Series LFN45B Specification Sheet
Uploaded by
WattsSeries LFN45B Specification Sheet
Uploaded by
WattsES-LFN45B
For Residential and Commercial Applications
Job Name Job Location Engineer Approval Contractor Approval Contractors P.O. No. Representative
LEAD FREE* Series LFN45B-M1
Sizes: 12" 1" (15 25mm)
LFN45BDU-M1
Water Pressure Reducing Valves**
Series LFN45B-M1 Water Pressure Reducing Valves are designed to reduce incoming water pressure to a sensible level to protect plumbing system components and reduce water consumption. The LFN45B features Lead Free* construction to comply with Lead Free* installation requirements. This series is suitable for water supply pressures up to 400psi (27.6 bar) and may be adjusted from 25 75psi (172 517 kPa). The standard setting is 50psi (345 kPa). All parts are quickly and easily serviceable without removing the valve from the line. The standard bypass feature permits the flow of water back through the valve into the main when pressures, due to thermal expansion on the outlet side of the valve, exceed the pressure in the main supply.
Features
Double union inlet & outlet connections (option DU) Integral stainless steel strainer Thermoplastic seat & cage Lead Free* cast copper silicon alloy body construction Serviceable in line Bypass feature controls thermal expansion pressure*** Sealed spring cage on all models for accessible outdoor or pit installations
Reinforced Diaphragm Threaded, solder PEX, CPVC, or QC ends Integral Stainless Steel Strainer
Models
LFN45B-M1 NPT threaded female inlet x NPT female outlet LFN45BU-M1 NPT threaded union inlet x NPT female outlet LFN45BU-S-M1 Solder union inlet x NPT female outlet LFN45BU-QC-M1 Single Union QC union inlet LFN45BDU-M1 Double Union NPT threaded union female inlet and outlet LFN45BDU-S-M1 Double Union Solder union inlet and outlet LFN45BDU-PEX-M1 Double Union PEX union inlet and outlet (3/4" and 1" only) LFN45BDU-CPVC-M1 Double Union CPVC union inlet and outlet (3/4" and 1" only) LFN45BDU-QC-M1 Double Union QC union inlet and outlet (3/4" and 1" only)
Thermal Expansion Bypass
Thermoplastic Seat
Specifications
Standard Specifications: A Water Pressure Reducing Valve with integral strainer shall be installed in the water service pipe near its entrance to the building where supply main pressure exceeds 60psi (413 kPa) to reduce it to 50psi (345 kPa) or lower. The water pressure reducing valve shall be constructed using Lead Free* materials. Lead Free* regulators shall comply with state codes and standards, where applicable, requiring reduced lead content. The valve shall feature a Lead Free* cast copper silicon alloy body suitable for water supply pressures up to 400psi (27.6 bar). Provision shall be made to permit the bypass flow of water back through the valve into the main when pressures, due to thermal expansion on the outlet side of the valve, exceed the pressure in the main supply. Water Pressure Reducing Valve with built-in bypass check valves and integral strainer will be acceptable. Approved valve shall be listed to ASSE 1003 and IAPMO and certified to CSA B356. Valve shall be a Watts Series LFN45B-M1.
* The wetted surface of this product contacted by consumable water contains less than 0.25% of lead by weight. ** A water saving test program concluded that reducing the supply pressure from 80-50psi (551-345 kPa) resulted in a water savings of 30%. *** The bypass feature will not prevent the pressure relief valve from opening on the hot water supply system with pressure above 150psi (10.3 bar).
Watts product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements, please contact Watts Technical Service. Watts reserves the right to change or modify product design, construction, specifications, or materials without prior notice and without incurring any obligation to make such changes and modifications on Watts products previously or subsequently sold.
Materials
Body: Seat: Cage: Integral Strainer: Diaphragm: Valve Disc: Lead Free* cast copper silicon alloy Thermoplastic Thermoplastic Stainless steel Reinforced EPDM Elastomer
Capacity
kPa psi 0 0 34.5 5 10 15 20 25 0 10 20 30 40 gpm 0 37.3 75.7 113.6 151.4 lpm
Pressure Drop
Pressure Temperature
Temperature Range: 33F 180F (0.5C 82C) Maximum Working Pressure: 400psi (27.6 bar) Adjustable Reduced Pressure Range: 25 75psi (172 517 kpa) Standard Reduced Pressure Setting: 50psi (345 kpa)
68.9 103.4 137.8 172.3
Standards
Meets requirements of ASSE Standard 1003; (ANSI A112.26.2) and CSA Standard B356. Certified by NSF to ANSI/NSF Standard 61 Annex G. Listed by IAPMO and City of Los Angeles.
Flow
Options
Add Suffix
FNPT
G GG
Gauge tapping Gauge tapping and 160psi (11.0 bar) gauge
ENPT FSWEAT
Dimensions Weights
ESWEAT FPEX C
FEMALE NPT THREAD BOTH ENDS OF BODY
EPEX FCPVC D
A A+E A+E+E
ABOVE VALVE SHOWN WITH SINGLE NPT UNION CONNECTION ON INLET VALVES MAY BE ORDERED WITH 0,1,OR 2 UNION CONNECTIONS USING ANY COMBINATION OF NPT, SOLDER, PEX OR CPVC CONNECTIONS REQUIRED F DIMENSIONS ARE APPROXIMATE ENGAGEMENT LENGTHS.
ECPVC FQC
EQC
Size (DN) Dimensions WEIGHT
A C D ENPT ESWEAT EPEX ECPVC EQC FNPT FSWEAT FPEX FCPVC FQC G in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm lbs. kgs.
12 34
15 3716 88 4916 116 11116 43 58 20 3716 88 4916 116 11116 43 58 1 25 418 105 4916 116 11116 43 34
16 58 16 78 20 1
15 1316 21 1516 26 118
21 916 15 1716 36 12 24 1316 21 1916 40 916 29 1116 26 11116 43 1116
13 12 14 34 17 1516
13 58 19 58 23 1316
16 12 13 112 38 214 57 2 .91 16 34 18 11116 42 214 57 2 .91 21 1516 23 134 45 214 57 3 1.36
A Watts Water Technologies Company
USA: Tel: (978) 688-1811 Fax: (978) 794-1848 www.watts.com Canada: Tel: (905) 332-4090 Fax: (905) 332-7068 www.watts.ca
ES-LFN45B
1323
2013 Watts
