CDX-G3100UE/G3100UV/

G3150UP/G3150UV
SERVICE MANUAL AEP Model
UK Model
Ver. 1.1 2014.11 CDX-G3100UV

E Model
CDX-G3150UV

Australian Model
CDX-G3150UP

Russian Model
CDX-G3100UE

Photo: CDX-G3150UV

The service manual of the mechanism deck, used in

this model, has been issued in a separate volume.
Please refer to the service manual of the MG-101
series for the mechanism deck information.

• The tuner and CD sections have no adjustments. CDX-G3000UE/G3000UV/

Model Name Using Similar Mechanism
G3050UP/G3050UV/G3070UV
Mechanism Type MG-101CF-188
Optical Pick-up Name DAX-25A

SPECIFICATIONS
Tuner section MW/LW AM SW
(AEP and UK models) Tuning range: Tuning range: Tuning range:
MW: 531 – 1,602 kHz 531 – 1,602 kHz (at 9 kHz step) SW1: 2,940 – 7,735 kHz
FM SW2: 9,500 – 18,135 kHz
LW: 153 – 279 kHz 530 – 1,710 kHz (at 10 kHz step)
Tuning range: (except for 10,140 – 11,575 kHz)
AM tuning step:
87.5 – 108.0 MHz Antenna (aerial) terminal: Antenna (aerial) terminal:
9 kHz/10 kHz switchable
Antenna (aerial) terminal: External antenna (aerial) connector External antenna (aerial) connector
Antenna (aerial) terminal:
External antenna (aerial) connector Sensitivity: MW: 26 μV, LW: 50 μV Intermediate frequency:
External antenna (aerial) connector
Intermediate frequency: -2,463.8 to -1,710.1 kHz and
Sensitivity: 26 μV
FM CCIR: -1,956.5 to -487.3 kHz and (E, Mexican, Indian and Australina models) +1,710.0 to +2,418.4 kHz
+500.0 to +2,095.4 kHz Sensitivity: 26 μV
Usable sensitivity: 7 dBf FM (Saudi Arabia model)
Selectivity: 75 dB at 400 kHz Tuning range: FM
87.5 – 108.0 MHz (at 50 kHz step) Tuning range: 87.5 – 108.0 MHz CD Player section
Signal-to-noise ratio: 73 dB
87.5 – 108.0 MHz (at 100 kHz step) Antenna (aerial) terminal: Signal-to-noise ratio: 95 dB
Separation: 50 dB at 1 kHz
87.5 – 107.9 MHz (at 200 kHz step) External antenna (aerial) connector Frequency response: 10 – 20,000 Hz
Frequency response: 20 – 15,000 Hz
FM tuning step: Intermediate frequency: Wow and flutter: Below measurable limit
MW/LW 50 kHz/100 kHz/200 kHz switchable FM CCIR: -1,956.5 to -487.3 kHz and The maximum number of: (CD-R/CD-RW only)
Tuning range: Antenna (aerial) terminal: +500.0 to +2,095.4 kHz folders (albums): 150 (including root folder)
MW: 531 – 1,602 kHz External antenna (aerial) connector Usable sensitivity: 7 dBf files (tracks) and folders: 300 (may less than 300
LW: 153 – 279 kHz Intermediate frequency: if folder/file names contain many characters)
Selectivity: 75 dB at 400 kHz
Antenna (aerial) terminal: FM CCIR: -1,956.5 to -487.3 kHz and displayable characters for a folder/file name: 32
Signal-to-noise ratio: 73 dB
External antenna (aerial) connector +500.0 to +2,095.4 kHz (Joliet)/64 (Romeo)
Separation: 50 dB at 1 kHz
Sensitivity: MW: 26 μV, LW: 50 μV Usable sensitivity: 7 dBf Corresponding codec: MP3 (.mp3) and WMA (.wma)
Frequency response: 20 – 15,000 Hz
Selectivity: 75 dB at 400 kHz
(Russian model) MW
Signal-to-noise ratio: 73 dB
FM Separation: 50 dB at 1 kHz
Tuning range: 531 – 1,602 kHz – Continued on next page –
Tuning range: Antenna (aerial) terminal:
Frequency response: 20 – 15,000 Hz
FM1/FM2: 87.5 – 108.0 MHz External antenna (aerial) connector
(at 50 kHz step) Sensitivity: 26 μV
FM3: 65 – 74 MHz (at 30kHz step)
Antenna (aerial) terminal: E, Mexican, Indian and Australian models
FM/AM COMPACT DISC PLAYER
External antenna (aerial) connector
Intermediate frequency:
FM CCIR: -1,956.5 to -487.3 kHz and
+500.0 to +2,095.4 kHz
FM OIRT: -1,815.6 to -943.7 kHz and
+996.6 to +1,776.6 kHz AEP, Russian and UK models
FM/MW/LW COMPACT DISC PLAYER
Usable sensitivity: 7 dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio: 73 dB
Separation: 50 dB at 1 kHz
Frequency response: 20 – 15,000 Hz
Saudi Arabia model
FM/MW/SW COMPACT DISC PLAYER
9-896-049-02
2014K33-1 Sony Corporation
© 2014.11 Published by Sony Techno Create Corporation
CDX-G3100UE/G3100UV/G3150UP/G3150UV
Ver. 1.1

USB Player section

Interface: USB (Full-speed)
Copyrights
Maximum current: 1 A
The maximum number of recognizable tracks: Windows Media is either a registered trademark or
folders (albums): 256 trademark of Microsoft Corporation in the United
files (tracks) per folder: 256 States and/or other countries.
Corresponding codec:
MP3 (.mp3) and WMA (.wma)
This product is protected by certain intellectual
Power amplifier section property rights of Microsoft Corporation. Use or
Output: Speaker outputs distribution of such technology outside of this
Speaker impedance: 4 – 8 ohms product is prohibited without a license from
Maximum power output: 55 W × 4 (at 4 ohms) Microsoft or an authorized Microsoft subsidiary.
General iPhone, iPod, iPod classic, iPod nano, and iPod
Outputs:
Audio outputs terminal (rear, sub)
touch are trademarks of Apple Inc., registered in
Power antenna (aerial)/Power amplifier control the U.S. and other countries.
terminal (REM OUT)
Inputs: MPEG Layer-3 audio coding technology and patents
Remote controller input terminal licensed from Fraunhofer IIS and Thomson.
Antenna (aerial) input terminal
AUX input jack (stereo mini jack)
USB port
Pandora, the Pandora logo, and the Pandora trade
Power requirements: 12 V DC car battery (negative dress are trademarks or registered trademarks of
ground (earth)) Pandora Media, Inc., used with permission.
Dimensions:
Approx. 178 mm × 50 mm × 177 mm Android is a trademark of Google Inc.
(7 1/ 8 in × 2 in × 7 in) (w/h/d)
Mounting dimensions:
Approx. 182 mm × 53 mm × 160 mm
(7 1/ 4 in × 2 1/ 8 in × 6 5/ 16 in) (w/h/d)
Mass: Approx. 1.2 kg (2 lb 11 oz)
Package contents:
Remote commander (1): RM-X211
(CDX-G3150UV only)
Parts for installation and connections (1 set)
Design and specifications are subject to change
without notice.

NOTES ON CHIP COMPONENT REPLACEMENT

• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.

FLEXIBLE CIRCUIT BOARD REPAIRING

• Keep the temperature of soldering iron around 270 °C during
repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.

Saudi Arabia model:

This product is classified as a Class 1 Laser product
under IEC 60825-1:2007.

This label is located on bottom surface of the

product.

CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radia-
tion exposure.

SAFETY-RELATED COMPONENT WARNING!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE

WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

2
 CDX-G3100UE/G3100UV/G3150UP/G3150UV
SECTION 1
SERVICING NOTES
TABLE OF CONTENTS The SERVICING NOTES contains important information for
servicing. Be sure to read this section before repairing the
1. SERVICING NOTES ............................................. 3 unit.

2. GENERAL .................................................................. 6
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
3. DISASSEMBLY
3-1. Disassembly Flow ........................................................... 12 The laser diode in the optical pick-up block may suffer electro-
3-2. Mini Fuse (Blade Type) (FU1), Cover ............................ 12 static break-down because of the potential difference generated by
3-3. Sub Panel Assy................................................................ 13 the charged electrostatic load, etc. on clothing and the human body.
3-4. CD Mechanism Deck (MG-101CF-188) ........................ 13 During repair, pay attention to electrostatic break-down and also
3-5. MAIN Board ................................................................... 14 use the procedure in the printed matter which is included in the
3-6. Service Position .............................................................. 15 repair parts.
The flexible board is easily damaged and should be handled with
4. DIAGRAMS care.
4-1. Block Diagram - MAIN Section -................................... 16
4-2. Block Diagram NOTES ON LASER DIODE EMISSION CHECK
- PANEL/POWER SUPPLY Section - ............................ 17 Never look into the laser diode emission from right above when
4-3. Printed Wiring Boards - MAIN Section (1/2) - .............. 18 checking it for adjustment. It is feared that you will lose your sight.
4-4. Printed Wiring Boards - MAIN Section (2/2) - .............. 19
4-5. Schematic Diagram - MAIN Section (1/3) - ................... 20 If the optical pick-up block is defective, please replace the whole
4-6. Schematic Diagram - MAIN Section (2/3) - ................... 21 optical pick-up block.
4-7. Schematic Diagram - MAIN Section (3/3) - ................... 22 Never turn the semi-fixed resistor located at the side of optical
pick-up block.
5. EXPLODED VIEWS
optical pick-up
5-1. Sub Panel Section ........................................................... 30
5-2. Chassis Section ............................................................... 31

6. ELECTRICAL PARTS LIST .............................. 32

Accessories are given in the last of the electrical parts list.

semi-fixed resistor

UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)

: LEAD FREE MARK

Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
3
CDX-G3100UE/G3100UV/G3150UP/G3150UV
Ver. 1.1

REPLACING THE LITHIUM BATTERY OF THE REMOTE 3. Input the alphanumeric character of 12 digits of “F XXXXXX”
COMMANDER (CDX-G3150UV only) displayed on the liquid crystal display, and execute the destina-
Under normal conditions, the battery will last tion setting.
approximately 1 year. (The service life may be Note: Refer to following “1-3. Entering the Destination Code” for opera-
shorter, depending on the conditions of use.) tion method.
When the battery becomes weak, the range of the 4. The resetting operation is executed by pressing the [ OFF
remote commander becomes shorter.
SRC] button for 1 second after the setting ends, and the unit
CAUTION returns to the normal condition.
Danger of explosion if battery is incorrectly
replaced. Replaced only with the same or
1-2. Display in Destination Setting Mode
equivalent type.
(Displayed characters/values in the following figure are example)
+ side up
Destination code
SHUF

Notes on the lithium battery

ˎ Keep the lithium battery out of the reach of children.
OP5 OP4 OP3 OP2 OP1 OP0
Should the battery be swallowed, immediately
consult a doctor. 12 digit
ˎ Wipe the battery with a dry cloth to ensure a good
contact.
ˎ Be sure to observe the correct polarity when installing 1-3. Entering the Destination Code
the battery. • Method of operation by main unit
ˎ Do not hold the battery with metallic tweezers,
otherwise a short-circuit may occur.

WARNING
Battery may explode if mistreated. Do not
recharge, disassemble, or dispose of in fire.

DESTINATION ABBREVIATIONS
The following abbreviations for model destinations are used in this
service manual.

• Abbreviations 1. Rotate the control dial, and select the alphanumeric character
AUS : Australian model of “0 to F”.
EA : Saudi Arabia model 2. The digit advances by pressing the [PUSH ENTER/MENU] or
IND : Indian model [> M SEEK+] button.
MX : Mexican model The digit returns by pressing the [MODE ] or [SEEK– m
RU : Russian model
.] button.
3. The setting is completed by pressing the [PUSH ENTER/
NOTE OF REPLACING THE COMPLETE MAIN BOARD
MENU] button, and the initialization operation is done.
OR SYSTEM CONTROLLER (IC501)
When the complete MAIN board or system controller (IC501) is
• Method of operation by remote commander
replaced, the destination setting is necessary.
(CDX-G3150UV only)
Note: The model to which the remote commander is not attached can
1. Destination Setting also be operated by using the remote commander.
Set destination according to the procedure below.

1-1. Setting the Destination Code

1. In the state of source off (the clock is displayed on the liquid
crystal display), enter the test mode by pressing the buttons in
order of the [SHUF 4] t [5] t [PAUSE 6] (press only the
[PAUSE 6] button for two seconds).
2. In the state in which the system controller version is displayed
on the liquid crystal display (refer to following figure), enter
the destination setting mode by pressing the buttons in order
of the [> M SEEK+] t [SEEK– m .] t [PUSH EN-
TER/MENU] or pressing the buttons on the remote command-
er in order of the [b] t [B] t [ENTER].
(Displayed characters/values in the following figure are ex-
ample) 1. Press the [V] or [v] button, and select the alphanumeric char-
System controller version acter of “0 to F”.
2. The digit advances by pressing the [b] button.
SHUF
The digit returns by pressing the [B] button.
3. The setting is completed by pressing the [ENTER] button, and
the initialization operation is done.

– Continued on next page –

4
 CDX-G3100UE/G3100UV/G3150UP/G3150UV
Ver. 1.1

1-4. Destination Code TEST DISCS

Model Destination OP5 OP4 OP3 OP2 OP1 OP0 Use following TEST DISC (for CD) when this unit confirms the
CDX-G3100UE Russian 8 8 1 0 3 7 operation and checks it.
CDX-G3100UV AEP, UK 0 8 1 0 2 1
Part No. Description
CDX-G3150UP Australian 0 A 1 8 5 0
3-702-101-01 DISC (YEDS-18), TEST
E, Mexican 3 8 1 8 4 0 4-225-203-01 DISC (PATD-012), TEST
CDX-G3150UV Saudi Arabia 2 8 1 8 4 4
Indian 1 8 1 8 4 0 NOTE OF PERFORMING THE OPERATION CHECK
When performing the operation check in the state that is removed
the CD mechanism deck from the main unit, it is necessary to use
2. Confirmation After Destination Setting
a long flexible flat cable.
Execute the following operation after completing the destination
When performing the operation check, use following flexible flat
setting, and confirm a correct destination was set.
cable.
Destination setting checking method:
Part No. Description
1. In the state of source off (the clock is displayed on the liquid
1-846-819-31 CABLE FLEXIBLE FLAT (27 CORE)
crystal display), enter the test mode by pressing the buttons in
(Length: 150 mm)
order of the [SHUF 4] t [5] t [PAUSE 6] (press only the
[PAUSE 6] button for two seconds).
NOTE OF REPLACING THE KEY BOARD
2. In the state in which the system controller version is displayed
When the KEY board is defective, replace the FRONT PANEL
on the liquid crystal display (refer to following figure), enter
OVERALL ASSY (Ref. No. FP1).
the destination setting value display mode by pressing the [
SCRL DSPL] button twice.
NOTE OF REPLACING THE IC1301 ON THE MAIN BOARD
(Displayed characters/values in the following figure are ex-
IC1301 on the MAIN board cannot replace with single. When this
ample)
part is damaged, replace the complete mounted board.
System controller version
SHUF CLEANING THE CONNECTORS
The unit may not function properly if the
connectors between the unit and the front panel
are not clean. In order to prevent this, detach the
front panel and
(page 5) and
clean theclean the connectors
connectors with with
3. Confirm the alphanumeric character of 12 digits in liquid crys- a cotton swab. Do not apply too much force.
Otherwise, the connectors may be damaged.
tal display is an value correctly input.
(Displayed characters/values in the following figure are ex-
ample)
Destination code
SHUF

Notes
ˎ For safety, turn off the ignition before cleaning the
connectors, and remove the key from the ignition
switch.
OP5 OP4 OP3 OP2 OP1 OP0 ˎ Never touch the connectors directly with your fingers
or with any metal device.
12 digit

4. The resetting operation is executed by pressing the [ OFF

SRC] button for 1 second after the confirming ends, and the
unit returns to the normal condition.

5
CDX-G3100UE/G3100UV/G3150UP/G3150UV
SECTION 2
This section is extracted
GENERAL from instruction manual.

(CDX-G3100UE)

Подключение
Установка/подключение
Сабвуфер*1
*3
Внимание!
ˎ Подведите все заземляющие провода к *3
общей точке заземления.
ˎ Не допускайте попадания проводов под винты Усилитель мощности*1
или между подвижными деталями (например,
между направляющими сидений).
ˎ Во избежание короткого замыкания перед
установкой соединений выключите зажигание
автомобиля.
ˎ Сначала подсоедините провод питания ʘ к
устройству и громкоговорителям, а затем — к ʘ
контактам внешнего источника питания. *2
ˎ В целях безопасности обязательно изолируйте
все свободные неподсоединенные провода Подробнее см.
электроизоляционной лентой. “Установка соединений”
(стр. 19).

