LABORATORY: ELECTRONICS AND MODERN INSTRUMENTATION:

Unit 1: Introduction to Basic Electronic Components. Test and

Measurement Instruments

Introduction

In the designing of any electronic circuit, three most important considerations are:

(i) Circuit components like resistors, Capacitors, Transistors and Diodes.

(ii) Power sources like dc power supplies and signal generators

(iii) Measurement and analysis instruments like multimeters and Cathode Ray

Oscilloscope (CRO).

This Unit deals with familiarization of basic components like resistors, Capacitors and diodes,

followed by introduction to a few instruments like multimetrs and CRO. At the end a few

experiments related with CRO have been explained.

Basic Components: Basic components like capacitors, resistors, inductors, diodes, light

emitting diode (led) and transistors can be divided into 2 categories: (i) Passive components like

resistors and capacitors and (ii) Active components like diodes and transistors. The difference

between the above two categories is that active components can generate energy whereas passive

components can not generate energy. In other words active components can increase power of a

signal whereas passive components often cause the power to be lost.

Some components like resistors have their values marked on them whereas others like

transistors do not have any value marking but have a type number on them. One has to refer to

datasheets to get to know the value of the unmarked component. Besides component values, they

are also characterized by their ratings for e.g. maximum current value that a component can

stand without being burnt out.

1
Resistors: Resistors can be of two types: fixed value resistors or variable resistors. The

formula for resistance is given by: R = ρ l / A where ρ is resistivity, l is length and A is area of

crossection. Different value resistors can be manufactured by changing the length and area of

crossection or the material itself which changes the resistivity. Materials generally used for

fabrication of resistors are nichrome (80 % Ni and 20 % Cr), constatntan (55% cu and 45 %

Ni ) and Manmganin (85 % Cu and 10 % Mn and < 5 % Ni). Metals are not used as they have a

very high temperature coefficient of resistance. Three main methods of fabrication are (i) a slab

or a rod of suitable resistivity, (ii) Material using thinner crossection and longer length. The

length is doubled and then wound in such a way that inductance effects are cancelled out. (iii)

Thin films of material on insulating substrate. Each resistor has a current carrying capacity.

Current more than the prescribed wattage may damage the resistor.

Colour Code for Resistors

Band colour Band colour & its

& its value tolerance

Black = 0 Gold = + - 5%
Brown = 1 Silver = + - 10 %
Red = 2 No colour means 20 %
Orange = 3
Yellow = 4
Green = 5
Blue = 6
Violet = 7
Grey = 8
White = 9

2
The first two bands near an end indicate first 2 digits, digit corresponding to 3rd band is the

power of 10 to be multiplied and fourth band indicates tolerance as mentioned in the table. Refer

fig 1, where brown = 1, black = 0, red = 2 and silver = 10 % tolerance. Hence its value is

10 x 10 2 Ω = 1 k Ω.

Most commonly used resistors in lab are fixed value resistors which exist for standard values

according to E12. Other ranges are E24 and E48 Ranges.

E12 Range: Table 1 is for the values of resistors of E12 range. Topmost row defines the basic

value units of resistors in ohms. Every following row is 10 fold of the upper row.

Table 1: Table for E12 range values of resistors.

1.0 Ω 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 Ω
10 Ω 12 . . . . 68 82 Ω
100 Ω 680 820 Ω
1k 1.2k 6.8k 8.2k
10k 82k
100k 820k
1M 1.2M 6.8M` 8.2M
10M 12M 68M 82M

Variable resistors Besides the fixed value resistors, there also exist variable resistors. The

resistance of variable resistors can vary in steps or continuously. Potentiometer is also an

example of continuously varying resistor

3
Special purpose resistors Light dependent resistors (LDR) and thermistors are examples of

special purpose resistors. Thermistor is a resistor whose value depends on its temperature. It is

also called a heat sensor. LDR is a resistance whose resistance depends upon the amount of

light falling on it.

