Internal Use Only

Website http://biz.lgservice.com

SERVICE MANUAL
KARAOKE MINI
Hi-Fi SYSTEM

MODEL : FBD203 (FBS203V)

SERVICE MANUAL
CAUTION
BEFORE SERVICING THE UNIT, READ THE “SAFETY PRECAUTIONS” IN THIS MANUAL.

SEPTEMBER, 2008
P/NO : AFN62795884
MODEL : FBD203 (FBS203V)
 [CONTENTS]
❍ SECTION 1. GENERAL
• SERVICING PRECAUTIONS ................................................................................................ 1-2
• ESD PRECAUTIONS ............................................................................................................ 1-4
• SERVICE INFORMATION FOR EEPROM ............................................................................ 1-5
• PROGRM DOWNLOAD GUIDE ............................................................................................ 1-7
• SPECIFICATIONS .............................................................................................................. 1-11

❍ SECTION 2. EXPLODED VIEWS

• CABINET AND MAIN FRAME SECTION.............................................................................. 2-1
• DECK MECHANISM EXPLODED VIEW ................................................................................ 2-3
• SPEAKER EXPLODED VIEW .............................................................................................. 2-5
• PACKING ACCESSORY VIEW.............................................................................................. 2-6

❍ SECTION 3. ELECTRICAL PART

• TROUBLESHOOTING GUIDE
AUDIO PART TROUBLESHOOTING GUIDE ........................................................................ 3-1
DVD PART TROUBLESHOOTING GUIDE .......................................................................... 3-11
• WAVEFORMS OF MAJOR CHECK POINT ........................................................................ 3-19
• WIRING DIAGRAM .............................................................................................................. 3-25
• BLOCK DIAGRAM .............................................................................................................. 3-26
• CIRCUIT DIAGRAMS .......................................................................................................... 3-27
• INTERNAL BLOCK DIAGRAM OF IC ................................................................................ 3-47
• CIRCUIT VOLTAGE CHART ................................................................................................ 3-63
• PRINTED CIRCUIT DIARGAMS ........................................................................................ 3-67

❍ SECTION 4. REPLACEMENT PARTS LIST ................................................................ 4-1

Copyright © 2008 LG Electronics. Inc. All right reserved. 1-1 LGE Internal Use Only
Only for training and service purposes
 SECTION 1. GENERAL
SERVICING PRECAUTIONS
NOTES REGARDING HANDLING OF THE PICK-UP
1. Notes for transport and storage
1) The pick-up should always be left in its conductive bag until immediately prior to use.
2) The pick-up should never be subjected to external pressure or impact.

Storage in conductive bag Drop impact

2. Repair notes
1) The pick-up incorporates a strong magnet, and so should never be brought close to magnetic materials.
2) The pick-up should always be handled correctly and carefully, taking care to avoid external pressure and
impact. If it is subjected to strong pressure or impact, the result may be an operational malfunction and/or
damage to the printed-circuit board.
3) Each and every pick-up is already individually adjusted to a high degree of precision, and for that reason
the adjustment point and installation screws should absolutely never be touched.
4) Laser beams may damage the eyes!
Absolutely never permit laser beams to enter the eyes!
Also NEVER switch ON the power to the laser output part (lens, etc.) of the pick-up if it is damaged.
5) Cleaning the lens surface

NEVER look directly at the laser beam, and don’t allow

contact fingers or other exposed skin.

If there is dust on the lens surface, the dust should be cleaned away by using an air bush (such as used
for camera lens). The lens is held by a delicate spring. When cleaning the lens surface, therefore, a cotton
swab should be used, taking care not to distort this.

Pressure
Magnet
Pressure

How to hold the pick-up

Cotton swab

Conductive Sheet
6) Never attempt to disassemble the pick-up.
Spring by excess pressure. If the lens is extremely dirty, apply isopropyl alcohol to the cotton swab.
(Do not use any other liquid cleaners, because they will damage the lens.) Take care not to use too much
of this alcohol on the swab, and do not allow the alcohol to get inside the pick-up.

LGE Internal Use Only 1-2 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
NOTES REGARDING COMPACT DISC PLAYER REPAIRS
1. Preparations
1) Compact disc players incorporate a great many ICs as well as the pick-up (laser diode). These components
are sensitive to, and easily affected by, static electricity. If such static electricity is high voltage, components
can be damaged, and for that reason components should be handled with care.
2) The pick-up is composed of many optical components and other high-precision components. Care must be
taken, therefore, to avoid repair or storage where the temperature of humidity is high, where strong magnet-
ism is present, or where there is excessive dust.
2. Notes for repair
1) Before replacing a component part, first disconnect the power supply lead wire from the unit
2) All equipment, measuring instruments and tools must be grounded.
3) The workbench should be covered with a conductive sheet and grounded.
When removing the laser pick-up from its conductive bag, do not place the pick-up on the bag. (This is
because there is the possibility of damage by static electricity.)
4) To prevent AC leakage, the metal part of the soldering iron should be grounded.
5) Workers should be grounded by an armband (1M Ω)
6) Care should be taken not to permit the laser pick-up to come in contact with clothing, in order to prevent sta-
tic electricity changes in the clothing to escape from the armband.
7) The laser beam from the pick-up should NEVER be directly facing the eyes or bare skin.

Armband

Resistor
(1 Mohm)
Resistor
Conductive
(1 Mohm)
Sheet

Copyright © 2008 LG Electronics. Inc. All right reserved. 1-3 LGE Internal Use Only
Only for training and service purposes
 SAFETY PRECAUTIONS
Electrostatically Sensitive Devices (ESD)
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components
commonly are called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated
circuits and some field-effect transistors and semiconductor chip components. The following techniques should
be used to help reduce the incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off
any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a
commercially available discharging wrist strap device, which should be removed for potential shock reasons
prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ESD devices, place the assembly on a conductive surface
such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ESD devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can
generate electrical charges sufficient to damage ESD devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESD
devices.
6. Do not remove a replacement ESD device from its protective package until immediately before you are
ready to install it. (Most replacement ESD devices are packaged with leads electrically shorted together by
conductive foam, aluminum foil or comparable conductive materials).
7. Immediately before removing the protective material from the leads of a replacement ESD device, touch the
protective material to the chassis or circuit assembly into which the device will by installed.

CAUTION : BE SURE NO POWER IS APPLIED TO THE CHASSIS OR CIRCUIT, AND OBSERVE ALL OTHER
SAFETY PRECAUTIONS.

8. Minimize bodily motions when handing unpackaged replacement ESD devices. (Otherwise harmless motion
such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can gener-
ate static electricity sufficient to damage an ESD device).

CAUTION. GRAPHIC SYMBOLS

THE LIGHTNING FLASH WITH APROWHEAD SYMBOL. WITHIN AN EQUILATERAL TRIANGLE, IS
INTENDED TO ALERT THE SERVICE PERSONNEL TO THE PRESENCE OF UNINSULATED
“DANGEROUS VOLTAGE” THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF
ELECTRIC SHOCK.

THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE

SERVICE PERSONNEL TO THE PRESENCE OF IMPORTANT SAFETY INFORMATION IN SERVICE
LITERATURE.

LGE Internal Use Only 1-4 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
 SERVICE INFORMATION FOR EEPROM (MICOM PART)

POWER ON

FLD no disc status

Remote control ‘2’ + Front ‘STOP’ DETECT NEW EEPROM

push same timing during 5s (OPTION EDIT SCREEN)

MODEL : FBD203
NAME HEX
OPT 1 00
FLD ‘OP-0…. OPT 2 00
OPT 3 00
OPT 4 00
OPT 5 00
Use arrow key ( ) move
to appropriate position and make
changes

Press ENTER key once

FLD ‘write ok’

Remote control ‘2’ + Front ‘STOP’

push same timing

FLD display E2P CLR or EP CLR

Auto power off

Copyright © 2008 LG Electronics. Inc. All right reserved. 1-5 LGE Internal Use Only
Only for training and service purposes
 SERVICE INFORMATION FOR EEPROM (DVD PART)

POWER ON

DETECT NEW EEPROM

DVD LOGO Status (NO Disk status) (OPTION EDIT SCREEN)

NAME HEX
OPT 1 00
Remote control
OPT 2 00
Pause key-->1-->4-->7-->2 in order. OPT 3 00
OPT 4 00
OPT 5 00
OPT 6 00
Press number 0~9, Press character OPT 7 00
A~F (1~6 for a while) OPT 8 00
OPT 9 00
OPT A 00
OPT B 00
Use arrow key ( ) to
OPT C 00
move to appropriate position and
OPT D 00
make changes
OPT E 00
OPT F 00
OPT G 00
Press pause key once

Change will be applied when power

OFF-->ON.

LGE Internal Use Only 1-6 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
 PROGRM DOWNLOAD GUIDE

• AUDIO USB DOWNLOAD GUIDE

The name of the program file to download is FBD203_date.hex.

- At some PCs with the security program (Water Wall) installed, store it at the USB device, disable
the security protection, and download it to the set.

Note) Do not perform any other work such as disconnecting the USB device, switching to the
other Function and turning off the power while downloading it to the set.
The USB device should be disconnected after completing the download.

1. When the USB device is inserted at the USB function a after a while TV screen is displayed on the
as following figure.

Copyright © 2008 LG Electronics. Inc. All right reserved. 1-7 LGE Internal Use Only
Only for training and service purposes
2. The message “Upgrade” is displayed while downloading.

3. The power is automatically turned off when downloading is completed.

LGE Internal Use Only 1-8 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
• DVD USB DOWN LOAD GUIDE

The program file to download should be named as BANK30.ROM.

