XP17 Manual

Table of Contents

1.Safety Precautions................................................................1
2.Introduction .............................................................................2
3.Installation ..............................................................................3
4.I/O Ports ...................................................................................4
5.Display Key Definition ........................................................5
6.OSD Menu ..........................................................................6
7.Timing Mode ..........................................................................8
8.Power Management ..............................................................9
9. Specifications..................................................................10
10.Easy Wall Mount ....................................................11
1. Safety Precautions:
Improper handing or care may damage the monitor. Please read the
following warnings carefully before installing the XP17 flat panel
display.
Warnings:
(1) Avoid placing the monitor or other heavy objects on the power
cord.

(2) Do not expose the monitor to rain, excessive moisture or dust.

(3) Do not cover the ventilation holes. Always place the monitor in an
open position where there is adequate ventilation.

(4) For best viewing avoid placing the monitor against a bright back
ground where sunlight or other light sources may reflect off the
face of the monitor. Place the monitor just below eye level.
(5) Handle with care during transportation.
(6) The LCD screen is delicate and easily damaged. Do not touch or
scratch the screen with your fingers.

Cleaning The Monitor:

(1) Disconnect the power cord before cleaning.
(2) Use the Screen Cleaning cloth to gently remove dust from the
screen.
(3) Apply a small quantity of alcohol to a soft cloth and wipe gently.
Do not use any other chemicals to clean the monitor.

Lit Pixels:
A lit pixel is defined as a single dot on the screen that is permanently
bright during operation. Such pixels do not effect the operation of the
LCD monitor and are no cause for concern. Lit pixels are the result of
the panel manufacturing procedure and are an inherent property of
LCD panels.

1
2. Introduction:
Thank you for purchasing the shuttle XP17 Flat Panel Display.
Before setting up and using the XP17, please read this manual
carefully, noting installation instructions and safety information.

Features:

1,280 x 1,024 (SXGA) display resolution.

31.5KHz to 80KHz horizontal scan and 56.3Hz to 75Hz vertical
scan.
Monitor preference settings and a complete spectrum of user adjust-
ments.
Tough, AG(Anti-Glare) tempered glass (>Moh’s Scale of Hardness 8)
facia.
Compact, sleek design matching the XPC's industrial design stan-
dards.

VESA DPMS power management compliant.

Three viewing angles: 30º / 45º / 60º adjustable stand.
Portrait view: 90º swivel stand.
VESA compliant wall mount support.

Caution:
Don’t set the back adjustible stand to less than 30º.

Accessories: Option Accessories:

Analog VGA D-Sub cable. PF50 Display to go(Optional).
Digital DVI cable. PF17 Zero degree Stand(Optional).
Power cable.
48 Watt power adapter.
User’s manual.
Screen Cleaning Cloth.
2
3. Installation:
(1) Turn off the PC and unplug the power cord.
(2) Using the supplied VGA (analog) or DVI (digital) cable, connect
one end to the PC VGA/DVI port and the other to the display’s
input ports. Tighten the thumbscrews.
(3) Plug in the 12V DC power jack from the supplied power adapter to
the 12V DC input socket on the Flat Panel Display.
(4) Turn on the flat panel display.
(5) Adjust the display preferences as required. See Chapter 6, OSD
menu for more information)

Caution:
Only use the supplied power adapter with this flat panel dis-
play. Using any other power adapter may damage the unit
and will invalidate the warranty.

3
4. I/O Ports:
12V DC in: Standardized DC input socket for supplying power to the
flat panel display.

D-Sub Input: Analog VGA input port.

DVI Input: Digital DVI input port.

Caution:
1. Connecting the DVI and the D-Sub cables at the same time will
result in the monitor running in analog mode.
2. To swap from Analog to Digital mode; Power down the PC. Discon-
nect the D-Sub cable and attach the DVI cable. Power on the PC .

4
5. Display Key Definition:

Reference
Name Function
Number
1 Power button Power on the display.

[1] Amber light indicates the monitor is in a low power state.

2 Status Indicator:
[2] Blue light or lit "Shuttle" logo indicates the panel is on.

[1] Launch and shutdown the OSD menu.

3 Menu Key:
[2] Return to the main OSD menu.

Scroll the OSD menu and adjust properties in a anti-clockwise

4 - Key
direction.

5 + Key Scroll the OSD menu and adjust properties in a clockwise direction.

[1] Select an option in the OSD menu.

6 Select Key:
[2] Execute an option.

Automatically adjusts the clock, phase, H-position and V-position

7 Auto adjust Key
values to optimal settings.

5
6.OSD Menu:

On-Screen Display Controls:

Icon Name Function Description

Auto Setup Automatically adjusts the display setup.
Press the key then use the + and - keys
to switch between yes and no. Press the
key to accept your selection.

Brightness Adjusts the brightness of the display. Press

the key then using + - keys darken or
lighten the background. Press the key
to return to the main menu.

Contrast Adjust the displays contrast level. Press

the key then using the + - keys in-
crease / decrease the contrast level. Press
the key to return to the main menu.

Language Language selection. Press the key

then using the + - keys to select the
desired OSD langage. Press the key to
return to the main menu.

H-V Position Shift the image on the screen horizontally /

vertically. Press the key then using the
+ - keys adjust the image on the screen
horizontally and vertically. Press the
key to return to the main menu.

Image Adjust Press the key then using the + - keys

scroll to the mode you wish to adjust,
Press the select key to start adjusting that
mode. Then press again.