Меры предосторожности Подробнее см. “Схема подключения питания”

(стр. 19).
ˎ Тщательно выбирайте место для установки
от проводного пульта
аппарата, чтобы он не мешал управлению
дистанционного управления (не
автомобилем. входит в комплект поставки)*4
ˎ Не устанавливайте аппарат там, где он будет
подвержен воздействию пыли, грязи, от автомобильной антенны*5
чрезмерной вибрации или высоких
температур, например в местах, куда
попадают прямые солнечные лучи, или вблизи
вентиляционных решеток обогревателей.
*1 Не входит в комплект поставки.
ˎ В целях обеспечения надежной и безопасной
*2 Полное сопротивление громкоговорителей:
установки используйте лишь входящие в
4–8 Ом × 4.
комплект монтажные детали.
*3 Кабель с разъемами RCA (не входит в комплект
Примечание относительно провода питания поставки).
(желтый) *4 В зависимости от типа автомобиля используйте
При подключении данного устройства вместе с адаптер для проводного пульта дистанционного
другими cтepeокомпонeнтaми номинальное управления (не входит в комплект поставки).
значение силы тока в контуре питания автомобиля *5 В зависимости от типа автомобиля используйте
должно превышать суммарное значение силы тока, адаптер (не входит в комлект поставки), если
указанное на предохранителях всех компонентов. разъем антенны не подходит.

Регулировка угла установки

Отрегулируйте угол установки так, чтобы он
составлял менее 45°.

ɟ К разъему электропитания автомобиля

Подсоединение для поддержки
Установка соединений
памяти
Если используется антенна с электроприводом Когда к устройству подсоединен желтый провод
без релейного блока, подсоединение этого питания, блок памяти будет постоянно получать
устройства с помощью прилагаемого провода питание, даже при выключенном зажигании.
питания ʘ может привести к повреждению
антенны. Подключение громкоговорителей
Источник
ɞ К разъему громкоговорителя автомобиля 12 бесперебойного Желтый ˎ Перед подключением громкоговорителей
электропитания выключите устройство.
ˎ Во избежание повреждений используйте
Антенна с
громкоговорители с полным сопротивлением
электроприводом/
Синий/с белыми 4–8 Ом и соответствующей предельно
13 управление
полосками допустимой мощностью.
усилителем мощности
(REM OUT)
1 È Фиолетовый Импульсный источник
15 Красный
Задний электропитания
громкоговоритель Фиолетовый/с
2 ¾ черными 16 Заземление Черный
(правый)
полосками
3 È Серый Простое подключение сабвуфера
Передний
громкоговоритель Серый/с Сабвуфер можно использовать без усилителя
4 (правый) ¾ черными мощности, если подключить его к кабелю
полосками заднего громкоговорителя.
5 È Белый
Передний
Белый/с Передний
громкоговоритель
6 (левый) ¾ черными громкоговоритель
полосками
7 È Зеленый
Задний
громкоговоритель Зеленый/с
8 ¾ черными Сабвуфер
(левый)
полосками
Примечания
ˎ Требуется подготовка кабелей задних
громкоговорителей.
ˎ Во избежание повреждений используйте
сабвуфер с полным сопротивлением 4–8 Ом и
соответствующей предельно допустимой
мощностью.

6
 CDX-G3100UE/G3100UV/G3150UP/G3150UV

Схема подключения питания Установка устройства в приборной

Установка панели
Проверьте разъем подключения
вспомогательного питания автомобиля и Перед установкой убедитесь, что фиксаторы с
правильно распределите соединения проводов Отсоединение защитной манжеты и обеих сторон кронштейна ʓ согнуты вовнутрь
(в зависимости от типа автомобиля). на 2 мм.
кронштейна
Разъем подключения вспомогательного питания
1 Установите кронштейн ʓ в
Перед монтажом устройства отсоедините
приборную панель, затем выгните
защитную манжету ͨ и кронштейн ʓ от
устройства. выступы наружу, чтобы обеспечить
плотную фиксацию.
1 Захватите оба края защитной
манжеты ͨ, а затем вытащите ее. 182 мм

53 мм
Общая схема подключения
Красный Красный ͨ

Желтый Желтый Фиксатор

ʓ
Источник
12 бесперебойного Желтый 2 Вставьте оба ключа для демонтажа ͧ 2 Прикрепите устройство к кронштейну
электропитания до щелчка, потяните кронштейн ʓ ʓ, затем вставьте защитную манжету
15
Импульсный источник
Красный
вниз, а затем потяните устройство ͨ.
электропитания вверх, чтобы отсоединить его.
ͧ
Если красный и желтый провода
переставлены местами ʓ

Красный Красный

ʓ
†
ͨ

Желтый Желтый ͩ
Направьте крючок внутрь.

Импульсный источник
12 Желтый ͪ
электропитания
Источник
15 бесперебойного Красный Примечания
электропитания ˎ Если фиксаторы не согнуты или выгнуты наружу,
устройство не будет установлено надлежащим
Если в автомобиле нет положения ACC образом и может выпасть.
ˎ Убедитесь, что 4 фиксатора на защитной манжете
Красный Красный ͨ надлежащим образом вставлены в отверстия,
имеющиеся в устройстве.

Замена предохранителя
Желтый Желтый
При замене предохранителей Предохранитель
обязательно используйте только (10 A)
После проверки соответствия соединений и те, которые соответствуют силе
проводов импульсного источника тока, указанной на
электропитания подключите устройство к оригинальном предохранителе.
автомобильному контуру электропитания. В Если перегорел
случае возникновения каких-либо вопросов или предохранитель, проверьте
проблем, связанных с подключением подключение питания и
устройства, которые не рассматриваются в замените предохранитель. Если после замены
настоящем руководстве, обратитесь за советом предохранитель снова перегорел, это может
к дилеру автомобильной фирмы. означать неисправность устройства. В этом
случае обратитесь к ближайшему дилеру Sony.

7
CDX-G3100UE/G3100UV/G3150UP/G3150UV

(CDX-G3100UV)

Connection
Connection/Installation
Subwoofer*1
*3
Cautions
ˎ Run all ground (earth) leads to a common *3
ground (earth) point.
ˎ Do not get the leads trapped under a screw, or Power amplifier*1
caught in moving parts (e.g., seat railing).
ˎ Before making connections, turn the car ignition
off to avoid short circuits.
ˎ Connect the power supply lead ʘ to the unit and
speakers before connecting it to the auxiliary
power connector.
ˎ Be sure to insulate any loose unconnected leads ʘ
*2
with electrical tape for safety.

For details, see “Making

Precautions connections” (page 17).

ˎ Choose the installation location carefully so that

the unit will not interfere with normal driving See “Power connection diagram” (page 17)
operations. for details.
ˎ Avoid installing the unit in areas subject to dust,
dirt, excessive vibration, or high temperature, from a wired remote control
such as in direct sunlight or near heater ducts. (not supplied)*4
ˎ Use only the supplied mounting hardware for a
safe and secure installation. from a car antenna (aerial)*5

Note on the power supply lead (yellow)

When connecting this unit in combination with other
stereo components, the amperage rating of the car
circuit to which the unit is connected must be higher *1 Not supplied
than the sum of each component’s fuse amperage *2 Speaker impedance: 4 – 8 Ω × 4
rating. *3 RCA pin cord (not supplied)
*4 Depending on the type of car, use an adaptor for a
Mounting angle adjustment wired remote control (not supplied).
Adjust the mounting angle to less than 45°. *5 Depending on the type of car, use an adaptor (not
supplied) if the antenna connector does not fit.

Making connections Subwoofer Easy Connection

You can use a subwoofer without a power amplifier
If you have a power antenna (aerial) without a relay when it is connected to a rear speaker cord.
box, connecting this unit with the supplied power
supply lead ʘ may damage the antenna (aerial). Front speaker
ɞ To the car’s speaker connector

Subwoofer

Notes
ˎ Preparation of the rear speaker cords is required.
1 È Purple ˎ Use a subwoofer with an impedance of 4 to 8 ohms,
Rear speaker and with adequate power handling capacities to
Purple/black
2 (right) ¾ avoid damage.
striped
3 Front speaker È Gray Memory hold connection
4 (right) ¾ Gray/black striped When the yellow power supply lead is connected,
5 È White power will always be supplied to the memory circuit
Front speaker even when the ignition switch is turned off.
White/black
6 (left) ¾
striped
7 È Green
Speaker connection
Rear speaker ˎ Before connecting the speakers, turn the unit off.
Green/black
8 (left) ¾ ˎ Use speakers with an impedance of 4 to 8 ohms,
striped
and with adequate power handling capacities to
ɟ To the car’s power connector avoid damage.

continuous power
12 Yellow
supply
power antenna (aerial) /
13 power amplifier control Blue/white striped
(REM OUT)
15 switched power supply Red
16 ground (earth) Black

8
 CDX-G3100UE/G3100UV/G3150UP/G3150UV

Power connection diagram Installation Mounting the unit in the dashboard

Make sure your car’s auxiliary power connector, and Before installing, make sure the catches on both
match the connections of cords correctly sides of the bracket ʓ are bent inwards 2 mm (3/32
depending on the car. Removing the protection collar and the in).
bracket
Auxiliary power connector
1 Position the bracket ʓ inside the
Before installing the unit, remove the protection dashboard, then bend the claws outward
collar ͨ and the bracket ʓ from the unit. for a tight fit.
1 Pinch both edges of the protection collar 182 mm (7 1/4 in)
ͨ, then pull it out.
53 mm (2 1/8 in)

Common connection ͨ
Red Red

Catch
ʓ
Yellow Yellow
2 Mount the unit onto the bracket ʓ, then
continuous power 2 Insert both release keys ͧ until they
12 Yellow attach the protection collar ͨ.
supply click, and pull down the bracket ʓ, then
15 switched power supply Red pull up the unit to separate.
ͧ ʓ
When the positions of the red and yellow
leads are inverted
Red Red

ͨ
ʓ
†
ͩ
Yellow Yellow Face the hook inwards.
ͪ
12 switched power supply Yellow
continuous power
15 Red
supply Notes
ˎ If the catches are straight or bent outwards, the unit
When the car without ACC position will not be installed securely and may spring out.
ˎ Make sure the 4 catches on the protection collar ͨ
Red Red are properly engaged in the slots of the unit.

Fuse replacement
When replacing the fuse, be sure Fuse (10 A)
Yellow Yellow to use one matching the
amperage rating stated on the
2 Mount the unit onto the bracket ʓ, then original fuse. If the fuse blows,
attach the protection collar ͨ. check the power connection and
replace the fuse. If the fuse blows
again after replacement, there
may be an internal malfunction. In such a case,
consult your nearest Sony dealer.

9
CDX-G3100UE/G3100UV/G3150UP/G3150UV
Ver. 1.1

(CDX-G3150UP/G3150UV)

Connection
Connection/Installation
Subwoofer*1
*3
Cautions
ˎ Run all ground (earth) leads to a common *3
ground (earth) point.
ˎ Do not get the leads trapped under a screw, or Power amplifier*1
caught in moving parts (e.g., seat railing).
ˎ Before making connections, turn the car ignition
off to avoid short circuits.
ˎ Connect the yellow and red power supply leads
only after all other leads have been connected.
ˎ Be sure to insulate any loose unconnected leads
with electrical tape for safety. ͬ

White
Precautions White/black striped
Front speaker*1*2
ˎ Choose the installation location carefully so that Gray
the unit will not interfere with normal driving Gray/black striped
operations. Green
ˎ Avoid installing the unit in areas subject to dust,
dirt, excessive vibration, or high temperature, Green/black striped
Rear speaker*1*2
such as in direct sunlight or near heater ducts. Purple
ˎ Use only the supplied mounting hardware for a Purple/black striped
safe and secure installation.
Black
Note on the power supply lead (yellow)
Yellow
When connecting this unit in combination with other For details, see “Making
stereo components, the amperage rating of the car Red
connections” (page 18).
circuit to which the unit is connected must be higher Blue/white striped (MAX 0.4A)
than the sum of each component’s fuse amperage
rating.

Mounting angle adjustment from a wired remote control

Adjust the mounting angle to less than 45°. (not supplied)*4

from a car antenna (aerial)

*1 Not supplied
*2 Speaker impedance: 4 – 8 Ω × 4
*3 RCA pin cord (not supplied)
*4 Depending on the type of car, use an adaptor for a
wired remote control (not supplied).

Making connections Subwoofer Easy Connection

You can use a subwoofer without a power amplifier
ɞ To a common ground (earth) point when it is connected to a rear speaker cord.
First connect the black ground (earth) lead, then
connect the yellow and red power supply leads.
Front speaker
ɟ To the +12 V power terminal which is
energized at all times
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
Subwoofer
ɠ To the +12 V power terminal which is
energized when the ignition switch is set to
the accessory position Note
Use a subwoofer with an impedance of 4 to 8 ohms,
If there is no accessory position, connect to the and with adequate power handling capacities to avoid
+12 V power (battery) terminal which is damage.
energized at all times.
Be sure to first connect the black ground (earth) Memory hold connection
lead to a common ground (earth) point.
When the yellow power supply lead is connected,
ɡ To the power antenna (aerial) control lead or power will always be supplied to the memory circuit
the power supply lead of the antenna (aerial) even when the ignition switch is turned off.
booster
It is not necessary to connect this lead if there is Speaker connection
no power antenna (aerial) or antenna (aerial) ˎ Before connecting the speakers, turn the unit off.
booster, or with a manually-operated telescopic ˎ Use speakers with an impedance of 4 to 8 ohms,
antenna (aerial). and with adequate power handling capacities to
To AMP REMOTE IN of an optional power avoid damage.
amplifier
This connection is only for amplifiers and a
power antenna (aerial). Connecting any other
system may damage the unit.

10
 CDX-G3100UE/G3100UV/G3150UP/G3150UV

Mounting the unit in the dashboard Mounting the unit in a Japanese car
Installation You may not be able to install this unit in some
Before installing, make sure the catches on both makes of Japanese cars. In such a case, consult your
sides of the bracket ʓ are bent inwards 2 mm (3/32 Sony dealer.
Removing the protection collar and the in). When mounting in a Japanese car, see
bracket “Mounting the unit in a Japanese car” (page 19). TOYOTA
ͫ
Before installing the unit, remove the protection
1 Position the bracket ʓ inside the to dashboard/center console
collar ͨ and the bracket ʓ from the unit. dashboard, then bend the claws outward
for a tight fit.
1 Pinch both edges of the protection collar
ͨ, then pull it out. 182 mm (7 1/4 in)
Bracket
53 mm (2 1/8 in)
Bracket
ͨ

ͫ
Existing parts supplied with
your car

Catch
ʓ

2 Mount the unit onto the bracket ʓ, then NISSAN

2 Insert both release keys ͧ until they
click, and pull down the bracket ʓ, then attach the protection collar ͨ. ͫ
to dashboard/center console
pull up the unit to separate.
ͧ
ʓ

Bracket

ʓ ͨ Bracket
†

ͩ
ͫ
Face the hook inwards. Existing parts supplied with
your car
ͪ

Notes Note
ˎ If the catches are straight or bent outwards, the unit To prevent malfunction, install only with the supplied
will not be installed securely and may spring out. screws ͫ.
ˎ Make sure the 4 catches on the protection collar ͨ
are properly engaged in the slots of the unit.
Fuse replacement
When replacing the fuse, be sure Fuse (10 A)
to use one matching the
amperage rating stated on the
original fuse. If the fuse blows,
check the power connection and
replace the fuse. If the fuse blows
again after replacement, there
may be an internal malfunction. In such a case,
consult your nearest Sony dealer.

11
CDX-G3100UE/G3100UV/G3150UP/G3150UV
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.

3-1. DISASSEMBLY FLOW

SET

FRONT PANEL SECTION 3-6. SERVICE POSITION

Note: Illustration of disassembly is omitted. (Page 15)

3-2. MINI FUSE (BLADE TYPE) (FU1),

COVER
(Page 12)

3-3. SUB PANEL ASSY

(Page 13)

3-4. CD MECHANISM DECK (MG-101CF-188)

(Page 13)

3-5. MAIN BOARD

(Page 14)

Note: Follow the disassembly procedure in the numerical order given.

3-2. MINI FUSE (BLADE TYPE) (FU1), COVER

Note: When installing the cover, check

that four bosses are all locked.
4 cover
OK

2 two bosses

Boss is locked.

NG

3 three claws 2 two bosses

Boss is unlocked.

1 mini fuse (blade type)

(FU1)

12
 CDX-G3100UE/G3100UV/G3150UP/G3150UV

3-3. SUB PANEL ASSY

2 two claws
3 sub panel assy
Note: When installing the sub panel assy,
align two ribs and two holes.

rib

hole

hole 2 two claws

1 two screws
(PTT2.6 u 6)
rib

3-4. CD MECHANISM DECK (MG-101CF-188)

Note 1: The service manual of the mechanism deck, used in this model has
been issued in a separate volume. Please refer to the service manual
of the MG-101 series for the mechanism deck information.

