LEXMARK MS/MX SERIES ®

TONER & DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS

LEXMARK MS/MX TONER & DRUM UNIT

www.uninetimaging.com
© 2014 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
 LEXMARK MS/MX SERIES TONER & DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS

REMANUFACTURING THE LEXMARK

MS/MX SERIES TONER & DRUM CARTRIDGES
By Mike Josiah and the Technical Staff at UniNet

First introduced in October 2012, the Lexmark MS/MX series is based on a new 35-70 ppm (depending on the model)
Lexmark 1200 dpi engine. These engines for the first time in their larger printers use a two-cartridge system. The toner hopper is
basically a tube with a chip. The drum unit contains the drum, waste chamber, developer roller, PCR, wiper blade, and doctor blade.
The basic design is similar to the T650 all-in-one cartridge, but is broken into two cartridges.

Due to the speed, fuser characteristics and transfer efficiency, the toner is completely different and unique to this series.
When choosing a toner for these machines make sure the transfer efficiency is high so the waste does not overflow. If your
replacement toner runs at more than 2.5g of waste per 1,000 pages, you run the risk of overflowing the drum unit waste hopper.
The smaller drum unit can hold up to 160g of waste toner and the larger drum unit can hold up to 220g. OEM and UniNet
X Generation® toners run at less than 1.5g per 1,000 pages.

Lexmark calls their new toner system “Unison." This toner has a lower melting point (thus saving energy on fusing temperatures),
a high-transfer efficiency, and a “shake-free” design for the toner cartridge.

www.uninetimaging.com
© 2014 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
 LEXMARK MS/MX SERIES TONER & DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS

There are quite a few machines based on these engines and also quite a few cartridges. Lexmark made this cartridge as complicated
as they could. Basically there are physically two different toner cartridges and two different drum units. The MS/MX 310, 410,
510 and 610 series all use the smaller toner cartridge and drum unit. The MS/MX 710, 711, 810, 812 series all use the larger
toner cartridge and drum units.

www.uninetimaging.com
© 2014 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
 LEXMARK MS/MX SERIES TONER & DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS

The toner cartridges feed the toner to the drum units through a small toner port.

The drum units are either rated for 60,000 pages (small version) or 100,000 pages (large version).

With drum units selling new for as low as $45.00USD, there is not much demand for remanufacturing them. That being said,
if you’re selling MICR toner cartridges, you must also supply MICR drum units. Both types of drum units come pre-charged with
toner so you need to know how to take a new drum unit and clean it out. When rebuilding them it’s important to put in 50-60g of
toner so they are pre-charged properly. Because of that we have included the instructions for both cartridges here. The toner
cartridges as stated above are basically a tube with a chip. They are very easy to remanufacture, and have very high
profit margins.

MACHINES CURRENTLY AVAILABLE BASED ON THE LEXMARK MS/MX ENGINE

MS310 Series: MS310d, 310dn (35 ppm)
MS410 Series: MS410d, 410dn (40 ppm)
MS510 Series: MS510d, 510dn (45 ppm)
MS610 Series: MS610dn, 610de, 610dte, 610dtn (50 ppm)
MS710 Series: MS710d, 710dn (50 ppm)
MS711 Series: MS711d, 711dn (55 ppm)
MS810 Series: MS810d, 810de, 810dtn, 810dtv (55 ppm)
MS811 Series: MS811n, 811dn, 811dtn (63 ppm)
MS812 Series: MS812de, 812dn, 812dtn (70 ppm)

MX310 Series: MX310d, 310dn (35 ppm)

MX410 Series: MX410de (40 ppm)
MX510 Series: MX510dhe, 510dthe (45 ppm)
MX610 Series: MX610de (50 ppm)
MX611 Series: MX611de, 611dhe, 611dte (50 ppm)
MX710 Series: MX710de (63 ppm)
MX711 Series: MX711de, 711dhe, 711dthe (70 ppm)
MX810 Series: MX810de, 810dfe, 810dme, 810dte, 810dtfe, 810dtme, 810dxe, 810dxfe, 810dxme (55 ppm)
MX811 Series: MX811de, 811dfe, 811dme, 811dte, 811dtfe, 811dtme, 811dxe, 811dxfe, 811dxme (63 ppm)
MX812 Series: MX812de, 812dfe, 812dme, 812dte, 812dtfe, 812dtme, 812dxe, 812dxfe, 812dxme (70 ppm)

www.uninetimaging.com
© 2014 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
 LEXMARK MS/MX SERIES TONER & DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS

The following Lexmark machines (1145 & 3150) were released in 10/2012 but there is little to no information on the Lexmark
website for them. They use the MS/MX style cartridges, but the chips will be different...

