Waterproofing

MS Polymer Based
AquaBlocker SMP Based Liquid Waterproofing Membrane 16
AquaBlocker Liquid SMP Based Liquid Waterproofing Membrane 17
RenoGrund PU Rapid SMP Based Liquid Waterproofing Membrane Primer 18
Cement Based
CemenTech C1 1 Comp. Waterproofing Mortar 22
CemenTech C1 Duo 1 Comp. Crystallized Waterproofing Mortar 23
CemenTech Sulfat Sulfate-Resistant Waterproofing Mortar 24
CemenTech C2 Combi 2 Comp. Semi-Flexible Waterproofing Mortar 25
CemenTech C2 2 Comp. Flexible Waterproofing Mortar 26
CemenTech C2 Extra 2 Comp. Extra Flexible Waterproofing Mortar 27
CemenTech C2 UV 2 Comp. UV Resistant Extra Flexible Waterproofing Mortar 28
CemenTech C2 Duo 2 Comp. Crystallized Waterproofing Mortar 29
CemenTech X Water Plug 30
KATKILAR
BoscoMix P152 Crystallized Admix 32
PU Based
BoscoPur UniSeal PU Based Liquid Waterproofing Membrane 35
BoscoPur PowerFiber PU Based Patching and Detailing Membrane 36
BoscoPur Fabric Textile Reinforcement 36
BoscoPur Top - HT PU Based Liquid Waterproofing Top-coating Membrane 37
BoscoPur PurPrimer 1C PU Based Primer for Porous Substrates 38
BoscoPur EpoPrimer 2C Water-Borned Epoxy-Based Primer for Porous Substrates 39
BoscoPur GreenSeal E.F.P. Polyurethane-Based Liquid Waterproofing Membrane 40
BoscoPur BitumFlex PU Based, Bitumen Extended Waterproofing Membrane 41
AquaRoll PU Mono PU Based Waterproofing Coating 43
AquaRoll PU Prim - PP PU Based Primer for Porous Substrates 44
AquaRoll PU Prim - MP Silane-Based Primer for Non-Porous, Glazed Substrates 44
Acrylic Based
AquaRoll Easy - UV UV Resistant Liquid Membrane 45
AquaRoll Saniter Liquid Membrane 46
Bitumen Based
AquaRoll B1 Flex 1 Comp. Bituminous Flexible Coating 48
AquaRoll BC2 Performa 2 Comp. Fiber-Reinforced Bituminous Thick Coating 49
AquaRoll BC2 2 Comp. Bituminous Thick Coating 50
AquaRoll BituCoat 32 2 Comp. Bituminous Coating 51
complementary Products
FlexBand MonoFlex TPE Based Waterproofing Tape for Dilatation Joints 52
FlexBand L Flexible Sealing Band 53
FlexBand V Flexible Collar 53
FlexBand H Flexible Collar 53
FlexBand 90 Flexible Inner Corner Band 54
FlexBand 270 Flexible Outer Corner Band 54
FlexBand DL 140 / DL 240 Flexible Expansion Joint Band 54
FlexBand Butil Butyl Band 55
SwellTape Swelling Tape 55
NEW Swell_PolyTape Polymer Based Swelling Tape 56
 Waterproofing Solution Partner
‘‘AquaBlocker’’

- Solvent free.
- Non-bituminous.
- Silicone free.
- Highly elastic.
- Labour-saving.
- Spreadable with a roller easily.
- Crack bridging up to 10 mm.
- Low consumption.
- Grabs all surfaces.
- Unaffected by weather conditions.
- UV-resistant.
- Directly grabs the surface.
- Applicable in two layers.
- Ready-to-use.
- Fast curing.
- Hardens quickly.
- Odourless.

14 Bostik Build Catalogue

PRODUCTS AquaBlocker AquaBlocker Liquid

Description SMP Based Liquid Waterproofing Membrane SMP Based Liquid Waterproofing Membrane

- Interior and exterior, - Interior and exterior,

- Vertical applications, - Horizontal applications,
- Walls, - Foundations, basements and underground
- Basements and underground structures, structures,
- Wet areas. - Balconies and terraces,
- Wet areas.

Areas of
Application

- Resistant to weather conditions, - Resistant to weather conditions,

- Excellent bonding to all kind of surfaces, - Excellent bonding to all kind of surfaces,
- Excellent adhesive rstrength, - Excellent adhesive rstrength,
- Superior crack bridging ability, - Superior crack bridging ability,
- Resistant to UV lights. - Resistant to UV lights.

Features

Colour Light grey Light grey

TECHNICAL DATA

Applicable
Max. 2 mm Max 2 mm
thickness

Initial
4 Hours 4 Hours
Curing

Full
24 Hours 24 Hours
Curing

Coverage 1,5 - 1,8 kg / m² / mm 1,5 - 1,8 kg / m² / mm

Waterproofing

1 kg tin and 14 kg plastic bucket

Packaging 14 kg plastic bucket in aluminum packages
in aluminum packages.

1 1

Bostik Build Catalogue 15

 AquaBlocker & AquaBlocker Liquid
SMP Based Liquid Waterproofing Membrane

Product Description
Aqua Blocker® is a solvent-, water- and bitumen-free, as
well as non-slump water-proofing sealant for buildings acc.
to DIN 18195. Aqua Blocker® liquid is a sealing compound for
horizontal surfaces. After it has cured completely, the sealant
will be impermeable to water, bridges cracks up to maximum
5 mm and is resistant to natural groundwater which is
aggressive to concrete.

Features
Based on the SMP technology, Aqua Blocker® combines the
reliable crack-bridging and waterproofing performance
of a traditional, thick-layer bituminous coating with the
unbeatable ease of handling and application of a bituminous
emulsion. The solvent-, water- and bitumen-free Aqua
Blocker® sticks very well on slightly humid substrates within
the temperature range of +5° and +35°C.
Aqua Blocker® is certified by the building supervisory
authority according to the “Prüfgrundsätze für
Bauwerksabdichtungen mit Flüssigkunststoffen“ (General
test procedures for watertight seals in buildings using fluid
plastics), issue 06/2006 as per the Construction Products List
A Part 2, 1.12 (abP) for seals according to DIN 18195 Part 4, Part
5 and Part 6.

Area of application TECHNICAL DATA

Waterproofing of buildings:
It is used to provide long-lasting protection of structural Color Light grey
elements in contact with soil, such as basements, buildings
without underground level, foundations, floor plates, 2 coatings with at least 1.0
Applicable thickness (mm)
connections, pipe bushings against ground moisture, retained mm thickness of each dry layer
water, water not under pressure and accumulating seepage
water according to DIN 18195. Crack Repairing (Without Bostik Max. 5 mm
FlexMesh mesh reinforcement) (dry coat thickness at 2,5 mm)
Vertical surfaces: The thixotropic Aqua Blocker® is used for Elongation @ Break (2 mm Film) > % 700
sealing vertical surfaces, e.g. basement retaining walls made
of masonry, concrete and impermeable concrete. Shore A hardness (28 days, 23°C
~30
and a relative humidity of 50%)
Horizontal surfaces: Aqua Blocker® liquid is used for sealing
larger horizontal surfaces, e.g. foundations, floor plates, as Drying time between first and
~8
vapour seal in the commercial area, as well as on balconies second coat (h)
and terraces under screeds in combination with tiles Full curing (h) ~ 24
and plates. It is also suitable for filling of settlement and
expansion joints in the commercial and industrial area as well. Application temperature Between +5°C and +35°C

Prefabricated concrete parts: AquaBlocker temperature during

Between +15°C and +25°C
Aqua Blocker® is certified by the building supervisory the application
authority as external, striped sealing of structural elements
made of concrete with high resistance to water penetration Resistance of hardened coating Between -25°C and +80°C
according to the Construction Products List A, part 2, item 1.4 Technical data are approximately provided according to a temperature
(abP) against pressing water, not pressing water and ground of +23°C and a relative humidity of 50%.
moisture.

Substrates: Masonry (according to DIN 1035 Part 1, Chapters

1-11), cellular concrete/-blocks, lime-sandstone/-blocks, Application
prefabricated concrete parts, concrete and watertight Do not process Aqua Blocker® / Aqua Blocker® liquid when
concrete. the temperature of the structural parts or the environment
is below +5°C. Aqua Blocker® is ready-for-use and can be
Preparing the substrate: used directly from the packaging. It should be evenly and
The mineral substrate must be solid, stable and plane, continuously applied in two layers using a short-haired
without any lumps of gravel, cavities, gaping cracks or burrs. velour roller. In the corner and wall areas, and for small repair
The surfaces to be coated must be free from any residues works, Aqua Blocker® can be applied using a broad brush or
of oil, formwork oil, grease, dust, sintered layers or other a brush. Aqua Blocker® liquid is directly poured out of the
separation layers. Joints in masonry surfaces must be solidly aluminum bag onto the substrate and is spread out with a
filled, edges and fillets (leg length at least 4 cm long) have notched trowel. It is evenly applied in two layers over the
to be rounded. Irregular masonry surfaces with numerous whole surface. You will need about 1.5 kg/m² per mm of layer
exposed parts and cavities, as well as and chip-offs and thickness. Allow the first coat to dry before the next coat is
defects should be filled or leveled prior to applying the Bostik applied. The ambient temperature and the temperature of
repairing mortars. Create the coves in the wall/bottom area the substrate should range between +5° C and +35° C. Press
at least 24 hours before the beginning of the sealing works the reinforcement fabric into the first coat of Aqua Blocker®
using the polymer-enriched Bostik SRM serie structural / Aqua Blocker® liquid over the whole surface. Aqua Blocker®
Waterproofing

repairing mortars. Against groundwater under negative / Aqua Blocker® liquid are not suitable for sealing of building
pressure, apply a two-layer surface sealing continuously joints. During processing the temperature of the material
from the front edge of the concrete base up to a height of should be between +15° and +25°C.
30 cm on the enclosing walls using the watertight Bostik
CemenTech serie sealing slurries. Aqua Blocker® / Aqua Hints for subsequent works:
Blocker® liquid can be applied directly on slightly damp Before starting the following works, allowed the Aqua
substrates without needing a primer. Avoid standing water. Blocker® / Aqua Blocker® liquid to dry completely (about
24 hours at +20°C / 50% rel. humidity). When the seal has
+5 - +35 C
2
Max. 2mm
1 2

16 Bostik Build Catalogue

reached its full load-bearing capacity, it must be protected Technical Service for machine use.
in accordance with DIN 18 195 using suitable protective,
drainage or insulating sheets. When doing so, single-point Cleaning: Remove cured mechanical residues using a spatula
and linear load concentrations should be avoided. The sheets or similar tool.
can be fixed using Aqua Blocker®.
Notes:
Field of application - Roof sealing: Bituminous substrates can change the color of the Aqua
For sealing and for repairs of chimney connections, individual Blocker®. This discoloration is not a technical defect. Humid
roof lights, edge and corner areas on flat roofs, rainwater substrates can cause bubbles within the roof area. If the
gutters, roof connections, as well as horizontal surfaces. minimum thickness of the layer is not kept, cracks and
structural failures can occur Pay attention to migration,
Repairs of small areas: plasticizers, negative interactions, permigration between the
For instance, small-surface repairs refer to small roofs sealed substrates and the Aqua Blocker®. Only walk on roof
of garden sheds, max. 1 mm wide cracks, as well as partial surfaces restored with Aqua Blocker®/ Aqua Blocker® for
damages of the existing roof seals and the applications maintenance purposes.
mentioned before.
The substrate has to be rigid, capable of bearing loads and Coverage
free from separating layers. After cleaning the substrates Approx. 1,5 kg / m² for each 1 mm thickness.
usually existing in the roof area, e.g. old rigidly laying sanded
bituminized sheets/ bituminized sheets covered with slate Packaging
chippings, aged PVC-sheets, concrete, and wood, can be Aqua Blocker: 1 kg tin and 14 kg plastic bucket in aluminum
repaired with Aqua Blocker®. To check the adhesion on PIB-/ packages.
EPDM-sheets we recommend performing tests yourself. Aqua Blocker Liquid: 14 kg plastic bucket in aluminum
Remove old loosely laying sheets completely. Keep a packages.
minimum layer thickness of 2 mm after applying the Aqua
Blocker® twice. Humid substrates (also due to humidity Storage
which penetrates from behind) can cause bubbles.. - They should be protected for water, frost and adverse
weather conditions.
Surface restoration of concrete substrates: - They should be kept dry and cool on wooden pallets at
The mineral substrate must be solid, stable and dry, without between +10°C and +25°C in moisture free conditions.
any lumps of gravel, cavities, gaping cracks or burrs. The - The torn and opened products should be closed
surfaces to be coated must be free from any residues of immediately and consumed first.
oil, formwork oil, grease, dust, sintered layers or other - Maximum 3 buckets should be stocked on each other.
separating layers. Chip-offs and defects should be filled - Shelf life is maximum 12 months conditional to complying
or leveled prior to applying the Bostik repairing mortars. with the above mentioned storage conditions.
We recommend filling the pores of dry concrete with
Bostik Renogrund PU as priming coat. The primer must
be completely dry (about 8 hours at 20°C/50% relative air
humidity) before Aqua Blocker® / Aqua Blocker® liquid can be
applied. After priming, apply the first coat of Aqua Blocker®
/ Aqua Blocker® liquid within 36 hours. When the first coat
can be walked on, the second coat will be applied. Keep a
minimum layer thickness of 2 mm. If the surfaces are larger
than 25 m², embed the reinforcement fabric over the whole
surface into the first layer including the upturn edges and
connections. Keep a minimum layer thickness of 2.5 mm (incl.
fabric).

Surface restoration of old substrates:

The substrate has to be rigid, stable and free from other
separating layers. After cleaning, the following substrates
usually existing in the roof area, e.g. old rigidly laying
bituminized sheets which are sanded or with slate chips, and
aged PVC-sheets can be repaired with Aqua Blocker®. We
recommend applying Bostik Renogrund PU primer on the
dry substrate. The primer must be cured (about 8 hours at
20°C/50% relative air humidity) before Aqua Blocker® / Aqua
Blocker® liquid can be applied. After priming, the first layer
of Aqua Blocker® / Aqua Blocker® liquid has to be applied
within 36 hours. Embed the reinforcement fabric over the
whole surface in the first layer including the upturn edges
and connections. After the first coat can be walked on, the
second coat will be applied. Keep a minimum layer thickness
of 2.5 mm (incl. the fabric). Using this structure, 4 mm wide
cracks can be bridged. For repairing of sanded bituminized
sheets it will be necessary to apply another thin layer of Aqua
Blocker® / Aqua Blocker® liquid. This layer must completely
be covered with slate chippings.

Application
Do not process Aqua Blocker® / Aqua Blocker® liquid when
Waterproofing

the temperature of the structural parts or the environment

is below +5°C. Aqua Blocker®/ Aqua Blocker® liquid is ready-
for-use and can be used directly from the packaging. Aqua
Blocker® is applied using the short-haired velour roller, for
Aqua Blocker® liquid use the notched Trowel

Application with machines: Bostik AquaBlocker can be

sprayed by using a airless sprayers. Consult to Bostik

Bostik Build Catalogue 17

 RenoGrund PU Rapid
SMP Based Liquid Waterproofing Membrane Primer

Product Description
RenoGrund PU is a solvent-free, one-component primer
for absorbent or non-absorbent surfaces such as calcium
sulphate screeds, concrete and cement. It is suitable for
humidity-resistant subfloors to prevent the humidity or
humidity content permanently which increases in capillaries
up to maximum 4,5cm% when spread in 3 layers. Regarding
the prevention of the humidity increasing in capillaries, it is
not suitable for screeds on floor heating systems and calcium
sulphate screeds.

Application areas
- In absorbent surfaces,
- In mineral surfaces, such as concrete, plaster, etc.

Features
- One-component.
- Solvent-free.
- Odourless.
- Highly adhesive.

Preparing the substrate

- The substrates should be smooth, clean, crack-free and
strong enough to bear their own weight.
- Measures for negative water pressure should be taken
according to the current standards. TECHNICAL DATA
- Calcium sulphate-based screeds should be prepared
mechanically beforehand and cleaned thoroughly with a Color Red brown
vacuum cleaner. The instructions of screed manufacturers
should be followed. Unit volüme weight 1,2 ± 0,2
- Primers do not make non-standard surfaces “ready for
flooring”. However, they are used for obtaining optimum Viscosity (cp) ~4
results with covering products that are supposed to be used Full dry after (h) 1-2
on appropriate substrates.
Compatibility for floor heating
As priming: Compatible
Application radiator
- Bostik RenoGrund PU Rapid should be applied on the
substrate smoothly. In the meanwhile, water accumulation Technical data are approximately provided according to a temperature
should be prevented. of +23°C and a relative humidity of 50%.
- The application should be carried out with a notched trowel
or a velvet roller. If it is spread with a trowel for optimum - Shelf life is maximum 6 months conditional to complying
substrate priming or a closed priming film with filling with the above mentioned storage conditions.
purposes, no rollers should be used afterwards.
- Bostik RenoGrund PU Rapid should be applied for three
times as moisture retarder. After each layer, some drying
period, which not less than 4 – 6 hours, is required before 24
hours.
- The following application should be carried out in horizontal
position unlike the spreading direction of the previous
application. And then, in order to obtain a non-slippery
substrate for the following processes, dry sand (i.e. Bostik QS)
should be sprinkled equally onto still wet upper surface of
the third sprinkling process.
- The remaining dry sand should be vacuumed right after
the spreading process of priming and moisture retarding
minimum 8 – 12 hours later. Unless any other application is
needed, the following application can be carried out directly
within 24 hours on Bostik RenoGrund PU Rapid following the
last layer.

Coverage
Approx. 0,150 kg/m² as primer.
Approx. 0,4 – 0,5 kg/m² as moisture retarder.
The coverage amounts are theoretical and it is recommended
to do coverage-controlled sample application before
treatment.

Packaging
11 kg plastic drums.

Storage
Waterproofing

- They should be protected for water, frost and adverse

weather conditions.
- They should be kept dry and cool on wooden pallets at
between +10°C and +25°C in moisture free conditions.
- The torn and opened products should be closed
immediately and consumed first.
- Maximum 3 buckets should be stocked on each other.

+5 - +35 C

1 2

18 Bostik Build Catalogue

 Application - AquaBlocker

STEP:1 STEP:2 STEP:3

Bostik Aquablocker is resistant to UV Bostik Aquablocker Liquid adheres on Bostik Aquablocker is permanently
lights and exterior weather conditions. all kind of materials strongly, no primer elastic with excellent crack bridging
It can be used in all kind of roof finishing required. It forms one-piece, no-joint, ability. It is used safely for insulating and
details safely. continuous waterproofing layer. repairing the joints of the materials.