- The downloaded file should be modified as BANK30.ROM to use.
- At some PCs with the security program (Water Wall) installed, store BANK30.ROM at the USB
device, disable the security protection, and download it to the set.
- After safely storing BANK30. ROM at the USB device, perform the following steps.

Note) Do not perform any other work such as disconnecting the USB device, switching to the
other Function and turning off the power while downloading it to the set.

1. When the USB device is inserted at the USB functiona after a while TV screen is displayed on the
as following figure.

2. When downloading is completed, the message “Completed” is displayed at the top left of the TV screen
as shown at Figure(1).
If the message “NO USB” is displayed as shown at Figure(2), downloading is completed.

FIG.2

FIG.1

Copyright © 2008 LG Electronics. Inc. All right reserved. 1-9 LGE Internal Use Only
Only for training and service purposes
3. Turn on the power, press the SETUP button of the remote controller at the USB FUNCTION.
When the SETUP window is displayed on the screen, move down once to select the DISPLAY menu.
Go to the TV Aspect at the right menu, move to “16:9”, enter “1397139” by using the numeric key of the
remote controller, and then press the Enter key.
Then, the System Information screen is displayed as shown inthe following figure. If not, retry the steps
at the above.

Left Right

Down
4. When Step 3 is completed, press the PAUSE KEY of the remote controller.

5. Disconnect the power code, and reconnect it after 5 seconds to complete downloading.

7. When the power is turned on again, the language selection menu is initially displayed.
After selecting the desired language, press the SELECT/ENTER.

LGE Internal Use Only 1-10 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
 SPECIFICATIONS

General
Power supply Refer to main label.
Power consumption Refer to main label.
Net Weight 3.42 kg
External dimensions (W x H x D) 330 x 138.5x 252.4 mm
Operating conditions Temperature: 5° C to 35° C, Operation status: Horizontal
Operating humidity 5% to 85%

Tuner
FM Tuning Range 87.5 - 108.0 MHz or 65.0 - 74.0 MHz, 87.5 - 108.0 MHz
Intermediate Frequency 10.7 MHz
AM Tuning Range 522 - 1,620 kHz or 520 - 1,720 kHz
Intermediate Frequency 450 kHz

Amplifier
OUTPUT POWER 100 W + 100 W (4Ω, THD 0.5%) : FBD203
50 W + 50 W( 4Ω, THD 0.5%) : FBD103
Stereo Mode 100 W + 100 W (4Ω, THD 0.5%) : FBD203
50 W + 50 W( 4Ω, THD 0.5%) : FBD103
Frequency Response 40 - 20000Hz
Signal- to- noise ratio 75dB

DVD/ VCD/ CD player

Frequency response (audio) 40 - 20000 Hz
Signal- to- noise ratio (audio) More than 75 dB (1 kHz)
Signal- to- noise ratio (video) More than 55 dB (1 kHz)
Dynamic range (audio) More than 80 dB
Video output 1.0 V (p- p), 75 Ω
Component Video output (Y) 1.0 V (p- p), 75 Ω

Speakers
FBS203V
Type 2Way 2Speaker
Impedance 4Ω
Rated Input Power 100 W
Max. Input Power 200W
Net Dimensions (W x H x D) 165 X 341 X 261 mm
Net Weight 4.48 kg

Designs and specifications are subject to change without pior notice.

Copyright © 2008 LG Electronics. Inc. All right reserved. 1-11 LGE Internal Use Only
Only for training and service purposes
LGE Internal Use Only 1-12 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
 SECTION 2. EXPLODED VIEWS
NOTES) THE EXCLAMATION POINT WITHIN AN
EQUILATERAL TRIANGLE IS INTENDED

• CABINET AND MAIN FRAME SECTION TO ALERT THE SERVICE PERSONNEL

TO THE PRESENCE OF IMPORTANT
SAFETY INFORMATION IN SERVICE
LITERATURE.
453
B

C
SC
A AR
T

A46 MAIN
B
E
471
F D
G
CABLE1
471 A47

C
273
SMPS
A43 453
CABLE2 453
A
259
G
A42 FR
ON H 453 453
T E
I
257 258 453
F

MIC
453

453

256 465
A26 250
453 272
271 255 H 260 D
I 453
CABLE3
271
254
253 453

300

270

A44

271

Copyright © 2008 LG Electronics. Inc. All right reserved. 2-1 2-2 LGE Internal Use Only
Only for training and service purposes
DECK MECHANISM EXPLODED VIEW
1. DECK MECHANISM SECTION (DP-10)

001 A01
A26 002
003
439 018

014 A02

013

020

017

012
435

015B
015

015A
019
016
440
432
012A
012
030
010

026

439

024

025
431
036
435

012A
A03

021

430

LGE Internal Use Only 2-3 2-4 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
 SPEAKER EXPLODED VIEW
• FRONT SPEAKER (FBS203V)

A80L
A81L
A80R
A81R

860
A81A
860
863

858
852
857
853 856

862

855

861
865L
851
865R

854 859

Copyright © 2008 LG Electronics. Inc. All right reserved. 2-5 LGE Internal Use Only
Only for training and service purposes
• PACKING ACCESSORY VIEW

808 Battery 811 Plug Ass'y, 1Way

900 Remote Control 824 Antenna Loop

825 Antenna
801 Instruction Ass'y

818 Portable in Cable

803 Packing

803 Packing

804 Bag

802 Box

LGE Internal Use Only 2-6 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
 SECTION 3. ELECTRICAL PART
AUDIO ELECTRICAL TROUBLESHOOTING GUIDE
1. MICOM PART CHECK I

MICOM PART
HECK I

YES

Check NO Refer to SMPS

CN101 6PIN
troubleshooting.
P-SENS.

YES

Check Check if Check the

power of both NO IC101 KIA7042 NO NO Replace the
related part of IC101
terminals of IC101 input is over 5V. related parts.
KIA7042.
KIA7042

YES YES YES

Check IC100 Check if output voltage

LC87F5NC8A 4 PIN of IC101 KIA7042 is
power. 4.3V.

YES YES

OK OK

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-1 LGE Internal Use Only
Only for training and service purposes
2. MICOM PART CHECK II

MICOM PART CHECK II

YES

NO Refer to SMPS
Check CN101 5PIN 5.6V
Troubleshooting.

YES

Check power NO Check D101 RS1G

of both terminals of D101
output is working on 5V.
RS1G.
YES

NO
Check the related part Replace the related parts.

YES

OK

YES

Check Q10 NO
Check Q102 BASE NO Check output power of IC101
EMITTER 5V and
COLLECTOR 5V PIN 0.6V HIGH KIA7042 is over 4.3V.

YES
YES YES
Check IC103 8PIN IC100 NO
Check Q102 COLLECTOR Check the related part.
14,55,89 PIN 5V
YES YES

OK
YES
Check the working condition NO
X100:32.768kHz Check the
Replace the related parts.
X101:9.8304MHz related part.

YES YES

OK OK Replace the related parts.

LGE Internal Use Only 3-2 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
3. IC103 S-24CS16A01 PART CHECK

CHECK IC100 LC87F5NC8A

81,82 PIN
YES

NO NO Refer to micom
81 PIN DATA 82 PIN CLK Check MICOM power 5V troubleshooting.

YES
YES

NO
Check the related part. Replace the related parts.

YES

OK OK

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-3 LGE Internal Use Only
Only for training and service purposes
4. FLD DISPLAY PART CHECK

FLD DISPLAY CHECK

YES

Check NO Refer to SMPS

CN101 1,2,3 power. Troubleshooting

YES
F1+,F2-both terminals:over
3.7V Check power VKK:over
-28V.
YES Check P3101 assembly

YES
Check
P3101 connection
condition and power F1+,F2- NO Check NO
both terminals:over 3.7V power of each PIN. Replace the related part
Check power VKK:over -28V
Check 4,5 PIN:5.6V
YES

YES OK

Check
IC304 PT6324 NO When 5V fails,check D321SR35
power 50 PIN VKK:-28V input and output power.
9.52 PIN +5V YES

NO
Replace the related part.
Check the related part
YES
YES

OK
IC100
Check→IC304
Data communication. IC100 27 PIN→STB
PIN PIN NO 28 PIN→1PIN CLK
27PIN→3PIN STB Check Data output.
26PIN→2PIN DO
28PIN→1PIN CLK YES
Check 26 PIN→DO
→DATA input.
YES
YES

NO
FLT light on? Check the related part Replace the related part.

YES YES
OK OK

LGE Internal Use Only 3-4 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
5. TOUCH-PAD PART CHECK

TOUCH-PAD CHECK

YES

IC3A1 NO NO Refer to SMPS

PN3A2 1PIN 5V. Troubleshooting.
28PIN check 5V.
YES
YES
OK

Check NO NO
IC3A1 8Pin,9Pin, Check resistance output of
IC100 97Pin :CLK, Replace the related part.
line CLK :R3A2 DATA :R3A3
96Pin :DATA
YES YES

OK OK

6. PWM MODULATION PART CHECK

PWM MODULATION
PART CHECK
YES
Check NO Refer to SMPS
PN102 10PIN 3.3V.
Troubleshooting.

YES
Check IC702 PS9830 VDD
PIN power (3,10,22,29,39,47,
56,65,72,87,94)Check X701
2PIN 3.3V
YES

Check if X701 NO Check the NO

12.288MHz is working. related part of Replace the related part.
X701.
YES
YES
OK

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-5 LGE Internal Use Only
Only for training and service purposes
 YES

Check IC702 PS9830 Check R791(1M)output Replace the related part.

