HISTORY INFORMATION FOR THE FOLLOWING MANUAL:

SERVICE MANUAL
ORIGINAL MANUAL ISSUE DATE: 1/2010 AZ1-L CHASSIS
Segment: 3a-1
Version Date Subject
1.0 1/2010 No revisions or updates are applicable at this time.
2.0 2/2010 Amend 32”(P.42) & 37”(P.45) EX504 ‘BAL’ board part number.
3.0 5/2010 Add updated Panel Caution Note (P.6).
Add Inverter and Tcon Board Part Numbers (P.42,45,48,51,54).
Add illustration showing location of neck to base screws (P.43,46,49,52,55).
Add ‘Support, Panel’ Part Numbers (P.41,44,47,50,53).
4.0 6/2010 Add ‘Hotel Assy’ to Exploded Views (P.41,44,47,50,53).
Add ‘Hotel Addendum’ for B2B Models (P.59). LCD Digital Color TV
5.0 1/2011 Add part number for 32” FRAME, BOTTOM (S) (P.41).
6.0 3/2011 Add part number for FRAME, BOTTOM (P44, 47, 50, 53)
Add BAL BOARD (HOTEL) (P42, 45, 48, 51, 54)

KDL-32/37/40/46/55EX500 9-888-265-06
Series(AEP/UK)
SERVICE MANUAL
AZ1-L CHASSIS
Segment: 3a-1

LCD Digital Color TV

KDL-32/37/40/46/55EX500 9-888-265-06
Series(AEP/UK)
 MODEL LIST
MODEL COLOR COMMANDER DEST. MODEL COLOR COMMANDER DEST.
KDL-32EX500 Black RM-ED035 AEP
KDL-32EX501 Black RM-ED035 AEP
KDL-32EX503 Black RM-ED035 UK
KDL-32EX504 Black RM-ED035 AEP
KDL-32EX505 Black RM-ED035 AEP
KDL-32EX508 Black RM-ED033 AEP
KDL-37EX500 Black RM-ED035 AEP
KDL-37EX503 Black RM-ED035 UK
KDL-37EX504 Black RM-ED035 AEP
KDL-37EX505 Black RM-ED035 AEP
KDL-40EX500 Black RM-ED035 AEP
KDL-40EX501 Black RM-ED035 AEP
KDL-40EX503 Black RM-ED035 UK
KDL-40EX505 Black RM-ED035 AEP
KDL-40EX508 Black RM-ED033 AEP
KDL-46EX500 Black RM-ED035 AEP
KDL-46EX501 Black RM-ED035 AEP
KDL-46EX503 Black RM-ED035 UK
KDL-46EX505 Black RM-ED035 AEP
KDL-55EX500 Black RM-ED035 AEP
KDL-55EX503 Black RM-ED035 UK
KDL-55EX505 Black RM-ED035 AEP

KDL-32/37/40/46/55EX500 Series(AEP/UK) 3
 WARNINGS AND CAUTIONS - ENGLISH

CAUTION
These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to
do so.

WARNING!!
An isolation transformer should be used during any service to avoid possible shock hazard, because of live chassis.
The chassis of this receiver is directly connected to the ac power line.

CARRYING THE TV
Be sure to follow these guidelines to protect your property and avoid causing serious injury.
• Carry the TV with an adequate number of people; larger size TVs require two or more people.
• Correct hand placement while carrying the TV is very important for safety and to avoid damages.

SAFETY-RELATED COMPONENT WARNING!!

Components identified by shading and ! mark on the schematic diagrams, exploded views, and in the parts list are critical for safe operation.
Replace these components with Sony parts whose part numbers appear as shown in this manual or in supplements published by Sony. Circuit
adjustments that are critical for safe operation are identified in this manual. Follow these procedures whenever critical components are replaced or
improper operation is suspected.

KDL-32/37/40/46/55EX500 Series(AEP/UK) 4
 WARNINGS AND CAUTIONS - FRENCH

ATTENTION!!
Ces instructions de service sont à l’usage du personnel de service qualifi é seulement.
Pour prévenir le risque de choc électrique, ne pas faire l’entretien autre que celui contenu dans le Mode d’emploi à moins que vous soyez qualifi é
faire ainsi.

WARNING!!
Afi n d’eviter tout risque d’electrocution provenant d’un chássis sous tension, un transformateur d’isolement doit etre utilisé lors de tout
dépannage. Le chássis de ce récepteur est directement raccordé à l’alimentation du secteur.

POUR TRANSPORTER LE TÉLÉVISEUR

Tenez compte de ce qui suit pendant l’installation du téléviseur :
• Débranchez tous les câbles avant de transporter le téléviseur.
• Transportez le téléviseur avec le nombre de personnes approprié ; un téléviseur de grande taille doit être transporté par au moins deux personnes.
• Lors du transport du téléviseur, l’emplacement des mains est très important pour votre sécurité, ainsi que pour éviter de causer des dommages.

ALERTE!!
Afi n d’eviter tout risque d’electrocution provenant d’un chassis sous tension, un transformateur d’isolement doit etre utilise lors de tout
depannage. Le chassis de ce recepteur est directement raccorde a l’alimentation du secteur.

ATTENTION AUX COMPOSANTS RELATIFS A LA SECURITE!!

Les composants identifi es par une trame et par une marque ! sur les schemas de principe, les vues explosees et les listes de pieces sont d’une
importance critique pour la securite du fonctionnement. Ne les remplacer que par des composants Sony dont le numero de piece est indique dans
le present manuel ou dans des supplements publies par Sony. Les reglages de circuit dont l’importance est critique pour la securite du
fonctionnement sont identifi es dans le present manuel. Suivre ces procedures lors de chaque remplacement de composants critiques, ou lorsqu’un
mauvais fonctionnement suspecte.

KDL-32/37/40/46/55EX500 Series(AEP/UK) 5
 WARNINGS AND CAUTIONS

USE CAUTION WHEN HANDLING THE LCD PANEL

When repairing the LCD panel, be sure you are grounded by using a wrist band.
When repairing the LCD panel on the wall, the LCD panel must be secured using the 4 mounting holes on the rear cover.

