INTEGRATED CIRCUITS

DATA SHEET

TDA1001B
TDA1001BT
Interference and noise suppression
circuit for FM receivers
Product specification December 1982
File under Integrated Circuits, IC01
Philips Semiconductors Product specification

Interference and noise suppression TDA1001B

circuit for FM receivers TDA1001BT

GENERAL DESCRIPTION
The TDA1001B is a monolithic integrated circuit for suppressing interference and noise in FM mono and stereo receivers.

Features
• Active low-pass and high-pass filters
• Interference pulse detector with adjustable and controllable response sensitivity
• Noise detector designed for FM i.f. amplifiers with ratio detectors or quadrature detectors
• Schmitt trigger for generating an interference suppression pulse
• Active pilot tone generation (19 kHz)
• Internal voltage stabilization

QUICK REFERENCE DATA

Supply voltage (pin 9) VP typ. 12 V
Supply current (pin 9) IP typ. 14 mA
A.F. input signal handling (pin 1)
(peak-to-peak value) Vi(p-p) typ. 1 V
Input resistance (pin 1) Ri min. 35 kΩ
Voltage gain (V1-16/V6-16) Gv typ. 0,5 dB
Total harmonic distortion THD typ. 0,25 %
Bandwidth B typ. 70 kHz
Suppression pulse threshold voltage
(peak value); R13 = 0 Vi(tr)OM typ. 19 mV
Suppression pulse duration ts typ. 27 µs
Supply voltage range (pin 9) VP 7,5 to 16 V
Operating ambient temperature range Tamb −30 to + 80 °C

PACKAGE OUTLINE
TDA1001B: 16-lead DIL; plastic (SOT38); SOT38-1; 1996 September 06.
TDA1001BT: 16-lead mini-pack; plastic (SO16; SOT109A); SOT116-1; 1996 September 06.

December 1982 2
Philips Semiconductors Product specification

Interference and noise suppression circuit TDA1001B

for FM receivers TDA1001BT

Fig.1 Block diagram.

December 1982 3
Philips Semiconductors Product specification

Interference and noise suppression circuit TDA1001B

for FM receivers TDA1001BT

RATINGS
Limiting values in accordance with the Absolute Maximum System (IEC 134)
Supply voltage (pin 9) VP max. 18 V
Input voltage (pin 1) V1-16 max. VP V
Output current (pin 6) I6 max. 1 mA
−I6 max. 15 mA
Total power dissipation see derating curves Fig.2
Storage temperature range Tstg −65 to +150 °C
Operating ambient temperature range Tamb −30 to +80 °C

 in plastic DIL (SOT-38) package (TDA1001B).

− − − − − − in plastic mini-pack (SO-16; SOT-109A) package (TDA1001BT); mounted on a ceramic substrate of 50 × 15 × 0,7 mm.

Fig.2 Power derating curves.

December 1982 4
Philips Semiconductors Product specification

Interference and noise suppression circuit TDA1001B

for FM receivers TDA1001BT

CHARACTERISTICS
VP = 12 V; Tamb = 25 °C; measured in Fig.4; unless otherwise specified

PARAMETER SYMBOL MIN. TYP. MAX. UNIT

Input stage
Input impedance (pin 1)
f = 40 kHz Zi1 − 45 − kΩ
Input resistance (pin 1)
with pin 2 not connected Ri1 − 600 − kΩ
Input bias current (pin 1)
V1-16 = 4,8 V Ii1 − 6 15 µA
Output resistance (pin 2)
unloaded Ro2 low-ohmic
Internal emitter resistance R2-16 − 5,6 − kΩ
Low-pass amplifier
Input resistance (pin 3) Ri3 10 − − MΩ
Input bias current (pin 3) Ii3 − − 7 µA
Output resistance (pin 4) Ro4 − − 5 Ω
Voltage gain (V4/V3) Gv4/3 − 1,1 −
Suppression pulse stage
Input offset current at pin 5
during the suppression time tS Iio5 − 50 200 nA
Output stage
Output resistance (pin 6) Ro6 low-ohmic
Internal emitter resistance R6-16 − 6 − kΩ
Current gain (I5/I6) Gi5/6 − 85 − dB
Pilot tone generation (19 kHz)
Input impedance (pin 8) Zi8 − − 1 Ω
Output impedance (pin 7)
pin 8 open Zo7 150 − − kΩ
Output bias current (pin 7) Io7 0,7 1 1,3 mA
Current gain (I7/I8) Gi7/8 − 3 −
High-pass amplifier
Input resistance (pin 15) Ri15 10 − − MΩ
Input bias current (pin 15) Ii15 − − 7 µA
Output resistance (pin 14) Ro14 − − 5 Ω
Voltage gain (V14/15) Gv14/15 − 1,4 −

December 1982 5
Philips Semiconductors Product specification

Interference and noise suppression circuit TDA1001B

for FM receivers TDA1001BT

PARAMETER SYMBOL MIN. TYP. MAX. UNIT

A.G.C. amplifier; interference and noise detectors
Internal resistance (pins 13 and 14) R13-14 1,5 2,0 2,5 kΩ
Operational threshold voltage
(uncontrolled); peak value (pin 14)
of the interference pulse detector ± V14int m − 15 − mV
of the noise detector ± V14n m − 6,5 − mV
Output voltage (peak value; pin 11) V11-16M 5,2 5,8 6,4 V
Output control current (pin 12)
(peak value) I12M 150 200 250 µA
Output bias current (pin 12) Io12 − 2,5 6 µA
Input threshold voltage for onset of control (pin 12) V12-9 360 425 500 mV
(Vi(tr)O+ 3 dB) or: − 0,66VBE − mV
Suppression pulse generation (Schmitt trigger)
Switching threshold (pin 11)
1: gate disabled V11-16 − 3,2 − V
2: gate enabled V11-16 − 2,0 − V
Switching hysteresis ∆V11-16 − 1,2 − V
Input offset current (pin 11) Iio11 − − 100 nA
Output current (pin 10)
gate disabled; peak value Io10M 0,6 1 1,4 mA
Reverse output current (pin 10) IR10 − − 2 µA
Sensitivity (pin 10) V10-16 2,5 − − V

December 1982 6
Philips Semiconductors Product specification

Interference and noise suppression circuit TDA1001B

for FM receivers TDA1001BT

APPLICATION INFORMATION
VP = 12 V; Tamb = 25 °C; f = 1 kHz; measured in Fig.4; unless otherwise specified

PARAMETER SYMBOL MIN. TYP. MAX. UNIT

Supply voltage range (pin 9) VP 7,5 12 16 V
Quiescent supply current (pin 9) IP 10 14 18 mA
Signal path
D.C. input voltage (pin 1) V1-16 − 4,5 − V
Input impedance (pin 1); f = 40 kHz |Zi1| 35 − − kΩ
D.C. output voltage (pin 6) V6-16 2,4 2,8 − V
Output resistance (pin 6) Ro6 low-ohmic
Voltage gain (V6/V1) Gv6/1 0 0,5 1 dB
−3 dB point of low-pass filter f(−3dB) − 70 − kHz
Sensitivity for THD < 0,5%
(peak-to-peak value) Vi(p-p) 1,2 1,8 − V
Residual interference pulse after suppression
(see Fig.3); pin 7 to ground;
Vi(tr)M = 100mV; (peak-to-peak value) V6-16(p-p) − − 3 mV
Interference suppression at R13 = 0;
notes 5 and 6; Vi(rms) = 30 mV; f = 19 kHz
(sinewave); Vi(tr)M = 60 mV; fr = 400 Hz αint 20 30 − dB
Interference processing
Input signal at pin 1; output signal at pin 10
Suppression pulse threshold voltage; control
function OFF (pin 9 connected to pin 12);
r.m.s. value; note 1
measured with sinewave input signal
f = 120 kHz; −V10-9 > 1 V
at R13 = 0 Ω Vi(tr)rms 8 11 14 mV
at R13 = 2,7 kΩ Vi(tr)rms 18 28,5 40 mV
voltage difference for safe triggering/
non-triggering (r.m.s. value) ∆Vi(rms) − 1 − mV
measured with interference pulses
f = 400 Hz (see Fig.3); peak value
at R13 = 0 Ω Vi(tr)M − 19 − mV
at R13 = 2,7 kΩ Vi(tr)M − 45 − mV
Suppression pulse duration (note 2) tS 24 27 30 µs

December 1982 7
Philips Semiconductors Product specification

Interference and noise suppression circuit TDA1001B

for FM receivers TDA1001BT

PARAMETER SYMBOL MIN. TYP. MAX. UNIT

Noise threshold feedback control (notes 1 and 3)
Noise input voltage (r.m.s. value) f = 120 kHz
sinewave for V12-9 = 300 mV
at R13 = 0 Ω Vni(rms) 2,3 3,3 4,3 mV
at R13 = 2,7 kΩ Vni(rms) − 8,2 − mV
for V12-9 = 425 mV (Vi(tr)O + 3 dB)
at R13 = 0 Ω Vni(rms) − 7,3 − mV
at R13 = 2,7 kΩ Vni(rms) − 16,5 − mV
for V12-9 = 560 mV (Vi(tr)O + 20 dB)
at R13 = 0 Ω Vni(rms) 33 45 57 mV
at R13 = 2,7 kΩ Vni(rms) − 107 − mV
Amplification control voltage by interference intensity
(note 4)
Vi(rms) = 50 mV; f = 19 kHz;
Vi(tr)M = 300 mV; r.m.s. value
at repetition frequency fr = 1 kHz Vo6(rms) 49 − 56 mV
at repetition frequency fr = 16 kHz Vo6(rms) 45 − 65 mV
Notes to application information
1. The interference suppression and noise feedback control thresholds can be determined by R13 or a capacitive
voltage divider at the input of the high-pass filter and they are defined by the following formulae:
Vi(tr) = (1 + R13/RS) × Vi(tr)O in which RS = 2 kΩ;
Vni = (1 + R13/RS) × VniO in which RS = 2 kΩ.
2. The suppression pulse duration is determined by C11 = 2,2 nF and R11 = 6,8 kΩ.
3. The characteristic of the noise feedback control is determined by R12 (and R10).
4. The feedback control of the interference suppression threshold at higher repetition frequencies is determined by R10
(and R12).
5. The 19 kHz generator can be adjusted with R7-16 (and R7-8). Adjustment is not required if components with small
tolerances are used e.g. ∆R < 1% and ∆C < 2%.
6. Measuring conditions:
The peak output noise voltage (Vno m, CCITT filter) shall be measured at the output with a de-emphazing time T = 50
µs (R = 5 kΩ, C = 10 nF); the reference value of 0 dB is Vo int with the 19 kHz generator short-circuited (pin 7
grounded).

December 1982 8
Philips Semiconductors Product specification

Interference and noise suppression circuit TDA1001B

for FM receivers TDA1001BT

Fig.3 Measuring signal for interference suppression; at the input (pin 1) a square-wave is applied with a duration
of ttr = 10 µs and with rise and fall times tr = tf = 10 ns.

Fig.4 Application circuit diagram.

December 1982 9
Philips Semiconductors Product specification

Interference and noise suppression circuit TDA1001B

for FM receivers TDA1001BT

PACKAGE OUTLINES

DIP16: plastic dual in-line package; 16 leads (300 mil); long body SOT38-1

D ME
seating plane

A2 A

A1
L

c
Z e w M
b1
(e 1)
b
16 9 MH

pin 1 index
E

1 8

0 5 10 mm
scale

DIMENSIONS (inch dimensions are derived from the original mm dimensions)

UNIT
A A1 A2
b b1 c D (1) E (1) e e1 L ME MH w Z (1)
max. min. max. max.
1.40 0.53 0.32 21.8 6.48 3.9 8.25 9.5
mm 4.7 0.51 3.7 2.54 7.62 0.254 2.2
1.14 0.38 0.23 21.4 6.20 3.4 7.80 8.3
0.055 0.021 0.013 0.86 0.26 0.15 0.32 0.37
inches 0.19 0.020 0.15 0.10 0.30 0.01 0.087
0.045 0.015 0.009 0.84 0.24 0.13 0.31 0.33

Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.

OUTLINE REFERENCES EUROPEAN

ISSUE DATE
VERSION IEC JEDEC EIAJ PROJECTION

92-10-02
SOT38-1 050G09 MO-001AE
95-01-19

December 1982 10
Philips Semiconductors Product specification

Interference and noise suppression circuit TDA1001B

for FM receivers TDA1001BT

SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1

D E A
X

y HE v M A

16 9

Q
A2
(A 3) A
A1
pin 1 index
θ
Lp

1 8 L

e w M detail X
bp

0 2.5 5 mm
scale

DIMENSIONS (inch dimensions are derived from the original mm dimensions)

A
UNIT max. A1 A2 A3 bp c D (1) E (1) e HE L Lp Q v w y Z (1) θ

0.25 1.45 0.49 0.25 10.0 4.0 6.2 1.0 0.7 0.7
mm 1.75 0.25 1.27 1.05 0.25 0.25 0.1 o
0.10 1.25 0.36 0.19 9.8 3.8 5.8 0.4 0.6 0.3 8
0.0098 0.057 0.019 0.0098 0.39 0.16 0.24 0.039 0.028 0.028 0o
inches 0.069 0.01 0.050 0.041 0.01 0.01 0.004
0.0039 0.049 0.014 0.0075 0.38 0.15 0.23 0.016 0.020 0.012

Note
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.

OUTLINE REFERENCES EUROPEAN

ISSUE DATE
VERSION IEC JEDEC EIAJ PROJECTION

91-08-13
SOT109-1 076E07S MS-012AC
95-01-23

December 1982 11
Philips Semiconductors Product specification

Interference and noise suppression circuit TDA1001B

for FM receivers TDA1001BT

SOLDERING Several techniques exist for reflowing; for example,

thermal conduction by heated belt. Dwell times vary
Introduction between 50 and 300 seconds depending on heating
There is no soldering method that is ideal for all IC method. Typical reflow temperatures range from
packages. Wave soldering is often preferred when 215 to 250 °C.
through-hole and surface mounted components are mixed Preheating is necessary to dry the paste and evaporate
on one printed-circuit board. However, wave soldering is the binding agent. Preheating duration: 45 minutes at
not always suitable for surface mounted ICs, or for 45 °C.
printed-circuits with high population densities. In these
situations reflow soldering is often used.
WAVE SOLDERING
This text gives a very brief insight to a complex technology.
Wave soldering techniques can be used for all SO
A more in-depth account of soldering ICs can be found in
packages if the following conditions are observed:
our “IC Package Databook” (order code 9398 652 90011).
• A double-wave (a turbulent wave with high upward
DIP pressure followed by a smooth laminar wave) soldering
technique should be used.
SOLDERING BY DIPPING OR BY WAVE
• The longitudinal axis of the package footprint must be
The maximum permissible temperature of the solder is parallel to the solder flow.
260 °C; solder at this temperature must not be in contact • The package footprint must incorporate solder thieves at
with the joint for more than 5 seconds. The total contact the downstream end.
time of successive solder waves must not exceed
5 seconds. During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
The device may be mounted up to the seating plane, but applied by screen printing, pin transfer or syringe
the temperature of the plastic body must not exceed the dispensing. The package can be soldered after the
specified maximum storage temperature (Tstg max). If the adhesive is cured.
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the Maximum permissible solder temperature is 260 °C, and
temperature within the permissible limit. maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150 °C within
REPAIRING SOLDERED JOINTS 6 seconds. Typical dwell time is 4 seconds at 250 °C.

Apply a low voltage soldering iron (less than 24 V) to the A mildly-activated flux will eliminate the need for removal
lead(s) of the package, below the seating plane or not of corrosive residues in most applications.
more than 2 mm above it. If the temperature of the
soldering iron bit is less than 300 °C it may remain in REPAIRING SOLDERED JOINTS
contact for up to 10 seconds. If the bit temperature is Fix the component by first soldering two diagonally-
between 300 and 400 °C, contact may be up to 5 seconds. opposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
SO time must be limited to 10 seconds at up to 300 °C. When
REFLOW SOLDERING using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
Reflow soldering techniques are suitable for all SO 270 and 320 °C.
packages.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.

December 1982 12
Philips Semiconductors Product specification

Interference and noise suppression circuit TDA1001B

for FM receivers TDA1001BT

DEFINITIONS

Data sheet status

Objective specification This data sheet contains target or goal specifications for product development.
Preliminary specification This data sheet contains preliminary data; supplementary data may be published later.
Product specification This data sheet contains final product specifications.
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.

LIFE SUPPORT APPLICATIONS

These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.

December 1982 13
This datasheet has been download from:

www.datasheetcatalog.com

Datasheets for electronics components.