86 PIN CLK input NO NO

YES YES

OK

Check
output of IC100 Check
LC87F5NC8A NO resistance output of LINE NO
21→PWM_CLK DATA:R797 Replace the related part.
22→PWM_DATA CLK:R795
43→PWM_REST RST:R790
YES
YES
OK

Check IC702 Check DVD

PS9830 DATA input NO ASS`Y PS9830 NO
78 PIN→DATA Refer to DVD Troubleshooting.
79 PIN→CLK communication condition
96 PIN→REST (P7403)

YES YES

Check IC702 NO Check resistance

PS9830 DATA input. output of each LINE.

YES

OK

Check
PWM MODULATOR NO
output Check IC702 PS9830 part.
FL:75(+)74(-)
R:71(+)70(-)

YES

OK

LGE Internal Use Only 3-6 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
7. PWM AMP PART CHECK

POWER AMP PART CHECK

YES

PN102 NO
Refer to SMPS Troubleshooting.
3PIN + 13,14,15 PIN 28V.

YES

Check input power IC700

34,29,26,21 PIN.

YES

Check input power of IC700, NO Check resistance power

1,36,17,18,19 PIN +12V IC700:R702,701,726,727,724.

YES

Check PWM MODULATOR

input 4,6,14,16 PIN.

YES

Check POWER IC 700 34,

29,27,20 PIN output.

YES

NO
Check output LINE COIL. Replace the related parts.

YES

OK

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-7 LGE Internal Use Only
Only for training and service purposes
8. TUNER FUNCTION PART CHECK

TUNER FUNCTION PART CHECK

YES

Check TUNER NO Check TUNER MODUEL

module(TU100)is working. power(Check 4PIN 9V).

YES

Check IC201(CS5345)
26,27PIN input waveform.

YES

Check IC201(CS5345) NO Check IC201(CS5345)

14PIN output waveform. 5,14,30:5V 36,46,:3.3V

YES
YES

OK Replace the related parts

LGE Internal Use Only 3-8 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
9. SMPS POWER CIRCUIT

MAIN PART

MAIN PART

YES

Check the FUSE NO

Replace the fuse.
F901.

YES

Check
the DC V of C905 NO
Check BD901,LF901,902.
if DC V is over
400V.

YES

Check the
DC V of C909,C903,C921 NO NO
Check IC901,902. Replace IC901,902.
If DC V is in 14~19V
And it is steady

YES
YES
Check short of P9701,P9702 line.

Check the NO
DC V of C981,C945. Check short of P9702 line.
If DC V is 6.1V.

YES

Check the
DC V of C950,C951 NO
Check short of P9701 line.
If DC V is in
29V.

YES

OK

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-9 LGE Internal Use Only
Only for training and service purposes
P-SENS VKK PART CHECK

P-SENS VKK CHECK

YES YES

Check Check
NO Check power circuit the PIN3 of P9702 NO Check power circuit
the PIN6 of P9702
if DC V is over Troubleshooting. if DC V is over Troubleshooting.
5.6V -30V ±1.

YES YES

OK OK

10. IPOD PART(ONLY NORTH AMERICA)

TURN ON IPOD

YES

NO
LOADING Check the JK3C1 13pin, 30pin.

YES
YES

Check the JK3C1 13pin and 30pin line.

YES

OK

NO
OSD IPOD Check the JK3C1 18pin, 19pin.

YES
YES

Check theJK3C1 18pin and 19pin line

OK

YES

OK

LGE Internal Use Only 3-10 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
 DVD ELECTRICAL TROUBLESHOOTING GUIDE
1. POWER CHECK GUIDE

POWER ON

YES

Select the DVD Mode

YES

Does DVD NO Does it NO

appear DVD ERROR at Check an Audio Micom
appear at FLD?
FLD?

YES
YES
Check Connector
(P4405,P4407,P4408).

YES

Reconnect it.

Does No DISC or NO Check the voltage

Time are appeared at of each pin on PN102.
FLD?
YES
YES
Check DVD MD Module.
OK

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-11 LGE Internal Use Only
Only for training and service purposes
2. TEST & DEBUG FLOW

POWER ON

YES

NO NO Check connection lines between

Show LOGO? Flash Memory FLASH & ES8390 or the FLASH
operates properly? access time whether is suitable or not.

YES YES

Check connection lines between

NO SDRAM.
SDRAM works
properly? (IC502) & ES8390 or the SDRAM is
damaged.

YES

NO Check the related circuit of

ES8390 VIDEO ES8390 (IC501)
outputs properly? PIN80,83,84,85

YES

Check AV cable connection

to TV set.

Does DISC was NO NO

inserted inside when SW5 & SW7 signals
on PN4402 are OK? Check the MD mecha
you push Disc1~5
button?

YES YES

OPEN / CLOSE NO Check the output signal of

signals on IC401 are ES8390 to IC401 for control
OK? OPEN/CLOSE.

YES

NO Check the Tray control I/O

Load+ & load- signals
on PN4402 are OK? Pin on IC401.

YES

Check the cable connection between

A DVD PCB and MD (MECHA).

LGE Internal Use Only 3-12 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
 A

YES

Does the NO Motor Drive

SLED move to inner side YES
DRV_MUTE pin Check the MD
when it is at outer
position? is high?

YES YES

YES Check the related circuit of SLED

SLED signal is OK? and Motor driver IC ( IC401)

YES

Do not put in disc and Check the cable connection

tray close. with MECHA.

YES

Optical Proper
Lens is moving NO NO Check Focus connection on
Focus outputs
for searching Focus? to motor driver? ES8390 and motor driver IC.

YES YES

NO
Proper F+ & F-outputs? Check the motor driver (IC401).

YES

Check cable connection

B with pick-up head.

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-13 LGE Internal Use Only
Only for training and service purposes
 B

YES

Laser turns on NO NO Check the laser power circuit between

when reading DVDLD or CDLD
output properly? ES8390 and power transistor.
disc?
(Q405, Q406)

YES YES

Collector
voltage of power transistor NO Check the related circuit of laser
is ok? (Q405, Q406) power transistor.

YES

Check cable connection

between PN4401 and pick-up head.

NO
Put disc in SLOT. Laser off.

YES

NO NO
Does SPINDLE Proper SPINDLE Check the SPINDLE related
rotate? signal on ES8390. circuit on ES8390

YES YES

NO Check the SPINDLE control of

SPIN+&SPIN- output
properly? motor driver IC401.

YES

Check the cable connection

C between PN4401 and MD.

LGE Internal Use Only 3-14 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
 C

YES

NO NO Check the connections between

Proper signal on
Focus On OK? PN4401 and pick-up head.
A,B,C,D from MD?

YES YES

NO Check the related circuit of

Proper FOD signal on
IC401? ES8390 FOCUS signal.

YES

Check cable connection

between PN4401 and MD.

NO NO
Proper TRD signal on Check the related circuit
Tracking OK?
IC401? between IC401 and ES8390.

YES YES

NO Check the Tracking control

T+ & T- output
properly? on motor driver (IC401).

YES

Check cable connection on

pick-up head.

NO
Disc play? Check RF signal waveform.

YES

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-15 LGE Internal Use Only
Only for training and service purposes
 D

YES

All
outputs are Ok NO NO Check the SERIAL RESISTOR
Audio signal data on
during playing between ES8390 and IC702.
ES8390 is OK?
DISK ?

YES YES

Check the IC702.

For example composite video ,

NO Picture NO Check the video mute TR
TEST END signal data on (Q501), Output of Video buffer
ES8390 is OK? IC (IC507) and ES8390
video signal data.

LGE Internal Use Only 3-16 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
3. USB PART

TURN ON USB

YES

"Checking" or NO Check the POWER supply circuit.

"USB" Display check. (Check PN102)

YES YES

Check the HRST#signal.

YES

Check the HRST#signal.Check the USB PART

and DVD PART line.

NO Check the USB JACK POWER supply.

Reading OK check. (Check PN205)

YES YES

Check the USB DATA LINE. (PN205)

YES

Check the ES8390.

OK
Check DATA LINE PIN 91(USB-No)90(USB-Po)

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-17 LGE Internal Use Only
Only for training and service purposes
LGE Internal Use Only 3-18 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
 WAVEFORMS OF MAJOR CHECK POINT
1. WHEN POWER ON, RESET & DATA ETC WAVEFORM

RESET(DVD)
1

SPI_CS3
2

DI
3 1

DO
4

2
3 4

2. WHEN USB FUNCTION OPERATING

5V
2 1

D+
1

D-

2
IC501

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-19 LGE Internal Use Only
Only for training and service purposes
3. OPEN/CLOSE WAVEFORM AT POWER ON (OPEN AND CLOSE)

OPEN(High/Low) 1 2
1

CLOSE(Low/Low)

IC501

4. STARTING ACTION WAVEFORM IN MD DEVICE (SLED HOME)

SLO (from MPEG)

1
SLED-

2
SLED+ IC501

3 1

3
2

LGE Internal Use Only 3-20 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
5. FOCUS WAVEFORM (IN CASE OF CD) FOCUS WAVEFORM (IN CASE OF CD-RW)

TE
1 TE 1

PI PI

2 2
FOD FOD
3 3
FE FE
4 4

FOCUS WAVEFORM (IN CASE OF DVD5) FOCUS WAVEFORM (IN CASE OF DVD-RW)