1) Do not press on the panel or frame edge to avoid the risk of electric shock.
2) Do not scratch or press on the panel with any sharp objects.
3) Do not leave the module in high temperatures or in areas of high humidity for an extended period of time.
4) Do not expose the LCD panel to direct sunlight.
5) Avoid contact with water. It may cause a short circuit within the module.
6) Disconnect the AC power when replacing the backlight (CCFL) or inverter circuit. (High voltage occurs at the inverter circuit at 650Vrms.)
7) Always clean the LCD panel with a soft cloth material.
8) Use care when handling the wires or connectors of the inverter circuit. Damaging the wires may cause a short.
9) Protect the panel from ESD to avoid damaging the electronic circuit (C-MOS).
10) It is recommended not to exceed 1 hour of Power-On nor Burn-in period with LCD panel face down condition, in repair activity.

KDL-32/37/40/46/55EX500 Series(AEP/UK) 6
 SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before
releasing the set to the customer:

1. Check the area of your repair for unsoldered or poorly soldered connections. Check the entire
board surface for solder splashes and bridges.
2. Check the interboard wiring to ensure that no wires are “pinched” or touching high-wattage
resistors.
3. Check that all control knobs, shields, covers, ground straps, and mounting hardware have been
replaced. Be absolutely certain that you have replaced all the insulators.
4. Look for unauthorized replacement parts, particularly transistors, that were installed during a
previous repair. Point them out to the customer and recommend their replacement.
5. Look for parts which, though functioning, show obvious signs of deterioration. Point them out
to the customer and recommend their replacement.
6. Check the line cords for cracks and abrasion. Recommend the replacement of any such line
cord to the customer.
7. Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed
metal parts for AC leakage. Check leakage as described below.
8. For safety reasons, repairing the Power board and/or Inverter board is prohibited.

KDL-32/37/40/46/55EX500 Series(AEP/UK) 7
 SAFETY CHECK-OUT

Leakage Test
The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to
any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.

1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the
manufacturers’ instructions to use these instructions.
2. A battery-operated AC milliampmeter. The Data Precision 245 digital multimeter is suitable
for this job.
3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC
voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low
voltage scale.
The Simpson’s 250 and Sanwa SH-63TRD are examples of passive VOMs that are suitable.
Nearly all battery-operated digital multimeters that have a 2 VAC range are suitable (see
Figure A).

How to Find a Good Earth Ground

A cold-water pipe is a guaranteed earth ground; the cover-plate retaining screw on most AC outlet
boxes is also at earth ground.
If the retaining screw is to be used as your earth ground, verify that it is at ground by measuring the
resistance between it and a cold-water pipe with an ohmmeter. The reading should be zero ohms.
If a cold-water pipe is not accessible, connect a 60- to 100-watt trouble- light (not a neon lamp)
between the hot side of the receptacle and the retaining screw. Try both slots, if necessary, to
locate the hot side on the line; the lamp should light at normal brilliance if the screw is at ground
potential (see Figure B).

KDL-32/37/40/46/55EX500 Series(AEP/UK) 8
 SELF DIAGNOSIS FUNCTION
The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY LED will automatically begin to flash.
The number of times the LED flashes translates to a probable source of the problem.
A definition of the STANDBY LED flash indicators is listed in the instruction manual for the user’s knowledge and reference.
If an error symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past
problems and how often these problems occur.

DIAGNOSTIC TEST INDICATORS

STBY LED Service menu Item name
When an error occurs, the STANDBY LED will flash a set number Diagnostic Item Description
Flash time (Screen Display)
of times to indicate the possible cause of the problem. 2 MAIN_POWE Main Power Over Voltage Protection
If there is more than one error, the LED will identify the first of the 3 DC_ALERT DC_ALERT
problem areas. DTT_WDT DTT Error
Result for all of the following diagnostic items are displayed on AUD_PROT Audio Abnormal Detection
screen. 4 BALANCER_ Panel Balancer Error
If the screen displays a “0”, no error has occurred . 5 TCON_ERR T-CON Error
HFR_ERR HFR Error
P_ID_ERR Panel ID NVM Error
6 BACKLITE_ Back Light Error (Panel Inverter)
7 TEMP_ERR Thermal Error
FAN_ERR FAN Error (Not Detected. Display Only)
8 - Not used
9 - Not used
10 - Not used
11 - Not used
12 - Not used
- RGB_SEN RGB Sensor ACK Error

KDL-32/37/40/46/55EX500 Series(AEP/UK) 9
 SELF DIAGNOSIS FUNCTION

DISPLAY OF STANDBY LED FLASH COUNT

0.5
0.5
3

SELF-DIAGNOSTIC SCREEN DISPLAY

For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it is possible to bring up
past occurrences of failure for confirmation on the screen:

[To Bring Up Screen Test]

In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:

KDL-32/37/40/46/55EX500 Series(AEP/UK) 10
 SELF DIAGNOSIS FUNCTION

[SELF DIAGNOSTIC SCREEN DISPLAY]

SELF CHECK(1) <1> NEXT PAGE->

002 MAIN P 0501210811 0412311234 0311111825 00

003 DC_ALERT1 0000000000 0000000000 0000000000 00
004 DC_ALERT2 0000000000 0000000000 0000000000 00

006 BL 0000000000 0000000000 0000000000 00

007 TEMP 0000000000 0000000000 0000000000 00

009 FAN 0000000000 0000000000 0000000000 00

Error count (00-99)
Error history (Last failure time beforehand)
Error history (Failure time before last)
Error history (The last failure time)
Item name
STBY LED flash time

12345-00333-06789

Panel operation time by hour (MAX:65535)

Boot count (MAX:65535)

Total operation time by hour (MAX:65535)

KDL-32/37/40/46/55EX500 Series(AEP/UK) 11
 SELF DIAGNOSIS FUNCTION

Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen.
After you have completed the repairs, clear the result display to “0”.

Clearing the Self Check Diagnostic List

1. Error history and Error count : Press the Channel 8 => Channel 0 .
2. Panel operation time : Press the Channel 7 => Channel 0 .

Exiting the Self-diagnostic screen

To exit the Self Diagnostic screen, turn off the power to the TV by pressing the POWER button on the remote or the POWER button on
the TV.

