Scribd
Upload
1K views1 page

Timing Belt Guide Fiesta 14 Diesel

This document provides instructions for replacing the timing belt on 1.4 liter diesel engines in certain Citroen, Ford, and Peugeot models. The key steps are: 1) install alignment and locking tools, 2) position the new tensioner and tighten its screw, 3) install the belt in the specified order, 4) adjust the tensioner and tighten its screw, 5) remove the alignment and locking tools. It also notes that Dayco is the OE supplier and provides replacement kits with extended warranties.

Uploaded by

cesar leon
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
1K views1 page

Timing Belt Guide Fiesta 14 Diesel

This document provides instructions for replacing the timing belt on 1.4 liter diesel engines in certain Citroen, Ford, and Peugeot models. The key steps are: 1) install alignment and locking tools, 2) position the new tensioner and tighten its screw, 3) install the belt in the specified order, 4) adjust the tensioner and tighten its screw, 5) remove the alignment and locking tools. It also notes that Dayco is the OE supplier and provides replacement kits with extended warranties.

Uploaded by

cesar leon
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Tech Tips

Timing belt guide


JOBS

>>
Fiesta 1.4 diesel
Belt replacement on the 1.4 litre diesel engine can sometimes be problematic, so
Dayco has issued a technical bulletin to guide technicians through the process and
avoid some common problems.
• Re-assemble the other component in the A
Makes/Models: >>
These instructions are for the following
reverse order to disassembly.

• Insert the tool to secure the flywheel and


Citroen (C1, C2, C3, Nemo, Xsara)
Ford (Fiesta, Fusion)

B
Peugeot(107, 206, 207, 307, 1007) tighten the driving shaft pulley screw to a torque
with the following Engine Codes: of 30 Nm + 180°.
DV4TD, DV4TD/L4, DV4TD/L5, DV4TED, F6JA ,
F6JC The Dayco replacement kit includes the timing
belt, tensioner and idler and carries the reference
Installation Procedure number KTB310. The kit contains a timing belt
• Once the engine has been cleaned and made with 144 teeth, 25.4 mm wide (94923, OES
ready for the installation of the new belt, make 9464034380), a tensioner (ATB2236, OES
96413140) and an idler (ATB2090, OES
sure the driving shaft aligning tool (C) and the

C
96415393. )A water pump kit is also available
camshaft locking tool (A) are properly fitted.
(KTBWP3100), which contains all of these items
• Make sure the fuel pump pinion (B) is properly plus an OE quality water pump.
aligned.

• Position the new tensioner correctly,


The Fiesta 1.2, 1.4 and 1.6 litre petrol engines are
notable because although it is the auxiliary belt
introducing the plate in the pin located on the that drives the water pump, the timing belt
base and tighten the bearing fastening screw. tensioner is located on the water pump bracket

• Fit the timing belt in the following order:


and requires careful adjustment, in order to set
the correct tension of the belt when a
driving shaft pinion, idler, camshaft pinion, replacement is installed. However, the installation
water pump pinion, fuel pump pinion and then itself is a simple and straightforward process.
tensioner.

• Slacken the tensioner fastening screw and


Dayco is the original equipment (OE) timing belt
supplier for the Ford Fiesta and has been so for
remove the locking pin. several years. From October 2010 the OE belt on

• With an allen wrench, rotate the tensioner


vehicles fitted with 1.6-litre petrol engine was
upgraded from a standard to a High Tenacity (HT)
pulley anti-clockwise, until the indicator is or ‘white’ belt.
positioned in the centre, as in Fig. 1. Fig. 1 A properly positioned indicator on the

• Tighten the tensioner screw to a torque of 30


Replacement kits for the petrol engines contain tensioner pulley
both the tensioner and belt, with reference
Nm. numbers KTB461 for the standard belt and

• Remove the camshaft locking tool (A) and the


KTB764 for the HT belt for the 1.6-litre engine.

driving shaft aligning tool (C).


Dayco’s unique Long Life + 1 year warranty is free
• Make sure the fuel pump pinion is properly of charge to the factor, workshop and motorist,
aligned. but extends the warranty on the Dayco HT belt

• Rotate the driving shaft by 10 turns clockwise.


from the existing two years, to a market leading
three-year term.

• Make sure the indicator is still aligned as in Full technical information is available through the
Fig.1. Dayco website, www.dayco.com, or contact P R

• Make sure the above-mentioned aligning and


Reilly on 01-832-0006.
Tensioner with locking pin in position in the
locking tools (both A and C) can be easily re- indicator. The round hole in the centre of the
inserted. If not, repeat the installation tensioner is for the fastening screw and the
procedure. hex shaped hole is for an allen key.

AUTOBIZ TECH TIPS February 2014 Compendium >> originally published in Autobiz Jul 2013

You might also like