TE
1
1 TE

PI
PI
2 2 FOD
3 FOD 3
TE
4 TE 4

4 2

1 IC501

IC501

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-21 LGE Internal Use Only
Only for training and service purposes
6. WHEN DISC READING , SPINDLE KICK SIGNAL
(SPNN &SPNP BE USED SPINDLE BREAK DIRECTION)
SPNN

1
SPNN
2
3 SPD

TE

WHEN WE PUSH OPEN OR STOP KEY ,SPIDLE BREAK SIGNAL

(SPNN &SPNP BE USED SPINDLE BREAK DIRECTION)

SPNN
1
SPNN
2

SPD
3

TE
4

2 1

4
3 IC501

IC501

LGE Internal Use Only 3-22 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
7. DVD & CD DISTINCTION
(DISC SURFACE & DATA LAYER DISTANCE IS DIFFERENT) IN CASE OF CD 30MS

3 1
Mirror

PI
1
FOD
2
SPNN
3

IC501

IC501

8. DVD & CD DISTINCTION

(DISC SURFACE & DATA LAYER DISTANCE IS DIFFERENT) IN CASE OF DVD 14MS

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-23 LGE Internal Use Only
Only for training and service purposes
9. AT FIRST ACTION, FOCUS SIGNAL A,B,C,D

A
1 1 2
B IC501
2
3
C
3
4
D
4

10. RF WAVEFORM (ANALOG SCOPE)

F+

LGE Internal Use Only 3-24 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
 WIRING DIAGRAM

1page MD

9PIN

18PIN

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-25 LGE Internal Use Only
Only for training and service purposes
 FRONT PCB
1page MD
SPK FL+
12.288MHZ
VFD SPK FL-

LGE Internal Use Only

SPK FR+

TAS53X2
FL+/FL-

TAS53X2
`` SPK FR-
TOUCH PCB FR+/FR-
PT6324
PT6324 RCU
RCU PICK_UP PWM
DRVER
PICK_UP PWM
DRVER
IC
IC
9830B
9830B

LOAD-/+,SPIN-/+
SLED-/+(6)
MOTOR
MOTOR
DRV.
DRV. IC
IC
IP9010
IP9010 BUFFER
BUFFER
USB POT HDP MC4580
MC4580
MIC

SDRAM
SDRAM
BLOCK DIAGRAM

FLASH
FLASH
BCK,LRCK, ADTA0,ADATA3

HP_L/R

CD_DVDCT,VC,DVDMDI,CDLDO,DVDLDO(5)
AMP_SD/PROTECT
FAN EEPROM
EEPROM

RF,PUDET,F,E,A,D,C,B,LOAD_SW1/SW2(10)

SLO,SPINO,OPEN,
CLOSE,FOO,TRO,
DRV_MUTE,SVREF(8)
SPNN,SPNP(2)
PWM_CLK,DAT,RST,AMP_PDN

MIC_SIG

PORT_L/R

USB_N,P
HP_L/R
Composite
Composite Y, Pb, Pr (4)
Y, Pb, Pr (4) COMP.
VIDEO
VIDEO

3-26
27MHZ
DRIVER
DRIVER Y Pr Pb
BH7868
BH7868
9.8304MHZ L R C

FAN_CTL
VFD_DO,VFD_STB,VFD_CLK
RCU,TOUCH_CLK,TOUCH_DAT
STBY_LED,KEY,H/P_SENS,
MIC_VOL,,MIC_DET
SERVO AUX
PART SCART JACK PCB
DVD RST(1)
R,G,B,V

VIDEO
DVD_DI_DO_CLK (3)
-COM MPEG
MPEG PART
-COM
CLK sanyo ESS8390 SCART
sanyo ESS8390
EEPROM IPOD_RX, TX
EEPROM DAT 100PIN
100PIN

AUDIO PART

MCLK,BCK,LRCK,
IPOD ADTAT
IPOD_VIDEO,

IC
IPOD_L/R,

P_CTL (1)
AUX_L/R,

RST IC
TUNER

RST
PORT_L/R,

FL-
FL+
VKK
SCART_L/R,

+5.6VA
BT_L/R,
ADC

+5V
3.3V
TUNER_L/R

-12V

+36V
+12V
CS5345
ADC_CLK, DAT,

P_SENS(1)
SMPS TUNER_DI,DO,CE,,MUTE,RDS_CLK,DAT / HDRADIO_RX, TX

Only for training and service purposes

Copyright © 2008 LG Electronics. Inc. All right reserved.
 CIRCUIT DIAGRAMS IMPORTANT SAFETY NOTICE COMPONENTS ARE SHADED ON THE SCHEMATIC NOTE :

1. SMPS(POWER) CIRCUIT DIAGRAM WHEN SERVICING THIS CHASSIS, UNDER NO CIR-

FOR EASY IDENTIFICATION.
THIS CIRCUIT DIAGRAM MAY OCCASIONALLY DIF-
1. Shaded( ) parts are critical for safety. Replace only
with specified part number.
CUMSTANCES SHOULD THE ORIGINAL DESIGN BE FER FROM THE ACTUAL CIRCUIT USED. THIS WAY, 2. Voltages are DC-measured with a digital voltmeter
MODIFIED OR ALTERED WITHOUT PERMISSION IMPLEMENTATION OF THE LATEST SAFETY AND during Play mode.
FROM THE LG CORPORATION. ALL COMPONENTS PERFORMANCE IMPROVEMENT CHANGES INTO
SHOULD BE REPLACED ONLY WITH TYPES IDENTI- THE SET IS NOT DELAYED UNTIL THE NEW SERVICE
CAL TO THOSE IN THE ORIGINAL CIRCUIT. SPECIAL LITERATURE IS PRINTED.

12

11

10

NOTES) Symbol denotes DC chassis ground.

1 NOTE) Warning
NOTE) Parts that are shaded are critical
NOTE)
NOTE)
With respect to risk of fire or
electricial shock. 2008.02.19
A B C D E F G H I J K L M N O P Q R S T

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-27 3-28 LGE Internal Use Only
Only for training and service purposes
2. MICOM CIRCUIT DIAGRAM

12

11

10

2008.02.19
A B C D E F G H I J K L M N O P Q R S T

LGE Internal Use Only 3-29 3-30 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
3. MPEG CIRCUIT DIAGRAM

12

11

10

2008.02.19
A B C D E F G H I J K L M N O P Q R S T

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-31 3-32 LGE Internal Use Only
Only for training and service purposes
4. SERVO CIRCUIT DIAGRAM

12

11

10

2008.02.19
A B C D E F G H I J K L M N O P Q R S T

LGE Internal Use Only 3-33 3-34 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
5. I/O CIRCUIT DIAGRAM

12

11

10

2008.02.19
A B C D E F G H I J K L M N O P Q R S T

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-35 3-36 LGE Internal Use Only
Only for training and service purposes
6. AMP CIRCUIT DIAGRAM

12

11

10

2008.02.19
A B C D E F G H I J K L M N O P Q R S T

LGE Internal Use Only 3-37 3-38 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
7. SCART CIRCUIT DIAGRAM

12

11

10

2008.02.19
A B C D E F G H I J K L M N O P Q R S T

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-39 3-40 LGE Internal Use Only
Only for training and service purposes
8. FRONT CIRCUIT DIAGRAM

12

11

10

2008.02.19
A B C D E F G H I J K L M N O P Q R S T

LGE Internal Use Only 3-41 3-42 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
9. TOUCH KEY CIRCUIT DIAGRAM

12

11

10

2008.02.19
A B C D E F G H I J K L M N O P Q R S T

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-43 3-44 LGE Internal Use Only
Only for training and service purposes
10. MIC CIRCUIT DIAGRAM

12

11

10

2008.02.19
A B C D E F G H I J K L M N O P Q R S T

LGE Internal Use Only 3-45 3-46 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
 INTERNAL BLOCK DIAGRAM OF IC
• PS9830B

1) PIN CONFIGURATION

PWM8_M

PWM7_M

PWM6_M

PWM5_M

PWM4_M

PWM3_M

PWM2_M
PWM8_P

PWM7_P

PWM6_P

PWM5_P

PWM4_P

PWM3_P

PWM2_P
IO_VDD

IO_VDD

IO_VDD
IO_VSS

IO_VSS

IO_VSS

IO_VSS

IO_VSS

IO_VSS
DVDD

DVSS
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
OVERLOAD 76 50 IO_VSS
EPD_ENA 77 49 PWM1_P
SO/SDA 78 48 PWM1_M
SCK/SCL 79 47 IO_VDD
DVDD 80 46 PWM_HP_L_P
DVSS 81 45 PWM_HP_L_M
SI/I2C_AD0 82 44 IO_VSS
/CS/I2C_AD2
SPI/I2C
IO_VSS
XIN
83
84
85
86
PULSUS 43
42
41
40
DVSS
DVDD
PWM_HP_R_P
PWM_HP_R_M
XOUT 87 39 IO_VDD

PS9830B
DMIX_LRCK 88 38 IO_VSS
DMIX_BCK 89 37 PWM_SWL_P
DMIX_SDOUT 90 36 PWM_SWL_M
DVDD 91 35 DVSS
DVSS 92 34 DVDD
DMIX_MCLK 93 33 MIC_SDIN
IO_VDD 94 32 MIC_LRCK
IO_VSS 95 31 MIC_BCK
/RESET 96 30 MIC_MCLK
TEST_MODE1 97 29 IO_VDD
TEST_MODE2 98 28 IO_VSS
SCAN_ENA 99 27 EXT_MUTE
TEST_MODE3 100 26 SSDIN3
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
1
2
3
4
5
6
7
8
9