KDL-32/37/40/46/55EX500 Series(AEP/UK) 12
 SEC 1. DISASSEMBLY
1-1. MOVIE LIST

KDL-32EX500
KDL-32EX500 Series
Series
KDL-37EX500
KDL-37EX500 Series
Series

KDL-40EX500
KDL-40EX500 Series
Series

KDL-46EX500
KDL-46EX500 Series
Series

KDL-55EX500
KDL-55EX500 Series
Series

KDL-32/37/40/46/55EX500 Series(AEP/UK) 13
 SEC 2. ADJUSTMENT
HOW TO ENTERING SERVICE MODE
1) Turn on the main power switch to place this set in standby mode.
2) Press the buttons on the remote commander as follows, and entering service mode.

3) Service mode display.

Note: First of all, when you enter Service Mode, you can see “Digital” service mode.
Whenever you press “OPTIONS” or “JUMP” on remote, each service mode is changed.
“Digital” -> “Chassis” -> “Sub”

Item name
CHASSIS SERVICE
DIGITAL SERVICE Item number 000 CXD2813R
Category name
000 H_DET_NOSIG_CNT 1
001 OP
000 VERS --- Category number
Data

<MAIN> <SUB>
DM1.301J00AA SM1.010W00AA
M2.105C SB1.000W00AA
DD1.016J00AA SD1.010W00AA
(DM1.301J00AA) RF01.05 Press “OPTIONS”
WP00.521J00AA ID1C117081
ID1C117081 LTY320AB01 or “JUMP” button
PID04020000
WF:2.0.0.99 <BEM>
WF:0B BM1.012W00LU
Camera FW BB1.000W00LU
Camera FW BD1.011J46LUX
---.---------

KDL-32/37/40/46/55EX500 Series(AEP/UK) 14
 ADJUSTMENT

4) How to use the remote commander.

Function The flow of control

Service mode on <Test>+<TV>/<Display><5><Vol Up><Power>

Service mode off <Other> / <Power off + on>

Item up / down <1>/<4>
Category up / down <2>/<5>
Data up / down <3>/<6>

Test reset <8> + <Mute> + <0>

Read data <9> + <0>
Execute <10 or 0>
Write data <Mute> + <0>

Change module <Jump> / <Option>

5) After entering service mode, then turn off the power switch.

KDL-32/37/40/46/55EX500 Series(AEP/UK) 15
 ADJUSTMENT

WHITE BALANCE ADJUSTMENT

Change Data of “Digital” service mode. (“006 WB” category)
a. Press “0” or “10” on remote to enter WB adjustment mode.
b. Press number key “1”~”6” directly. “*” stamp move.
c. Press “12 / enter / select” to decide and advance next step.
When returning on the previous page, press “return”.
d. Change data by number key “0”~”9” directly. (0-255)
e. Press “12 / enter / select” to save data.
It shows red “WRITE”. It indicate writing is processing.
f. Writing process is done at this point.

DIGITAL SERVICE
DIGITAL SERVICE WB
006 WB *1 R_DRV 128
000 WHITE_BALANCE ___ 2 G_DRV 128 Gain
0: x 0.5, 128: x 1, 255: x1.5
3 B_DRV 128
4 R_BKG 128
5 G_BKG 128 Offset
6 B_BKG 128 128: offset 0

Please input WB items

(0-255)
---

KDL-32/37/40/46/55EX500 Series(AEP/UK) 16
 ADJUSTMENT

SAVE CHANGING DATA

1) Change Data of “Chassis” or “Sub” service mode
2) Write data for “Chassis” or “Sub” service mode
a. Press “Mute” on remote.
It shows green “SERVICE” changes to green “WRITE”.
b. Press “0” or “enter” on remote. Green “WRITE” changes to red “WRITE”. It indicate writing is processing.
c. After a while, red “WRITE” changes to green “SERVICE”. Writing process is done at this point.
3) TV reboot is necessary for applying data change.

CHASSIS WRITE
000 CXD2813R
000 H_DET_NOSIG_CNT 1

KDL-32/37/40/46/55EX500 Series(AEP/UK) 17
 ADJUSTMENT

CHANGE DATA
Note: “Digital” service mode don’t have to Save. (except “002 MODEL” category)
1) Change Data of “Digital” service mode. (except “003 DIG_SRV_MODE” category)
DIGITAL SERVICE
a. Press “2 / 5” on remote to select (up / down) category. 004 TUNER
b. Press “1 / 4” on remote to select (up / down) Item. 000 A_NOSIG_DET 001
c. Press “0 / 10” on remote to select item.

2) Change Data of “Digital” service mode. ( “003 DIG_SRV_MODE” category)

“003 DIG_SRV_MODE” is one category of “Digital” service mode. DIGITAL SERVICE
Please note because this operation is special. 003 DIG_SRV_MODE
a. Press “2 / 5” on remote to select “003 DIG_SRV_MODE”. 000 TEST_PATTERN ---
b. Press “1 / 4” on remote to select (up / down) Item.
c. Press “0 / 10” on remote to select item.
d. Press number key “1”~”9” directly. “*” stamp move.
e. Press “12 / enter / select” to decide and advance next step. Press “return”,
when returning on the previous page.

DIGITAL(DIG_SRV_MODE) SERVICE

TEST_PATTERN

*1 Video
2 Audio

KDL-32/37/40/46/55EX500 Series(AEP/UK) 18
 ADJUSTMENT

3) Write data for “Digital” service mode. ( “002 MODEL” category)

Note: This procedure operation, when replaced the B board. DIGITAL SERVICE
Note: Do not write a wrong segment or destination information in Product ID. 002 MODEL
When the wrong setting is written, TV may not operate. 000 SEG 01 : 2a-3
Write
000 SEG ・・・Product ID - segment information
001 DEST・・・Product ID – destination information
a. Change data for each model.
b. Press “0” or “enter” on remote.
It shows red “WRITE”. It indicate writing is processing.
c. Writing process is done at this point.

KDL-32/37/40/46/55EX500 Series(AEP/UK) 19
 ADJUSTMENT

SET TO SHIPPING CONDITION

How to do shipping condition.
a. Move to “Digital” service mode.
Press “8” on remote.
It shows green “SERVICE” changes to green “RST-”.
Press “mute” on remote.
Added green “EXE” after green “RST-” .
d. Press “0” or “enter” on remote. Green “EXE-RST” changes to red “EXE-RST”. It indicate writing is processing.
After a while, red “EXE-RST” changes to green “SERVICE”.
And all LED lights.
Writing process is done at this point.

