External Input Common Terminal
⑪ IN1 : External HOLD Input Terminal
⑪ IN1 : External HOLD Input Terminal
⑫ IN2 : External ZERO Input Terminal
⑬ IN3 : External printer signal Input Terminal (when PT-100 use)
⑭ IN4 : No use
⑮ COM : RELAY Output Common Terminal
6
⑯ RY1 : RELAY 1(Lower Limit) Output Terminal
○
17 RY2 : RELAY2 (Upper Limit) Output Terminal
○
18 RY3 : RELAY3( Normal) Output Terminal (OK )
○
19 RY4 : RELAY 4 Output Terminal
○
20 ANALOG OUT LOW PASS FILTER Selet Switch

(DN-10W,DN-25W,DN-30W,DN-50W)
SW1 : 10Hz
SW2 : 100Hz
SW3 : 1kHz
○
20 DN-20W Sensor supply voltage & sensor output select switch

Sensor supply voltage setting Sensor output signal setting

10V 24V Voltage type Current type
SW1 ON OFF - -
SW2 OFF ON - -
SW3 - - OFF ON

7
6. Wiring Diagram

1) DN-10W, DN-50W

2) DN-20W

8
3) DN-25W

4) DN-30W

5) External input PLC connection

9
7. How to use Hold mode
Hold mode is largely divided into Peak Hold and Sample Hold. Please select Analog,
Digital or Display Hold as per your purpose of use (Hi or Low Speed)
To input Hold, you can use Hold key on the front panel or external input. For the
operation method, please refer to the drawing below.

DN-10W, DN-20W, DN-25W

1) Peak Hold : To Hold the maxium value among the measured values.
Peak hold mode : It is to hold and display the maximum value of (+) direction.
Absolute peak hold mode : It is to hold and display the maximum value of the
absolute value (+/-).
2) Sample hold : It is to hold and display the value at the time of Hold signal input
among the measured values.

DN-30W
1) Peak hold : To Hold the maxium value among the measured values.
· Peak hold mode : It is to hold and display the maximum value of (+) direction.
2) Sample hold : It is to hold and display the value at the time of Hold signal input
among the measured values.

DN-50W
1) Peak Hold : To Hold the maxium value among the measured values.
Analog peak hold mode : It is a high-speed Peak hold. It is to hold and display the
maximum value of (+) direction.
Display peak hold mode : It is a low-sped Peak hold. It is to hold and display the
maximum value of (+) direction.
Absolute peak hold mode : It is a low-speed Peak hold. It is to hold and display the
maximum value of the absolute value (+/-).
2) Sample hold : It is to hold and display the value at the time of Hold signal input
among the measured values.
Digital sample hold mode : It is operated by high-speed sample hold.
· Display sample hold mode : It is operated by low-speed sample hold.

10
 M M
e e
② ①
a a
s s
u
r u
e r
e
① − : Sensor input value ②
d d
v v
a a
② − : Display value & ①
l
u l
u
e e
Analog ouput value

Time Time

On
Front Panel HOLD LED
Off

External HOLD Input On

Off
Terminal

On
Front Panel HOLD Key off

<Peak HOLD> <Sample HOLD>

11
 7-3. How to use comparison ouput function

For comparison output function, there are 3 different modes such as Decision, High
limit, Low limit. It displays through the relay of rear panel comparing each setup value.
On High limit and Low limit mode, Hysteresis can be used.
To set up upper limit (High) and lower limit(Low), please use the key on the front panel.

