Scribd
Upload
82 views

Friction Drag Coefficient For Steady, Constant Property, 2-D, Uniform Flow Over A Flat Plate

The document discusses drag coefficient formulas for different flow regimes over a flat plate: 1) Laminar flow has a drag coefficient of CDf = 1.328 Rel−1/2 where Rel is the Reynolds number. 2) Mixed or transitional flow has two drag coefficient formulas depending on the Reynolds number range. 3) Turbulent flow over a smooth plate and completely turbulent flow both have drag coefficient formulas involving the Reynolds number and plate roughness. The drag coefficient is used to characterize drag force due to friction and depends on factors like the Reynolds number, flow regime, and surface roughness.

Uploaded by

Yuza Rahmadhan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
82 views

Friction Drag Coefficient For Steady, Constant Property, 2-D, Uniform Flow Over A Flat Plate

The document discusses drag coefficient formulas for different flow regimes over a flat plate: 1) Laminar flow has a drag coefficient of CDf = 1.328 Rel−1/2 where Rel is the Reynolds number. 2) Mixed or transitional flow has two drag coefficient formulas depending on the Reynolds number range. 3) Turbulent flow over a smooth plate and completely turbulent flow both have drag coefficient formulas involving the Reynolds number and plate roughness. The drag coefficient is used to characterize drag force due to friction and depends on factors like the Reynolds number, flow regime, and surface roughness.

Uploaded by

Yuza Rahmadhan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Friction drag coefficient for steady, constant property, 2-D, uniform flow over a flat plate:

Laminar: CDf = 1.328 Reℓ−1/2 Reℓ < 5 × 105

1740
Mixed or Transitional: CDf = 0.0743 Reℓ−1/5 − 5 ×10 5 < Reℓ < 10 7
Reℓ €
€
0.455 1700
CDf = 2.58 − 5 ×10 5 < Reℓ < 10 9
(log Reℓ ) Reℓ
€

Turbulent (smooth plate): CDf = 0.0743 Reℓ−1/5 5 ×10 5 < Reℓ < 10 7
€
0.455
CDf = 2.58 5 ×10 5 < Reℓ < 10 9
€ (log Reℓ )
−2.5
⎡ ⎛ ε ⎞⎤
Turbulent (completely turbulent): CDf = ⎢1.89 −1.62 log ⎜ ⎟⎥ see Table 8.1 for ε
€ ⎣ ⎝ ℓ ⎠⎦

where Reℓ = U ℓ ν is Reynolds number, U is free stream velocity, ν is kinematic viscosity, ℓ is


plate length, b is plate width, ε is plate roughness, and D f is drag force due to friction.
€

€ €
€
ℓ

Reℓ = U ℓ ν

€
Streamlines for cylinder in uniform cross flow for a range of Reynolds numbers.

D
CD = 1
2 ρ U 2 Ap

Drag coefficient, CD, versus Reynolds number, Re, where D is total drag, U is uniform
velocity, D is diameter, Ap is projected frontal area, ρ is density, and µ is viscosity.
Strong differences in laminar and turbulent separation on an 8.5-in. bowling ball entering water
at 25 ft/s: (a) smooth ball, laminar boundary layer; (b) same entry, turbulent flow induced by
patch of nose-sand roughness (NAVAIR Weapons Division Historical Archives.)

CD = 0.12
CD = 1.2

Two objects of considerably different size that have the same drag force.

Drag coefficient as a function of Froude number and hull characteristics for that portion of the
drag due to the generation of waves (Inui, Wave Making Resistance of Ships, 1962).
Effect of angle of attack, α , and aspect ratio, A = b/c where b is span and c is chord length,
on lift coefficient, CL, and drag coefficient, CD, for typical airfoils.

α = 0˚ stall at high α

Wing with trailing vortices.


(a) uniform flow (b) free vortex at (c) uniform flow past
past a cylinder center of cylinder rotating cylinder

Rotating cylinder
with separation

D
Lift coefficient, CL, and drag coefficient,
CD, versus spin ratio, SR = (ω D) (2 U ) ,
for a spinning smooth sphere where:

ω rate of rotation
D €
diameter
U uniform velocity
Re Reynolds number
ρ density
L
ν kinematic viscosity
D drag
L lift

You might also like