STEP:4 STEP:5 STEP:6

Bostik Aquablocker is used in wet areas Bostik Aquablocker is used safely for Bostik Aquablocker is permanently
such as toilets, bathrooms, kitchens basic insulation of basements and elastic. It is used for blocking the
prior to tile-ceramics applications as a protection of underground structures possible water leakages in moveable
waterproofing agent. from negative effects of water. No joints and horizontal-vertical
primer required. It bonds to all kind of connection points with cracking risk.
surface robustly.
Waterproofing

Bostik Build Catalogue 19

 PRODUCTS
CemenTech CemenTech CemenTech CemenTech
C1 C1 Duo Sulfat C2 Combi

One-Component Two-Component
One-Component Sulfate-Resistant
Description Crystallized Semi-Flexible
Waterproofing Mortar Waterproofing Mortar
Waterproofing Mortar Waterproofing Mortar

-Interior and exterior, - Interior and exterior, - Exterior, - From positive side
- From positive side - From negative and - From positive side only,
only, positive side, only, - Vertical and
- In foundations, - In foundations - In foundations, horizantal,
basements, basements, basements, - In foundations,
underground underground underground structures basements,
Areas of structures, structures, - Especially in underground
Application - Balconies and - Balconies and wastewater tanks and structures
terraces, terraces, domestic waste - Balconies and
- Water tanks, - Water tanks, channels, terraces,
reservoirs and storage reservoirs and - Water tanks, reservoirs - Water tanks,
tanks, storage tanks, and storage tanks, reservoirs and
- In restoration works - In restoration works - In all surfaces where storage tanks,
for old structures. for old structures. sulphate resistance is - In restoration works
required. for old structures.

- Resistant to weather - Resistant to weather - Resistant to weather - Semi- Flexible,

conditions, conditions, conditions, - Provides impermeability
- Excellent water - Excellent water - Excellent water against the pressured
vapour permeability, vapour permeability, vapour water effect,
- Prevents - Resistant to adverse
- Prevents humidity and humidity and water permeability,
water accumulation, - Resistant to sulphate. weather conditions,
accumulation, - High adhesion quality,
Features - Suitable for using with - Suitable for using strongly adheres to
trowel, with brush and roller, surfaces,
- Liquid consistency. - It forms one-piece, - Not corrosive for steel
no-joint and a whole
waterproofing layer by and reinforcement,
penetrating into - High abrasion resistance
concrete and mineral Suitable for direct contact
based surfaces. with freshwater, without
any coverings.

Color Grey Light red Black Grey

KURU BİRİM
HACİM 1,4 ± 0,2 kg / lt 1,3 ± 0,2 kg / lt 1,4 ± 0,2 kg / lt 1,3 ± 0,2 kg / lt
AĞIRLIĞI
TECHNICAL DATA

ISLAK BİRİM
HACİM 1,9 ± 0,2 kg / lt 1,9 ± 0,2 kg / lt 2,0 ± 0,2 kg / lt 1,8 ± 0,2 kg / lt
AĞIRLIĞI

KURUMA
SÜRESİ
~ 24 Hour ~ 24 Hour ~ 24 Hour ~ 24 Hour

YAPIŞMA
MUKAVEMETİ
≥ 1 N / mm² ≥ 1 N / mm² ≥ 1,5 N / mm² ≥ 2 N / mm²

SU KARIŞIM
5 kg
ORANI
6,0 - 6,5 lt 6,5 - 7,0 lt 5,5 - 7,0 lt (white-coloured liquid
emulsion)

Coverage 1,5 - 2,0 kg / m² / mm 1,5 - 2,0 kg / m² / mm 1,5 - 2,0 kg / m² / mm 1,5 - 2,0 kg / m² / mm

Waterproofing

20 kg craft bag
Packaging 25 kg craft bag 25 kg craft bag 25 kg craft bag 5 kg plastic drum

2K
A B
6 6 7
Lt Lt Lt

20 Bostik Build Catalogue

 CemenTech CemenTech CemenTech CemenTech
C2 C2 Extra C2 UV C2 Duo

Two-Component Extra Two-Component UV Two-Component

Two-Component Flexible Flexible Waterproofing Resistant Extra Flexible Crystallized Waterproofing
Waterproofing Mortar Mortar Waterproofing Mortar Mortar

- Exterior, - Exterior, - From positive side only, - Interior and exterior,

- From positive side only, - From positive side only, - Both vertical and horizontal, - Both in positive and
- In foundations, basements, - In foundations, - In wet volumes, negative sides,
underground structures, basements, underground - In continuously wet, humid - Balconies and terraces,
- Balconies and terraces, structures, and damp areas such as garage, - Water tanks, pools,
- Water tanks, reservoirs and - Balconies and terraces, balcony, terrace and cellar; and reservoirs and storage
storage tanks, - Water tanks, reservoirs sunny areas, tanks,
- In restoration works for and storage tanks, - Water tanks, pools, reservoirs - In foundations,
old structures. - In restoration works for and storage tanks, external walls of cellars,
old structures. - In foundations, basement underground and surface
walls, underground and surface construction works,
construction works, - In restoration and
- In bridges and sustaining walls. renovation works of old
structures.

- Flexible, - Extra flexible, - Extra flexible. - Resistant to heavy

- Resistant to weather - Resistant to weather - Provides impermeability weather conditions,
conditions, conditions, against the pressured water - Excellent water vapour
- Excellent water vapour - Excellent water vapour effect. permeability,
permeability, permeability, - Fireproof - Prevents humidity and
- Prevents humidity and - Prevents humidity and water water accumulation,
water accumulation, accumulation, - Suitable for using with
- High abrasion strength. - High abrasion resistance, brush and roller,
- Excellent crack bridging ability, - Prevents wetness and
- Enhanced resistance to water accumulation on
pressured water, concrete and
- Suitable for direct contact cement-based plastered
with freshwater, without any surfaces.
coverings.

Grey Light Green White Light Red

1,3 ± 0,2 kg / lt 1,2 ± 0,2 kg / lt 1,2 ± 0,2 kg / lt 1,3 ± 0,2 kg / lt

1,8 ± 0,2 kg / lt 1,7 ± 0,2 kg / lt 1,7 ± 0,2 kg / lt 1,8 ± 0,2 kg / lt

~ 24 Hour ~ 24 Hour ~ 24 Hour ~ 24 Hour

≥ 2 N / mm² ≥ 2 N / mm² ≥ 2 N / mm² ≥ 1,5 N / mm²

10 kg 10 kg 10 kg 9 kg
blue-colored liquid (white colored liquid (white colored liquid (white colored liquid
emulsion emulsion) emulsion) emulsion)

1,5 - 2,0 kg / m² / mm 1,5 - 2,0 kg / m² / mm 1,5 - 2,0 kg / m² / mm 1,5 - 2,0 kg / m² / mm

Waterproofing

25 kg craft bag 20 kg craft bag 25 kg craft bag 25 kg craft bag

10 kg plastic drum 10 kg plastic drum 10 kg plastic drum 9 kg plastic drum

2K 2K 2K 2K
A B A B A B A B

Bostik Build Catalogue 21

 CemenTech
C1
One-Component Waterproofing Mortar

Product description
It is cement based, one-component, plaster consistency,
grey-colored sealing slurry that is reinforced by polymeric
additives and used in the solution of problems arising from
capillary effects. It provides water insulation in garages,
terraces, foundations and basements. CemenTech C1 is
water-repellent and can be used from the positive side only.
Application areas
- In interior and exterior,
- On walls and grounds,
- In continuously wet, humid and damp areas such as balcony,
terrace and cellar,
- Small pools, small storage tanks and reservoirs,
- In foundations, external walls of cellars,
- Underground and surface construction works,
- In amelioration, restoration and renovation works of old
structures,
- In any kind of bonded and plastered surface such as stone
and stone-derivative brick, pumice brick, briquette, aerated
concrete, limestone, etc.
Features
- Reinforced with polymeric additives.
- Resistant to heavy weather conditions.
- Features hydraulic adhesion quality.
- Prevents wetness and water accumulation on cement-
based plastered surfaces.
- Prevents humidity and moisture permanently and
eliminates unpressurized and weak water leakages. TECHNICAL DATA
- Protects surfaces against destructive effects of humidity
and moisture. Color Grey
- Nonflammable. Applicable Thickness (mm) Max 6
Preparation of the substrate Recommended applicable thickness 2 (mm)
- The surfaces to be coated should be free of adhesive
preventive foreign substances such as dust, dirt, mould Dry Unit Volume Weight (kg / lt) 1,4 ± 0,2
oil, paint etc.; residues and wastes like cement, plaster and
concrete should also be removed. Wet Unit Volume Weight (kg / lt) 1,9 ± 0,2
- The sub-surfaces that are not strong enough to carry
themselves e.g. cracked plasters, weak surfaces, or residues Waiting Time in Container (min) ~ 30
of moss should be cleaned from the application surface.
- Surface should be slightly dampened before application. Drying Time (hour) ~ 24
- Aerated concrete, reinforced brick walls and other
substrates with similar absorbent features should be Carbondioxide Permeability (m) ≥ 50
dampened a few times.
Permeability to Water-vapour (m) Class I ; Sd <5
Application
- Powder form Bostik CemenTech C1 Waterproofing Mortar Adhesion Strength (28 days) > 1 (N / mm²)
should be poured slowly into a clean container filled with
water in suitable ambiance temperature and should be Capillary Water Absorption 0,1 (<0,1kg/m².h0,5)
mixed by means of a mixer with low cycle until a cluster-free
mixture is obtained. Mixture duration should be minimum Mixing water amount
6,0 – 6,5 lt
5 minutes. The mixture obtained at the end of the process (for 25 kg dry mortar)
should be rested for 3 minutes and mixed again until it
becomes homogenous for 2 minutes. Application temperature Between +5°C and +35°C
- Density amount and freezing time of the product vary
according to the emulsion amount. Resistance of hardened coating Between -25°C and +80°C
- The mixture should be applied on the surface with a spatula
or a steel trowel in at least two layers. Technical data are approximately provided according to a temperature
- The mortar that is freshly prepared with Bostik CemenTech of +23°C and a relative humidity of 50%.
C1 Waterproofing Mortar should be used within 30 minutes at
the latest.
- Regardless of the aim of the usage, the application Package
thickness should not be less than 2mm or more than 6 mm. Powder component in 25 kg craft bag, 64 bags in 1 palette
- Application should always be in two layers. The first layer (1600 kg/palette)
may be applied with a brush and the second layer with a
laying trowel. Storage
- Dry mortar bags should be protected for water, frost and
After application adverse weather conditions.
- Freshly applied surfaces should be protected against direct - They should be kept dry and cool on wooden pallets at
sun light, strong air stream, high air temperature (above between +10°C and +25°C in moisture free conditions.
+35˚C), rain and frost in the initial days. - The torn and opened products should be closed
- Any kind of plaster application on the application surface or immediately and consumed first.
ceramic tiling works should be performed 3 days later. - Maximum 8 bags should be stocked on each other.
- To obtain the recommended long term technical - Shelf life is maximum12 months conditional to complying
performance of the product, after the completion of the all with the above mentioned storage conditions.
application, the application and/or work should be covered
and protected with a suitable coating or covering (plaster,
Waterproofing

screed, ceramic, tile etc…) as early as possible (depending on

the product’s drying time within 3-7 days).
Coverage
Approximately 1,5 – 2,0 kg/m² per each 1 mm thickness.
Coverage amounts are theoretical values and it is
recommended that coverage-controlled sample application
is carried out before application.

+5 - +35 C

6 Max. 6 mm

Lt 1 12
5 30

22 Bostik Build Catalogue

CemenTech
C1 Duo
One-Component Crystallized Waterproofing Mortar

Product description
It is cement based, one-component, brush consistency,
light-red colored powder sealing slurry that is reinforced by
polymeric additives, and used in the solution of problems
arising from capillary effects. It is used in both positive
and negative side of waterproofing of garages, terraces,
foundations and basements. CemenTech C1 Duo creates
crystals that don’t melt within water when it reacts with
water and renders the concrete water-tight permanently
upon penetration of these crystals into the capillary vessels
of the concrete.
Application areas
- Interior and exterior,
- On walls, grounds or ceilings,
- In continuously wet, humid and damp areas such as garage,
balcony, terrace and cellar,
- Water tanks, pools, reservoirs and storage tanks,
- In foundations, external walls of cellars, underground and
surface construction works,
- In amelioration, restoration and renovation works of old
structures
Features
- Reinforced with polymeric additives.
- Produces crystals that do not melt in water when reacted
with water.
- When applied on lean concrete, as soon as getting cured,
it silicatizes the free lime on the concrete and makes it
impenetrable along the edge. TECHNICAL DATA
- Resistant to heavy weather conditions.
- Features hydraulic adhesion quality. Color Light red
- Used in any kind of bonded and plastered surface such as Applicable Thickness (mm) 2
stone and stone-derivative brick, pumice brick, briquette,
aerated concrete, limestone, etc. Dry Unit Volume Weight (kg / lt) 1,3 ± 0,2
- Prevents wetness and water accumulation on cement-
based plastered surfaces. Wet Unit Volume Weight (kg / lt) 1,9 ± 0,2
- Prevents humidity and moisture permanently and
eliminates unpressurized and weak water leakages. Waiting Time in Container (min) ~ 30
- Protects surfaces against destructive effects of humidity
and moisture. Drying Time (hour) ~ 24
- Nonflammable.
Carbondioxide Permeability (m) > 50
Preparation of the substrate
- The surfaces to be coated should be free of adhesive Permeability to Water-vapour (m) Class I ; Sd <5
preventive foreign substances such as dust, dirt, mould
oil, paint etc.; residues and wastes like cement, plaster and Adhesion Strength (28 days) ≥ 1 (N / mm²)
concrete should also be removed.
- The sub-surfaces that are not strong enough to carry Capillary Water Absorption < 0,1 (<0,1kg/m².h0,5)
themselves e.g. cracked plasters, weak surfaces, or residues
of moss should be cleaned from the application surface. Mixing water amount
- Surface should be slightly dampened before application. 6,5 – 7,0 lt
(for 25 kg dry mortar)
- Active water leakages should be clogged before application
with Bostik CemenTech X. Application temperature Between +5°C and +35°C
Application Resistance of hardened coating Between -25°C and +80°C
- Powder form Bostik CemenTech C1 Duo Waterproofing
Mortar should be poured slowly on fresh water (7 lt) that has Technical data are approximately provided according to a temperature
been put into a clean container filled with water in suitable of +23°C and a relative humidity of 50%.
ambiance temperature and should be mixed by means of a
mixer with low cycle until a cluster-free mixture is obtained.
Mixture duration should be minimum 5 minutes. The mixture Coverage
obtained at the end of the process should be rested for 3 Approximately 1,5 – 2,0 kg/m² per each 1 mm thickness.
minutes and mixed again until it becomes homogenous for 2 Coverage amounts are theoretical values and it is
minutes. recommended that coverage-controlled sample application
- The stirred mixture is ready for application after an aging is carried out before application.
time of 3 min.
- Application should be at least in two layers and should cover Package
the substrate of each layer properly. The first layer is applied Powder component in 25 kg craft bag, 64 bags in 1 palette
with a wall brush; after the first layer is dried completely, the (1600 kg/palette)
second layer should be reapplied with a wall brush.
Storage
Application with machine: - Dry mortar bags should be protected for water, frost and
CemenTech C1 Duo is suitable for use with sprayable machine. adverse weather conditions.
Consult Bostik Technical Service for machine use. - They should be kept dry and cool on wooden pallets at
between +10°C and +25°C in moisture free conditions.
After applicatioN - The torn and opened products should be closed
- Freshly applied surfaces should be protected against direct immediately and consumed first.
sun light, strong air stream, high air temperature (above 9 Maximum 8 bags should be stocked on each other.
- Shelf life is maximum 12 months conditional to complying
Waterproofing

+35°C), rain and frost in the initial days.

- Any kind of plaster application on the application surface or with the above mentioned storage conditions.
ceramic tiling works should be performed 3 days later.
- To obtain the recommended long term technical
performance of the product, after the completion of the all
application, the application and/or work should be covered
and protected with a suitable coating or covering (plaster,
screed, ceramic, tile etc…) as early as possible (depending on
the product’s drying time within 3-7 days).

7 max. 2 mm

Lt 5 1 12
30

Bostik Build Catalogue 23

 CemenTech
Sulfat
Sulfate-Resistant Waterproofing Mortar

Product description
It is cement based, one-component, water-repellent,
sulfate-resistant, black-colored sealing slurry that is
reinforced by polymeric additives and used in the solution
of waterproofing problems arising from capillary effect.
It provides water insulation in garages, terraces and
foundations. CemenTech Sulfat is resistant to mechanical
effects and chemicals in domestic wastes and water, and can
be used from the positive side only.

Application areas
- Exteriors only,
- On walls, floors or ceilings,
- In protection of upper surfaces of the channels and in
formation of a waterproofing coating,
- In the water bodies of domestic wastes and covering of the
reinforced concrete pipes,
- In protection of waste water pipes and channels against
sulfate wastes,
- In the tanks of rain water and waste water,
- In continuously wet, humid and damp areas such as garage,
balcony, terrace and cellar,
- Water tanks, pools, reservoirs and storage tanks,
- In foundations, external walls of basements,
- In underground and surface construction works,
- In amelioration, restoration and renovation works of old TECHNICAL DATA
structures,
- In any kind of bonded and plastered surface such as stone Color Black
and stone-derivative brick, pumice brick, briquette, aerated
concrete, limestone, etc. Applicable Thickness (mm) Max 6
Recommended applicable thickness 2 (mm)
Features
- Resistant to sulfate. Dry Unit Volume Weight (kg / lt) 1,4 ± 0,2
- Reinforced with polymeric additives.
- Resistant to heavy weather conditions. Wet Unit Volume Weight (kg / lt) 2,0 ± 0,2
- Hydraulic cementing quality.
- Nonflammable. Waiting Time in Container (min) ~ 30
Drying Time (hour) ~ 24
Preparation of the substrate
- The surfaces to be coated should be free of adhesive Adhesion Strength (28 days) ≥ 1,5 (N / mm²)
preventive foreign substances such as dust, dirt, mould
oil, paint etc.; residues and wastes like cement, plaster and Special mixture emulsion amount
concrete should also be removed. (for 25 kg dry mortar)
- The sub-surfaces that are not strong enough to carry - For brush consistency application 6,0 – 7,0 lt
themselves e.g. cracked plasters, weak surfaces, or residues - For trowel consistency application 5,5 – 6,0 lt
of moss should be cleaned from the application surface.
Application temperature Between +5°C and +35°C
- Surface should be slightly dampened before application.
- Aerated concrete, reinforced brick walls and other Resistance of hardened coating Between -25°C and +80°C
substrates with similar absorbent features should be
dampened a few times. Technical data are approximately provided according to a temperature
of +23°C and a relative humidity of 50%.
Application
- Powder form Bostik CemenTech Sulfat Waterproofing performance of the product, after the completion of the all
Mortar should be poured slowly into a clean container filled application, the application and/or work should be covered
with water in suitable ambiance temperature, and should and protected with a suitable coating or covering (plaster,
be mixed by means of a mixer with low cycle until a cluster- screed, ceramic, tile etc…) as early as possible (depending on
free mixture is obtained. Mixing time should be minimum the product’s drying time within 3-7 days).
5 minutes. The mixture obtained at the end of the process
should be rested for 3 minutes and mixed again until it Coverage
becomes homogenous for 2 minutes. Approximately 1,5 – 2,0 kg/m² per each 1 mm thickness.
- The prepared mortar should be applied on the surface in Coverage amounts are theoretical values and it is
minimum two layers with a spatula or steel trowel. recommended that coverage-controlled sample application
- The mortar that is freshly prepared with Bostik CemenTech is carried out before application.
Sulfat Waterproofing Mortar should be used within 30
minutes at the latest. Package
- Regardless of the aim of the usage, the application Powder component in 25 kg craft bag, 64 bags in 1 palette
thickness should not be less than 2mm or more than 6 mm. (1600 kg/palette)
- Application should always be in two layers. The first layer
may be applied with a brush and the second layer with a Storage
laying trowel. - Dry mortar bags should be protected for water, frost and
Waterproofing

adverse weather conditions.