LEXMARK 1145 & 3150

M1145/XM1145 (45 ppm)
M3150/XM3150 (50 ppm)

DELL VERSIONS
B2360 Series: B2360d, 2360dn
B3460 Series: B3460dn
B3465 Series: B3465dnf
B5460 Series: B5460dn
B5465 series: B5465dnf

SOURCE TECHNOLOGIES VERSIONS (MICR)

ST9712
ST9720
ST9722
ST9730

As with all Lexmark cartridges, the "Return Program" cartridges have killer-type chips installed that will not allow the cartridge to
be used again until the chipboard is replaced. The standard cartridges will work without replacing the chips. Replacement chips
are available for the toner cartridges. If drum unit chips are ever developed, it remains to be seen.

Lexmark has also released cartridges for different areas of the world. The Americas are one region; Europe, the Middle East and
Africa are another (EMEA); Latin America, and the Asia Pacific region is the last. As in the past, the only difference in the cartridges
besides the part numbers is the chips.

In the smaller series, a "starter" or low yield cartridge can be made into a high yield (20K) if the machine accepts that yield.
The same goes for the larger toner cartridges. They can be made into a 45K cartridge but the machine must accept that yield.

www.uninetimaging.com
© 2014 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
 LEXMARK MS/MX SERIES TONER & DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS

There are quite a few different cartridges, all with different chips. They are all included below in the least confusing way.
The Americas Lexmark part numbers for these cartridges are as follows...

SMALL MS SERIES CARTRIDGES

“Return Program” 1.5K* toner cartridge: (501) 50F1000 List $64.99** MS 310/410/510/610
“Return Program” 5K* toner cartridge: (501H) 50F1H00 List $149.99** MS 310/410/510/610
“Return Program” 10K* toner cartridge: 501X) 50F1X00 List $225.99** MS 410/510/610
“Return Program” 20K* toner cartridge: 501U) 50F1U00 List $330.99** MS 510/610
“Return Program” 60K* drum cartridge: (500Z) 50F0Z00A List $44.99** All 300/400/500/600 MS/MX machines

Standard 5K* cartridge: (500HA) 50F0HA0 List $195.99** MS 310/410/510/610

Standard 10K* cartridge: (500XA) 50F0XA0 List $271.99** MS 410/510/610
Standard 20K* cartridge: (500UA) 50F0UA0 List $377.99** MS 510/610
Standard 60K* drum cartridge: (500ZA) 50F0ZA0 List $70.99** All 300/400/500/600 MS/MX machines

LARGE MS SERIES CARTRIDGES

“Return Program” 6K* toner cartridge: (521) 52D1000 List $141.99** MS 710/711/810/811/812
“Return Program” 25K* toner cartridge: (521H) 52D1H00 List $419.99** MS 810/811/812
“Return Program” 45K* toner cartridge: (521X) 52D1X00 List $519.99** MS 410/510/610
“Return Program” 100K* drum cartridge: (520Z) 50F0Z00A List $47.99** All 710/711/810/811/812 MS/MX machines

Standard 25K* cartridge: (520HA) 52D0HA0 List $496.99** MS 810/811/812

Standard 45K* cartridge: (520UA) 52D0XA0 List $596.99** MS 811/812
Standard 100K* drum cartridge: (520ZA) 52D0ZA0 List $73.99** All 710/711/810/811/812 MS/MX machines

SMALL MX SERIES CARTRIDGES

“Return Program” 2.5K* toner cartridge: (601) 60F1000 List $89.99** MX310/410/510/511/610/611
“Return Program” 10K* toner cartridge: (601H) 60F1H00 List $149.99** MX310/410/510/511/610/611
“Return Program” 20K* toner cartridge: (601X) 60F1X00 List $330.99** MX510/511/610/611
“Return Program” 60K* drum cartridge: (500Z) 50F0Z00A List $44.99** All 300/400/500/600 MS/MX machines

Standard 10K* cartridge: (600HA) 60F0HA0 List $294.99** MX310/410

Standard 20K* cartridge: (600XA) 60F0XA0 List $399.99** MX510/511/610/611
Standard 60K* drum cartridge: (500ZA) 50F0ZA0 List $70.99** All 300/400/500/600 MS/MX machines

