INSTRUCTION MANUAL FOR
83-488-100 Revision B
MODEL
SERIAL NUMBER
LAMBDA EMI
405 ESSEX ROAD, NEPTUNE, NJ 07753
TEL: (732) 922-9300
FAX: (732) 922-9334
TABLE OF CONTENTS
Description Page
1 GENERAL 1
1.1 INTRODUCTION 1
1.2 SPECIFICATIONS 2
2 INSTALLATION 6
2.1 SAFETY PRECAUTIONS 6
2.2 INITIAL INSPECTION 6
2.3 MOUNTING AND COOLING REQUIREMENTS 6
2.4 ORIENTATION 6
2.5 GROUNDING AND INPUT AC POWER CONNECTION 7
2.6 INTERNAL FUSES 7
2.7 CONNECTING HIGH VOLTAGE OUTPUT 8
2.8 EXTERNAL FILTERING 8
2.9 CLEANING 8
3 OPERATION 9
3.1 ‘L’, ‘S’, & ‘OEM’ MODELS 9
3.2 REAR PANEL 11
3.3 FRONT PANEL CONTROL (‘L’ MODEL ONLY) 12
3.4 FRONT PANEL INDICATORS (‘L’ MODEL ONLY) 13
3.5 FRONT PANEL INDICATORS (‘L’ & ‘S’ MODELS ONLY) 13
3.6 REMOTE CONTROL (‘L’, ‘S’, & ‘OEM’ MODELS) 14
3.7 INITIAL CHECK-OUT PROCEDURE 16
4 APPLICATIONS 17
4.1 DETERMINING CAPACITOR CHARGE TIME 17
4.2 VOLTAGE REVERSAL 17
4.3 PARALLELING UNITS 18
4.4 MEASURING HIGH VOLTAGES 18
4.5 DETERMINING AC LINE CURRENT 19
4.6 OPERATION AS A DC POWER SUPPLY 19
5 MAINTENANCE AND TROUBLESHOOTING 20
5.1 SAFETY PRECAUTIONS 20
5.2 CALIBRATION 20
5.3 MAINTENANCE 20
5.4 INSPECTING THE HV OUTPUT CABLE 20
5.5 TROUBLESHOOTING 21
LIST OF FIGURES
Description Page
Figure 1: XR802 Series Block Diagram 1
Figure 2: Output Power and Current 2
Figure 3: Mechanical Details 5
Figure 4: Input AC Power Connections 7
Figure 5: Model XR802L 9
Figure 6: Model XR802S 10
Figure 7: Model XR802 OEM 10
Figure 8: Rear Panel 11
Figure 9: Model XR802L Front Panel 12
TABLE OF CONTENTS
Description Page
Figure 10: Remote Control Example 15
Figure 11: Current Transformer 17
Figure 12: Peak Measurements During Pulsing 19
1 GENERAL
1.1 INTRODUCTION
The high regulation XR802 Series high voltage power supplies are designed for
charging capacitors in laser systems and other pulsed power applications. The model
XR802DC is a compact high efficiency high voltage DC power supply with the addition
of an externally mounted output filter capacitor. Depending upon the application, the
stored energy requirement of this capacitor can be quite low making the XR802DC an
ideal power supply for applications such as compact high power RF amplifiers for
HDTV applications.
The XR802 Series is available in three different configurations; the XR802L, XR802S
and XR802 OEM. These three different configurations allow the user to choose the
method of controlling the power supply best suited to the overall system requirements.
All three have the same mechanical dimensions, are air cooled and can be mounted in
a standard 19" rack occupying only 8.75" of rack height. The XR802 Series provides
up to 6,000 Watts of average power and can be paralleled for higher total system
power.
The XR802 Series power supply incorporates a high-frequency IGBT Series-resonant
inverter for efficient generation of the output power. A high-performance control
module precisely regulates the output voltage, automatically compensating for line,
load, temperature, rep rate, and program voltage variations. Normal external fault
conditions such as line dropout, open or short circuit load, HV arc and overtemperature
will not damage the unit.