Capacitors

Capacitors are capable of storing charges. They are used for coupling ac signals from one circuit

to another and for frequency selection etc. A capacitor consists of 2 metallic plates separated by a

dielectric. The capacitance is defined as : C = Є o Єr A / d, where A is the area of plates, d is

plates separation, Єo is permittivity of free space and Є r is relative permittivity. An important

parameter for capacitors is its voltage handling capacity beyond which the capacitor dielectric

breaks down.

The value of a capacitor depends upon the dielectric constant (K = Є o Єr.) of the material. There

are three main classes of capacitors: (i) Non electrolytic or normal capacitors and (ii) electrolytic

capacitors and (iii) variable capacitors. Normal capacitors are mostly of parallel plate type and

can have mica, paper, ceramic or polymer as dielectric. In the paper capacitors two rectangular

metal foils are interleaved between thin sheets of waxed paper and the whole system is rolled to

form a compact structure. Each metal foil is connected to an electrode. In mica capacitors

alternate layers of mica and metal are clamped tightly together. Refer fig 3.

In electrolytic capacitor mostly a then metal-oxide film is deposited by means of electrolysis on

axial electrode. That’s how it derives its name. During electrolysis the electrode acts as anode

whose cathode is a concentric can. Since the dielectric layer is very thin hence these require

special precaution for their use: i.e. they have to connected in the right polarity failing which the

dielectric breaks down. Besides these fixed value capacitors we also have variable capacitors

whose value depends upon the area of crossection. They have a fixed set of plates and a movable

4
set of plates which can be moved through a shaft. This movement changes the area of overlap of

the two sets of plates which changes its capacity. Refer fig 3.

Colour and Number code of capacitors. Different marking schemes are used for electrolytic and

non-electrolytic capacitors. Temperature coefficient is of minor importance in an electrolytic

filter capacitor, but it is very important in ceramic trimmers for attenuator use. One never finds

temperature coefficient on an electrolytic label, but it is always present on ceramic trimmers.

(i) Electrolytic Capacitors: There are two designs of electrolytic capacitors: (i) Axial

where the leads are attached to each end (220µF in picture) and (ii) Radial where

both leads are at the same end (10µF in picture) Refer fig 4.

5
(iii) Non-polarised capacitors ( < 1µF): Small value capacitors have their values printed but

without a multiplier. For example 0.1 means 0.1µF = 100nF. Sometimes the unit is placed in

between 2 digits indicating a decimal point. For example: 4n7 means 4.7nF.

Capacitor Number Code : A number code is often used on small capacitors where printing is

difficult: the 1st number is the 1st digit, the 2nd number is the 2nd digit, the 3rd number is the

power of ten to be multiplied., to give the capacitance in pF. Any letters just indicate tolerance

and voltage rating. For example: 102 means 10 X 10 2 pF = 1nF and 472J means 4700pF =

4.7nF (J means 5% tolerance).

Capacitor Colour Code: Sometimes capacitors just show bands like resistors when printing

is tough on them. The colours should be read like the resistor code, the top three colour bands

6
giving the value in pF. The 4th band and 5th band are for tolerance and voltage rating

respectively. For example: brown, black, orange means 10000pF = 10nF = 0.01µF.

Available Values of Capacitors: Like resistors capacitors are also available for only

particular values. Following are 2 series defined for capacitors

The E3 series (3 values for each multiple of ten) 10, 22, 47, then it continues 1to100, 220, 470,

1000, 2200, 4700, 10000 etc.

The E6 series (6 values for each multiple of ten) 10, 15, 22, 33, 47, 68, ... then it continues 100,

150, 220, 330, 470, 680, 1000 etc.

Inductors: Inductor is a component made by a coil of wire which is wound on a core. It is

used to vary the impedance of a circuit or for frequency tuning. The value of an inductor depends

upon the total number of turns (N), area of crossection of the core (A) and length of the core

(l).The formula is L = μo μr N2 A / l. Its unit is in Henry.