Note 2: When installing the CD mechanism block,

‡+RZWRLQVWDOO align the rib and the slot.
WKH&'PHFKDQLVPGHFN 6 bracket (CD)

4 cable flexible flat (27 core)

(FFC1) (CN401)
1 cable flexible flat 7 CD mechanism deck 5 two screws
(27 core) (FFC1) (MG-101CF-188) (PTT2.6 u 4)
(CN401)

Note 2: When installing the

CD mechanism block,
2 cable flexible flat align the rib and
(27 core) (FFC1) the slot.
(CN704)

1 screw
(PTT2.6 u 6)
slot

2 Lift up the CD mechanism block

in the direction of the arrow.

3 slot

1 screw
(PTT2.6 u 6)
3 connector
(CN704)
Note 3: When installing the cable flexible flat (27 core) (FFC1), insert straight to the connector and lock a connector completely.
No slanting after insertion.

OK NG NG NG
Insert is straight to the interior. Connector is unlock. Insert is incline Insert is shallow
cable flexible flat cable flexible flat cable flexible flat cable flexible flat
(27 core) (FFC1) (27 core) (FFC1) (27 core) (FFC1) (27 core) (FFC1)

connector connector connector connector

13
CDX-G3100UE/G3100UV/G3150UP/G3150UV

3-5. MAIN BOARD

Note: When the complete MAIN board is replaced, the destination setting is necessary. Refer to “NOTE OF
REPLACING THE COMPLETE MAIN BOARD OR SYSTEM CONTROLLER (IC501)” on page 4.

2 two screws
1 two ground point screws (PTT2.6 u 8)
(PTT2.6 u 6)

(EA)
6 MAIN board

5 sheet heat transfer

3 claw

4 Remove the MAIN board block

in the direction of the arrow.

3 claw

3 claw
3 claw

(EA)

‡3DVWLQJSRVLWLRQRIWKHVKHHWKHDWWUDQVIHU

rear side
MAIN board guide line

guide line

sheet heat transfer

14
 CDX-G3100UE/G3100UV/G3150UP/G3150UV

3-6. SERVICE POSITION

Note 1: The service position below cannot be performed with the flexible
flat cable (length: 80 mm) used with the unit. Refer to “NOTE OF
PERFORMING THE OPERATION CHECK” in the servicing
notes, and use a long flexible flat cable (length: 150 mm).

OK OK

CD mechanism deck CD mechanism deck

insulating sheet insulating sheet

stand stand

cable flexible flat (27 core) cable flexible flat (27 core)
main unit main unit
(length: 150 mm) (length: 150 mm)
Note 2: Do not cable flexible flat (27 core) is Note 2: Do not cable flexible flat (27 core) is
damaged by the edge of the chassis. damaged by the edge of the chassis.

NG NG

CD mechanism deck CD mechanism deck

Note 3: CD mechanical deck should Note 3: CD mechanical deck should
not be placed vertically. not be placed vertically.

cable flexible flat (27 core) main unit cable flexible flat (27 core)
main unit
(length: 150 mm) (length: 150 mm)

NG

CD mechanism deck
Note 4: CD mechanical deck should
not be placed upside down.

cable flexible flat (27 core) main unit

(length: 150 mm)

CDX-G3100UE/G3100UV/G3150UP/G3150UV
15 15
 CDX-G3100UE/G3100UV/G3150UP/G3150UV
SECTION 4
DIAGRAMS
4-1. BLOCK DIAGRAM - MAIN Section -
CD MECHANISM CENTER VOLTAGE
DECK BLOCK FP_B+ GENERATOR
(MG-101CF-188) IC403

B 5 AIN RFOUT 2 1 EFMIN DATA 53 60 DATA DACOUT_L 4 3 LVRIN LFOUT 1

J401
BCK 52 59 BCK
A 7 BIN
LRCK 51 58 LRCK LROUT 2 L
C 6 CIN MCLK 50 61 MCLK REAR
LINE AMP
DO 47 29 CD_DO R-CH R
8 DIN IC401, 402
DI 46 27 CD_DI AUDIO OUT

F 13 EIN
CL 45 28 CD_CL R-CH +
CE 44 30 CD_CE SUB
E 14 FIN
SBCK 43 40 SBCK MUTING MUTING
PW 42 39 PW Q406 Q410
1/2VCC 11 VREF
RF AMP, SFSY 41 38 SFSY
DIGITAL SERVO PROCESSOR SBSY 40 37 SBSY
PD 20 LDS
IC701 OPCDM 39 48 OPCDM GAIN GAIN GAIN MUTING
AUTOMATIC BUSYB 49 57 CD_BUSYB CONTROL CONTROL CONTROL CONTROL R-CH
LD POWER CONTROL 19 LDD RESB 48 85 CD_RESB Q411 Q412 Q413 Q407 – 409
Q700
KEY BOARD (1/2)
FOCUS 21 FDO POWER AMP
TRACK 22 TDO AUX_L 13 L3_IN_P IC300 CN301 (1/2)
SL 23 SLDO USB CONTROLLER, INPUT SELECTOR, 6
SP 24 SPDO AUX_GND 14 L3_IN_N AUDIO DSP, ELECTRICAL VOLUME FL+ 5 FL+
IC601 12 IN_FL 8
XOUT

36 L_SW FL– 3 FL–

XIN

R-CH 5
61 62
AUX_R FR+
R-CH 7
FR–
X701
D+ 69 UDP1 2
16.934MHz
RL+ 9 RL+
D– 68 UDM1 11 IN_RL 4
RL– 7 RL–
1

AC_GND
RR+

MUTE
STBY
TU01 EEPROM R-CH 3
TUX-DSP04 (TUNER UNIT) IC602 RR–
16 22 4

J01 RF_ANT_IN AUDIO_OUT_L 9 L1_IN CP_SDA 83 2 SDA

(ANTENNA IN) CP_SCL 82 6 SCL
AUDIO_OUT_R R-CH

CMD_ERR

RESETB

X12OUT
R-ch is omitted due to same as L-ch.

USB_IN
BUSYB

SMONI
SIFDO

SIFCK
SIFCE

X12IN
RXD1
TXD1

SIFDI
SIGNAL PATH
SDA
SCL

45 46 54 53 52 55 56 86 62 47 51 75 74 : AUDIO
: TUNER
X601
12MHz
: CD
39 38 26 27 21 20 22 42 34 41 44 45 43 : AUX
LITHIO_DATA

BUSY

SYSRST
LITHIO_CLK

RX
TX
SDI
SDO
SCK
CE

CMD_ERR
USBIN
WDT_MON
DRV_ON 99 DRV_ON S-GAIN_A 59
: USB
LOAD 96 MEC_LOAD S-GAIN_B 60
EJECT 100 MEC_EJECT S-GAIN_C 61
SYSTEM CONTROLLER
L_SW 94 MEC_LSW ATT 56
IC501 (1/2)
D_SW 93 MEC_DSW BEEP 68
IN_SW 97 MEC_INSW AMP_MUTE 57
CF2

CF1

SELF 98 MEC_SELFSW AMPSTB 58

XT2

XT1

7 6 10 9

X501 X502
32.768kHz 9.25MHz

CDX-G3100UE/G3100UV/G3150UP/G3150UV
16 16
 CDX-G3100UE/G3100UV/G3150UP/G3150UV

4-2. BLOCK DIAGRAM - PANEL/POWER SUPPLY Section - THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
SYSTEM CONTROLLER (In addition to this, the necessary note is printed in each block.)
IC501 (2/2)
D503 REGULATOR For Printed Wiring Boards. For Schematic Diagrams.
J801 81 RC_IN1 RESET 5 IC201 CN301 (2/2) Note: Note:
(REMOTE IN) 80 RC_IN0 D200 15 • X : Parts extracted from the component side. • All capacitors are in μF unless otherwise noted. (p: pF) 50
62 KEY_ACK0 P-COM_3.3V 12 VDD_3.3V VCC1 9 BU
• Y : Parts extracted from the conductor side. WV or less are not indicated except for electrolytics and
VCC2 7
AUDIO_3.3V 13 SW3.3V
• f : Internal component. tantalums.
D305 9
KEY BOARD (2/2) EXT 15 AMP_REM • : Pattern from the side which enables seeing. • All resistors are in Ω and 1/4 W or less unless otherwise
DRV_6V 3 CD_6V (The other layers’ patterns are not indicated.) specified.
LCD_DATA 48 LCD_SO
11 V6IN • f : Internal component.
LCD_CLK 46 LCD_CLK
MECHA_ON 82
Caution: • C : Panel designation.
LCD_CE 47 LCD_CE Pattern face side: Parts on the pattern face side seen
D500
TU_5V 1 TU5V (Conductor Side) from the pattern face are indicated. Note: The components identified by mark 0 or dotted
SIRCS 64 SIRCS
Parts face side: Parts on the parts face side seen from line with mark 0 are critical for safety.
FP_B+ 5 ILM_9V
(Component Side) the parts face are indicated. Replace only with part number specified.

CTRL1
CTRL2
KEY_1 78 KEYIN1
KEY_0 79 KEYIN0
• Indication of transistor. • A : B+ Line.
63 KEY_ACK1 8 6
• Power voltages is dc 14.4V and fed with regulated dc
RE_1 72 RE_IN1 CTRL1_C 30 C power supply from ACC and BATT cords.
RE_0 73 RE_IN0 CTRL2_A 31 • Voltages and waveforms are dc with respect to ground
Q These are omitted.
CTRL2_C 33 under no-signal (detuned) conditions.
PANEL_SW 90 NOSE_SW B E no mark : TUNER (FM)
VBUS DC/DC
USB_VBUS SWITCH CONVERTER ( ): CD PLAY
IC1304 IC1301 * : Impossible to measure
Note: When the complete MAIN board is replaced, the • Voltages are taken with VOM (Input impedance 10 M).
FLT 18 destination setting is necessary. Refer to “NOTE OF Voltage variations may be noted due to normal production
REPLACING THE COMPLETE MAIN BOARD OR tolerances.
EN_USB 17 SYSTEM CONTROLLER (IC501)” on page 4. • Waveforms are taken with a oscilloscope.
SYNC_OUT 25 Voltage variations may be noted due to normal production
tolerances.
VCC • Circled numbers refer to waveforms.
D350 D351 • Signal path.
F : AUDIO
BACK UP BATTERY f : TUNER
BU_IN 35 VOLTAGE DETECT CHECK J : CD
Q300, 302 Q301
E : AUX
d : USB
ACCESSORY 13
ACC_IN 51 CHECK ACC Note: When the complete MAIN board is replaced, the
Q304
destination setting is necessary. Refer to “NOTE OF
REPLACING THE COMPLETE MAIN BOARD OR
SYSTEM CONTROLLER (IC501)” on page 4.

CDX-G3100UE/G3100UV/G3150UP/G3150UV
17 17
CDX-G3100UE/G3100UV/G3150UP/G3150UV

4-3. PRINTED WIRING BOARDS - MAIN Section (1/2) - • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11

A
MAIN BOARD (COMPONENT SIDE)

FB800

FB801 FB802

C321
C305

B FB810

R213
R211
R210
C212

R214
C213
R212
R1355
R1356

C207 C1359
R434
C300 K C202 R432 C422
R203 C201 C209 C404 C406
C204 C200

R316
D353
R1360 C208

R1357
Q301 R312 C301 A A C1376 8

IC403
C1362

D350

D351
A A C319 C324 1 E E E

C306
C304
C303
C302

D1302
D303 C316
C325 C320 C326 R1354 Q410 Q405 Q406
A A K E R309 4
E R310 K C307 R1359 5
K KE K
A K D305 A C251 R433 R416 R407 R408
R1332 C317 C260 CAM002

C323
C322

R364 C309 C308

R361 C315 C314
R363 C311 C310
R362 C313 C312

C416 R422

C402 R404

C407 R411
D302 D301 D300 R315

R308
R311
Q300 Q304 R313 C210

R301

R302
C423
C C253

R427
R314
K K A C1371 R423
Q411
A D200 K
R418
C418 IC402
IC401

R424
C206 C405

R425
C420
R406
E
C415 1 8 (CHASSIS)
Q412 8

R417
1 C401 R412 C409

R428
E 4 5 R402 R414
R431 R426 R429 R401 4 5

R413
R600 C1381 C411 C1379
R1353 R403 C400 C410 R415

C725
E C1360 R419 R11
C211 C421
C1378 Q413
FB803 C753 R421 C412
JL708 C651
R1352 CL602 R1361
C703
D C652

R603
CL681

X701
R400 R714 JL712 JL707 C613

C625

C626
C723 C1377 CL682 C653
C726
JL706

C614
C616
C617
C618
C640
C639
C450 64 R1343 30 C609 1

C720
R710 49 C631
Q408
C719 1 48 31 100

JL702
E C710 C600 R604
A K Q409 R704 C636
C711
IC601

CL604
D400 CL678
Q407 R732 R702

CL605
E E R621
R701 R622
C702
IC701 FB807
CL603
R623

C603 C601
C714 C632

C604
R700 C715

C641
C634
R707
E C713
C1369 JL704
CL674 C1368
X701 C721
16 33 R720 C602 50 81 R624 4 1 IC602
C722 C724 C734 C630
C752 17 51 80
C727 32

CL692
E JL705 CL693 CL691 C1374 C633 C627 R625 C637

FB808
C729 R717
C728 R1346

R716
CL694 C705 R1358 R620 5 8

R614
Q700 C615 R612 R616
R735 R1333
C712 R703 R729 C619 C629

C730

R715
R705 C650 C620
R613 C624 C628 R615 FB806
R1363

CL689
CL687
JL701
C718

CL690

R608
R609
CL688
C706 X601 C13
JL700 FB805 R19
R610 L10

F 1 R1350 R611
CL645 R560

R551
R548

R543
R536
R535
C522
C523
R537
R539
C550 C531 R556
R1334
C701

CL504
75 CL646 51 CL505

CL503
R519 R525
C501 R529
76 50 R526
C717
C520 R527
R514 C502 R520 R530
FFC1 R517 R523 R572 C1361
CN704 R531
R521 R503
SENSOR SERVO R532 C521 R573
R502
BOARD BOARD
R533
R524
R528 IC501 R574
R575
R1335 R522 C532 R15
G CD MECHANISM
OPTICAL
C551
C533
R568

R569
C534
C535 R14
PICK-UP R1336
DECK BLOCK R506 R512
BLOCK R1338

R561
(MG-101CF-188) R1337

R584
R583

R570
(DAX-25A) R1339 100 26

R500
C526
1 25 R563 R576
R511

R1340

R1341
R540 R544
C524 R577
R1364

C700
C750 R1362 C1386 JL714
C1380 R581 C1370
27 E
D503

CL665
CL667
FB811
C528

R545
C527
R542
FB804 R300
K A
Q302

R1310
C1309
C1354

C530
R1309 X502
IC13014

CL664
CL666
CL668
5 C1307

R1308

R546
R549
R554
R565
H

R1303
R1331
C1306 C115
R505
8 1
L1301
C1350 C1301 A D1301 K
A

C1317
D500
C1300 C1316 C1321
3 1
K
R1326 IC1304
4 6
R1323 R1324 R102 R103
C1353
I C1305 L105
C100 R104

C101 R105 R106

C1326 FB100 CAM001
D109 R107
R1312 K C102
FB104

C105
R1311 11
C1323 D152
A FB105 1-893-645- (11)

D110
(CHASSIS)
J

Note 1: When IC501 on the MAIN board is replaced, the destination setting Note 2: IC1301 on the MAIN board cannot replace Note 3: The service manual of the mechanism deck, used in this model,
is necessary. Refer to “NOTE OF REPLACING THE COMPLETE with single. When this part is damaged, replace has been issued in a separate volume. Please refer to the service
MAIN BOARD OR SYSTEM CONTROLLER (IC501)” on page 4. the complete mounted board. manual of the MG-101 series for the mechanism deck information.

