Scribd
Upload
117 views6 pages

Engineering Lab Report Analysis

This report summarizes an experiment on a water cooling tower system. Tables of data collected at cooling loads of 0.5kW, 1.0kW, and 1.5kW show the temperatures at various points in the system. Graphs show that higher heater power results in increased water temperatures and larger cooling ranges. The conclusion is that increasing the cooling load leads to an increase in the cooling tower's temperature rise and cooling range, achieving the aim of investigating this relationship.

Uploaded by

Muhamad Syazwan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
117 views6 pages

Engineering Lab Report Analysis

This report summarizes an experiment on a water cooling tower system. Tables of data collected at cooling loads of 0.5kW, 1.0kW, and 1.5kW show the temperatures at various points in the system. Graphs show that higher heater power results in increased water temperatures and larger cooling ranges. The conclusion is that increasing the cooling load leads to an increase in the cooling tower's temperature rise and cooling range, achieving the aim of investigating this relationship.

Uploaded by

Muhamad Syazwan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 6

UNIVERSITI

UNIVERSITITEKNIKAL MALAYSIA
TEKNIKAL MELAKA
MALAYSIA MELAKA
FACULTY OF MECHANICAL ENGINEERING
FACULTY OF MECHANICAL
MECHANICAL ENGINEERING
ENGINEERING LABORATORY III
MECHANICAL ENGINEERING LABORATORY III
BMCG 3011
BMCG 2011
INFORMAL REPORT
BIL: NAME: MATRIX NO:
1. MUHAMAD SYAZWAN BIN ABDUL KADIR B041510140 CLASS SESSION:
2. MUHAMMAD AFIQUDDIN BIN NASAHROM B041510141
3/7
3. MUHAMAD ALIF BIN AZMI B041510174
4. MUHAMMAD FAIZ IZWAN BIN MOHD YUSOF B041510157
5. MUHAMMAD HANAFI BIN AHMAD FAIZAL B041510213
LAB GROUP:
B2

REPORT SUBMISSION
DATE:29/4/2019

SEMESTER/SESSION: SEM 2 / SESSION 2018-2019


EXPERIMENT TITLE:
WATER COOLING TOWER SYSTEM

LECTURER: PN. NOR IZYAN BINTI ZULKAFLI/DR NIDZAMMUDIN BIN MD. YUSOF

LECTURER REMARKS EVALUATION


Objectives
Introduction & Theory
Procedure and Apparatus
Data and Result
Analysis and Discussion
Conclusions
References

TOTAL
1.0 OBJECTIVE

To investigate the relationship between cooling load and cooling range.

2.0 DATA AND RESULTS

Table 1: Data for 0.5kW Cooling Load

No. T1 T2 T3 T4 T5 T6 T7 Heater Flowrate Orifice Pressure


(°C) (°C) (°C) (°C) (°C) (°C) (°C) Power (LPM) Differential Drop
(W) (Pa) (Pa)
1 23.9 23.5 23.2 22.2 26.8 23.6 23.6 538 3 0.0 0.0
2 24.0 23.5 22.9 22.2 26.0 22.8 23.5 540 3 0.0 0.0
3 24.1 23.6 22.7 22.2 25.4 22.7 23.5 539 3 0.0 0.0
4 23.9 23.5 22.5 22.2 25.2 22.5 23.4 537 3 0.0 0.0
5 22.1 23.6 22.5 22.2 24.9 22.1 23.4 536 3 0.0 0.0

Table 2: Data for 1.0kW Cooling Load

No. T1 T2 T3 T4 T5 T6 T7 Heater Flowrate Orifice Pressure


(°C) (°C) (°C) (°C) (°C) (°C) (°C) Power (LPM) Differential Drop
(W) (Pa) (Pa)
1 22.8 22.5 25.8 22.2 26.3 22.6 23.4 1023 3 0.0 0.0
2 22.6 22.5 25.4 22.2 27.2 23.1 23.3 1029 3 0.0 0.0
3 22.7 22.6 25.8 22.1 27.8 23.5 23.4 1028 3 0.0 0.0
4 22.6 22.4 25.2 22.2 28.4 23.7 23.5 1024 3 0.0 0.0
5 22.4 22.2 25.5 22.1 28.6 23.9 23.4 1025 3 0.0 0.0
Table 3: Data for 1.5kW Cooling Load

No. T1 T2 T3 T4 T5 T6 T7 Heater Flowrate Orifice Pressure


(°C) (°C) (°C) (°C) (°C) (°C) (°C) Power (LPM) Differential Drop
(W) (Pa) (Pa)
1 23.9 23.7 24.3 22.3 30.7 24.8 23.4 1538 3 0.0 0.0
2 23.6 23.8 25.0 22.1 32.1 25.6 23.4 1532 3 0.0 0.0
3 23.8 23.8 25.5 22.1 32.6 25.9 23.4 1550 3 0.0 0.0
4 23.6 23.7 25.5 22.1 32.9 26.0 23.6 1556 3 0.0 0.0
5 23.5 23.7 25.5 22.3 33.2 26.4 23.4 1541 3 0.0 0.0

Figure 1 shows water inlet and outlet temperature for 0.5kW


3.0 ANALYSIS AND DISCUSSION

Figure
2 shows
water
inlet and outlet temperature for 1.0kW

Figure 3 shows
water inlet
and outlet
temperature for 1.5kW
Figure 4 shows graph of relationship for three different power
CONCLUSION

For the conclusion, the experiment can be concluded that if the power of the heater is increasing
the temperature increase and the cooling range of the tower will also increase. The aim of the
experiment is to achieve the successful investigation of the relationship between cooling load
and cooling range. We have discovered many different things while conducting this experiment.
Other than that, importance things that we just noticed on the experiment is always make sure the
system is running at the steady state before start collecting the date during the experiment
running.

You might also like