Diode: A diode is a single junction device made of p and n type materials.. Its main function is to

rectify an ac signal although other special purpose diodes like zener and led’s are used for other

purposes. A normal diode comes in a black casing whereas a zener diode has a transparent

casing. Their pictures and symbols are given in fig. 7.

7
Other diodes may be made by a p type and n type materials or between a semiconductor and a

metal. If the junction is made between a metal and semiconductor then it is called a Schottky

diode whose application is in rectifying and non-rectifying contacts and Schottky devices. If the

pn junction is made between very heavily doped materials then it forms a Zener diode. These are

used for voltage regulation in power supplies. and have breakdown voltages which are very low.

The normal diode has a breakdown voltage of greater than 100 V.

Some of the diode specifications are: Maximum reverse voltage (V br), rated forward current (If) ,

maximum forward voltage drop (Vf) and package style. Table 3 gives some of the most

commonly used diodes with their specifications.

Table 3

Device Material IF (mA) VF(V) VBR

Number used. (V)

OA91 Ge 50 2.1 115
In 4148 Si 100 1.0 75
In 4149 Si 100 1.0 75
IN 4007 Si 1000 1.6 1000

To test whether a given diode is O.K. or not, a simple multimter test can be performed which is

given later in this unit.

8
Light Emitting Diode (LED)

Led’sare pn junction devices which emit light radiation when biased in the forward direction.

The semiconductor material used for these junctions is a compound semiconductor like AlGaAs

whose band gap corresponds to a particular wavelength according to equation E g = 1.24 / λ

where Eg is the band gap in ev and λ is the wavelength in microns. (e.g. red ~ 0.7 μ hence

corresponding E g = 1.24 / 0.7 = 1.77 ev). When the pn junction is forward biased, the electrons

are excited to conduction band and when they fall to the valence band, they give out energy in

the form of radiation corresponding to the Eg of the material Conventional led’s are made from

the materials like AlGaAs, GaAlP, GaAsP, GaP and GaN which emit Red, green, orange, yellow

and blue colours respectively. Led’s come in a special transparent casing as shown in fig 8..Dual

colour led’s are also available where two junctions are encapsulated on the same chip. It has

three leads where cathode is common whereas normal leds’ have two leads one for cathode and

other for anode. A very important precaution while using an led is the amount of current being

passed through it. For most leds the maximum allowable current is 20 mA beyond which the led

can burn out. Hence in most of the circuits a resistor is used to limit the current. Some important

specifications before using an led are: LED colour, peak wavelength, viewing angle, optical

power output, luminous intensity, forward current and forward voltage.

9
Transistors

Transistors are semiconductor devices used for applications like amplification of voltages,

current and are also used in oscillator circuits and switches. It’s a two junction and 3 terminal

device made of three layers of n and p type materials. The three regions are emitter, base and

collector. They are of 2 types (i) pnp and (ii) npn. Their most important specifications are Ic,

Vce, hfe and Power rating. They come in different casings like TO18, TO92C, and TO39 etc

Given below is a table of most commonly used transistors with their specifications (approximate)

and casings. Datasheets from the companies can be referred to to know the exact specifications.

Case IC VCE hFE Ptot Category Possible

Code Structure
style max. max. min. max. (typical use) substitutes
BC107 NPN TO18 100mA 45V 110 300mW Audio, low power BC182 BC547
General purpose, BC108C BC183
BC108 NPN TO18 100mA 20V 110 300mW
low power BC548
General purpose,
BC108C NPN TO18 100mA 20V 420 600mW
low power
Audio (low noise),
BC109 NPN TO18 200mA 20V 200 300mW BC184 BC549
low power
General purpose,
BC182 NPN TO92C 100mA 50V 100 350mW BC107 BC182L
low power