CDX-G3100UE/G3100UV/G3150UP/G3150UV
18 18
 CDX-G3100UE/G3100UV/G3150UP/G3150UV
Ver. 1.1
4-4. PRINTED WIRING BOARDS - MAIN Section (2/2) - • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13
MAIN BOARD (CONDUCTOR SIDE)
J401 CN301
AUDIO OUT
REAR
A J801
(REMOTE IN)
FU1
SUB L R

(G3150UP/G3150UV)
J01 PW1
(ANTENNA IN)
L300 GRN
1 2 REAR LCH (+)
CL699 VIO
REAR RCH (+)
GRN/BLK
3 4 REAR LCH (–)
VIO/BLK
REAR RCH (–)
A002 WHT
5 6 FRONT LCH (+)
B TO
CN301
GRY
WHT/BLK
FRONT RCH (+)
14 IC201 2 24 IC300 2 2 14 16
7 8
GRY/BLK
FRONT LCH (–)
FRONT RCH (–)

W001
9 10
15 BLU/WHT
REM OUT MAX 0.4A
15 1 1 13
11 12
25 1

13 14
RED
ACC
JL724 JL723 JL719 JL720 BLK
15 16 GND
CL695 JL722 YEL
JL721 BATT

C C350
(G3100UE/G3100UV)

RL+ RL–
GRN GRN/BLK
7 8
FL+ FL–
WHT WHT/BLK
5 6
11 FR+ FR–
GRY GRY/BLK
(11) 3 4
1-893-645-
JL755 RR+ RR–
VIO VIO/BLK
D JL753
1 2

CL679
TO
PW1
CN301
CL609 CL683
CL635 CL680 VIO GRN
1 1 2
CL611 CL610
CL675
CL612 VIO/BLK GRN/BLK
3 4
CL634 CL676
CL677 JL703 GRY WHT
5 6

TU01 GRY/BLK WHT/BLK

TUX-DSP04 CL621 7 8
E (TUNER UNIT)
CL623 BLU/WHT
CL607 CL624 9 10
CL606 CL622
CL608
CL617 JL752 11 12

CL627 JL685 RED

8 13 14

JL751 YEL BLK

15 16
CL629 JL686
JL756
CL628

CL647 JL728 ACC GND

F CL619
JL727
JL729
RED
7 8
BLK

JL734 AMP
BLU/WHT REM NC
5 6
JL732 JL730
CL642 JL731 NC BATT
YEL
3 4
CL641 JL736 NC NC
JL735
JL718 1 2
JL717 JL737
JL738
JL716 JL733
JL502 JL740
JL739
JL715 JL741
G CL601
JL742
JL748
JL501 JL743
JL746
CL501 CL600 JL744
CL697
CL502 JL750 JL747 JL745
JL749
CL500
X501
JL503

CL698

I
CL069

CL071

CL073
CL075

CL077

CL079

CL064

CL066
CL068

CL072

CL074

CL076

CL078

CL081

CL065
CL070

CL063
CL061

CL067 2 20

1 19

CN101

Note: When the KEY board is defective, replace the

KEY
BOARD
FRONT PANEL OVERALL ASSY (Ref. No. FP1).

CDX-G3100UE/G3100UV/G3150UP/G3150UV
19 19
 CDX-G3100UE/G3100UV/G3150UP/G3150UV

4-5. SCHEMATIC DIAGRAM - MAIN Section (1/3) - • See page 23 for Waveforms. • See page 25 for IC Pin Function Description.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

MAIN BOARD (1/3)

A

JL751

C703
15p 4 3 2

BEEP

STBY
RC_IN0

RC_IN1

AMP_MUTE

ACC_IN
DATA

B
7
BCK JL756
6 R714
X701 470
16.934MHz LACK

5
5 R503
R603 470 R556
MCLK 100k
>101S 4 100k

KEY_0
KEY_1
RE_1

RE_0

SIRCS
3
MAIN R536 R539 R543
BOARD 2 33k 33k 100k
D500
(3/3) R702 R704 C720 C726 C753 C725 C723 C734 LRB751V-40T1G
1
(Page 22) 16
10k 68k 0.047 0.1 100
4V
0.1 0.1 0.1 FB803
C706
1000p
C550
220
6.3V
C531
0.01

JL712
C R535 R537 R551 R548 R560

C523
CD_BUSYB

0.01
C522 1k 1k 100k 100k 100k
0.01

JL706

JL707
JL708
CN704 R1343
27P 1k

(1.8)
(3.5)

(1.8)

(1.7)

(3.5)

(1.6)

(3.5)

(1.3)

(1.8)

(1.8)

(1.8)
(3.4)
JL727 B
B 1
JL728 A
A 2 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
JL729
1
C

XOUT
SLCO
XVDD
XIN

XVSS

DVDD
DVDD15
MODE
SMOIN2
SMOIN1

SMOIN0
DATA

BCK
LRCK
MCLK

BUSYB
C 3 C711 C501

S-GAIN_C
S-GAIN_B

S-GAIN_A
JL730 E 0.1 R710 JL753 JL752 1000p
E 4
JL731 F 330 (1.9) (3.4) CL679 CD_RESB

D
F 5 1 EFMIN RESB 48

CL647

CL642
CL641
JL732 JL702 (1.8) (0.1) CL680 CD_DO
C710 R519
OP_VCC 6 0.01 2 RFOUT DO 47
10k C532
JL733 C719 4700p (1.8) (3.4) CL681 CD_DI 0.01
1/2VCC 7 3 LPF DI 46
JL734 (2.4) (3.4) CL682 CD_CL
OP_GND 8 4 PHLPF CL 45 C520

CL646
CL645
JL735 B (2) (0.1) CL683 CD_CE 1000p C1361
PD 9 5 AIN CE 44 0.1
JL736 R732 0 (1.9) (0.3) CL678 SBCK
CD MECHANISM LD 10 6 CIN SBCK 43

0.1

0.1

3.4

0.1

3.4

3.5

3.5

0.1

3.4

3.4

3.5

3.5

0.1

0.1

3.5

0.1
DECK BLOCK A (2) (0.2) CL677 PW
IC701
R520
(MG-101CF-188) FFC1 DRV_VREF 11 7 BIN PW 42
10k
JL737 EJECT C (1.9) (1.8) CL676 SFSY 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
EJECT 12 8 DIN SFSY 41
JL738 CL675

BEEP

ATT

TELATT
NC

NC
RE_IN0

RE_IN1
RE-ON

NC
NC

DUBUG_7
DUBUG_6

NC
SIRCS

KEY_ACK1
KEY_ACK0

S-GAIN_C
S-GAIN_B

S-GAIN_A
AMPSTB

AMP_MUTE

NC

VSS3
VDD3
ACC_IN
SENSOR SERVO FOCUS (1.9) RF AMP, DIGITAL SERVO PROCESSOR (0.2) SBSY 17

E FOCUS 13
BOARD BOARD 9 SLCISET IC701
SBSY 40 C521 C502
JL739 TRACK (3.5) CL674 OPCDM 0.01 1000p 18
C714 JL703 LC78615E-01US-H
TRACK 14 0.1 10 RFMON OPCDM 39
JL740 DRV_ON JL700 (1.8) 76 NC NC 50 20
DRV_ON 15 11 VREF NC 38 R529 R525
JL741 SELF C715 0.01 (0.1) 77 NC NC 49 22
SELF 16
JL742 IN_SW F R700 3.3k (2.1)
12 JITTC NC 37
(3.4)
R523
10k
100 3.5
78 KEYIN1 LCD_SO 48
0.1 CL505 1k
23
>102S
IN_SW 17 13 EIN L_SW 36 R530 100 3.5 0.2 CL504 R526 470
OPTICAL JL743 LOAD E R707 0 (2.1) (0.1) 79 KEYIN0 LCD_CE 47 24 MAIN
PICK-UP LOAD 18 14 FIN TEST 35 R521
R531 100 3.5 3.4 CL503 R527 1k BOARD
BLOCK JL744 SL R701 JL704 (1.8) 80 RC_IN0 LCD_CLK 46 25 (2/3)
100k R532 100 JL718
(DAX-25A) SL 19 3.3k 15 TE DVSS 34 3.4 0.1 SMONI

SP 20
JL745

JL746
SP
C700
0.1
C701
0.1
(1.8)
16 TEIN DVDD 33
(3.5)
3
81 RC_IN1 WDT_MON 45
0.1 R572 100 USB_IN
26
(Page
21)

PDOUT1

PDOUT0
82 MECHA_ON USBIN 44 27

DVDD15
PCKIST
C721

VVDD1
R573 100

VVSS1
F BU_GND 21 R524 3.5 SYSRST

SPDO
SLDO
AVDD
AVSS
JL747 0.01

FDO

TDO
LDD
D_SW 30k 83 NC SYSRST 43

LDS

NC
NC
D_SW 22 0.1 R574 100 CE
JL749 C702 C1369
L_SW 0.1 84 NC CE 42
100p R575 100
L_SW 23 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 0.1 CMD_ERR
JL748 85 VSS4 CMD_ERR 41
DRV_GND 24 3.5 R502 100k
(3.4)
(2.6)

(0.3)

(1.8)
(1.8)

(1.7)

(1.9)

(1.3)

(1.3)
(1.3)

(3.4)

(1.6)
JL717 R568
86 VDD4 NC 40
IC501 JL716 100 C534 47p
DRV_GND 25 C750 3 LITHIO_DATA
JL750 87 NC LITHIO_DATA 39
100
DRV_6V 26 16V 3 JL715 R569 100 C535 47p LITHIO_CLK
R522 88 NC SYSTEM CONTROLLER LITHIO_CLK 38
100k C533 0.01
DRV_6V 27 R528 IC501 3.5
89 NC VDD2 37

680

680
100 LC88FC2H0AF2314-2H R577 220k
R735 C728 R720 PANEL_DET 0.1
CL694
CL693
CL692
CL691
90 NOSE_SW VSS2 36
JL701 3.3 R703 0.1 33k JL714
G 3.4
C551 BUIN

R717

R716
470 R517
100k 2.2 91 NC BU_IN 35
3.3 R576 0 BUSY
JL685 R1335 92 NC BUSY 34
Q700 C718 R1350 100 R570 10k
2SA1037AK-T146-R 1000p 100 D_SW (0.1) 3.5 CTRL2
68k

93 MEC_DSW CTRL2_C 33
R705 R1336 100 R581 100k
AUTOMATIC 1
C730 0.022 L_SW (3.4) R583
POWER CONTROL 94 MEC_LSW CTRL2_B 32
R729

4.7k
C729 0.22

R506 1k 2.1 3.5

C705
0.1 95 FILT CTRL2_A 31
1.9 3.3 JL686 LOAD R1337 100 (0.1) 3.5 CTRL1
0.1

68k
96 MEC_LOAD CTRL1_C 30
IN_SW R1338 100 (3.4) R584
C713 C724
C712
CL687
CL688

CL689

CL690
JL705

2.6 C727 97 MEC_INSW CTRL1_B 29 22

0.1 0.1
R715

FB805 0.1 SELF R1339 100 (3.4)

C717
0.1 98 MEC_SELFSW CTRL1_A 28
R1340 100
H
DRV_ON (3.4) 0.1 TXD1
99 DRV_ON TX 27
EJECT (0.1) 3.4 RXD1

SYNC_OUT
100 MEC_EJECT RX 26

DEBUG_1

DEBUG_2
DEBUG_3

DEBUG_4
DEBUG_5
C752 C722 R1341

EN_USB

EN_SYS
220 0.1

RESET
FOCUS

100
TRACK

VDD1
TEST

VSS1
4V R511

SDO

SCK
R563

CF1
CF2
XT1
XT2

FLT

SDI
100k

NC

NC
NC

NC
NC
100k
SP
SL

R512 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
100k
R561

0.1

3.4
1.5

1.7

1.5

1.2

3.5

3.3

3.3

3.3


3.3

1.7
100k
R514

CL664
CL665

CL666
CL667

CL668
100k

I JL503
R533 R1331 C1380 R1364

CL697

CL500
CL501
33k 100 2.2 100
JL502
C526

100k
0.1

10k

CL502
FB804

100k
R546

R549
7

R554
6 R1362 R565

C1386
47p
0 68k
J

SDO

SCK
R540 R544

SDI
10M 1M

FB811
R542 R545
220k 0
X502
9.25MHz

1 3

CL698
X501
32.768KHz

4 2

RB520SM-30T2R
K

D503
R505 C524 C527 C528 C530

FLT_USB
100k 18p 20p 2p 2p

EN_USB
R500

SYNC
100k

JL501

Note 1: When IC501 on the MAIN board is replaced, the destination setting is necessary. Refer to “NOTE OF Note 2: The service manual of the mechanism deck, used in this model, has been issued in a separate volume.
REPLACING THE COMPLETE MAIN BOARD OR SYSTEM CONTROLLER (IC501)” on page 4. Please refer to the service manual of the MG-101 series for the mechanism deck information.

CDX-G3100UE/G3100UV/G3150UP/G3150UV
20 20
 CDX-G3100UE/G3100UV/G3150UP/G3150UV

4-6. SCHEMATIC DIAGRAM - MAIN Section (2/3) - • See page 23 for Waveforms. • See page 24 for IC Block Diagrams. • See page 25 for IC Pin Function Description.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

MAIN BOARD (2/3)

A
17
18 L105
2.2uH
19
20 8
>102S 22 9
MAIN 23 10
BOARD
(1/3) 24 11
>103S
R1353
B (Page 20) 25
C1377
1
0
12 MAIN
BOARD
26 13 (3/3)
27 14 (Page 22)
15

R600
0
R19
0 R107
C CD_DI C651 C652
2.2k

220 47 R106
CD_CL 6.3V 6.3V R1361

C625 10

C626 10
15k
0

C614 1
C616 1

C617 1
C618 1
C640 1

C639 1
CD_DO
CD_CE C609 C613 R105 C101
2.2 0.1 4.7k 1000p

C650 R104 C100

100 4.7k 1000p

CL602
10V
D

(0.1)
(0.1)

(3.4)
(3.4)

3.4

1.8

1.8
1.8
1.8
1.8
1.8

1.8
1.8
1.7
1.8
1.8
1.7

1.7
1.7
1.8
1.8
1.8
C653 R103
C600 100 15k
0.1 16V
30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

CD_CL

DACOUT_L
VREFOUT

R3_IN_P

L3_IN_P

RFOUT
RROUT

LROUT
LFOUT
CD_CE

CD_DO

CD_DI
NC
NC
NC

NC

AVDD2

AVSS2
VREF_ADC

ATEST02(OPN)
ATEST01(OPN)
R3_IN_N

L3_IN_N

R2_IN

L2_IN

R1_IN
L1_IN

RVRIN

DACOUT_R

LVRIN
R102
R604 2.2k
C602 0 C631
0.1 0.1
3.4 1.8 C636
31 DVDD LRREF 100 0.047
32 DVSS AVSS1 99
3.4
CL609 33 GP30(NCO) AVDD1 98

E CL610 34 GP31(NCO) TEST1(GND) 97

CL611 35 GP32(NCO) JTRTCK(O) 96 CL635
CL612 CL634 R620 C632
36 GP33(NCO) JTDO(O) 95 47k 47
SBSY (0.2) 3.4 CL606
C603 37 SBSY JTMS(IPU) 94
0.1 SFSY

PW
(1.8)
(0.2)
38 SFSY JTDI(IPD) 93
0.1
0.1
CL605
CL604
R621
R622
47k
47k
IC602
39 PW
IC601 JTCK(IPD) 92 EEPROM
SYNC

EN_USB

FLT_USB

C601 SBCK (0.3) 0.1 CL603 R623 47k

FB807 IC602
0.1 40 SBCK JTRSTB(IPD) 91
MFI337S3959
C1350 3.4 USB CONTROLLER, INPUT SELECTOR, 1.6 C641
47 41 DVDD AUDIO DSP, ELECTRICAL VOLUME DVDD15 90 0.1
F 16V
C604
42 DVSS
IC601
LC786800E-6C07-H
DVSS 89
3.4 3.4
47 43 REG1_EXTR(OPN) DVDD 88 1 GND VCC 8
C1309 L1301 1.6 3.4
C1306 47uH DVDD15 TEST0(GND) 87 2 SDA RST 7
1 44
IC1301
0.01 CL600 CL623
RXD1 3.4 0.1 3.4
45 TXD1 CMD_ERR 86 3 NC SCL 6
TXD1 CL601 0.1 (3.4) CL607
C1301 DC/DC CONVERTER 46 RXD1 CD_RESB 85 4 NC NC 5
SMONI CL617 0.1
1 IC1301
8
BD9876AEFJ-BZE2 47 SMONI CP_RESET 84
OPCDM (3.5) 3.4 R624 2.2k
48 OPCDM CP_SDA 83
R1333
3.4 3.4 R625 2.2k
C1300 R1308 0
4.7 47k 49 DVDD CP_SCL 82

G 13.9 5.3 3.4

GP45(NCO)
GP46(NCO)

GP47(NCO)
CD_BUSYB
8 VCC Lx 1 50 DVSS DVDD 81 C637
10

RESETB

X12OUT
0.1

USB_IN
BUSYB

VVDD2
VVDD3
SIFDO
7 BST GND 2

SIFCK

SIFCE

DVDD

UDM1

UDM2
MCLK

XVDD
X12IN
DVSS

DVSS

DVSS
LRCK

UDP1

UDP2

XVSS
AFILT
SIFDI

DATA
R1309

BCK
3.4 1.3
6 EN VC 3 3.3k
1.8 1.1 C634
5 SYNC FB 4 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 0.1
C1307

3.5
3.5

0.1
3.3
(3.4)
(1.8)