After application - They should be kept dry and cool on wooden pallets at
- Freshly applied surfaces should be protected against direct between +10°C and +25°C in moisture free conditions.
sun light, strong air stream, high air temperature (above - The torn and opened bags should be closed immediately and
+350C), rain and frost in the initial days. consumed first.
- Any kind of plaster application on the application surface or - Maximum 8 bags should be stocked on each other.
ceramic tiling works should be performed 3 days later. - Shelf life is maximum12 months conditional to complying
- To obtain the recommended long term technical with the above mentioned storage conditions.

7 max. 6 mm

Lt 5 1 12
30

24 Bostik Build Catalogue

CemenTech
C2 Combi
Two-Component Semi-Flexible Waterproofing Mortar

Product description
It is cement-based, two-component, semi flexible sealing
slurry that is reinforced by polymeric additives and used in
the solution of waterproofing problems. It can be from the
positive side only.

Application areas
- Interiors and exteriors
- From positive side only,
- Both vertical and horizontal,
- In wet volumes (eg.WC, bathroom, kitchen),
-In continuously wet, humid and damp areas such as balcony,
terrace and cellar,
- Water tanks, pools, reservoirs and storage tanks,
- In foundations, basement walls, underground and surface
construction works,
- In bridges and sustaining walls.

FeatureS
- Suitable for brush or spray use
- Resistant to heavy weather conditions.
- High adherence; strongly adheres to surfaces.
- Non-corrosive for steel and reinforcements
- High abrasion resistance.
- Flexible.
- Suitable for direct contact with freshwater, without any
coverings. TECHNICAL DATA
Preparation of the substrate Colour Grey
- The surfaces to be coated should be free of adhesive
preventive foreign substances such as dust, dirt, mould Applicable thickness (mm) Max 6
oil, paint etc.; residues and wastes like cement, plaster and Recommended applicable thickness 2 (mm)
concrete should also be removed.
- The sub-surfaces that are not strong enough to bear their Dry unit volume weight (kg / lt) 1,3 ± 0,2
own weight e.g. cracked plasters, weak surfaces, or residues
of moss should be cleaned from the application surface. Wet unit volume weight (kg / lt) 1,8 ± 0,2

Application Waiting time in container (min) ~ 30

- Powder form Bostik CemenTech C2 Combi Waterproofing Drying time (hour) ~ 24
Mortar should be poured slowly on liquid component (5
kg) that has been put into a clean container, and should be Permeability to water-vapour (m) Class I ; Sd <5
mixed by means of a mixer with low cycle until a cluster-free
mixture is obtained. Mixture duration should be minimum Adhesion strength (28 days) (N / mm²) ≥2
5 minutes. The mixture obtained at the end of the process
should be rested for 3 minutes and mixed again until it Capillary water absorption < 0,1 (<0,1kg/m².h0,5)
becomes homogenous for 2 minutes. Special mixture emulsion amount 5 kg (white-coloured
- Bostik CemenTech C2 Combi Waterproofing Mortar (for 20 kg powder component) liquid emulsion)
emulsion should be shaken well before use.
- Application should be at least two layers thick. After Application temperature Between +5°C and +35°C
applying the first layer, at least 4-6 hours should be rested
and second layer should be applied before waiting period Resistance of hardened coating Between -25°C and +80°C
exceeds 24 hours.
Technical data are approximately provided according to a temperature
- The cracks that might be formed in the event of application
of +23°C and a relative humidity of 50%.
to very wide surfaces should be prevented by means of
application by leaving joints. Joints should be filled with
flexible filling material. CoveragE
- On the moving grounds that have cracking risk, Bostik Approximately 1,5 – 2,0 kg/m² per each 1 mm thickness.
FlexMesh net can be applied as an intermediate layer Coverage amounts are theoretical values and it is
between the application with the aim of forming a water recommended that coverage-controlled sample application
isolation layer which is more flexible in order to meet the is carried out before application.
tensile stress.
- It shouldn‘t be applied to hot or frozen surfaces directly. Package
Powder component in 20 kg craft bag, 60 sets in 1 palette
Application with machine: Liquid component in 5 kg plastic drum.
CemenTech C2 Combi is suitable for use with sprayable
machine. Consult Bostik Technical Service for machine use. Storage
- Dry mortar bags should be protected for water, frost and
After application adverse weather conditions.
- Freshly applied surfaces should be protected against direct - They should be kept dry and cool on wooden pallets at
sun light, strong air stream, high air temperature (above between +10°C and +25°C in moisture free conditions.
+35°C), rain and frost in the initial days (at least 5 days). - The torn and opened products should be closed
- Any kind of plaster application on the application surface or immediately and consumed first.
Waterproofing

ceramic tiling works should be performed 3 days later. - Maximum 8 bags should be stocked on each other.
- To obtain the recommended long term technical - Shelf life is maximum 12 months conditional to complying
performance of the product, after the completion of the all with the above mentioned storage conditions.
application, the application and/or work should be covered
and protected with a suitable coating or covering (plaster,
screed, ceramic, tile etc…) as early as possible (depending on
the product’s drying time within 3-7 days).

2K
A B
max. 6 mm

5 1 12
30

Bostik Build Catalogue 25

 CemenTech
C2
Two-Component Flexible Waterproofing Mortar

Product description
It is cement based, two-component, composed of grey-
colored cementitious compound and blue-colored emulsion,
flexible sealing slurry that is reinforced by polymeric
additives and used in the solution of waterproofing problems.
CemenTech C2 is water-repellent and can be used from the
positive side only.
Application areas
- In interior and exterior,
- From positive side only,
- Both vertical and horizontal,
- In wet volumes,
- In continuously wet, humid and damp areas such as balcony,
terrace and cellar,
- Water tanks, pools, reservoirs and storage tanks,
- In foundations, basement walls, underground and surface
construction works,
- In bridges and retaining walls,
Features
- Suitable for brush and sprayable use
- Resistant to heavy weather conditions.
- High adhesion quality, strongly adheres to surfaces.
- High abrasion resistance.
- Flexible.
- Suitable for use in drinking waters.
TECHNICAL DATA
Preparation of the substrate
- The surfaces to be coated should be free of adhesive Color Grey
preventive foreign substances such as dust, dirt, mould
oil, paint etc.; residues and wastes like cement, plaster and Applicable thickness (mm) Max 6
concrete should also be removed.
- The sub-surfaces that are not strong enough to carry Recommended applicable thickness 2 mm
themselves e.g. cracked plasters, weak surfaces, or residues
of moss should be cleaned from the application surface. Dry unit volume weight (kg / lt) 1,3 ± 0,2

Application Wet unit volume weight (kg / lt) 1,8 ± 0,2

- Powder form Bostik CemenTech C2 Waterproofing Mortar
should be poured slowly on liquid component (10 kg) that has Waiting time in container (min) ~ 30
been put into a clean container filled, and should be mixed by Drying time (hour) ~ 24
means of a mixer with low cycle until a cluster-free mixture
is obtained. Mixture duration should be minimum 5 minutes. Carbondioxide permeability (m) >0
The mixture obtained at the end of the process should
be rested for 3 minutes and mixed again until it becomes Permeability to water-vapour (m) Class I ; Sd <5
homogenous for 2 minutes.
- Bostik CemenTeach C2 Waterproofing Mortar emulsion Adhesion strength (28 days) ≥ 1 (N / mm²)
should be shaken well before use.
- Application should be at least two layers thick. After Capillary water absorption 0,1 (<0,1kg/m².h0,5)
applying the first layer, at least 4-6 hours should be rested
and second layer should be applied before waiting period Crack bridging > 0,75
exceeds 24 hours.
- The cracks that might be formed in the event of application Special mixture emulsion amount 10 kg blue-colored liquid
to very wide surfaces should be prevented by means of (for 25 kg powder component) emulsion
application by leaving joints. Joints should be filled with
flexible filling material. Application temperature Between +5°C and +35°C
- On the moving grounds that have cracking risk, Bostik Resistance of hardened coating Between -25°C and +80°C
FlexMesh net can be applied as an intermediate layer
between the application with the aim of forming a water Technical data are approximately provided according to a temperature
isolation layer which is more flexible in order to meet the of +23°C and a relative humidity of 50%.
tensile stress.
- It shouldn‘t be applied to hot or frozen surfaces directly.
Package
Application with machine: Powder component in 25 kg craft bag, 64 sets in 1 palette
CemenTech C2 is suitable for use with sprayable machine. Liquid component in 10 kg plastic drum.
Consult Bostik Technical Service for machine use.
Storage
After application - Dry mortar bags should be protected for water, frost and
- Freshly applied surfaces should be protected against direct adverse weather conditions.
sun light, strong air stream, high air temperature (above - They should be kept dry and cool on wooden pallets at
+35°C), rain and frost in the initial days. between +10°C and +25°C in moisture free conditions.
- Any kind of plaster application on the application surface or - The torn and opened products should be closed
ceramic tiling works should be performed 3 days later. immediately and consumed first.
- To obtain the recommended long term technical - Maximum 8 buckets should be stocked on each other.
performance of the product, after the completion of the all - Shelf life is maximum 12 months conditional to complying
application, the application and/or work should be covered with the above mentioned storage conditions.
Waterproofing

and protected with a suitable coating or covering (plaster,

screed, ceramic, tile etc…) as early as possible (depending on
the product’s drying time within 3-7 days).
Coverage
Approximately 1,5 – 2,0 kg/m² per each 1 mm thickness.
Coverage amounts are theoretical values and it is
recommended that coverage-controlled sample application
is carried out before application.
2K
A B
max. 6 mm

5 1 12
30

26 Bostik Build Catalogue

CemenTech
C2 Extra
Two-Component Extra Flexible Waterproofing Mortar

Product description
It is cement based, two-component, composed of green-colored
cementitious compound and white-colored liquid emulsion,
extra flexible sealing slurry that is reinforced by polymeric
additives and used in the solution of waterproofing problems.
CemenTech C2 Extra is water-repellent and can be used from the
positive side only.
Application areas
- Interiors and exteriors
- From positive side only,
- Both vertical and horizontal,
- In wet areas (eg.WC, bathroom, kitchen),
- In continuously wet, humid and damp areas such as balcony,
terrace and cellar,
- Water tanks, pools, reservoirs and storage tanks,
- In bath and spa,
- In foundations, basement walls, underground and surface
construction works,
- In bridges and sustaining walls.
Features
- Suitable for brush or spray
- Extra flexible.
- Provides impermeability against the pressured water effect.
- Resistant to heavy weather conditions.
- High adhesion quality, strongly adheres to surfaces.
- High abrasion resistance.
- Suitable for direct contact with freshwater
- Crack bridging up to 1,5 mm. according to TS EN 14891
Standarts
- TS EN 1504-2 TECHNICAL DATA
- TS EN 14891
- Type:CM= Cementitious liquid-applied water impermeable Color Light green
products
- CLASS : O2P = Resistant to contact with chlorinated water, with
crack bridging ability at low temperature. Applicable thickness (mm) Max 6

Preparation of the substrate Recommended applicable

- The surfaces to be coated should be free of adhesive preventive 2
thickness (mm)
foreign substances such as dust, dirt, mould oil, paint etc.;
residues and wastes like cement, plaster and concrete should also Dry unit volume weight (kg / lt) 1,2 ± 0,2
be removed.
- The sub-surfaces that are not strong enough to carry Wet unit volume weight (kg / lt) 1,7 ± 0,2
themselves e.g. cracked plasters, weak surfaces, or residues of
moss should be cleaned from the application surface.
Waiting time in container (min) ~ 30
Application
- Powder form Bostik CemenTech C2 Extra Waterproofing Mortar Drying time (hour) ~ 24
should be poured slowly on liquid component (10 kg) that has
been put into a clean container filled, and should be mixed by Carbondioxide permeability (m) > 50
means of a mixer with low cycle until a cluster-free mixture is
obtained. Mixture duration should be minimum 5 minutes. The Permeability to water-vapour (m) Class I ; Sd <5
mixture obtained at the end of the process should be rested for
3 minutes and mixed again until it becomes homogenous for 2 Adhesion strength (28 days) (N / mm²) ≥2
minutes.
- Bostik CemenTech C2 Extra Waterproofing Mortar emulsion
should be shaken well before use. Capillary water absorption (<0,1kg/m².h0,5) < 0,1
- Application should be at least two layers thick. After applying
the first layer, at least 4-6 hours should be rested and second Water pressure 7 bar
layer should be applied before waiting period exceeds 24 hours.
- The cracks that might be formed in the event of application to Special mixture emulsion amount 10 kg
very wide surfaces should be prevented by means of application
by leaving joints. Joints should be filled with flexible filling white-colored liquid
material. (for 20 kg powder component)
- On the moving grounds that have cracking risk, Bostik FlexMesh emulsion
net can be applied as an intermediate layer between the
application with the aim of forming a water isolation layer which Application temperature Between +5°C and +35°C
is more flexible in order to meet the tensile stress.
- It shouldn‘t be applied to hot or frozen surfaces directly. Resistance of hardened coating Between -25°C and +80°C
Application with machine: Technical data are approximately provided according to a temperature
CemenTech C2 Extra is suitable for use with sprayable machine. of +23°C and a relative humidity of 50%.
Consult Bostik Technical Service for machine use.
After application
- Freshly applied surfaces should be protected against direct Package
smic, tile etc…) as early as possible (depending on the product’s Powder component in 20 kg kraft bag, 60 sets in 1 palette
drying time within 3-7 days). Liquid component in 10 kg plastic drum.

Coverage Storage
- Freshly applied surfaces should be protected against direct sun - Dry mortar bags should be protected for water, frost and
light, strong air stream, high air temperature (above +350C), rain adverse weather conditions.
and frost in the initial days (at least 5 days). - They should be kept dry and cool on wooden pallets at between
- Any kind of plaster application on the application surface or +10°C and +25°C in moisture free conditions.
ceramic tiling works should be performed 3 days later. - The torn and opened products should be closed immediately
- To obtain the recommended long term technical performance and consumed first.
of the product, after the completion of the all application, the - Maximum 8 bags should be stocked on each other.
- Shelf life is maximum 12 months conditional to complying with
Waterproofing

application and/or work should be covered and protected with a

suitable coating or covering (plaster, screed, ceramic, tile etc…) as the above mentioned storage conditions.
early as possible (depending on the product’s drying time within
3-7 days).
Coverage
Approximately 1,5 – 2,0 kg/m² per each 1 mm thickness.
Coverage amounts are theoretical values and it is recommended
that coverage-controlled sample application is carried out before
application.

2K
A B
max. 6 mm

5 1 12
30

Bostik Build Catalogue 27

 CemenTech
C2 UV
Two-Component UV Resistant Extra Flexible Waterproofing Mortar

Product description
It is cement-based, two-component, composed of white-
coloured cementitious compound and white-coloured liquid
emulsion, extra flexible and UV lights resistant sealing slurry
that is reinforced by polymeric additives It provides water
insulation in roof, terraces and balconies. CemenTech C2 UV is
water-repellent and can be used from the positive side only.
Application areas
- From positive side only,
- Both vertical and horizontal,
- In wet volumes (WC, bathroom, kitchen etc.),
- In continuously wet, humid and damp areas such as balcony,
terrace and cellar;
- Sunny areas,
- Water tanks, pools, reservoirs and storage tanks,
- In foundations, basement walls, underground and surface
construction works,
- In bridges and sustaining walls.
FeatureS
- Suitable for brush and sprayable use
- Extra flexible.
- Resistant to UV lights.
- Provides impermeability against the pressured water
effect.
- Resistant to heavy weather conditions.
- High adherence; strongly adheres to surfaces. TECHNICAL DATA
- Suitable for use without any coating on the drinking water
tank Colour White
- High abrasion resistance.
Applicable thickness (mm) Max 6
Preparation of the substrate
- The surfaces to be coated should be free of adhesive Recommended applicable thickness 2 mm
preventive foreign substances such as dust, dirt, mould
oil, paint etc.; residues and wastes like cement, plaster and Dry unit volume weight (kg / lt) 1,2 ± 0,2
concrete should also be removed.
- The sub-surfaces that are not strong enough to carry Wet unit volume weight (kg / lt) 1,7 ± 0,2
themselves e.g. cracked plasters, weak surfaces, or residues
of moss should be cleaned from the application surface. Waiting time in container (min) ~ 30
Drying time (hour) ~ 24
ApplicatioN
- Bostik CemenTech C2 UV Waterproofing Mortar in powder Carbondioxide permeability (m) > 50
state should be poured slowly on liquid component (10
kg) that has been put into a clean container, and should be Permeability to water-vapour (m) Class I ; Sd <5
mixed by means of a mixer with low cycle until a cluster-free
mixture is obtained. Mixture duration should be minimum Adhesion strength (28 days) (N / mm²) ≥2
5 minutes. The mixture obtained at the end of the process
should be rested for 3 minutes and mixed again until it Crack bridging ≥2
becomes homogenous for 2 minutes.
- Bostik CemenTech C2 UV Waterproofing Mortar emulsion Water pressure 7 bar
should be shaken well before use.
- Application should be at least two layers thick. After Special mixture emulsion amount 10 kg (white-coloured
applying the first layer, at least 4-6 hours should be rested (for 25 kg powder component) liquid emulsion)
and second layer should be applied before waiting period Application temperature Between +5°C and +35°C
exceeds 24 hours.
- The cracks that might be formed in the event of application Resistance of hardened coating Between -25°C and +80°C
to very wide surfaces should be prevented by means of
application by leaving joints. Joints should be filled with Technical data are approximately provided according to a temperature
flexible filling material. of +23°C and a relative humidity of 50%.
- On the moving grounds that have cracking risk, Bostik
FlexMesh net can be applied as an intermediate layer
between the application with the aim of forming a water Coverage
isolation layer which is more flexible in order to meet the Approximately 1,5 – 2,0 kg/m² per each 1 mm thickness.
tensile stress. Coverage amounts are theoretical values and it is
- It shouldn‘t be applied to hot or frozen surfaces directly. recommended that coverage-controlled sample application
is carried out before application.
Application with machine:
CemenTech C2 UV is suitable for use with sprayable machine. Package
Consult Bostik Technical Service for machine use. Powder component in 25 kg craft bag, 64 sets in 1 palette
Liquid component in 10 kg plastic drum.
After application
- Freshly applied surfaces should be protected against Storage
direct sun light, strong air stream, high air temperature - Dry mortar bags should be protected for water, frost and
(above +35°C), rain and frost in the initial days (at least 5 adverse weather conditions.
days). - They should be kept dry and cool on wooden pallets at
Waterproofing

- Any kind of plaster application on the application surface or between +10°C and +25°C in moisture free conditions.
ceramic tiling works should be performed 3 days later. - The torn and opened products should be closed
- To obtain the recommended long term technical immediately and consumed first.
performance of the product, after the completion of the all - Maximum 8 bags should be stocked on each other.
application, the application and/or work should be covered - Shelf life is maximum 6 months conditional to complying
and protected with a suitable coating or covering (plaster, with the above mentioned storage conditions.
screed, ceramic, tile etc…) as early as possible (depending on
the product’s drying time within 3-7 days).