10
 General purpose,
BC182L NPN TO92A 100mA 50V 100 350mW BC107 BC182
low power
BC547B NPN TO92C 100mA 45V 200 500mW Audio, low power BC107B
General purpose,
BC548B NPN TO92C 100mA 30V 220 500mW BC108B
low power
Audio (low noise),
BC549B NPN TO92C 100mA 30V 240 625mW BC109
low power
General purpose,
2N3053 NPN TO39 700mA 40V 50 500mW BFY51
low power
General purpose,
BFY51 NPN TO39 1A 30V 40 800mW BC639
medium power
General purpose,
BC639 NPN TO92A 1A 80V 40 800mW BFY51
medium power
General purpose,
TIP29A NPN TO220 1A 60V 40 30W
high power
General purpose,
TIP31A NPN TO220 3A 60V 10 40W TIP31C TIP41A
high power
General purpose,
TIP31C NPN TO220 3A 100V 10 40W TIP31A TIP41A
high power
General purpose,
TIP41A NPN TO220 6A 60V 15 65W
high power
General purpose,
2N3055 NPN TO3 15A 60V 20 117W
high power
BC177 PNP TO18 100mA 45V 125 300mW Audio, low power BC477
General purpose,
BC178 PNP TO18 200mA 25V 120 600mW BC478
low power
Audio (low noise),
BC179 PNP TO18 200mA 20V 180 600mW
low power
BC477 PNP TO18 150mA 80V 125 360mW Audio, low power BC177
General purpose,
BC478 PNP TO18 150mA 40V 125 360mW BC178
low power
General purpose,
TIP32A PNP TO220 3A 60V 25 40W TIP32C
high power
General purpose,
TIP32C PNP TO220 3A 100V 10 40W TIP32A
high power

Fig 9 gives some of the transistors with the symbols. for npn and pnp. and fig 10 illustrates some

of the casings. with the configurations for emitter , base and collector leads

11
Integrated Circuits (IC)

Integrated Circuit (IC) Today all electrical, electronic and computer parts have IC’s in

them. Integrated circuit is a name given to a package which can hold more than 10 and up to

millions of electronic components. They can give various functions like : (i) the function of a full

12
microprocessor circuit (eg 8085), (ii) a memory chip, (iii) a voltage regulator (LM 7805) or (iv)

Can contain just 10 AND gates (eg LS7400). They come in a black bench like casing with a

notch on one side and with electrical legs for connections, which are called pins. The size is

usually around 1 cm2 X 1 cm2. Refer to the picture. Its name is always written on top which

contains a few letters with numerals, according to its type, make and company. For example an

IC with name LS 7400 would mean LS series with And gates, LM741C - mA741C is an

operational amplifier (opamp). Datasheets can be referred to, to know the details of pin

configurations and make etc. The pins are usually read starting from left of notch and going

anticlockwise as shown in picture for 555 timer IC.

Fabrication of an IC is a highly sophisticated and expensive process requiring clean rooms and

very expensive equipments like photolithography, metallization and diffusion etc. But because of

their bulk manufacture and requirement the cost of each IC is very low.

Instruments:

Multimeters: A multimeter is an instrument which measures electrical parameters such as AC or

DC voltage, current, and resistance. Rather than having separate meters, a multimeter combines a

13
voltmeter, an ammeter, and an ohmmeter. The two main kinds of a multimeter are analog and

digital. Refer fig 10. A digital multimeter has an LCD screen that displays the value of the

parameter being measured. while in an analog multimeter display, a needle moves through a

graduated scale. Topmost scale is usually for resistance and the readings increases from right to

left while other scales readings increase from left to right. Another name for an analog

multimeter is Volt-Ohm-Milliammeter (VOM). Each type of meter has its advantages and

disadvantaged. When used as a voltmeter, a digital meter is usually better because its resistance

is much higher, 1 M or 10 M, compared to 200 Ω for an analogue multimeter for a similar range.