Color Temp. Press the key then using the + - keys

select either 6500K / 9300K / User Mode.
Press the key to return to the previous
6 menu.
Phase adjust Press the key then using the + - keys
adjust the phase value of the image. Press
the key to return to the previous menu.

Clock adjust Press the key then using the + - keys

adjust the clock value of the image. Press
the key to return to the previous menu.

Sharpness Press the key then using the + - keys

adjust the sharpness of the image. Press
the key to return to the previous menu.

Information Scroll over this item to view Model No. H/V

Frequency and Resolution information.

Reset Select this item to revert to default (factory)

settings. Press the key to select this
item, then using the + - keys, select “yes”
or “No” followed by to execute.

Input select Press the key then using the + - keys

select either Analog or Digital mode. Press
the key to return to the main menu.

7
7. Timing Mode: * Preset
Horiz.F Vert.F Horiz.F Vert.F
Item Resolution Note Item Resolution Note
(KHz) (Hz) (KHz) (Hz)

1 1280 x 1024 80 75 VESA 15 1024 x 768 48 60 VESA

2 1280 x 1024 77 72 VESA 16 832 x 624 49 75 MAC

3 1280 x 1024 74 70 VESA 17 800 x 600 46 75 VESA

4 1280 x 1024 64 60 VESA 18 800 x 600 48 72 VESA

5 1280 x 960 60 60 VESA 19 800 x 600 43 70 VESA

6 1152 x 870 69 75 MAC 20 800 x 600 37 60 VESA

7 1152 x 864 67 75 VESA 21 720 x 400 31 70 VGA

8 1152 x 864 65 72 VESA 22 640 x 480 37 75 VESA

9 1152 x 864 63 70 VESA 23 640 x 480 37 72 VESA

10 1152 x 864 54 60 VESA 24 640 x 480 35 70 VESA

11 1024 x 768 60 75 VESA 25 640 x 480 35 66 MAC

12 1024 x 768 60 75 MAC 26 640 x 480 31 60 VESA

13 1024 x 768 58 72 VESA 27 640 x 350 31 70 IBM VGA

14 1024 x 768 56 70 VESA 28 640 x 350 60 IBM VGA

User Timing Mode Setup:

The default display frequency settings are displayed in the table above.
These settings have been optimized to provide the best display image
for a set resolution. You do not need to tamper with these settings. For
optimal adjustments to these settings, the user is recommended to run
the Auto setup feature in a Window's "Full Screen" environment.

8
8. Power Management:
This display is equipped with power management control to automati-
cally reduce the power consumption when the monitor is not in use.
The power managment feature has the following 4 modes:

State Hor. Sync Vert. Sync Power Consumption LCD Light

ON ON ON <40 Watts Logo white/ Blue

Standby OFF ON <5 Watts Amber

Suspend ON OFF <5 Watts Amber

OFF OFF OFF <3 Watts OFF

Data Display Channel (DDC):

To make installation easy, this monitor supports Plug and Play if your
PC supports DDC protocol. DDC is a communication protocol
through which the monitor can automatically communicate and inform
the host system (PC) about its capabilities, for example, supported
resolution and frequency settings. This display supports DDC1 and
DDC2 standards.

9
9. Specifications:
Display Features Size 17” TFT LCD
Power Input AC90 ~ 264 V, 50 ~ 60 Hz.
Display Area 338 mm x 270 mm.
Contrast Ratio 450:1
Viewing Angle (H)140 / (V)140 degrees
Operation Features Resolution SXGA 1280 x 1024 75Hz(Max)
Brightness 260 cd/m2
Response Time 16 ms
Interface Analog RGB / DVI
Connectors D-Sub / DVI
User’s Control Front Panel Control Power on/off, Menu,
-/+ Keys, Select, Auto.
Physical Specification Dimension 422.7mm x 434.5mm x 64mm
Net Weight 4.3 Kg
Power Power Saving VESA DMPS Standard.

Power Consumption Less than 40 Watts.

Note: Specifications provided above were the best available at time of

printing. These specifications are subject to change without notice.
For more information, please contact your local authorized Shuttle
dealer.

10
10. Easy Wall Mount:
Step 1:
Slide a screwdriver into the
slot on the back cover.
Twist gently to loosen.

Step 2:
Remove the back cover.

Step 3:
Using a screwdriver, remove
the exposed screws.

11
 Step 4:
Remove the protective cover.

Step 5:
Unfasten the four hinge
screws.

Step 6:
Remove the hinge.

12
 Step 7:
Attach the wall mount
bracket to the back of LCD
monitor.

NOTE: This display can be mounted on a wall using a VESA

compatible 100mm x 100mm arm/or wall bracket. See your
local authorized Shuttle dealer for information on where to
purchase such brackets.

Step 8: Installating a
VESA bracket.

1. Select an appropri-
ate VESA compatible
bracket, such as the
one pictured here.

13
 2. Attach the display
portion of the mounting
bracket to the display as
shown.

3. Attach the wall

portion of the mounting
bracket to the wall as
shown. Take care to
firmly attach the mount-
ing bracket level and
flush to the wall.

14
 4. Attach the two
sections of the mount-
ing bracket, making
sure the attachment is
firm and secure.

Note: Shuttle provides no warranty over VESA mounting devices. This

wall mounting demonstration is provided for users information only.
Please read the instructions that come with your mounting bracket
before installing any mounting bracket to the display unit.

15