TIMER Standby POWER

<Another way>
You can set to shipping condition w/o entering Service Mode.
-> “Cursor Up” on remote + “Power Key” on Front panel.

KDL-32/37/40/46/55EX500 Series(AEP/UK) 20
 SEC 3. TROUBLE SHOOTING
3-1. TRIAGE CHART
Note: Power board is different in name every inch. Therefore this section displays difference point in "*".

Symptoms - Shutdown. Power LED No

Video - missing or distorted Remote Network Audio
blinking red diagnostics sequences Power
Reference No Green Stationary Wireless
No video No video No
2 3 4 5 6 7 Power LED colored lines can't No Audio
one of Inputs all Inputs Remote
(Dead Set) or dots connect
BAL BOARD
G* BOARD
HLR BOARD
WiFi MODULE
D1 BOARD
LVDS CABLE
LCD PANEL
POWER
PANEL PANEL
Problem POWER DTT POWER TEMP
(TCON) (INVERTER)
AUDIO

: doubtful part
: Few possibility

KDL-32/37/40/46/55EX500 Series(AEP/UK) 21
 TROUBLE SHOOTING

3-2. FLOW CHART

START

Does the Power Led No No

See Is the network See
stay on when the
No Power connection OK? Can’t connect network
TV is switched on ?

Yes Yes

END
Is the Standby Led No See
blink ? Standby LED Blink

Yes

Is the Picture and No See

Sound OK ? No Picture / No Sound

Yes

Do the buttons
No See
on the TV & Remote
TV/ Commander
Commander work
button malfunction
properly?

Yes

KDL-32/37/40/46/55EX500 Series(AEP/UK) 22
 TROUBLE SHOOTING

3-3. NO POWER

No Power

Check STBY 3.3V NG Replace NG

at 1 pin of CN3800 Between G* Board to G* Board
on the BAL Board BAL Board Harness

OK OK

Harness

BAL Board

KDL-32/37/40/46/55EX500 Series(AEP/UK) 23
 TROUBLE SHOOTING

3-4. STANDBY LED BLINK

1) 2 times blinkings (Main Power Error)

2 times Blinkings

Check REG12V at 12V NG NG

Replace
pins 6/7 of
Between G* Board to G* Board
CN3800 on
BAL Board Harness
the BAL Board

12V OK OK

BAL Board Harness

KDL-32/37/40/46/55EX500 Series(AEP/UK) 24
 TROUBLE SHOOTING

2) 3 times blinkings (DC Alert, Audio Error and Communication Error)

3 times Blinkings AUDIO

Check +12.5V NG
DC_ALERT at pin 2 of
G* Board
CN3800 on
Check D+3.3V at NG the BAL Board
F3700,IC3700,etc
JL3715 or JL3716
(BAL Board) OK
on the BAL Board

OK NG
Check +12.5V_AU1
F4200,IC4200,etc
at F4200 on
(BAL Board)
the BAL Board
Check +5V_MAIN NG
F3701,IC3701,etc
at JL3731 or JL3732 on
(BAL Board) OK
the BAL Board

OK Check Pin: Low

X_ASW_PROTECT IC4200,etc
AUDIO at pin 29 of IC5000 (BAL Board)
on the BAL Board

Check NG Pin: High

Speaker Impedance Speaker
at SP Connector

FE/BE Communication
OK
IC9000,etc
(BAL Board)

KDL-32/37/40/46/55EX500 Series(AEP/UK) 25
 TROUBLE SHOOTING

3) 4 times blinkings (Balancer Error)

4 times Blinkings

Between 0.84V to 2.65V

Check
PANEL_FAIL at PANEL
JL2565 (Balancer)
on the BAL Board

BAL Board

KDL-32/37/40/46/55EX500 Series(AEP/UK) 26
 TROUBLE SHOOTING

4) 5 times blinkings (T-con Error)

5 times Blinkings

NG NG
Check PANEL_VCC
Panel (T-con)
at JL3806 G* Board BAL Board
change
on the BAL Board

OK about 12V OK

NG Panel (T-con)
Between G* to Panel
Harness
harness check

OK

NG
LVDS Harness
LVDS Harness
check

OK

KDL-32/37/40/46/55EX500 Series(AEP/UK) 27
 TROUBLE SHOOTING

5) 6 times blinkings (Backlight Error) 6) 7 times blinkings (Temperature Error)

6 times Blinkings 7 times Blinkings

Under 2.65V
Check Setting circumstance NO
PANEL_FAIL at is OK? Set to another
BAL Board
JL2565 Temperature, Location, etc.
on the BAL Board Ventilation, etc.

Over 2.65V YES

OK NG
Change BAL Board,
Change D1 Board Inverter (D1 Board) Panel
and Aging a few hours

NG OK

NG BAL Board
Change G* Board Panel (T-con)

OK

G* Board

KDL-32/37/40/46/55EX500 Series(AEP/UK) 28
 TROUBLE SHOOTING

3-5. NO PICTURE

No Picture

about 12V

NO YES BL_ON:H NG
PANEL_VCC Check
Press HOME Key Replace LCD Panel
At JL3806 on the BL_ON at JL2566
XMB (Menu) displayed? the LVDS Harness (T-con)
BAL Board on the BAL Board

YES NO BL_ON: not H OK

BAL Board Check Harness NG

Harness Harness
G* Board (Between G* Board
(G* to BAL) (LVDS)
to BAL Board)

OK

NG
Change BAL Board G* Board

OK

BAL Board

KDL-32/37/40/46/55EX500 Series(AEP/UK) 29
 TROUBLE SHOOTING

3-6. NO SOUND

No Sound

“Audio System”
Check the Change to
“Speakers setting” “TV Speaker”

“TV Speakers”

OK OK
Check the Speaker Replace
BAL Board
Harness the BAL Board

NG NG

Speaker Harness Speaker

KDL-32/37/40/46/55EX500 Series(AEP/UK) 30
 TROUBLE SHOOTING

3-7. TV COMMANDER BUTTONS MALFUNCTION

1) TV button malfunction

Button malfunction
on the TV

OK OK
BAL to Switch Unit
Switch Unit change Switch Unit
harness check

NG NG

Harness BAL Board

KDL-32/37/40/46/55EX500 Series(AEP/UK) 31
 TROUBLE SHOOTING

2) IR remote commander malfunction

TV isn’t controlled
by remote commander

OK Green LED blinks OK

Green LED light at power indicator Mechanical
at power indicator when using commander (ex. bezel)
near sensor’s window