LARGE MX SERIES CARTRIDGES

“Return Program” 6K* toner cartridge: (621) 62D1000 List $141.99** MX710/711/810/811/812
“Return Program” 25K* toner cartridge: (621H) 62D1H00 List $331.99** MX710/711/810/811/812
“Return Program” 45K* toner cartridge: (621X) 62D1X00 List $519.99** MX711/810/811/812
“Return Program” 100K* drum cartridge: (520Z) 50F0Z00A List $47.99** All 710/711/810/811/812 MS/MX machines

Standard 25K* cartridge: (620HA) 62D0HA0 List $409.99** MX710

Standard 45K* cartridge: (620XA) 62D0XA0 List $596.99** MX711/810/811/812
Standard 100K* drum cartridge: (520ZA) 52D0ZA0 List $73.99** All 710/711/810/811/812 MS/MX machines

M1145/XM1145 toner: 24B6035; 16K List $184.63

M3150/XM3150 toner: 24B6186; 16K List $190.95
M1145/M3150 drum unit: 24B6040; 60K List $94.95

*Yield based on ISO/IEC 19752. **List prices (in U.S. American Dollars) current as of March 2014.

www.uninetimaging.com
© 2014 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
 LEXMARK MS/MX SERIES TONER & DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS

As you can see there are quite a few cartridges out there for these machines. Thankfully though as stated above there are only two
physically different toner cartridges (small and large) and two physically different drum units (small and large). What you need to
know is which machine your cartridge is going to be used in, and the required yield. By knowing that, you can choose the correct
chip and toner load.

REQUIRED TOOLS
1. Toner approved vacuum
2. Small screwdriver (common style)
3. Phillips head screwdriver (#1)
4. Needle-nose pliers

REQUIRED SUPPLIES
1. Replacement Toner for Lexmark MS (use correct load for your chip)
2. Replacement Toner cartridge chip
3. Drum padding powder
4. Cotton Swabs
5. Isopropyl Alcohol
6. Cotton Pads

NOTE: For the purposes of these instructions we have used the small versions of the toner and drum cartridges. The larger versions
are slightly different physically, but the same steps apply.

www.uninetimaging.com
© 2014 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
 LEXMARK MS/MX SERIES TONER & DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS

TONER CARTRIDGE INSTRUCTIONS

1. Remove the three screws on the right (gear) side end cap.

Remove the end cap.

www.uninetimaging.com
© 2014 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
 LEXMARK MS/MX SERIES TONER & DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS

2. Remove the fill plug and clean out all remaining toner from
the hopper. Be careful not to disturb the toner port mechanism.

3. For the large toner cartridge only: remove the three screws and end cap on the opposite side.

www.uninetimaging.com
© 2014 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
 LEXMARK MS/MX SERIES TONER & DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS

4. Remove the two small screws on the inside of the end cap. 5. Remove chip holder and chip.

6. Replace the chip in the chip holder. 7. Install the chip holder and two screws.

www.uninetimaging.com
© 2014 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
 LEXMARK MS/MX SERIES TONER & DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS

8. On the large cartridge: install the chip, end cap, and three 9. Fill the hopper with the appropriate toner load to match the
screws. chip you installed. Replace the fill plug.

10. Install the end cap and three screws.

www.uninetimaging.com
© 2014 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
 LEXMARK MS/MX SERIES TONER & DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS

OPC (DRUM) CARTRIDGE INSTRUCTIONS

1. Remove the two screws from both sides of the handle.

www.uninetimaging.com
© 2014 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
 LEXMARK MS/MX SERIES TONER & DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS

2. Pull the edge of the frame out slightly and remove 3. Remove the developer assembly.
the handle.

4. With a small Phillips jeweler’s screwdriver, remove the drum 5. Remove the axle pin.
axle pin screw.

www.uninetimaging.com
© 2014 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
 LEXMARK MS/MX SERIES TONER & DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS

6. With a small pair of needle nose pliers, turn the locking ring until loose.

Pry the drive gear and ring from the drum axle shaft.

7. Remove the drum.

www.uninetimaging.com
© 2014 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
 LEXMARK MS/MX SERIES TONER & DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS

8. Remove the PCR and both PCR holders.

9. Remove the two screws and the wiper blade. 10. Clean the wiper blade sealing foam. Make sure the foam is
not damaged during cleaning and that it is positioned in its
Clean out any toner from the waste chamber. proper location when done.

www.uninetimaging.com
© 2014 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
 LEXMARK MS/MX SERIES TONER & DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS

11. Pad the new wiper blade with your preferred

wiper blade lubricant. Replace the blade and two screws into
the cartridge.

