TABLE OF CONTENT DESCRIPTION RTU50 HARDWARE OVERVIEW ¢ RTU C50 MASTER PROCESSOR MODULE, RTU C50 POWER SUPPLY MODULES ¢ RTUCS0 DUAL COMMUNICATION MODULE © RTU C50 OPTONET MODULE © RTU C50 INPUT/OUTPUT MODULE RTUS50 SOFTWARE OVERVIEW ¢ RTU C30 CONFIGURATION USER MANUAL © RTU C50 FIRMWARE WISP+ PROTOCOL USER DOCUMENT © RTU C50 IEC 60870-5-101 SLAVE USER MANUAL SECTIONSECTION A-1 RTU C50 MASTER PROCESSOR MODULEFOXBORO a PSS 21H-8C1 B4 VA Series® Remote Terminal Unit (RTU) RTU 50 Pll and PIIE Master Processor Modules ‘The RTU 50 Pll and PIIE Master Processor Modules are the heart of the ATU 50, delivering features such as user-dofined calculations and database; system ‘maintenance and diagnostics; real-time operating system for deterministic monitoring and control; industry standard processor. The PIE Master Processor Module also features a 10BaseFL duat Ethemet intoriace for local (LAN) and wide (WAN) area network applications, ‘The RTU 50 Pll and PIIE use standard Industry architecture, incorporating a 92-bit processor and FLASH technology to deliver powerful and flexible inteligencs to the RTU 50 "An Invensys company FEATURES: Key features are: ‘AMD 22-bit microprocessor Altera programmable chipset 4.MB FLASH 16 MB RAM Diagnostic LEDs 128 K Protecied Mode BIOS. Foxboro Electrobus interface IEEE P996 bus interface ‘1 ms time base ‘or Sequence of Events (SOE) time tagging Watchdog timer ‘Two RS-282-C serial ports Real-time calendar clock - 5 ppm Non-volatile parameter memory. Product SpecificationsPSS 21H-8C1 BA Page 2 Optional Features ‘Avaliable optional features are: + 64 MHz, AMAB6DX¢, 32-bit microprocessor + Upto 128 MB RAM (EDO SIMM) + Upto 10MB FLASH + Dual 10BaseFL Ethernet Interface, ‘OVERVIEW ‘The RTU 50 Pll end PIIE modules utlize standard PC aichitecture to deliver powerful and scalable processing capability to the ATU 50. Foaturing a 82-bit processor and FLASH memory, the ATU 50 Pll and PIIE Masior Processor Modules control all RTU logic and diagnostics, and provides support for optional periphorals and 10BaseFL Ethemet ‘communication interface. ‘The module features dlagnostic LEDS for rapid feut diagnosis and an intogral serial port for connection of dlagnostio and configuration tools. A second serial portis also available for interfacing to inteligent electronic devices. This port is user programmable, allowing the implementation of proprietary and industry standard protocols (such as Modbus). ‘The RTU 50 Pll and PIIE reside alongside the power ‘supply inthe first slot of the RTU 80 main fl. FUNCTIONAL DESCRIPTION ‘The ATU 50 Pll and PIIE provide PC 1/0 servioss, memory Integrity checks, and interrupt checks to guarantee the reliable and deterministic operation of all RTU processes and logic. The powerful standard processor comes complete with 16 MB of RAM, 16 KB of cache memory, maths co-processor, 128 KB of EPROM and 2 MB of FLASH FLASH A key feature of tho RTU 50 Pil and PIIE is the use of FLASH for the storage of the AMX® Real-Time Operating systam, ATU system software, ATU database configurations and user configurable calculations. The system is flexible, allowing the user to pre-program the necessary software and database requirements within an office environment or on site. ‘The new FLASH card is then simply installed into a pre-commissioned ATU. This ‘exibility permits easy Upgrades of ATU sofiware aid Ualabasy changus. ‘The software package also provides diagnostic functions for system maintenance, which operates in conjunction with a personal computer to provide aceass to /O logic, communications and controls. DUAL 