On the other hand, it is easier to follow a slowly changing voltage by watching the needle on an

analogue display. Most modern multimeters are digital and traditional analogue types are

becoming obsolete

Block diagram of a VOM is given in fig. 11

14
Voltage measurement by multimeter: For the case of a VOM, a zero adjustment has to be

made every time the multimeter is to be used. To do the zero adjustment, set the mode selection

knob in resistance mode. Connect the two leads to positive and common terminals respectively

and short the leads. The needle should move to extreme right to the last reading on the ohms

scale. If it stops before or goes beyond then the zero adjustment knob has to be rotated

(clockwise or anticlockwise) such that the needle rests at the last reading on the right end of the

bar on the ohms scale. Subsequently, to measure voltage, the multimeter has to be first set in AC

or DC mode. After selecting a suitable range defined by the uppermost limit of the expected

value, the range knob has to be set. Next connect the common (gnd) terminal through a lead

(black) to the gnd of the circuit and the red lead to the point where voltage is to be measured. For

the case of an analogue multimeter, if the needle goes the wrong way the leads have to be

reversed or if the needle doesn’t move at all the range has to be changed. To find the value of the

voltage, read the number from that scale that matches the range being used. In a digital

multimeter, if 1. is displayed then the range has to be increased..

15
Resistance Measurement: To measure resistance in a circuit, first the power supply is to be

turned off (or disconnected) otherwise the multimeter might get damaged. Next, select a range on

the multimeter and touch two metal points in the circuit. If the needle doesn’t move or goes all

the way to the end of the scale, select another range. One can not use this method to measure the

resistance of a resistor in the circuit because there may be other paths between the nodes of a

resistor. One leg of a resistor must be disconnected from the circuit to make sure that the only

path between the two probes is through that resistor. To measure the resistance of a resistor,

select the range on the meter that might be closest to the right value and use the probes to touch

either side of the resistor. If the right range is selected then the needle will be somewhere

between the left and the right end of the scale. To find the value of the resistor, read the number

from the scale that matches the range you are using.

MULTIMETER TEST OF DIODES

One can know whether a specific terminal of a diode is n or p by measuring the resistance with

multimeter. To do so keep the multimeters in resistance mode connect its positive lead to the

anode of diode and negative lead to its cathode. During the test, the multimeter passes current

through the diode and the diode gets forward biased. It thus indicated very low resistance of the

order of 100  . If the leads are now reversed than the diode gets reverse biased and offers very

high resistance of the order of M. This can be read in the multimeter again. If a diode reads

very low resistance in the forward as well as reverse bias then it is shorted. On the other hand if

it reads high resistance in the forward as well as reverse bias then it is open.

FUNCTION GENERATORS

16
Function Generators are instruments capable of generating an ac signal of any frequency (~

100Hz – hundreds of kHz), voltage(~1 mv – 20V) and various forms (e.g. sine wave, Square

pulse, Saw tooth wave, Triangular wave or noise waveform). They also provide a continuously

variable dc offset, variable duty cycle. They are usually of 2 types: (i) analog and (ii) Digital.

Some of the front panel controls of a typical function generator are:

1 Power Switch For switching obn the power supply

2 Digital Display This is a 4 digit frequency meter

3 OFFSET This knob is for adding a dc voltage to the output signal

4 Amplitude This does the continuous adjustment of output voltage

17
5 Speed This is for setting wobulation speed

6 Width This knob is for setting the wobulation width

7 Frquency This knob is for selecting the frequency range from 0.3 Hz to 3MHz in

decade steps.

8. Sweep On This is a push button for activating internal sweep

9 Mode Selection Push Button for triangular, sine Square etc.

10 BNC connector This is a 50 Ω output BNC connector

11 -20 db, - 20 dbA push button control for -20 db attenuation. When both buttons are

pushed then a total of 40 db attenuation is got.