NG NG

Check the Harness OK

between the BAL Board Sensor is broken
and the HLR Board

NG
OK
Exchange the Harness Harness

NG

Exchange the OK
HLR Board
HLR Board

NG

BAL Board

KDL-32/37/40/46/55EX500 Series(AEP/UK) 32
 TROUBLE SHOOTING

3-8. NETWORK MALFUNCTION

1) Wired Network malfunction 2) USB Wireless Network malfunction

Wired Network Wireless Network

on the TV on the TV

NG Error Message appear YES

Connection result
BAL Board when the Wireless USB Dongle
Cable Connection
Network is selected?

OK NO

NG Is the radio field YES

Connection result
Ether net cable Strength too weak Access Point
Local Access
or even No signal?

OK NO

NG BAL Board
Connection result
Proxy setting
Internet Access

KDL-32/37/40/46/55EX500 Series(AEP/UK) 33
 SEC 4. DIAGRAMS
4-1. BLOCK DIAGRAM

KDL-32/37/40/46/55EX500 Series(AEP/UK) 34
 DIAGRAMS

4-2. CIRCUIT BOARDS LOCATION

(1) KDL-32EX500 Series

T-CON

G2ME Board

Inverter
BAL Board

Switch Unit

Speaker (L)

Speaker (R) HLR Board

KDL-32/37/40/46/55EX500 Series(AEP/UK) 35
 DIAGRAMS

(2) KDL-37EX500 Series

T-CON

G2HE Board

Inverter
BAL Board

Switch Unit

Speaker (L)

Speaker (R) HLR Board

KDL-32/37/40/46/55EX500 Series(AEP/UK) 36
 DIAGRAMS

(3) KDL-40EX500 Series

T-CON

G2HE Board

Inverter

BAL Board

Switch Unit

Speaker (L)

Speaker (R) HLR Board

KDL-32/37/40/46/55EX500 Series(AEP/UK) 37
 DIAGRAMS

(4) KDL-46EX500 Series

T-CON

GD2 Board

Inverter

BAL Board

Switch Unit
Speaker (L)

Speaker (R) HLR Board

KDL-32/37/40/46/55EX500 Series(AEP/UK) 38
 DIAGRAMS

(5) KDL-55EX500 Series

T-CON

D1Board

G5E Board

Inverter

BAL Board

Switch Unit
Speaker (L)

Speaker (R) HLR Board

KDL-32/37/40/46/55EX500 Series(AEP/UK) 39
 SEC 5. EXPLODED VIEWS
• Items with no part number and no description are not stocked because they are seldom required for roution service.
• The construction parts of an assembled part are indicated with a collation number in the remark colum.
• Items marked " * " are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.

KDL-32/37/40/46/55EX500 Series(AEP/UK) 40
 EXPLODED VIEWS

5-1. KDL-32EX500 SERIES

5-1-1. CHASSIS-1

REF. No. PART No. DESCRIPTION REMARK

11a
1 1-858-364-22 LOUDSPEAKER (12.5x4.5CM)
2 4-166-121-11 BRACKET, SP (32L)
3 4-166-122-11 BRACKET, SP (32R)
11b 4 1-487-728-11 SWITCH UNIT
5 4-166-124-11 COVER, UNDER (32)
1 6 4-158-349-01 NECK (M3)
7 X-2546-541-1 COVER (M3) ASSY
2 8 X-2546-980-1 BASE (M3) ASSY
9 X-2546-624-1 REAR COVER (TR32) ASSY
11 X-2547-420-1 REAR COVER (32_SAT) ASSY EX505,508
5 10 *3-106-546-51 COVER,ECS
HOTEL ASSY See Hotel Addendum
11 4-167-326-01 BRACKET, VESA (S)
11a 4-166-118-11 SUPPORT, PANEL
1 6 11b 4-156-936-01 FRAME, BOTTOM (S)

3 10

Note:
7
Whenever removing the ‘Rear Cover’ on B2B models
9 remember to remove the connector inside the ‘Hotel
4 Assy’ on the ‘R2’ board first.

KDL-32/37/40/46/55EX500 Series(AEP/UK) 41
 EXPLODED VIEWS

5-1. KDL-32EX500 SERIES

5-1-2. CHASSIS-2

REF. No. PART No. DESCRIPTION REMARK

12
12 X-2546-599-1 BEZEL ASSY (32TR_MET) EX500,503,504,505
X-2546-744-1 BEZEL ASSY (32TR_BCK) EX501,EX508
13 A-1753-636-A HLR MOUNT
14 4-166-268-01 BRACKET, SIDE JACK
20 15 1-811-054-11 LCD PANEL (S32TDP)
16 1-474-201-21 STATIC CONVERTER (TV)
13
17 A-1760-331-A BAL BOARD COMPLETE EX500,501
A-1796-761-A BAL BOARD (HOTEL) EX500
A-1768-994-A BAL BOARD COMPLETE EX503
14 A-1796-762-A BAL BOARD (HOTEL) EX503
A-1769-581-A BAL BOARD COMPLETE EX505,508
A-1780-319-A BAL BOARD COMPLETE EX504
18 1-837-454-11 POWER-SUPPLY CORD
19 1-857-634-11 INVERTER BOARD
20 1-489-034-11 TCON BOARD

15 17

16
19
18

KDL-32/37/40/46/55EX500 Series(AEP/UK) 42
 EXPLODED VIEWS

5-1. KDL-32EX500 SERIES

5-1-3. SCREWS

PART No. DESCRIPTION

2-580-640-01 SCREW, +BVTP 4X16 TYPE2 IT-3
2-580-595-01 SCREW, +PSW M3X12
7-685-648-79 SCREW +BVTP 3X12 TYPE2 IT-3
2-580-608-01 SCREW, +PSW M5X16
2-580-592-01 SCREW, +PSW M3X8
4-159-298-01 SCREW, +PSW M4X10