(1.8)
(1.3)
(1.8)
0.1

3.3

3.4
0.1
0.1

0.1
0.1
3.4
1.7
1.7

2
3.4
3.4
0.01
DB2441600L

C630
D1301

CL622
0.1

15k
15k
R1303 R1310
4.7k 12k

R612
R613
C627
0.1

CL624

CL627

CL628

CL629
CL608

CL619

CL621
CAM001
(CHASSIS)

FB808
IC1304 C615 R1363 C1374 R1358

R1346
0

4.7k
2.2 0 0.1 C1368
0.1
VBUS SWITCH
IC1304
BD2242G-GTR C620
5p C619 C102
5p R614 X601 R615 R616 2.2
5.3 5.3
1 VIN VOUT 6 1M 12MHz 3.3k 4.7k

I 2 GND ILIM 5
0.5 R608
15
R609
15
2 4

FB100

FB104
FB105
R1324 R610
5.3 3.4
22k 15k
3 EN /OC 4
CN101
R1326 R1323 3 1
10k
CD_BUSYB 20P
51k C624 C628 C629 C633 CL061

CD_RESB
SYSRST

R611 12p 12p 3300p 220p

USB_IN
C1353 1 USB_GND
15k

CMD_ERR
MCLK
CL063
BUSY

LACK

DATA
100
SDO
SCK

BCK
SDI

2 USB_VBUS
CE

16V
CL066
C1316 C115
10 1 3 GND
CL067
C1305 4 KEY_GND
D109 CL068
J C1317
10
22
D110 CL069
5 AUX_L

C1354 6 AUX_R
CL070
C1323 1
2.2 7 AUX_GND
RE_0 CL071
C1321 D152
1 DZ2J06800L 8 RE_0
RE_1 CL072
9 RE_1
R1311 CL073
1k KEY_1
10 KEY_1 KEY
KEY_0 CL074
BOARD
11 KEY_0
SIRCS CL075
R1312
1k 12 SIRCS
CL076
K CL077
13 LCD_DATA
14 LCD_CE
CL078
15 LCD_CLK
CL079
16 ILL(FP+B)
PANEL_DET CL081
C105
17 PANNEL_SW
10 CL064
R1334
0 18 D–
CL065
19 D+
L 20 GND
C1326
47p

Note 1: IC1301 on the MAIN board cannot replace with single. When Note 2: When the KEY board is defective, replace the
CDX-G3100UE/G3100UV/G3150UP/G3150UV this part is damaged, replace the complete mounted board. FRONT PANEL OVERALL ASSY (Ref. No. FP1).
21 21
 CDX-G3100UE/G3100UV/G3150UP/G3150UV
Ver. 1.1

4-7. SCHEMATIC DIAGRAM - MAIN Section (3/3) - • See page 24 for IC Block Diagrams.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
(G3150UP/G3150UV)
MAIN BOARD (3/3)
IC300 IC201
PW1
A

PRE_GND(BEEP)

PW_GND3(RR)

PW_GND4(FR)
PW_GND1(RL)
PW_GND2(FL)

AMP_REM

VDD_3.3V
REAR RCH (+) 1 2

AC_GND
POWER AMP REGULATOR

TU5V_F
RIPPLE

ILM_9V

SW33V
CD_6V

CTRL2

CTRL1
IN_RR
IN_FR
IN_RL

MUTE

ILM_F
IN_FL
VCC2

VCC1

VCC2

VCC1
STBY

TU5V
REAR LCH (+) IC300 IC201

GND

V6IN
RR+

RR–

ANT

EXT
FR+

FR–
TAB

RL+
RL–
FL+
FL–
PURE5001H LV56841
REAR RCH (–) 3 4
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
REAR LCH (–)

7.2

3.3

7.2

13.9

7.2

7.2

3.6

3.6

3.6

3.7

3.6

3.6

7.2

7.2

13.9

7.2

3.7

7.2

1.3

6.1

1.3

9.1

3.3

13.9

3.3

13.3

6.1

3.4

3.3

13.9
FRONT RCH (+) 5 6
TO
FRONT LCH (+) CN301
FRONT RCH (–) 7 8

B FRONT LCH (–)

R1352
REM OUT MAX 0.4A 9 10
0

1000p
R212

C212

C206

C201
0.22
33k

10
R1354

R1355

R1356

R1357

FB810
11 12

470

470

470

470
D305
GN1G

1000p
C213

R210

470 16V

220 16V
24k
ACC 13 14

C253

C210
C307

C308

C310

C312

C314

C316
R203

10

1
CN301 0

GN1G
D200
BATT 15 16 16P

CL695
JL719
C GND GND 16
JL720

C309

C313

C315

C317
C311
BU 15 R312 R361

1
10k 220
(G3100UE/G3100UV) TLL_ATT 14
JL723 R362 220
ACC 13
JL724 R310 R311 R363 220
RL+ RL– NC 12 10k 47k
7 8 L300 D300
D353 R364 220
11 140uH GN1G JL721 JL722
ILL DZ2J18000L

FL+ FL– NC 10
5 6
AMP_REM 9

D FR+ FR– FL– 8

R214
3 4

1k
FR– 7

C324
1
RR+ RR– FL+ 6

C207
1 2

1
FR+ 5

R213

R211
3.9k
10k
RL– 4

TO RR– 3
C209

C204
CN301

0.22
2 10
PW1 RL+

RR+ RL+ RR+ 1

E
1 2

C202

C200
10

10

100 16V
C211

C260
C325 C350 D301 D302 R301 C300 R302 C301 R309 R308 R1359 100
RR– RL– 0.1 3300 GN1G GN1G 1k 0.1 1k 1 47k 4.7k C326 0 16V
3 4 FB802 1
FU1 16V
10A

R400
220 16V

220 16V
32V

22
FR+ FL+

C1378
C251
5 6 FB801 D350 D351 R1360 R315
DZ2J07500L DZ2J18000L 0 150 C1359
J801 1000p
(REMOTE IN) CL699
FR– FL–
7 8 FB800 0.1

0.7

C303

C305

C304

C306

C319

C320

C321

C322

C323
47p

47p

47p

47p

47p

47p

47p
F REM OUT

1
9 10 Q304
LSCR523UBFS8TL C302 C1376 C1371 D303
6.4 0.1 47p
ACCESSORY CHECK 47p 0.1 GN1G
Q301
6.4 LTC014EUBFS8TL
11 12
BATTERY CHECK C208 R313 R314 C450
10 10k 47k 47 Q407
ACC 25V LTA014EUBFS8TL
13 14
0.1 C1370
Q300 1000p 13.7 0.1
BATT GND LTC044EUBFS8TL
15 16
R316 D1302 D400
47k DA2J10100L DA2J10100L
0.1

G R300 Q302 13.7

Q407 - 409
220k LSCR523UBFS8TL
3.3 MUTING CONTROL
16
ACC GND 0.1
7 8 1
2 Q409 0.1
AMT REM Q300, 302
5 6 >101S 3 BACK UP VOLTAGE DETECT R1332
LTC014EUBFS8TL

100
4
BATT MAIN
3 4 BOARD L10 Q408
5 FB806 4.7uH LTA014EUBFS8TL
(1/3)

AMP_MUTE
H (Page 20)
6 0.1
ACC_IN
RC_IN1

RC_IN0

CTRL2

CTRL1
BEEP
STBY
1 2 7
BUIN

8
9
10

>103S 11 J401
4P
12
MAIN
I BOARD
(2/3)
13
R
14
(Page 21) 15 REAR
C404 C406
19 47p 47p
L
AUDIO OUT
Q405 Q406 Q410
LTC014TUBFS8TL LTC014TUBFS8TL LTC014TUBFS8TL
R416 SUB
MUTING MUTING 10k MUTING
0.1 0.1 0.1

J
J01
0 0 0 (ANTENNA IN)

R407 R408 JL755

10k 10k
R427
Q411 10 C1379 C1362
LTC014TUBFS8TL 0.1 1000p R11

IC401 IC402 IC403

0
GAIN CONTROL R423 R404 R411 R422
0.1 100k 680 680 1k

K
LINE AMP LINE AMP CENTER VOLTAGE GENERATOR
IC401 IC402 IC403 RF_GND_PLATE1
0
C402 NJM8065RB1-TE1 C407 C416 NJM8065RB1-TE1 NJM8065RB1-TE1 R434 RF_ANT_IN
4.7 4.7 10 10 1 RF_GND_A
3.4 5 9 5 9 5 9 RF_GND_B
2
1 V+ 8 1 V+ 8 1 V+ 8 1.7
S-GAIN_A C401 R406 AUDIO_OUT_L
220p 12k 5.1 5.1 5 5 3
5.1 5.1 1.7
2 7 2 7 2 7 AUDIO_OUT_R
Q412 R412 C409 C415 R425 C420 4
LTC014TUBFS8TL R401 5 5.1 12k 220p 0.1 5 5.1 18k 220p 5 5 R14 RSTN
10k R432 0 5
GAIN CONTROL R424
3 6 3 6 3 6
10k
LITHIO_CLK 3
R402 R414 R417 SCL
0.1 56k 100 5 10k 6.8k 5 5 LITHIO_DATA 2.9 6 AUDIO_GND
4 V– 5 4 V– 5 4 V– 5 SDA
R418 R428 7 POWER_GND
L R413 R415 R15 4.9
6.8k 3.3k +5V
100 100k 0 8
R403
100k POWER_GND_PLATE1
3.4

S-GAIN_B C400 C410 R426 R429 TU01

1 1 100 100k
Q413 C13 TUX-DSP04
LTC014TUBFS8TL 0.1 (TUNER UNIT)

GAIN CONTROL R431 C421

0.1 18k 1
C412 C411
2.2 2.2

0.1 R421 R419

100k 100k
M S-GAIN_C
C405
0.1
C1381
0.1
C1360
0.022
C418
10
C423
10
R433
12k
C422
10
CAM002

(CHASSIS)

CDX-G3100UE/G3100UV/G3150UP/G3150UV
22 22
 CDX-G3100UE/G3100UV/G3150UP/G3150UV

• Waveforms

– MAIN Board –

IC701 2 (RFOUT) IC501 0 (CF2)

1 (CD play mode)
7

3.1 Vp-p
1.2 Vp-p 110 ns
500 mV/DIV, 1 Ps/DIV 1 V/DIV, 50 ns/DIV

IC701 t; (MCLK) IC1301 1 (Lx)

2 8

3.4 Vp-p 14.6 Vp-p

60 ns 2.6 Ps

1 V/DIV, 50 ns/DIV 5 V/DIV, 1 Ps/DIV

IC701 ta (LRCK) IC601 ug (X12OUT)

3 9

3.3 Vp-p 2.68 Vp-p

22.6 Ps 83 ns
1 V/DIV, 10 Ps/DIV 1 V/DIV, 50 ns/DIV

IC701 ts (BCK)
4

3.28 Vp-p
472 ns

1 V/DIV, 200 ns/DIV

IC701 ya (XOUT)
5

2.48 Vp-p
60 ns
1 V/DIV, 50 ns/DIV

IC501 7 (XT2)
6

2.2 Vp-p
30 Ps

1 V/DIV, 20 Ps/DIV

23
CDX-G3100UE/G3100UV/G3150UP/G3150UV

• IC Block Diagrams

– MAIN Board –
IC201 LV56841PVD-XH

OVP ALL OUTPUTS EXCEPT VDD: OFF

OVP
TSD ALL OUTPUTS: OFF

OVP
6.5V

VREG 5.8V

VREF 1.25V

TSD
OVS
VREG
CTL
– VREF – VREF VREF – OVP + VREF – VREF ANT EXT
+ + + TSD – + OUT OUT

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

ANT

EXT
ILM

ILM_F

CD

AUDIO_F

AUDIO

CTRL2

VCC2

CTRL1

VCC1

GND

V6IN

VDD

SW3.3V

IC300 PURE5001H-4WX

HIGH SIDE
DRIVER

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
TAB

PW-GND2
OUT2–

ST-BY

OUT2+

VCC2

OUT1–
PW-GND1
OUT1+

SVR

IN1

IN2

S-GND

IN4

IN3

AC-GND

OUT3+
PW-GND3
OUT3–

VCC1

OUT4+

MUTE

OUT4–
PW-GND4

HSD

IC1301 BD9876AEFJ-BZE2 IC1304 BD2242G-GTR

VREF REFERENCE
VIN 1 6 VOUT

LX 1 8 VCC REVERSE CURRENT

GND 2 PROTECTION
REGULATOR /EN
UNDER-VOLTAGE
CURRENT LOCKOUT
SENSE AMP
GND 2
7 BST
CHARGE THERMAL
EN 3 5 ILIM
PUMP SHUTDOWN
UNDER
VOLTAGE 4 /OC
LOCK OUT
OVER-CURRENT DELAY
THERMAL PROTECTION COUNTER
SHUTDOWN
Q SHUTDOWN
VC 3 S R
6 EN
SOFT
START CURRENT
COMPARATOR

ERROR
FB 4 6 OSCILLATOR
AMP 5 SYNC
300 kHz

1.0 V

24
 CDX-G3100UE/G3100UV/G3150UP/G3150UV

• IC Pin Function Description

MAIN BOARD IC501 LC88FC2H0AF2314-2H (SYSTEM CONTROLLER)

Pin No. Pin Name I/O Description
1 to 3 NC O Not used
4 TEST I/O Not used
System reset signal input terminal “L”: reset
5 RESET I
For several hundreds msec. after the power supply rises, “L” is input, then it change to “H”
6 XT1 I Low-speed clock signal input terminal (32.768 kHz)
7 XT2 O Low-speed clock signal output terminal (32.768 kHz)
8 VSS1 - Ground terminal
9 CF1 I High-speed clock signal input terminal (9.25 MHz)
10 CF2 O High-speed clock signal output terminal (9.25 MHz)
11 VDD1 - Power supply terminal (+3.3V)
DEBUG_1 to
12 to 16 O Not used
DEBUG_5
17 EN_USB O USB power on/off control signal output to the DC/DC converter “H”: power on
18 FLT I USB over current detection signal input from the VBUS switch “L”: over current
19 EN_SYS O Power on/off control signal output terminal Not used
20 SDO O Serial data output to the audio DSP
21 SDI I Serial data input from the audio DSP
22 SCK O Serial data transfer clock signal output to the audio DSP
23, 24 NC O Not used
25 SYNC_OUT O Frequency control signal output to the DC/DC converter
26 RX I UART data input from the audio DSP
27 TX O UART data output to the audio DSP
28, 29 CTRL1_A, CTRL1_B O Power on/off control signal output terminal Not used
30 CTRL1_C O Power on/off control signal output to the regulator
31 CTRL2_A O Power on/off control signal output to the regulator
32 CTRL2_B O Power on/off control signal output terminal Not used
33 CTRL2_C O Power on/off control signal output to the regulator
34 BUSY I Busy signal input from the audio DSP “L”: busy
35 BU_IN I Back-up power detection signal input terminal “L” is input at low voltage
36 VSS2 - Ground terminal
37 VDD2 - Power supply terminal (+3.3V)
38 LITHIO_CLK O Serial data transfer clock signal output to the tuner unit
39 LITHIO_DATA I/O Two-way data bus with the tuner unit
40 NC O Not used
41 CMD_ERR I Command error signal input from the audio DSP “H”: error
42 CE O Chip enable signal output to the audio DSP
43 SYSRST O Reset signal output to the audio DSP “L”: reset
44 USBIN I USB device detection signal input from the audio DSP “L”: USB device is connected
45 WDT_MON I Watch-dog timer status monitor input from the audio DSP
46 LCD_CLK O Serial data transfer clock signal output to the front panel block
47 LCD_CE O Chip enable signal output to the front panel block
48 LCD_SO O Serial data output to the front panel block
49, 50 NC O Not used
51 ACC_IN I Accessory power detection signal input terminal “L”: accessory power on
52 VDD3 - Power supply terminal (+3.3V)
53 VSS3 - Ground terminal
54 TELATT I Telephone attenuator detection signal input terminal Not used
55 NC O Not used
56 ATT O Audio muting on/off control signal output terminal “H”: muting on
57 AMP_MUTE O Amplifier muting on/off control signal output to the power amplifier “L”: muting on
58 AMPSTB O Standby signal output to the power amplifier “L”: standby
S-GAIN_A to
59 to 61 O SUB AUDIO OUT gain control signal output terminal
S-GAIN_C
62 KEY_ACK0 I Key acknowledge signal (wake up signal) input from the rotary commander
63 KEY_ACK1 I Key acknowledge signal (wake up signal) input from the front panel block
64 SIRCS I Remote control signal input from the front panel block
65 NC O Not used