Cathode Ray Oscilloscope (CRO)

CRO is an instrument which is used to measure voltages that change with time and to display the

waveforms in real time mode. There is a graphical scale present on the screen which is used to

calculate the voltage or frequency value. A very important specification of a CRO is its

bandwidth which gives the maximum frequency of a signal which a CRO can measure. A simple

oscilloscope consists of a cathode ray tube, a vertical amplifier, a time base, a horizontal

amplifier and a power supply. Fig 12 shows the block diagram of a CRO. Cathode-ray tube is a

vacuum tube in which a beam of electrons is produced and focused onto a fluorescent screen.

The electrons’ kinetic energy is converted into light energy as they collide with the screen. It is

an essential component of television receivers, computer visual display units, and CRO. Between

18
the electron gun and the screen are two pairs of metal plates : (i) Horizontal Deflection Plates

and (ii) Vertical deflection plates. These are driven by Horizontal Deflection system and Vertical

deflection system respectively.

In

the vertical deflection system, the vertical amplifier is driven by an external voltage (the vertical

input) that is to be measured. The amplifier has very high input impedance, typically one

megohm, so that it draws only a tiny current from the signal source. The amplifier drives the

vertical deflection plates with a voltage that is proportional to the vertical input. The gain of the

vertical amplifier can be adjusted to suit the amplitude of the input voltage. A positive input

voltage bends the electron beam upwards, and a negative voltage bends it downwards, so that the

vertical deflection of the dot shows the value of the input. The horizontal deflection system

19
consists of a time base circuit which is an electronic circuit that generates a ramp voltage (saw

tooth waveform) . Refer fig. 13.

This is a voltage that changes continuously and linearly

with time. When it reaches a predefined value the ramp is reset. When a trigger event is

recognized the reset is released, allowing the ramp to increase again. The time base voltage

usually drives the horizontal amplifier. Its effect is to sweep the electron beam at a constant

speed from left to right across the screen, then quickly return the beam to the left in time to begin

the next sweep.

CRO controls from the front panel

20
1 Intensity This knob controls the brightness of the trace by adjusting the number of

electrons emerging from the gun

2 Focus This control is for making the trace on the screen sharper. It is connected

to the anode of the electron gun whose voltage collimates the electron beam.

3 Vertical Position & Horizontal Position Through these controls the beam can be

positioned at variable vertical or horizontal positions as desired. These knobs apply a dc voltage

to the vertical and horizontal deflection plates.

4 V / Div. This control is used to control the voltage sensitivity. This is internally

connected to an attenuator of the vertical system. It determines the voltage required by the

vertical plates to deflect the beam vertically by one division.

21
5 Time / Div This determines the time taken for the spot to move horizontally across

one division of the screen when the sweep is generated by triggering process. The signal which is

fed to the vertical deflection plates provides the triggering to the waveform. Each position of the

time/ div knob is applicable for a particular frequency. This determines the horizontal sensitivity

of the observed signal.

6 Trigger SourceThis selects the source of the trigger to be applied to the saw tooth

waveform. There are usually three possible sources (i) Internal: This is mostly used for all

applications. The vertical signal applies the triggering signal. (ii) Line: This is generally used

when the voltage to be measured is related to the line voltage. This selects the 50Hz line voltage.

(iii) Ext. In this case an external signal is applied to trigger the saw tooth waveform./

7 Slope This determines whether the time base circuit responds to the positive or negative

slope of the triggering waveform.

8 Level This determines the amplitude level on the triggering waveform which can

start the sweep

9 AC, DC, GND: This selects the coupling mechanism for the input signal to the

CRO. In dc mode the vertical amplifier receives both ac and dc components of the input signal.

In ac mode the coupling capacitor blocks all dc components and displays only pure ac waveform.

In gnd configuration, the input signal is grounded and one gets a straight line. To measure the dc

component of any signal (ac or dc), one has to switch from ac to dc mode and observe the

vertical shift of the waveform. The amount of vertical shift in volts gives the corresponding dc

component.