2K
A B
max. 6 mm

5 1 12
30

28 Bostik Build Catalogue

CemenTech
C2 Duo
Two-Component Crystallized Waterproofing Mortar

Product description
It is cement based, two- component, brush consistency,
red colored cementitious compound and white colored
liquid emulsion sealing slurry that is reinforced by polymeric
additives, and that is used in the solution of problems arising
from capillary effects. It is used in both positive and negative
side of waterproofing of garages, terraces, foundations and
basements. CemenTech C2 Duo creates crystals that don’t
melt within water when it reacts with water and renders the
concrete water-tight permanently upon penetration of these
crystals into the capillary vessels of the concrete.
Application areas
- Both in positive and negative sides,
- On walls, grounds or ceilings,
- In continuously wet, humid and damp areas such as garage,
balcony, terrace and cellar,
- Water tanks, pools, reservoirs and storage tanks,
- In foundations, external walls of cellars, underground and
surface construction works,
- In amelioration, restoration and renovation works of old
structures
Features
- Reinforced with polymeric additives.
- Produces crystals that do not melt in water when reacted
with water.
- Resistant to heavy weather conditions.
- Features hydraulic adhesion quality.
- Used in any kind of bonded and plastered surface such as TECHNICAL DATA
stone and stone-derivative brick, pumice brick, briquette,
aerated concrete, limestone, etc. Color Light red
- Prevents wetness and water accumulation on cement-based Applicable Thickness (mm) Max 5
plastered surfaces.
- Prevents humidity and moisture permanently and eliminates Recommended applicable thickness 2 mm
unpressurized and weak water leakages.
- Protects surfaces against destructive effects of humidity Dry Unit Volume Weight (kg / lt) 1,3 ± 0,2
and moisture.
- Inflammable. Wet Unit Volume Weight (kg / lt) 1,8 ± 0,2
Preparation of the substrate Waiting Time in Container (min) ~ 30
- The surfaces to be coated should be free of adhesive
preventive foreign substances such as dust, dirt, mould Drying Time (hour) ~ 24
oil, paint etc.; residues and wastes like cement, plaster and
concrete should also be removed. Adhesion Strength (28 days) ≥ 1,5 (N / m m²)
- The sub-surfaces that are not strong enough to carry
themselves e.g. cracked plasters, weak surfaces, or residues Special mixture emulsion amount 9 kg (white colored liquid
of moss should be cleaned from the application surface. (for 25 kg dry powder component) emulsion)
- Surface should be slightly dampened before application.
- Active water leakages should be clogged before application Application temperature Between +5°C and +35°C
with Bostik CemenTech X.
Resistance of hardened coating Between -25°C and +80°C
Application
- Powder form Bostik CemenTech C2 Duo Waterproofing Technical data are approximately provided according to a temperature
Mortar should be poured slowly on liquid component (9 kg) of +23°C and a relative humidity of 50%.
that has been put into a clean container and should be mixed
by means of a mixer with low cycle until a cluster-free mixture
is obtained. Mixture duration should be minimum 5 minutes. - To obtain the recommended long term technical
The mixture obtained at the end of the process should performance of the product, after the completion of the all
be rested for 3 minutes and mixed again until it becomes application, the application and/or work should be covered
homogenous for 2 minutes. and protected with a suitable coating or covering (plaster,
- Bostik CemenTeach C2 Duo Waterproofing Mortar emulsion screed, ceramic, tile etc…) as early as possible (depending on
should be shaken well before use. the product’s drying time within 3-7 days).
- Application should be at least two layers thick. After
applying the first layer, at least 4-6 hours should be rested and Coverage
second layer should be applied before waiting period exceeds Approximately 1,5 – 2,0 kg/m² per each 1 mm thickness.
24 hours. Coverage amounts are theoretical values and it is
- The cracks that might be formed in the event of application recommended that coverage-controlled sample application is
to very wide surfaces should be prevented by means of carried out before application.
application by leaving joints. Joints should be filled with
flexible filling material. Package
- On the moving grounds that have cracking risk, Bostik Powder component in 25 kg craft bag, 64 sets in 1 palette
FlexMesh net can be applied as an intermediate layer between Liquid component in 9 kg plastic drum.
the application with the aim of forming a water isolation layer
which is more flexible in order to cover the tensile stress. Storage
- It shouldn‘t be applied to hot or frozen surfaces directly. - Dry mortar bags should be protected for water, frost and
adverse weather conditions.
Application with machine: - They should be kept dry and cool on wooden pallets at
CemenTech C2 Duo is suitable for use with sprayable machine. between +10°C and +25°C in moisture free conditions.
- The torn and opened products should be closed immediately
Waterproofing

Consult Bostik Technical Service for machine use.

and consumed first.
After application - Maximum 8 bags should be stocked on each other.
- Freshly applied surfaces should be protected against direct - Shelf life is maximum 12 months conditional to complying
sun light, strong air stream, high air temperature (above with the above mentioned storage conditions.
+35°C), rain and frost in the initial days (at least 5 days).
- Any kind of plaster application on the application surface or
ceramic tiling works, etc. works should be performed 3 days
later.

2K
A B
max. 2 mm

5 1 30
12

Bostik Build Catalogue 29

 CemenTech X
Water Plug

Product description
It is a cement-based, one-component, fast-curing, water-
plugging mortar that is reinforced with polymeric additives
and used to solve waterproofing problems that stem from
capillary effects, stop active water leakages before applying
waterproofing materials formulated for utilization from the
negative side in, foundations and basements.

Application areas
- On walls and floors,
- In continuously wet, humid and damp areas
- Water tanks, pools, reservoirs and storage tanks,
- In foundations, internal walls of basements,
- In underground and surface construction works,
- In amelioration, restoration and renovation works of old
structures,
- In any kind of bonded and plastered surface such as stone
and stone-derivative brick, pumice brick, briquette, aerated
concrete, limestone, etc.

Features
- Reinforced with polymeric additives.
- Allows fast application by drying very fast.
- Immediately stops the leakage which stems from negative
side and prevents insulation works.
- Resistant to heavy weather conditions. TECHNICAL DATA
- Hydraulic cementing quality.
- Prevents wetness and water accumulation on cement- Color Grey
based plastered surfaces.
- Prevents humidity and moisture permanently and Dry Unit Volume Weight (kg / lt) 1,5 ± 0,2
eliminates unpressurized and weak water leakages.
Wet Unit Volume Weight (kg / lt) 1,6 ± 0,2
- Protects surfaces against destructive effects of humidity
and moisture. Compressive Strength (28 days) ≥ 80 N / mm²
- Inflammable.
Bending Strength (28 days) ≥ 10 N / mm²
Preparation of the substrate
- The surfaces to be coated should be free of adhesive Mixing water amount (for 1 kg dry
0,2 – 0,3 lt
preventive foreign substances such as dust, dirt, mould mortar)
oil, paint etc.; residues and wastes like cement, plaster and Application temperature Between +5°C and +35°C
concrete should also be removed.
- The sub-surfaces that are not strong enough to carry Resistance of hardened coating Between -25°C and +80°C
themselves e.g. cracked plasters, weak surfaces, or residues
of moss should be cleaned from the application surface. Technical data are approximately provided according to a temperature
- Surface should be slightly dampened before application. of +23°C and a relative humidity of 50%.

Application
- Powder form Bostik CemenTech X Plugging Mortar should Storage
be poured slowly into a clean container filled with water - Dry mortar buckets should be protected for water, frost
in suitable ambiance temperature, and should be mixed by and adverse weather conditions.
means of a mixer with low cycle until a cluster-free mixture - They should be kept dry and cool.
is obtained. - The opened buckets should be closed immediately and
- The mortar is pressed onto the area of leakage manually and consumed first.
ensured it is frozen. - Maximum 8 bags should be stocked on each other.
- Gloves needs to be worn during the application. - Shelf life is maximum12 months conditional to complying
- The mortar applied on the leakage can be leveled with a with the above mentioned storage conditions.
spatula or steel trowel just before it is frozen.
- The mortar that is freshly prepared with Bostik CemenTech
X Plugging Mortar should be used within 3 minutes at the
latest.

After application
- Freshly applied surfaces should be protected against direct
sun light, strong air stream, high air temperature (above
+35°C), rain and frost in the initial days.
- Any kind of plaster application on the application surface or
ceramic tiling works should be performed 3 days later.

Coverage
Approximately 1,5 – 2,0 kg of powder per each 1 lt of gaps.

Package
Waterproofing

5 kg plastic buckets.

+5 ~ +35°C

1 1 3
2

30 Bostik Build Catalogue

 Application - CemenTech

STEP:1 STEP:2 STEP:3

The soundness of the substrates should be Swollen, aked-off, loose substrates Before the waterproo ng applications;
checked prior to waterproo ng applications. and old waterproo ng materials should shift rod, rod clearance, wooden wedge,
No application should be performed on the be removed from the surface before pipe and cable surroundings should be
substrates that are not strong enough to applying the waterproo ng materials. lled and repaired with special repair
bear their own weight. Swolen, aked-off, mortars.
loose substrates and old damaged layers
should be removed from the surface before
before waterproofing application.

STEP:4 STEP:5 STEP:6

Before the waterproo ng applications; Before the waterproo ng applications; Cement-based Bostik CemenTech
joint gaps should be opened at the the products should be stirred with a range products should be used for the
horizontal-vertical connection points low-cycle mixer for about 5 minutes insulation of wet areas such as water tanks,
swimming pools, bathrooms, toilets, etc.
or horizontal-vertical corners, concrete until a smooth mixture is obtained.
and for waterproo ng applications from
connections. The opened gaps should be negative side. Bostik CemenTech products
repaired and levelled with special repair should be applied on the surfaces with
mortars. ready substructure with a brush, roller or
trowel.
Waterproofing

STEP:7 STEP:8 STEP:9

Ready to use, easy to apply Bostik Bituminous Bostik AquaRoll B1 or After waiting for drying sufficient
AquaRoll Easy and Saniter products can BC2 should be preferred for the after all waterproofing applications,
be used safely on terrace and balcony protection of underground structures the surfaces should be covered with a
insulation. Bostik CemenTech products and waterproo ng applications in the covering material as desired.
should be applied on the surfaces with foundation. Bostik AquaRoll B1 and
ready substructure with a brush or BC2 products should be applied on the
roller. surfaces with ready substructure with a
brush or roller.

Bostik Build Catalogue 31

 BoscoMix P152
Crystallized Admix

Product Description
Bostik BoscoMix P152 is a new generation “A³ Technology”
enhanced, grey-colored, permanently active, integral
crystalline permeability reducing powdered admixture for
concrete works.
It is ideal for use in all type of concrete works and creates a
long term durable waterproof concrete.
Application Areas
- Foundations and basements and base-slabs
- Blind-side or single-face concrete works
- Precast concrete
- Manholes
- Underground vaults
- Parking structures
- Water containment structures
- Waste treatment facilities
- Marine structures
- Dams, water reservoirs and swimming pools
- Tunnels and subways
- Elevator pits
- Complex architectural design
Features
- Everlasting permanent integral solution
- Self-healing, crack bridging capability
- A³ Technology enhanced
- Excellent water vapor permeability
- Easy to use and save time
- It has no major site effect to the concrete Technical information
- It contains non-toxic, inorganic ions which provides a
durable concrete with high hydrostatic pressure resistance Color Grey
and resistance to water borne salts, chloride ion & sulfate
(chemical resistant to pH 3 ~ 11 constant contact) Bulk Density 0,95 ±0.05 kg / lt
- It also protects reinforcement against corrosion.
pH Value – slurry > 10
Dosage
Usual recommended typical dosage rate for Bostik BoscoMix Tested for 7 days after 7days
P152 is 1,0 % ~ 1,5 % by weight of total cementitious materials curing: Test mix ≤ 50% by
inside the fresh concrete mix mass of control mix
The dosage should not exceed 2,0 % by weight of cement Capillary Absorption (EN 480-5)
Tested for 28 days after 90
content for appropriate dosage rates for the specific projects days curing : Test mix ≤ 60%
please contact Bostik Technical Service
by mass of control mix
Application Instruction
Bostik BoscoMix P152 should be added at the time of mix Compressive strength At 28 days: Test mix ≥ 85 % of
batching stage of the ready-mix concrete at concrete plant. (EN 12390-3) Control mix

A.Dry-Batch Operations at Ready-Mix Concrete Plant Water Permeability (DIN 1048-5) < 20 mm
(recommended):
Add BoscoMix P152 in its original powder form to the vessel Water Soluble Chloride Content
< % 0,2
of the ready-mix concrete and preferably should be mixed (EN 480-10)
initially with the dry components of concrete mix as an
aggregate. To obtain a homogenous mixture, mix the dry V.O.C. %0
components for a minimum 5 minutes that the admix has
been thoroughly well dispersed throughout the concrete Technical data are approximately provided according to a temperature
mix. In all cases total quantity of water should be added in the of +23°C and a relative humidity of 50%.
design concrete mix in accordance with standard practices.
BoscoMix P152 should not be added to the ready-mix verified to confirm accordance with project specifications.
concrete after the cementitious components have been Please refer to product instructions or contact Bostik
added to the batch mix. Technical Service
B. Site-Mix Slurry Operations at Job-Site: - Bostik, is not responsible or liable under any circumstances
BoscoMix P152 should be mixed with a certain amount of for determining the merchantability or suitability of the
clean water to obtain a slurry (water mixing ratio , 1 part Bostik BoscoMix P152 or compatibility with the other Bostik
BoscoMix P152 : 2 part water). For a proper slurry mix the and/or any other supplier products for the customer’s
admix with clean water minimum 5 minutes. Then pour the intended purpose
admix slurry into the vessel of ready-mix concrete truck - Customer shall determine the suitability of the Bostik
properly and drive the vessel in high speed cycle minimum 10 BoscoMix P152 for the intended use and assume all risks and
minutes before placing the ready-mix concrete. liability in connection therewith representatives, to make any
In all cases total quantity of water should be added in the statements, which may supersede, modify or supplement
design concrete mix in accordance with standard practices. the information provided on its printed literature or package
Mixed fresh concrete should be placed within 20 minutes. labels without written confirmation from the Bostik
Please Note : It is important to obtain a well dispersed , Management.
homogenous mixture of ready-mix concrete with BoscoMix - All information provided by Bostik concerning Bostik
P152. Therefore, it is not recommended to add dry BoscoMix BoscoMix P152, including but not limited to, any
P152 in its original powder form directly to fresh concrete as recommendations and advice relating to the application
a dry-shake method. and use of Bostik BoscoMix P152, is given in good faith
based on Bostik’s current experience and knowledge of its
products when properly stored, handled and applied under
Limitations : normal conditions in accordance with Bostik ‘s application
- BoscoMix P152 is only for professional use
Waterproofing

instructions and data sheets.

- Allow at least 48 hours to cure before opening to foot
traffic Precautions:
- Protect fresh concrete against quick drying out The cement in concrete mix should comply with EN 197-1.
- For fully activation, the concrete structure may require 2-4 Be sure that “water/cement” ratio in concrete mix < 0,50.
weeks Mixed fresh concrete should be used within 20 minutes.
- Do not apply to dry surfaces When incorporating Bostik BoscoMix P152, the temperature
- Bostik BoscoMix P152 can be used as an invidual admixture of the concrete mix should be above 5ºC. The concrete mix
or in combination with other admixtures. In this case the containing Bostik BoscoMix P152 must be produced, placed
performance of the actual concrete mix design should be and finished same way as normal concrete according to
+5 ~ +35°C

7
Lt 1

32 Bostik Build Catalogue

valid governmental regulations, building codes and building
industry standard practices.
Depending on weather conditions, the use of water reducers,
superplasticizers, retarders and/or accelerating admixtures
may be necessary to maintain desired workability. It is
recommended to perform compatibility tests with other
admixtures as required.
Please note: Trial mixes under project conditions to
determine setting time, slump, air content and compressive
strength of concrete are highly recommended.
Packaging
20 kg craft bag, 66 bags in 1 palette (1320 kg/palette)
Storage and Shelf Life
The product should be stored in the original package in a cool,
dry place and out of direct sunlight (5°C – 30°C). Do not allow
product to freeze.
When stored in a dry place in unopened, undamaged original
packaging, shelf life is 6 months.
Caution
Irritant. May cause respiratory irritation. May cause an allergic
skin reaction. Do not get in eyes, on skin or on clothing. Do
not breathe fumes. Do not swallow. Use with adequate
ventilation. Wear protective clothing during dosing. Wash
thoroughly after usage.
First Aid Treatment
If in eyes or on skin, rinse with water for at least 15 minutes.
If breathed in, move person to fresh air. If swallowed, call a
Poison Control Center or doctor immediately. Do not induce
vomiting. Keep out of the reach of children

m
,3 m
x0
ma
Waterproofing

0,3 mm - Static capillary

cracks bridge

Bostik Build Catalogue 33

 It is time for new
BoscoPur Flat Roof Waterproofing Systems

- 2 in 1 system solution:
waterproofing and weatherproofing,
- Durable,
- UV stable,
- Non chalking and yellowing,
- Wear resistant,
- Resistant to pedestrian, light-weight
and heavy-duty traffic,
- Resistant to root penetration,
- Suitable for green roofing,
plantery systems,
- Water vapour permeable,
- Highly flexible (> 800 %),
- Ready to use,
- Easy to apply,
- Tested and approved by EOTA,
has an European Technical Approval
(ETA, Nr 13/0770).

34 Bostik Build Catalogue

BoscoPur
UniSeal
Polyurethane-Based Liquid Waterproofing Membrane

Product Description
Bostik BoscoPur UniSeal is a one-component, ready to use,
highly elastic, cold applied polyurethane waterproofing
membrane as a basecoat with excellent mechanical and
chemical, thermal, UV resistance.
Areas of applications
- Roofing
- Green roofing, flowerbeds, planter boxes
- Parking and bridge decks
- Balconies, terraces
Features
- Easy and fast application
- Provides a seamless waterproofing membrane
- Highly resistant to abrasion, water and root penetration
- Unaffected by weather conditions. Provides excellent
weather and UV resistance
- Water vapour permeable
- Very good abrasion resistance and suitable for walkways,
pedestrian traffic and heavy duty areas
- Crack bridging capability up to 2 mm
- Provides excellent thermal resistance over a temperature
span of – 30 ºC to + 90 ºC
- Resistant to salty water, aqueous solution, bases, diluted
acids, aliphatic solvents, benzene and mineral oils
- Impregnates by penetrating deeply into all mineral and
concrete surfaces with high adherence
- Fills the non-structural capillary cracks by decreasing water-
absorbency of the concrete construction TECHNICAL DATA
- Hardens the upper surface of the concrete by deeply
penetrating into the surfaces Colour Grey
Application Tensile Strenght > 4 N / mm²
- After the priming Bostik BoscoPur UniSeal has be to be applied
in a short period of time as a basecoat. Elonagation @ Break > 900 %
- After priming with BoscoPur PurPrimer 1C onto porous
substrates, BoscoPur UniSeal has to be applied within 2-3 hours Crack Bridging Capability Up to 2 mm
(not later than 4 hours) when the primer is still a little bit tacky.
- After priming with BoscoPur EpoPrimer 2C onto non-porous Water Vapour Permeability > 25 gr / m² / day
substrates, BoscoPur UniSeal has to be applied within 6-12
hours (not later than 24 hours) when the primer is still a little bit Shore A Hardness > 60
tacky.
- Bostik BoscoPur UniSeal has to be stirred well with an Resistance to water pressure No leak (1m water column, 24h)
electrical mixer before the application.
- When the product becomes homogenous apply the product > 2,0 N/mm² (concrete surface
with a brush or roller until the surface is fully covered. Adhesion to concrete
- 2nd coat has to be applied within 18 hours (not later than 48 failure)
hours)
- As an option, I can also be applied by an airless spray. Shock temperature (20 min) 200 °C
- Wall-Floor connections, pipes, siphons etc… has to be
fully reinforced with Bostik BoscoPur Fabric. For this kind Curing time (h) 12 - 24 (Conditions: 20°C, 50% RH)
of application, apply the 1st coat BoscoPur UniSeal and then
embed the BoscoPur Fabric and immediately apply the 2nd coat Application temperature Between +10°C and +35°C
BoscoPur UniSeal as wet on wet. For these kind of detailings Resistance of hardened
Bostik BoscoPur PowerFiber can also be used. Between -30°C and +90°C
coating
After application
Newly applied surfaces should be protected from water min for Technical data are approximately provided according to a temperature
4 hours of +23°C and a relative humidity of 50%.
For the long lasting UV stability, abrasion resistance againts
traffic and to avoid the chaulking and surface yellowing, an UV - Maximum 3 buckets should be stocked on each other.
resistant top-coats Bostik BoscoPur Top - HT is recommended. - Shelf life is maximum 9 months conditional to complying with
The non-cured, fresh Bostik BoscoPur UniSeal is slippery when the above mentioned storage conditions.
wet or during rain. In order to get an anti-slip surface dry quarz
sand can be sprinkled during curing period of the membrane
Warning
For the best results, do not apply the Bostik BoscoPur UniSeal
over 0,5 mm dry film thickness per layer. Low temperature
retards the curing process and high temperature accelerates
the curing process.
Coverage
Approx. 0,750 – 1,25 kg / m² per layer depending on the
absorbency and smoothness of the surface.
The coverage amounts are theoretical and it is recommended to
do coverage-controlled sample application before treatment.
Packaging
25 kg metal can
Waterproofing

Storage
- They should be protected for water, frost and adverse
weather conditions.
- They should be kept dry and cool on wooden pallets at
between +10°C and +25°C in moisture free conditions.
- The opened products should be closed immediately and
consumed first.

+5 ~ +35°C

1/2 6

Bostik Build Catalogue 35

 BoscoPur
PowerFiber
Polyurethane-Based Patching and Detailing Membrane

Product Description
Bostik BoscoPur PowerFiber is a one-component, ready to
use, highly elastic, tixotropic, fiber reinforced, light grey
coloured, polyurethane waterproofing membrane with
excellent mechanical and chemical, thermal, UV resistance.
Areas of applications
- For detailing and patching of the wall-floor connections,
flashings and 90° angles,
- Around lightdomes and rooflights,
- Chimneys and pipes,
- HVAC units, photovoltaic systems,
- Siphons, gutters, etc.
Features
- Easy and fast application.
- Provides a seamless waterproofing membrane.
- Highly resistant to abrasion, water and root penetration.
- Unaffected by weather conditions.
- Water vapour permeable.
- Suitable for repairing of the old bituminous membranes and
asphalt felts.
- Resistant to salty water, aqueous solution, bases, diluted
acids, aliphatic solvents, benzene and mineral oils.
- Impregnates by penetrating deeply into all mineral and
concrete surfaces with high adherence.
- Fills the non-structural capillary cracks by decreasing
water-absorbency of the concrete construction.
- Hardens the upper surface of the concrete by deeply TECHNICAL DATA
penetrating into the surfaces.
- Forms an impermeable surface by filling the pores in the Colour Light grey
surfaces like aerated concrete.
Curing time (h) 12 - 24
Coverage
Approx. 1,00 kg / m² depending on the absorbency and Application temperature Between +10°C and +35°C
smoothness of the surface.
The coverage amounts are theoretical and it is recommended Resistance of hardened coating Between -30°C and +90°C
to do coverage-controlled sample application before
treatment. Technical data are approximately provided according to a temperature
of +23°C and a relative humidity of 50%.
Packaging
6 kg metal can between +10°C and +25°C in moisture free conditions.
Storage - The opened products should be closed immediately and
- They should be protected for water, frost and adverse consumed first.
weather conditions. - Maximum 3 buckets should be stocked on each other.
- They should be kept dry and cool on wooden pallets at - Shelf life is maximum 9 months conditional to complying
with the above mentioned storage conditions.

BoscoPur
Fabric
Textile Reinforcement

Product Description
Bostik BoscoPur Fabric, is a polyester textile reinforcement
which is used for strengthen BoscoPur waterproofing system
mechanically.

Application
- For BoscoPur Fabric application; apply the 1st coat BoscoPur
UniSeal and then embed the BoscoPur Fabric and immediately
apply the 2nd coat BoscoPur UniSeal as wet on wet. TECHNICAL DATA
- It is recommended to apply 3nd coat BoscoPur Uniseal Weight (g/m²) 63
where necessary further to a smooth surface ( to make sure
Waterproofing

the surface is completely covered) Thickness (mm) 0,7

Packaging Tensile strength (N/5cm) 125

100 m² / roll
Elongation (longitudinal) %77
Elongation (lateral) %83

36 Bostik Build Catalogue

BoscoPur
Top – HT
Polyurethane-Based Liquid Waterproofing Top-coating Membrane

Product Description
Bostik BoscoPur Top – HT is a one-component, ready to use,
elastic, semi-rigid, wear resistant, cold applied, aliphatic
polyurethane waterproofing top-coating membrane with
excellent mechanical and chemical, thermal, UV resistance.

Areas of applications
- Roofing,
- Balconies, terraces,
- Pedestrian decks and walkways,
- Heavy duty areas (parking decks, industrial areas, malls,
stadiums etc…)

Features
- Easy and fast application.
- Provides a seamless waterproofing membrane.
- Highly resistant to abrasion, water and root penetration.
- Unaffected by weather conditions. Provides excellent
weather and UV resistance.
- UV and colour stable.
- Provides “easy to clean” surface.
- Water vapour permeable.
- Very good abrasion resistance and suitable for walkways,
pedestrian traffic, heavy duty areas, industrial areas.
- Crack bridging capability up to 2 mm.
- Provides excellent thermal resistance over a temperature TECHNICAL DATA
span of – 30 ºC to + 90 ºC.
- Resistant to salty water, aqueous solution, bases, diluted Colour Grey
acids, aliphatic solvents, benzene and mineral oils.
- Impregnates by penetrating deeply into all mineral and Tensile Strenght > 5 N / mm²
concrete surfaces with high adherence.
Elonagation @ Break > 100 %
- Fills the non-structural capillary cracks by decreasing
water-absorbency of the concrete construction. Water Vapour Permeability > 6 gr / m² / day
- Hardens the upper surface of the concrete by deeply
penetrating into the surfaces. Shore D Hardness > 30

Preparing the substrate Curing time (h) 12 - 24

- The dehumidified surfaces should be stable, binding, clean Application temperature Between +10°C and +35°C
and grease-free.
- Maximum moisture content should not exceed 5%. Resistance of hardened coating Between -30°C and +90°C
Substrate compressive strength should be at least 25MPa,
New concrete structures need to dry for at least 28 days Technical data are approximately provided according to a temperature
- The surfaces with bitumen, acrylic and tar and the non- of +23°C and a relative humidity of 50%.
porous or glazed surfaces such as metal, ceramic tiles, old
coatings should be cleaned until no residues remain then Warning
primed with the BoscoPur EpoPrimer 2C before application. For the best results, do not apply the Bostik BoscoPur Top -
- Porous and absorbent substrates such as wood, concrete, HT over 0,2 mm dry film thickness per layer. Low temperature
plaster… should be primed with the BoscoPur PurPrimer 1C retards the curing process and high temperature accelerates
before application. the curing process.
- After the priming Bostik BoscoPur UniSeal has be to be
applied in a short period of time as a basecoat. Coverage
Approx. 0,250 kg / m² per layer depending on the absorbency
Application and smoothness of the surface.
- After the Bostik BoscoPur UniSeal, Bostik BoscoPur Top – HT The coverage amounts are theoretical and it is recommended
has be to be applied in a short period of time as a topcoat (not to do coverage-controlled sample application before
later than 36 hours) treatment.
- Bostik BoscoPur Top – HT has to be stirred well with an
electrical mixer before the application. Packaging
- When the product becomes homogenous apply the product 20 kg metal can
with a brush or roller until the surface is fully covered.
- Optional, if a 2nd coat is needed, it has to be applied within Storage
3 – 6 hours (not later than 36 hours) - They should be protected for water, frost and adverse
- The Bostik BoscoPur – HT must always be used over Bostik weather conditions.
BoscoPur UniSeal which was previously sprinkled with oven - They should be kept dry and cool on wooden pallets at
dry silica sand that creates an adhesion bridge between the between +10°C and +25°C in moisture free conditions.
layers. - The opened products should be closed immediately and
- As an option, I can also be applied by an airless spray. consumed first.
- Maximum 3 buckets should be stocked on each other.
After applicatioN - Shelf life is maximum 9 months conditional to complying
Newly applied surfaces should be protected from water min with the above mentioned storage conditions.
for 4 hours
Waterproofing

The Bostik BoscoPur Top - HT is slippery when or during rain.

In order to get an anti-slip surface dry quarz sand can be
sprinkled during curing period of the membrane

+5 ~ +35°C
1

Bostik Build Catalogue 37

 BoscoPur
PurPrimer 1C
Polyurethane-Based Primer for Porous Substrates

Product Description
Bostik BoscoPur PurPrimer 1C is a one-component, ready
to use, transparent, deeply penetrating and rapid curing
polyurethane priming material with solvent content. It is
used as a primer before applying the polyurethane-based
materials onto porous and absorbent substrates.

Areas of applications
To increase the adhesion performance of mineral-based
surfaces

Features
- Easy and fast application
- Contains solvent
- Unaffected by weather conditions
- Resistant to salty water, aqueous solution, bases, diluted
acids, aliphatic solvents, benzene and mineral oils
- Impregnates by penetrating deeply into all mineral and
concrete surfaces with high adherence
- Hardens the upper surface of the concrete by deeply
penetrating into the surfaces
- Forms an impermeable surface by filling the pores in the
surfaces like aerated concrete

Preparing the substrate

- The dehumidified surfaces should be stable, binding, clean TECHNICAL DATA
and grease-free.
- Maximum moisture content should not exceed 5%. Colour Transparent
Substrate compressive strength should be at least 25MPa,
New concrete structures need to dry for at least 28 days Adhesion to concrete > 1,8 N / mm² (concrete failure)
- The surfaces with bitumen, acrylic and tar should be
Shore A hardness > 95
cleaned until no residues remain and they should be ready
before application. Curing time (h) 2–3

Application Application temperature Between +5°C and +35°C

- Bostik BoscoPur PurPrimer 1C can be applied by roller or
brush, until the surface is covered. Resistance of hardened coating Between -30°C and +90°C
- As an option, I can also be applied by an airless spray. Technical data are approximately provided according to a temperature
of +23°C and a relative humidity of 50%.
After applicatioN
Newly applied surfaces should be protected from water for
2 - 3 hours and the basecoat has to be applied within 2-3
hours (not later than 4 hours)

Coverage
Approx. 0,200 kg / m² per layer depending on the absorbency
and smoothness of the surface.
The coverage amounts are theoretical and it is recommended
to do coverage-controlled sample application before
treatment.

Packaging
15 kg metal can

Storage
- They should be protected for water, frost and adverse
weather conditions.
- They should be kept dry and cool on wooden pallets at
between +10°C and +25°C in moisture free conditions.
- The opened products should be closed immediately and
consumed first.
- Maximum 3 buckets should be stocked on each other.
- Shelf life is maximum 9 months conditional to complying
with the above mentioned storage conditions.
Waterproofing

+5 ~ +35°C

1/2 2

38 Bostik Build Catalogue

BoscoPur
EpoPrimer 2C
Water-Borned Epoxy-Based Primer for Porous Substrates

Product DescriptioN
Bostik BoscoPur EpoPrimer 2C is a two-component, rigid,
water-borned epoxy based universal primer in transparent
colour. It is used as a primer before applying the polyurethane
or epoxy based materials onto porous and absorbent
substrates.

Areas of applications
- To prime the dusting and crumbling surfaces
- To increase the adhesion performance of mineral-based
surfaces
- Glass, tiles, ceramics, bituminous membranes, metal and
aluminium
- Used for obtaining high adherence in surfaces to be coated
polyurethane or epoxy

Features
- Easy and fast application
- Can also be applied on moist surfaces, without loss of
adhesion.
- Can be diluted with water.
- Highly resistant to abrasion and water
- Unaffected by weather conditions
- Resistant to salty water, aqueous solution, bases, diluted
acids, aliphatic solvents, benzene and mineral oils
- Impregnates by penetrating deeply into all mineral and TECHNICAL DATA
concrete surfaces with high adherence
- Fills the non-structural capillary cracks by decreasing Colour Transparent
water-absorbency of the concrete construction
- Hardens the upper surface of the concrete by deeply Mixing Ratio 3:1
penetrating into the surfaces
Curing time (h) 6 - 12
- Forms an impermeable surface by filling the pores in the
surfaces like aerated concrete Pot Life (h) Max 1

Preparing the substrate Application temperature Between +10°C and +35°C

- The dehumidified surfaces should be stable, binding, clean
and grease-free. Resistance of hardened coating Between -30°C and +90°C
- Maximum moisture content should not exceed 8 %. Technical data are approximately provided according to a temperature
Substrate compressive strength should be at least 25 MPa, of +23°C and a relative humidity of 50%.
New concrete structures need to dry for at least 28 days
- The surfaces with bitumen, acrylic and tar should be
cleaned until no residues remain and they should be ready Storage
before application. - They should be protected for water, frost and adverse
- It increases the adherence of the add-on material when weather conditions.
applied before adhesive or coating materials, such as wood, - They should be kept dry and cool on wooden pallets at
concrete on the absorbent surfaces. between +10°C and +25°C in moisture free conditions.
- The opened products should be closed immediately and
Application consumed first.
- Bostik BoscoPur EpoPrimer 2C ‘s comp. A and comp. B - Maximum 3 pails should be stocked on each other.
should be mixed by low speed mechanical mixer according to Shelf life is maximum 9 months conditional to complying
the stipulated mixing ratio, for about 3-5 min. with the above mentioned storage conditions.
- The mixing of the components has to be effected very
thoroughly, especially on the walls and bottom of the pail
until the mixture becomes fully homogeneous.
- To regulate the consistency the mixture can be diluted with
25 % of clean water
- Bostik BoscoPur EpoPrimer 2C can be applied by roller or
brush, until the surface is covered.

After application
Newly applied surfaces should be protected from water for
2 – 3 hours and the basecoat has to be applied within 6 6- 12
hours (not later than 24 hours)

Coverage
Approx. 0,150 kg / m² per layer, depending on the absorbency
and smoothness of the surface.
The coverage amounts are theoretical and it is recommended
to do coverage-controlled sample application before
treatment.
Waterproofing

Packaging
(12+4) kg /set

+5 ~ +35°C
2K
A B

1/2 6

Bostik Build Catalogue 39

 BoscoPur
GreenSeal
E.F.P. Polyurethane-Based Liquid Waterproofing Membrane

Product Description
Bostik BoscoPur GreenSeal is an one-component, ready to
use, highly permanent elastic, cold applied polyurethane
waterproofing membrane which is developed with a unique
E.F.P. technology based on new generation of polyurethane.
BoscoPur GreenSeal is a primerless coating with excellent
mechanical and chemical, thermal, UV resistance used for
the waterproofing of exposed or non- exposed terraces and
balconies.

Areas of applications
- Flat roofing
- Balconies, terraces
- Wet areas (toilets, bathrooms, kitchens as an undertiling
membrane).

Features
- Easy and fast application
- Provides a seamless waterproofing membrane Resistant to
abrasion, water and heat & frost
- Unaffected by weather conditions. Provides excellent
weather and UV resistance
- Water vapour permeable
- Crack bridging capability up to 1 mm
- Provides excellent thermal resistance over a temperature
span of -20ºC to +80ºC
- Impregnates by penetrating deeply into all mineral and
concrete surfaces with high adherence Technical data
- Fills the non-structural capillary cracks by decreasing
water-absorbency of the concrete construction Colour Grey
- Hardens the upper surface of the concrete by deeply
penetrating into the surfaces Tensile Strenght > 1,5 N / mm²

Preparing the substrate Elonagation @ Break > 500 %

- The dehumidified surfaces should be stable, binding, clean Crack Bridging Capability Up to 1 mm
and grease-free.
- Maximum moisture content should not exceed 10 %. Water Vapour Permeability > 15 gr / m² / day
Substrate compressive strength should be at least 25MPa,
New concrete structures need to dry for at least 28 days Shore A Hardness > 60
- The surfaces with bitumen, tar should be cleaned until
no residues remain and then primed with the BoscoPur Curing time (h) 6 - 18
EpoPrimer 2C before application.
- Porous and absorbent substrates should be primed with the Application temperature Between +10°C and +35°C
BoscoPur GreenSeal (diluted up to ~ 20 % with clean water)
and the non-porous or glazed surfaces such as metal, ceramic Resistance of hardened coating Between -20°C and +80°C
tiles, old coatings should be primed with the BoscoPur Technical data are approximately provided according to a temperature
EpoPrimer 2C before application. of +23°C and a relative humidity of 50%.
Application
- Bostik BoscoPur GreenSeal has to be stirred well with an Warning
electrical mixer before the application. For the best results, do not apply the Bostik BoscoPur
- When the product becomes homogenous apply the product GreenSeal over 0,5 mm dry film thickness per layer.
with a brush or roller until the surface is fully covered. Low temperature retards the curing process and high
- After the priming Bostik BoscoPur GreenSeal has be to be temperature accelerates the curing process.
applied in a short period of time as a basecoat.
- After priming with Bostik BoscoPur GreenSeal itself Coverage
onto porous substrates, the non-diluted Bostik BoscoPur Approx. 0,500 ~ 0,600 kg / m² per layer depending on the
GreenSeal has to be applied within 6-12 hours (not later than absorbency and smoothness of the surface.
24 hours) as a 1st basecoat when the primer is still a little bit The coverage amounts are theoretical and it is recommended
tacky. to do coverage-controlled sample application before
- 2nd coat has to be applied within 12 hours (not later than 24 treatment.
hours)
- As an option, it can also be applied by an airless spray. Packaging
- Wall-Floor connections, pipes, siphons etc… has to be fully 25 kg metal can
reinforced with Bostik BoscoPur Fabric. For this kind of
application, apply the 1st coat BoscoPur GreenSeal and then Storage
embed the BoscoPur Fabric and immediately apply the 2nd - They should be protected for water, frost and adverse
coat BoscoPur GreenSeal as wet on wet. For these kind of weather conditions.
detailings Bostik BoscoPur PowerFiber can also be used. - They should be kept dry and cool on wooden pallets at
between +10°C and +25°C in moisture free conditions.
Application with machine - The opened products should be closed immediately and
BoscoPur GreenSeal is suitable for use with sprayable consumed first.
machine. Consult Bostik Technical Service for machine use. - Maximum 3 buckets should be stocked on each other.
- Shelf life is maximum 9 months conditional to complying
After application with the above mentioned storage conditions.
Waterproofing

Newly applied surfaces should be protected from water

min for 12 hours. For the long lasting UV stability, abrasion
resistance againts traffic and to avoid the chaulking and
surface yellowing, an UV resistant top-coat is recommended.
The non-cured, fresh Bostik BoscoPur GreenSeal is slippery
when wet or during rain. In order to get an anti-slip surface
dry quarz sand can be sprinkled during curing period of the
membrane.

