Scribd
Upload
254 views

Alcohol Level Tester

This document describes an alcohol level tester circuit that uses an MQ3 alcohol sensor and LEDs to indicate various levels of alcohol consumption. The circuit is inexpensive and easy to use. It works by detecting changes in the alcohol sensor's resistance when exposed to alcohol vapors, which causes more LEDs to illuminate on an IC and show higher alcohol levels. The circuit can be assembled on a small PCB and tested using an open alcohol bottle without actual consumption.

Uploaded by

Asad Waseem
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
254 views

Alcohol Level Tester

This document describes an alcohol level tester circuit that uses an MQ3 alcohol sensor and LEDs to indicate various levels of alcohol consumption. The circuit is inexpensive and easy to use. It works by detecting changes in the alcohol sensor's resistance when exposed to alcohol vapors, which causes more LEDs to illuminate on an IC and show higher alcohol levels. The circuit can be assembled on a small PCB and tested using an open alcohol bottle without actual consumption.

Uploaded by

Asad Waseem
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Alcohol Level Tester

Yogesh Shukla

A lot of accidents happen every day due to drunk driving. This is a very useful circuit for
testing whether a driver is drunk or not. The circuit is easy to use, inexpensive and indicates
various levels of alcohol consumption through LEDs.

Circuit and working


Fig. 1 shows circuit of the alcohol level tester. Alcohol sensor MQ3 is used here to detect the
alcohol fumes’ concentration.

Fig. 1: The alcohol level tester’s circuit diagram


Fig. 2: An actual-size, single-
Fig. 3: Component layout for the
side PCB layout for the circuit
PCB
Download:http://www.electronicsforu.com/electronicsforu/circuitarchives/my_documents/m
y_files/Alcohol_Level_Tester.zip

Pins 2 and 5 of MQ3 are connected to 5V power supply and the ground, respectively, as
shown in the circuit. These pins are actually the heating-coil pins of the sensor. The input
pins 1 and 3 of the sensor are also connected
to 5V. Pins 4 and 6 are connected to input pin
5 of LM3914 (IC1).

The number of glowing LEDs indicates the


concentration level of alcohol detected by the
sensor. Resistor R1 and preset VR1 are used
to calibrate the output voltage from the
sensor.

When a drunk breathes out near sensor1, the


alcohol vapours come in contact with MQ3
sensor and its resistance changes. This raises
signal level at pin 5 of IC1 a larger number of
LEDs start glowing than the two that were
glowing before.

Construction and testing


An actual-size, single-side PCB for the alcohol level tester is shown in Fig. 2 and its
component layout in Fig. 3. After assembling the circuit on PCB, enclose it in a suitable
case.
Switch on the circuit and verify the test points
mentioned in the table. Before using the circuit,
vary VR1 until LED1 and LED2 glow when the
sensor is in normal environment. Now open the
cork of an alcohol bottle and bring it near
sensor1. You will notice that LED3, LED4 and
LED5 also start glowing. As you bring the alcohol
bottle’s open mouth very close to sensor1, all the
LEDs (LED1 through LED10) will start glowing.

We do not recommend that you actually consume some alcohol to test the circuit. The
above test with a bottle of alcohol, or its sample in a small glass, should suffice for most
purposes. Until you find a drunk, of course!

The author is an electronics hobbyist

http://electronicsforu.com/electronicsforu/circuitarchives/view_article.asp?
sno=1850&article_type=1&id=1126&tt=unhot&b_type=new

You might also like