AC FRONT END HV OUTPUT HV
INPUT HIGH FREQ.
POWER FUSES FILTER SECTION OUTPUT
INRUSH LIMIT INVERTER STEP-UP XFMR
RECTIFIER RECTIFIER
AUX POWER FILTER
HV DIVIDER
CONTROL
BOARD
CONTROL
Figure 1: XR802 Series Block Diagram
Page 1 of 21
83-488-100 Rev. B
The output voltage of the XR802 power supply is fully adjustable over each range.
100
% USABLE 75
OUTPUT
POWER 50
25
25 50 75 100
% OUTPUT VOLTAGE
Figure 2: Output Power
1.2 SPECIFICATIONS
OUTPUT VOLTAGE/CURRENT
The output voltage is fully adjustable over each range. Recommended control range
for full regulation is 10% to 100% of Full Scale. The output current from 100% to 10%
of rated voltage is constant. This provides the full 6000 Watts of average output power
at 100% of rated voltage.
Voltage Range Max Current Max Current
Cap-Charging DC
0-1 kV 14.0 A 8.0 A
0-2 kV 7.0 A 4.0 A
0-4 kV 3.5 A 2.0 A
0-5 kV 2.8 A 1.6 A
0-10 kV 1.4 A 800 mA
0-20 kV 700 mA 400 mA
0-30 kV 467 mA 260 mA
0-40 kV 350 mA 200 mA
0-50 kV 280 mA 160 mA
CHARGE RATE: DC POWER OUTPUT:
6000 J/sec average 8,000 watt
REGULATION:
±0.1% to 250 Hz Standard
±0.3% to 1 kHz Standard ±0.1% to 1 kHz Available
Total pulse-to-pulse variation with no series terminating resistance/inductance.
STABILITY
<0.2% per hour after 1 hour warm up.
PROGRAMMING LINEARITY
+/-1.0% of full-scale @10% to 100% of rated output.
Page 2 of 21
83-488-100 Rev. B
PROGRAMMING ACCURACY
+/-1.0% of full-scale @10% to 100% of rated output.
INTERNAL STORED ENERGY
0.5 Joules Max.
EFFICIENCY:
85% minimum at full load and nominal line.
A.C. POWER INPUT CONNECTIONS
5 positions VDE/IEC Approved Terminal Block
Ø1, Ø2, Ø3, N, for 400 VAC input voltage
Ø1, Ø2, Ø3, for 209 VAC input voltage
INPUT VOLTAGE/CURRENT
208V Configuration: 180-264 V, 3 Phase, 50/60 Hz, 45 A max
400V Configuration: 360-440 V, 3 Phase, 50/60 Hz, 25 A max
POWER FACTOR:
Passive PFC. 85% minimum at full power and nominal line input
INRUSH CURRENT
Limited to below full power current.
PROTECTION FEATURES
Output short circuit and HV arc-to-ground any time during operation.
Open circuit at turn-on, will not damage power supply.
Remote HV Safety Interlock loop
AC input power contactor (Standard on ‘L’, ‘S’; Optional for ‘OEM’)
Shutdown on over-temperature, overvoltage, and open interlock.
Highly buffered I/O for noise immunity in severe electrical environments.
COOLING
Forced air with internal fan, -20°C to 40°C inlet temperature,
ENVIRONMENTAL CONDITIONS
The power supply is safe under the following conditions:
Altitude up to 3000m (9900 ft) operating, nonoperating 12121m (40000 ft)
Temperature 5°C to 40°C
Storage temperature - 40°C to 85°C.
Maximum relative humidity 80% for temperatures up to 31°C decreasing linearly to
50% relative humidity at 40°C.
Fluctuations not to exceed the stated input voltage range.
Transient overvoltages according to Installation Categories (Overvoltage
Categories) I, II and III in accordance with IEC 1010, current revision.