KDL-32/37/40/46/55EX500 Series(AEP/UK) 43
 EXPLODED VIEWS

5-2. KDL-37EX500 SERIES

5-2-1. CHASSIS-1

REF. No. PART No. DESCRIPTION REMARK

8a
1 1-487-728-11 SWITCH UNIT
2 4-166-123-11 COVER, UNDER (37)
3 4-158-350-01 NECK (ML3)
9 4 X-2546-541-1 COVER (M3) ASSY
5 X-2541-845-1 BASE (ML3) ASSY
6 X-2546-655-1 REAR COVER (TR37) ASSY
X-2547-422-1 REAR COVER (37_SAT) ASSY EX505
7 *3-106-546-51 COVER,ECS
8
HOTEL ASSY See Hotel Addendum
8 4-167-326-01 BRACKET, VESA (S)
2 8a 4-166-118-01 SUPPORT, PANEL
9 4-156-937-11 FRAME, BOTTOM (M)

3
7

Note:
4
6 Whenever removing the ‘Rear Cover’ on B2B models
remember to remove the connector inside the ‘Hotel
1 Assy’ on the ‘R2’ board first.
5

KDL-32/37/40/46/55EX500 Series(AEP/UK) 44
 EXPLODED VIEWS

5-2. KDL-37EX500 SERIES

5-2-2. CHASSIS-2

REF. No. PART No. DESCRIPTION REMARK

9
9 X-2546-657-1 BEZEL ASSY (TR37_MET)
10 A-1753-636-A HLR MOUNT
11 4-166-268-01 BRACKET, SIDE JACK
20 12 1-811-077-11 LCD PANEL (A37V9)
10
13 1-474-202-21 STATIC CONVERTER (TV)
11
14 A-1760-331-A BAL BOARD COMPLETE EX500,501
A-1796-761-A BAL BOARD (HOTEL) EX500
A-1768-994-A BAL BOARD COMPLETE EX503
A-1796-762-A BAL BOARD (HOTEL) EX503
A-1769-581-A BAL BOARD COMPLETE EX505
A-1780-319-A BAL BOARD COMPLETE EX504
15 1-837-454-11 POWER-SUPPLY CORD
16 1-858-364-22 LOUDSPEAKER (12.5x4.5CM)
15 17 4-166-121-11 BRACKET, SP (37L)
14
12 18 4-166-122-11 BRACKET, SP (37R)
19 1-857-701-11 INVERTER BOARD
20 1-857-700-11 TCON BOARD

13 16
19
17

18

KDL-32/37/40/46/55EX500 Series(AEP/UK) 45
 EXPLODED VIEWS

5-2. KDL-37EX500 SERIES

5-2-3. SCREWS

PART No. DESCRIPTION

2-580-640-01 SCREW, +BVTP 4X16 TYPE2 IT-3
2-580-595-01 SCREW, +PSW M3X12
7-685-648-79 SCREW +BVTP 3X12 TYPE2 IT-3
2-580-608-01 SCREW, +PSW M5X16
2-580-592-01 SCREW, +PSW M3X8
4-159-298-01 SCREW, +PSW M4X10

KDL-32/37/40/46/55EX500 Series(AEP/UK) 46
 EXPLODED VIEWS

5-3. KDL-40EX500 SERIES

5-3-1. CHASSIS-1

REF. No. PART No. DESCRIPTION REMARK

8a
1 1-487-728-11 SWITCH UNIT
2 4-166-123-11 COVER, UNDER (37)
3 4-158-350-01 NECK (ML3)
4 X-2546-541-1 COVER (M3) ASSY
5 X-2541-845-1 BASE (ML3) ASSY
9
6 X-2546-618-1 REAR COVER (TR40) ASSY
X-2547-412-1 REAR COVER (TR40_SAT) ASSY EX505,508
7 *3-106-546-51 COVER,ECS
8
HOTEL ASSY See Hotel Addendum
2 8 4-167-326-01 BRACKET, VESA (S)
8a 4-166-118-01 SUPPORT, PANEL
9 4-156-938-02 FRAME, BOTTOM (ML)

3
1 Note:
4 6 Whenever removing the ‘Rear Cover’ on B2B models
remember to remove the connector inside the ‘Hotel
Assy’ on the ‘R2’ board first.
5

KDL-32/37/40/46/55EX500 Series(AEP/UK) 47
 EXPLODED VIEWS

5-3. KDL-40EX500 SERIES

5-3-2. CHASSIS-2

REF. No. PART No. DESCRIPTION REMARK

9
9 X-2546-615-1 BEZEL ASSY (TR40_MET) EX500,503,505
X-2546-769-1 BEZEL ASSY (TR40_BCK) EX501,508
10 A-1753-636-A HLR MOUNT
11 4-166-268-01 BRACKET, SIDE JACK
20 12 1-811-055-12 LCD PANEL (S40TDP)
10
13 1-474-202-21 STATIC CONVERTER (TV)
11 14 A-1760-331-A BAL BOARD COMPLETE EX500,501
A-1796-761-A BAL BOARD (HOTEL) EX500
14 A-1768-994-A BAL BOARD COMPLETE EX503
A-1796-762-A BAL BOARD (HOTEL) EX503
A-1769-581-A BAL BOARD COMPLETE EX505,508
15 1-837-454-11 POWER-SUPPLY CORD
1-837-455-11 POWER-SUPPLY CORD (UK) EX503
16 1-858-364-22 LOUDSPEAKER (12.5x4.5CM)
15 17 4-166-119-11 BRACKET, SP (40L)
18 4-166-120-11 BRACKET, SP (40R)
12 19 1-857-640-11 INVERTER BOARD
20 1-857-648-11 TCON BOARD

16
13
19
17

18

KDL-32/37/40/46/55EX500 Series(AEP/UK) 48
 EXPLODED VIEWS

5-3. KDL-40EX500 SERIES

5-3-3. SCREWS

PART No. DESCRIPTION

2-580-640-01 SCREW, +BVTP 4X16 TYPE2 IT-3
2-580-595-01 SCREW, +PSW M3X12
7-685-648-79 SCREW +BVTP 3X12 TYPE2 IT-3
2-580-608-01 SCREW, +PSW M5X16
2-580-592-01 SCREW, +PSW M3X8
4-159-298-01 SCREW, +PSW M4X10