25
CDX-G3100UE/G3100UV/G3150UP/G3150UV

Pin No. Pin Name I/O Description

66, 67 DEBUG_6, DEBUG_7 O Not used
68 BEEP O Beep sound drive signal output to the power amplifier
69, 70 NC O Not used
71 RE_ON O Jog dial pulse pull-up signal output terminal
72, 73 RE-IN1, RE-IN0 I Jog dial pulse input from the rotary encoder
74 to 77 NC O Not used
78, 79 KEYIN1, KEYIN0 I Front panel key input terminal
80 RC_IN0 I Rotary commander key input terminal
81 RC_IN1 I Rotary commander shift key input terminal
Power detection signal input terminal for CD mechanism section
82 MECHA_ON I
“H”: CD mechanism power on
83, 84 NC O Not used
85 VSS4 - Ground terminal
86 VDD4 - Power supply terminal (+3.3V)
87 to 89 NC O Not used
90 NOSE_SW I Front panel remove/attach detection signal input terminal “L”: Front panel is attached
91, 92 NC O Not used
93 MEC_DSW I Chucking end detection switch input terminal
94 MEC_LSW I Limit in detection switch input terminal
95 FILT I Filter terminal for PLL
96 MEC_LOAD O Loading motor drive signal (loading direction) output terminal “H”: motor on
97 MEC_INSW I Disc insert detection switch input terminal
98 MEC_SELFSW I Self loading position detection switch input terminal
99 DRV_ON O Driver control signal output to the CD mechanism deck block
100 MEC_EJECT O Loading motor drive signal (eject direction) output terminal “H”: motor on

26
 CDX-G3100UE/G3100UV/G3150UP/G3150UV

MAIN BOARD IC601 LC786800E-6C07-H (USB CONTROLLER, INPUT SELECTOR, AUDIO DSP, ELECTRICAL VOLUME)
Pin No. Pin Name I/O Description
1 LFOUT O Audio signal (front L-ch) output terminal
2 LROUT O Audio signal (rear L-ch) output terminal
3 LVRIN I Audio signal (L-ch) input terminal
4 DACOUT_L O Audio signal (L-ch) output terminal
5 DACOUT_R O Audio signal (R-ch) output terminal
6 RVRIN I Audio signal (R-ch) input terminal
7 RROUT O Audio signal (rear R-ch) output terminal
8 RFOUT O Audio signal (front R-ch) output terminal
9 L1_IN I Audio signal (tuner L-ch) input terminal
10 R1_IN I Audio signal (tuner R-ch) input terminal
11 L2_IN I Audio signal (L-ch) input terminal Not used
12 R2_IN I Audio signal (R-ch) input terminal Not used
13 L3_IN_P I Audio signal (AUX L-ch) input terminal (positive)
14 L3_IN_N I Audio signal (AUX L-ch) input terminal (negative)
15 R3_IN_P I Audio signal (AUX R-ch) input terminal (positive)
16 R3_IN_N I Audio signal (AUX R-ch) input terminal (negative)
ATEST01 (OPN),
17, 18 O Analog test output terminal Not used
ATEST02 (OPN)
19 VREFOUT O Reference voltage output terminal Not used
20 VREF_ADC O External capacitor connection terminal for audio A/D converter reference voltage
21 AVSS2 - Ground terminal (analog system)
22 AVDD2 - Power supply terminal (+3.3V) (analog system)
23 to 26 NC - Not used
27 CD_DI O Serial data output to the digital servo processor
28 CD_CL O Serial data transfer clock signal output to the digital servo processor
29 CD_DO I Serial data input from the digital servo processor
30 CD_CE O Chip enable signal output to the digital servo processor
31 DVDD - Power supply terminal (+3.3V) (digital system)
32 DVSS - Ground terminal (digital system)
GP30 (NCO) to
33 to 36 I/O Not used
GP33 (NCO)
37 SBSY I CD sub-code block sync signal input from the digital servo processor
38 SFSY I CD sub-code flame sync signal input from the digital servo processor
39 PW I CD sub-code PW data input from the digital servo processor
40 SBCK I CD sub-code data transfer clock signal input from the digital servo processor
41 DVDD - Power supply terminal (+3.3V) (digital system)
42 DVSS - Ground terminal (digital system)
43 REG1_EXTR (OPN) O Internal regulator reserve terminal Not used
44 DVDD15 O External capacitor connection terminal for internal regulator
45 TXD1 O UART data output to the system controller
46 RXD1 I UART data input from the system controller
47 SMONI O Watch-dog timer status monitor output to the system controller
48 OPCDM I External decode permission signal input from the digital servo processor
49 DVDD - Power supply terminal (+3.3V) (digital system)
50 DVSS - Ground terminal (digital system)
51 RESETB I Reset signal input from the system controller “L”: reset
52 SIFCK I Serial data transfer clock signal input from the system controller
53 SIFDI I Serial data input from the system controller
54 SIFDO O Serial data output to the system controller
55 SIFCE I Chip enable signal input from the system controller
56 BUSYB O Busy signal output to the system controller “L”: busy
57 CD_BUSYB I Busy signal input from the digital servo processor “L”: busy
58 LRCK I L/R sampling clock signal input from the digital servo processor
59 BCK I Bit clock signal input from the digital servo processor
60 DATA I Audio data input from the digital servo processor
61 MCLK I Master clock signal input from the digital servo processor
62 USB_IN O USB device detection signal output to the system controller “L”: USB device is connected
GP45 (NCO) to
63 to 65 I/O Not used
GP47 (NCO)

27
CDX-G3100UE/G3100UV/G3150UP/G3150UV

Pin No. Pin Name I/O Description

66 DVSS - Ground terminal (digital system)
67 DVDD - Power supply terminal (+3.3V) (digital system)
68 UDM1 I/O Two-way USB data (–) bus with the USB connector
69 UDP1 I/O Two-way USB data (+) bus with the USB connector
70 DVSS - Ground terminal (for digital system)
71 UDM2 I/O Two-way USB data (–) bus terminal Not used
72 UDP2 I/O Two-way USB data (+) bus terminal Not used
73 XVDD - Power supply terminal (+3.3V) (for oscillation circuit)
74 X12IN I System clock input terminal (12 MHz)
75 X12OUT O System clock output terminal (12 MHz)
76 XVSS - Ground terminal (for oscillation circuit)
77 AFILT O Charge pump output terminal for PLL
78, 79 VVDD2, VVDD3 - Power supply terminal (+3.3V) (for PLL)
80 DVSS - Ground terminal (digital system)
81 DVDD - Power supply terminal (+3.3V) (digital system)
82 CP_SCL O Serial data transfer clock signal output to the EEPROM
83 CP_SDA I/O Two-way data bus with the EEPROM
84 CP_RESET O Reset signal output terminal Not used
85 CD_RESB O Reset signal output to the digital servo processor “L”: reset
86 CMD_ERR O Command error signal output to the system controller “H”: error
87 TEST0 (GND) I Test mode setting terminal Fixed at “L”
88 DVDD - Power supply terminal (+3.3V) (digital system)
89 DVSS - Ground terminal (for digital system)
90 DVDD15 O External capacitor connection terminal for internal regulator
91 JTRSTB (IPD) I Reset signal input terminal (for JTAG) Normally: fixed at “L”
92 JTCK (IPD) I Clock signal input terminal (for JTAG) Normally: fixed at “L”
93 JTDI (IPD) I Data input terminal (for JTAG) Normally: fixed at “L”
94 JTMS (IPU) I Mode selection signal input terminal (for JTAG) Normally: fixed at “H”
95 JTDO (O) O Data output terminal (for JTAG) Normally: open
96 JTRTCK (O) O Return clock signal output terminal (for JTAG) Normally: open
97 TEST1 (GND) I Test mode setting terminal Fixed at “L”
98 AVDD1 - Power supply terminal (+3.3V) (analog system)
99 AVSS1 - Ground terminal (analog system)
External capacitor connection terminal for audio D/A converter and electrical volume reference
100 LRREF O
voltage

28
 CDX-G3100UE/G3100UV/G3150UP/G3150UV

MAIN BOARD IC701 LC78615E-01US-H (RF AMP, DIGITAL SERVO PROCESSOR)

Pin No. Pin Name I/O Description
1 EFMIN I RF signal input terminal
2 RFOUT O RF signal output terminal
3 LPF - External low-pass filter capacitor connection terminal for DC level detection of RF signal
4 PHLPF - External low-pass filter capacitor connection terminal for scratch detection
5 AIN I Main beam (B) input from the CD mechanism deck block
6 CIN I Main beam (C) input from the CD mechanism deck block
7 BIN I Main beam (A) input from the CD mechanism deck block
8 DIN I Main beam (C) input from the CD mechanism deck block
9 SLCISET - External resistor connection terminal for current setting of SLCO output
10 RFMON - Internal analog signal monitor terminal of LSI Not used
11 VREF O Reference voltage (+1.65V) output terminal for RF
12 JITTC - External capacitor connection terminal for jitter detection
13 EIN I Sub beam (F) input from the CD mechanism deck block
14 FIN I Sub beam (E) input from the CD mechanism deck block
15 TE O Tracking error signal output terminal
16 TEIN I Tracking error signal input terminal
17 AVSS - Ground terminal (analog system)
18 AVDD - Power supply terminal (+3.3V) (analog system)
19 LDD O Laser power control signal output to the CD mechanism deck block
20 LDS I Laser power detection signal input from the CD mechanism deck block
21 FDO O Focus coil control signal output to the CD mechanism deck block
22 TDO O Tracking coil control signal output to the CD mechanism deck block
23 SLDO O Sled motor control signal output to the CD mechanism deck block
24 SPDO O Spindle motor control signal output to the CD mechanism deck block
25 VVSS1 - Ground terminal (for EFMPLL)
26, 27 PDOUT1, PDOUT0 O Charge pump output terminal for EFMPLL
28 PCKIST - External resistor connection terminal for charge pump current setting for EFMPLL
29 VVDD1 - Power supply terminal (+3.3V) (for EFMPLL)
30, 31 NC - Not used
32 DVDD15 - External power capacitor connection terminal for digital system power
33 DVDD - Power supply terminal (+3.3V) (digital system)
34 DVSS - Ground terminal (digital system)
35 TEST I Test mode setting terminal Fixed at “L”
36 L_SW I Limit in detection switch input terminal
37, 38 NC - Not used
39 OPCDM O External decode permission signal output to the audio DSP
40 SBSY O CD sub-code block sync signal output to the audio DSP
41 SFSY O CD sub-code flame sync signal output to the audio DSP
42 PW O CD sub-code PW data output to the audio DSP
43 SBCK O CD sub-code data transfer clock signal output to the audio DSP
44 CE I Chip enable signal input from the audio DSP
45 CL I Serial data transfer clock signal input from the audio DSP
46 DI I Serial data input from the audio DSP
47 DO O Serial data output to the audio DSP
48 RESB I Reset signal input from the audio DSP “L”: reset
49 BUSYB O Busy signal output to the audio DSP “L”: busy
50 MCLK O Master clock signal output to the audio DSP
51 LRCK O L/R sampling clock signal output to the audio DSP
52 BCK O Bit clock signal output to the audio DSP
53 DATA O Audio data output to the audio DSP
54 to 56 SMOIN0 to SMOIN2 O Servo internal signal monitor output terminal Not used
57 MODE I LSI operation mode setting terminal Fixed at “H”
58 DVDD15 - External power capacitor connection terminal for digital system power
59 DVDD - Power supply terminal (+3.3V) (digital system)
60 XVSS - Ground terminal (for oscillation circuit)
61 XOUT O System clock output terminal (16.934 MHz)
62 XIN I System clock input terminal (16.934 MHz)
63 XVDD - Power supply terminal (+3.3V) (for oscillation circuit)
64 SLCO O Slice level control signal output terminal

29
CDX-G3100UE/G3100UV/G3150UP/G3150UV
Ver. 1.1 SECTION 5
EXPLODED VIEWS
Note:
• -XX and -X mean standardized parts, so • The mechanical parts with no reference
they may have some difference from the number in the exploded views are not sup-
original one. plied.
• Items marked “*” are not stocked since • Color Indication of Appearance Parts Ex-
they are seldom required for routine ser- ample:
vice. Some delay should be anticipated KNOB, BALANCE (WHITE) . . . (RED)
when ordering these items.  
Parts Color Cabinet’s Color

5-1. SUB PANEL SECTION

Note: The service manual of the mechanism deck, used in this model has
been issued in a separate volume. Please refer to the service manual
of the MG-101 series for the mechanism deck information.

not supplied

C
B
#2
not supplied
CD mechanism deck section
(MG-101CF-188)
#2

(G3100UE/G3100UV) (G3150UP/G3150UV) A
FU1

#1 PW1

FFC1
B
2
not supplied
(for FRONT PANEL) 3
A
C #1

1
#1
#1 chassis section

FP1

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 X-2587-755-1 KNOB (VOL) (SV) ASSY FP1 A-2058-348-A PANEL OVERALL ASSY, FRONT (G3150UV: EA)
2 X-2187-544-5 CASE ASSY (G3150UP/G3150UV)
3 X-2589-833-1 PANEL ASSY, SUB FP1 A-2058-349-A PANEL OVERALL ASSY, FRONT (G3150UV: IND)
FFC1 1-846-819-41 CABLE FLEXIBLE FLAT (27 CORE) FU1 1-523-227-11 MINI FUSE (BLADE TYPE) (10 A/32 V)
(Length: 80 mm) PW1 1-846-032-11 CONNECTION CABLE (ISO) (POWER CORD)
FP1 A-2058-343-A PANEL OVERALL ASSY, FRONT (G3100UV) (G3100UE/G3100UV)
PW1 1-846-978-11 CONNECTION CABLE, AUTOMOBILE
FP1 A-2058-344-A PANEL OVERALL ASSY, FRONT (G3100UE) (POWER CORD) (G3150UP/G3150UV)
FP1 A-2058-345-A PANEL OVERALL ASSY, FRONT (G3150UV: E) #1 7-685-792-09 SCREW +PTT 2.6X6 (S)
FP1 A-2058-346-A PANEL OVERALL ASSY, FRONT (G3150UP)
FP1 A-2058-347-A PANEL OVERALL ASSY, FRONT (G3150UV: MX) #2 7-685-790-01 SCREW +PTT 2.6X4 (S)

30
 CDX-G3100UE/G3100UV/G3150UP/G3150UV

5-2. CHASSIS SECTION

#3

51
#5

not supplied #4
#4
#4 #5

#4
#3

MAIN board D

52
52
TU01

(EA)

53

not supplied

not supplied

Note: When the complete MAIN board is replaced, the destination setting is necessary. Refer to “NOTE OF
REPLACING THE COMPLETE MAIN BOARD OR SYSTEM CONTROLLER (IC501)” on page 4.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
51 A-2058-097-A MAIN BOARD, COMPLETE (See Note) #3 7-685-793-01 SCREW +PTT 2.6X8 (S)
52 4-410-504-01 SCREW (+PTT 2.6X6), GROUND POINT
53 4-547-980-01 SHEET HEAT TRANSFER (EA) #4 7-685-794-01 SCREW +PTT 2.6X10 (S)
TU01 A-2057-353-A TUX-DSP04 (TUNER UNIT) #5 7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT

31
CDX-G3100UE/G3100UV/G3150UP/G3150UV
SECTION 6
KEY MAIN
ELECTRICAL PARTS LIST
Note:
• Due to standardization, replacements in • CAPACITORS When indicating parts by reference num-
the parts list may be different from the uF: μF ber, please include the board name.
parts specified in the diagrams or the com- • COILS
ponents used on the set. uH: μH
• -XX and -X mean standardized parts, so • SEMICONDUCTORS
they may have some difference from the In each case, u: μ, for example:
original one. uA. . : μA. . , uPA. . , μPA. . ,
• Items marked “*” are not stocked since uPB. . : μPB. . , uPC. . , μPC. . ,
they are seldom required for routine ser- uPD. . : μPD. .
vice. Some delay should be anticipated
when ordering these items.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
KEY BOARD * C312 1-116-735-11 CERAMIC CHIP 1uF 10% 16V
********** * C313 1-116-735-11 CERAMIC CHIP 1uF 10% 16V

When the KEY board is defective, replace the FRONT PANEL OVERALL ASSY * C314 1-116-735-11 CERAMIC CHIP 1uF 10% 16V
(Ref. No. FP1). * C315 1-116-735-11 CERAMIC CHIP 1uF 10% 16V
************************************************************* * C316 1-116-735-11 CERAMIC CHIP 1uF 10% 16V
* C317 1-116-735-11 CERAMIC CHIP 1uF 10% 16V
A-2058-097-A MAIN BOARD, COMPLETE (See Note) C319 1-164-866-11 CERAMIC CHIP 47PF 5% 50V
********************
C320 1-164-866-11 CERAMIC CHIP 47PF 5% 50V
7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT C321 1-116-733-11 CERAMIC CHIP 1uF 10% 25V
7-685-794-01 SCREW +PTT 2.6X10 (S) C322 1-164-866-11 CERAMIC CHIP 47PF 5% 50V
C323 1-164-866-11 CERAMIC CHIP 47PF 5% 50V
< CAPACITOR > C324 1-116-733-11 CERAMIC CHIP 1uF 10% 25V