Operation only in horizontal position for w/Oil Insulated HV Output.
Page 3 of 21
83-488-100 Rev. B
HV OUTPUT CONNECTOR AND CABLE
Output Voltage Connector Cable
<= 6.0 kV Amphenol ‘HN’ RG-8/U
> 6.0 kV Proprietary Dielectric Sciences 2214 80kV
10'coaxial hv cable with grounded shield standard. Other lengths available.
METERING ACCURACY
All ±2%
FRONT PANEL
“L” Model
3 ½ digit voltage & current meters.
10 segment voltage and current trend bar graphs.
Multi-turn HV output level control.
HV ON, HV OFF, and push to view push button.
3 position key switch removable in Off position.
“L & S” MODELS
HV ON Indicators
HV OFF Indicators
INHIBIT Indicators
END OF CHARGE Indicators
LOAD FAULT Indicators
OVER TEMPERATURE Indicators
SHOCK
25 Gpk, half Sine wave 11mSec, x, y, z axis (3 total)
VIBRATION
MIL-STD-810E Method 514.4 basic transportation
Common carrier 10-500Hz, 0.015 g2/Hz
Duration 1 Hour
SIZE
Standard 19" rack mount. 8.75" high, 17" deep. Refer to Figure 1 for details.
WEIGHT
80 Lbs., 36 kg w/Oil Insulated HV Output
60 Lbs., 27 kg w/Air Insulated HV Output (≤6kV)options:
ALL MODELS:
Custom output voltages
0 - 5 VDC Programming
±0.1% regulation to 1kHz.
Remote output voltage sensing
Rack mount slides
EMI filter
Page 4 of 21
83-488-100 Rev. B
High rep rate unshielded HV connector with silicon HV cable
Custom length HV cable.
XR802 OEM:
Front panel circuit breaker
Internal AC contactor.
Figure 3: Mechanical Details
# " $ %
($
0 ("/ / 1
)(*(+(
,-,.+/ ,
%(
0 (//1
&# '
("
0 "(%/ / 1
("
0 //1
($"
0 %( / / 1
"($
0 "( / / 1
%(
0 (//1
($"
0#$ ($/ / 1
$(
0# (//1
Page 5 of 21
83-488-100 Rev. B
2 INSTALLATION
2.1 SAFETY PRECAUTIONS
The user should be aware that if the equipment is used in a manner not specified by
the manufacturer, the protection provided by the equipment may be impaired.
All model XR802 power supplies contain hazardous voltage and energy. The power
supply must only be operated by qualified personnel who have read this operator' s
manual and are familiar with the operation, hazards and application of the power
supply. Proper care and judgment must always be observed. Ensure all covers are in
place and securely fastened and the required grounding and cooling is supplied before
connecting input AC power. Proper grounding from the input AC power is required to
reduce the risk of electric shock. Use extreme caution when connecting input AC
power and never apply the incorrect input power. Use extreme caution when
connecting the high voltage output cable. Ensure all load capacitors are completely
discharged prior to connection and never handle the output cable when the power
supply is operating. Always replace fuses with the same type and Volt/Amp ratings.
Never attempt to operate the power supply in any manner not described in this
manual. Never remove DANGER or WARNING labels from the power supply, and
replace lost or damaged labels immediately. The power supply should only be serviced
by EMI factory qualified personnel.
2.2 INITIAL INSPECTION
The shipping container should contain the following items: power supply, HV output
cable, male 25-pin "D" remote control connector, test data sheet and operator' s
manual. Examine the items immediately for damage. Locate the serial number label on
the side of the power supply and verify the model number, the input voltage rating and
the output voltage rating and polarity. In the event of any damage promptly notify the
transportation company and EMI customer service.
2.3 MOUNTING AND COOLING REQUIREMENTS
The power supply should be mounted in a standard 19" EIA enclosure or equivalent.