10BASEFL ETHERNET BOARD ‘The ATU 50 PIIE features a dual 10BaseFL Ethemet board that provides a cost-effective and versatile fiber optic Ethernet interface for the UA Serios RTU 50. ‘The optical interface maintains the high electrical Isolation characteristics of the RTU 60. ‘The dual communications channels function as primary and backup paths, delivering fault-tolerant ‘communications for critical processes. ‘The rapid deployment of the Ethernet as a network Infrastructure means that you can take advantage of the VA Series RTU 50 to interface to a wide varioty of Intelligent field devices, and LAN/WAN connections to maximize your SCADA investment,PSS 21H-8C1 B4 Page 3 FRONT PANEL LAYOUT ‘The ATU 50 Pil and PIIE front panels feature diagnostics and interfaces to facilitate maintenance, ‘configuration, and communications. A Sense/Reset (SEN/AST) switch allows the module to be hardware reset or to enter low level diagnostics mode. The FLASH memory card socket allows for the changing of the FLASH card. Two serial ports are also provided, with one serving as a configuration diagnostics port and the other as serial interface. Eight dlagnosticierror LEDs are provided to indicate the status of diagnostic points and a RUN/FAIL LED indicates module operation status. On the PIIE, the dual 10BaseFL Ethernet board provides additional LED indication for each fiber optic ‘Channel (light level, transmit, receive, jabber, collision) POWER SUPPLY MODULE , 1 ouTPur MopuLes—, Pll Front Panel and PIIE Front Panel i [ a BR [——— eur mooutes ——— e iS S Eerereree fa | dasren rcesson woos pun cowsamocione ttsPSS 21H-8C1 B4 Page 4 PHYSICAL SPECIFICATION Physical Size Double Eurocard format 160 x 283.4 mm bare board 4182 x 261.8 x 30 mm including connectors and handle ENVIRONMENTAL SPECIFICATIONS Ambient Temperature (0°C to 60°C (optional -20°C to 70°C) Humidity 10% to 95% RH (noncondensing) FUNCTIONAL SPECIFICATIONS Power Requirements 45 Vat 1.5 Amaximum, 1.0 Atypical +15 V at 100 mA maximum, 15 mA typical “15 at 200 mA maximum, 30 mA typical Optional solection of +12 V and-12 V Microprocessor 32-bit AM4B6DX4, 64 MHZ Operating System AMX Bios Foxboro protected made Memory Modules + 128 KB FLASH (28F010) +16 MB DRAM (EDO SIMI) + 4MB FLASH card expandable to 64 MB. + 32KB nonvolatile RAM Poripheral Controllers TL16C554 Quad UART Custom chipset using Altera EPLD Bus Specifications Foxboro Electrobus IEEE P996 Industrial PC/AT Bus Watchdog Timer 1 second timeout to reset the RTU Front Panel RUNIFAIL LED Eight diagnostic/etror LEDS COM and COM? serial ports Sense/Reset switch FLASH memory card socket (PCMCIA) Serial Ports COMI - configurationidiagnostios CON2 - GPS/IED/user serial interface Electrical VF -DB9 male IBM PC compatible (DTE) Real-Time Clock IBM PCIAT compatible, Y2K compliant, with § ppm accuracy, also generates Electrobus synchronizing and SOE clocks Backup Time Real-time clock and non-volatile RAM are maintained during power outage, via an on-board capacitor or an optional lithium battery; up to 24 hours backup with ‘capacitor, or 8 years with the optional lithium batteryPSS 21H-8C1 B4 Page 5 PIE DUAL ETHERNET BOARD Ports ‘Two 10 Mbps 10BaseFL Ethemet ports, Interface ‘Two ST connectors (TX, RX) per port TRANSMIT POWER -15 dBm + 8 dB (-2 dB end of life) RECEIVE LEVEL “12 dBm to -$2.5 dBm for bil wior rate (BER) of 109 RANGE 2000 m WAVE LENGTH 820m OPTICAL CABLE ‘Multimade glass fiber 62.5/125 um Indicators 5 LEDe per port indicating link status (light level, transmit, receive, jabber, colision) Ethernet Chips ‘Two AM79C960 - PCnet-1SA Single