KDL-32/37/40/46/55EX500 Series(AEP/UK) 49
 EXPLODED VIEWS

5-4. KDL-46EX500 SERIES

5-4-1. CHASSIS-1

REF. No. PART No. DESCRIPTION REMARK

9a
1 1-487-728-11 SWITCH UNIT
2 4-166-123-31 COVER, UNDER (37)
3 4-158-350-01 NECK (ML3)
4 X-2546-541-1 COVER (M3) ASSY
5 X-2541-846-1 BASE (L3) ASSY
9b
6 X-2546-628-1 REAR COVER (TR46) ASSY
X-2547-418-1 REAR COVER (46_SAT) ASSY EX505
7 *3-106-546-51 COVER,ECS
2 HOTEL ASSY See Hotel Addendum
9 8 1-842-008-11 AC INLET FILTER
9 4-167-326-01 BRACKET, VESA (S)
9a 4-166-118-01 SUPPORT, PANEL
9b 4-156-938-02 FRAME, BOTTOM (ML)

8
7

3
Note:
1 4 Whenever removing the ‘Rear Cover’ on B2B models
6
remember to remove the connector inside the ‘Hotel
Assy’ on the ‘R2’ board first.
5

KDL-32/37/40/46/55EX500 Series(AEP/UK) 50
 EXPLODED VIEWS

5-4. KDL-46EX500 SERIES

5-4-2. CHASSIS-2

REF. No. PART No. DESCRIPTION REMARK

10
10 X-2546-629-1 BEZEL ASSY (TR46_MET) EX500,503,505
X-2546-746-1 BEZEL ASSY (TR46_BCK) EX501
11 A-1753-636-A HLR MOUNT
11 12 4-166-268-01 BRACKET, SIDE JACK
21
13 1-811-056-12 LCD PANEL (S46TDP)
14 1-474-205-11 STATIC CONVERTER (TV)-GD2
12
15 A-1760-331-A BAL BOARD COMPLETE EX500,501
A-1796-761-A BAL BOARD (HOTEL) EX500
A-1768-994-A BAL BOARD COMPLETE EX503
A-1796-762-A BAL BOARD (HOTEL) EX503
A-1769-581-A BAL BOARD COMPLETE EX505
16 1-837-639-11 POWER-SUPPLY CORD EX500,501,505
1-837-640-11 POWER-SUPPLY CORD EX503
17 1-858-371-11 LOUDSPEAKER (20x4.5CM)
18 4-157-973-11 BRACKET, SP (46L)
16 15
19 4-157-974-11 BRACKET, SP (46R)
13
20 1-857-643-11 INVERTER BOARD
21 1-857-650-11 TCON BOARD

14
17
20

18

19

KDL-32/37/40/46/55EX500 Series(AEP/UK) 51
 EXPLODED VIEWS

5-4. KDL-46EX500 SERIES

5-4-3. SCREWS

PART No. DESCRIPTION

2-580-640-01 SCREW, +BVTP 4X16 TYPE2 IT-3
2-580-595-01 SCREW, +PSW M3X12
7-685-648-79 SCREW +BVTP 3X12 TYPE2 IT-3
2-580-608-01 SCREW, +PSW M5X16
2-580-592-01 SCREW, +PSW M3X8
4-159-298-01 SCREW, +PSW M4X10
2-580-629-01 SCREW, +BVST 3X8
4-167-964-01 SCREW, +PWTP2 4X16

KDL-32/37/40/46/55EX500 Series(AEP/UK) 52
 EXPLODED VIEWS

5-5. KDL-55EX500 SERIES

5-5-1. CHASSIS-1

REF. No. PART No. DESCRIPTION REMARK

10a
1 1-487-749-11 SWITCH UNIT
2 4-157-979-11 COVER, UNDER (55)
3 4-158-351-01 NECK (LL3)
4 X-2546-543-1 COVER LL3) ASSY
5 X-2541-847-1 BASE (LL3) ASSY
10
6 X-2546-580-1 REAR COVER (55TR) ASSY
10b
X-2547-421-1 REAR COVER (55 SAT) ASSY EX505
7 *3-106-546-51 COVER,ECS
9 HOTEL ASSY See Hotel Addendum
2
8 1-842-009-11 AC INLET FILTER
9 4-167-326-01 BRACKET, VESA (S)
10 4-156-946-01 BRACKET, VESA (XL)
10a 4-166-118-11 SUPPORT, PANEL
10b 4-156-939-02 FRAME, BOTTOM (XL)

8
7

3
Note:
4 6
1 Whenever removing the ‘Rear Cover’ on B2B models
remember to remove the connector inside the ‘Hotel
Assy’ on the ‘R2’ board first.
5

KDL-32/37/40/46/55EX500 Series(AEP/UK) 53
 EXPLODED VIEWS

5-5. KDL-55EX500 SERIES

5-5-2. CHASSIS-2

REF. No. PART No. DESCRIPTION REMARK

11
11 X-2546-579-1 BEZEL ASSY (TR55_MET)
12 A-1753-636-A HLR MOUNT
13 4-166-268-01 BRACKET, SIDE JACK
13
14 1-811-057-12 LCD PANEL (S55TDP)
12 21
15 1-474-203-11 STATIC CONVERTER (TV)
16 1-474-206-11 STATIC CONVERTER (TV)-D1
17 A-1760-331-A BAL BOARD COMPLETE EX500,EX501
A-1796-761-A BAL BOARD (HOTEL) EX500
A-1768-994-A BAL BOARD COMPLETE EX503
A-1796-762-A BAL BOARD (HOTEL) EX503
A-1769-581-A BAL BOARD COMPLETE EX505
18 1-858-354-11 LOUDSPEAKER
17 19 1-837-639-11 POWER-SUPPLY CORD EX500,501,505
1-837-640-11 POWER-SUPPLY CORD EX503
20 1-857-653-11 INVERTER BOARD
21 1-857-652-11 TCON BOARD
14 16