1) Decision mode : Measured Value ≤ Lower limit setup value ⇒ RY1 ON (HI)
Measured Value ≥ Upper limit setup value ⇒ RY2 ON (LO)
Lower limit setup value < Measured value < Upper limit setup
value ⇒ RY3 ON (OK)
2) High limit mode : Measured Value ≥ RY1 setup value ⇒ RY1 ON
Measured Value ≥ RY2 setup value ⇒ RY2 ON
Measured Value ≥ RY3 setup value ⇒ RY3 ON
Measured Value ≥ RY4 setup value ⇒ RY4 ON
Measured Value < RY1 setup value – Hysteresis value⇒ RY1 OFF
Measured Value< RY2 setup value - Hysteresis value⇒ RY2 OFF
Measured Value < RY3 setup value – Hysteresis value⇒ RY3 OFF
Measured Value< RY4 setup value - Hysteresis value⇒ RY4OFF
3) Low limit mode : Measured Value ≤ RY1 setup value ⇒ RY1 ON
Measured Value ≤ RY2 setup value ⇒ RY2 ON
Measured Value ≤ RY3 setup value ⇒ RY3 ON
Measured Value ≤ RY4 setup value ⇒ RY4 ON
Measured Value > RY1 setup value + Hysteresis value⇒ RY1 OFF
Measured Value > RY2 setup value + Hysteresis value⇒ RY2 OFF
Measured Value > RY3 setup value + Hysteresis value⇒ RY3 OFF
Measured Value > RY4 setup value + Hysteresis value⇒ RY4 OFF
4) Low & High limit mode
Measured Value ≤ RY1 setup value ⇒ RY1 ON
Measured Value ≤ RY2 setup value ⇒ RY2 ON
Measured Value ≥ RY3 setup value ⇒ RY3 ON
Measured Value ≥ RY4 setup value ⇒ RY4 ON
Measured Value > RY1 setup value + Hysteresis value ⇒ RY1 OFF
Measured Value > RY2 setup value + Hysteresis value ⇒ RY2 OFF
Measured Value < RY3 setup value - Hysteresis value ⇒ RY3 OFF
Measured Value < RY4 setup value - Hysteresis value ⇒ RY4 OFF

12
13
8. Setting Modes

1) DN-10W, DN-50W

For Setting mode, there are 4 different types of mode such as Function mode, Digital
calibration mode, Actual load calibration mode and SPAN constant calibration mode

Measuring Mode

While key is being

pressed, press key.

Function mode
①

END

Digital calibration
②
mode

END

Actual load
③
calibration mode
END

SPAN constant
④
calibration mode
END

① Function mode: Access to each function setup mode. Please refer 8-2 Function
Mode.
② Digital calibration mode: It is to calibrate into the sensor’s output value. No need
to prepare for the actual load (standard weight). Please refer 8-3 How to calibrate.
③ Actual load calibration mode: It is to calibrate by adding the actual load (Standard
weight or the load you know). Please refer 8-4 How to calibrate.
④ SPAN constant calibration mode: It is to calibrate with the S.CAL value written
down for load calibration. Please refer 8-5 How to calibrate.

14
 2) DN-20W

For setting mode, there are 3 different types of mode such as Function mode, Digital
calibration mode, Actual load calibration mode.

Mesuring mode

While key is being

Press, press key

Function mode
①

END

Digital calibration
②
mode

END

Actual load
③
calibration mode
END

① Function mode
Acess to each function setup mode. Please refer 8-2 function mode.
② Digital calibration mode
It is to calibrate into the sensor’s output value. No need to prepare for the actual
load (stand weight). Please refer 8-3 how to calibrate.
③ Actual load calibration mode
It is to calibrate by adding the actual load (standard weight or the load you know).
Please refer 8-4 how to calibrate.

15
 3) DN-25W

For setting mode, there are 2 different types of mode such as Function mode, Actual
load calibration mode.

Measuring mode

While key is being

Press, press key

Function mode
①

END

Actual load
②
calibration mode
END

① Function mode
Acess to each function setup mode. Please refer 8-2 function mode.
② Actual load calibration mode
It is to calibrate by adding the actual load (standard weight or the load you
know). Please refer 8-3 how to calibrate.

16
 8-1. Function mode

1) How to set function.

Measuring Mode State

While key is being

pressed, press key.