+5 ~ +35°C
2K
A B

1/2

40 Bostik Build Catalogue

BoscoPur
BitumFlex
Polyurethane-Based, Bitumen Extended Waterproofing Membrane

Product Description
Bostik BoscoPur BitumFlex is a two-component (1:1), highly
elastic, cold applied, bitumen extended, rapid curing,
solvent-borned polyurethane waterproofing membrane with
excellent mechanical and chemical resistance.

Areas of applications
- Foundations,
- Retaining Walls,
- Green roofing, flowerbeds, planter boxes,
- Parking and bridge decks,
- Balconies, terraces, roofs (concieled).

Features
- Easy and fast application.
- Rapid curing.
- Provides a seamless waterproofing membrane.
- Crack bridging properties upto 2 mm.
- Highly resistant to water and root penetration.
- Provides excellent thermal resistance over a temperature
span of – 30 ºC to + 90 ºC.
- Resistant to salty water, aqueous solution, bases, diluted
acids and mineral oils.
- Impregnates by penetrating deeply into all mineral and
concrete surfaces with high adherence.
- Fills the non-structural capillary cracks by decreasing
water-absorbency of the concrete construction.
- Hardens the upper surface of the concrete by deeply TECHNICAL DATA
penetrating into the surfaces.
Colour Black
Preparing the substrate
- The dehumidified surfaces should be stable, binding, clean Density 0,99 g / cm³
and grease-free.
- Maximum moisture content should not exceed 5%. Viscosity (Brookfield) ~ 6650 cP
Substrate compressive strength should be at least 25MPa, Tensile Strenght > 7 N / mm²
New concrete structures need to dry for at least 28 days
- The surfaces with bitumen, acrylic and tar and the non- Adhesion to concrete (ASTM D 903) > 1,1 N / mm²
porous or glazed surfaces such as metal, ceramic tiles, old
coatings should be cleaned until no residues remain then Elonagation @ Break > 2500 %
primed with the BoscoPur EpoPrimer 2C before application.
- Porous and absorbent substrates such as wood, concrete, Crack Bridging Capability Up to 2 mm
plaster… should be primed with the BoscoPur PurPrimer 1C
before application. Tear Resistance (ASTM D 624) 20 N / mm

Application Shore A Hardness > 35

- After the priming Bostik BoscoPur BitumFlex has be to be Puncture Resistance 290 N
applied in a short period of time as a waterproofing coat.
- After priming with BoscoPur PurPrimer 1C onto porous Resistance to Hydrostatic pressure No Leak @ 3 bar (30 m
substrates, BoscoPur BitumFlex has to be applied within 2-3 (DIN 16726) water column)
hours (not later than 4 hours) when the primer is still a little
bit tacky. Max. Temperature short time 250°C (15min shock)
- After priming with BoscoPur EpoPrimer 2C onto non-
porous substrates, BoscoPur BitumFlex has to be applied Pot Life (min) 30 – 35
within 6-12 hours (not later than 24 hours) when the primer is
still a little bit tacky. Curing time (h) 12 - 24
- Bostik BoscoPur BitumFlex component A has to be stirred
well with an electrical mixer before the mixing with the Application temperature Between +10°C and +35°C
component B. Resistance of hardened coating Between -30°C and +90°C
- Then the 2 components (1:1 by volume) of Bostik BoscoPur
BitumFlex should be stirred well with an electrical mixer for 3 Technical data are approximately provided according to a temperature
min. until getting a homogenous mixture. of +23°C and a relative humidity of 50%.
- When the product becomes homogenous apply the product
with a brush or roller until the surface is fully covered.
- 2nd coat has to be applied within 12 - 24 hours (not later Coverage
than 72 hours) Approx. 0,750 lt / m² per layer depending on the absorbency
- As an option, it can also be applied by an airless spray. and smoothness of the surface.
- Wall-Floor connections, pipes, siphons etc… has to be fully The coverage amounts are theoretical and it is recommended
reinforced with Bostik BoscoPur Fabric. For this kind of to do coverage-controlled sample application before
application, apply the 1st coat BoscoPur BitumFlex and then treatment.
embed the BoscoPur Fabric and immediately apply the 2nd
coat BoscoPur BitumFlex as wet on wet. For these kind of Packaging
detailings Bostik BoscoPur PowerFiber can also be used. (20 lt + 20 lt) /metal bucket set

After application Storage

Newly applied surfaces should be protected from water min - They should be protected for water, frost and adverse
Waterproofing

for 4 hours weather conditions.

The Bostik BoscoPur BitumFlex is slippery when wet or - They should be kept dry and cool on wooden pallets at
during rain. In order to get an anti-slip surface dry quarz sand between +10°C and +25°C in moisture free conditions.
can be sprinkled during curing period of the membrane - The opened products should be closed immediately and
consumed first.
- Maximum 3 buckets should be stocked on each other.
- Shelf life is maximum 9 months conditional to complying
with the above mentioned storage conditions.

+5 ~ +35°C
2K
A B

1/2 6

Bostik Build Catalogue 41

 Application - BoscoPur System

STEP:1 STEP:2 STEP:3

The soundness of the substrates Maximum moisture content should not Porous and absorbent substrates such as
should be checked prior to BoscoPur exceed 5%. wood, concrete, plaster… should be primed
System waterproofing applications. No with the BoscoPur PurPrimer 1C before
application. The surfaces with bitumen,
application should be performed on the
acrylic and tar and the non-porous or
substrates that are not strongenough to glazed surfaces such as metal, ceramic
bear their own weight. tiles, old coatings should be cleaned until
no residues remain then primed with the
BoscoPur EpoPrimer 2C before application.

STEP:4 STEP:5 STEP:6

Wall-Floor connections, pipes, siphons After the priming Bostik BoscoPur BoscoPur Fabric mesh should be laid to
etc… has to be fully reinforced with UniSeal has be to be applied with rolls in adhere firmly to the surface without any
Bostik BoscoPur PowerFiber. a short period of time as a basecoat. pot. Additional space should be created
at least 5 cm overlay for.
Waterproofing

STEP:7 STEP:8

For this kind of application, apply the 1st Depending on the pedestrian traffic
coat BoscoPur UniSeal and then embed on the top coat of waterproofing
the BoscoPur Fabric and immediately membrane; such as exposure to heavy
apply the 2nd coat BoscoPur UniSeal as pedestrian traffic areas in BoscoPur
wet on wet. Where necessary, further
to a smooth surface (to make sure the Top-HT should be used.
surface is completely covered) making
3 rd coatsis recommended.

42 Bostik Build Catalogue

AquaRoll
PU Mono
Polyurethane-Based Waterproofing Coating

Product Description
Bostik AquaRoll PU Mono is a one-component, ready-to-use,
solvented polyurethane-based waterproofing material that is
applied as liquid. It cures by reaction with humidity, maintains
its elasticity and is suitable for use on the positive side only.

Areas of applications
- Exterior,
- In terraces, roof tops and balconies,
- In foundations and base shear walls,
- For the protection of concrete constructions from water
and corrosion,
- Used against water in the wood and metal sheet type
applications.

Features
- Easy to apply.
- Very good crack bridging properties.
- Highly resistant to UV and frost.
- Water vapour permeable.
- Excellent adherence.

Preparation of the substrate

- The surfaces to be coated should be free of adhesive
preventive foreign substances such as dust, dirt, mould
oil, paint etc.; residues and wastes like cement, plaster and TECHNICAL DATA
concrete should also be removed.
- The application surface should be dry, clean, stable, sound Colour White, grey
and bear burden.
- The substrates should not contain holes or cracks and Density (gr/cm³) 1,40 ± 0,2
should be dust-free.
Set to foot traffic (at 23°C) 16 – 24 h
- This kind of defects should be fixed with repair mortars
prior to application. Solid matter ratio ~ %90
- The surface which are ready for application should be
primed with Bostik AquaRoll PU Prim-PP or Bostik AquaRoll Shore A hardness (7 days) 65
PU Prim-MP and should be rested for minimum 3-4 hours and
maximum 48 hours. Tensile strength (DIN 53504) (7 days) ≥ 8 (N/mm²)
Elongation at break (DIN 53504) % 600 (7 days)
Application
- The material should be made ready for use by stirring with a Application temperature Between +5°C and +35°C
low-speed mixer.
- It is spread homogeneously on the substrates that are Serve temperature Between -25°C and +80°C
primed with a fine comb, trowel, short-bristle roller brush or
Technical data are approximately provided according to a temperature
a suitable sprayer.
of +23°C and a relative humidity of 50%.
- In case of second layer application, approximately 12 - 48
hours should be waited between two layers. Waiting time
shortens in hot weather and lengthens in cold weather. Storage
- They should be protected for water, frost and adverse
After application weather conditions.
In the first days, newly applied surfaces should be protected - They should be kept dry and cool on wooden pallets at
from direct sunlight, severe air stream, high temperatures between +10°C and +25°C in moisture free conditions.
(over +35°C), adverse air conditions such as rain and frost. - The opened products should be closed immediately and
consumed first.
Coverage - Maximum 3 buckets should be stocked on each other.
Approx. 0,750 – 0,850 kg / m² /mm depending on the - Shelf life is maximum 9 months conditional to complying
absorbency and smoothness of the surface. with the above mentioned storage conditions.
The coverage amounts are theoretical and it is recommended
to do coverage-controlled sample application before
treatment.

Packaging
25 kg metal can
Waterproofing

+5 ~ +35°C
2
max. 2 mm
24
1

Bostik Build Catalogue 43

 AquaRoll
PU Prim - PP
Polyurethane-Based Primer for Porous Substrates

Product Description
Bostik AquaRoll PUPrim - PP is a one-component, ready
to use, transparent polyurethane priming material with
solvent content. It is used as a primer before applying the
polyurethane-based materials onto porous and absorbent
substrates.

Areas of applications
To prime the dusting and crumbling surfaces; To increase
the abrasion resistance of mineral-based surfaces; Used
for obtaining high adherence in surfaces to be coated
polyurethane.

Features
Easy and fast application; Contains solvent; Highly
resistant to abrasion and water; Unaffected by weather
conditions; Resistant to salty water, aqueous solution,
bases, diluted acids, aliphatic solvents, benzene and mineral
oils; Impregnates by penetrating deeply into all mineral
and concrete surfaces with high adherence; Fills the non-
structural capillary cracks by decreasing water-absorbency
of the concrete construction; Hardens the upper surface
of the concrete by deeply penetrating into the surfaces;
Provides two-stage protection ensuring permanent
waterproofing on the surface; Forms an impermeable
surface by filling the pores in the surfaces like aerated TECHNICAL DATA
concrete.
Colour Transparent
Coverage
Approx. 0,150 kg / m² depending on the absorbency and Curing time (h) 3–8
smoothness of the surface. The coverage amounts are
Application temperature Between +5°C and +35°C
theoretical and it is recommended to do coverage-controlled
sample application before treatment. Resistance of hardened coating Between -25°C and +80°C

Packaging Technical data are approximately provided according to a temperature

15 kg tin. of +23°C and a relative humidity of 50%.

+5 ~ +35°C

1 12

AquaRoll
PU Prim – MP
Silane-Based Primer for Non-Porous, Glazed Substrates
Product Description
Bostik AquaRoll PUPrim - MP is a one-component, ready to
use, silane-based, transparent primer that is specifically
formulized for non-porous and non-absorbent surfaces. It
is suitable for polyurethane-based topcoats, joint filling and
surface coating materials.

Areas of applications
To prime non-dusting, non-absorbent, glazy substrates; To
prime non-absorbent substrates such as metal, ceramics,
marble, granite, massive-concrete, wood, fibreglass, etc.

Features
No film formation; Perfect adherence; Suitable for fresh-cut
Waterproofing

joints; Does not leave any stains or marks outside of the joint TECHNICAL DATA
applied; Easy to apply.
Colour Transparent
Coverage
Approx. 0,100 kg / m² depending on the absorbency and Density (gr/cm³) 0,87 ± 0,05
smoothness of the surface. Initial curing (min) 15
The coverage amounts are theoretical and it is recommended
to do coverage-controlled sample application before Waiting Time for the topcoat Max 24 hours
treatment.
Application temperature for application Between +5°C and +35°C
Packaging
Technical data are approximately provided according to a temperature
2,5 kg metal can
of +23°C and a relative humidity of 50%.

44 Bostik Build Catalogue

AquaRoll
Easy - UV
UV Resistant Liquid Membrane

Product Description
Bostik AquaRoll Easy UV, is a liquid-applied water
impermeable products for use beneath ceramic tiling bonded
with adhesive, solvent-free, ready-to-use, elastomeric
resin-based, white-coloured, UV resistant. It is produced in
accordance with TS EN 14891:2012 Class DM P resistant to
chlorinated water and used for protecting the buildings from
harmful effects of water. AquaRoll Easy UV is capable of
bridging crack and suitable for use on the positive side only.

Areas of applications
- Interior and exterior,
- In horizontal and vertical applications,
- In balconies and terraces.

Features
- Flexible after curing.
- Resistant to crack formations on the application surface;
seamless.
- UV resistant.
- Applicable with a brush; easy to apply.
- Suitable for use in all kinds of mineral-based surfaces, stone
and stone-derivative bricks, pumice brick, briquette, aerated
concrete, concrete block, limestone, etc. built plastered
surfaces, cement-based plastered surfaces, grout and
concrete surfaces. TECHNICAL DATA
Preparation of the substrate Colour White
- The surfaces to be coated should be free of adhesive
preventive foreign substances such as dust, dirt, mould Applicable thickness (mm) Max 2
oil, paint etc.; residues and wastes like cement, plaster and
Unit volume weight of the mixture 1,30 ± 0,2 (kg/lt)
concrete should also be removed.
- The sub-surfaces that are not strong enough to carry Viscosity (dPa s) 200,000 – 250,000
themselves e.g. cracked plasters, weak surfaces, or residues
of moss should be cleaned from the application surface. First drying time (h) 4
- The application surface must definitely be crack-free, stable
and strong. The gaps should be filled with Bostik 410 HP. Fully dry after (h) 24 - 48
- Corners should be rounded. Adhesion Strength (N / mm²) > 0,5
- The surfaces should be dry prior to application.
- The surface to be prepared for application should be primed Crack Bridging (mm) ≥1
with AquaRoll Easy-UV (1:1).
Elongation at break > % 200
Application
Application temperature Between +5°C and +35°C
- The material should be made ready for use by stirring with a
low-speed mixer. Resistance of hardened coat Between -25°C and +80°C
- It is applied additionally at least in 2 coats using a brush after
priming. Technical data are approximately provided according to a temperature
- The vertical wall insulation should extend to the base of +23°C and a relative humidity of 50%.
floor over base lateral walls and must be applied on an
approximately 300 mm of area as a measure of any humidity
Coverage
rising from the floor with capillary effect.
Approx. 1,5 kg / m² for each 1 mm thickness.
- The sides and the lateral parts of channels should be
The coverage amounts are theoretical and it is recommended
enriched using Bostik FlexMesh or Bostik FlashBand. To
to do coverage-controlled sample application before
ensure minimum application thickness in the horizontal
treatment.
surfaces, textile should also be used for enrichment.
- It is recommended to be sanding the uncured material of
Packaging
AquaRoll Easy-UV before the surface tiling.
5 kg and 20 kg plastic bucket.
- According to the TS EN 12004+A1’e göre C2T Class is
recommended for use with tile adhesive.
Storage
- They should be protected for water, frost and adverse
After application
weather conditions.
- In the first days, newly applied surfaces should be protected
- They should be kept dry and cool on wooden pallets at
from direct sunlight, severe air stream, high temperatures
between +10°C and +25°C in moisture free conditions.
(over +35°C), adverse air conditions such as rain and frost.
- The opened products should be closed immediately and
- All kinds of plaster applications on applied surfaces and
consumed first.
other applications like tiling should be done at least 3 days
- Maximum 3 buckets should be stocked on each other.
later.
- Shelf life is maximum12 months conditional to complying
- To obtain the recommended long term technical
with the above mentioned storage conditions.
performance of the product, after the completion of the all
application, the application and/or work should be covered
and protected with a suitable coating or covering (plaster,
Waterproofing

screed, ceramic, tile etc…) as early as possible (depending on

the product’s drying time within 3-7 days).

+5 ~ +35°C

max. 2 mm

1 12

Bostik Build Catalogue 45

 AquaRoll
Saniter
Liquid Membrane

Product Description
Bostik AquaRoll Saniter is a solvent-free, ready-to-use,
elastomeric resin-based, blue-coloured, liquid waterproofing
material that is applicable with a brush. It is produced in
accordance with European Union Standards and used for
protecting the buildings from harmful effects of water.
AquaRoll Saniter is suitable for use on the positive side only
and can be directly adhered on tiles.

Areas of applications
- Interior and exterior,
- In horizontal and vertical applications,
- In balconies and terraces,
- In wet places e.g. bathrooms and lavatories,
- In laboratories, warehouses, slaughterhouses, etc.

