Technical Information

Deltabar S PMD70/75, FMD76/77/78

Differential pressure transmitter
with ceramic and silicon sensors
Overload-resistant and function-monitored, Communication via
HART, PROFIBUS PA or FOUNDATION Fieldbus

Application Your benefits

The Deltabar S differential pressure transmitter is used • Very good reproducibility and long-term stability
for the following measuring tasks: • High reference accuracy: up to ±0.075%,
• Flow measurement (volume or mass flow) in as PLATINUM version: ±0.05%
conjunction with primary elements in gases, vapours • Turn down 100:1, higher on request
and liquids • Used for flow and differential pressure monitoring
• Level, volume or mass measurement in liquids up to SIL 3, certified to IEC 61508 by TÜV SÜD
• Differential pressure monitoring, e.g. of filters and • HistoROM®/M-DAT memory module
pumps • Function-monitored from the measuring cell to the
• International usage thanks to a wide range of approvals electronics
• Continuous modularity for differential pressure,
hydrostatic and pressure (Deltabar S, Deltapilot S,
Cerabar S), e.g.
– replaceable display
– universal electronics for pressure and
differential pressure
• Quick commissioning thanks to quick setup menu
• Easy and safe menu-guided operation on-site,
via 4...20 mA with HART, via PROFIBUS PA or
via FOUNDATION Fieldbus
• Extensive diagnostic functions

TI382P/00/en/12.07
No. 71060097
 Deltabar S

Table of contents

Function and system design. . . . . . . . . . . . . . . . . . . . . 4 Total Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Device selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Warm-up period – PMD75, FMD77, FMD78 . . . . . . . . . . . . . . . 25
Overview of diaphragm seal FMD78 . . . . . . . . . . . . . . . . . . . . . . . 5 Influence of the operating pressure on zero point and span – PMD75,
Measuring principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 FMD77, FMD78 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Flow measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Thermal change of the zero output and the output
Level measurement (level, volume and mass) . . . . . . . . . . . . . . . . 9 span -- PMD75 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Communication protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Performance characteristics – ceramic diaphragms . . 26
Human interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Reference accuracy – PMD70, FMD76 . . . . . . . . . . . . . . . . . . . 26
On-site display (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Total performance – PMD70, FMD76 . . . . . . . . . . . . . . . . . . . . 26
Operating elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Total Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
HistoROM®/M-DAT (optional) . . . . . . . . . . . . . . . . . . . . . . . . . 12 Warm-up period – PMD70, FMD76 . . . . . . . . . . . . . . . . . . . . . 26
Functional Safety SIL/IEC 61508 Declaration of conformity (optional) Influence of the operating pressure on zero point and span – PMD70,
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 FMD76 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
On-site operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Thermal change of the zero output and the output span – PMD70,
Handheld terminals – HART . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 FMD76 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Handheld terminal DXR375 – FOUNDATION Fieldbus . . . . . . . 12
FieldCare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Operating conditions (Installation) . . . . . . . . . . . . . . 27
Remote operation – FOUNDATION Fieldbus . . . . . . . . . . . . . . . 13 General installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . 27
Commubox FXA291 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Measuring arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
ToF Adapter FXA291 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Heat insulation – FMD77 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Wall- and pipe-mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 "Separate housing" version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Measured variable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Turn the housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Measuring range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Oxygen applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Explanation of terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Ultra pure gas applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Diaphragms for materials with hydrogen build-up (Gold-Rhodium
coating) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Output signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Signal range – 4...20 mA HART . . . . . . . . . . . . . . . . . . . . . . . . . 16 Operating conditions (Environment) . . . . . . . . . . . . . 31
Signal on alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Ambient temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Load – 4...20 mA HART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Degree of protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Dynamic behavior current output . . . . . . . . . . . . . . . . . . . . . . . . 17 Climate class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Dynamic behavior HART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Vibration resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Dynamic behavior PROFIBUS PA . . . . . . . . . . . . . . . . . . . . . . . . 18 Electromagnetic compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Dynamic behavior FOUNDATION Fieldbus . . . . . . . . . . . . . . . . 19 Overvoltage protection (optional) . . . . . . . . . . . . . . . . . . . . . . . . 31
Damping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Operating conditions (Process) . . . . . . . . . . . . . . . . . 32
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Process temperature limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Process temperature range, seals . . . . . . . . . . . . . . . . . . . . . . . . 32
Supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Pressure specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Current consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Cable entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Mechanical construction . . . . . . . . . . . . . . . . . . . . . . 34
Cable specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Housing dimensions T14, optional display on the side . . . . . . . . . 34
Residual ripple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Housing dimensions T15, optional display on the top . . . . . . . . . 34
Influence of power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Housing dimensions T17, optional display on the top . . . . . . . . . 34
Process connections PMD70 with ceramic measuring
Performance characteristics – general . . . . . . . . . . . . 23 diaphragms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Reference operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Process connections PMD70 with ceramic measuring
Long-term stability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 diaphragms (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Influence of the installation position . . . . . . . . . . . . . . . . . . . . . . 23 Process connections PMD75 with metallic measuring
Vibration effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 diaphragms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Process connections PMD75 with metallic measuring
diaphragms (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Performance characteristics – metallic diaphragms . . 24 Process connections PMD75 with metallic measuring
Reference accuracy – PMD75, FMD77, FMD78 . . . . . . . . . . . . . 24 diaphragms (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Total performance – PMD75 . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Process connection FMD76 with ceramic measuring

2 Endress+Hauser
 Deltabar S

diaphragms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 FMD78 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Process connection FMD76 with ceramic measuring FMD78 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
diaphragms (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Process connection FMD76 with ceramic measuring
Further documentation . . . . . . . . . . . . . . . . . . . . . . . 81
diaphragms (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Innovation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Process connections FMD77 with metallic measuring
Field of Activities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
diaphragms, low-pressure side . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Process connections FMD77 with metallic measuring
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
diaphragms, high-pressure side . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Brief operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Process connections FMD77 with metallic measuring
Manual for Functional Safety (SIL) . . . . . . . . . . . . . . . . . . . . . . . 81
diaphragms, high-pressure side (continued) . . . . . . . . . . . . . . . . 44
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Process connections FMD77 with metallic measuring
Installation/Control Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . 82
diaphragms, high-pressure side (continued) . . . . . . . . . . . . . . . . 45
Overspill protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
FMD78 Basic unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Process connection FMD78 with metallic measuring
diaphragms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Process connection FMD78 with metallic measuring
diaphragms (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Process connection FMD78 with metallic measuring
diaphragms (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Process connection FMD78 with metallic measuring
diaphragms (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Process connection FMD78 with metallic measuring
diaphragms (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Process connection FMD78 with metallic measuring
diaphragms (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Process connection FMD78 with metallic measuring
diaphragms (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
"Separate housing" version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Planning instructions, diaphragm seal systems . . . . . 57

Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Design and operation mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Diaphragm seal filling oils . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Influence of the temperature on the zero point . . . . . . . . . . . . . . 59
Ambient temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Response time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Certificates and approvals . . . . . . . . . . . . . . . . . . . . . 66

CE mark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Ex approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Marine certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Overspill protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
CRN approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Pressure Equipment Directive (PED) . . . . . . . . . . . . . . . . . . . . . 66
Standards and guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Ordering information . . . . . . . . . . . . . . . . . . . . . . . . 67
PMD70 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
PMD70 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
PMD75 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
PMD75 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
PMD75 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
FMD76 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
FMD76 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
FMD76 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
FMD77 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
FMD77 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
FMD77 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
FMD78 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

3 Endress+Hauser
 Deltabar S

Function and system design

Device selection

Deltabar S – PMD70 PMD75 FMD76 FMD77 FMD78

product family

+ –

+ –

P01-PMD70xxx-16-xx-xx-xx-000 P01-PMD75xxx-16-xx-xx-xx-000 P01-FMD76xxx-16-xx-xx-xx-000 P01-FMD77xxx-16-xx-xx-xx-000 P01-FMD78xxx-16-xx-xx-xx-003

With ceramic measuring With metallic measuring With ceramic With metallic With metallic measuring
diaphragms diaphragms measuring diaphragms measuring diaphragms diaphragms and
and diaphragm seal capillary diaphragm
mounted on one side seals
Field of – Flow – Flow – Level – Level – Level
application – Level – Level – Differential pressure
– Differential pressure – Differential pressure
Process – 1/4 – 18 NPT – 1/4 – 18 NPT Low-pressure side (–): Low-pressure side (–): – Wide range of
connections – RC 1/4 – RC 1/4 – 1/4 – 18 NPT – 1/4 – 18 NPT diaphragm seals,
– RC 1/4 – RC 1/4 → see page 5, section
"Overview of diaphragm
High-pressure side (+): High-pressure side (+):
– DN 80 – DN 100 – DN 50 – DN 100 seal FMD78"
– ANSI 3" – 4" – ANSI 2" – 4"
– JIS 80A – 100A – JIS 80A – 100A
Measuring ranges from –25...+25 mbar from –10...+10 mbar from –100...+100 mbar from –100...+100 mbar from –100...+100 mbar
to –3...+3 bar to –40...+40 bar to –3...+3 bar to –16 bar...+16 bar to –40...+40 bar
Overload 1 on one side: max. 100 bar on one side: max. 420 bar on one side: max. 100 bar on one side: max. 160 bar on one side: max. 160 bar
on both sides: max. 150 bar on both sides: max. 630 bar on both sides: max. 240 bar
Process –20...+85°C –40...+120°C –20...+85°C up to + 400°C (+752°F) up to +400°C (+752°F)
temperature range (–4...+185°F) (–40...+248°F) (–4...+185°F)
Ambient –20...+85°C –40...+85°C –20...+85°C –40...+85°C –40...+85°C
temperature range (–4...+185°F) (–40...+185°F) 2 (–4...+185°F) (–40...+185°F) 2 (–40...+185°F) 2
Ambient –40 to +60°C (–40 to +140°F)
temperature range
separate housing
Reference – Up to ±0.075% of the set span – Up to ±0.075 % of the set span
Accuracy – PLATINUM version: up to ±0.05% of the set span
Supply voltage – For non-hazardous areas: 10.5...45 V DC
– EEx ia: 10.5...30 V DC
Output 4...20 mA with superimposed HART protocol, PROFIBUS PA or FOUNDATION Fieldbus
Options – High-pressure version up to pstat 700 bar
– PMD75, FMD77, FMD78: Gold-Rhodium-coated diaphragm, NACE-compliant materials
Specialities – Metal-free measurement – pstat up to 420 bar – Abrasion-resistant and – For high media – Wide range of
(options) with PVDF flange – Diaphragm: tantalum corrosion-resistant temperatures diaphragm seals
– Available with Deltatop/ – Available with Deltatop/ – No diaphragm-seal
Deltaset as flow compact Deltaset as flow compact temperature effects
device device – Metal-free
measurement possible
with ECTFE-coated
process connection
– HistoROM®/M-DAT memory module

1) dependent on the lowest-rated element, with regard to pressure, of the selected components
2) lower temperature on request

4 Endress+Hauser
Deltabar S

Overview of diaphragm seal

FMD78
Design Diaphr. seal Connection Version Standard Nominal diameter Nom. press./Class

Cell Membrane DIN cell DIN 2501 – DN 50 PN 16 – 400

diaphragm seal – DN 80
(MDM) – DN 100

ANSI cell P01-FMD78xxx-04-xx-xx-xx-000 ANSI B 16.5 – 2" 150 – 2500 lbs

– 3"
– 4"
Threaded Membrane G ISO 228 G 1/2 B PN 40
connection with diaphragm seal
separator (MDM)
P01-FMD78xxx-03-xx-xx-xx-010

NPT ANSI 1/2 NPT PN 40

P01-FMD78xxx-03-xx-xx-xx-011

Tri-Clamp Membrane Clamp ISO 2852 – DN 25 (1") Dependent on the

diaphragm seal – DN 38 (1 1/2") clamp used
(MDM) – DN 51 (2")
– DN 76.1 (3")
P01-FMD78xxx-03-xx-xx-xx-005

Pipe diaphragm Clamp ISO 2852 – DN 25 (1") Dependent on the

seal (RDM) – DN 38 (1 1/2") clamp used
– DN 51 (2")
P01-FMD78xxx-03-xx-xx-xx-009

Hygienic Membrane Varivent Type N for pipes PN 40

connections diaphragm seal (EHEDG and 3A DN 40 – DN 162
(MDM) approval)
P01-FMD78xxx-03-xx-xx-xx-007

DRD DN50 (65 mm) 25 bar

P01-FMD78xxx-03-xx-xx-xx-006

Sanitary tank spud d = 100 mm Dependent on the

with 2" extended clamp used
diaphragm seal
P01-FMD78xxx-03-xx-xx-xx-008

Taper adapter with DIN 11851 – DN 50 PN 25

coupling nut – DN 65
– DN 80
P01-FMD78xxx-03-xx-xx-xx-003

Threaded adapter DIN 11851 – DN 50 PN 25

– DN 65
– DN 80
P01-FMD78xxx-03-xx-xx-xx-004

Endress+Hauser 5
 Deltabar S

Design Diaphr. seal Connection Version Standard Nominal diameter Nom. press./Class

Flange Membrane EN/DIN flange EN 1092-1/ – DN 50 Up to 40 bar

diaphragm seal DIN 2527 – DN 80
(MDM) – DN 100

ANSI flange P01-FMD78xxx-03-xx-xx-xx-001 ANSI B 16.5 – 2" 150 lbs and

– 3" 300 lbs
– 4"

JIS flange B 2220 – 50 A 10 K

– 80 A
– 100 A

Flange with Membrane ANSI flange ANSI B 16.5 – 3" with 2"/4"/6"/ 150 lbs
extended diaphragm seal 8" extended
diaphragm seal (MDM) diaphragm seal
– 4" with 2"/4"/6"/
P01-FMD78xxx-03-xx-xx-xx-002
8" ext. diaphr. seal

6 Endress+Hauser
Deltabar S

Measuring principle

Ceramic measuring diaphragms used for PMD70 Metallic measuring diaphragms used for PMD75, FMD77 and FMD78
and FMD76

➀
➀ ➁
➁ ➆
➅
p1 p2
➂ ➇
➂ p1 ➃ p2 p1 p2
➈
➃ ➄
➄
P01-xMD7xxxx-03-xx-xx-xx-000 P01-xMD7xxxx-03-xx-xx-xx-002 P01-xMD7xxxx-03-xx-xx-xx-003

Ceramic measuring cell PMD70 and FMD76 Metal measuring cell 10 mbar and 30 mbar Metal measuring cell as of 100 mbar
1 Meter body 1 Sensing element 6 Sensing element
2 Diaphragm 2 Silicon diaphragm 7 Overload diaphragm/Middle diaphragm
3 Electrodes 3 Separating diaphragm 8 Filling oil
4 Glass frit fixes the diaphragm onto the meter 4 Filling oil 9 Separating diaphragm
body 5 Integrated overload protection
5 Temperature sensor

Ceramic measuring diaphragms used for PMD70 and FMD76

The ceramic measuring cell is based on the principle of a plate capacitor with an electrode on (1) and a movable
electrode on the interior of the diaphragm (3). Standard silicone oil or mineral oil filling oils for this measuring
cell.
A differential pressure (p1 ≠ p2) causes a corresponding deflection of both diaphragms. Both capacitance values
are converted and are fed to the microprocessor of the transmitter as a digital signal.
Advantages:
• Self-monitoring for diaphragm break or oil loss (constant comparison of the measured temperature with a
temperature calculated from the capacitance values)
• Extremely high resistance to aggressive media
• Suitable for vacuums up to 1 mbarabs
• Metal-free versions available
• Second process barrier (Secondary Containment) for enhanced integrity

Metallic measuring diaphragms used for PMD75, FMD77 and FMD78

The separating diaphragms (3/9) are deflected on both sides by the acting pressures. A filling oil (4/8) transfers
the pressure to a resistance circuit bridge (semi-conductor technology). The differential-pressure-dependent
change of the bridge output voltage is measured and further processed.
Advantages:
• Standard operating pressures: 160 bar and 420 bar
• High long-term stability
• Very high single-sided overload resistance
• Second process barrier (Secondary Containment) for enhanced integrity

Endress+Hauser 7
 Deltabar S

Flow measurement Design and operation mode

+ – + –
Q ~ Δp p1 p2 Q ~ Δp p1 p2

Q Q

P01-PMD7xxxx-15-xx-xx-xx-000

Flow measurement with Deltabar S and primary element, left: Orifice plate and right: Pitot tube
Q Flow
Δp Differential pressure, Δp = p1 – p2

Your benefits
• Choice of four flow modes of operation: volume flow, norm volume flow (European norm conditions),
standard volume flow (American standard conditions) and mass flow.
• Choice of diverse flow units with automatic unit conversion.
• A customised unit can be specified
• Low flow cut off: when activated, this function suppresses small flows which can lead to large fluctuations
in the measured value.
• Contains two totalizers as standard. One totalizer can be reset to zero.
• The totalizing mode and unit can be individually set for each totalizer. This allows independent daily and
annual quantity totalizing.
• With the product families Deltatop and Deltaset, Endress+Hauser is offering two universal and reliable
solutions for flow measurement:
– Deltatop, the compact, ready-to-use flow measuring unit including differential pressure transmitter
Deltabar S
– Deltaset with differential pressure transmitter Deltabar S, the modular flow measuring unit suitable for
medium temperatures up to 1000°C (1832°F) and pressures up to 400 bar

Note: For more information about flow measurement with the Deltabar S differential pressure transmitter
and orifice plate or pitot tube, see Technical Information TI297P Deltatop/Deltaset.

8 Endress+Hauser
Deltabar S

Level measurement (level, Design and operation mode

volume and mass)

– – Δp
h= ρ g

➀
h
➂
➁ +

+
P01xMD7xxxx-15-xx-xx-xx-000

Level measurement with Deltabar S

1 Level measurement via impulse piping and PMD70
2 Level measurement with FMD76
3 Level measurement with FMD78
h Height (level)
Δp Differential pressure
ρ Density of the medium
g Gravitation constant

Your benefits
• Choice of three level operating modes
• Volume and mass measurements in any tank shapes by means of a freely programmable characteristic curve
• Choice of diverse level units with automatic unit conversion
• A customised unit can be specified
• Has a wide range of uses, e.g.
– for level measurement in tanks with superimposed pressure
– in the event of foam formation
– in tanks with agitators of screen fittings
– in the event of liquid gases
– for standard level measurement

Communication protocol • 4...20 mA with HART communication protocol

• PROFIBUS PA
– The Endress+Hauser devices meet the requirements as per the FISCO model.
– Due to the low current consumption of 11 mA ± 1 mA
– up to 9 Deltabar S for EEx ia, CSA IS and FM IS applications
– up to 32 Deltabar S for all other applications, e.g. in non-hazardous areas, EEx nA, etc.
can be operated at one bus segment with installation as per FISCO.
Further information on PROFIBUS PA, such as requirements for bus system components, can be found in
the Operating Instructions BA034S "PROFIBUS DP/PA: Guidelines for planning and commissioning" and in
the PNO guideline.
• FOUNDATION Fieldbus
– The Endress+Hauser devices meet the requirements as per the FISCO model.
– Due to the low current consumption of 14 mA ± 1 mA
– up to 7 Deltabar S for EEx ia, CSA IS and FM IS applications
– up to 30 Deltabar S for all other applications, e.g. in non-hazardous areas, EEx nA, etc.
can be operated at one bus segment with installation as per FISCO.
Further information on FOUNDATION Fieldbus, such as requirements for bus system components can be
found in the Operating Instructions BA013S "FOUNDATION Fieldbus Overview".

Endress+Hauser 9
 Deltabar S

Human interface
On-site display (optional) A 4-line liquid crystal display (LCD) is used for display and operation. The on-site display shows measured
values, dialog text as well as fault and notice messages in plain text, thereby supporting the user in every stage
of operation.

4...20 mA HART and PROFIBUS PA

Functions:
• 8-digit measured value display including sign and decimal point, bar graph for 4 to 20 mA HART as current
display or for PROFIBUS PA as graphical display of the scaled value of the AI Block
• Simple and complete menu guidance thanks to separation of the parameters into three levels
• Each parameter is given a 3-digit ID number for easy navigation.
• Option for configuring the display according to individual requirements and desires, such as language,
alternating display, display of other measured values such as sensor temperature, contrast setting
• Comprehensive diagnostic functions (fault and warning message, peak-hold indicators, etc.)
• rapid and safe commissioning with the Quick Setup menus

Measured value display Parameter

Identification
Function name Value number

Header line
Main line
Unit
Information
line
– + E Symbol
Bargraph
Editing modes

Operating keys
Selection
options

Value that
can be edited

Current measured value

P01-xMx7xxxx-07-xx-xx-xx-001

FOUNDATION Fieldbus
Functions:
• 8-digit measured value display including sign and decimal point, bargraph for current display
• Option for configuring the display according to individual requirements and desires, such as language,
alternating display, display of other measured values such as sensor temperature, contrast setting
• Comprehensive diagnostic functions (fault and warning message)

Measured value display Parameter

Identification
Function name Value number

Header line
Main line
Unit
Information
line
Symbol
Bargraph

P01-xMD7xxxx-07-xx-xx-xx-001

10 Endress+Hauser
Deltabar S

Operating elements With regard to T14 and T15 housings, the operating keys are located either outside the device under the
protection cap or inside on the electronic insert. In T17 housings, the operating keys are always located inside
on the electronic insert.
In addition, devices with an on-site display and a 4 to 20 mA HART or PROFIBUS PA electronic insert have
operating keys on the on-site display.

Operating keys on the exterior of the device

4...20 mA HART

PROFIBUS PA/
FOUNDATION Fieldbus

0%
Zero

P01-xxxxxxxx-19-xx-xx-xx-038

The operating keys located externally on the device work on the Hall sensor principle. As a result, no additional
openings are required in the device. This guarantees:
• Complete protection against environmental influences such as moisture and contamination
• Simple operation without any tools
• No wear.

Operating keys and elements located internally on the electronic insert

➃➄ ➅➆ ➄➅
t ➅ t
Sim.

on
➀ on
➀ ➁ ➂ on
➀ ➁ ➂
➁ ➃
off off 0% off 1 2
➃
0%

Sensor
Zero
Display ➄ Sensor
Zero
Display
Simulation

➂ on on ON CK S D A 0 8

on
HW

1 2 1 2 off off 1 2 3 4 5 6 7 8
PC

1 2 off
PC

PC
1 2 3 4 5 6 7 8
Address
Histo ROM

SW Histo ROM
HW
HART
R
250002271-–

TM
250002272-–

250002273-–

FIELD COMMUNICATION PROTOCOL

HW-Version: 1 FOUNDATION
SW-Version: 2 HW-Version: 1 HW-Version: 1
SW-Version: 2 SW-Version: 2

P01-xxxxxxxx-19-xx-xx-xx-104 P01-xxxxxxxx-19-xx-xx-xx-105 P01-xxxxxxxx-19-xx-xx-xx-106

Electronic insert HART Electronic insert PROFIBUS PA Electronic insert FOUNDATION Fieldbus
1 Operating keys 1 Green LED to indicate value being accepted 1 Green LED to indicate value being accepted
2 Slot for optional display 2 Key for position calibration and device reset 2 Key for position calibration
3 Slot for optional HistoROM®/M-DAT 3 DIP-switch for bus address 3 Slot for optional display
4 DIP-switch for locking/unlocking measured- 4 Slot for optional display 4 Slot for optional HistoROM®/M-DAT
value-relevant parameters 5 Slot for optional HistoROM®/M-DAT 5 DIP-switch for locking/unlocking measured-
5 DIP-switch for damping on/off 6 DIP-switch for locking/unlocking measured- value-relevant parameters
6 Green LED to indicate value being accepted value-relevant parameters 6 DIP-switch for simulation mode on/off
7 DIP-switch for damping on/off

Endress+Hauser 11
 Deltabar S

HistoROM®/M-DAT HistoROM®/M-DAT is a memory module, which is attached to the electronic insert. The HistoROM®/M-DAT
(optional) can be retrofitted at any stage (Order number: 52027785).

Your benefits
• Quick and safe commissioning of the same measuring points by copying the configuration data of one
transmitter to another transmitter
• Reliable process monitoring thanks to cyclical recording of pressure and sensor temperature measured values
• Simple diagnosis by recording diverse events such as alarms, configuration changes, counters for measuring
range undershoot and overshoot for pressure and temperature as well as user limit overshoot and undershoot
for pressure and temperature etc.
• Analysis and graphic evaluation of the events and process parameters via software (contained in scope of
supply).
HistoROM®/M-DAT can be ordered via feature 100 "Additional options 1" or feature 110 "Additional
options 2" or as spare parts. → See also page 67 ff. A CD with the Endress+Hauser operating program is also
included in the scope of delivery.

You can copy data from one transmitter to another transmitter when operating a FOUNDATION Fieldbus
device via an FF configuration program. You need the Endress+Hauser FieldCare operating program and the
Commubox FXA291 service interface and the ToF Adapter FXA291 to be able to access the data and events
saved in the HistoROM®/M-DAT.

Functional Safety SIL/ The Deltabar S differential pressure transmitters with 4...20 mA output signal have been developed to
IEC 61508 Declaration of IEC 61508 standard and have been certified by TÜV SÜD. These devices can be used for flow and differential
conformity (optional) pressure monitoring up to SIL3.
→ For a detailed description of the safety functions with Deltabar S, settings and characteristic quantities for
functional safety, please refer to the "Manual for Safety Manual - Deltabar S" SD189P.
→ For devices with SIL2/IEC 61508 declaration of conformity, see page 68 ff, Feature 100 "Additional
option 1" and Feature 110 "Additional option 2", version E "SIL2/IEC 61508, Declaration of Conformity".

On-site operation Functions 4...20 mA HART and PROFIBUS PA

• With on-site display: navigate through the operating menu using three operating keys
• Without on-site display:
– Position calibration (zero point correction)
– Setting lower-range value and upper-range value – reference pressure present at device (HART only)
– Value acceptance indicated by green LED
• Device reset
• Locking and unlocking measured-value-relevant parameters
• Switching damping on and off
• Setting bus address (PROFIBUS PA only)

Functions FOUNDATION Fieldbus

• Position calibration (zero point correction)
• Value acceptance indicated by green LED
• Locking and unlocking measured-value-relevant parameters
• Switching simulation mode on and off

Handheld terminals – HART With a handheld terminal, all the parameters can be configured anywhere along the 4...20 mA line via menu
operation.

Handheld terminal DXR375 – With a handheld terminal DXR375, all the parameters can be configured via menu operation.
FOUNDATION Fieldbus

12 Endress+Hauser
Deltabar S

FieldCare FieldCare is an Endress+Hauser asset management tool based on FDT technology. With FieldCare, you can
configure all Endress+Hauser devices as well as devices from other manufacturers that support the FDT
standard. The following operating systems are supported: WinNT4.0, Win2000 and Windows XP.
FieldCare supports the following functions:
• Configuration of transmitters in offline and online operation
• Loading and saving device data (upload/download)
• HistoROM®/M-DAT analysis
• Documentation of the measuring point
Connection options:
• HART via Commubox FXA191 and the RS 232 C serial interface of a computer
• HART via Commubox FXA195 and the USB port on a computer
• PROFIBUS PA via segment coupler and PROFIBUS interface card
• Service interface with adapter Commubox FXA291 and ToF Adapter FXA291 (USB).

Remote operation – An FF configuration program is required to integrate a device with "FOUNDATION Fieldbus signal" into an FF
FOUNDATION Fieldbus network or to set the FF-specific parameters. Please contact your local Endress+Hauser Sales Center for more
information.

Commubox FXA291 The Commubox FXA291 connects Endress+Hauser field instruments with CDI interface (= Endress+Hauser
Common Data Interface) to the USB interface of a personal computer or a notebook. For details refer to
TI405C/07/en.

! Note!
For the following Endress+Hauser instruments you need the "ToF Adapter FXA291" as an additional accessory:
• Cerabar S PMC71, PMP7x
• Deltabar S PMD7x, FMD7x
• Deltapilot S FMB70

ToF Adapter FXA291 The ToF Adapter FXA291 connects the Commubox FXA291 via the USB interface of a personal computer or
a notebook. For details refer to KA271F/00/a2.

Endress+Hauser 13
 Deltabar S

Input
Measured variable Differential pressure, from which flow (volume or mass current) and level (level, volume or mass) are derived

Measuring range PMD75, FMD77, FMD78 (with metallic measuring diaphragms)

Nominal Measurement Smallest MWP 1 Overload 2 Min. operating pressure 3 Versions in the
value limit calibratable order code 4
span 5

lower upper on one side on both sides PN 160 6 PN 420 6

(LRL) (URL)

[mbar] [mbar] [mbar] [mbar] [bar] [bar] [bar] [mbarabs]

7
10 –10 +10 0.25 160 160 240 0.1 7B –

30 7 –30 +30 0.3 160 160 240 0.1 7C –

8
100 –100 +100 1/5 160 160 240 0.1 7D –
9
500 –500 +500 5 160/420 160/420 240/630 0.1 7F 8F

3000 –3000 +3000 30 160/420 9 160/420 240/630 0.1 7H 8H

9
16000 –16000 +16000 160 160/420 160/420 240/630 0.1 7L 8L
9
40000 –40000 +40000 400 160/420 "+"side: 240/630 0.1 7M 8M
160/420 10

PMD70, FMD76 (with ceramic measuring diaphragms)

Nominal Measurement Smallest MWP 1 Overload 2 Min. operating pressure 3 Versions in the
value limit calibratable order code 4
span 5

lower upper on one side on both sides

(LRL) (URL)

[mbar] [mbar] [mbar] [mbar] [bar] [bar] [bar] [mbarabs]

25 –25 +25 0.25 10 10 15 1 7B

100 –100 +100 1 16 16 24 1 7D

500 –500 +500 5 100 100 150 1 7F

3000 –3000 +3000 30 100 100 150 1 7H

1) The MWP (maximum working pressure; MWP = PN) for the measuring device depends on the weakest element of the components selected with regard to
pressure, i.e. the process connection (→ see page 34 ff) has to be taken into consideration in addition to the measuring cell (→ see table above). Also observe
pressure-temperature dependency. For the appropriate standards and further information, see page 33, "Pressure specifications" section.
2) The maximum pressure for the measuring device is dependent on the lowest-rated element, with regard to pressure, of the selected components. → See also
page 33, section "Pressure specifications".
3) The minimum operating pressure indicated in the table applies to silicone oil under reference operating conditions.
Min. operating pressure at 85°C (185°F) for silicone oil: 10 mbarabs.
FMD77 and FMD78: Min. operating pressure: 50 mbarabs; observe also the pressure and temperature application limits of the selected filling oil on page 58.
For vacuum applications, please observe the installation instructions on Page 65 ff.
4) Versions in the order code → See also page 70 ff, feature 40 "Nominal range; PN"
5) Turn down > 100:1 on request
6) PN 160 versions with stainless steel A2 screws, PN 420 versions with stainless steel A4 M12 screws
PN 420 versions for PMD75 only.
7) PMD75 only
8) minimum span that can be calibrated for PMD75: 1 mbar; minimum span that can be calibrated for FMD77 and FMD78: 5 mbar
9) For PMD75 with CRN-approved process connections, the MWP is 315 bar.
10) "–" side: 100 bar

14 Endress+Hauser
Deltabar S

Explanation of terms Explanation of the terms: Turn down (TD), set span and zero based span

Case 1:
• ⏐Lower range value⏐ ≤ ⏐Upper range value⏐
Example:
• Lower range value (LRV) = 0 mbar
• Upper range value (URV) = 100 mbar
• Nominal value (URL) = 500 mbar
Turn down:
• TD = URL / ⏐URV⏐ = 5:1
set span:
• URV – LRV = 100 mbar
This span is based on the zero point.
P01-xxxxxxxx-05-xx-xx-xx-001

Example: 500 mbar sensor

Case 2:
• ⏐Lower range value⏐ ≥ ⏐Upper range value⏐
Example:
• Lower range value (LRV) = –300 mbar
• Upper range value (URV) = 0 bar
• Nominal value (URL) = 500 mbar
Turn down:
• TD = URL / ⏐(LRV)⏐ = 1,67:1
set span:
• URV – LRV = 300 mbar
This span is based on the zero point.
P01-xMD7xxxx-05-xx-xx-xx-007

Example: 500 mbar sensor

1 Set span
2 Zero based span
3 Nominal value i Upper range limit (URL)
4 Nominal measuring range
5 Sensor measuring range
LRL Lower range limit
URL Upper range limit
LRV Lower range value
URV Upper range value

Endress+Hauser 15
 Deltabar S

Output
Output signal • 4...20 mA with superimposed digital communication protocol HART 5.0, 2-wire
• Digital communication signal PROFIBUS PA (Profile 3.0)
• Digital communication signal FOUNDATION Fieldbus

Signal range – 3.8 mA to 20.5 mA

4...20 mA HART

Signal on alarm • 4...20 mA HART

Options:
– Max. alarm*: can be set from 21...23 mA
– Keep measured value: last measured value is kept
– Min. alarm: 3.6 mA
* Factory setting: 22 mA
• PROFIBUS PA: can be set in the Analog Input block,
options: Last Valid Out Value, Fsafe Value (factory setting), Status bad
• FOUNDATION Fieldbus: can be set in the Analog Input Block,
options: Last Good Value, Fail Safe Value (factory setting), Wrong Value

Load – 4...20 mA HART

➀ RLmax ➁ RLmax
[Ω] [Ω]
Test 1500 Test
1456
1282 1239

847 804
➃ ➃
413
➂ 369
➂

10.5 20 30 40 45 U 11.5 20 30 40 45 U
[V] [V]

U – 10.5 V U – 11.5 V
RLmax ≤ RLmax ≤
23 mA 23 mA
P01-xMD7xxxx-05-xx-xx-xx-000

Load diagram, observe the position of the jumper and the explosion protection (→ See also page 22, section "Taking 4...20
mA test signal".)
1 Jumper for 4...20 mA test signal inserted in "Non-test" position
2 Jumper for 4...20 mA test signal inserted in "Test" position
3 Supply voltage 10,5 (11,5)...30 V DC for 1/2 D, 1 GD, 1/2 GD, FM IS, CSA IS, IECEx ia, NEPSI Ex ia
4 Supply voltage 10,5 (11,5)...45 V DC for device for non-hazardous areas, 1/2 D, 1/3 D, 2 G EEx d, 3 G EEx nA,
FM XP, FM DIP, FM NI, CSA XP, CSA Dust-Ex, NEPSI Ex d
RLmax Maximum load resistance
U Supply voltage

Note!
When operating via a handheld terminal or via PC with an operating program, a minimum communication
resistance of 250 Ω must exist within the loop.

Resolution • Current output: 1 μA

• Display: can be set (setting at the factory: presentation of the maximum accuracy of the transmitter)

16 Endress+Hauser
Deltabar S

Dynamic behavior Dead time, Time constant (T63)

current output

100 %

63 %

t1 t2 t
P01-xxxxxxxx-05-xx-xx-xx-007

Presentation of the dead time and the time constant

Type Dead time t1 Time constant (T63), t2

PMD75 45 ms • 10 mbar and 30 mbar measuring cell: 200 ms

• 100 mbar measuring cell: 60 ms
• 500 mbar measuring cell: 45 ms
• 3 bar measuring cell: 40 ms
• 16 bar and 40 bar measuring cell: 60 ms

FMD77, FMD78 dependent on the diaphragm seal

PMD70, FMD76 90 ms • 25 mbar measuring cell: 4700 ms
• 100 mbar measuring cell: 280 ms
• 500 mbar measuring cell: 210 ms
• 3 bar measuring cell: 110 ms

Dynamic behavior HART Dead time, Time constant (T63)

A typical cyclic parametrization for the PLC of 20 values per second results in the following total dead time:

Type Dead time t1 Time constant (T63), t2

PMD75 295 ms • 10 mbar and 30 mbar measuring cell: 200 ms

• 100 mbar measuring cell: 60 ms
• 500 mbar measuring cell: 45 ms
• 3 bar measuring cell: 40 ms
• 16 bar and 40 bar measuring cell: 60 ms

FMD77, FMD78 dependent on the diaphragm seal

PMD70, FMD76 340 ms • 25 mbar measuring cell: 4700 ms

• 100 mbar measuring cell: 280 ms
• 500 mbar measuring cell: 210 ms
• 3 bar measuring cell: 110 ms

Reading cycle
• HART commands: on average 3 to 4 per second

Cycle time (Update time)

On average 250...330 ms.

Response time
≤ 250 ms

Endress+Hauser 17
 Deltabar S

Dynamic behavior Dead time, Time constant (T63)

PROFIBUS PA
A typical cyclic parametrization for the PLC of 20 values per second results in the following total dead time:

Type Dead time t1 Time constant (T63), t2

PMD75 295 ms • 10 mbar and 30 mbar measuring cell: 200 ms

• 100 mbar measuring cell: 60 ms
• 500 mbar measuring cell: 45 ms
• 3 bar measuring cell: 40 ms
• 16 bar and 40 bar measuring cell: 60 ms

FMD77, FMD78 dependent on the diaphragm seal

PMD70, FMD76 340 ms • 25 mbar measuring cell: 4700 ms

• 100 mbar measuring cell: 280 ms
• 500 mbar measuring cell: 210 ms
• 3 bar measuring cell: 110 ms

Reading cycle
cyclic:
• max.: 100/s
• typical value: 20/s
acyclic:
• max.: 20/s
• typical value: 10/s

Cycle time (Update time)

• The cycle time in a bus segment in cyclic data communication depends on the number of devices, on the
segment coupler used and on the internal PLC cycle time.
• The minimum cycle time is approx. 20 ms per device.

Response time
• cyclic: approx. 10 ms per request
• acyclic: < 50 ms
All values are typical values.

18 Endress+Hauser
Deltabar S

Dynamic behavior Dead time, Time constant (T63)

FOUNDATION Fieldbus
If the macro cycle time (of the PLC) is set to a typical value of 250 ms, the following total dead time results:

Type Dead time t1 Time constant (T63), t2

PMD75 295 ms • 10 mbar and 30 mbar measuring cell: 200 ms

• 100 mbar measuring cell: 60 ms
• 500 mbar measuring cell: 45 ms
• 3 bar measuring cell: 40 ms
• 16 bar and 40 bar measuring cell: 60 ms

FMD77, FMD78 dependent on the diaphragm seal

PMD70, FMD76 340 ms • 25 mbar measuring cell: 4700 ms

• 100 mbar measuring cell: 280 ms
• 500 mbar measuring cell: 210 ms
• 3 bar measuring cell: 110 ms

Reading cycle
• cyclic: up to 5/s, dependent on the number and type of function blocks used in a closed-control loop
• acyclic: 10/s

Cycle time (Update time)

250 ms

Response time
• cyclic: < 80 ms
• acyclic: < 40 ms
All values are typical values.

Damping A damping affects all outputs (output signal, display).

• Via on-site display, handheld terminal or PC with operating program, continuous from 0...999 s
• Additionally for HART and PROFIBUS PA: via DIP-switch on the electronic insert, switch position
"on" = set value and "off"
• Factory setting: 2 s

Endress+Hauser 19
 Deltabar S

Power supply
Electrical connection Note!
• When using the measuring device in hazardous areas, installation must comply with the corresponding
national standards and regulations and the Safety Instructions or Installation or Control Drawings. → See
also page 81, section "Safety Instructions" and "Installation/Control Drawings".
• Devices with integrated overvoltage protection must be earthed. → See also page 31.
• Protective circuits against reverse polarity, HF influences and overvoltage peaks are installed.

4...20 mA HART

➀ ➅ 10.5 V DC
➆ 11.5 V DC

4…20 mA
Test

Test

➁ 4... 20mA Test

➂ ➄
➇
4... 20mA Test

➃
P01-xMx7xxxx-04-xx-xx-xx-001

Electrical connection 4...20 mA HART

1 Housing
2 Jumper for 4...20 mA test signal. → See also page 22, section "Taking 4...20 mA test signal" .
3 Internal earth terminal
4 External earth terminal
5 4...20 mA test signal between positive and test terminal
6 minimum supply voltage = 10.5 V DC, jumper is inserted in accordance with the illustration.
7 minimum supply voltage = 11.5 V DC, jumper is inserted in "Test" position.
8 Devices with integrated overvoltage protection are labelled OVP (overvoltage protection) here (→ see also page 31).

PROFIBUS PA
The two-wire cable must be connected to the "PA+" and "PA–" terminals.

FOUNDATION Fieldbus
The two-wire cable must be connected to the "FF+" and "FF–" terminals.

Devices with Harting plug Han7D

Deltabar S
+
7
+ – – 8 6
1
2 5
3 4
Han7D

+ –
P01-xMD7xxxx-04-xx-xx-xx-000

Left: electrical connection for devices with Harting plug Han7D

Right: view of the plug connector at the device

20 Endress+Hauser
Deltabar S

Devices with M12 plug

Deltabar S

+ –
– +

M12

+ –
P01-xMD7xxxx-04-xx-xx-xx-008

Left: electrical connection for devices with M12 plug

Right: view of the plug at the device

Endress+Hauser offers for devices with M12 plug the following accessories:
Plug-in jack M 12x1, straight
• Material: Body PA; coupling nut CuZn, nickel-plated
• Degree of protection (fully locked): IP67
• Order number: 52006263
Plug-in jack M 12x1, elbowed
• Material: Body PBT/PA; coupling nut GD-Zn, nickel-plated
• Degree of protection (fully locked): IP67
• Order number: 51006327
Cable 4x0.34 mm2 with M12 socket, elbowed, screw plug, 5 m length
• Material: Body PUR; coupling nut CuSn/Ni; cable PVC
• Degree of protection (fully locked): IP67
• Order number: 52010285

Devices with 7/8" plug

Deltabar S
–
+ –

7/8" +

+ –
P01-xMD7xxxx-04-xx-xx-xx-009

Left: electrical connection for devices with 7/8" plug

Right: view of the plug at the device

Endress+Hauser 21
 Deltabar S

Taking 4...20 mA test signal

A 4...20 mA signal may be measured via the positive and test terminal without interrupting the measurement.
The minimum supply voltage of the device can be reduced by simply changing the position of the jumper. As
a result, operation is also possible with lower voltage sources. Observe the position of the jumper in accordance
with the following table.

Jumper position for test signal Description

– Taking 4...20 mA test signal via plus and test terminal:

Test possible. (Thus, the output current can be measured without
interruption via the diode.)
– Delivery status
– minimum supply voltage: 11.5 V DC

– Taking 4...20 mA test signal via plus and test terminal:

Test not possible.
– minimum supply voltage: 10.5 V DC

Supply voltage Note!

• When using the measuring device in hazardous areas, installation must comply with the corresponding
national standards and regulations and the Safety Instructions or Installation or Control Drawings.
• All explosion protection data are given in separate documentation which is available upon request. The Ex
documentation is supplied as standard with all devices approved for use in explosion hazardous areas. → See
also page 81, sections "Safety Instructions" and "Installation/Control drawing".

4...20 mA HART
• Version for non-hazardous areas, jumper for 4...20 mA test signal in "Test" position (delivery status):
11.5...45 V DC
• Version for non-hazardous areas, jumper for 4...20 mA test signal in "Non-test" position: 10.5...45 V DC

PROFIBUS PA
• Version for non-hazardous areas: 9...32 V DC

FOUNDATION Fieldbus
• Version for non-hazardous areas: 9...32 V DC

Current consumption • PROFIBUS PA: 11 mA ± 1 mA, switch-on current corresponds to IEC 61158-2, Clause 21
• FOUNDATION Fieldbus: 14 mA ± 1 mA, switch-on current corresponds to IEC 61158-2, Clause 21

Cable entry → See also page 67 ff, feature 30 "Housing, Cable entry, Protection".

Cable specification • Endress+Hauser recommends using shielded, twisted-pair two-wire cables.

• Terminals for wire cross-sections 0.5...2.5 mm2
• Cable external diameter: 5...9 mm

Residual ripple Without influence on 4...20 mA signal up to ± 5 % residual ripple within the permitted voltage range [according
to HART hardware specification HCF_SPEC-54 (DIN IEC 60381-1)]

Influence of power supply ≤ 0.0006% of URL/1 V

22 Endress+Hauser
Deltabar S

Performance characteristics – general

Reference operating • As per IEC 60770
conditions • Ambient temperature TU = constant, in the range of: +21...+33°C (+69.8...+91.4°F)
• Humidity ϕ = constant, in the range of: 5...80 % r.H
• Ambient pressure pU = constant, in the range of: 860...1060 mbar
• Position of the measuring cell: constant, in the range of: ±1°
• Input of LOW SENSOR TRIM and HIGH SENSOR TRIM for lower range value and upper range value
• Zero based span
• Membrane material
– PMD75: AISI 316L/1.4435, Alloy C276, Gold-Rhodium coated, Monel
– FMD77, FMD78: AISI 316L/1.4435
– PMD70, FMD76: Al2O3 (Aluminium-oxide-ceramic)
• Filling oil: silicone oil
• Side flanges material PMD75: AISI 316L/1.4435
• Supply voltage: 24 V DC ± 3 V DC
• Load with HART: 250 Ω

Long-term stability Measuring cells ≥ 500 mbar:

• ±0.05% of URL/year
• ±0.125% of URL/5 years
Measuring cells ≤ 100 mbar:
• ±0.18% of URL/year

Influence of the installation • PMD70, FMD76: ≤ 3 mbar 1, 3

position • PMD75: ≤ 4 mbar 1, 3
• FMD77: ≤ 32 mbar 2, 3

1) Device is rotated vertically to the membrane axis.

2) Device rotated vertically to the flange membrane.
3) The value is doubled for devices with inert oil.

Note!
Position-dependent zero shift can be corrected. → See also page 27, section "General installation instructions"
and page 63 ff, section "Installation instructions, Diaphragm seal systems".

Vibration effects Device Housing Test standard Vibration effects

PMD70/ optional on-site display on GL ≤ reference accuracy to
FMD76 the side (T14) 10...18 Hz: ±4 mm;
18...500 Hz: 5 g
PMD75 optional on-site display on IEC 61298-3 ≤ reference accuracy to
the side (T14) 10...60 Hz: ±0.35 mm;
60...2000 Hz: 5 g
PMD75 optional on-site display on
the top (T15)

Endress+Hauser 23
 Deltabar S

Performance characteristics – metallic diaphragms

Reference accuracy – The reference accuracy comprises the non-linearity according to limit point setting, hysteresis and
PMD75, FMD77, FMD78 non-reproducibility as per IEC 60770.

The following applies for the root-extracting characteristic curve:

The accuracy data of the Deltabar S is taken into the accuracy calculation of the flow rate with a factor of 0.5.

PMD75
10 mbar, 30 mbar measuring cells:
• TD 1:1: ±0.15% of the set span
• TD > 1:1: ±0.15% of the set span x TD
100 mbar measuring cell:
• TD 1:1 to TD 4:1: ±0.075% of the set span
• TD > 4:1: ±(0.012 x TD + 0.027)% of the set span
Measuring cells ≥ 500 mbar:
• TD 1:1 to TD 15:1: ±0.075% of the set span
• TD > 15:1: ±(0.0015 x TD + 0.053)% of the set span
Platinum version,
Measuring cells ≥ 100 mbar:
• TD 1:1: ±0.05 % of the set span

FMD77 (influence of the diaphragm seal included)

100 mbar measuring cell:
• TD 1:1 to TD 4:1: ±0.15% of the set span
• TD > 4:1: ±(0.03 x TD + 0.03)% of the set span
Measuring cells ≥ 500 mbar:
• TD 1:1 to TD 15:1: ±0.075% of the set span
• TD > 15:1: ±(0.0015 x TD + 0.053)% of the set span

FMD78 (influence of the diaphragm seal included)

100 mbar measuring cell:
• TD 1:1 to TD 4:1: ±0.15% of the set span
• TD > 4:1: ±(0.03 x TD + 0.03)% of the set span
Measuring cells ≥ 500 mbar:
• TD 1:1 to TD 4:1: ±0.15% of the set span
• TD > 4:1: ±(0,02 x TD + 0,07) % of the set span

Total performance – PMD75 The "Total performance" specification comprises the non-linearity including hysteresis, non-reproducibility, the
thermal change of the zero point as well as the influence of the line pressure (pst = 70 bar).
• AISI 316L/1.4435, Alloy, Gold-Rhodium coated or Monel membrane:
±0.15 % of the set span 1, 2
• Tantal membrane:
±0.30 % of the set span 1, 2

1. for measuring ranges ≥ 500 mbar to TD 2:1

2. All specifications apply to the temperature range –10...+60°C (+14...+140°F).

Total Error The total error comprises the long-term stability and the total performance:
AISI 316L/1.4435, Alloy, Gold-Rhodium coated or Monel membrane:
• 10 mbar, 30 mbar and 100 mbar measuring cell = 0,33% of URL/year
• ≥ 500 mbar measuring cell = 0,20% of URL/year
Tantal membrane:
• 10 mbar, 30 mbar and 100 mbar measuring cell = 0,48% of URL/year
• ≥ 500 mbar measuring cell = 0,35% of URL/year

24 Endress+Hauser
Deltabar S

Warm-up period – • 4...20 mA HART : < 10 s

PMD75, FMD77, FMD78 • PROFIBUS PA: 6 s
• FOUNDATION Fieldbus: 50 s

Influence of the operating Measuring AISI 316L/1.4435, Alloy, Gold-Rhodium Tantal membrane
pressure on zero point and cell coated or Monel membrane
span – PMD75, FMD77,
FMD78 Influence of the Influence of the Influence of the Influence of the
operating pressure on operating pressure on operating pressure on operating pressure on
the zero point the span the zero point the span

10 mbar ±0.15 % of URL/7 bar ±0.035 % of URL/7 bar ±0.28 % of URL/7 bar ±0.28 % of URL/7 bar
30 mbar ±0.35 % of URL/70 bar ±0.14 % of URL/70 bar ±0.70 % of URL/70 bar ±0.70 % of URL/70 bar

100 mbar ±0.15 % of URL/70 bar ±0.14 % of URL/70 bar ±0.42 % of URL/70 bar ±0.42 % of URL/70 bar

500 mbar ±0.075 % of URL/70 bar ±0.14 % of URL/70 bar ±0.14 % of URL/70 bar ±0.14 % of URL/70 bar

3 bar ±0.075 % of URL/70 bar ±0.14 % of URL/70 bar ±0.14 % of URL/70 bar ±0.14 % of URL/70 bar

16 bar ±0.075 % of URL/70 bar ±0.14 % of URL/70 bar ±0.14 % of URL/70 bar ±0.14 % of URL/70 bar

40 bar ±0.075 % of URL/70 bar ±0.14 % of URL/70 bar ±0.14 % of URL/70 bar ±0.14 % of URL/70 bar

Note!
The influence of the operating pressure on the zero point can be calibrated out.

Thermal change of the zero –10...+60°C (+14...+140°F)

output and the output AISI 316L/1.4435, Alloy, Gold-Rhodium coated or Monel membrane:
span -- PMD75 • 10 mbar, 30 mbar measuring cell: ±(0.31 x TD + 0.06)% of the set span
• 100 mbar measuring cell: ±(0.18 x TD + 0.02)% of the set span
• 500 mbar, 3 bar measuring cell: ±(0.08 x TD + 0.05)% of the set span
• 16 bar measuring cell: ±(0.1 x TD + 0.1)% of the set span
• 40 bar measuring cell: ±(0.08 x TD + 0.05)% of the set span
–10...+60°C (+14...+140°F)
Tantal membrane:
• 10 mbar, 30 mbar measuring cell: ±(0.31 x TD + 0.06)% of the set span
• 100 mbar measuring cell: ±(0.24 x TD + 0.06)% of the set span
• 500 mbar, 3 bar measuring cell: ±(0.08 x TD + 0.05)% of the set span
• 16 bar measuring cell: ±(0.1 x TD + 0.1)% of the set span
• 40 bar measuring cell: ±(0.08 x TD + 0.05)% of the set span
–40...–10°C, +60...+85°C (–40...+14°F, +140...+185°F)
all membrane materials:
• 10 mbar, 30 mbar measuring cell: ±(0.45 x TD + 0.1)% of the set span
• 100 mbar measuring cell: ±(0.3 x TD + 0.15)% of the set span
• 500 mbar, 3 bar measuring cell: ±(0.12 x TD + 0.1)% of the set span
• 16 bar measuring cell: ±(0.15 x TD + 0.2)% of the set span
• 40 bar measuring cell: ±(0.37 x TD + 0.1)% of the set span

Endress+Hauser 25
 Deltabar S

Performance characteristics – ceramic diaphragms

Reference accuracy – The reference accuracy comprises the non-linearity including hysteresis and non-reproducibility in accordance
PMD70, FMD76 with the limit point method as per IEC 60770.

The following applies for the root-extracting characteristic curve:

The accuracy data of the Deltabar S is taken into the accuracy calculation of the flow rate with a factor of 0.5.
25 mbar measuring cell:
• TD 1:1: ±0.15% of the set span
• TD > 1:1: ±0.15% of the set span x TD
100 mbar measuring cell:
• TD 1:1 to TD 4:1: ±0.075% of the set span
• TD > 4:1: ±(0.012 x TD + 0.027)% of the set span
500 mbar, 3 bar measuring cell:
• TD 1:1 to TD 15:1: ±0.075% of the set span
• TD > 15:1: ±(0.0015 x TD + 0.05252)% of the set span
Platinum version,
100 mbar, 500 mbar, 3bar measuring cells:
• TD 1:1: ±0.05 % of the set span

Total performance – The "Total performance" specification comprises the non-linearity including hysteresis, non-reproducibility, the
PMD70, FMD76 thermal change of the zero point as well as the influence of the line pressure (pst = 70 bar).
• ±0.15% of the set span 1, 2

1. for measuring ranges ≥ 500 mbar, TD 1:1

2. All specifications apply to the temperature range –10...+60°C (+14...+140°F).

Total Error The total error comprises the long-term stability and the total performance:
• 25 mbar and 100 mbar measuring cell = 0,33% of URL/year
• 500 mbar and 3 bar measuring cell = 0,20% of URL/year

Warm-up period – • 4...20 mA HART : < 10 s

PMD70, FMD76 • PROFIBUS PA: 6 s
• FOUNDATION Fieldbus: 50 s

Influence of the operating Measuring Influence of the Influence of the

pressure on zero point and cell operating pressure on operating pressure on
span – PMD70, FMD76 the zero point the span

25 mbar ±0.7 % of URL/7 bar ±0.14 % of URL/7 bar

100 mbar ±0.175 % of URL/70 bar ±0.14 % of URL/70 bar

500 mbar ±0.075 % of URL/70 bar ±0.14 % of URL/70 bar

3 bar ±0.075 % of URL/70 bar ±0.14 % of URL/70 bar

Note!
The influence of the operating pressure on the zero point can be calibrated out.

Thermal change of the zero –10...+60°C (+14...+140°F):

output and the output span – • 25 mbar measuring cell: ±(0.35 x TD + 0.05)% of the set span
PMD70, FMD76 • ≥100 mbar measuring cells: ±(0.05 x TD + 0.05)% of the set span
–20...–10°C, +60...+85°C (–4...+14°F, +140...+185°F):
• 25 mbar measuring cell: ±(0.3 x TD + 0.15)% of the set span
• ≥ 100 mbar measuring cells: ±(0.08 x TD + 0.07)% of the set span

26 Endress+Hauser
Deltabar S

Operating conditions (Installation)

General installation • The position-dependent zero shift can be corrected directly at the device via operating key, for devices with
instructions external operation even in hazardous areas. Diaphragm seals also shift the zero point, depending on the
installation position (→ See also page 64 ff, "Installation instructions, Diaphragm seal systems").
• The housing of the Deltabar S can be rotated up to 380°. → See also page 29, section "Turn the housing".
• Endress+Hauser offers a mounting bracket for installing the device on pipes or walls. → See also page 28,
section "Wall- and pipe-mounting".
• When measuring in media with solid proportions, such as dirty liquids, installing separators and drain valves
is useful for capturing and removing sediment.
• Using a three-valve or five-valve manifold allows for easy commissioning, installation and maintenance
without interrupting the process.
• General recommendations for the impulse piping can be found in DIN 19210 "Methods for measurement of
fluid flow; differential piping for flow measurement devices" or the corresponding national or international
standards.
• Install the impulse piping with a continuous gradient of at least 10%.
• When routing the impulse piping outdoors, ensure that sufficient anti-freeze protection is used, e.g. by using
pipe heat tracing.
• For FMD77 and FMD78: See page 64 ff, "Installation instructions, Diaphragm seal systems" section.

Measuring arrangement Flow measurement

• The PMD70 and PMD75 are best suited to flow measurement.
• Measuring arrangement for gases: Mount device above the measuring point.
• Measuring arrangement for liquids and vapours: Mount device below tapping point.
• For flow measurement in vapours, mount the condensate traps at the same level as the same the tapping
point and at the same distance from Deltabar S.

Level measurement
• PMD70, PMD75, FMD76 and FMD77 are best suited to level measurement in open tanks. All Deltabar S
devices are suitable for level measurement in closed tanks.

Measuring arrangement level measurement in open tanks

• PMD70, PMD75: Mount device below the lower measuring connection. The negative side is open to
atmosphere pressure.
• FMD76, FMD77: Mount device direct on the tank. The negative side is open to atmosphere pressure.

Measuring arrangement level measurement in closed tanks and closed tanks with superimposed vapour
• PMD70, PMD75: Mount device below the lower measuring connection. Always connect the negative side
above the maximum level.
• FMD76, FMD77: Mount device direct on the tank. Always connect the negative side above the maximum
level.
• In the case of level measurement in closed tanks with superimposed vapour, a condensate trap ensures
pressure which remains constant on the minus side.

Pressure measurement
• The PMD70 and PMD75 are best suited to differential pressure measurement.
• Measuring arrangement for gases: Mount device above the measuring point.
• Measuring arrangement for liquids and steams: Mount device below tapping point.
• For differential pressure measurement in vapour, mount the condensate traps at the same level as the same
the tapping point and at the same distance from Deltabar S.

Endress+Hauser 27
 Deltabar S

Heat insulation – FMD77 The FMD77 must only be insulated up to a certain height. The maximum permitted insulation height is labelled
on the devices and applies to an insulation material with a heat conductivity
≤ 0.04 W/(m x K) and to the maximum permitted ambient and process temperature (→ see table below). The
data were determined under the most critical application "quiescent air".

TA λ ≤ 0.04 W
m•K

TP
P01-FMD77xxxx-11-xx-xx-xx-000

Maximum permitted insulation height

FMD77

Ambient temperature (TA) ≤ 70°C (158°F)

Process temperature (TP) max. 400°C (752°F), depending on the
diaphragm seal filling oil used (→ see
page 58)

Wall- and pipe-mounting Endress+Hauser offers a mounting bracket for installing the device on pipes or walls. → See also page 67 ff,
feature 110, "Additional options 2".
Note!
If a valve block is used, its dimensions should also be taken into consideration.

➀
37.5
97.5
135

74
12
4

74
106

P01-xMD7xxxx-11-xx-xx-xx-008

Mounting bracket for wall and pipe-mounting

A bracket including mounting accessories for pipe mounting is included with the device.
1 Device mounting

28 Endress+Hauser
Deltabar S

"Separate housing" version With the "separate housing" version, you are able to mount the housing with the electronics insert at a distance
from the measuring point. This facilitates trouble-free measurement:
• Under particularly difficult measuring conditions (at installation locations that are cramped or difficult to
access)
• If rapid cleaning of the measuring point is required
• If the measuring point is exposed to vibrations.
IP 69K applies for the process connection with sensor if FEP cable are used.
You can choose between different cable versions:
• PE (2 m, 5 m and 10 m)
• FEP (5 m).
→ See also Page 68 ff, Feature 110, "Additional options 2", Version "G".
→ For the dimensions, see Page 54.

r ³ 120 mm
➀
➁

P01-xMD7xxxx-11-xx-xx-xx-010

In the case of the "separate housing" version, the sensor is delivered with the process connection and cable ready
mounted. The housing and a mounting bracket are enclosed as separate units. The cable is provided with a socket at both
ends. These sockets are simply connected to the housing and the sensor.
1 Process connection with sensor
2 Cable, both ends are fitted with a socket
3 Mounting bracket provided, suitable for pipe and wall mounting
4 Housing with electronic insert

Technical data of the PE and FEP cable:

• Minimum bending radius: 120 mm (4.72 inch)
• Cable extraction force: max. 450 N
• Resistance to UV light

Turn the housing The housing can be rotated up to 380° by loosening the Allen screw.
Your benefits
• Simple mounting by optimally aligning the housing
• Good, accessible device operation
• Optimum readability of the on-site display (optional).

Endress+Hauser 29
 Deltabar S

max. 380°

P01-xMD7xxxx-17-xx-xx-xx-001

Align the housing by loosening the Allen screw.

T14 and T15 housing: 2 mm Allen key; T17 housing: 3 mm Allen key

Oxygen applications Oxygen and other gases can react explosively to oils, grease and plastics, such that, among other things, the
following precautions must be taken:
– All components of the system, such as measuring devices, must be cleaned in accordance with the BAM
(DIN 19247) requirements.
– Dependent on the materials used, a certain maximum temperature and a maximum pressure for oxygen
applications must not be exceeded.
The devices suitable for gaseous oxygen applications are listed in the following table with the specification pmax.

Order code for devices cleaned for pmax for oxygen applications Tmax for oxygen
oxygen applications applications

PMD70 – * * * ** * * * 2 * *, 30 bar 60°C (140°F)

Devices with 500 mbar or 3000 mbar
measuring cell

PMD70 – * * * ** * * * 2 * *, PN of the flange 60°C (140°F)

Devices with 25 mbar or 100 mbar
measuring cell

PMD75 – * * * ** * * * K * * 160 bar 85°C (185°F)

PMD75 – * * * ** * * * 2 * * 160 bar 60°C (140°F)

PMD75 – * * * ** * * * 3 * * 160 bar 60°C (140°F)

FMD76 – * * * ** * T * * *, 30 bar 60°C (140°F)

Devices with 500 mbar or 3000 mbar
measuring cell

FMD76 – * * * ** * T * * *, PN of the measuring cell 60°C (140°F)

Devices with 25 mbar or 100 mbar
measuring cell

FMD77 – * * * ** T * F * * PN of the flange 60°C (140°F)

FMD78 – * * * ** * ** 4 * * 90 bar 85°C (185°F)

FMD78 – * * * ** * ** D * *

Ultra pure gas applications Endress+Hauser also offers devices for special applications, such as ultra pure gas, cleaned from oil and grease.
No special restrictions regarding the process conditions apply to these devices.
→ See also page 67 ff, PMD70 and PMD75: feature 80 "Seal", FMD76 and FMD77: feature 70 "Process
connection low-pressure side, material, seal".

Diaphragms for materials with With regard to materials in which hydrogen build-up takes place, hydrogen atoms can diffuse through the metal
hydrogen build-up (Gold- diaphragms. This can result in incorrect measurement results.
Rhodium coating) Endress+Hauser offers diaphragms with Gold-Rhodium coating for this application.
→ See also page 70 "Ordering information PMD75", page 76 "Ordering information FMD77" or page 79
"Ordering information FMD78", feature 60 "Membrane material".

30 Endress+Hauser
Deltabar S

Operating conditions (Environment)

Ambient temperature range • PMD75, FMD77, FMD78: –40...+85°C (–40...+185°F), devices for lower temperatures on request
• PMD70, FMD76: –20...+85°C (–4...+185°F)
• On-site display: –20...+70°C (–4...+158°F)
Extended temperature application range with restrictions in optical properties such as display speed and
contrast: –40...+85°C (–40...+185°F)
• Separate housing: –40 to +60°C (–40 to +140°F)
For devices for use in hazardous areas, see Safety instructions, Installation or Control Drawing (→ See also page
81, sections "Safety Instruction" and "Installation/Control drawings").
The device can be used in this temperature range. The values of the specification, such as thermal change, may
be exceeded. → See also DIN 16086.

Storage temperature range • –40...+100°C (–40...+212°F)

• On-site display: –40...+85°C (–40...+185°F)
• Separate housing: –40 to +60°C (–40 to +140°F)

Degree of protection • → See page 67 ff, feature 30 "Housing, Cable entry, Protection".
• Degree of protection IP 68 for T17 housing: 1.83 mH2O for 24 h
• Degree of protection IP 69K for process connection with sensor with separate housing and FEP cable.

Climate class Class 4K4H (air temperature: –20...55°C/–4...+131F, relative humidity: 4...100%) fulfilled as per
DIN EN 60721-3-4 (condensation possible)

Vibration resistance Device/Additional option Housing Test standard Vibration resistance

PMD70/ optional on-site display on GL guaranteed for:
FMD76 the side (T14) 2...18 Hz: ±4 mm;
18...500 Hz: 5 g in all 3 planes

PMD75 optional on-site display on IEC 61298-3 guaranteed for:

the side (T14) 10...60 Hz: ±0.35 mm;
60...2000 Hz: 5 g in all 3 planes
PMD75 optional on-site display on
the top (T15)

with mounting bracket IEC 61298-3 guaranteed for:

10...60 Hz: ±0.15 mm;
60...500 Hz: 2 g in all 3 planes

Electromagnetic compatibility • Electromagnetic compatibility to EN 61326 and NAMUR recommendation EMC (NE21). For details refer
to the declaration of conformity.
• With enhanced immunity against electromagnetic fields as per EN 61000-4-3:
30 V/m with closed cover (for devices with T14 or T15 housing)
• Maximum deviation: < 0.5% of span 1
• All EMC measurements were performed with a turn down (TD) = 2:1.

1) Larger deviations possible with PMD70 with 25 mbar or 100 mbar sensor

Overvoltage protection • Overvoltage protection:

(optional) – Nominal functioning DC voltage: 600 V
– Nominal discharge current: 10 kA
• Surge current check î = 20 kA as per DIN EN 60079-14: 8/20 μs satisfied
• Arrester AC current check I = 10 A satisfied
→ See also page 68 ff, feature 100 "Additional options 1" and feature 110 "Additional options 2", version "M
Overvoltage protection".
Note!
Devices with integrated overvoltage protection must be earthed.

Endress+Hauser 31
 Deltabar S

Operating conditions (Process)

Process temperature limits • PMD70: –20...+85°C (–4...+185°F)

• FMD76: –20...+85 °C (–4...+185°F)
• PMD75 with impulse piping longer than 100 mm: –40...+120°C (–40...+248°F),
with side flanges C22.8 and impulse piping longer than 100 mm: –10...+120°C (14...+248°F)
• FMD77 and FMD78, depending on the diaphragm seal and filling oil: up to + 400°C (+752°F)
Note!
• For oxygen applications, observe page 30 "Oxygen applications" section.
• PMD70, FMD76, PMD75 and FMD78: Observe the Process temperature range of the seal.
→ See also the following section "Process temperature range, seals".
• FMD77 and FMD78: Observe the temperature application limits of the diaphragm seal oil.
→ See also page 58, sections "Diaphragm seal filling oils".
• FMD77 and FMD78: Do not use diaphragm seals with 0.09 mm PTFE foil on AISI 316L (1.4435/1.4405)
for vacuum applications, upper temperature limit +204°C (+400°F).

Process temperature range, PMD70 (with ceramic measuring diaphragms)

seals
Versions for feature 80 in the order code Seal Process temperature range

A FKM Viton –20...+85°C (–4...+185°F)

B EPDM –20...+85°C (–4...+185°F)

D Kalrez, Compound 4079 +5...+85°C (+41...+185°F)

E Chemraz, Compound 505 –20...+85°C (–4...+185°F)

1 FKM Viton, cleaned from oil and greace –10...+85°C (+14...+185°F)

2 FKM Viton, cleaned for oxygen service –10...+60°C (+14...+140°F)

FMD76 (with ceramic measuring diaphragms)

Versions for feature 70 in the order code Seal Temperature operating range

B, D, F, G, U FKM Viton –20...+85°C (–4...+185°F)

K, L EPDM –20...+85°C (–4...+185°F)

FDA 21 CFR 177.2600

M, N Kalrez, Compound 4079 +5...+85°C (+41...+185°F)

P, Q Chemraz, Compound 505 –20...+85°C (–4...+185°F)

S FKM Viton, cleaned from oil and greace –10...+85°C (+14...+185°F)

T FKM Viton, cleaned for oxygen service –10...+60°C (+14...+140°F)

PMD75 (with metallic measuring diaphragms)

Versions for feature 80 in the Seal Process temperature range 1

order code

A FKM Viton –20...+85°C (–4...+185°F)

C PTFE –40...+85°C (–40...+185°F)

F NBR –20...+85°C (–4...+185°F)

H Copper –40...+85°C (–40...+185°F)

K Copper, cleaned for oxygen service –20...+85°C (–4...+185°F)

1 FKM Viton, cleaned from oil and greace –10...+85°C (+14...+185°F)

2 FKM Viton, cleaned for oxygen service –10...+60°C (+14...+140°F)

3 PTFE, cleaned for oxygen service –20...+60°C (–4...+140°F)

1) lower temperature on request

32 Endress+Hauser
Deltabar S

FMD77 (with metallic measuring diaphragms)

Versions for feature 70 in the Seal on the LP side (–) Process temperature range 1
order code

B, D, F, G FKM Viton –20...+85°C (–4...+185°F)

H, J PTFE –40...+85°C (–40...+185°F)

K, L EPDM –40...+85°C (–40...+185°F)

M, N Kalrez, Compound 6375 +5...+85°C (+41...+185°F)

P, Q Chemraz, Compound 505 –20...+85°C (–4...+185°F)

S FKM Viton, cleaned from oil and greace –10...+85°C (+14...+185°F)

T FKM Viton, cleaned for oxygen service –10...+60°C (+14...+140°F)

1) lower temperature on request

Pressure specifications • The maximum pressure for the measuring device is dependent on the lowest-rated element with regard to
pressure, see the following sections for this:
– → page 14 ff, section "Measuring range"
– → chapter "Mechanical construction".
The MWP (maximum working pressure) is specified on the nameplate. This value refers to a reference
temperature of 20°C (68°F) or 100°F for ANSI flanges and may be applied to the device for an unlimited
time. Observe pressure-temperature dependency.
• The pressure values permitted at higher temperatures can be found in the following standards:
– EN 1092-1: 2001 Tab. 18 1
– ASME B 16.5a – 1998 Tab. 2-2.2 F316
– ASME B 16.5a – 1998 Tab. 2.3.8 N10276
– JIS B 2220
• For PMD70 and PMD75, the MWP applies for the temperature ranges specified in the "Ambient temperature
range" (→ page 31) and "Process temperature limits" (→ page 32) sections.
• The test pressure corresponds to the over pressure limit of the measuring instrument (Over pressure limits
OPL = 1.5 x MWP) and may fit only temporally limited, so that no permanent damage develops.
• The Pressure Equipment Directive (EC Directive 97/23/EC) uses the abbreviation "PS". The abbreviation
"PS" corresponds to the MWP (maximum working pressure) of the measuring device.
• In the case of sensor range and process connections where the OPL (Over Pressure Limit) of the pressure
connection is smaller than the nominal value of the sensor, the device is set at the factory, at the very
maximum, to the OPL value of the process connection. If you want to use the entire sensor range, select a
process connection with a higher OPL value (1.5 x PN; PN = MWP).
• In oxygen applications, the values for "pmax and Tmax for oxygen applications" as per page 30, "Oxygen
applications" may not be exceeded.

1) With regard to its stability property, the material 1.4435 is identical to 1.4404 which is grouped under 13EO
in EN 1092-1 Tab. 18. The chemical composition of the two materials can be identical.

Endress+Hauser 33
 Deltabar S

Mechanical construction
Housing dimensions T14,
optional display on the side 152
111 111

FIELD TERMINALS
H
P01-xMD7xxxx-06-00-xx-xx-000

Front view, left-hand side view, top view

→ See the process connection in question for installation height. Housing weight see page 55.

Housing dimensions T15,

155
optional display on the top
115 127
H
H

P01-xMD7xxxx-06-00-xx-xx-001

Front view, left-hand side view, top view

→ See the process connection in question for installation height. Housing weight see page 55.

Housing dimensions T17,

132
optional display on the top
102 115
H

P01-xMD7xxxx-06-00-xx-xx-002

Front view, left-hand side view, top view

→ See the process connection in question for installation height. Housing weight see page 55.

34 Endress+Hauser
Deltabar S

Process connections PMD70 Note!

with ceramic measuring Some device versions have CRN approval. For a CRN-approved device, a CRN-approved process connection
diaphragms (→ see page 68, feature 70 "Process connection") has to be ordered with a CSA approval (→ see page 67,
feature 10 "Approval"). These devices are fitted with a separate plate bearing the registration number
0F10524.5C.

+ – – +

7/16-20 UNF +
M10
41.3
108
H

1/4-18 NPT
RC1/4

54 96
84

P01-PMD70xxx-06-09-xx-xx-000

Process connection PMD70, oval flange

H Device height → see page 36, section "Device height H"

Ver- Connection Mounting Material Accessories Weight 1

sion

B 1/4-18 NPT IEC 61518 7/16-20 UNF Steel C 22.8 2 vent valves (AISI 316L/1.4404) 4.0 kg
2
included
D 1/4-18 NPT IEC 61518 7/16-20 UNF AISI 316L 4.0 kg

F 1/4-18 NPT IEC 61518 7/16-20 UNF Alloy C276 3 Vent valves (Alloy C276/2.4819), 4.2 kg
see page 68 feature 110
"Additional options 2".

U RC 1/4 7/16-20 UNF AISI 316L 2 2 vent valves (AISI 316L/1.4404) 4.0 kg
included
1 1/4-18 NPT IEC 61518 PN 160: M10 Steel C 22.8 4.0 kg
2
2 1/4-18 NPT IEC 61518 PN 160: M10 AISI 316L 4.0 kg

3 1/4-18 NPT IEC 61518 PN 160: M10 Alloy C276 3 Vent valves (Alloy C276/2.4819), 4.2 kg
see page 68, feature 110
"Additional options 2".

1) Process connection weight, for housing weight see page 55

2) AISI 316L/1.4435
3) Alloy C276/2.4819

Endress+Hauser 35
 Deltabar S

Process connections PMD70

with ceramic measuring
diaphragms (continued) + –

7/16-20 UNF + PVDF

H
108
41.3
1/4-18 NPT

54 96
84

P01-PMD70xxx-06-09-xx-xx-001

Process connection PMD70, version G, PVDF inlay, PN = 10 bar, process temperature T = –10...+60°C (14...+140°F)

H Device height → see page 36, section "Device height H"

Version Connection Mounting Material Weight 1

G 1/4-18 NPT IEC 61518 7/16-20 UNF PVDF 3.8 kg

1) Process connection weight, for housing weight see page 55

Device height H

Description Device height H

T14 housing, optional display on the side 253 mm

T15 housing, optional display on the top, flat cover 259 mm

T15 housing, optional display on the top, high cover 270 mm

T17 housing, optional display on the side 269 mm

36 Endress+Hauser
Deltabar S

Process connections PMD75 Note!

with metallic measuring Some device versions have CRN approval. For a CRN-approved device, a CRN-approved process connection
diaphragms (→ see page 70, feature 70 "Process connection") has to be ordered with a CSA approval (→ see page 68,
feature 10 "Approval"). These devices are fitted with a separate plate bearing the registration number
0F10524.5C.

Oval flange, connection 1/4-18 NPT or RC 1/4

7/16-20 UNF
M 10
H

41.3
+ – – +
85

1/4-18 NPT
RC1/4

54 106
85
100

7/16-20 UNF
M10 (M12)
H

41.3
72

+– 1/4-18 NPT –+
RC1/4

54 100
87
98
P01-PMD75xxx-06-09-xx-xx-005

Process connection PMD75,

above 10 mbar and 30 mbar measuring cell; below: Measuring cell ≥ 100 mbar
H Device height → see page 39, section "Device height H"

Ver- Connection Mounting Material Accessories Weight 1

sion

B 1/4-18 NPT IEC 61518 7/16-20 UNF Steel C 22.8 2 vent valves (AISI 316L/1.4404) 4.2 kg
2
included
D 1/4-18 NPT IEC 61518 7/16-20 UNF AISI 316L 4.2 kg
3
F 1/4-18 NPT IEC 61518 7/16-20 UNF Alloy C276 Vent valves (Alloy C276/2.4819), 4.5 kg
see page 71, feature 110
"Additional options 2".

U RC 1/4 7/16-20 UNF AISI 316L 2 2 vent valves (AISI 316L/1.4404) 4.2kg
included
1 1/4-18 NPT IEC 61518 – PN 160: M10 Steel C 22.8 4.2 kg
– PN 420: M12

2 1/4-18 NPT IEC 61518 – PN 160: M10 AISI 316L 2 4.2 kg

– PN 420: M12

3 1/4-18 NPT IEC 61518 – PN 160: M10 Alloy C276 3 Vent valves (Alloy C276/2.4819), 4.5 kg
– PN 420: M12 see page 71, feature 110
"Additional options 2".

1) Weight of process connections without vent valves with 10 mbar or 30 mbar sensors, process connections without
vent valves with sensors ≥ 100 mbar weght approx. 800 g less. Housing weight see page 55.
2) AISI 316L/1.4435 or 1.4404
3) Alloy C276/2.4819

Endress+Hauser 37
 Deltabar S

Process connections PMD75 Oval flange, connection 1/4-18 NPT or RC 1/4, with side vent
with metallic measuring
diaphragms (continued)

7/16-20 UNF 1/4-18 NPT

41.3
+ – – +
85

42
1/4-18 NPT
RC1/4

54 106
85
100
P01-PMD75xxx-06-09-xx-xx-004

Process connection PMD75, 10 mbar and 30 mbar measuring cell

7/16-20 UNF
1/4-18 NPT
H

41.3

28
72

+– 1/4-18 NPT –+
RC1/4

54 100
87
98
P01-PMD75xxx-06-09-xx-xx-003

Process connection PMD75, nominal value ≥ 100 mbar

H Device height → see page 39, section "Device height H"

Ver- Connection Mounting Material Accessories Weight 1

sion

C 1/4-18 NPT IEC 61518 7/16-20 UNF Steel C 22.8 4 locking screws and 4.2 kg
2 vent valves included
E 1/4-18 NPT IEC 61518 7/16-20 UNF AISI 316L 2 4.2 kg
(AISI 316L/1.4404)

H 1/4-18 NPT IEC 61518 7/16-20 UNF Alloy C276 3 Vent valves (Alloy C276/2.4819), 4.5 kg
see page 71, feature 110
"Additional options 2".

V RC 1/4 7/16-20 UNF AISI 316L 2 4 looking screws and 4.2 kg

2 vent valves included
(AISI 316L/1.4404)

1) Weight of process connections without vent valves with 10 mbar or 30 mbar sensors, process connections without
vent valves with sensors ≥ 100 mbar weght approx. 800 g less. Housing weight see page 55
2) PN 160 bar measuring cells: AISI 316L/1.4435, PN 420 bar measuring cells: AISI 316L/1.4435 or 1.4404
3) Alloy C276/2.4819

38 Endress+Hauser
Deltabar S

Process connections PMD75 Oval flange, prepared for diaphragm seal mount
with metallic measuring
diaphragms (continued)
7/16-20 UNF

H
➁
➀
➂

41.3
72
+– M6 –+

54 54
87
98

P01-PMD75xxx-06-09-xx-xx-002

Left: Process connection PMD75, version W, prepared for diaphragm seal mount
Right: Position of the copper ring seal
H Device height → see the following section "Device height H"
1 Diaphragm seal attachment
2 Copper ring seal
3 Cup diaphragm

Device height H

Description Device height H 1

T14 housing, optional display on the side 217 mm (230 mm)

T15 housing, optional display on the top, flat cover 223 mm (236 mm)
T15 housing, optional display on the top, high cover 234 mm (247 mm)

T17 housing, optional display on the side 233 mm (246 mm)

1) Values for devices with 10 mbar and 30 mbar measuring cell in brackets

Endress+Hauser 39
 Deltabar S

Process connection FMD76 Note!

with ceramic measuring • Some device versions have CRN approval. For a CRN-approved device, a CRN-approved process connection
diaphragms (→ see page 73, feature 70 "Process connection") has to be ordered with a CSA approval (→ see page 72,
feature 10 "Approval"). These devices are fitted with a separate plate bearing the registration number
0F10524.5C.
• FMD76 devices with an EN/DIN flange DN 80 PN 40, an ANSI flange 3" 150 lbs or a JIS flange 80 A 10 K
can only be mounted with an open-ended wrench.

EN/DIN flanges, connection dimensions as per EN 1092-1/DIN 2527

41

41.3

7/16-20 UNF

H
h
g2
1/4-18 NPT
2

ø46

b
g
k
D
P01-FMD76xxx-06-09-xx-xx-000

Process connection FMD76, high-pressure side: EN/DIN flange,

low-pressure side: connection 1/4-18 NPT
Application limits for version "G" in feature 70 "Process connection low-pressure side" with PVDF inlay:
PN = 10 bar, process temperature T = –10...+60°C (14...+140°F)
H Device height → see page 42, section "Device height H, devices with flange"
h Height of the device without flange thickness b

Flange Boltholes
1
Version Material Nominal Shape Nominal Diameter Thickness Raised Quantity Diameter Hole Flange
diameter pressure face circle weight 2

D b g g2 k

[mm] [mm] [mm] [mm] [mm] [kg]

B AISI 316L DN 80 B1 (D) PN 10-40 200 24 138 8 18 160 5,3

3
D ECTFE DN 80 – PN 10-40 200 24 – 8 18 160 5,3
4
E Alloy C276 DN 80 B1 (D) PN 10-40 200 24 138 8 18 160 6

F AISI 316L DN 100 B1 (C) PN 10-16 220 22 – 8 18 180 6

G AISI 316L DN 100 B1 (D) PN 25-40 235 26 162 8 22 190 8

3
H ECTFE DN 100 – PN 25-40 235 26 – 8 22 190 8

J Alloy C276 4 DN 100 B1 (D) PN 25-40 235 26 162 8 22 190 9

3
L ECTFE DN 100 – PN 10-16 220 22 – 8 18 180 6
4
M Alloy C276 DN 100 B1 (C) PN 10-16 220 22 – 8 18 180 6,8

1) Designation as per DIN 2527 in brackets

2) Housing weight see page 55
3) ECTFE coating on AISI 316L/1.4435,
When operating in hazardous area, avoid electrostatic charge of the plastic surfaces.
4) Alloy C276/2.4819

40 Endress+Hauser
Deltabar S

Process connection FMD76 ANSI flanges, connection dimensions as per ANSI B 16.5, raised face RF and
with ceramic measuring JIS flanges, connection dimensions as per JIS B 2220, raised face RF
diaphragms (continued)
41
1.61 in
41.3
1.63 in

7/16-20 UNF

H
h
g2
1/4-18 NPT

ø46

b
ø1.81 in

1.6 (0.06 in)

2 (0.078 in)
g
k
ANSI

JIS
D
P01-FMD76xxx-06-09-xx-xx-001

Process connection FMD76, high-pressure side: ANSI or JIS flange (see table below),
low-pressure side: connection 1/4-18 NPT
H Device height → see page 42, section "Device height H, devices with flange"
h Height of the device without flange thickness b

Flange Boltholes
Version Material Nominal Class/ Diameter Thickness Raised face Quantity Diameter Hole circle Flange
diameter Nominal weight 1
pressure

D b g g2 k

[in] [in] [in] [in] [in] [kg]

[mm] [mm] [mm] [mm] [mm]
ANSI flanges

P AISI 316/ 3 in 150 7.5 0.94 5 4 0.75 6 4.9

316L 2 lb./sq.in 190.5 23.9 127 19.1 152.4

R ECTFE 3 4.9

S Alloy C276 5.5

T AISI 316/ 4 in 150 9 0.94 6.19 8 0.75 7.5 7.1

316L 2 lb./sq.in 228.5 23.9 157.2 19.1 190.5

U ECTFE 3 7.1

V Alloy C276 8

W AISI 316/ 4 in 300 10 1.25 6.19 8 0.88 7.88 11.7

316L 2 lb./sq.in 254 31.8 157.2 22.4 200.2

JIS flanges

1 AISI 316L/ 80 A 10 K 7.32 0.71 5 8 0.75 5.9 3.3

1.4435 185 18 127 19.1 150
3 Alloy C276 3.7

4 AISI 316L/ 100 A 10 K 8.27 0,71 5.95 8 0.75 6.89 4.4

1.4435 210 18 151 19.1 175

1) Housing weight see page 55

2) Combination of AISI 316 for required pressure resistance and AISI 316L for required chemical resistance (dual rated)
3) ECTFE coating on AISI 316L/1.4435.
When operating in hazardous area, avoid electrostatic charge of the plastic surfaces.

Endress+Hauser 41
 Deltabar S

Process connection FMD76 Device height H, devices with flange

with ceramic measuring
diaphragms (continued) Description Device height H (h + b)

T14 housing, optional display on the side 175 mm + flange thickness b (see tables)

T15 housing, optional display on the top, flat cover 181 mm + flange thickness b (see tables)

T15 housing, optional display on the top, high cover 192 mm + flange thickness b (see tables)

T17 housing, optional display on the side 191 mm + flange thickness b (see tables)

Process connections FMD77

100
with metallic measuring
diaphragms, low-pressure
side 7/16-20 UNF

41.3
+– –+

1/4-18 NPT
150

103.7
P01-FMD77xxx-06-xx-xx-xx-001

Low-pressure side: connection 1/4-18 NPT, mounting optionally 7/16-20 UNF,

Side flanges material of the basic device: AISI 316L/1.4435 or 1.4404
high-pressure side, see the following section "Process connections, high-pressure side FMD77"

42 Endress+Hauser
Deltabar S

Process connections FMD77 Note!

with metallic measuring • Some device versions have CRN approval. For a CRN-approved device, a CRN-approved process connection
diaphragms, high-pressure (→ see page 76, feature 70 "Process connection") has to be ordered with a CSA approval (→ see page 75,
side feature 10 "Approval"). These devices are fitted with a separate plate bearing the registration number
0F10524.5C.
• Specifications for the "TK Ambient" and "TK Process" are listed in the following tables. These are typical
values. These temperature coefficients apply to silicone oil and the membrane material AISI 316L/1.4435.
For other filling oils, this temperature coefficient must be multiplied by the TK correction factor of the
corresponding filling oil. For the TK correction factors, see also page 58, section "Diaphragm seal filling oils".

EN/DIN flanges, connections as per EN 1092-1/DIN 2527

H
h
g2

b
dM
1.6 mm
0.06 in

L
g

k d3
D g

P01-FMD77xxx-06-09-xx-xx-002

Process connection FMD77, high-pressure side EN/DIN flange with and without extended diaphragm seal, material
AISI 316L
H Device height see page 45, → section "Device height H"
h Height of the device without flange thickness b

Flange Boltholes Diaphragm seal

Ver- No- Nominal Shape Dia- Thick- Raised Exten- Exten- Quan- Dia- Hole max. TK TK Flange
1
sion minal pressure meter ness face sion sion tity meter circle Dia- Am- Pro- weight 2
dia- length dia- phragm bient cess
meter meter dia-
meter

D b g L d3 g2 k dM

[mm] [mm] [mm] [mm] [mm] [mm] [mm] [mbar/10 K] [kg]

A DN 50 PN 10-40 B1 (D) 165 20 102 – – 4 18 125 59 +3.02 +1.25 3.0

B DN 80 PN 10-40 B1 (D) 200 24 138 – – 8 18 160 89 +0.23 +0.18 5.2

C DN 80 PN 10-40 B1 (D) 200 24 – 50 76 8 18 160 72 +0.23 +0.11 6.2

100 6.7
200 7.8

F DN 100 PN 10-16 B1 (C) 220 20 – – – 8 18 180 89 +0.23 +0.28 4.8

G DN 100 PN 25-40 B1 (D) 235 24 162 – – 8 22 190 89 +0.23 +0.11 6.7

1) Designation as per DIN 2527 in brackets

2) Housing weight see page 55

Endress+Hauser 43
 Deltabar S

Process connections FMD77 ANSI flanges, connection dimensions as per B 16.5, raised face RF
with metallic measuring
diaphragms, high-pressure
side (continued)

H
h
g2

b
1.6 mm dM
0.06 in

L
g

k d3
D g

P01-FMD77xxx-06-09-xx-xx-000

Process connection FMD77, high-pressure side ANSI flange with and without extended diaphragm seal, material
AISI 316/316L
H Device height → see page 45, section "Device height H"
h Height of the device without flange thickness b

Flange Boltholes Diaphragm seal

Ver- No- Class Dia- Thick- Raised Exten- Exten- Quan- Dia- Hole max. TK TK Flange
sion minal meter ness face sion sion tity meter circle Dia- Am- Pro- weight 1
dia- length dia- phragm bient cess
meter meter dia-
meter

D b g L d3 g2 k dM

[lb./sq.in] [in] [in] [in] [in] [in] [in] [in] [in] [mbar/10 K] [kg]
[mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm]

N 2 150 6 0.75 3.62 – – 4 0.75 4.75 2.32 +3.02 +0.90 2.6

152.4 19.1 91.9 19.1 120.7 59
P 3 150 7.5 0.94 5 – – 4 0.75 6 3.50 +0.23 +0.18 5.1
190.5 23.9 127 19.1 152.4 89

Q 3 150 7.5 0.94 5 2 3 4 0.75 6 2.83 +0.23 +0.11 6

190.5 23.9 127 50.8 76.2 19.1 152.4 72

4 6.6
101.6

6 7.1
152.4

8 7.7
203.8

T 4 150 9 0.94 6.19 – – 8 0.75 7.5 3.50 +0.23 +0.11 7.2

228.6 23.9 157.2 19.1 190.5 89

W 4 300 10 1.25 6.19 – – 8 0.88 7.88 3.50 +0.23 +0.11 11.7

254 31.8 157.2 22.4 200.2 89

1) Housing weight see page 55

44 Endress+Hauser
Deltabar S

Process connections FMD77 JIS flanges, connection dimensions as per JIS B 2220, raised face RF
with metallic measuring
diaphragms, high-pressure
side (continued)

H
h
0.0787"
g2

2 mm

b
dM
g

k
D
P01-FMD77xxx-06-09-xx-xx-001

Process connection FMD77, high-pressure side, JIS flange, material AISI 316L/1.4435
H Device height → see the following section "Device height H"
h Height of the device without flange thickness b

Flange Boltholes Diaphragm seal

Ver- Nominal Nominal Diameter Thick- Raised Quan- Diameter Hole max. Dia- TK TK Flange
sion diameter pressure ness face tity circle phragm Ambient Process weight 1
diameter

D b g g2 k dM

[mm] [mm] [mm] [mm] [mm] [mm] [mbar/10 K] [kg]

[in] [in] [in] [in] [in] [in]

X 50 A 10 K 155 16 96 4 19 120 59 +3.02 +0.60 2.3

6.1 0.63 3.78 0.75 4.72 2.32
1 80 A 10 K 185 18 126 8 19 150 89 +0.23 +0.31 3.5
7.28 0.71 4.96 0.75 5.91 3.50

4 100 A 10 K 210 18 151 8 19 175 89 +0.23 +0.11 4.7

8.27 0.71 5.94 0.75 6.89 3.50

1) Housing weight see page 55

Device height H

Description Device height H (h + b)

T14 housing, optional display on the side 325 mm + flange thickness b (see tables)

T15 housing, optional display on the top, flat cover 331 mm + flange thickness b (see tables)

T15 housing, optional display on the top, high cover 342 mm + flange thickness b (see tables)

T17 housing, optional display on the side 341 mm + flange thickness b (see tables)

Endress+Hauser 45
 Deltabar S

FMD78 Basic unit

P01-FMD78xxx-06-xx-xx-xx-000

FMD78 Basic unit

H Device height → the following section "Device height H"
1 Diaphragm seal attachment

Device height H

Description Device height

T14 housing, optional display on the side 217 mm

T15 housing, optional display on the top, flat cover 223 mm

T15 housing, optional display on the top, high cover 234 mm

T17 housing, optional display on the side 233 mm

46 Endress+Hauser
Deltabar S

Process connection FMD78 Note!

with metallic measuring • Specifications for the "TK Process" are listed in the following tables. These are typically values. These
diaphragms temperature coefficients apply to silicone oil and the membrane material AISI 316L/1.4435. For other filling
oils, this temperature coefficient must be multiplied by the TK correction factor of the corresponding filling
oil. For the TK correction factors, see also page 58, section "Diaphragm seal filling oils".
• The temperature coefficient "TK Ambient" is listed in relation to the capillary length on page 59 in the
"Influence of the temperature on the zero point" section.
• The weights of the diaphragm seals are given in the tables. See page 37 for the weight of the transmitter and
page 55 for the weight of the housing.
• The following drawings are drawings that illustrate how the system works in principle. In other words, the
dimensions of a diaphragm seal supplied can deviate from the dimensions given in this document.