Chassis support brackets or rails must be added to the bottom of the power supply for
proper weight distribution. In all cases adequate clearances must be provided for
proper air flow and cable bends. Generally, at least 4" of clearance should be allowed
at the rear of the power supply and 1" at the sides.
When operating in an enclosed system, care must be taken to ensure the ambient inlet
air to the power supply does not exceed the maximum operating temperature of 40°C.
this often requires addition of a system heat exchanger.
2.4 ORIENTATION
Power supplies with air H.V. sections (output voltage 6kVcan be operated in
any orientation/position. Oil Insulated power supplies must be operated in a
Page 6 of 21
83-488-100 Rev. B
level position. More than a quarter of an inch (5.1mm) difference in height in any
direction could cause an arcing condition in the high voltage tank.
2.5 GROUNDING AND INPUT AC POWER CONNECTION
Proper grounding from the input AC power is required to reduce the risk of electric
shock. The metal chassis of the power supply is grounded through the green/yellow
earthing wire at the input AC power terminal block. Use extreme caution when
connecting input AC power and never apply the incorrect input power. Connect the
three lines of the input power to the L1, L2, L3 terminals and the earth ground to the
terminal marked with the ground symbol. No neutral connection is required for the
200V (180-264VAC) configuration If the power supply was purchased with the 400V
(340-460VAC) configuration, connect the neutral wire to terminal marked N. The power
supply cannot be operated from a single phase line. Refer to Section 4 "Applications",
to calculate line currents for various operating conditions such as reduced power or
charging very large capacitor banks.
For input power connection use wire with min 8 AWG [0.129” (3.264 mm) diameter]
and 600V insulation. External switch or circuit breaker (rating 40A/phase for 208VAC,
30A/phase for 400VAC) has to be provided. Circuit breaker must be all pole mains
disconnect. The location of the circuit breaker or switch must be as close to the supply
as practically possible (within reach of the operator).
L1 L2 L3 N
Figure 4: Input AC Power Connections
2.6 INTERNAL FUSES
All internal fuses must be replaced by a fuse of proper rating and type. All the fuses
are listed in the following table.
Reference Designation Location
60A, FAST, 300V for 208VAC, Class T
F1, F2, F3
30A, FAST, 600V for 400VAC ,Class T
VNR Board
F4, F5 2.5A, SLOW, 250V (5mm x 20mm)
F6, F7 3.15A, SLOW, 250V (5mm x 20mm)
F1 Aux Board PTC Fuse, 2.5A, 50V
F1 Control Board 250mA, SLOW, 250V, 5mm x 20mm
Page 7 of 21
83-488-100 Rev. B
2.7 CONNECTING HIGH VOLTAGE OUTPUT
Ensure that the power supply is off and disconnected from the input power and
that all load capacitors are discharged and shorted to ground before making any
connections. Never handle the HV cable during operation.
Always use the HV connector and cable provided with the power supply or an
equivalent substitute provided by ALE Systems. Fully insert the connector end of
the HV cable and tighten the locking nut only "hand tight".
When operating above 20kV and 200 Hz rep rate it is recommended that a silicone
grease (such as Dow Corning DC-4) be used on the HV cable before insertion into the
HV connector. This displaces the air in the connector and reduces long term corona
effects.
The HV cable shield is connected to the power supply chassis and should be used as
the HV return. An additional grounding stud is provided adjacent to the HV connector
and should also be connected to the HV return. The standard shielded HV cable can
contact earth ground without consequence. The optional unshielded silicone HV cable
can also contact ground, but isolating it will minimize the effects of corona in the
system.
Keep the minimum HV cable bend radius greater than 4" to minimize stress on the
insulation. Keep the HV cable as distant as possible from the input power and the input
control signals.