12. Clean the PCR.

Install the two PCR holders, and then install the PCR.

www.uninetimaging.com
© 2014 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
 LEXMARK MS/MX SERIES TONER & DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS

13. Install the cleaned drum.

Place the spring on the drum axle so that it fits into the slot.

14. Press the locking ring onto the drum shaft and turn to lock. 15. Install the drum drive gear.

www.uninetimaging.com
© 2014 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
 LEXMARK MS/MX SERIES TONER & DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS

16. Install the drum axle pin and screw.

17. On the developer unit, grasp the keyed shaft of the developer roller with a pair of needle nose pliers.

Turn the opposite-side white gear, so that it unlocks. Remove the gear.

www.uninetimaging.com
© 2014 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
 LEXMARK MS/MX SERIES TONER & DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS

18. Turn up the lock on the gear side of the developer roller. 19. Remove the developer roller.

20. Using a size T-10 Torx screwdriver, remove the four screws from the doctor blade.

www.uninetimaging.com
© 2014 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
 LEXMARK MS/MX SERIES TONER & DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS

21. Remove the doctor blade.

Clean out the toner from the supply chamber and feed roller.

Be careful not to damage the feed roller or the two doctor blade contacts!

22. Press the fill plug out from the inside. Make sure all NOTE: Once clean, you can see how the toner is transported
remaining toner has been removed from the chamber. from the small feed hole through the entire developer unit.
There is an auger system and mixing paddles that move
the toner. If you want to see them work, hold the chamber so
that the gears are on the left side. Turn the large white gear
towards you.

www.uninetimaging.com
© 2014 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
 LEXMARK MS/MX SERIES TONER & DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS

23. Install the doctor blade and the four Torx screws. Make sure the contact on the right side (non-gear) is on top of the doctor
blade, is screwed in place, and is making contact with the doctor blade.

24. Clean the developer roller with a dedicated developer roller 25. Press on the large white gear, using pliers on the opposite
cleaner. (If used) install the developer roller, keyed end towards side of the developer roller. Turn the gear until locked.
the gear side of the chamber. Turn the locking arm until it locks.

www.uninetimaging.com
© 2014 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
 LEXMARK MS/MX SERIES TONER & DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS

26. Fill the hopper with 50g of new replacement toner and re-
place the fill plug. If you are converting the drum unit to MICR,
make sure you use the same MICR toner you are using for the
toner cartridge!

27. Hold the waste chamber walls out slightly and drop in the developer assembly.

Make sure the gears and bushings all fit in their slots properly.

www.uninetimaging.com
© 2014 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
 LEXMARK MS/MX SERIES TONER & DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS

28. Snap in the left side of the handle and then the right side.

Make sure the tabs lock!

29. Install the screws on each side of the handle.

www.uninetimaging.com
© 2014 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
 LEXMARK MS/MX SERIES TONER & DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS

CARTRIDGE TROUBLESHOOTING
MS810 Cartridge Repetitive Defect Chart:
OPC drum: 96.8 mm
Developer roller: 47.8 mm
PCR: 28.5 mm
Upper fuser roller: 95.2 mm
Lower fuser roller: 94.25 mm

MS310 Cartridge Repetitive Defect Chart:

OPC drum: 97 mm
Developer roller: 47 mm
PCR: 38 mm
Upper fuser roller: 80 mm
Lower fuser roller: 80 mm

Machine Error Codes:

Most of the error messages appear to be in text, and do not need an explanation. No numeric messages are listed in the user
guide except for the following...

42.xy = Cartridge region mismatch

The X = the printer region, and the Y = the cartridge region. Both must match each other.

Region Codes (see text at beginning of article):

0 = Global
1 = USA, Canada
2 = European economic Area (EEA) Switzerland region
3 = Asia Pacific, Australia, New Zealand region
4 = Latin America
5 = Africa, Middle East, rest of Europe
9 = Invalid region

TAKING TEST PRINTS

Printer Menu:
1. Press the “MENU” key
2. Press the DOWN ARROW until “REPORTS” Shows on the display
3. Press the “Select” button”
4. Press the DOWN ARROW until the check mark is next to the page you wish to print
5. Press the “Select” button”
6. These pages include:
A. Menu Settings page
B. Device statistics
C. Network Setup page
D. Profiles List
E. Print Fonts
F. Print Directory
G. Asset report

www.uninetimaging.com
© 2014 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]