Scribd
Upload
339 views

Tutorial Arduino Bluetooth 8 Lamp PDF

This document provides instructions for creating a Bluetooth controller lamp using an Arduino board. It includes: 1) Wiring diagrams and code to control 8 LEDs directly from the Arduino pins or using a relay module. 2) The code controls each LED individually or all at once based on commands received from a Bluetooth android app. 3) An updated code example shows how to store the lamp states in EEPROM memory to remember the last settings.

Uploaded by

Zulkarnain Zainal
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
339 views

Tutorial Arduino Bluetooth 8 Lamp PDF

This document provides instructions for creating a Bluetooth controller lamp using an Arduino board. It includes: 1) Wiring diagrams and code to control 8 LEDs directly from the Arduino pins or using a relay module. 2) The code controls each LED individually or all at once based on commands received from a Bluetooth android app. 3) An updated code example shows how to store the lamp states in EEPROM memory to remember the last settings.

Uploaded by

Zulkarnain Zainal
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 12

TUTORIAL

Bluetooth Controller Lamp


Free Version

1. Project1 Wiring With 8 LED


2. Code Program Arduino with Relay
program output to arduino active LOW
Copy code program below to arduino IDE project and Upload to Arduino modul

/*
Lamp 1 connected to PinOut 2 Arduino
Lamp 2 connected to PinOut 3 Arduino
Lamp 3 connected to PinOut 4 Arduino
Lamp 4 connected to PinOut 5 Arduino
Lamp 5 connected to PinOut 6 Arduino
Lamp 6 connected to PinOut 7 Arduino
Lamp 7 connected to PinOut 8 Arduino
Lamp 8 connected to PinOut 9 Arduino
--->you can connected to relay modul 8 channel

Serial data sending from Bluetooth Controll Lamp.apk


data '1'-'8' to on is lamp 1-8
data 'A'-'H' to off is lamp 1-8
data '9' to on ALL is lamp
data 'I' to off ALL is lamp
=====================================================================================
=*/

#include <SoftwareSerial.h>
SoftwareSerial mySerial(10, 11); //Pin10 RX , Pin 11 TX connected to--> Bluetooth TX,RX

#define Lamp1 2
#define Lamp2 3
#define Lamp3 4
#define Lamp4 5
#define Lamp5 6
#define Lamp6 7
#define Lamp7 8
#define Lamp8 9

//If Out to active Low change ON 0 and OFF 1


//If Out to active High change ON 1 and OFF 0
#define ON 1
#define OFF 0
char val;
String
statusLamp1,statusLamp2,statusLamp3,statusLamp4,statusLamp5,statusLamp6,statusLamp7,statusLam
p8;

void setup() {
pinMode(Lamp1,OUTPUT);digitalWrite (Lamp1,OFF);
pinMode(Lamp2,OUTPUT);digitalWrite (Lamp2,OFF);
pinMode(Lamp3,OUTPUT);digitalWrite (Lamp3,OFF);
pinMode(Lamp4,OUTPUT);digitalWrite (Lamp4,OFF);
pinMode(Lamp5,OUTPUT);digitalWrite (Lamp5,OFF);
pinMode(Lamp6,OUTPUT);digitalWrite (Lamp6,OFF);
pinMode(Lamp7,OUTPUT);digitalWrite (Lamp7,OFF);
pinMode(Lamp8,OUTPUT);digitalWrite (Lamp8,OFF);
mySerial.begin(9600);
Serial.begin(9600);
}

