LIFTING PADEYE

Model data

In plane load inclination α 0deg

Padeye Force Fpadeye 4805.8kN

Design Factors DNV - RULES FOR MARINE OPERATIONS

It was considered in
sacs
γc - Used for lift points* γc 1.0 analysis
*is meant to account for severe consequences of single element failure.

Material Data

Fy 35.5 kNcm2

Weld Material Data:

Fwm 48.3 kN

cm2

Padeye Dimensions :

Padeye
radius
Rpadeye 320mm
Cheek radius
 Rcheek1 270mm
Padeye
thickness
tpadeye 44.5mm

Cheek thickness
tcheek 44.5mm

Diameter of Hole dhole 186mm

Weld tw 10mm

Base Area Abase 578.50cm2

Geometric Properties of the Section of Padeyes

Area Area 578.50cm2

Resistance modulus (Bending in Plane) Win 12530cm3

Resistance modulus (Bending out Plane) Wout 429cm3

Distance between center of hole and base of padeye

c 340mm

Factor n

n is the factor that allow perform the fillet weld execution

n 1.0

between the Cheek and the Padeye, and can vary

between 1.0 and 1.5.

Shackle

Shackle

Pin
diameter
dpin 180mm
Pin lenght W 250mm

Dimension g 630mm

Fcable = Fpadeye 5

Fcable Fpadeye 5
Fcable 2.45 103 tonnef

Wire rope Class 6x36 1 1/2

Wire rope diameter Ï•wire 225mm

Sling Force

Fpin Fpadeye γc

SECTION UTILIZED
Fpin 4805.8 kN

Loads

Fx1 Fpin cos(α)

Fx1 4.8 103 kN

Fy1 0.05 Fpin

Fy1 240.3 kN

Fz1 0.05 Fpin

Fz1 240.3 kN

Cheek Radius - Verification

dcheek 2 Rpadeye n tcheek

R dcheek
cheek2
2

Rcheek2 275.5 mm

Rcheek Rcheek1 if Rcheek1 Rcheek2

Rcheek2 otherwise

Rcheek 270 mm
Total thickness - Verification

Fpin
Ttotal Ttotal 83.6 mm
0.9Fy dpin

T 4 tcheek tpadeye T 222.5 mm

Tcheck "OK" if T Ttotal

"NOT OK" otherwise

Tcheck "OK"
Gap in the diameter of hole - Verification

fhole (1mm) if dpin 33mm

otherwise

0.03 dpin if 0.03 dpin 6mm

6mm otherwise

fhole 5.4 mm

dholecheck "OK" if dpin fhole dhole

"NOT OK" otherwise

dholecheck "OK"

Gap in the shackles - Verification

- First Verification

fshackles W Tfshackles 27.5 mm fmax 10025 W

fmax 62.5 mm

fshacklesallowable "NOT OK" if fshackles fmax

"OK" otherwise

fshacklesallowable "OK"

-Second Verification

d
pin
finstallation "OK" if g Rpadeye 2 Ï•wire6mm
"NOT OK" otherwise

d
pin

gap g Rpadeye 2 Ï•wiregap 175 mm

finstallation "OK"

Hole radius r dhole

hole 2

Pull out critical section

γ1 0deg

γ2 0deg
Design dimensions

Effective width of padeye plate:

b1 min 4 T 0.8 dhole Rpadeye rhole b1148.8 mm

Effective width of cheek

b2 min b1 Rcheek rhole b2148.8 mm

Effective width of padeye plate

b3 min 2 Rpadeye 2 b1 dhole Rcheek 2 b3 640mm

PADEYE VERIFICATIONS
Bearing stress check:

Fpin

fbe dpin tpadeye 2tcheek fbe 200 MPa

Fbe 0.9 Fy Fbe 319.5 MPa

fbe
UCbearing UCbearing 0.63
Fbe
Shear stress check:

Fpin
fv 2 R r t R r2 t fv 92.939 MPa

padeye hole padeye cheek hole cheek

Fv 0.4 Fy Fv 142 MPa

fv
UCShear UCShear 0.655
Fv

Net area tension:

Fpin
fNet.Area fNet.Area 121 MPa
2b1 tpadeye 4 b2 tcheek
FNet.Area 0.45 Fy FNet.Area 159.8 MPa

fNet.Area
UCNet.Area FNet.Area UCNet.Area 0.76

Yielding gross cross section:

Fpin
fGross.Section fGross.Section 168.7 MPa
b3 tpadeye

FGross.Section 0.6 Fy FGross.Section 213 MPa

fGross.Section
UCGross.Section UCGross.Section 0.792
FGross.Section

Pull out of the padeye and cheek:

F "OK" if 2 R R γ γt 0.6 F F

pinchek padeye cheek 1 2 padeye y pin
"NOT OK" otherwise

Fpinchek "OK"

Cheek weld:

aweldmin 3mm if tpadeye 6.4mm

5mm if 6.4mm tpadeye 12.7mm

6mm if 12.7mm tpadeye 19mm

8mm if tpadeye 19mm

aweldmin 8 mm
aweld "NOT OK" if tw aweldmin
" OK" otherwise

aweld " OK"

Cheek force

tcheek
Fcheek Fpin
tpadeye 2 tcheek

Fcheek 1601.9 kN

Cheek weld throat:

Fcheek

fw 2 π Rcheek 0.5 tw 0.707 fw 267.1 MPa

Fw min 0.30 Fwm 0.4 Fy 2 Fw 144.9 MPa

fw
UCweld Fw UCweld 1.843
Padeye Base Verification in accordance with AISC:

Stress due Axial Force:

 Fx1
fa Area fa 83.1 MPa

Stress due bending in plane:

Fz1 c
fin fin 6.5 MPa
Win
Stress due bending out of plane:

Ï•wire dhole

Fy1 c g2 2
fout fout 532.4 MPa
Wout
Area 0.058 m2

Fx1 4.806 106 N

Combined Stress

fa fin fout UCCombined0.6 Fy 0.6 Fy 0.75 Fy

UCCombined 2.42

Shear at Padeye:
fv.padeye 2
Fz1

3 Abase

fv.padeye 6.2 MPaFv.padeye 0.4 Fy Fv.padeye 142 MPa

fv.padeyeUCShear.Padeye Fv.padeye
UCShear.Padeye 0.044
SUMMARY

Cheek Radius - Verification:

Total thickness - Verification:

Gap in the diameter of hole - Verification:

Gap in the shackles - Verification:

 Rcheek 270 mm Rcheek1 270 mm

Tcheck "OK"

dholecheck "OK"
-First Verification:

-Second Verification:

Pull out of the padeye and cheek:

Cheek weld mininum:

Bearing stress check:

Shear stress check:

Net area tension:

Yielding gross cross section:

Cheek weld throat:

Verification Combined:

Shear at Padeye:
fshacklesallowable "OK"

finstallation "OK"

Fpinchek "OK"

aweld " OK"

UCbearing 0.63

UCShear 0.65

UCNet.Area 0.76

UCGross.Section 0.792
UCweld 1.843

UCCombined 2.42

UCShear.Padeye 0.044

MPa 1 106Pa