C13 1-118-361-11 CERAMIC CHIP 0.1uF 10% 50V C325 1-118-361-11 CERAMIC CHIP 0.1uF 10% 50V
C100 1-118-290-11 CERAMIC CHIP 0.001uF 10% 50V C326 1-116-733-11 CERAMIC CHIP 1uF 10% 25V
C101 1-118-290-11 CERAMIC CHIP 0.001uF 10% 50V C350 1-118-997-11 ELECT 3300uF 20% 16V
C102 1-116-992-21 CERAMIC CHIP 2.2uF 10% 50V C400 1-116-734-11 CERAMIC CHIP 1uF 20% 16V
C105 1-116-716-11 CERAMIC CHIP 10uF 10% 16V C401 1-164-882-11 CERAMIC CHIP 220PF 5% 16V

C115 1-116-733-11 CERAMIC CHIP 1uF 10% 25V C402 1-116-722-11 CERAMIC CHIP 4.7uF 10% 16V
C200 1-116-865-11 CERAMIC CHIP 10uF 10% 25V C404 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C201 1-116-865-11 CERAMIC CHIP 10uF 10% 25V C405 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V
C202 1-116-865-11 CERAMIC CHIP 10uF 10% 25V C406 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C204 1-116-742-11 CERAMIC CHIP 0.22uF 10% 25V C407 1-116-722-11 CERAMIC CHIP 4.7uF 10% 16V

C206 1-116-742-11 CERAMIC CHIP 0.22uF 10% 25V C409 1-164-882-11 CERAMIC CHIP 220PF 5% 16V
C207 1-116-733-11 CERAMIC CHIP 1uF 10% 25V C410 1-116-734-11 CERAMIC CHIP 1uF 20% 16V
C208 1-100-966-91 CERAMIC CHIP 10uF 20% 10V C411 1-118-040-11 CERAMIC CHIP 2.2uF 10% 16V
C209 1-100-966-91 CERAMIC CHIP 10uF 20% 10V C412 1-118-040-11 CERAMIC CHIP 2.2uF 10% 16V
C210 1-100-767-21 ELECT CHIP 220uF 20% 16V C415 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V

C211 1-117-681-11 ELECT CHIP 100uF 20% 16V C416 1-100-966-91 CERAMIC CHIP 10uF 20% 10V
C212 1-118-403-11 CERAMIC CHIP 0.001uF 10% 50V C418 1-118-047-11 CERAMIC CHIP 10uF 10% 16V
C213 1-118-403-11 CERAMIC CHIP 0.001uF 10% 50V C420 1-164-882-11 CERAMIC CHIP 220PF 5% 16V
C251 1-100-767-21 ELECT CHIP 220uF 20% 16V C421 1-116-734-11 CERAMIC CHIP 1uF 20% 16V
C253 1-127-931-21 ELECT CHIP 470uF 20% 16V C422 1-118-047-11 CERAMIC CHIP 10uF 10% 16V

C260 1-117-681-11 ELECT CHIP 100uF 20% 16V C423 1-100-966-91 CERAMIC CHIP 10uF 20% 10V
C300 1-118-361-11 CERAMIC CHIP 0.1uF 10% 50V C450 1-128-992-21 ELECT CHIP 47uF 20% 25V
C301 1-116-078-11 CERAMIC CHIP 1uF 10% 50V C501 1-118-403-11 CERAMIC CHIP 0.001uF 10% 50V
C302 1-164-866-11 CERAMIC CHIP 47PF 5% 50V C502 1-118-403-11 CERAMIC CHIP 0.001uF 10% 50V
C303 1-164-866-11 CERAMIC CHIP 47PF 5% 50V C520 1-118-403-11 CERAMIC CHIP 0.001uF 10% 50V

C304 1-164-866-11 CERAMIC CHIP 47PF 5% 50V C521 1-118-459-11 CERAMIC CHIP 0.01uF 10% 25V
C305 1-116-733-11 CERAMIC CHIP 1uF 10% 25V C522 1-118-459-11 CERAMIC CHIP 0.01uF 10% 25V
C306 1-164-866-11 CERAMIC CHIP 47PF 5% 50V C523 1-118-459-11 CERAMIC CHIP 0.01uF 10% 25V
C307 1-100-966-91 CERAMIC CHIP 10uF 20% 10V C524 1-164-856-81 CERAMIC CHIP 18PF 5% 50V
* C308 1-116-735-11 CERAMIC CHIP 1uF 10% 16V C526 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V

* C309 1-116-735-11 CERAMIC CHIP 1uF 10% 16V C527 1-112-733-81 CERAMIC CHIP 20PF 5% 50V
* C310 1-116-735-11 CERAMIC CHIP 1uF 10% 16V C528 1-164-842-11 CERAMIC CHIP 2PF 0.25PF 50V
* C311 1-116-735-11 CERAMIC CHIP 1uF 10% 16V C530 1-164-842-11 CERAMIC CHIP 2PF 0.25PF 50V
Note: When the complete MAIN board is replaced, the destination setting is necessary. Refer to “NOTE OF
REPLACING THE COMPLETE MAIN BOARD OR SYSTEM CONTROLLER (IC501)” on page 4.

32
 CDX-G3100UE/G3100UV/G3150UP/G3150UV
MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C531 1-118-459-11 CERAMIC CHIP 0.01uF 10% 25V C724 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V
C532 1-118-459-11 CERAMIC CHIP 0.01uF 10% 25V C725 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V

C533 1-118-459-11 CERAMIC CHIP 0.01uF 10% 25V C726 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V
C534 1-164-866-11 CERAMIC CHIP 47PF 5% 50V C727 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V
C535 1-164-866-11 CERAMIC CHIP 47PF 5% 50V C728 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V
C550 1-114-612-21 ELECT CHIP 220uF 20% 6.3V C729 1-116-744-11 CERAMIC CHIP 0.22uF 10% 10V
C551 1-118-040-11 CERAMIC CHIP 2.2uF 10% 16V C730 1-118-389-11 CERAMIC CHIP 0.022uF 10% 25V

C600 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V C734 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V
C601 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V C750 1-117-681-11 ELECT CHIP 100uF 20% 16V
C602 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V C752 1-100-363-11 ELECT CHIP 220uF 20% 4V
C603 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V C753 1-126-209-11 ELECT CHIP 100uF 20% 4V
C604 1-116-350-21 CERAMIC CHIP 47uF 20% 4V C1300 1-100-671-11 CERAMIC CHIP 4.7uF 20% 25V

C609 1-116-732-11 CERAMIC CHIP 2.2uF 20% 6.3V C1301 1-116-733-11 CERAMIC CHIP 1uF 10% 25V
C613 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V C1305 1-100-055-21 CERAMIC CHIP 22uF 20% 16V
C614 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C1306 1-118-391-11 CERAMIC CHIP 0.01uF 10% 50V
C615 1-116-729-11 CERAMIC CHIP 2.2uF 20% 10V C1307 1-100-906-11 CERAMIC CHIP 0.01uF 10% 16V
C616 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C1309 1-116-733-11 CERAMIC CHIP 1uF 10% 25V

C617 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C1316 1-100-966-91 CERAMIC CHIP 10uF 20% 10V
C618 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C1317 1-100-966-91 CERAMIC CHIP 10uF 20% 10V
C619 1-164-845-11 CERAMIC CHIP 5PF 0.25PF 50V C1321 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C620 1-164-845-11 CERAMIC CHIP 5PF 0.25PF 50V C1323 1-118-040-11 CERAMIC CHIP 2.2uF 10% 16V
C624 1-164-852-11 CERAMIC CHIP 12PF 5% 50V C1326 1-162-923-11 CERAMIC CHIP 47PF 5% 50V

* C625 1-116-720-11 CERAMIC CHIP 10uF 20% 6.3V C1350 1-137-765-21 ELECT CHIP 47uF 20% 16V
* C626 1-116-720-11 CERAMIC CHIP 10uF 20% 6.3V C1353 1-117-681-11 ELECT CHIP 100uF 20% 16V
C627 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V C1354 1-116-737-11 CERAMIC CHIP 1uF 20% 10V
C628 1-164-852-11 CERAMIC CHIP 12PF 5% 50V C1359 1-118-403-11 CERAMIC CHIP 0.001uF 10% 50V
C629 1-118-397-11 CERAMIC CHIP 0.0033uF 10% 50V C1360 1-118-389-11 CERAMIC CHIP 0.022uF 10% 25V

C630 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V C1361 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V
C631 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V C1362 1-118-403-11 CERAMIC CHIP 0.001uF 10% 50V
C632 1-116-350-21 CERAMIC CHIP 47uF 20% 4V C1368 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V
C633 1-164-882-11 CERAMIC CHIP 220PF 5% 16V C1369 1-164-874-11 CERAMIC CHIP 100PF 5% 50V
C634 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V C1370 1-118-290-11 CERAMIC CHIP 0.001uF 10% 50V

C636 1-118-388-11 CERAMIC CHIP 0.047uF 10% 25V C1371 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C637 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C1374 1-118-347-11 CERAMIC CHIP 0.1uF 10% 25V
C639 1-116-734-11 CERAMIC CHIP 1uF 20% 16V C1376 1-164-866-11 CERAMIC CHIP 47PF 5% 50V
C640 1-116-734-11 CERAMIC CHIP 1uF 20% 16V C1377 1-116-737-11 CERAMIC CHIP 1uF 20% 10V
C641 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V C1378 1-100-767-21 ELECT CHIP 220uF 20% 16V

C650 1-165-492-21 ELECT CHIP 100uF 20% 10V C1379 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V
C651 1-114-612-21 ELECT CHIP 220uF 20% 6.3V C1380 1-118-040-11 CERAMIC CHIP 2.2uF 10% 16V
C652 1-165-708-11 ELECT CHIP 47uF 20% 6.3V C1381 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V
C653 1-117-681-11 ELECT CHIP 100uF 20% 16V C1386 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C700 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V
< CONNECTOR >
C701 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V
C702 1-118-347-11 CERAMIC CHIP 0.1uF 10% 25V CN101 1-842-266-22 SOCKET, CONNECTOR 20P
C703 1-164-854-11 CERAMIC CHIP 15PF 5% 50V CN301 1-843-330-21 PIN, CONNECTOR 16P
C705 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V CN704 1-843-775-11 CONNECTOR, FFC/FPC (ZIF) 27P
C706 1-118-403-11 CERAMIC CHIP 0.001uF 10% 50V
< DIODE >
C710 1-118-459-11 CERAMIC CHIP 0.01uF 10% 25V
C711 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V D109 1-805-043-12 ABSORBER, CHIP SURGE
C712 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V D110 1-805-043-12 ABSORBER, CHIP SURGE
C713 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V D152 6-502-969-01 DIODE DZ2J06800L
C714 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V D200 6-503-238-01 DIODE GN1G
D300 6-503-238-01 DIODE GN1G
C715 1-118-459-11 CERAMIC CHIP 0.01uF 10% 25V
C717 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V D301 6-503-238-01 DIODE GN1G
C718 1-118-290-11 CERAMIC CHIP 0.001uF 10% 50V D302 6-503-238-01 DIODE GN1G
C719 1-118-395-11 CERAMIC CHIP 0.0047uF 10% 50V D303 6-503-238-01 DIODE GN1G
C720 1-118-388-11 CERAMIC CHIP 0.047uF 10% 25V D305 6-503-238-01 DIODE GN1G
D350 6-503-016-01 DIODE DZ2J07500L
C721 1-118-459-11 CERAMIC CHIP 0.01uF 10% 25V
C722 1-118-347-11 CERAMIC CHIP 0.1uF 10% 25V D351 6-503-031-01 DIODE DZ2J18000L
C723 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V D353 6-503-031-01 DIODE DZ2J18000L

33
CDX-G3100UE/G3100UV/G3150UP/G3150UV
MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
D400 6-502-961-01 DIODE DA2J10100L Q700 8-729-026-49 TRANSISTOR 2SA1037AK-T146-R
D500 6-502-131-01 DIODE LRB751V-40T1G
* D503 6-503-578-01 DIODE RB520SM-30T2R < RESISTOR >

D1301 6-503-548-01 DIODE DB2441600L R11 1-218-990-81 SHORT CHIP 0

D1302 6-502-961-01 DIODE DA2J10100L R14 1-216-864-11 SHORT CHIP 0
R15 1-216-864-11 SHORT CHIP 0
< FERRITE BEAD > R19 1-216-864-11 SHORT CHIP 0
R102 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
FB100 1-400-334-21 FERRITE, EMI (SMD) (1608)
FB104 1-400-334-21 FERRITE, EMI (SMD) (1608) R103 1-216-835-11 METAL CHIP 15K 5% 1/10W
FB105 1-400-334-21 FERRITE, EMI (SMD) (1608) R104 1-216-065-91 METAL CHIP 4.7K 5% 1/10W
FB800 1-500-113-22 BEAD, FERRITE (CHIP) (1608) R105 1-216-065-91 METAL CHIP 4.7K 5% 1/10W
FB801 1-500-113-22 BEAD, FERRITE (CHIP) (1608) R106 1-216-835-11 METAL CHIP 15K 5% 1/10W
R107 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
FB802 1-500-113-22 BEAD, FERRITE (CHIP) (1608)
FB803 1-481-643-21 FERRITE, EMI (SMD) R203 1-216-864-11 SHORT CHIP 0
FB804 1-481-396-21 FERRITE, EMI (SMD) (1608) R210 1-220-199-81 METAL CHIP 24K 5% 1/16W
FB805 1-469-084-21 INDUCTOR, FERRITE BEAD (1005) R211 1-218-960-11 METAL CHIP 3.9K 5% 1/16W
FB806 1-500-113-22 BEAD, FERRITE (CHIP) (1608) R212 1-218-971-81 METAL CHIP 33K 5% 1/16W
R213 1-218-965-11 METAL CHIP 10K 5% 1/16W
FB807 1-500-113-22 BEAD, FERRITE (CHIP) (1608)
FB808 1-500-113-22 BEAD, FERRITE (CHIP) (1608) R214 1-218-953-11 METAL CHIP 1K 5% 1/16W
FB810 1-481-746-11 SDM EMI FERRITE R300 1-218-981-81 METAL CHIP 220K 5% 1/16W
FB811 1-481-643-21 FERRITE, EMI (SMD) R301 1-218-953-11 METAL CHIP 1K 5% 1/16W
R302 1-218-953-11 METAL CHIP 1K 5% 1/16W
< IC > R308 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

IC201 6-720-775-01 IC LV56841PVD-XH R309 1-216-841-11 METAL CHIP 47K 5% 1/10W

IC300 6-720-774-01 IC PURE5001H-4WX R310 1-216-073-91 METAL CHIP 10K 5% 1/10W
IC401 6-721-638-01 IC NJM8065RB1-TE1 R311 1-216-841-11 METAL CHIP 47K 5% 1/10W
IC402 6-721-638-01 IC NJM8065RB1-TE1 R312 1-216-073-91 METAL CHIP 10K 5% 1/10W
IC403 6-721-638-01 IC NJM8065RB1-TE1 R313 1-218-965-11 METAL CHIP 10K 5% 1/16W

IC501 6-721-869-01 IC LC88FC2H0AF2314-2H (SV) (See Note 1) R314 1-218-973-11 METAL CHIP 47K 5% 1/16W
IC601 6-721-637-01 IC LC786800E-6C07-H R315 1-218-943-11 METAL CHIP 150 5% 1/16W
IC602 6-718-324-01 IC MFI337S3959 R316 1-218-973-11 METAL CHIP 47K 5% 1/16W
IC701 6-720-790-01 IC LC78615E-01US-H R361 1-216-813-11 METAL CHIP 220 5% 1/10W
IC1301 (Not supplied) IC BD9876AEFJ-BZE2 (See Note 2) R362 1-216-813-11 METAL CHIP 220 5% 1/10W