END

17
2) How to set RELAY data

① Decision mode (Decision mode : mode 0)

② Limit mode (Low & High limit mode: mode 1 ~ 3)

Measuring Mode

press key

Input

END

18
 3) Function mode table

Function Model DN-10W DN-20W DN-25W DN-30W DN-50W

F-01 Ο Ο Ο Ο(Pulse) Ο

F-02 Ο Ο Ο Ο Ο

F-03 Ο Ο Ο Ο Ο

F-04 Ο Ο Ο Ο Ο

F-05 Ο Ο Ο Ο Ο

F-06 Ο Ο Ο Ο Ο

F-07 Ο Ο Ο Ο Ο

F-08 Ο Ο Ο Ο Ο

F-09 Ο Ο Ο Ο Ο

F-10 Ο Ο Ο Ο Ο

F-11 Ο - Ο - Ο

F-12 Ο - Ο - Ο

F-13 Ο - - - Ο

F-14 Ο Ο Ο Ο Ο

19
 # Function mode list #

Name Function Setting 출고시 기준설정값

F-01 Decimal point 0, 1, 2, 3 1

F-01
(DN- Pulse/circle 0 ~ 360 60
30W)

F-02 Division 1, 2, 5, 10, 20, 50 1

F-03 Display filter 0, 4, 8, 16, 32 16

F-04 Hold mode Sample hold, Peak hold, Absolute peak hold Peak hold

Decision, High limit, Low limit,

F-05 Comparison mode Decision
Low&High limit

F-06 Hysteresis 0 ~ 99 0

F-07 DAC zero -19999 ~ +99999 0

F-07
(DN- DAC mode Display DAC, High speed DAC Display DAC
50W)

F-08 DAC capacity -19999 ~ +99999 10000

F-09 ID Number 0 ~ 32 0

F-10 Baud rate & PRINT 2400, 4800, 9600, 19200, print 9600

F-11 Auto zero tracking 0 ~ 99 0

Auto zero tracking

F-12 0.0 ~ 5.0 sec 0.0
time

F-13 Force unit Kg(kg/㎠), N, ℓb, bar, MPa Kg

F-14 Key Disabling Zero key, Lo key, Hi key, Hold key 0000

20
F-01
1) Decimal point (Decimal point Set-up): DN-10W, DN-20W, DN-25W, DN-50W
(Standard setup value : 1)
Display data
0 00000 : No decimal point
1 0000.0 : One decimal place
2 000.00 : Two decimal places
3 00.000 : Three decimal places

2) Pulse/circle (Set up Purse per circle) : DN-30W

(Standard setup value : 60)
Display data Setting
0 ~ 360 It sets Pulse/1 circle of Rotary body detection sensor
DN30W can set up Pulse number from 1 to 360.

F-02. Division (Minimum display unit setup)

(Standard setup value : 1)
Display data Setting
1 Displayed In 1 (0, 1, 2, 3, 4 …….)
2 Displayed in 2 (0, 2, 4, 6, 8 …….)
5 Displayed in 5 (0, 5, 10, 15 …….)
10 Displayed in 10 (0, 10, 20, 30 …….)
20 Displayed in 20 (0, 20, 40, 60 …….)
50 Displayed in 50 (0, 50, 100, 150 …….)

F-03. Display filter (Display speed setup)

(Standard setup value : 8)
Display data Setting
0 No filter
4 Average time 1/8 sec
8 Average time 1/4 sec
16 Average time 1/2 sec
32 Average time 1 sec

21
F-04. Hold mode
1) DN-10W, DN-20W, DN-25W
(Standard setup value: 1)
Display data Setting
: To hold the display value at the time of Hold
0 Sample Hold
signal input.
: To hold the maximum value of display values
1 Peak Hold (+)
during Hold signal input.
: To hold the maximum absolute value of display
2 Absolute Peak Hold(+/-)
values during Hold signal input.

2) DN-30W
(Standard setup value: 1)
Display data Setting
0 Sample Hold : To hold the display value at the time of Hold
signal input.
1 Peak Hold (+) : To hold the maximum value of display values
during Hold signal input.

3) DN-50W
Display data Setting
0 Display sample Hold : To hold the display value at the time of Hold signal input.
1 Digital sample Hold : To hold the A/D convertion value at the time of Hold
signal input.
2 Diplay Peak Hold : To hold the maximum value of display values during Hold signal
input.
3 Absolute Peak Hold : To hold the maximum absolute value of display values during
Hold signal input.
4 Analog Peak Hold : To hold the maximum value of sensor input during Hold signal
input.