MSDIN0
MSDIN1
MSDIN2
MSDIN3
PLL_AVSS

DVSS

SSDIN0
SSDIN1
SSDIN2
PLL_DVSS
IO_VSS

PLL_AVDD
IO_VSS

IO_VSS

MLRCK

SBCK
SLRCK
IO_VSS
IO_VDD

MBCK

DVDD
IO_VDD

IO_VDD
PLL_DVDD

IO_VSS

2) BLOCK DIAGRAM

MBCK
MLRCK Input
MSDIN[0:3] Serial Audio
&
Output
Output
SBCK interface
MUX
SLRCK
SSDIN[0:3]
Serial DMIX_MCLK
Down Audio OLRCK
Sample OBCK
Mixer Output
Rate interface DMIX_SDOUT
Converter
Automatic
Gain PWM1_P/M
Limiter
Input PWM2_P/M
Mapper
Output Mapper

PWM3_P/M
PWM4_P/M
Bass Main Trim
Mixer EQ PWM5_P/M
MIC_MCLK Manager Volume Volume
Mic. PWM6_P/M
MIC_BCK
Input
MIC_LRCK PWM7_P/M
Processor
MIC_SDIN PWM PWM8_P/M
Modulator
Internal Clock Internal Reset PWM_HP_L_P/M
SPI/I2C
SO/SDA PWM_HP_R_P/M
SCK/SCL Host
Internal Controls Reset & Power Down
SI/I2C_AD0 Interface PWM_SWL_P/M
/CS/I2C_AD2 (I2C, SPI)
POP EPD_ENA
EXT_MUTE Crystal Power Supply
PLL NR
Oscillator OVERLOAD
XI N

OXUT

/RESET

PLL_DVDD

PLL_AVDD
PLL_DVSS

PLL_AVSS

IO_VDD
IO_VSS
DVDD
DVSS

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-47 LGE Internal Use Only
Only for training and service purposes
3) PIN DESCRIPTIONS
Name Pin NO. Type Description
Power and Ground
PLL_AVDD 6 Analog PLL analog power supply.
Power
PLL_AVSS 8 Analog PLL analog ground.
Ground
PLL_DVDD 3 PLL PLL digital power supply.
Power
PLL_DVSS 2 PLL PLL digital ground.
Ground
DVDD 13, 34, 42, Power Core power supply.
66, 80, 91
DVSS 14, 35, 43, Ground Core digital ground.
63, 81, 92
IO_VDD 4, Power I/O power supply. 3.3V Digital power supply.
10, 22, 29, 39, 47,
56, 65, 72, 94
IO_VSS 1, 5, 7, 9, 21, Ground I/O digital ground.
28, 38, 44, 50,
53, 57, 60, 64,
69, 73, 85, 95
Reset and Clock
/RESET 96 I H/W reset signal. Active Low Schmitt-Trigger input.
The Schmitt-Trigger input allows a slowly rising input to reset the
chip reliably. The RESET signal must be asserted ‘Low’ during
power up. De-assert ‘High’ for normal operation.
XIN 86 Analog Crystal Oscillator input pin.
XOUT 87 Analog Crystal Oscillator output pin.
PCM Audio Input/Output Interface
MBCK 11 I/O PCM bit clock input/output of main 8-channel audio.
User can select the master/slave mode of this signal.
Schmitt-Trigger input.
MLRCK 12 I/O PCM Word clock (left-right clock) input/output of main 8-channel
audio. User can select the master/slave mode of this signal.
Schmitt-Trigger input.
MSDIN [3:0] 15, 16, 17, 18 I PCM serial data input of main 8-channel audio.
Schmitt-Trigger input.
SBCK 19 I/O PCM bit clock input/output of 8-channel audio.
User can select the master/slave mode of this signal.
Schmitt-Trigger input.
SLRCK 20 I/O PCM word clock (left-right clock) input/output of sub 8-channel
audio. User can select the master/slave mode of this signal.
Schmitt-Trigger input.
SSDIN [3:0] 23, 24, 25, 26 I/O PCM serial data input of sub-channel audio.
User can set this sub-channel data input pins to PCM serial data
output pins. See the Control Register Descriptionpart.
Schmitt-Trigger input

LGE Internal Use Only 3-48 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
 MIC_MCLK 30 O Main clock for external microphone input A/DC.
Clock frequency can be selected between 6.144MHz,
12.288MHz, and 24.576MHz.
MIC_BCK 31 I/O PCM bit clock input/output of external microphone.
Bit clock frequency is 3.072MHz (48kHz x 64, fixed)
MIC_LRCK 32 I/O PCM Word clock (left-right clock) input/output of external
microphone. Word clock rate is 48kHz (fixed).
MIC_SDIN 33 I PCM serial data input of external microphone.
Schmitt-Trigger input.
DMIX_MCLK 93 O Main clock for external down-mix line output D/AC.
DMIX_BCK 89 O PCM bit clock output of down-mix signal.
Bit clock frequency is 6.144MHz (96kHz x 64, fixed)
DMIX_LRCK 88 O PCM Word clock (left-right clock) output of down-mix signal.
Word clock rate is 96kHz (fixed).
DMIX_SDOUT 90 O PCM serial data output of down-mix signal.

PWM Audio Output

PWM1_P 49 O Positive PWM output of channel 1.
PWM1_M 48 O Negative PWM output of channel 1.
PWM2_P 52 O Positive PWM output of channel 2.
PWM2_M 51 O Negative PWM output of channel 2.
PWM3_P 55 O Positive PWM output of channel 3.
PWM3_M 54 O Negative PWM output of channel 3.
PWM4_P 59 O Positive PWM output of channel 4.
PWM4_M 58 O Negative PWM output of channel 4.
PWM5_P 62 O Positive PWM output of channel 5.
PWM5_M 61 O Negative PWM output of channel 5.
PWM6_P 68 O Positive PWM output of channel 6.
PWM6_M 67 O Negative PWM output of channel 6.
PWM7_P 71 O Positive PWM output of channel 7.
PWM7_M 70 O Negative PWM output of channel 7.
PWM8_P 75 O Positive PWM output of channel 8.
PWM8_M 74 O Negative PWM output of channel 8.
PWM_HP_L_P 46 O Positive PWM output of headphone left channel.
PWM_HP_L_M 45 O Negative PWM output of headphone left channel.
PWM_HP_R_P 41 O Positive PWM output of headphone right channel.
PWM_HP_R_M 40 O Negative PWM output of headphone right channel.
PWM_SWL_P 37 O Positive PWM output of subwoofer line output.
PWM_SWL_M 36 O Negative PWM output of subwoofer line output.

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-49 LGE Internal Use Only
Only for training and service purposes
4) SPECIFICATIONS

Parameter Min Max Units

Power Supply Voltage (IO_VDD) - 0.5 4.0 V

Power Supply Voltage* (DVDD, PLL_AVDD, PLL_DVDD) V

Output Current (/Pin) - 25 mA

Input Voltage VSS – 0.5 5.5 V

Storage Temperature -65 +150 °C

Stresses greater than those listed over Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating
only; functional operation of the device at these or any other conditions above those indicated in the operational section of this
specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

The *power supply voltage (DVDD, PLL_AVDD, PLL_DVDD) is supplied by internal regulator.

RECOMMENDED OPERATING CONDITIONS

Parameter Min Typ Max Units

Power Supply Voltage (IO_VDD) 2.97 3.3 3.63 V

Supply Current (IO_VDD = 3.3V) - 160 - mA

Input Voltage - 0.3 - 5.5 V

Ambient Operating Temperature -20 25 75 °C

ELECTRICAL CHARACTERISTICS

Parameter Min Typ Max Units

Input Leakage Current
- - 10 µA
(except Pull-up, Pull-down Input)
High-Level Input Voltage (except Schmitt Input) 2.0 - 5.5 V
Low-Level Input Voltage (except Schmitt Input) -0.3 - 0.8 V
VT+(Schmitt trigger positive threshold voltage) 1.44 1.5 1.56 V
VT-(Schmitt trigger negative threshold voltage) 0.89 0.94 0.99 V
High-Level Output Voltage (IO = 24mA) 2.4 - - V
Low-Level Output Voltage (IO = 24mA) - - 0.4 V
Pull-up Resistance 39 65 116 kΩ
Pull-down Resistance 40 56 108 kΩ
Input Capacitance (f = 1MHz, VDD = 0V) - - 10 pF
Output Capacitance (f = 1MHz, VDD = 0V) - - 10 pF
Low Level output current @Vol=0.4V 2mA 2.4 4.0 5.0 mA
4mA 4.7 8.0 10.0
High Level output current @Voh=2.4V 2mA 2.8 5.9 9.5 mA
4mA 5.6 11.9 19

LGE Internal Use Only 3-50 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
• LC87F5NC8AVU

1) PIN CONFIGURATION

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-51 LGE Internal Use Only
Only for training and service purposes
2) BIOCK DIAGRAM

LGE Internal Use Only 3-52 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
3) PIN DESCRIPTIONS

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-53 LGE Internal Use Only
Only for training and service purposes
LGE Internal Use Only 3-54 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
• ES8391

1) PIN CONFIGURATION

TSD3/PWM_O3R/DAC_O3R

TSD1/PWM_O2R/DAC_O2R
TBCK/PWM_01R/DAC_O1R
TSD2/PWM_O3L/DAC_O3L

TSD0/PWM_O2L/DAC_O2L
TWS/PWM_O1L/DAC_O1L
SPNP/MNTRP/IMSR
SPNN/MNTRN

CLOSESW

ADC_BIAS
AMPSTBY
OPENSW

INV_OUT

USB_N0
USB_P0
AUX2[4]