Chip Ethernet Controllers ‘Sharod Momory ‘32 KB RAM avallable per port Physical Layer HFBR-1414 Transmitter HFBR-2416 Receiver HFBR-4663 10BasoFL Transceiver ORDERING INFORMATION Part Number s¥-0399066, s¥-0399067 Description ATU 50 Pll Master Processor Module ATU 50 PIIE Master Processor Module with Dual 10BaseFL EthernetPSS 21H-8C1 B4 Page 6PSS 211-801 B4 Page 7PSS 21H-8C1 B4 Page 8 “The Foxboro Company 3 Commerc! Street Focbore, Massocrusets 02035-2008 Unies Sates of Amerie higivamfoxbora.com Inside US. 1-506-543-8750 or 1-885-FOKBORO (1-888-960-2678) Ouiside US: Caniat your local Foxboro representative Foxboro and UA Series are registered vademarks of The Foxboro Company. Inveneys is a vadorark of Iensys pe. AM fa adomark of Kadak Prucs, Ld. PCIAT fea trademar of IBM Corporation Modbus is a tadamark of AEG Scinelder Automation, Ine. CCopyeght 1987-2000 The Foxboro Company ‘A rights reserved a.o21 Printed in USA An invensys company s00SECTION A-2 RTU C50 POWER SUPPLY MODULEProduct Specifications PSS 21H-8A8 B4 V/A Series® Remote Terminal Unit (RTU) _ RTU50 Power Supply Module INTRODUCTION Each W/A Seriss RTUSO catd file has a removable Power Supply Module sized to support a fully populated file. ‘The Power Supply Module is located in the frst slot of each RTUSO file, This slot may be shared with the Master Processor Module and/or a Communications. Module or OptoNet Module. The RTUSO Power Supply Module operates over a vide input voltage 18 to 164 V de, negative or positive earth, to accommodate the vast majority of site battery backed supplies. ‘This module replaces the 24, 48 or 129 V de nominal power supplies (Part Numbers S¥-0702041, SY-0702042, and SY-0702054) FEATURES * Wide range inout supply: 18 to 164 V de positive cor negative earthed + 100 W output capacity * Supports a fully populated RTU 50 file with 50% of 10 A relays operated simultaneously + High conversion efficionay + Withstands 4 ms dead shorted supply input + Built-in over-current and over/under voltage protection + RTU systom failure alarm LED and contact + Control supply isolation input * Loop power distribution terminals, ‘+ Power supply OK and Fail LEDs FUNCTIONAL DESCRIPTION ‘The Wide Range 100 W Power Supply module provides the regulated +5 V de, +15 V de, and =15 V de operating supplies for an RTUSO file. A 41,000 V de supply is provided as an internal reference {for automatic callbration of analog input modules. “The module's switched mode design provides operation over a wide de input range from 18 to 164 V, provides high input to output isolation, controls switch-on inrush current, and minimizes size-to- ‘weight ratio, while offering high power conversion. efficiency and high reliability Internal monitoring provides a system reset to the TU 50 modules should the +5 V supply be abnormal. A front panel INPUT OK LED i supply Is normal. Monitoring of the 15 V rails Is indicated by 18 V OK LED on the front panel ‘Avelay contact (normal open and normal closed) controlled by the system fail and +15 V rail faut, is avaliable on the front panel terminals, icates the Invensys”PSS 21H-8A8 B4 Page 2 Module Description Each V/A Series RTUSO card file has a removable Power Supply Module (see Figure 2), Because each card fla has a dedicated power supply sized to accommodate a fully equipped file, future expansion within a file does not require any power supply changes, while distributed power supplies enhance availabilty. Rogardiess of the VO in an RTU, the power supply is always correctly sized. ELECTROBUS INTERFACE WONTORS AND inoigarons "ANALOG INPUT Powen