22
10 X-Y mode: In this mode of operation. two signals are superimposed at right angles on

each other. The saw tooth time base circuit is disconnected from the horizontal deflection plates

and the external signal which s fed to channel two is given to time base instead. Hence if two

sine waves are fed to two channels respectively then the electron beam will undergo deflection

according to right angle superposition of two sine waves. It will trace lissajous figures.

Few experiments related with CRO:

Objective To measure voltage and frequency of an ac signal

Voltage measurement To measure the voltage of an ac waveform, connect the ac signal

from signal generator to CRO channel 1 such that a stable waveform such as that of fig 14. is

displayed. Here Vpp is the peak to peak voltage and Vm is the maximum voltage.

23
Suppose volts / div is at 1V scale then Vpp = 4 div x 1 V = 4V

and Vm = 2div x 1V = 2V.

The effective value is V effec = V rms= Vm X 0.7. = 1.4 V

If an ac voltmeter is connected across the signal it will give the same value i.e.1.4V.

Frequency Measurement The distance covered by one wave in fig. 14 , gives the time period

(T) of the waveform.

Suppose time / div knob is at 1 ms scale then T = 2div x 1 ms = 2 msec.

Hence frequency (F) = 1 / T = 1 / 2msec = 0.5 kHz = 500 Hz.

Objective To measure frequency ratio and measure phase difference of 2 waveforms using

lissajous figures.

Lissajous Figures

24
When a particle is influenced by two simple harmonic motions which are at right angles to each

other then it traces a curve called lissajous figure. For the case of a CRO, when the time base of

the CRO is not applied to the horizontal (X) plates, any waveform can be applied across these

plates. If different sine waves are applied to the X and Y plates, a stationary pattern is traced by

the electron beam. This pattern depends on the ratio of the frequencies of the two waves ( i.e. 1:

1, 1:2, 1:3 or 1:4 etc.) and the phase difference between the two waves. The frequency ratio of

1:1 gives a circular pattern if the signals (i) have the same amplitudes and (ii) are 90 out of

phase. A phase difference of 45o produces an ellipse, and zero phase difference produces a

straight line inclined at an angle determined by the magnitudes of the two signals.

Measurement of Frequency Ratio

For measurement of frequency ratio refer to circuit of fig. 15 , where two sine waves are applied

to the two channels and Oscilloscope is kept in X-Y mode

25
The frequency ratio is determined by the number of loops of the pattern touching a vertical line

at the edge of the pattern and the number of loops touching a horizontal line at the edge of the

pattern. The reason for this is that an integral number of sine waves on the horizontal deflection

plates are completed in the same time that an integral number of sine waves are completed on the

vertical plates. If Tv and Th are the time periods of vertical and horizontal input sine waves

respectively then

TV Number of loops touching vertical line fH 2

  
TH Number of loops touching horizontal line fV 1

where fH and fV are the frequencies of horizontal and vertical signals respectively. In fig. 16 ,

lissajous figures for various frequency ratios are drawn.

26
Measurement of Phase Difference

For measurement of Phase difference between 2 waves, connect the circuit as in fig. 17 .and

operate the CRO in X-Y mode.

27
The phase difference is determined by measuring ratio of the maximum Y intercept to the

intercept made on Y axis. Refer Fig 18, where Y 1 is the maximum Y intercept and Y2 is the

intercept on Y axis. Hence if Phase difference between the 2 waves is Φ, then

Sin Φ = Y2 / Y1. Therefore Φ = Sin-1 Y2 / Y1

28
Figure 19 illustrates some more patterns of lissajous figures for various values of phase

differences.

References

1. Electronic Instrumentation and Measuremenmt Techniques, 3rd Edition, by

W.D.Cooper and A.D. Helfrick, PHI

2. http://acept.la.asu.edu/courses/phs110/expmts/exp13a.html

29