void loop() {
//cek data serial from bluetooth android App
if( mySerial.available() >0 ) {
val = mySerial.read();
Serial.println(val);
}
//Lamp is on
if( val == '1' ) {
digitalWrite(Lamp1,ON); statusLamp1="1"; }
else if( val == '2' ) {
digitalWrite(Lamp2,ON); statusLamp2="2"; }
else if( val == '3' ) {
digitalWrite(Lamp3,ON); statusLamp3="3"; }
else if( val == '4' ) {
digitalWrite(Lamp4,ON); statusLamp4="4"; }
else if( val == '5' ) {
digitalWrite(Lamp5,ON); statusLamp5="5"; }
else if( val == '6' ) {
digitalWrite(Lamp6,ON); statusLamp6="6"; }
else if( val == '7' ) {
digitalWrite(Lamp7,ON); statusLamp7="7"; }
else if( val == '8' ) {
digitalWrite(Lamp8,ON); statusLamp8="8"; }
else if( val == '9' ) {
digitalWrite(Lamp1,ON); statusLamp1="1";
digitalWrite(Lamp2,ON); statusLamp2="2";
digitalWrite(Lamp3,ON); statusLamp3="3";
digitalWrite(Lamp4,ON); statusLamp4="4";
digitalWrite(Lamp5,ON); statusLamp5="5";
digitalWrite(Lamp6,ON); statusLamp6="6";
digitalWrite(Lamp7,ON); statusLamp7="7";
digitalWrite(Lamp8,ON); statusLamp8="8";
}
//Lamp is off
else if( val == 'A' ) {
digitalWrite(Lamp1,OFF); statusLamp1="A"; }
else if( val == 'B' ) {
digitalWrite(Lamp2,OFF); statusLamp2="B"; }
else if( val == 'C' ) {
digitalWrite(Lamp3,OFF); statusLamp3="C"; }
else if( val == 'D' ) {
digitalWrite(Lamp4,OFF); statusLamp4="D"; }
else if( val == 'E' ) {
digitalWrite(Lamp5,OFF); statusLamp5="E"; }
else if( val == 'F' ) {
digitalWrite(Lamp6,OFF); statusLamp6="F"; }
else if( val == 'G' ) {
digitalWrite(Lamp7,OFF); statusLamp7="G"; }
else if( val == 'H' ) {
digitalWrite(Lamp8,OFF); statusLamp8="H"; }
else if( val == 'I' ) {
digitalWrite(Lamp1,OFF); statusLamp1="A";
digitalWrite(Lamp2,OFF); statusLamp2="B";
digitalWrite(Lamp3,OFF); statusLamp3="C";
digitalWrite(Lamp4,OFF); statusLamp4="D";
digitalWrite(Lamp5,OFF); statusLamp5="E";
digitalWrite(Lamp6,OFF); statusLamp6="F";
digitalWrite(Lamp7,OFF); statusLamp7="G";
digitalWrite(Lamp8,OFF); statusLamp8="H";
}
//synchronize Arduino to APK
else if( val == 'S' ) {
//send data to android apk
delay(500);

mySerial.println(statusLamp1+statusLamp2+statusLamp3+statusLamp4+statusLamp5+statusLamp6+stat
usLamp7+statusLamp8+"J"); //delay(500);
val=' ';
}
}

//Arduino project created by: pujar


//http://fb.me/bluetoothcontroller
//Apk Android remote controll suport this project, download on Playstore:
//Bluetooth Controll Lamp.apk
//https://play.google.com/store/apps/details?id=dev.merahkemarun.btcontrolllamp
3. Project2 Wiring 8 Lamp With Relay Modul 8CH
Input Relay active Low
4. Code Program Arduino with 8 Relay
program output to arduino active LOW
Copy code program below to arduino IDE project and Upload to Arduino modul

/*
Lamp 1 connected to PinOut 2 Arduino
Lamp 2 connected to PinOut 3 Arduino
Lamp 3 connected to PinOut 4 Arduino
Lamp 4 connected to PinOut 5 Arduino
Lamp 5 connected to PinOut 6 Arduino
Lamp 6 connected to PinOut 7 Arduino
Lamp 7 connected to PinOut 8 Arduino
Lamp 8 connected to PinOut 9 Arduino
--->you can connected to relay modul 8 channel

Serial data sending from Bluetooth Controll Lamp.apk


data '1'-'8' to on is lamp 1-8
data 'A'-'H' to off is lamp 1-8
data '9' to on ALL is lamp
data 'I' to off ALL is lamp
=====================================================================================
=*/

#include <SoftwareSerial.h>
SoftwareSerial mySerial(10, 11); //Pin10 RX , Pin 11 TX connected to--> Bluetooth TX,RX

#define Lamp1 2
#define Lamp2 3
#define Lamp3 4
#define Lamp4 5
#define Lamp5 6
#define Lamp6 7
#define Lamp7 8
#define Lamp8 9