Some peak current will flow out of the power supply during discharge and return
through the HV return and system chassis. This current comes from voltage reversal in
underdamped systems and from normal discharge of filter and cable capacitance. The
path for this current should not parallel control signal returns since the resulting
voltages could interfere with normal system operation. When due to voltage reversal at
high rep rates, this current could damage the power supply. Generally a resistor in
series with the HV output can be added to limit this current to an acceptable level.
Refer to Section 4 "Applications" for more information.
2.8 EXTERNAL FILTERING
An external line filter is required to insure compliance with EN55011 emission
standards. A line filter is available from Electronic Measurements, Inc. for the
customer’s integration into his system.
This filter must be installed in the customer’s cabinet in such a manner as to minimize
RF coupling from the HV DC output onto the AC mains. Due to the variations in the
final application, it is the customer’s responsibility to insure the completed system
complies with any applicable EMC standards.
2.9 CLEANING
Generally, no cleaning is required. If excessive dust is collected it can be wiped off
with a damp rag. All voltage to the supply must be disconnected and the output
discharged before attempting to clean the unit.
Page 8 of 21
83-488-100 Rev. B
3 OPERATION
3.1 ‘L’, ‘S’, & ‘OEM’ MODEL
MODEL XR802
This model has full front panel instrumentation for use in laboratory, prototype or OEM
systems. The XR802L can be operated either from the front panel or from the rear
panel remote control connector. The front panel includes power on/off, remote/local
and HV on/off switches, output voltage adjust, view set switch, digital voltage and
current meters, quick reference bar graphs and status indicators. An internal AC
contactor is included which is controlled by the front panel power switch. A BNC
connector is provided on the rear panel for easily connecting a pulsed INHIBIT signal.
The model XR802L can be operated as a “master” unit in parallel with several model
XR802S “slave” units for increased output power. Refer to Section 4 “Paralleling
Units”.
Figure 5: Model XR802L
Page 9 of 21
83-488-100 Rev. B
MODEL XR802S
This model has only a power switch and status indicators on the front panel. It must be
operated through its remote control connector and can function as a standalone unit or
in parallel with other units. Several model XR802S units can be paralleled as "slaves"
controlled by either a "master" XR802L or a single remote control circuit. An internal
AC contactor is included which is controlled by the front panel power switch.
Figure 6: Model XR802S
MODEL XR802 OEM
This model has a blank front panel and is operated the same as an XR802S, from the
remote control connector only. It can function as a standalone unit or in parallel for
increased output power. The basic model XR802 OEM is supplied by externally
controlled AC power. It can also be configured with either an internal AC contactor or
front panel circuit breaker option.
Figure 7: Model XR802 OEM
Page 10 of 21
83-488-100 Rev. B
3.2 REAR PANEL
Figure 8 shows the rear panel of the model XR802L. The DB-25 Female REMOTE
connector is used to control the power supply when the CONTROL KEY SWITCH on
the front panel is in the REMOTE position.
The INTERLOCK terminal block (at 24 VAC) can be connected to system interlocks to
disable the power supply when opened. Jumpering the two terminals together allows
the power supply to operate. The external interlock switch contacts must have a
minimum of current rating of 250 mA. No other electrical connections should be made
to these terminals. The interlock terminals should not be connected to ground. Ground
connection will disable power supply.
The INHIBIT connector allows for easily connecting a pulsed INHIBIT signal when
operating from the front panel. The INHIBIT signal in the REMOTE connector can be
used when operating in remote control mode.
The SLAVE connector is used to control model XR802S/XR802 OEM power supplies
operating in parallel with an XR802L "master" unit. The model XR802S and model
XR802 OEM do not have the INHIBIT and SLAVE connectors.