VID_XO
DVDPD

DVDLD

CLOSE

VID_XI
V165O

MIC_R
SR[30]
SR[31]
SR[32]
SR[33]

SR[34]
SR[35]
SR[36]
SR[37]

AVD33
AVS33
MIC_L
OPEN

LDCO
CDLD
AGC1
AGC2

VD33

VD33
VS33

VS33
VDD
VGB
VBO

REX

VPB
MB
MP
DB
FE
TE
PI
162
161
160
159
158
157
156
155
154
153
152
151
150
149
148
147
146
145
144
143
142
141
140
139
138
137
136
135
134
133
132
131
130
129
128
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
VPA 163 108 VS33PLL
VGA 164 107 VD33PLL
DRFN 165 106 IDAC/YUV1
DRFP 166 105 UDAC/YUV0
A 167 104 CDAC/YUV2
B 168 103 YDAC/YUV5
C 169 102 VS33DAC
D 170 101 VD33DAC
E 171 100 VDAC/YUV6
F 172 99 FDAC/YUV7
G 173 98 RSET/YUV4
H 174 97 COMP/YUV3
MIN 175 96 VREF
SLV 176 95 VD33
DMO 177 94 VS33
FOO 178 93 AUX2[3]
SLO 179 92 SR[20]
TRO 180 91 SR[21]
CDPD 181 90 SR[22]
REFD 182 89 SR[23]
AVD33 183 88 SR[24]
AVS33 184 87 SR[25]
DVCC 185 86 SR[26]
VD33 186 85 SR[27]
VS33 187 84 CLK/TDMCLK/RBCK
VDD 188 83 RESET#
SIN 189 82 MCLK
SOUT
AUX2[5]
190
191
ES8391 81
80
AUX3[0]/CAMIN0
AUX3[1]/CAMIN1
SR[10] 192 79 VDD
SR[11] 193 78 VS33
SR[12] 194 77 VD33
SR[13] 195 76 AUX3[2]/CAMIN2
SR[14] 196 75 AUX3[3]/CAMIN3
SR[15] 197 74 AUX3[4]/CAMIN4
SR[16] 198 73 AUX3[5]/CAMIN5
SR[17] 199 72 AUX3[6]/CAMIN6
AUX2[6] 200 71 AUX3[7]/CAMIN7
DMA4 201 70 AUX2[3]
DMA5 202 69 AUX15/656CLK
VD33 203 68 AUX14/TBCK/TXD1
VS33 204 67 AUX13/RWS/TDMFS
DMA6 205 66 AUX12/RBCK/TDMCL
DMA7 206 65 AUX11/RSD/TDMDR
DMA8 207 64 AUX10/TSD[3]
DMA9 208 63 AUX9/HSYNC/TXD2
DMA11 209 62 VD33
DMA3 210 61 VS33
DMA2 211 60 AUX8/VSYNC/RXD2
DMA1 212 59 SPDIF_OUT
DMA0 213 58 SPDIF_IN
DMA10 214 57 SPI_DO
DRAS2# 215 56 SPI_DI
DRAS1# 216 55 SPI_CLK
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
1
2
3
4
5
6
7
8
9
VS33
DCS1#

SPI_CS2
SPI_CS3
AUX2[0]
SR[00]
SR[01]
SR[02]
SR[03]
SR[04]
SR[05]
SR[06]
SR[07]
AUX2[1]
VD33

DCS0#
DRAS0#/SEL_PLL2

VS33
DCAS#/SEL_PLL3

DB4
DB3
DB2
DB1
DB0
DB8
DB9
DB10
DB11
DB12
DB13
DB14
VS33
VD33
DB15

AUX7
AUX6
AUX5
AUX4
VD33
VS33
AUX3
AUX2
AUX1
AUX0
DOE#/SEL_PLL0
DWE#/SEL_PLL1

DB7
DB6
DB5
VD33
DQM
DSCK

VDD

VDD

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-55 LGE Internal Use Only
Only for training and service purposes
2) PIN DESCRIPTIONS
ES8391 Pin Description
Table 1 lists the pin descriptions for the ES8391.
Table 1 ES8391 Pin Description

Names Pin Numbers I/O Definitions

1, 14, 30, 46, 62,
VD33 77, 95, 119, 133, P I/O power supply.
186, 203
2, 15, 29, 47, 61,
VS33 78, 94, 120, 132, G Ground.
187, 204
DCS1# 3 O DRAM chip select 1 (active-low).
DCS0# 4 O DRAM chip select 0 (active-low).
DRAS0# 5 I/O DRAM row address strobes (active-low).
SEL_PLL2 I Strap pin: System and DSCK output clock frequency selection is made at the
rising edge of RESET#. The matrix below lists the available PLL bit settings.
Strapped to VD33PLL or VS33PLL via 4.7-kΩ resistor; read-only during reset.

SEL_PLL2 SEL_PLL1 SEL_PLL0 Clock Type (MHz)

0 0 0 Bypass
0 0 1 121.5MHz
0 1 0 128.25MHz
0 1 1 135MHz
1 0 0 141.75MHz
1 0 1 155.25MHz
1 1 0 162MHz
1 1 1 148.5MHz

SEL_PLL3 6 I Clock source select: Strapped to VD33PLL or VS33PLL via 4.7-k! resistor; read
only during reset.

SEL_PLL3 Clock Source

1 Crystal oscillator
0 CLK input

DCAS# O DRAM column address strobe (active-low).

SEL_PLL0 I Strap pin. Refer to the description and matrix for SEL_PLL2, pin 5.
7
DOE# O DRAM output enable (active-low).
DWE# O DRAM write enable (active-low).
8
SEL_PLL1 I Strap pin. Refer to the description and matrix for SEL_PLL2, pin 5.
DSCK 9 O Output clock to DRAM.
DQM 10 O Data input/output mask.
31, 28-22, 11-13,
DB[15:0] I/O DRAM data bus.
17-21
VDD 16, 48, 79, 124, 188 P Core power supply.
200, 191, 138, 93,
AUX2[6-0] I/O Aux2 data I/O 6-0.
70, 41, 32

LGE Internal Use Only 3-56 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
 Names Pin Numbers I/O Definitions
SR[00:07] 33-40 I/O Application specific pins. Refer to Table 2 for details.
AUX7-0 42-45, 49-52 I/O Auxiliary ports 7-0.
SPI_CS2 53 O SPI boot select.
SPI_CS3 54 O SPI bank-swap select.
SPI_CLK 55 O SPI clock.
SPI_DI 56 I SPI data input.
SPI_DO 57 SPI data output.
SPDIF_IN 58 IO S/PDIF input.
SPDIF_OUT 59 O S/PDIF output.
VSYNC# I/O Vertical sync (active-low).
RXD2 60 I Serial port 2 receive.
AUX8 I/O Auxiliary port 8.
HSYNC I/O Horizontal sync.
TXD2 63 O Serial port 2 transmit.
AUX9 I/O Auxiliary port 9.
TSD[3] O Audio transmit serial data (for down-mix).
64
AUX10 I/O Auxiliary port 10.
RSD I Audio receive serial data.
TDMDR 65 I TDM serial data.
AUX11 I/O Auxiliary port 11.
RBCK I/O Audio receive bit clock.
TDMCLK 66 I TDM bit clock.
AUX12 I/O Auxiliary port 12.
RWS I Audio receive frame sync.
TDMFS 67I TDM frame sync.
AUX13 I/O Auxiliary port 13.
TBCK I/O Audio transmit bit clock.
TXD1 68 O Serial port 1 transmit.
AUX14 I/O Auxiliary port 14.
656CLK O BT656 clock.
69
AUX15 I/O Auxiliary port 15.
AUX3[7] I/O Aux3 data I/O 7.
71
CAMIN7 I Camera input 7.
AUX3[6] I/O Aux3 data I/O 6.
72
CAMIN6 I Camera input 6.
AUX3[5] I/O Aux3 data I/O 5.
73
CAMIN5 I Camera input 5.

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-57 LGE Internal Use Only
Only for training and service purposes
 Names Pin Numbers I/O Definitions
AUX3[4] I/O Aux3 data I/O 4.
74
CAMIN4 I Camera input 4.
AUX3[3] I/O Aux3 data I/O 3.
75
CAMIN3 I Camera input 3.
CAMIN2 76 I Camera input 2.
AUX3[2] I/O Aux3 data I/O 2.
CAMIN1 I Camera input 1.
80
AUX3[1] I/O Aux3 data I/O 1.
CAMIN0 I Camera input 0.
81
AUX3[0] I/O Aux3 data I/O 0.
MCLK 82 I/O Audio master clock for audio DAC.
RESET# 83 I Reset (active-low).
RBCK I/O Audio receive bit clock.
TDMCLK 84 I TDM bit clock.
CLK I System clock.
SR[20:27] 85-92 I/O Application specific pins. Refer to Table 2 for details.
VREF 96 I Internal voltage reference to video DAC.
COMP I Compensation input.
97
YUV3 O YUV pixel 3 output data.
RSET I DAC current adjustment resistor input.
98
YUV4 O YUV pixel 4 output data.