IC1304 6-720-899-01 IC BD2242G-GTR R363 1-216-813-11 METAL CHIP 220 5% 1/10W

R364 1-216-813-11 METAL CHIP 220 5% 1/10W
< JACK > R400 1-216-801-11 METAL CHIP 22 5% 1/10W
R401 1-218-965-11 METAL CHIP 10K 5% 1/16W
J01 1-843-791-11 JACK (ANT) (ANTENNA IN) R402 1-218-941-81 METAL CHIP 100 5% 1/16W
J401 1-822-712-31 JACK, PIN 4P (AUDIO OUT REAR/SUB)
J801 1-566-822-81 JACK (REMOTE IN) R403 1-218-977-11 METAL CHIP 100K 5% 1/16W
R404 1-218-951-11 METAL CHIP 680 5% 1/16W
< COIL > R406 1-218-966-11 METAL CHIP 12K 5% 1/16W
R407 1-218-965-11 METAL CHIP 10K 5% 1/16W
L10 1-400-073-21 INDUCTOR 4.7uH R408 1-218-965-11 METAL CHIP 10K 5% 1/16W
L105 1-469-844-11 INDUCTOR 2.2uH
L300 1-460-443-11 CHOKE COIL 140uH R411 1-218-951-11 METAL CHIP 680 5% 1/16W
L1301 1-481-904-11 INDUCTOR 47uH R412 1-218-966-11 METAL CHIP 12K 5% 1/16W
R413 1-218-941-81 METAL CHIP 100 5% 1/16W
< TRANSISTOR > R414 1-218-965-11 METAL CHIP 10K 5% 1/16W
R415 1-218-977-11 METAL CHIP 100K 5% 1/16W
Q300 6-552-949-01 TRANSISTOR LTC044EUBFS8TL
Q301 6-552-936-01 TRANSISTOR LTC014EUBFS8TL R416 1-218-965-11 METAL CHIP 10K 5% 1/16W
Q302 6-552-892-01 TRANSISTOR LSCR523UBFS8TL R417 1-218-963-11 METAL CHIP 6.8K 5% 1/16W
Q304 6-552-892-01 TRANSISTOR LSCR523UBFS8TL R418 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W
Q405 6-552-937-01 TRANSISTOR LTC014TUBFS8TL R419 1-218-977-11 METAL CHIP 100K 5% 1/16W
R421 1-218-977-11 METAL CHIP 100K 5% 1/16W
Q406 6-552-937-01 TRANSISTOR LTC014TUBFS8TL
Q407 6-552-922-01 TRANSISTOR LTA014EUBFS8TL R422 1-218-953-11 METAL CHIP 1K 5% 1/16W
Q408 6-552-922-01 TRANSISTOR LTA014EUBFS8TL R423 1-218-977-11 METAL CHIP 100K 5% 1/16W
Q409 6-552-936-01 TRANSISTOR LTC014EUBFS8TL R424 1-218-974-11 METAL CHIP 56K 5% 1/16W
Q410 6-552-937-01 TRANSISTOR LTC014TUBFS8TL R425 1-218-968-11 METAL CHIP 18K 5% 1/16W
R426 1-218-941-81 METAL CHIP 100 5% 1/16W
Q411 6-552-937-01 TRANSISTOR LTC014TUBFS8TL
Q412 6-552-937-01 TRANSISTOR LTC014TUBFS8TL R427 1-216-797-11 METAL CHIP 10 5% 1/10W
Q413 6-552-937-01 TRANSISTOR LTC014TUBFS8TL R428 1-218-959-11 METAL CHIP 3.3K 5% 1/16W
Note 1: When IC501 on the MAIN board is replaced, the destination setting Note 2: IC1301 on the MAIN board cannot replace
is necessary. Refer to “NOTE OF REPLACING THE COMPLETE with single. When this part is damaged, replace
MAIN BOARD OR SYSTEM CONTROLLER (IC501)” on page 4. the complete mounted board.

34
 CDX-G3100UE/G3100UV/G3150UP/G3150UV
Ver. 1.1
MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R429 1-218-977-11 METAL CHIP 100K 5% 1/16W R600 1-216-864-11 SHORT CHIP 0
R431 1-218-968-11 METAL CHIP 18K 5% 1/16W R603 1-218-949-11 METAL CHIP 470 5% 1/16W
R432 1-218-965-11 METAL CHIP 10K 5% 1/16W R604 1-218-990-81 SHORT CHIP 0

R433 1-218-966-11 METAL CHIP 12K 5% 1/16W R608 1-216-799-11 METAL CHIP 15 5% 1/10W
R434 1-218-929-11 METAL CHIP 10 5% 1/16W R609 1-216-799-11 METAL CHIP 15 5% 1/10W
R500 1-218-977-11 METAL CHIP 100K 5% 1/16W R610 1-218-967-11 METAL CHIP 15K 5% 1/16W
R502 1-218-977-11 METAL CHIP 100K 5% 1/16W R611 1-218-967-11 METAL CHIP 15K 5% 1/16W
R503 1-218-977-11 METAL CHIP 100K 5% 1/16W R612 1-218-967-11 METAL CHIP 15K 5% 1/16W

R505 1-218-977-11 METAL CHIP 100K 5% 1/16W R613 1-218-967-11 METAL CHIP 15K 5% 1/16W
R506 1-218-953-11 METAL CHIP 1K 5% 1/16W R614 1-218-989-11 METAL CHIP 1M 5% 1/16W
R511 1-218-977-11 METAL CHIP 100K 5% 1/16W R615 1-218-959-11 METAL CHIP 3.3K 5% 1/16W
R512 1-218-977-11 METAL CHIP 100K 5% 1/16W R616 1-218-961-11 METAL CHIP 4.7K 5% 1/16W
R514 1-218-977-11 METAL CHIP 100K 5% 1/16W R620 1-218-973-11 METAL CHIP 47K 5% 1/16W

R517 1-218-977-11 METAL CHIP 100K 5% 1/16W R621 1-218-973-11 METAL CHIP 47K 5% 1/16W
R519 1-250-519-11 METAL CHIP 10K 1% 1/16W R622 1-218-973-11 METAL CHIP 47K 5% 1/16W
R520 1-250-519-11 METAL CHIP 10K 1% 1/16W R623 1-218-973-11 METAL CHIP 47K 5% 1/16W
R521 1-218-977-11 METAL CHIP 100K 5% 1/16W R624 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R522 1-218-977-11 METAL CHIP 100K 5% 1/16W R625 1-218-957-11 METAL CHIP 2.2K 5% 1/16W

R523 1-250-519-11 METAL CHIP 10K 1% 1/16W R700 1-218-959-11 METAL CHIP 3.3K 5% 1/16W
R524 1-220-200-81 METAL CHIP 30K 5% 1/16W R701 1-218-959-11 METAL CHIP 3.3K 5% 1/16W
R525 1-218-953-11 METAL CHIP 1K 5% 1/16W R702 1-218-965-11 METAL CHIP 10K 5% 1/16W
R526 1-218-949-11 METAL CHIP 470 5% 1/16W R703 1-218-949-11 METAL CHIP 470 5% 1/16W
R527 1-218-953-11 METAL CHIP 1K 5% 1/16W R704 1-218-975-11 METAL CHIP 68K 5% 1/16W

R528 1-218-941-81 METAL CHIP 100 5% 1/16W R705 1-242-967-11 METAL CHIP 1 5% 1/16W
R529 1-218-941-81 METAL CHIP 100 5% 1/16W R707 1-216-864-11 SHORT CHIP 0
R530 1-218-941-81 METAL CHIP 100 5% 1/16W R710 1-218-947-11 METAL CHIP 330 5% 1/16W
R531 1-218-941-81 METAL CHIP 100 5% 1/16W R714 1-218-949-11 METAL CHIP 470 5% 1/16W
R532 1-218-941-81 METAL CHIP 100 5% 1/16W R715 1-218-975-11 METAL CHIP 68K 5% 1/16W

R533 1-218-971-81 METAL CHIP 33K 5% 1/16W R716 1-218-951-11 METAL CHIP 680 5% 1/16W
R535 1-218-953-11 METAL CHIP 1K 5% 1/16W R717 1-218-951-11 METAL CHIP 680 5% 1/16W
R536 1-218-971-81 METAL CHIP 33K 5% 1/16W R720 1-218-971-81 METAL CHIP 33K 5% 1/16W
R537 1-218-953-11 METAL CHIP 1K 5% 1/16W R729 1-218-975-11 METAL CHIP 68K 5% 1/16W
R539 1-218-971-81 METAL CHIP 33K 5% 1/16W R732 1-216-864-11 SHORT CHIP 0

R540 1-245-604-11 METAL CHIP 10M 5% 1/16W R735 1-220-802-11 METAL CHIP 3.3 5% 1/16W
R542 1-218-981-81 METAL CHIP 220K 5% 1/16W R1303 1-218-961-11 METAL CHIP 4.7K 5% 1/16W
R543 1-218-977-11 METAL CHIP 100K 5% 1/16W R1308 1-208-927-11 METAL CHIP 47K 0.5% 1/16W
R544 1-218-989-11 METAL CHIP 1M 5% 1/16W R1309 1-208-695-11 METAL CHIP 3.3K 0.5% 1/16W
R545 1-218-990-81 SHORT CHIP 0 R1310 1-208-709-11 METAL CHIP 12K 0.5% 1/16W

R546 1-218-977-11 METAL CHIP 100K 5% 1/16W R1311 1-218-953-11 METAL CHIP 1K 5% 1/16W
R548 1-218-977-11 METAL CHIP 100K 5% 1/16W R1312 1-218-953-11 METAL CHIP 1K 5% 1/16W
R549 1-218-965-11 METAL CHIP 10K 5% 1/16W R1323 1-220-203-11 METAL CHIP 51K 5% 1/16W
R551 1-218-977-11 METAL CHIP 100K 5% 1/16W R1324 1-218-969-11 METAL CHIP 22K 5% 1/16W
R554 1-218-977-11 METAL CHIP 100K 5% 1/16W R1326 1-218-965-11 METAL CHIP 10K 5% 1/16W

R556 1-218-977-11 METAL CHIP 100K 5% 1/16W R1331 1-218-941-81 METAL CHIP 100 5% 1/16W
R560 1-218-977-11 METAL CHIP 100K 5% 1/16W R1332 1-218-941-81 METAL CHIP 100 5% 1/16W
R561 1-218-977-11 METAL CHIP 100K 5% 1/16W R1333 1-216-864-11 SHORT CHIP 0
R563 1-218-977-11 METAL CHIP 100K 5% 1/16W R1334 1-218-990-81 SHORT CHIP 0
R565 1-218-975-11 METAL CHIP 68K 5% 1/16W R1335 1-218-941-81 METAL CHIP 100 5% 1/16W

R568 1-218-941-81 METAL CHIP 100 5% 1/16W R1336 1-218-941-81 METAL CHIP 100 5% 1/16W
R569 1-218-941-81 METAL CHIP 100 5% 1/16W R1337 1-218-941-81 METAL CHIP 100 5% 1/16W
R570 1-218-965-11 METAL CHIP 10K 5% 1/16W R1338 1-218-941-81 METAL CHIP 100 5% 1/16W
R572 1-218-941-81 METAL CHIP 100 5% 1/16W R1339 1-218-941-81 METAL CHIP 100 5% 1/16W
R573 1-218-941-81 METAL CHIP 100 5% 1/16W R1340 1-218-941-81 METAL CHIP 100 5% 1/16W

R574 1-218-941-81 METAL CHIP 100 5% 1/16W R1341 1-218-941-81 METAL CHIP 100 5% 1/16W
R575 1-218-941-81 METAL CHIP 100 5% 1/16W R1343 1-218-953-11 METAL CHIP 1K 5% 1/16W
R576 1-216-864-11 SHORT CHIP 0 R1346 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R577 1-218-981-81 METAL CHIP 220K 5% 1/16W R1350 1-218-941-81 METAL CHIP 100 5% 1/16W
R581 1-218-977-11 METAL CHIP 100K 5% 1/16W R1352 1-216-864-11 SHORT CHIP 0

R583 1-218-961-11 METAL CHIP 4.7K 5% 1/16W R1353 1-218-990-81 SHORT CHIP 0
R584 1-218-933-11 METAL CHIP 22 5% 1/16W R1354 1-218-949-11 METAL CHIP 470 5% 1/16W

35
CDX-G3100UE/G3100UV/G3150UP/G3150UV
Ver. 1.1
MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R1355 1-218-949-11 METAL CHIP 470 5% 1/16W PARTS FOR INSTALLATION AND CONNECTIONS
R1356 1-218-949-11 METAL CHIP 470 5% 1/16W **************************************
R1357 1-218-949-11 METAL CHIP 470 5% 1/16W
501 X-2583-962-1 FRAME ASSY, FITTING
R1358 1-216-864-11 SHORT CHIP 0 502 4-276-003-02 KEY (FRAME) (1 piece)
R1359 1-216-864-11 SHORT CHIP 0 503 4-461-753-01 COLLAR
R1360 1-216-864-11 SHORT CHIP 0 504 1-846-032-11 CONNECTION CABLE (ISO) (POWER CORD)
R1361 1-216-296-11 SHORT CHIP 0 (G3100UE/G3100UV)
R1362 1-216-864-11 SHORT CHIP 0 504 1-846-978-11 CONNECTION CABLE, AUTOMOBILE
(POWER CORD) (G3150UP/G3150UV)
R1363 1-218-990-81 SHORT CHIP 0
R1364 1-218-941-81 METAL CHIP 100 5% 1/16W 505 X-2584-360-1 SCREW ASSY (BS), FITTING
(G3100UE/G3100UV)
< TUNER UNIT > 505 X-2587-114-1 SCREW ASSY (BS4), FITTING
(G3150UP/G3150UV)
TU01 A-2057-353-A TUX-DSP04 (TUNER UNIT) 506 3-349-410-11 BUSHING
507 3-934-325-21 SCREW, +K (5X8) TAPPING (1 piece)
< VIBRATOR > (G3150UP/G3150UV)

X501 1-814-827-21 QUARTZ CRYSTAL UNIT (32.768 kHz)

X502 1-814-714-11 QUARTZ CRYSTAL UNIT (9.25 MHz) 501 502
X601 1-814-304-11 VIBRATOR, CRYSTAL (12 MHz)
X701 1-795-561-21 VIBRATOR, CERAMIC (16.934 MHz)
*************************************************************

MISCELLANEOUS
FITTING FRAME ASSY KEY (FRAME)
************** u1 u2

FFC1 1-846-819-41 CABLE FLEXIBLE FLAT (27 CORE) 503

(Length: 80 mm)
FP1 A-2058-343-A PANEL OVERALL ASSY, FRONT (G3100UV)
FP1 A-2058-344-A PANEL OVERALL ASSY, FRONT (G3100UE)
FP1 A-2058-345-A PANEL OVERALL ASSY, FRONT (G3150UV: E)
FP1 A-2058-346-A PANEL OVERALL ASSY, FRONT (G3150UP) COLLAR
u1

FP1 A-2058-347-A PANEL OVERALL ASSY, FRONT (G3150UV: MX)

(G3100UE/G3100UV) (G3150UP/G3150UV)
FP1 A-2058-348-A PANEL OVERALL ASSY, FRONT (G3150UV: EA)
FP1 A-2058-349-A PANEL OVERALL ASSY, FRONT (G3150UV: IND) 504 504
FU1 1-523-227-11 MINI FUSE (BLADE TYPE) (10 A/32 V)
PW1 1-846-032-11 CONNECTION CABLE (ISO) (POWER CORD)
(G3100UE/G3100UV)
POWER CORD (ISO) POWER CORD
PW1 1-846-978-11
CONNECTION CABLE, AUTOMOBILE u1 u1
(POWER CORD) (G3150UP/G3150UV)
*************************************************************
(G3100UE/G3100UV)
ACCESSORIES 505
************
506
1-489-810-22 REMOTE COMMANDER (RM-X211) (G3150UV)
4-542-303-21 OPERATING INSTRUCTION (ENGLISH, FRENCH,
GERMAN, DUTCH, ITALIAN) (AEP, UK) FITTING SCREW BUSHING
4-542-303-31 OPERATING INSTRUCTION u1 u1
(RUSSIAN, UKRAINIAN) (RU) FITTING SCREW ASSY (BS)
4-542-303-41 OPERATING INSTRUCTION (ENGLISH, SPANISH) u1
(E, MX, IND)
4-542-303-51 OPERATING INSTRUCTION (ENGLISH) (AUS)
(G3150UP/G3150UV)
4-542-303-62
OPERATING INSTRUCTION 505
(ENGLISH, ARABIC, PERSIAN) (EA)
*************************************************************
506 507

FITTING SCREW BUSHING +K5 u8

u1 u1 u4
FITTING SCREW ASSY (BS4)
u1

36
 CDX-G3100UE/G3100UV/G3150UP/G3150UV

MEMO

37
CDX-G3100UE/G3100UV/G3150UP/G3150UV

REVISION HISTORY

Ver. Date Description of Revision

1.0 2014.08 New
1.1 2014.11 Addition of CDX-G3150UP
Change of Part No. for Ref. No. R1308 on the MAIN board
Change of Part No. for OPERATING INSTRUCTION (Saudi Arabia model)
Change of Part No. for KEY (FRAME) (Ref. No. 502) (SMR-14036)

How to search for a contact point of signal lines or the like in DIAGRAMS SECTION
If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use
the PDF file search function to find one.

e.g.) If a contact point is shown as , follow the procedure below.

Procedure:
1. Press the [F] key while pressing the [Ctrl] key.
2. Input “>001Z” in the search box and press the [Enter] key.
3. The relevant part (page), where the contact point is shown, appears.
Note: If you still see the original page, press the [Enter] key again.