Rear Panel Connectors
Connector Type Function Notes
HV Output Proprietary >6kV Coaxial HV output Ground referred
Amphenol ‘HN’ <6kV
REMOTE DB-25 FEMALE Power supply control input ‘L’, ‘S’, & ‘OEM’
from user
SLAVE DB-25 MALE Power supply control ‘L’ version ONLY
output from master
INHIBIT BNC Female High speed HV inhibit 0-40uS Response
SENSE BNC Female Remote Sense Input ‘RS’ Option Only
INTERLOCK 2 Position Terminal Block Safety Interlock Requires isolated
Opens AC contactor switch. 500mA AC
L1 L2 L3
Figure 8: Rear Panel
Page 11 of 21
83-488-100 Rev. B
3.3 FRONT PANEL CONTROL (‘L’ model only)
POWER SWITCH:
Connects AC input power to the control circuitry and closes the internal AC contactor if
the interlock is closed.
CONTROL SWITCH:
Directs the power supply to take on/off and voltage program commands from either the
front panel (LOCAL position) or the remote control connector (REMOTE position). The
OFF position disables the power supply regardless of other commands.
HV ON SWITCH:
Turns on the high voltage output to the level set by the HV adjust knob. Also used with
HV OFF to reset latched fault conditions: overvoltage, open circuit, over-temp, AC
under-voltage, and interlock open. Resets latched faults.
HV OFF SWITCH:
Turns off the high voltage output. HV OFF is used to reset the latching fault conditions.
VOLTAGE ADJUST:
Clockwise increases the output from zero to maximum, 10 turns full scale.
VIEW SET:
Previews the voltage and current adjust set point before HV ON.
Figure 9: Model XR802L Front Panel
Page 12 of 21
83-488-100 Rev. B
3.4 FRONT PANEL INDICATORS (‘L’ model only)
VOLTAGE METER
Displays the PEAK output voltage in kV. When ‘VIEW SET’ is depressed the display
will indicate the set point voltage.
VOLTAGE BAR-GRAPH
Displays the REAL-TIME output voltage as a percent of rating. When ‘VIEW SET’ is
depressed the display will indicate the set point voltage.
CURRENT METER
Displays the REAL-TIME output current in Amperes. When ‘VIEW SET’ is depressed
the display will indicate the maximum current.
CURRENT BAR-GRAPH
Displays the REAL-TIME output current as a percent of rating. When ‘VIEW SET’ is
depressed the display will indicate the set point voltage.
3.5 FRONT PANEL INDICATORS (‘L’ & ‘S’ models only)
HV ON
Lights to indicate that the high voltage output is enabled. If a fault condition occurs the
light will extinguish regardless of the state of the HV ENABLE.
HV OFF
Lights to indicate that the high voltage output is not enabled. If a fault condition occurs
the light will blink at about a ½ Second rate.
INHIBIT
Lights to indicate the active state of the externally applied or internally generated inhibit
signals. In capacitor charging applications this light will blink during each discharge
cycle.
END OF CHARGE
Lights to indicate that the measured output voltage is equal to the programmed set
point voltage.
INTERLOCK OPEN
Lights to indicate an open interlock loop.
LOAD FAULT
Lights to indicate any failure with the high voltage output. Among the failures are
overvoltage, output overload, inverter overload, etc.. Some possible causes are:
HV diodes shorted, O/P shorted to gnd, etc. Load fault may be activated if a very large
cap is being charged.
OVERTEMP
Lights to indicate that the inverter heatsink is running too hot. The major causes for
this would be exceeding the rated average power, a high ambient temperature, or
locked fan.
Page 13 of 21
83-488-100 Rev. B
3.6 REMOTE CONTROL (‘L’, ‘S’, & ‘OEM’ models)
All three models are easily controlled through their remote connector on the rear of the
unit. Only the HV ENABLE (Pin 8), V PROGRAM (Pin 22) and GND (Pins 12 & 24)
signals are required for operation. The remaining signals are provided for status
monitoring and fault diagnosis. A schematic diagram showing the suggested interface
circuit appears after the following description of control signals.