//If Out to active Low change ON 0 and OFF 1


//If Out to active High change ON 1 and OFF 0
#define ON 0
#define OFF 1
char val;
String
statusLamp1,statusLamp2,statusLamp3,statusLamp4,statusLamp5,statusLamp6,statusLamp7,statusLam
p8;
void setup() {
pinMode(Lamp1,OUTPUT);digitalWrite (Lamp1,OFF);
pinMode(Lamp2,OUTPUT);digitalWrite (Lamp2,OFF);
pinMode(Lamp3,OUTPUT);digitalWrite (Lamp3,OFF);
pinMode(Lamp4,OUTPUT);digitalWrite (Lamp4,OFF);
pinMode(Lamp5,OUTPUT);digitalWrite (Lamp5,OFF);
pinMode(Lamp6,OUTPUT);digitalWrite (Lamp6,OFF);
pinMode(Lamp7,OUTPUT);digitalWrite (Lamp7,OFF);
pinMode(Lamp8,OUTPUT);digitalWrite (Lamp8,OFF);
mySerial.begin(9600);
Serial.begin(9600);
}

void loop() {
//cek data serial from bluetooth android App
if( mySerial.available() >0 ) {
val = mySerial.read();
Serial.println(val);
}
//Lamp is on
if( val == '1' ) {
digitalWrite(Lamp1,ON); statusLamp1="1"; }
else if( val == '2' ) {
digitalWrite(Lamp2,ON); statusLamp2="2"; }
else if( val == '3' ) {
digitalWrite(Lamp3,ON); statusLamp3="3"; }
else if( val == '4' ) {
digitalWrite(Lamp4,ON); statusLamp4="4"; }
else if( val == '5' ) {
digitalWrite(Lamp5,ON); statusLamp5="5"; }
else if( val == '6' ) {
digitalWrite(Lamp6,ON); statusLamp6="6"; }
else if( val == '7' ) {
digitalWrite(Lamp7,ON); statusLamp7="7"; }
else if( val == '8' ) {
digitalWrite(Lamp8,ON); statusLamp8="8"; }
else if( val == '9' ) {
digitalWrite(Lamp1,ON); statusLamp1="1";
digitalWrite(Lamp2,ON); statusLamp2="2";
digitalWrite(Lamp3,ON); statusLamp3="3";
digitalWrite(Lamp4,ON); statusLamp4="4";
digitalWrite(Lamp5,ON); statusLamp5="5";
digitalWrite(Lamp6,ON); statusLamp6="6";
digitalWrite(Lamp7,ON); statusLamp7="7";
digitalWrite(Lamp8,ON); statusLamp8="8";
}
//Lamp is off
else if( val == 'A' ) {
digitalWrite(Lamp1,OFF); statusLamp1="A"; }
else if( val == 'B' ) {
digitalWrite(Lamp2,OFF); statusLamp2="B"; }
else if( val == 'C' ) {
digitalWrite(Lamp3,OFF); statusLamp3="C"; }
else if( val == 'D' ) {
digitalWrite(Lamp4,OFF); statusLamp4="D"; }
else if( val == 'E' ) {
digitalWrite(Lamp5,OFF); statusLamp5="E"; }
else if( val == 'F' ) {
digitalWrite(Lamp6,OFF); statusLamp6="F"; }
else if( val == 'G' ) {
digitalWrite(Lamp7,OFF); statusLamp7="G"; }
else if( val == 'H' ) {
digitalWrite(Lamp8,OFF); statusLamp8="H"; }
else if( val == 'I' ) {
digitalWrite(Lamp1,OFF); statusLamp1="A";
digitalWrite(Lamp2,OFF); statusLamp2="B";
digitalWrite(Lamp3,OFF); statusLamp3="C";
digitalWrite(Lamp4,OFF); statusLamp4="D";
digitalWrite(Lamp5,OFF); statusLamp5="E";
digitalWrite(Lamp6,OFF); statusLamp6="F";
digitalWrite(Lamp7,OFF); statusLamp7="G";
digitalWrite(Lamp8,OFF); statusLamp8="H";
}
//synchronize Arduino to APK
else if( val == 'S' ) {
//send data to android apk
delay(500);

mySerial.println(statusLamp1+statusLamp2+statusLamp3+statusLamp4+statusLamp5+statusLamp6+stat
usLamp7+statusLamp8+"J"); //delay(500);
val=' ';
}
}