LGE Internal Use Only 3-58 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
• IP9010

1) PIN CONFIGURATION

2) PIN DESCRIPTIONS

NO SYMBOL I /O DESCRI PTI ON NO SYMBOL I /O DESCRI PTI ON

1 DO1- O CH1 driver output(-) 15 DO4- O CH4 driver output(-)

2 DO1+ O CH1 driver output(+) 16 DO4+ O CH4 driver output(+)
3 DO2- O CH2 driver output(-) 17 DO5- O CH5 driver output(-)

4 DO2+ O CH2 driver output(+) 18 DO5+ O CH5 driver output(+)

5 VCC1 - Power supply voltage 1 19 VCC2 - Power supply voltage 2
6 IN2 I CH2 input 20 IN5 I CH5 input
7 IN1 I CH1 input 21 IN4 I CH4 input

8 MUTE I Mute 22 GND - Ground

9 CTL3 I Loading motor speed control 23 BIAS I Bias
10 REV3 I Loading motor reverse input 24 VDET I Reset detection
11 FWD3 I Loading motor forward input 25 RESET O Reset output
12 SVCC - Signal supply voltage 26 FB I Adjustable regulator feed back
13 DO3+ O CH3 driver output(+) 27 REGVCC O Regulator supply voltage
14 DO3- O CH3 driver output(-) 28 REO - Adjustable regulator output

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-59 LGE Internal Use Only
Only for training and service purposes
3) BIOCK DIAGRAM

LGE Internal Use Only 3-60 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
• TAS5342

1) TYPICAL SYSTEM BLOCK DIAGRAM

OTW
System
Microcontroller SD

TAS5518

OTW
SD
BST_A
Bootstrap
BST_B Capacitors
VALID RESET_AB
RESET_CD

PWM_A
OUT_A
Left- 2nd-Order L-C
Input Output
Channel Output Filter
H-Bridge 1 H-Bridge 1
Output OUT_B for Each
PWM_B
Half-Bridge

2-Channel
H-Bridge
BTL Mode

PWM_C OUT_C
2nd-Order L-C
Right- Output
Output Filter
Channel H-Bridge 2
Input OUT_D for Each
Output H-Bridge 2 Half-Bridge
PWM_D
GVDD_A, B, C, D
PVDD_A, B, C, D

M1
GND_A, B, C, D

BST_C
Hardwire M2
Mode Bootstrap
OC_ADJ

Control Capacitors
AGND

BST_D
VREG
GND
VDD

M3

4 4 4

PVDD GVDD
PVDD Power VDD
35.5 V Supply Hardwire
VREG
System Decoupling Power Supply OC Limit
Power Decoupling
Supply

GND
GND

GVDD (12 V)/VDD (12 V)

12 V

VAC

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-61 LGE Internal Use Only
Only for training and service purposes
2) FUNCTIONAL BLOCK DIAGRAM

4 VDD
Under-
OTW voltage 4
Protection
Internal Pullup VREG VREG
Resistors to VREG

SD
Power
On
M1
Reset AGND
Protection
M2 and
I/O Logic
M3 Temp.
Sense GND

RESET_AB
Overload
RESET_CD Isense OC_ADJ
Protection

GVDD_D
BST_D
PVDD_D
PWM Gate
PWM_D Ctrl. Timing OUT_D
Rcv. Drive
BTL/PBTLConfiguration
Pulldown Resistor

GND_D
GVDD_C
BST_C
PVDD_C
PWM Gate
PWM_C Ctrl. Timing OUT_C
Rcv. Drive
BTL/PBTLConfiguration
Pulldown Resistor

GND_C
GVDD_B
BST_B
PVDD_B
PWM Gate
PWM_B Ctrl. Timing OUT_B
Rcv. Drive
BTL/PBTLConfiguration
Pulldown Resistor

GND_B
GVDD_A
BST_A
PVDD_A
PWM Gate
PWM_A Ctrl. Timing OUT_A
Rcv. Drive
BTL/PBTLConfiguration
Pulldown Resistor

GND_A
B0034-03

LGE Internal Use Only 3-62 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
 CIRCUIT VOLTAGE CHART

PIN NO. EE Mode (V) PIN NO. EE Mode (V) PIN NO. EE Mode (V) PIN NO. VOLT PIN NO. EE Mode (V) PIN NO. EE Mode (V) PIN NO. EE Mode (V)

IC MAIN 62 0.29 24 0.02 87 1.76 13 1.9 76 3.37 38 1.5

IC 100 (audio Micom)LC87F5NC8A 63 0.57 25 0.02 88 1.69 14 0.001 77 3.44 39 0.04
1 1.31 64 0.64 26 0.02 89 1.68 15 0.03 78 4.98 40 1.19
2 0.35 65 2.03 27 0.001 90 1.68 16 1.69 79 4.98 41 3.4
3 0.21 66 2.08 28 0.001 91 1.9 17 1.68 80 1.9 42 3.4
4 3.81 67 2.09 29 3.44 92 0.002 18 1.76 81 0.001 43 3.19
5 0.86 68 2.14 30 1.67 93 1.66 19 1.68 82 0.001 44 3.19
6 1.09 69 0.01 31 1.71 94 3.44 20 1.71 83 0.001 45 3.29
7 4.44 70 5.52 32 1.71 95 0.002 21 0.001 84 0.001 46 0.96
8 5.02 71 5.01 33 0.01 96 5.01 22 3.44 85 0.001 47 0.65
9 2.34 72 3.23 34 1.9 97 0.002 23 0.029 86 1.71 48 3.4
10 2.54 73 3.9 35 0.001 98 0.002 24 0.029 87 1.71 49 0.09
11 0.01 74 2.04 36 1.71 99 0.002 25 0.029 88 1.69 50 4.08
12 2.45 75 2.12 37 1.71 100 0.002 26 0.001 89 1.89 51 0.01
13 2.55 76 2.11 38 0.001 IC703 (MC4580) 27 0.001 90 1.68 52 3.35
14 5.07 77 5.04 39 3.44 1 0.06 28 0.001 91 1.9 53 4.87
15 5.02 78 5.04 40 1.71 2 0.04 29 3.44 92 0.002 54 3.37
16 4.98 79 5.01 41 1.71 3 0.04 30 1.67 93 1.66 55 1.69
17 4.99 80 5.01 42 1.9 4 -12.23 31 1.71 94 3.44 56 1.65
18 4.9 81 5.04 43 0.001 5 0.04 32 1.71 95 0.001 57 1.7
19 0.01 82 5.04 44 0.001 6 0.06 33 0.001 96 5.01 58 1.65
20 0.9 83 4.22 45 1.71 7 0.06 34 1.9 97 0.001 59 3.38
21 0.83 84 0.01 46 1.71 8 11.58 35 0.001 98 0.001 60 3.38
22 4.98 85 0.02 47 3.44 IC704 (MSGEQ7N) 36 1.71 99 0.001 61 0.01
23 0.02 86 2.82 48 1.71 1 5.14 37 1.71 100 0.001 62 3.38
24 0.23 87 0.07 49 1.71 2 0.01 38 0.001 IC 501 Mpeg (ES8390) 63 3.38
25 3.37 88 0.01 50 0.001 3 0.4 39 3.44 1 3.37 64 1.36
26 5.03 89 5.04 51 1.71 4 0.04 40 1.71 2 0 65 3.38
27 5.03 90 0.12 52 1.71 5 2.2 41 1.71 3 0.22 66 3.38
28 5.03 91 0.12 53 0.001 6 2.58 42 1.9 4 3.26 67 0.01
29 4.64 92 0.1 54 1.71 7 0.08 43 0.001 5 3.2 68 1.5
30 0.01 93 0.03 55 1.71 8 2.54 44 0.001 6 3.3 69 3.37
31 0.01 94 2.27 56 3.44 IC103 (S24CS1) 45 1.71 7 3.46 70 3.38
32 0.01 95 2.08 57 0.001 1 0.01 46 1.71 8 0 71 1.65
33 0.01 96 4.74 58 1.71 2 0.01 47 3.44 9 1.45 72 4.29
34 5.03 97 4.82 59 1.71 3 0.01 48 1.71 10 0.02 73 1.8
35 0.01 98 0.01 60 0.001 4 0.01 49 1.71 11 0.92 74 0.01
36 5.03 99 0.01 61 1.71 5 5.04 50 0.001 12 0.94 75 3.35
37 0.01 100 0.01 62 1.71 6 5.04 51 1.71 13 0.86 76 0.02
38 5.04 IC 702 Pulsus (PS9830) 63 0.002 7 0.01 52 1.71 14 3.35 77 2.36
39 0.01 1 0.001 64 0.001 8 5.04 53 0.001 15 0 78 1.31
40 5.04 2 0.001 65 3.44 IC102 (KIA70) 54 1.71 16 1.5 79 3.38
41 0.32 3 1.93 66 1.9 1 5.04 55 1.71 17 0.71 80 0.94
42 0.39 4 3.46 67 1.71 2 0.01 56 3.44 18 0.91 81 3.35
43 0.01 5 0.001 68 1.71 3 5.03 57 0.001 19 0.71 82 0
44 0.01 6 1.95 69 0.001 IC101 (KIA70) 58 1.71 20 0.71 83 0.93
45 0.01 7 0.001 70 1.71 1 5.23 59 1.71 21 0.6 84 0.9
46 4.95 8 0.001 71 1.71 2 0.01 60 0.001 22 0.83 85 0.76
47 0.23 9 0.001 72 3.44 3 4.08 61 1.71 23 0.89 86 3.36
48 0.27 10 3.44 73 0.001 IC MAIN_AMP 62 1.71 24 0.77 87 3.4
49 0.26 11 1.79 74 1.71 IC 700 Pulsus (PS9830) 63 0.001 25 0.76 88 0.01
50 0.28 12 1.8 75 1.71 1 0.001 64 0.001 26 0.68 89 3.4
51 0.3 13 1.9 76 3.37 2 0.001 65 3.44 27 0.87 90 0.02
52 0.28 14 0.001 77 3.44 3 3.44 66 1.9 28 0.95 91 0.02
53 0.39 15 0.03 78 4.98 4 3.46 67 1.71 29 0 92 0.59
54 5.02 16 1.69 79 4.98 5 0.001 68 1.71 30 3.35 93 1.08
55 5.04 17 1.68 80 1.9 6 1.95 69 0.001 31 1.11 94 1.09
56 0.01 18 1.76 81 0.002 7 0.001 70 1.71 32 3.35 95 0
57 0.81 19 1.68 82 0.002 8 0.001 71 1.71 33 1.17 96 1.69
58 0.02 20 1.71 83 0.002 9 0.001 72 3.44 34 0.42 97 0.02
59 0.01 21 0.001 84 0.002 10 3.44 73 0.001 35 0.29 98 0.02
60 0.01 22 3.44 85 0.002 11 1.79 74 1.71 36 3.35 99 3.37
61 0.21 23 0.02 86 1.71 12 1.8 75 1.71 37 0.02 100 0.01