SYSFAL GHeck voLTAge SUPP RELAY DAIWER deinpuT : 1) 4 I I SURGE ouput SUPPRESSION RELAY AND LED i AND FILER INDICATOR, I I INPUT ‘ari TERMINAL "NS TERMANALS FUSE POWER SUPPLY MODULE Figure 1. A Series RTUSO Power Supply Module Functional Block Diagram [— ourput mopues —,——— INPUT MopuLES ———— i Py = iS Ho SEEHR = E ai Is Tprororss Poamnone Y evvers I ramet i MASTER PROCESSOR MODULE UAL COMMUNICATIONS MODULE Figure 2. VA Series RTUSO Power Supply System, Example ImplementationPSS 21H-8A8 B4 Page 8 Front Panel ‘The I/A Series RTUSO Power Supply Module is always located in the first sict of each file and may be shared with the Master Processor Module andlor a communications module (see Figure 3). ‘The module plugs into a backplane (Electrobus) via a DIN 41612 connector and is double Eurocard size. Front panel cutout allows a Dual Communication Module or OptoNet Module to be fitted to Slot 1 of the file (see Figure 2). eo ‘The Power Supply Modules can be suppllad using & 24,48, or 129 V de power source, ‘The Power Supply Module provides contacts for an external waming lamp or audible alarm to indicate an TU or 15 V fault Provision is also made for control supply isolation by affixing an external switch of ele. ‘A pair of terminals provides connection of a remote facility to isolate supply to control outputs ‘Atront panel power switch is provided. Figure 3. Front Panel PHYSICAL SPECIFICATIONS Physical Size ‘The module requires frame space of 40 mm 190 x 262 x 40 mm assembly ENVIRONMENTAL SPECIFICATIONS Ambient Temperature A0SC to +70°C Humidity 10% to 95% (noncandensing) Cooling Natural convection, no forced cooling requiredPSS 21H-8A8 B4 Page 4 FUNCTIONAL SPECIFICATIONS. Power Requirements 4130 W maximum input Input Voltage Wide range input voltage 18 to 164 V de Suitable for use on 24 V de, 48 V de, and 128 V de nominal source supplies Output Capability 45 Val 108 HB5VatgA 15 Val 0.45 A Maximum output of 100 watts total permitted Input Current 7.2. Amaximum at 18 V 0.75 A maximum at 164 V Efficiency >75% at full load over full Input voltage range Current Limit Shutdown at maximum power with auto-recovery Over-Voltage Protection Crowbar protection set at 6.25 V Under-Voltage Protection ‘Shutdown at low input voltage Hold-up Time ‘Withstands 4 ms dead shorted power supply input Ripple and Noise 50 mV peak-peak (+5 V) 400 mV peakpeak (215 V) Isolation 2000 V ac RMS for 1 minute Primary-to-Chassis and Primary-to-Secondary Isolation Transient Protection IEC 255-4 class 3 (5 kV impulse, 2.5 kV HFD) ANSI IEEE C37.90.1 IEC 61000-4-4 Level 3 (2 kV) IEC 61000-4-5 Level 3 (2 kV) EMC Conducted Noise ENS0011 Class A Fall Alarm Output Relay output contact (normal open and normal closed) controlled by Electrobus SYSFAIL signal and #15 V ail fut LED Indications Input voltage OK, +15 V within limits On Board Fuse 10 A250 V Type T, 20x 5 mm ORDERING INFORMATION Part Number s¥-0702078 98 Commercial Sraet Foxboro Massachusetts 02005-2099 United hates of America ‘wo fendorecom Inte US: 1-000-740-0977 Description RTUSO 100 W Wide Input Range Power Supply Module (uiside U.S: 1-508-540-2424 or contact your local Foxboro represaalive Facsimile: 1-808-540-4200, Foxboro Austral 10 Brandl Street Eight Mie Plains, Srisbane Queensland 4173, ausraa “Telephone: 461 7-s340-2111 Fax 461 73340-2100 levenays, Foxboro, and UA Saris are trademarks of Invensys pels subsilals, and afstes, A oher brand namee may be trademarks of har raspacive owe. Copyright 1007-2003 Invaneys Systen, Ine. A rights resarved Ms 021 Prinedin US.A, 403SECTION A-3 RTU C50 DUAL COMMUNICATION MODULE