//Arduino project created by: pujar


//http://fb.me/bluetoothcontroller
//Apk Android remote controll suport this project, download on Playstore:
//Bluetooth Controll Lamp.apk
//https://play.google.com/store/apps/details?id=dev.merahkemarun.btcontrolllamp
5. Code Program Arduino 8 Relay With EEPROM
#include <SoftwareSerial.h>
#include <EEPROM.h>
SoftwareSerial mySerial(10, 11); //Pin10 RX , Pin 11 TX connected to--> Bluetooth TX,RX

#define Lamp1 2
#define Lamp2 3
#define Lamp3 4
#define Lamp4 5
#define Lamp5 6
#define Lamp6 7
#define Lamp7 8
#define Lamp8 9

//If Out to active Low change ON 0 and OFF 1


//If Out to active High change ON 1 and OFF 0
#define ON 0
#define OFF 1
char val;
byte .... UPDATE to PRO Version
String
statusLamp1,statusLamp2,statusLamp3,statusLamp4,statusLamp5,statusLamp6,statusLamp7,statusLam
p8;

void setup() {
pinMode(Lamp1,OUTPUT);digitalWrite (Lamp1,OFF);
pinMode(Lamp2,OUTPUT);digitalWrite (Lamp2,OFF);
pinMode(Lamp3,OUTPUT);digitalWrite (Lamp3,OFF);
pinMode(Lamp4,OUTPUT);digitalWrite (Lamp4,OFF);
pinMode(Lamp5,OUTPUT);digitalWrite (Lamp5,OFF);
pinMode(Lamp6,OUTPUT);digitalWrite (Lamp6,OFF);
pinMode(Lamp7,OUTPUT);digitalWrite (Lamp7,OFF);
pinMode(Lamp8,OUTPUT);digitalWrite (Lamp8,OFF);
mySerial.begin(9600);
Serial.begin(9600);
ReadEeprom();
}

void loop() {
...............................................
..............................................

UPDATE to PRO Version


6. Try APPS and Pair Bluetooth Modul to Android Device
5. Download Program
Check for Update Bluetooth Controller 8 Lamp APPS for PREMIUM Version
https://play.google.com/store/apps/details?id=dev.merahkemarun.btcontrollamp

WHY YOU SHOULD UPGRADE to the PREMIUM?


If you upgrade to premium/PRO, then you will not find ads that appear in
applications (remove ads).

And you'll get the best features in addition to remove the ads, which feature key
synchronization of the lights being lit as shown in the video.

Download File:
-Program Code arduino project with 8 LED
https://www.dropbox.com/s/f13qc8g929ze8ft/Arduino_Bluetooth_8Lamp_with_LED.zip?dl=1
-Program Code arduino project with 8 Relay
https://www.dropbox.com/s/c49htqkmjwhbngg/Arduino_Bluetooth_8Lamp_with_Relay.zip?dl=1
-Program Code arduino project 8 Relay EEPROM
........................................................Update to Pro Versions
-Program Code cvavr project atmega16 ZIP
https://goo.gl/CDC9ei

6. Video Tutorial:
Bluetooth Controller 8 Lamp FREE vs PREMIUM
https://www.facebook.com/groups/257664444610751/permalink/283811955329333/
Setting And Connected Arduino Bluetooth to Phone Device Android
https://www.facebook.com/groups/257664444610751/permalink/283755208668341/
Bluetooth Controller 8 Lamp Program Tutorial for Arduino Project
https://www.facebook.com/groups/257664444610751/permalink/283790505331478/
7. Recommendation product Best seller from Amazon.com

Product Name Price Link Image


IEIK UNO R3 Board  $8.99 http://amzn.to/219BA4L
ATmega328P with USB Cable
for Arduino

HC-05 Wireless Bluetooth Host $8.99 http://amzn.to/1U8v2S7


Serial Transceiver Module
Slave and Master RS232 For
Arduino
4 Channel DC 5V Relay Module $6.99 http://amzn.to/1U8u8Fg

8 Channel DC 5V Relay Module $8.98 http://amzn.to/1XbBtY3

120pcs Multicolored 40pin Male $9.99 http://amzn.to/22TGODi


to Female, 40pin Male to Male,
40pin Female to Female
Breadboard Jumper Wires
Ribbon Cables Kit

Complete Starter Kit for Arduino $52.99 http://amzn.to/1regjut

37-in-1 Sensor Module Kit for $28.68 http://amzn.to/1UCzIwz


Arduino

You might also like