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-63 3-64 LGE Internal Use Only
Only for training and service purposes
 PIN NO. EE Mode (V) PIN NO. EE Mode (V) PIN NO. EE Mode (V) PIN NO. EE Mode (V) PIN NO. EE Mode (V) PIN NO. EE Mode (V) PIN NO. EE Mode (V)

101 0.02 164 0 3 0.15 51 0.95 6 5.03 20 -25.27 30 0.312

102 0.02 165 1.79 4 0.15 52 0.01 7 2.47 21 -27.05 31 0.312
103 1.68 166 1.38 5 0.15 53 1.11 8 2.49 22 -19.24 32 0.014
104 1.5 167 2.62 6 3.26 54 0.01 9 2.47 23 -19.37 IC 303 (BA3308)
105 1.81 168 0 7 0 IC503 10 2.49 24 -25.31 1 1.74
106 1.75 169 0.02 8 3.48 1 3.16 11 0.49 25 -23.55 2 0.008
107 0.01 170 1.6 9 2.58 2 1.65 12 0.22 26 -18.38 3 1.74
108 3.35 171 0.56 10 2.49 3 3.4 13 0.01 27 -20.04 4 0.008
109 0.01 172 0.55 11 3.48 4 0.01 14 4.96 28 -27.2 5 0.01
110 0.02 173 0.09 12 2.48 5 0.63 15 2.25 29 -23.48 6 10.9
111 3.37 174 0.09 13 2.46 6 2.51 16 2.48 30 -25.43 7 1.75
112 0.01 175 0.03 14 3.48 7 3.4 17 2.48 31 -18.34 8 0.008
113 3.38 176 0.09 IC502 8 3.41 18 0 32 -27.27 9 1.75
114 0.01 IC 501 Mpeg (ES8390) 1 3.39 IC504 19 4.98 33 -27.27
115 3.36 2 0.6 1 0.01 20 0 34 -25.71
PIN NO. EE Mode (V) Playback Mode (V)
116 0.01 3 3.39 2 0.01 21 2.47 35 -25.69
117 0.63 1 VD33 3.45 3.36 4 0.71 3 0.01 22 2.48 36 -25.69
118 0.56 2 VS33 0 0 5 0.71 4 0.01 23 2.47 37 -25.7
119 1.97 14 VD33 3.38 3.36 6 0 5 0.19 24 2.48 38 -25.7
120 1.65 15 VS33 0 0 7 0.91 6 3.47 25 4.06 39 -25.7
121 1.95 29VS33 0 0 8 0.71 7 0 26 2.47 40 -25.7
122 1.7 30 VD33 3.37 3.36 9 3.38 8 3.48 27 2.48 41 -25.7
123 0.08 36 VD33 3.37 3.36 10 0.86 IC401 (IP9010) 28 1.52 42 -25.7
124 1.29 37 VS33 0.02 0 11 0.94 29 1.52 43 -25.71
PIN NO. EE Mode (V) Playback M
125 3.4 38 VDD 1.53 1.51 12 0 30 4.96 44 -25.74
126 3.41 51 VS33 0.01 0 13 0.92 1 0.12 2.12 31 0 45 -25.73
127 2.14 52 VD33 3.38 3.36 14 3.38 2 0.11 2.16 32 0 46 -25.71
128 1.54 66 VD33 3.38 3.36 15 0.02 3 0.1 2.05 33 0 47 -25.7
129 0.59 67 VS33 0.01 0 16 0 4 0.09 2.18 34 0 48 -25.74
130 3.29 68 VDD 1.53 1.51 17 3.3 5 4.97 4.9 35 0 49 -27.44
131 0.09 72 RESET 4.29 4.31 18 3.2 6 1.7 1.72 36 3.42 50 -27.52
132 0.5 74 VS33 0.01 0 19 3.26 7 1.71 1.71 37 0.01 51 4.98
133 3.37 75 VD33 3.37 3.36 20 0.09 GND 0 0 38 0.01 52 0.014
134 0.02 81 VD33DAC 3.4 3.4 21 0.03 8 0.02 3.29 39 0.01 IC 3A1 (touch pad)
135 1.7 82 VS33DAC 0 0 22 0.09 9 1.09 1.08 40 0.01 1 0.1
136 1.7 87 VD33PLL 3.4 3.25 23 0.09 10 0 0 41 1.62 2 0.312
137 1.88 88 VS33PLL 0.01 0 24 0.55 11 0 0 42 1.65 3 0.311
138 1.88 89 AVD33 3.4 3.4 25 0.56 12 4.97 4.89 43 1.71 4 0.312
139 1.88 95 AVS33 0 0 26 1.6 13 0.09 0.21 44 1.65 5 0.314
140 1.88 99 VD33 3.37 3.36 27 3.38 14 0.09 0.21 45 0.01 6 0.311
141 1.84 100 VS33 0.01 0 28 0.01 15 0.04 3.39 46 3.42 7 0.073
142 1.84 104 VDD 1.53 1.51 29 1.38 16 0.36 0.826 47 4.96 8 4.67
143 2.13 107 VS33 0.01 0 30 1.53 17 0.11 2.08 48 0.04 9 4.59
144 2.14 108 VD33 3.37 3.36 31 1.79 18 0.11 2.18 IC 304 (PT6324) 10 0.305
145 1.65 115 VPB 3.37 3.35 32 1.38 19 4.97 4.9 1 4.65 11 0.337
146 0.02 116 VGD 0.01 0 33 2.62 20 1.7 1.72 2 3.8 12 0.307
147 1.71 122 V1650 1.95 1.7 34 0 21 1.7 1.41 3 3.7 13 0.308
148 1.71 127 VBD0 2.14 2.15 35 0.02 GND 0 0 4 1.4 14 0.31
149 1.71 133 VPA 3.37 3.35 36 0.02 22 0 0 5 0.059 15 0.033
150 1.73 134 VGA 0.02 0 37 3.38 23 1.7 1.7 6 0.06 16 0.034
151 1.35 153 AVD33 0 0 38 1.45 24 0.08 0.16 7 2.82 17 0.028
152 3.37 154 AVS33 0 0 39 0.02 25 0 0 8 0.14 18 0.04
153 0 155 DVCC 1.53 1.51 40 0 26 1.28 1.23 9 4.99 19 0.04
154 0 156 VD33 3.38 3.36 41 0.01 27 2.21 2.21 10 -19.65 20 0.041
155 1.53 157 VS33 0 0 42 0.83 28 1.56 1.56 11 -25.24 21 0.04
156 3.35 158 VDD 1.54 1.51 43 3.38 IC201 12 -27.09 22 0.041
157 0 163 VD33 3.38 3.36 44 0.89 13 -27.11 23 0.041
PIN NO. EE Mode (V)
158 1.5 164 VS33 0 0 45 0.77 14 -25.32 24 0.04
159 1.23 46 0.01 1 4.99 15 -27.09 25 0.04
PIN NO. EE Mode (V)
160 1.23 47 0.76 2 4.99 16 -27.09 26 0.039
161 1.38 IC508 48 0.68 3 3.42 17 -27.09 27 0.039
162 1.53 1 3.22 49 3.39 4 3.41 18 -21.75 28 5.03
163 3.47 2 3.22 50 0.87 5 4.95 19 -25.3 29 0.312

LGE Internal Use Only 3-65 3-66 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
 PRINTED CIRCUIT BOARD DIAGRAMS
1. MAIN P.C. BOARD DIAGRAM ( TOP VIEW )

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-67 3-68 LGE Internal Use Only
Only for training and service purposes
MAIN P.C. BOARD DIAGRAM ( BOTTOM VIEW )

LGE Internal Use Only 3-69 3-70 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
2. SMPS P.C. BOARD DIAGRAM

NOTE: Warning
Parts that are shaded are critical With
respect to risk of fire or electrical shock.

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-71 3-72 LGE Internal Use Only
Only for training and service purposes
3. SCART P.C. BOARD DIAGRAM ( TOP VIEW ) 4. TOUCH KEY P.C. BOARD DIAGRAM ( TOP VIEW )

SCART P.C. BOARD DIAGRAM ( BOTTOM VIEW ) TOUCH KEY P.C. BOARD DIAGRAM ( BOTTOM VIEW )

LGE Internal Use Only 3-73 3-74 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
5. FRONT P.C. BOARD DIAGRAM

6. MIC P.C. BOARD DIAGRAM

Copyright © 2008 LG Electronics. Inc. All right reserved. 3-75 3-76 LGE Internal Use Only
Only for training and service purposes
LGE Internal Use Only 3-78 3-79 Copyright © 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes