SCP250 VAR/Power Factor Controller

Class 200 Equipment

SCP250
VAR/Power Factor
Controller

The SCP 250 senses generator output voltage and current, provides an output
signal that is electronically injected into the voltage regulator. When VARs are
controlled, the voltage regulator (or static exciter) changes its output until the
programmed reactive load current is attained. When power factor is controlled,
the regulator changes the excitation until the selected power factor is obtained.
The unit is designed so that the voltage regulator is in total control of generator
excitation until the generator breaker is closed. At breaker closure the SCP 250
assumes excitation control.

The SCP 250 also contains a voltage limiting feature so that in the event utility
power is lost and the peaking generator main breaker remains closed, the
voltage regulator will not go to full or no excitation. Voltage limiting is adjustable
APPLICATIONS
between ±10% and ±30% Because the unit is designed for behind-the-panel Page 2
mounting, provisions are included for remotely locating the VAR/PF switch and
VAR/PF adjust potentiometer.

FEATURES SPECIFICATIONS
Page 2
• Specifically designed to operate with the standard Basler SR, KR, selected AVCs,
and SSR regulator series and with Basler SSE static exciter-regulators.
• Front Panel Selection of either VAR or power factor control.
• With P.F. control, reactive load changes automatically when KW load is changed.
• Models suitable for use in generator or synchronous motor applications. INTERCONNECTION
• Solid-state design. DIAGRAMS
• Does not require use of motor operated control. Page 3
• Responds rapidly to system changes.
• Provides system control over wide range of loading conditions.
• Easily calibrated on-site OUTLINE DRAWING
• Accommodates standard voltage sensing inputs. Page 4
• Provisions for remote operation.
• Mechanically rugged and compact.
• UL recognized and CSA certified.

ADDITIONAL INFORMATION
INSTRUCTION MANUAL
Request publication 911000099Y

UKR-7
9-03
P. O. BOX 269 HIGHLAND, ILLINOIS, U.S.A. 62249 PHONE 618-654-2341 FAX 618-654-2351
SCP250 VAR/Power Factor Controller

APPLICATION SPECIFICATIONS
GENERATOR PEAKING • INPUT POWER:
On peaking generator applications, the paralleling Voltage Sensing and Power
circuit of a voltage regulator presents large changes in Voltage:
reactive current when the bus voltage changes by a 120-139.208-240.416-480. 520-600 VAC, ±10%, 60Hz
relatively small amount. However, the regulator’s ability 100-120, 190-208,380-415,440-500 VAC, 10%, 50Hz
to compensate for large changes in bus voltage can be Phase : Single
exceeded. Two examples serve to illustrate typical Burden: 25 VA
problem areas: Current Sensing
(1) A generator equipped with a voltage regulator Current:
adjusted for 4% droop can have a variation in VAR 3-5 Amperes, withstands up to 30 amps for 15 sec.
(volt amperes reactive) load from 0 to 100% with a without failure.
4% decrease in bus voltage. Further decreases in Phase : Single
bus voltage would overload the generator. Burden: 3VA
(2) An increase in bus voltage can cause leading • OUTPUT: Normal ±1VDC to ±3VDC
power factor conditions with the associated danger High ±1VDC to ±9VDC
of the machine pulling out of synchronization. • OUTPUT VOLTAGE LIMITING: Adjusts range of
output voltage over range shown above.
To minimize the possibility of either (1) or (2) above • ACCURACY OF CONTROL:
occurring, the voltage regulator is often adjusted for Power Factor: Reactive component of current is
operation in a “safe” region rather than a region that proportional to real component within ±5% of
utilizes the full KVA capability of the generator. maximum rated current.
VAR: Reactive component of current maintained at
The SCP 250 VAR/Power Factor Controller regulates programmed level within 25% of maximum
VAR flow or power factor when operating in parallel with rated
another power system. The excitation is adjusted current.
automatically to compensate for bus voltage changes. • TEMPERATURE: Operates within temperature range
A typical peaking application is illustrated in Figure 1. of -40°C (-40°F) to +70°C (+158°F).
• VIBRATION: Withstands 1.3 Gs from 5 to 26Hz, .036
The SCP 250 is not for use on single or multiple paral- D.A. from 26 to 51Hz, and 5 Gs from 52 to 260Hz
leled generators except when paralleled to an infinite without damage or degradation of performance.
grid source. When not paralleled to a utility bus, use • SHOCK: Withstands 15 Gs in each of three mutually
Basler regulators with reactive compensation provisions perpendicular axes.
for droop and cross current. • MOUNTING: Behind-the-panel.
• FINISH: Dark brown, lusterless, textured, baked
SYNCHRONOUS MOTORS enamel.
On synchronous motor applications the SCP 250 can • WEIGHT: 5.75 pounds net, 8 pounds shipping.
be programmed to the desired power factor so that the • APPLICABLE TO:
motor power factor is maintained during normal loading AVC63-12, AVC125-10
conditions. Also, during transient loading conditions, SRA, SSR, SR-F, SR-H, and SR-E.
the power factor controller makes corrective motor field KR, -FF, and -FFM.
excitation adjustments and thereby minimizes the SSE.
possibility of pole slip. A typical motor application is Refer to the SCP 250 Instruction Manual 911000099Y
shown in Figure 2. for specific interconnection data.

HOW TO ORDER: SAMPLE SPECIFICATION:

Refer to the following chart to determine your require- The VAR/Power Factor controller shall be a static
ments. device. It shall provide a choice of VAR or Power Factor
control. It shall control VAR or Power Factor within ±5%
When the SCP 250 in a 60 Hertz in a 50 Hertz of maximum rated current. Provisions shall be available
is to be used in power system, power system, for field connection at the basic sensing voltages: 120-
order order
139,208-240,416-480, 520-600 VAC +5%, -10%. It shall
A generator
application SCP250 G-60 SCP250 G-50
operate over a temperature range of -40°C to +70°C. It
A motor shall contain a voltage limiting feature adjustable
application SCP250 M-60 SCP250 M-50 between ±10% and ±30% of rated voltage. The VAR/
P.F. controller shall be a Basler Model SCP 250.
 SCP250 VAR/Power Factor Controller

INTERCONNECTION DIAGRAMS

Figure 1 - Typical Interconnection Diagram - Generator Application

Figure 2 - Typical Interconnection Diagram - Motor Application

7
SCP250 VAR/Power Factor Controller

OUTLINE DRAWING

Figure 3- Outline Drawing

Note: These drawings are NOT intended for installation purposes.

Refer to Instruction Manual received with equipment for proper installation drawings.
All drawings and data subject to change without notice.
All dimensions in inches (millimeters)

ISO em
Syst
Basler

lity
®

Qua R e g
i st e r e d
Highland, IL: ISO 9001
Wasselonne, France: ISO 9001
Taylor, TX: ISO 9001

P.A.E. Les Pins, 67319 Wasselonne Cedex FRANCE Route 143, Box 269, Highland, Illinois U.S.A. 62249 1300 North Zhongshan Road, Wujiang Economic Development Zone
Tel +33 3.88.87.1010 Fax +33 3.88.87.0808 Tel +1 618.654.2341 Fax +1 618.654.2351 Suzhou, Jiangsu Province, PRC 215200
e-mail: [email protected] e-mail: [email protected] Tel +86(0)512 6346 1730 Fax +86(0)512 6346 1760
www.basler.com e-mail: [email protected]