F-05. Comparision mode (Comparision output mode setup

(Standard setup value : 0)
Display data Setting
0 Decision mode : Relay RY1(Lo), RY2(Hi), RY3(Ok) Output
1 High limit mode : Relay RY1, RY2, RY3, RY4 output
2 Low limit mode : Relay RY1, RY2, RY3, RY4 output
3 Low & High limit mode : Relay RY1, RY2, RY3, RY4 output

22
F-06. Hysteresis
(Standard setup value : 00)
Display data Setting
00~99 00 : Hysteresis – not used
01 ~99 : Hysteresis – used (Decision mode is not applied)

F-07. DAC mode

1) DAC zero (Analog output zero set up) : DN-10W, DN-20W, DN-25W
(Standard setup value: 0)
Display data Setting
-19999~+99999 Analog output zero value set-up
2) DAC mode (Analog Output mode setup ) : DN-50W
(Standard setup value : 0)
Display data Setting
0 Display DAC mode Slow, 0
1 High speed DAC mode Fast, 1

F-08. DAC capacity (Analog Outupt value setup)

(Standard setup value : 10000)
Display data Setting
-19999 To setup the rated capacity of analog output
~ <Example of Setup value and output>
+99999 Voltage Outupt Current Output (4
Setup Value
(0~10V) ~20mA)
Display Display
ZERO CAPACITY Output Output
Value Value
-10000 0V -10000 4mA
0 +10000 0 0V 0 4mA
+10000 +10V +10000 20mA
-10000 +10V -10000 20mA
0 -10000 0 0V 0 4mA
+10000 0V +10000 4mA
1

F-09. ID Number (Communication Device Number setup)

(Standard setup value : 00)
Display data Setting
00 : Device number is not set-up (Stream mode : always transmit data )

23
00~32 01 ~32 : Device number is set-up (Command mode : Transmit data by
command)

24
F-10. Baud rate & Print (Communication Speed and print Setup)
1) DN-10W, DN-20W, DN-25W, DN-30W
(Standard setup value: 9.60)
Display data Setting Stream mode Command mode
2.40 2400 bps O O
4.80 4800 bps O O
9.60 9600 bps O O
19.20 19200 bps O X
PRINT PRINT DATA OUT (PT-100) - -

2) DN-50W
(Standard setup value : 9.60)
Display data Setting Stream mode Command mode
2.40 2400 bps O O
4.80 4800 bps O O
9.60 9600 bps O O
19.20 19200 bps O X
38.40 38400 bps O X
57.60 57600 bps O X
PRINT PRINT DATA OUT (PT-100) - -

F-11. Auto zero tracking (Auto zero operation range setup)

(Standard setup value : 00)
Display data Setting
00 00 : Auto Zero is not used.
~
99 01 ~99 : Set up the operation range of auto zero

F-12. Auto zero tracking time (Auto Zero tracking time setup)
(Standard setup value : 0.0)
Display data Setting
00 0.0 : Auto Zero is not used.
~
5.0 0.1 ~5.0 : Set up the auto zero operation time (0.1 ~ 5.0 sec)

25
F-13. Force unit (Conversion Unit setup)
(Standard setup value : 0)
Display data Setting
0 kg.f kg/㎠
1 N kgf × 9.8 - -
2 ℓb kgf × 2.2 - -
3 - - Bar kg/㎠ × 0.98
4 - - MPa kg/㎠ × 0.098
Note) During calibration, set up the unit you want after calibrating it into Kg.

F-14. Key disabling (Front key Locking setup)

(Standard setup value : 0000)
Display data Setting
0 0 0 0 Hold key Lock (1), Release (0)
Hi key Lock (1), Release (0)
Lo key Lock (1), Release (0)
Zero key Lock (1), Release (0)

<Set-up example>
1001 : Zero & Hold key Lock, Hi and Lo key Release

26
 8-2. Digital calibration (Calibration by sensor output value)

1) DN-10W, DN-50W

At the time of purchasing sensor, the rated capacity (R.C) and rated output (R.O)
declared on the calibration sheet can be used for the calibration for easier calibration.

Measuring Mode State

While key is being

pressed, press key.

Displays Function Mode State

Displays Sensor Output Calibration State

Displays Rated Output value Input State

Input the rated output value by using and

key. And then, press key.

Displays the rated capacity value Input State

Input the rated capacity value by using and

key. And then press key.

Calibration Completed.

27
 2) DN-20W

It will be able to calibration with output type and rated capacity setting.

Measuring mode

While key is being

Press, press key

Display Function mode

Display Sensor output value calibration mode

Display output type select mode

Select the sensor output type by using and

key. And then. Press key

: 0 ~ 5V
: 0 ~ 10V
: 4 ~ 20mA

Display R.C. value input mode

Input the rated output value by using and

key. And then. Press key
Calibration end

28
 8-3. Actual load calibration
1) DN-10W, DN-50W
This is a calibration method by adding actual load on the sensor. Standard weight is Needed.

Measuring Mode State

While key is being pressed, press key.

Displays Function Mode State

Displays Sensor Ouput Value Calibration State

Displays Actual Load Calibration State

Displays the Rated output value input state

Input the rated output value by using and key. And then, press
key. (Input 3.0000 if donot know the rated output of sensor)

Displays Zero State

Press key without adding any load on the sensor (Zero Emission)

About 1 second later,

Displays the acual load State

Input the actual load (standard weight) by using and key.

And then press key.

After adding the actual load (standard weight) on the sensor, press key.

After about 1 sec for display,

Displays Shunt CAL Value (Please write to S.CAL)

DATE Rated output S.CAL

Calibration Completed.
29
 2) DN-20W

This is a calibration method by adding actual load on the sensor. Standard weight is needed.
And this can calibrate 1~7 stages, and improve linearity of sensor.

Measuring mode

While key is being Press, press key

Display Function mode

Display Sensor output value calibration mode

Display Actual load calibration mode

Display zero mode. press key without any load on the

sensor

About 1 sec later

Display actual load mode first phase

Input the rated output value by using and key. And

then. Press key

After adding the actual load on the sensor, press key.

About 1 sec later

Calibration end

30
 3) DN-25W

This is a calibration method by adding actual load on the sensor. Standard weight is needed.
And this can calibrate 1~7 stages, and improve linearity of sensor.

Measuring mode

While key is being Press, press key

Display Function mode

Display Sensor output value calibration mode

Display zero mode. press key without any load on the

sensor

About 1 sec later

Display actual load mode first phase

Input the rated output value by using and key. And

then. Press key

After adding the actual load on the sensor, press key.

About 1 sec later

Calibration end

31
 8-4. SPAN constant claibration (Calibratuib by Shunt CAL Value)
1) DN-10W, DN-50W
It is to calibrate with the S.CAL value written down for load calibration. You can
calibrate without any standard weight.
Measuring Mode State

While key is being

pressed, press key.

Displays Function Mode State

Displays Sensor Ouput Value Calibration State

Displays Actual Load Calibration State

Displays Shunt cal value Calibration state

Displays the Rated output value input state

Input the rated output value by using and key. And then, press
key. (Input 3.0000 if donot know the rated output of sensor)

Displays Shunt cal value input State

Input S.CAL value by using and key. And then press key.

Calibration Completed.

32
 8-5 Lock Set-up

You can prevent any accidental operation due to the unnecessary key control by Lock
set-up. After finishing calibration, it is recommended to set the Lock.
At the first stage, please start while the power is OFF.
Related Function when Lock is set : Function related to calibration.

Power is OFF

While key is being pressed,

please turn the power ON.

Please keep pressing key while this is being displayed.

or display

Please select lock or release by pressing key.

ON : Lock is selected, Off : Lock release is selected.

Set-up is completed.

33
9. Product Inspection

Symptom Cause Action Remark

• Load cell is damaged. • Load cell input, output. • Insulation
When Display • Load cell insulation • Check resistance resistance
trembles. resistance. • Check load cell’s (Cable & Case >
• Indirect occurrence insulation resistance. 1000 Mohm)
• Check load cell’s
• Loadcell faulty
When weight insulation resistance.
goes up at a • Check the wiring
regular ratio or between load cell and the
• Loadcell connection is
zero returns are main device.
insufficient.
not made. • Check the load cell’s
calbe’s disconnection.
When weight • Loadcell wiring is • Check load cell’s ouput • Output : (+SIG)
changes into (-). reversed. cable connection. (-SIG)
Displayed as • Load cell is damaged. • Check the load cell’s
“OVER” or • Load cell connection is condition and calbe
“UNDER” bad. connection.

34
10. OPTION

#Option-02 (RS232C)

Since RS232C Interface is very sensitive of electric noise. So please do the wiring
from AC Power and electric wires separately. Also you must use the shield calbe
always.

Indicator Host PC
TX(Transmission Data) RXD(Receive Datea), No.2 Pin
RX(Receive Datea) TXD(Transmission Data), No.3 Pin
GN(Ground) GND(Ground), 5 Pin

1. TYPE : EIA-232C
Method : Half-duplex, asynchronous method.
2. Baud-rate : Select one of 2400, 4800, 9600, 19200, 38400, 57600bps
3. Parity : No Parity
4. Data bit : 8 bit
5. Stop bit : 1bit
6. Stream mode (Ex. Data +1234.5 transmission )

CODE BYTE1 BYTE2 BYTE3 BYTE4 BYTE5 BYTE6 BYTE7 BYTE8

ASCII S T , N T , + 0
HEX 53H 54H 2CH 4EH 54H 2CH 2BH 30H

CODE BYTE9 BYTE10 BYTE11 BYTE12 BYTE13 BYTE14 BYTE15 BYTE16

ASCII 1 2 3 4 . 5 CR LF
HEX 31H 32H 33H 34H 2EH 35H 0DH 0AH

1) BYTE1, BYTE2
. DATA Stable :ST . DATA Unstable :US
. DATA OVERFLOW :OL . DATA UNDERFLOW :UL
35
 2) BYTE3 ~ BYTE6 : fixed character (, N T ,)
3) BYTE7 ~ BYTE14 : DATA 8 BYTE (including +/- )
4) BYTE15 : CARRIAGE RETURN
5) BYTE16 : LINE FEED

7. Command mode : Please setup as RS485 mode and use.( Refer to OP-
03:RS485 )

36
#Option-03 (RS485)

Since RS485 Interface is very sensitive of electric noise. So please do the wiring from
AC Power and electric wires separately. Also you must use the shield calbe always.

1. TYPE : RS485
2. Method : Half-duplex, asynchronous method
3. Baud-rate : Select one of 2400, 4800, 9600bps
4. Parity : No Parity
5. Data bit : 8 bit
6. Stop bit : 1bit

Please set up the device No. referring to INDICATOR Manual.

(Can setup from 1 to 32 channel.)

7. Command Form (PC -> INDICATOR)

CODE BYTE1 BYTE2 BYTE3 BYTE4 BYTE5

ASCII I D 0 1 P
HEX 49H 44H 30H 31H 50H

1) BYTE1, BYTE2 : Fixed Charactor (ID)

2) BYTE3, BYTE4 : Device Number (1 ~ 32)
3) BYTE5 : Command Order (P, H, R, Z)

8. Command Chart

Command
Description
ASCII HEX
Transmit the current value of order
P 50H
equipment.
H 48H Hold for order equipment.
R 52H Release hold for order equipment.
Operate the current value of order
Z 5AH
equipment as ZERO.

37
9. Transmission Data Form (INDICATOR -> PC)

CODE BYTE1 BYTE2 BYTE3 BYTE4 BYTE5 BYTE6 BYTE7 BYTE8

ASCII I D 0 0 1 , + 0
HEX 53H 54H 30H 30H 31H 2CH 2BH 30H

CODE BYTE9 BYTE10 BYTE11 BYTE12 BYTE13 BYTE14 BYTE15 BYTE16

ASCII 1 2 3 4 . 5 CR LF
HEX 31H 32H 33H 34H 2EH 35H 0DH 0AH

1) BYTE1, BYTE2 : Fixed Charactor (ID)

2) BYTE3 ~ BYTE5 : Device number (1 ~ 32)
3) BYTE6 : Fixed Charactor (,)
4) BYTE7~BYTE14 : DATA 8byte (Including +/- )
5) BYTE15 : CARRIAGE RETURN
6) BYTE16 : LINE FEED

38