DB-25 Cable
Pin Wire Direction Type Description
No No
1 1 OUTPUT ANALOG REAL-TIME OUTPUT VOLTAGE
2 3 INPUT ANALOG CURRENT PROGRAMMING
3 5 OUTPUT OPEN-COL INHIBIT INDICATOR
4 7 OUTPUT OPEN-COL VOLTAGE REGULATION MODE
5 9 OUTPUT OPEN-COL END OF CHARGE
6 11 BI-DIREC DIGITAL OVERLOAD SYNCHRONIZATION
7 13 INPUT DIGITAL INHIBIT INPUT - ACTIVE HIGH
8 15 INPUT DIGITAL HV ENABLE
9 17 OUTPUT ANALOG PEAK OUTPUT VOLTAGE
10 19 OUTPUT OPEN-COL HV ON INDICATOR
11 21 BI-DIREC ANALOG CURRENT SHARING
12 23 GROUND ANALOG COMMON
13 25 OUTPUT ANALOG REAL-TIME OUTPUT CURRENT
14 2 OUTPUT POWER +15VDC 250mA (Fused)
15 4 OUTPUT OPEN-COL CURRENT REGULATION MODE
16 6 OUTPUT OPEN-COL OVER-TEMPERATURE FAULT
17 8 OUTPUT OPEN-COL INTERLOCK FAULT
18 10 OUTPUT OPEN-COL OVERLOAD FAULT
19 12 OUTPUT OPEN-COL LOAD FAULT
20 14 INPUT DIGITAL /INHIBIT INPUT - ACTIVE LOW
21 16 BI-DIREC DIGITAL OSCILLATOR SYNCHRONIZATION
22 18 INPUT ANALOG VOLTAGE PROGRAMMING
23 20 OUTPUT OPEN-COL HV OFF INDICATOR
24 22 GROUND DIGITAL & POWER RETURN
25 24 OUTPUT POWER +12V 100mA (Unfused)
REMOTE Connector Pin-Out
Page 14 of 21
83-488-100 Rev. B
Figure 10: Remote Control Example
Page 15 of 21
83-488-100 Rev. B
3.7 INITIAL CHECK-OUT PROCEDURE
The power supply should have no visible damage or defects and the cover should be
securely fastened. Properly connect the input power, control connector and HV output.
If there is no load connected, the power supply will sense an open circuit and
immediately shut down indicating a LOAD FAULT. If there is a short circuit or overload
condition on the output, the power supply will operate in a 50% duty cycle protection
mode and indicate a LOAD FAULT. An overload condition can occur if the INHIBIT
signal is missing and the discharge rep rate is too high to allow the capacitor to fully
charge to V PROGRAM. Double check all connections and ensure that all personnel
are protected from the HV output. With the HV adjust at zero volts, turn the power
supply on in the following sequence:
XR802L FRONT PANEL CONTROL:
Turn HV ADJUST knob fully counterclockwise.
Turn POWER switch to ON.
Turn CONTROL key switch to LOCAL.
Push HV ON switch.
Verify the HV output is at approx. zero volts.
Increase HV output slowly and verify adjustability.
XR802L REMOTE CONTROL:
V PROGRAM signal (pin 22) at zero volts.
ON/OFF signal (pin 8) at zero volts.
Turn POWER switch to ON.
Turn CONTROL key switch to REMOTE position.
Assert ON/OFF signal to 15V.
Verify HV output is at approx. zero volts.
Increase HV output slowly and verify adjustability.
XR802S REMOTE CONTROL:
V PROGRAM signal (pin 22) at zero volts.
ON/OFF signal (pin 8) at zero volts.
Turn POWER switch to ON.
Assert ON/OFF signal to 15V.
Verify HV output is at approx. zero volts.
Increase HV output slowly and verify adjustability.
XR802 OEM REMOTE CONTROL:
V PROGRAM signal (pin 22) at zero volts.
ON/OFF signal (pin 8) at zero volts.
Assert ON/OFF signal to 15V.
Verify HV output is at approx. zero volts.
Increase HV output slowly and verify adjustability.
Page 16 of 21
83-488-100 Rev. B