Features
- Flexible after curing.
- Resistant to crack formations on the application surface;
seamless.
- Applicable with a brush; easy to apply.
- Tiles and ceramics can be directly adhered on the material.
Sanding is not needed.
- Suitable for use in all kinds of mineral-based surfaces, stone
and stone-derivative bricks, pumice brick, briquette, aerated
concrete, concrete block, limestone, etc. built plastered TECHNICAL DATA
surfaces, cement-based plastered surfaces, grout and
concrete surfaces. Colour Light-Blue

Preparation of the substrate Applicable thickness (mm) Max 2

- The surfaces to be coated should be free of adhesive
Unit volume weight (kg/lt) 1,35 ± 0,2
preventive foreign substances such as dust, dirt, mould
oil, paint etc.; residues and wastes like cement, plaster and Viscosity (dPa s) 200,000 – 250,000
concrete should also be removed.
- The sub-surfaces that are not strong enough to carry Adhesion Strength (N / mm²) > 0,5
themselves e.g. cracked plasters, weak surfaces, or residues
of moss should be cleaned from the application surface. Crack Bridging (mm) ≥1
- The application surface must definitely be crack-free, stable Elongation at break > % 200
and strong. The gaps should be filled with Bostik 410 HP.
- Corners should be rounded. First drying time (h) 4
- The surfaces should be dry prior to application.
Fully dry after (h) 24 - 48
Application
Application temperature Between +5°C and +35°C
- The material should be made ready for use by stirring with a
low-speed mixer. Resistance of hardened coat Between -25°C and +80°C
- It is applied at least in 2 coats using a brush.
- The vertical wall insulation should extend to the base Technical data are approximately provided according to a temperature
floor over base lateral walls and must be applied on an of +23°C and a relative humidity of 50%.
approximately 300 mm of area as a measure of any humidity
rising from the floor with capillary effect.
Storage
- The sides and the lateral parts of channels should be
- They should be protected for water, frost and adverse
enriched using Bostik FlexMesh or Bostik FlashBand. To
weather conditions.
ensure minimum application thickness in the horizontal
- They should be kept dry and cool on wooden pallets at
surfaces, textile should also be used for enrichment.
between +10°C and +25°C in moisture free conditions.
- The torn and opened products should be closed
After application
immediately and consumed first.
- In the first days, newly applied surfaces should be protected
- Maximum 3 buckets should be stocked on each other.
from direct sunlight, severe air stream, high temperatures
- Shelf life is maximum 12 months conditional to complying
(over +35°C), adverse air conditions such as rain and frost.
with the above mentioned storage conditions.
- All kinds of plaster applications on applied surfaces and
other applications like tiling should be done at least 3 days
later.
- To obtain the recommended long term technical
performance of the product, after the completion of the all
application, the application and/or work should be covered
and protected with a suitable coating or covering (plaster,
screed, ceramic, tile etc…) as early as possible (depending on
the product’s drying time within 3-7 days).

Coverage
Approx. 1,5 kg / m² for each 1 mm thickness.
Waterproofing

The coverage amounts are theoretical and it is recommended

to do coverage-controlled sample application before
treatment.

Packaging
5 and 20 kg plastic bucket.

+5 ~ +35°C

max. 2 mm

1 12

46 Bostik Build Catalogue

PRODUCTS
AquaRoll AquaRoll AquaRoll AquaRoll
B1 Flex BC2 Performa BC2 BituCoat 32
2 Comp. 2 Comp.
1 Comp. Bituminous Fiber-Reinforced 2-Component
DESCRIPTION Bituminous Thick
Flexible Coating Bituminous Thick Bituminous Coating
Coating
Coating
- Interior and exterior - Interior and exterior, - Interior and exterior, - Interior and exterior,
- In foundations, - Only positive side, - Only positive side, - In foundations,
basements, - In foundations, - In foundations, basements,
underground structures basements, basements, underground
- In the waterproofing underground structures underground structures
of below ground - In the waterproofing structures - In the waterproofing
AREAS OF concrete structures. of below ground - In the waterproofing of below ground
APPLICATION concrete structures. of below ground concrete structures.
concrete structures.

- Rubber - bituminous - Flexible after curing, - Flexible after curing, - Applicable with a
waterproofing material, - Forms a solid - Forms a solid brush or a trowel;
- Flexible after dried, waterproofing waterproofing provides ease of
- Resistant to formation layer, layer, application.
of cracks on the - No seam formation, - No seam formation, - Resistant to usual
application surface, the - Excellent crack - Excellent crack loads on the ground.
seams will not occur, bridging ability, bridging ability,
FEATURES - Easy to apply with - Resistant to usual - Resistant to
brush and roll, loads on the ground, pressurized water.
- Resistant to usual - Resistant to
loads on the pressurized water.
ground.

Colour Black Black Black Black

Unit
Volume 1,20 ± 0,01 gr / cm3 1,10 ± 0,05 gr / cm3 1,20 ± 0,01 gr / cm3 1,15 ± 0,01 gr / cm3
Weight
TECHNICAL DATA

First
Drying Time
5 Hour 5 Hour 3 Hour 6 Hour

Full Dry
After
24 - 48 Hour 24 - 48 Hour 24 - 48 Hour 24 - 48 Hour

Mixing
Water - - - -
Amount

Coverage 1,5 kg / m² / mm 1,2 kg / m² / mm 1,2 kg / m² / mm 1,5 kg / m² / mm

Waterproofing

21 kg Plastic Drum 22 kg Plastic Drum

Packaging 30 kg Plastic Drum 32 kg Set
7 kg Bag 8 kg Bag

2K 2K 2K
A B A B A B

Max 6mm Max 6mm

1 1

Bostik Build Catalogue 47

 AquaRoll
B1 Flex
One-Component Bituminous Flexible Coating

Product Description
Bostik AquaRoll B1 Flex Bituminous Coating is a solvent-
free, ready-to-use, extra flexible, rubber - bituminous
waterproofing material that is applicable with a brush,
roller or spatula. It is produced in accordance with European
Union Standards and used for the protection of construction
elements under the ground or on the ground level in addition
to the insulation of some areas such as terraces, foundations,
basements etc. AquaRoll B1 Flex is suitable for use on the
positive side only. With official test certificate, DIN 18195.

Areas of applications
- Interior and exterior,
- In the foundations, basements and underground garages,
- In the waterproofing of below ground concrete structures.

Features
- Flexible after curing.
- Resistant to crack formations on the application surface;
seamless
- Applicable easily with a brush and roller.
- Resistant to the usual loads on the ground.
- Suitable for use in all kinds of mineral-based surfaces, stone
and stone-derivative bricks, pumice brick, briquette, aerated
concrete, concrete block, limestone, etc. built plastered
surfaces, cement-based plastered surfaces, grout and
concrete surfaces.
Technical data
Preparation of the substrate
- The surfaces to be coated should be free of adhesive Colour Black
preventive foreign substances such as dust, dirt, mould
oil, paint etc.; residues and wastes like cement, plaster and Applicable thickness (mm) Max 5
concrete should also be removed.
- The sub-surfaces that are not strong enough to carry Unit volume weight (kg/lt) 1,20 ± 0,01
themselves e.g. cracked plasters, weak surfaces, or residues pH 11,5 – 12,5
of moss should be cleaned from the application surface.
- The application surface must definitely be crack-free, stable Viscosity (cP) 7000
and strong. The gaps should be filled with Bostik 410 HP.
- Residues of bitumen-based waterproofing materials should Solid matter (%) 70,00 ± 1,00
be removed from the surface prior to application. The joints
with 2-5mm gaps should be filled with fine plaster prior to First drying time (h) 6
application.
- Air bubbles formation, which may occur due to gaps and Fully dry after (h) 24 - 48
pores, should be prevented during the process. For the
surface deformations deeper or wider than 5 mm, Bostik 410 Application temperature Between +5°C and +35°C
HP should be used in order to fill the joints. Resistance of hardened coat Between -25°C and +80°C
- Corners should be rounded.
- The surfaces should be dry prior to application. Technical data are approximately provided according to a temperature
- No water or wetness should remain between application of +23°C and a relative humidity of 50%.
surface and Bostik AquaRoll B1 Flex Bituminous Coating
during application. Optionally a cement-based waterproofing
mortar can be used as sandwich layer. - To obtain the recommended long term technical
performance of the product, after the completion of the all
Application application, the application and/or work should be covered
- The material should be made ready for use by stirring with a and protected with a suitable coating or covering (plaster,
low-speed mixer. screed, ceramic, tile etc…) as early as possible (depending on
- It is applied at least in 2 coats using a brush. the product’s drying time within 3-7 days).
- Expansion joints and seams should be covered respectively
with Bostik Flexband and Bostik AquaRoll B1 Flex Bituminous Coverage
Coating. Approx. 1,5 kg / m² for each 1 mm thickness.
- The vertical wall insulation should extend to the base The coverage amounts are theoretical and it is recommended
floor over base lateral walls and must be applied on an to do coverage-controlled sample application before
approximately 300 mm of area as a measure of any humidity treatment.
rising from the floor with capillary effect.
- In the brick walls, in order to prevent water from leaking Packaging
into the back of the insulation layer during the construction Bituminous component in 30 kg bucket.
process, Bostik AquaRoll B1 Flex Bituminous Coating
application should also include the base of the brick wall. Storage
- The sides and the lateral parts of channels should be - They should be protected for water, frost and adverse
enriched using Bostik FlexMesh. To ensure minimum weather conditions.
application thickness in the horizontal surfaces, textile - They should be kept dry and cool on wooden pallets at
should also be used for enrichment. between +10°C and +25°C in moisture free conditions.
- The torn and opened products should be closed
After application immediately and consumed first.
- In the first days, newly applied surfaces should be protected - Maximum 3 buckets should be stocked on each other.
Waterproofing

from direct sunlight, severe air stream, high temperatures - Shelf life is maximum 12 months conditional to complying
(over +35°C), adverse air conditions such as rain and frost. with the above mentioned storage conditions.
- All kinds of plaster applications on applied surfaces and
other applications like tiling should be done at least 3 days
later.

+5 ~ +35°C

max. 5 mm

1 6

48 Bostik Build Catalogue

AquaRoll
BC2 Performa
2-Component Fiber-Reinforced Bituminous Thick Coating

Product Description
Bostik AquaRoll BC2 Performa Bituminous Thick Coating is a
two component solvent free, fiber reinforced bitumen rubber
screeding compound for waterproofing material that is applicable
with a brush or a trowel. It is produced in accordance with
European Union Standards and used for the protection against
water leakage, floor humidity (capillary water absorption effect)
of construction elements under the ground or in the floor level.
AquaRoll BC2 Performa is suitable for use on the positive side only.

Areas of applications
- Interior and exterior,
- In the foundations, basements and underground garages,
- Protection of exposed concrete surface under the ground,

Features
- Flexible after curing.
- Resistant to crack formations on the application surface;
seamless.
- Applicable with a brush or a trowel; easy to apply.
- Resistant to water and root penetration
- Resistant to usual loads on the ground.
- Suitable for use in all kinds of mineral-based surfaces, stone and
stone-derivative bricks, pumice brick, briquette, aerated concrete,
concrete block, limestone, etc. built plastered surfaces, cement-
based plastered surfaces, grout and concrete surfaces.

Preparation of the substrate

- The surfaces to be coated should be free of adhesive preventive
foreign substances such as dust, dirt, mould oil, paint etc.; residues Technical data
and wastes like cement, plaster and concrete should also be
removed. Colour Black
- The sub-surfaces that are not strong enough to carry themselves
e.g. cracked plasters, weak surfaces, or residues of moss should be Applicable thickness (mm) Max 6
cleaned from the application surface.
- The application surface must definitely be crack-free, stable and Unit volume weight of the mixture 1,10 ± 0,05 (kg/lt)
strong. The gaps should be filled with Bostik 410 HP.
- Residues of bitumen-based waterproofing materials should be pH 8,5 – 11,0
removed from the surface prior to application. The joints with
2-5mm gaps should be filled with fine plaster or applying Bostik Viscosity (cP) 100000 ± 5000
AquaRoll BC2 Performa with a trowel prior to application.
- Air bubbles formation, which may occur due to gaps and Solid matter (%) 70,00 ± 2,00
pores, should be prevented during the process. For the surface
deformations deeper or wider than 5 mm, Bostik 410 HP should be First drying time (h) ~5
used in order to fill the joints.
- Corners should be rounded. Fully dry after (h) 24 – 48
- The surfaces should be dry prior to application.
- No water or wetness should remain between application surface Application temperature Between +5°C and +35°C
and Bostik AquaRoll BC2 Performa Fiber-Reinforced Bituminous
Thick Coating during the application. Optionally a cement-based Resistance of hardened coating Between -25°C and +80°C
waterproofing mortar can be used as sandwich layer.
Technical data are approximately provided according to a temperature
Application of +23°C and a relative humidity of 50%.
- The material should be made ready for use by stirring with a low-
speed mixer.
- Firstly, the bituminous component of AquaRoll BC2 Performa - To obtain the recommended long term technical performance
Fiber-Reinforced Bituminous Thick Coating is stirred shortly of the product, after the completion of the all application, the
and then powder component added on and finally the mixture is application and/or work should be covered and protected with a
stirred until it becomes smooth and homogeneous. suitable coating or covering (plaster, screed, ceramic, tile etc…) as
- It is applied at least in 2 coats using a brush or a trowel. early as possible (depending on the product’s drying time within
- Expansion joints and seams should be covered respectively 3-7 days).
with Bostik Flexband and Bostik AquaRoll BC2 Performa Fiber-
Reinforced Bituminous Thick Coating. Coverage
- The vertical wall insulation should extend to the base floor over Approx. 1,2 kg / m² for each 1 mm thickness.
base lateral walls and must be applied on an approximately 300 4,0 kg / m² against base humidity.
mm of area as a measure of any humidity rising from the floor with 4,0 kg / m² against non-pressurized water.
capillary effect. 6,0 kg / m² against pressurized water.
- In the brick walls, in order to prevent water from leaking into The coverage amounts are theoretical and it is recommended to
the back of the insulation layer during the construction process, do coverage-controlled sample application before treatment.
Bostik AquaRoll BC2 Performa Fiber-Reinforced Bituminous Thick
Coating application should also include the base of the brick wall. PackaginG
- In the moving floors with cracking risk, Bostik FlexMesh can be Bituminous component in 21 kg plastic bucket.
placed between the applications as a backing coat in order to meet Powder component in 7 kg craft bag.
the tensile stress and form a more flexible water layer. 28 kg in sets.
- The sides and the lateral parts of channels should be enriched
using Bostik FlexMesh. To ensure minimum application thickness Storage
in the horizontal surfaces, textile should also be used for - They should be protected for water, frost and adverse weather
enrichment. conditions.
- They should be kept dry and cool on wooden pallets at between
After application +10°C and +25°C in moisture free conditions.
- In the first days, newly applied surfaces should be protected - The torn and opened products should be closed immediately and
Waterproofing

from direct sunlight, severe air stream, high temperatures (over consumed first.
+35°C), adverse air conditions such as rain and frost. - Maximum 3 buckets should be stocked on each other.
- All kinds of plaster applications on applied surfaces and other - Shelf life is maximum12 months conditional to complying with
applications like tiling should be done at least 3 days later. the above mentioned storage conditions.

+5 ~ +35°C
2K
A B
max. 6 mm

1 4

Bostik Build Catalogue 49

 AquaRoll
BC2
2-Component Bituminous Thick Coating

Product Description
Bostik AquaRoll BC2 Bituminous Thick Coating is a solvent-free,
two-component, flexible waterproofing material based on a
unique combination of rubber and bitumen that is applicable with
a brush or a trowel. It is produced in accordance with European
Union Standards and used for the protection against water leakage,
floor humidity (capillary water absorption effect) of construction
elements under the ground or in the floor level. AquaRoll BC2
is suitable for use on the positive side only. With official test
certificate, DIN 18195.

Areas of applications
- Interior and exterior,
- In the foundations, basements and underground garages,
- In the waterproofing of below ground concrete structures.

Features
- Flexible after curing.
- Resistant to crack formations on the application surface;
seamless.
- Applicable with a brush or a trowel; easy to apply.
- Resistant to usual loads on the ground.
- Suitable for use in all kinds of mineral-based surfaces, stone and
stone-derivative bricks, pumice brick, briquette, aerated concrete,
concrete block, limestone, etc. built plastered surfaces, cement-
based plastered surfaces, grout and concrete surfaces.

Preparation of the substrate

- The surfaces to be coated should be free of adhesive preventive
foreign substances such as dust, dirt, mould oil, paint etc.; residues Technical data
and wastes like cement, plaster and concrete should also be
removed. Colour Black
- The sub-surfaces that are not strong enough to carry themselves
e.g. cracked plasters, weak surfaces, or residues of moss should be Applicable thickness (mm) Max 6
cleaned from the application surface.
- The application surface must definitely be crack-free, stable and Unit volume weight of the mixture 1,20 ± 0,01 (kg/lt)
strong. The gaps should be filled with Bostik 410 HP.
- Residues of bitumen-based waterproofing materials should be pH 11,5 – 12,5
removed from the surface prior to application. The joints with
2-5mm gaps should be filled with fine plaster or applying Bostik Viscosity (cP) 6000
AquaRoll BC2 with a trowel prior to application.
- Air bubbles formation, which may occur due to gaps and Solid matter (%) 70,00 ± 1,00
pores, should be prevented during the process. For the surface
deformations deeper or wider than 5 mm, Bostik 410 HP should be First drying time (h) ~6
used in order to fill the joints.
- Corners should be rounded. Fully dry after (h) 24 – 48
- The surfaces should be dry prior to application.
- No water or wetness should remain between application surface Application temperature Between +5°C and +35°C
and Bostik AquaRoll BC2 Bituminous Thick Coating during the
application. Optionally a cement-based waterproofing mortar can Resistance of hardened coating Between -25°C and +80°C
be used as sandwich layer.
Technical data are approximately provided according to a temperature
Application of +23°C and a relative humidity of 50%.
- The material should be made ready for use by stirring with a low-
speed mixer.
- Firstly, the bituminous component of AquaRoll BC2 Bituminous - To obtain the recommended long term technical performance
Thick Coating is stirred shortly and then powder component added of the product, after the completion of the all application, the
on and finally the mixture is stirred until it becomes smooth and application and/or work should be covered and protected with a
homogeneous. suitable coating or covering (plaster, screed, ceramic, tile etc…) as
-It is applied at least in 2 coats using a brush or a trowel. early as possible (depending on the product’s drying time within 3-7
- Expansion joints and seams should be covered respectively with days).
Bostik Flexband and Bostik AquaRoll BC2 Bituminous Thick Coating.
- The vertical wall insulation should extend to the base floor over Coverage
base lateral walls and must be applied on an approximately 300 Approx. 1,2 kg / m² for each 1 mm thickness.
mm of area as a measure of any humidity rising from the floor with 3,0 kg / m² against base humidity.
capillary effect. 4,0 kg / m² against non-pressurized water.
- In the brick walls, in order to prevent water from leaking into the 6,0 kg / m² against pressurized water.
back of the insulation layer during the construction process, Bostik The coverage amounts are theoretical and it is recommended to do
AquaRoll BC2 Bituminous Thick Coating application should also coverage-controlled sample application before treatment.
include the base of the brick wall.
- In the moving floors with cracking risk, Bostik FlexMesh can be Packaging
placed between the applications as a backing coat in order to meet Bituminous component in 22 kg plastic bucket.
the tensile stress and form a more flexible water layer. Powder component in 8 kg craft bag.
- The sides and the lateral parts of channels should be enriched 30 kg in sets.
using Bostik FlexMesh. To ensure minimum application thickness in
the horizontal surfaces, textile should also be used for enrichment. Storage
- They should be protected for water, frost and adverse weather
Application with machine: conditions.
AquaRoll BC2 is suitable for use with sprayable machine. Consult - They should be kept dry and cool on wooden pallets at between
Bostik Technical Service for machine use. +10°C and +25°C in moisture free conditions.
- The torn and opened products should be closed immediately and
Waterproofing

After application consumed first.