15 18
19

20
18

KDL-32/37/40/46/55EX500 Series(AEP/UK) 54
 EXPLODED VIEWS

5-5. KDL-55EX500 SERIES

5-5-3. SCREWS

PART No. DESCRIPTION

2-580-640-01 SCREW, +BVTP 4X16 TYPE2 IT-3
2-580-595-01 SCREW, +PSW M3X12
7-685-648-79 SCREW +BVTP 3X12 TYPE2 IT-3
2-580-608-01 SCREW, +PSW M5X16
2-580-592-01 SCREW, +PSW M3X8
4-159-298-01 SCREW, +PSW M4X10
2-580-629-01 SCREW, +BVST 3×8

KDL-32/37/40/46/55EX500 Series(AEP/UK) 55
5-6. OTHER PARTS

5-6-1. ACCESSORIES and CONNECTORS

32 INCHES 46 INCHES
1-837-517-11 FLEXIBLE FLAT CABLE (CN2600-TCON) 1-837-523-11 FLEXIBLE FLAT CABLE (CN2600-TCON)
*1-910-060-06 HARNESS ASSY (CN2602,CN4300-CN001,SW,SP) *1-910-060-18 HARNESS ASSY (CN2602,CN4300-CN001,SW,SP)
*1-910-060-07 CONNECTOR ASSY 15P (CN6401-CN2561,CN3800) *1-910-060-19 CONNECTOR ASSY 15P (CN6150-CN2561,CN3800)
*1-910-060-08 CONNECTOR ASSY 14P (CN6402-BALANCER) *1-910-060-20 CONNECTOR ASSY 5P (CN6702-BALANCER)
*1-910-060-09 CONNECTOR ASSY 6P (CN6403-TCON) *1-910-060-21 CONNECTOR ASSY 6P (CN6151-TCON)

37 INCHES 55 INCHES
1-837-519-11 FLEXIBLE FLAT CABLE (CN2600-TCON) *1-836-742-11 CONNECTOR ASSY (CN6301-CN6600)
*1-910-060-10 HARNESS ASSY (CN2602,CN4300-CN001,SW,SP) *1-837-322-11 CONNECTOR ASSY (CN6705-BALANCER)
*1-910-060-11 CONNECTOR ASSY 15P (CN6401-CN2561,CN3800) *1-837-324-11 CONNECTOR ASSY (CN6704-BALANCER)
*1-910-060-12 CONNECTOR ASSY 14P (CN6402-BALANCER) 1-837-524-11 FLEXIBLE FLAT CABLE (CN6200-TCON)
*1-910-060-13 CONNECTOR ASSY 6P (CN6403-TCON) *1-910-060-22 HARNESS ASSY 15P (CN2602,CN3400-CN001,SW,SP)

40 INCHES *1-910-060-23 CONNECTOR ASSY 15P (CN6201-CN2561,CN3800)

1-837-521-11 FLEXIBLE FLAT CABLE (CN2600-TCON) *1-910-060-24 CONNECTOR ASSY 5P (CN6702-BALANCER)
*1-910-060-14 HARNESS ASSY (CN2602,CN4300-CN001,SW,SP) *1-910-060-25 CONNECTOR ASSY 6P (CN6403-TCON)
*1-910-060-15 CONNECTOR ASSY 15P (CN6401-CN2561,CN3800) *1-910-060-26 CONNECTOR ASSY 6P (CN6401-CN6703)
*1-910-060-16 CONNECTOR ASSY 14P (CN6402-BALANCER)
*1-910-060-17 CONNECTOR ASSY 6P (CN6403-TCON)

KDL-32/37/40/46/55EX500 Series(AEP/UK) 56
 5-6-2. INSTRUCTION MANUALS

*4-174-985-21 MANUAL, INSTRUCTION EX500,EX501,EX504

*4-174-985-31 MANUAL, INSTRUCTION EX500,EX501
*4-174-989-71 MANUAL, INSTRUCTION EX505,EX508
*4-174-990-11 MANUAL, INSTRUCTION EX503

5-6-3. REMOTE COMMANDER

1-487-700-11 REMOTE COMMANDER (RM-ED035)

1-487-758-11 REMOTE COMMANDER (RM-ED033) EX508

5-6-4. MISCELLANEOUS

1-822-482-11 HDMI CONNECTOR (REAR) 1-822-580-41 CONNECTOR DUAL SCART

1-822-484-11 HDMI CONNECTOR (SIDE) 1-822-581-12 MULTIPLE PHONO JACK 4P
1-822-525-21 OPTICAL OUT CONNECTOR 1-842-010-11 JACK
1-821-827-21 D SUB CONNECTOR 1-822-524-21 PHONO JACK 2P
1-821-868-11 ETHERNET CONNECTOR(8P) 1-842-096-11 PHONO JACK 5P

1-821-834-12 USB CONNECTOR

1-822-579-31 CARD CONNECTOR (PCMCIA CARD)

KDL-32/37/40/46/55EX500 Series(AEP/UK) 57
 END

English
Sony Corporation 11CP7100-1
Sony UK Made in U.K.
9-888-265-06 Service Promotions Dept. © 2011.03
KDL-32/37/40/46/55EX500 Series(AEP/UK) 58
 Hotel Assembly SOP For B2B Model

Use a Gauge to Pull the Wire (1-910-057-37) to Use Fingers to Pull Wire to the Outside
the Outside
*** Production line need to create pull gauge for operator use

Ready For Hotel Assembly – R2 Board Paste ID Label onto R/C First
 Hotel Assembly SOP For B2B Model

Fix VGA Screws (2-580-626-01) to Finished Assembly

R2 Board (A-1565-554-A)

Tilt, Angle Director to Bottom Cover Put R2 Board into bottom cover
 Hotel Assembly SOP For B2B Model

Press R2 Board into Bottom Cover Don’t Touch IR Pass-Through & Connector

Assembly Hole
Director Outside

Correct Align Hole Correct

 Hotel Assembly SOP For B2B Model
Assembly Hole Director Inside

Wrong Wrong Hole Not Aligned

Attention :
The Screws are
different to the
side cover & I/O

T3 Screw different to Side Cover Use & I/O Fix T3 Screw * 2 Pcs (14mm)To R/C
(Part Number 7-685-649-79)
 Hotel Assembly SOP For B2B Model

Insert Wire into R2 Board Fix Top Cover to Hotel Assy ( No

need to use a screw )

Finished
Hotel Assembly SOP For B2B Model - Separation

Push The Top Cover Edge

Finished Use finger to Pull the

Top Cover Edge