- In the first days, newly applied surfaces should be protected from - Maximum 3 buckets should be stocked on each other.
direct sunlight, severe air stream, high temperatures (over +35°C), - Shelf life is maximum12 months conditional to complying with the
adverse air conditions such as rain and frost. above mentioned storage conditions.
- All kinds of plaster applications on applied surfaces and other
applications like tiling should be done at least 3 days later.

+5 ~ +35°C
2K
A B
max. 6 mm

1 4

50 Bostik Build Catalogue

AquaRoll
BituCoat 32
2-Component Bituminous Coating

Product Description
Bostik AquaRoll BituCoat 32 Bituminous Coating is a solvent-
free, two-component polymer bituminous with added
rubber waterproofing material. AquaRoll BituCoat 32 is
suitable for use on the positive side only. With official test
certificate, DIN 18195.

Areas of applications
- Only for outdoors,
- In the foundations, basements and underground garages,
- In the waterproofing of below ground concrete structures.

Features
- Resistant to crack formations on the application surface;
seamless.
- Applicable with a brush or a trowel; provides ease of
application.
- Resistant to usual loads on the ground.
- Suitable for use cement-based plastered surfaces, grout
and concrete surfaces.

Preparing the substrate

- The surfaces to be coated should be free of adhesive
preventive foreign substances such as dust, dirt, mould
oil, paint etc.; residues and wastes like cement, plaster and
concrete should also be removed.
- The sub-surfaces that are not strong enough to carry
themselves e.g. cracked plasters, weak surfaces, or residues Technical data
of moss should be cleaned from the application surface.
- The application surface must definitely be crack-free, stable Colour Black
and strong. The gaps should be filled with Bostik 410 HP.
- Residues of bitumen-based waterproofing materials should Applicable thickness (mm) Max 6
be removed from the surface prior to application. The joints
with 2-5mm gaps should be filled with fine plaster Unit volume weight of the mixture 1,15 ± 0,1 (kg/lt)
- Air bubbles formation, which may occur due to gaps and pH ~ 10,0 – 11,0
pores, should be prevented during the process. For the
surface deformations deeper or wider than 5 mm, Bostik 410 Viscosity (cP) 5000
HP should be used in order to fill the joints.
- Corners should be rounded. Solid content (%) 60,00 ± 1,00
- The surfaces should be dry prior to application.
- No water or wetness should remain between application First drying time (h) ~6
surface and Bostik AquaRoll BituCoat 32 Bituminous
Coating during the application. Optionally a cement-based Fully dry after (h) 24 - 48
waterproofing mortar can be used as sandwich layer.
- The surface to be prepared for application should be primed Application temperature Between +5°C and +35°C
with AquaRoll Bitumy. Resistance of hardened coating Between -25°C and +80°C
Application Technical data are approximately provided according to a temperature
- The material should be made ready for use by stirring with a of +23°C and a relative humidity of 50%.
low-speed mixer.
- Firstly, the bituminous component of AquaRoll BituCoat
32 Bituminous Coating is stirred shortly and then powder - To obtain the recommended long term technical
component added on and finally the mixture is stirred until it performance of the product, after the completion of the all
becomes smooth and homogeneous. application, the application and/or work should be covered
- It is applied at least in 2 coats using a brush or a trowel. and protected with a suitable coating or covering (plaster,
- Expansion joints and seams should be covered respectively screed, ceramic, tile etc…) as early as possible (depending on
with Bostik Flexband and Bostik AquaRoll BituCoat 32 the product’s drying time within 3-7 days).
Bituminous Coating.
- The vertical wall insulation should extend to the base Coverage
floor over base lateral walls and must be applied on an Approx. 1,5 kg / m² for each 1 mm thickness.
approximately 300 mm of area as a measure of any humidity The coverage amounts are theoretical and it is recommended
rising from the floor with capillary effect. to do coverage-controlled sample application before
- In the brick walls, in order to prevent water from leaking treatment.
into the back of the insulation layer during the construction
process, Bostik AquaRoll BituCoat 32 Bituminous Coating Packaging
application should also include the base of the brick wall. Bituminous component in 24 kg plastic bucket.
- In the moving floors with cracking risk, Bostik FlexMesh can Powder component in 8 kg craft bag.
be placed between the applications as a backing coat in order 32 kg lık set halinde
to meet the tensile stress and form a more flexible water
layer. Storage
- The sides and the lateral parts of channels should be - They should be protected for water, frost and adverse
enriched using Bostik FlexMesh. To ensure minimum weather conditions.
application thickness in the horizontal surfaces, textile - They should be kept dry and cool on wooden pallets.
should also be used for enrichment. - The torn and opened products should be closed
immediately and consumed first.
Waterproofing

After application - Maximum 3 buckets should be stocked on each other.

- In the first days, newly applied surfaces should be protected - Shelf life is maximum 12 months conditional to complying
from direct sunlight, severe air stream, high temperatures with the above mentioned storage conditions.
(over +35°C), adverse air conditions such as rain and frost.
- All kinds of plaster applications on applied surfaces and
other applications like tiling should be done at least 3 days
later.

+5 ~ +35°C
2K
A B
max. 6 mm

1 6

Bostik Build Catalogue 51

 FlexBand
MonoFlex
TPE Based Waterproofing Tape for Dilatation Joints

Product description
FlexBand MonoFlex is a high performance thermoplastic
elastomer waterproofing tape for between building
expansion, dilatation and construction joints.

Areas of application
- In dilatation joints,
- In outside expansions,
- In construction joints.

Application
- Bostik GroPox epoxy adhesive should be applied on the
outer surface of dilatation joints with a trowel.
- After the placed FlexBand MonoFlex on the dilatation joints,
apply the 2nd coat epoxy adhesive on the 1nd coat as wet on
wet.
- Provide the desired elongation of the FlexBand MonoFlex
should not be allowed to infect the adhesive the middle
part of the waterproofing tape. It is adhered on the floor
by reversing (omega) in the joint with Bostik GroPox epoxy
mortar.

Chemical Properties
Hydrochloric acid 3% + Internal
Technical Data
Sulphuric acid 35% + Internal
Thermoplastic
Material composition
Citric acid 100 g/l + Internal Elastomer
Lactic acid 5% + Internal Color Grey
Potassium hydroxide 3% / 20% +/+ Internal Shore A hardness 87
Sodium hypochlorite 0,3 g/l + Internal Burst pressure, max. >4,0 bar Internal
Salt water Breaking load DIN EN ISO
+ Internal 14,0 N/mm²
(20 g/l Sea water salt) longitudinal 527-3
DIN EN ISO
Breaking load lateral 14,0 N/mm²
Packaging 527-3

Width (mm) 200 300 Extension break DIN EN ISO

%1000
longitudinal 527-3
Thickness (mm) 1 1
Power absorption at DIN EN ISO
3,0 N/mm
Length (m/roll) 20 20 25% Elasticity lateral 527-3
Type With hole With hole Power absorption at DIN EN ISO
3,5 N/mm
50% Elasticity lateral 527-3
Resistance to water DIN EN 1928
>5 bar
pressure (Version B)
Bonding strength >4,0 N/mm² * DIN EN 1348
Resistance to tearing
100 N / 100 N DIN EN 12310-2
longitudinal / lateral
Peel test wood > 100 N * Internal
DIN EN ISO
UV-Resistance, min. 6500 h **
4892-2
Resistance to
-30°C ile +90°C arası
temperature
Fire classification B2 DIN EN 4102
* in dependence from the used adhesive
** still to be verified by additional tests
Waterproofing

52 Bostik Build Catalogue

FlexBand L
Flexible Sealing Band

Product description
FlexBand L is an flexible sealing band with elastic armure
in edges and its center integrated with elastic rubber. It is
suitable for use in Bostik CemenTech and Bostik AquaRoll
series waterproofing systems and used in order to prevent
water to leak through the cracks from one side to another as
a result of building movements.

Areas of application
- In critical corners that tend to crack,
- In vertical-horizontal joints,
- In vertical-vertical joints,
- In the cracks arising from constructional movements.

Application
- It is placed in the intermediate layer of waterproofing
material in two coats to cover the stress.

Ambalaj
A roll with 10 cm width, 50 mt length.

FlexBand V
Elastik Boru Manşeti
Product description
FlexBand V is a wall-type flexible collar with elastic armure
in edges and its center integrated with elastic rubber. It is
suitable for use in Bostik CemenTech and Bostik AquaRoll
series waterproofing systems and used in order to prevent
water to leak through the cracks from one side to another as
a result of building movements.

Areas of application
- Around installation pipes,
- Around armatures, etc,
- In places where various constructional materials go
through the reinforced concrete system.
- In the cracks arising from constructional movements.

Application
- It is placed in the intermediate layer of waterproofing
material in two coats to cover the stress.

Ambalaj
25 pcs box in 12 cm x 12 cm size.

FlexBand H
Flexible Collar
Product description
FlexBand H is a floor-type flexible collar with elastic armure
in edges and its center integrated with elastic rubber. It is
suitable for use in Bostik CemenTech and Bostik AquaRoll
series waterproofing systems and used in order to prevent
water to leak through the cracks from one side to another as
a result of building movements.

Areas of application
Waterproofing

- Around installation pipes,

- In water outlets,
- Around armatures, etc,
- In places where various constructional materials overlap
the reinforced concrete system,
- In the cracks arising from constructional movements.

Application
It is placed in the intermediate layer of waterproofing
material in two coats to cover the stress.

Ambalaj
10 pcs box in 42 cm x 42 cm size.

Bostik Build Catalogue 53

 FlexBand 90
Flexible Inner Corner Band

Product description
FlexBand 270 is a flexible band with elastic armure in edges
and its center integrated with elastic rubber. It is suitable
for use in order to obtain more straight insulation of inner
corners that can be used with FlexBand L in the system.

Areas of application
In critical inner corners which are susceptible to cracks.

Application
It is placed in the intermediate layer of waterproofing
material in two coats to cover the stress.

Ambalaj
25 pcs in boxes

FlexBand 270
Flexible Outer Corner Band
Product description
FlexBand 270 is a flexible band with elastic armure in edges
and its center integrated with elastic rubber. It is suitable
for use in order to obtain more straight insulation of outer
corners that can be used with FlexBand L in the system.

Areas of application
In critical outer corners which are susceptible to cracks.

Application
It is placed in the intermediate layer of waterproofing
material in two coats to cover the stress.

Ambalaj
25 pcs in boxes

FlexBand DL 140/DL 240

Flexible Expansion Joint Band

Product description
FlexBand DL 140 is a flexible band that can be used for
expansion among the buildings, dilatation and insulation of
constructional joints. It has been more resistant to aging
and more flexible by integrating with thermoplastic rubber.
Bostik FlexBand DL 240 can be used within Bostik CemenTech
and Bostik AquaRoll series waterproofing systems or adhered
Waterproofing

on the floor with Bostik GroPox epoxy mortar.

Areas of application
In dilatation joints; In expansion joints; In constructional joints
Application
It is placed in the intermediate layer of waterproofing
material in two coats to cover the stress. It is adhered on the
floor by reversing (omega) in the joint with Bostik GroPox
epoxy mortar.
Ambalaj
Roll with 140 mm width and 30 m length
Roll with 240 mm width and 30 m length

54 Bostik Build Catalogue

FlexBand Butil
Butyl Band

Product description
FlexBand Butyl is a self adhesive, flexible band that is made
from butyl and can be used for the insulation of cracks within
Bostik CemenTech and Bostik AquaRoll systems.

Areas of application
For cracks; For joints

Application
It is placed in the intermediate layer of waterproofing
material in two coats to cover the stress.

Ambalaj
Roll with 25 m length

SwellTape
Swelling Tape

Product Description
Bostik SwellTape is a self-adhesive, natural sodium bentonite-
based, new generation, swelling tape in rolls that is expanded
when contacted with water and composed of elastic materials. It
is a tape with cord appearance which can be used in the concrete
joints in construction sites.

Areas of applications
- In foundations, pools, tunnels, garages, water tanks and
drainages,
- In concrete shears,
- In the joints of precast components,
- In manholes,
- In sustaining walls,
- In old-new concrete connection spots,
- In underground pipe and cable transition areas,
- In water treatment plants.

Features
- Fills all the cracks, pores and capillary voids when contacted
with water.
- Provides impermeability by penetrating into the concrete.
- Forms an active pressure against water in the concrete.
- Excellent compliance with deformed surfaces and joints.
- Saves time and labour.
- Holds suitable varieties and sizes for all kind of application.

Application
No any adhesive or welding procedure is needed during the
application. It is self-adhesive (for concrete, pvc, steel and wood).

Coverage
1 mt/mt

Packaging
In 7 mt rolls – 49 mt in box

Storage
Waterproofing

Shelf life is maximum 12 months in its original package when

stored in a dry, clean and water- and humidity-free place.

Bostik Build Catalogue 55

 N

Swell-PolyTape
E
W

Polymer Based Swelling Tape

Product Description
Bostik Swell-PolyTape is a thermoplastic elastomer tape, that
is used in the concrete joints to prevent water transition. It
has the capability of %800 expansion.

Areas of applications
- In pools and water tanks,
- In tunnels, metros and garages
- In drainages and water treatment plants.
- In the joints of foundations and basement walls subject to
water.

Features
- Fills all the cracks, pores and capillary voids when contacted
with water.
- Provides impermeability by penetrating into the concrete.
- Forms an active pressure against water in the concrete.
- Excellent compliance with deformed surfaces and joints.
- Saves time and labour.
- Holds suitable varieties and sizes for all kind of application.

Preparation of the substrate

- In all applications, general construction standards and
technical application specifications must be taken into
consideration.
- The surfaces to be coated should be free of adhesive Technical datA
preventive foreign substances such as dust, dirt, mould oil,
paint, water etc.; residues and wastes like cement, plaster Colour Blue
and concrete should also be removed.
Size (mm) 20 x 5
Application
Density (at 25°C) (gr/cm³) 1,25
- The Swell-PolyTape has to be settled min. 8 cm. away from
the point that subject to water. At the beginning: 5 x 20 x 150mm
- A relavent adhesive can be used. After 2 hours :7 x 24 x 160mm (180%)
- In the joints of the tape, the ends must be side by side min. Expansion Capability
After 24 hours: 9 x 34 x 225mm (459%)
50mm. After 8 days: 10 x 44 x 278mm (815%)
- After 8 hours ,concrete can be poured.
- After the application, the tape must be prevented from Expansion pressure 1,06 N/mm²
water until the concrete is poured..
Water Pressure
Packaging Resistance
2 bar
5 x 20 mm- 40 mt/roll Joint width 2,5 mm
1,5 bar
Joint width 1,0 mm
Storage Toxicity No
Shelf life is maximum 12 months in its original package when
stored in a dry, clean and water- and humidity-free place. Fire Resistance Class E (DIN EN 13501-1)
Technical data are approximately provided according to a temperature
of + 23°C and a relative humidity of 50%.
Waterproofing

56 Bostik Build Catalogue

 Application - Dilatation Joints

STEP:1 STEP:2 STEP:3

Bostik GroPox epoxy adhesive should FlexBand MonoFlex waterproofing tape After the placed FlexBand MonoFlex on
be applied on the outer surface of is placed in reverse omega-made joints. the dilatation joints, apply the 2nd coat
dilatation joints with a trowel. epoxy adhesive on the 1nd coat as wet
on wet.

Application - FlexBand

STEP:1 STEP:2 STEP:3

Liquid waterproofing membrane should Upon the first coat application of waterproofing Flexband tapes should be laid to adhere
be applied to the edges of corner joints material used on the entire substrate, side wings firmly to the surface without any pot.
with trowel or brush. of Flexband waterproofing tapes are placed
on waterproofing applied substrates when
waterproofing material is still wet. Additional space
should be created at least 5 cm overlay for.
Waterproofing

STEP:4 STEP:5

Second coat waterproofing material is After Flexband installation, should

applied in a way to cover the side wings be start main waterproofing layer
of Flexband waterproofing tapes. application.

Bostik Build Catalogue 57

 Wet Area Bathroom
Waterproofing Detail

1
6 7

5
2

4
3
Waterproofing

1 Tiling Grout - CeraBest Fuga Series 5 Waterproofing I.Layer - CemenTech Series

2 Ceramic 6 Primer (if necessary)
3 Tile Adhesive - CeraBest Series 7 Exposed Concrete
4 Waterproofing II.Layer - CemenTech Series

58 Bostik Build Catalogue

 Pool & Water Tank
Waterproofing

11

11
2 9
7 8
3 5 6
4

10

1 Water 7 Waterproofing I.Layer - CemenTech Series

2 Tiling Grout 8 Primer (if necessary)
Waterproofing

3 Ceramic 9 Self levelling Screed - Roxol Series

4 Tile Adhesive - CeraBest Series 10 Concrete / Static Concrete
5 Plaster, Screed (if necessary) 11 Repair of shift rod-chamfer and wedge etc.
6 Waterproofing II.Layer - CemenTech Series

Bostik Build Catalogue 59

 Foundation Wall
Insulation

1
2

10 5

9
10

1 Land 6 Waterproofing I.Layer - AquaRoll Bitumen Series

Waterproofing

2 Drainage Layer 7 Primer (if necessary)

3 Bostik ClimaTech 8 Plaster - Meister Series (if necessary)

4 Bostik AquaRoll B1 Flex - Bituminous Adhesive 9 Exposed Concrete

5 Waterproofing II.Layer - AquaRoll Bitumen Series 10 Repair of shift rod-chamfer and wedge etc.

60 Bostik Build Catalogue

 Trafficable
Flat Roof Detail

1
2

6
7

8 9

10
11

12

1 Tiling Grout - CeraBest Fuga Series 7 Seperator

2 Ceramic 8 Waterproofing II.Layer / AquaRoll Series
Waterproofing

3 Tile Adhesive - CeraBest Series 9 Waterproofing I.Layer / AquaRoll Series

4 Self levelling Screed - Roxol Series 10 Primer (if necessary)
5 Filter Layer 11 Reinforced concrete slope (slope >%2)
6 Bostik ClimaTech 12 Concrete / Static Concrete

Bostik Build Catalogue 61

 Green Roofing
Waterproofing

2
3
4
5

7
8

10

11

1 Plant Layer 7 Waterproofing II.Layer - AquaBlocker or AquaRoll Series

2 Land 8 Waterproofing I.Layer - AquaBlocker or AquaRoll Series

Waterproofing

3 Filter Layer / Geotextile 9 Primer (if necessary)

4 Drainage Layer 10 Reinforced concrete slope (slope>%2)
5 Bostik ClimaTech 11 Exposed Concrete / Static Concrete
6 Seperator

62 Bostik Build Catalogue

 Non-Trafficable
Flat Roof Detail

1
2

3 4

6
7

1 Waterproofing II.Layer - AquaBlocker 6 Bostik ClimaTech

Waterproofing

2 Waterproofing I.Layer - AquaBlocker 7 Water vapour barrier

3 Primer (if necessary) 8 Primer
4 Reinforced concrete slope (slope>%2) 9 Exposed Concrete / Static Concrete
5 Filter Layer / Geotextile

Bostik Build Catalogue 63