Diaphragm seal cell structure

b
dM

P01-FMD78xxx-06-09-xx-xx-000

Process connection FMD78, material AISI 316L

Flange Diaphragm seal

Version Nominal Nominal Diameter Thickness max. Diaphragm TK Weight of two
diameter pressure 1 diameter Process diaphragm seals

D b dM

[mm] [mm] [mm] [mbar/10K] [kg]

UF DN 50 PN 16-400 102 20 59 +2.00 2.6

UH DN 80 PN 16-400 136 20 89 +0.20 4.6

UJ DN 100 PN 16-400 158 20 89 +0.30 6.2

Flange Diaphragm seal

Version Nominal Nominal Diameter Thickness max. Diaphragm TK Weight of two

diameter pressure 1 diameter Process diaphragm seals

D b dM

[in] [lb/sq.in] [in] [in] [in] [mbar/10K] [kg]

[mm] [mm] [mm]

VF 2 150-2500 3.99 0.79 2.32 +1.25 2.6

99 20 59

VH 3 150-2500 5.00 0.79 3.50 +0.25 4.6

127 20 89

VJ 4 150-2500 6.22 0.79 3.50 +0.19 6.2

158 20 89

1) The specified nominal pressure applies to the diaphragm seal. The maximum pressure for the measuring device is dependent on the lowest-rated element,
with regard to pressure, of the selected components. → See also page 33, section "Pressure specifications".

Endress+Hauser 47
 Deltabar S

Process connection FMD78 Threaded ISO 228 G 1/2 B and ANSI 1/2 MNPT, separator with PTFE seal
with metallic measuring
diaphragms (continued)
100 100

90

89
➀ ➀
SW22 SW22
22 AF 22 AF

6 1/2 NPT
G½

P01-FMD78xxx-06-09-xx-xx-012

Process connection FMD78, left: with threaded connection ISO 228 G 1/2 B, right: with threaded connection
ANSI 1/2 MNPT
1 PTFE seal as standard max. 260 °C/500 °F (higher temperatures on request)

Version Material Nominal pressure TK Process Weight of two

diaphragm seals

[mbar/10 K] [kg]

GA AISI 316L PN 40 +0.75 2.9

RL AISI 316L PN 40 +0.55 2.9

Tri-Clamp ISO 2852

h

dM
C7

P01-FMD78xxx-06-09-xx-xx-005

Process connection FMD78, Material: AISI 316L/1.4435, surface roughness of the wetted surfaces ≤ 0.8 μm as standard.
Lower surface roughness on request.

Version Nominal Nominal Nominal Diameter max. Height TK Process Weight of two
diameter diameter diameter Diaphragm diaphragm
ISO 2852 DIN 32676 diameter seals

C7 dM h

[in] [mm] [mm] [mm] [mbar/10 K] [kg]

TB DN 25 DN 25 1 50.5 24 37 +10.45 0.64

TC DN 38 DN 40 1 1/2 50.5 36 30 +2.40 2.0

TD DN 51 DN 50 2 64 48 30 +1.00 2.2

TF DN 76.1 – 3 91 73 30 +0.20 2.4

48 Endress+Hauser
Deltabar S

Process connection FMD78 Tri-Clamp pipe diaphragm seal ISO 2852

with metallic measuring
diaphragms (continued)

d1
D

d2
L

P01-FMD78xxx-06-09-xx-xx-001

Process connection FMD78, Material: AISI 316L, surface roughness of the wetted surfaces ≤ 0.8 μm as standard. Lower
surface roughness on request.

Version Nominal Nominal Diameter Diameter Diameter Height Face-to-face TK Process Weight of two
diameter diameter length diaphragm
ISO 2852 seals

D d1 d2 h L
[in] [mm] [mm] [mm] [mm] [mm] [mbar/10 K] [kg]

SB DN 25 1 22.5 43.5 50.5 67 126 +4.49 3.4

1
SC DN 38 1 1/2 35.5 43.5 50.5 67 126 +3.46 2
SD 1 DN 51 2 48.6 56.5 64 79 100 +2.69 3.4

1) Including 3.1 and pressure test as per Pressure Equipment Directive, category II

Varivent N for pipes DN 40 – DN 162

40

dM max. = 50
ø68
P01-FMD78xxx-06-09-xx-xx-006

Process connection FMD78, surface roughness of the wetted surfaces ≤ 0.8 μm as standard. Lower surface roughness on
request.

Version Material Nominal pressure TK Process Weight of two

diaphragm seals

[mbar/10 K] [kg]

TR AISI 316L/1.4435 PN 40 +1.65 2.6

Endress+Hauser 49
 Deltabar S

Process connection FMD78 DRD DN50 (65 mm)

with metallic measuring
diaphragms (continued)

41

23.6
dM max. =50 4 x ø11.5
ø65–1.2
ø84
ø105
P01-FM78xxx-06-09-xx-xx-002

Process connection FMD78, surface roughness of the wetted surfaces ≤ 0.8 μm as standard. Lower surface roughness on
request.

Version Material Nominal pressure TK Process Weight of two

diaphragm seals

[mbar/10 K] [kg]

TK AISI 316L/1.4435 PN 25 +1.25 1.5

Hygienic connection, sanitary tank spud, extended diaphragm seal 2"

53.5

ø91.45

ø100

ø132.7

P01-FMD78xxx-06-09-xx-xx-011

Process connection FMD78, surface roughness of the wetted surfaces ≤ 0.8 μm as standard. Lower surface roughness on
request.

Version Material TK Process Weight of two

diaphragm seals

[mbar/10 K] [kg]

WH AISI 316L +1.64 5

50 Endress+Hauser
Deltabar S

Process connection FMD78 Taper adapter with coupling nut, DIN 11851 (dairy fitting)
with metallic measuring
diaphragms (continued)

40
f
m
k
dM
D
G
P01-FMD78xxx-06-09-xx-xx-007

Process connection FMD78, material AISI 316L/1.4435, surface roughness of the wetted surfaces ≤ 0.8 μm as standard.
Lower surface roughness on request.

Taper adapter Slotted nut Diaphragm seal

Ver- Nominal Nominal Diameter Adapter Thread Height Height max. TK Process Weight of
sion diameter pressure height Diaphragm two
diameter diaphragm
seals

D f G k m dM

[mm] [mm] [mm] [mm] [mm] [mbar/10 K] [kg]

MR DN 50 PN 25 68.5 11 Rd 78 x 1/6" 22 19 52 +0.90 2.2

MS DN 65 PN 25 86 12 Rd 95 x 1/6" 25 21 66 +0.29 4.0

MT DN 80 PN 25 100 12 Rd 110 x 1/4" 30 26 81 +0.30 5.1

Threaded adapter, DIN 11851 (dairy fitting)

h

dM
d1
G
P01-FMD78xxx-06-09-xx-xx-008

Process connection FMD78, material AISI 316L/1.4435, surface roughness of the wetted surfaces ≤ 0.8 μm as standard.
Lower surface roughness on request.

Threaded adapter Diaphragm seal

Version Nominal Nominal Diameter Height Thread max. TK Process Weight of two
diameter pressure Diaphragm diaphragm
diameter seals

d1 h G dM

[mm] [mm] [mm] [mbar/10 K] [kg]

M3 DN 50 PN 25 54 35 Rd 78 x 1/6" 52 +0.95 1.8

M4 DN 65 PN 25 71 40 Rd 95 x 1/6" 66 +0.29 3.4

M5 DN 80 PN 25 85 40 Rd 110 x 1/4" 81 +0.19 4.0

Endress+Hauser 51
 Deltabar S

Process connection FMD78 EN/DIN flanges, connection dimensions as per EN 1092-1/DIN 2527
with metallic measuring JIS flanges, connection dimensions as per JIS B 2220
diaphragms (continued)

g2

b
dM

2
g

k
D

P01-FMD78xxx-06-09-xx-xx-009

Process connection FMD78, EN/DIN flange, Material AISI 316L

EN/DIN flange Boltholes Diaphragm seal

Ver- Nominal Nominal Shape 1 Dia- Thick- Raised Quan- Dia- Hole max. TK Weight of
sion diameter pressure meter ness face tity meter circle Diaphragm Process two
diameter diaphragm
seals

D b g g2 k dM

[mm] [mm] [mm] [mm] [mm] [mm] [mbar/10 K] [kg]

B3 DN 50 PN 10-40 B1 (D) 165 20 102 4 18 125 59 +1.50 6.0

B5 DN 80 PN 10-40 B1 (D) 200 24 138 8 18 160 89 +0.20 10.5

BT DN 100 PN 10-16 B1 (C) 220 20 – 8 18 180 89 +0.35 9.5

B6 DN 100 PN 25-40 B1 (D) 235 24 162 8 22 190 89 +0.19 13.3

1) Designation as per DIN 2527 in brackets

JIS flange Boltholes Diaphragm seal

Ver- Nominal Nominal Diameter Thickness Raised Quantity Diameter Hole max. TK Weight of
sion diameter pressure face circle Diaphragm Process two
diameter diaphragm
seals

D b g g2 k dM

[mm] [mm] [mm] [mm] [mm] [mm] [mbar/10 K] [kg]

KF 50 A 10 K 155 16 96 4 19 120 59 +0.81 4.6

KL 80 A 10 K 185 18 127 8 19 150 89 +0.19 7.0

KH 100 A 10 K 210 18 151 8 19 175 89 +0.25 9.4

52 Endress+Hauser
Deltabar S

Process connection FMD78 ANSI flanges, connection dimensions as per ANSI B 16.5, raised face RF
with metallic measuring
diaphragms (continued)
g2

b
dM

1.6 mm
0.06 in

L
g

k d3

D g

P01-FMD78xxx-06-09-xx-xx-010

Process connection FMD78, ANSI flange with and without extended diaphragm seal, material AISI 316/AISI 316L

Flange Boltholes Diaphragm seal

Ver- Nominal Class Dia- Thick- Raised Exten- Exten- Quan- Dia- Hole max. Dia- TK Weight of
sion dia- meter ness face sion sion tity meter circle phragm Process two dia-
meter length dia- diameter phragm
meter seals

D b g L d3 g2 k dM
[lb/sq.in] [in] [in] [in] [in] [in] [in] [in] [in] [mbar/ [kg]
[mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] 10 K]

AF 2 150 6 0.75 3.62 – – 4 0.75 4.75 2.32 +1.10 5.2

152.4 19.1 91.9 19.1 120.7 59

AR 2 300 6.5 0.88 3.62 – – 8 0.75 5 2.32 +0.75 6.8

165.1 22.5 91.9 19.1 127 59
AG 3 150 7.5 0.94 5 – – 4 0.75 6 3.50 +0.40 10.2
190.5 23.9 127 19.1 152.4 89

AS 3 300 8.25 1.12 5 – – 8 0.88 6.62 3.50 +0.35 14

209.5 28.4 127 22.4 168.1 89

J4 3 150 7.5 0.94 5 2 3 4 0.75 6 2.83 +0.29 12

190.5 23.9 127 50.8 76 19.1 152.4 72
4 13.2
101.6

6 14.2
152.4

8 15.4
203.6
AH 4 150 9 0.94 6.19 – – 8 0.75 7.5 3.50 +0.25 14.4
228.6 23.9 157.2 19.1 190.5 89

AT 4 300 10 1.25 6.19 – – 8 0.88 7.88 3.50 +0.19 23.4

254 31.8 157.2 22.4 200.1 89

J5 4 150 9 0.94 6.19 2 3.7 8 0.75 7.5 3.50 +0.19 17.3

228.6 23.9 157.2 50.8 94 19.1 190.5 89
4 19.8
101.6

6 22.3
152.4

8 24.8
203.6

Endress+Hauser 53
 Deltabar S

"Separate housing" version

101 84 118

131
45.5
ø51.7
P01-xxxxxxxx-06-xx-xx-xx-000

Dimensions T14 housing, optional display on the side. Housing weight see page 55.

101 76 118
147
45.5

ø51.7
P01-xxxxxxxx-06-xx-xx-xx-001

Dimensions T17 housing, optional display on the side. Housing weight see page 55.

r ³ 120 mm T17 r ³ 120 mm r ³ 120 mm

T14
55
55

ø54.1

➀ ➀ ➀
71

+– +– +– +– +–

P01-xxxxxxxx-06-xx-xx-xx-002

Reduction of the mounting height of the process connection, for application of the separate housing.
1 Process connection adapter.

If the separate housing is used, the mounting height of the process connection is reduced by approx. 55 mm
as compared to the dimensions of the standard version.
The minimum bending radius (r) for the cable is 120 mm (4.7").

54 Endress+Hauser
Deltabar S

Weight Housing

T14 T15 T17 Separate housing

Aluminium AISI 316L Aluminium AISI 316L

with electronic insert 1.2 kg 2.1 kg 1.8 kg 1.2 kg

and display Weight of housing T14, T15 or T17 + 0,5 kg.
with electronic insert 1.1 kg 2.0 kg 1.7 kg 1.1 kg Weight of sensor + 0,5 kg.
without display

Process connections
• Process connections PMD70 with ceramic measuring diaphragms: ab Seite 35 ff
• Process connections PMD75 with metallic measuring diaphragms: ab Seite 37 ff
• Process connection FMD76 with ceramic measuring diaphragms: ab Seite 40 ff
• Process connections FMD77 with metallic measuring diaphragms, low-pressure side: ab Seite 42 ff
• Process connection FMD78 with metallic measuring diaphragms: ab Seite 47 ff

Material T14/T15 housing:

• T14 housing, selectable:
– Die-cast aluminium with protective powder-coating on polyester basis: RAL 5012 (blue),
cover: RAL 7035 (grey)
– Precision cast stainless steel AISI 316L (1.4435)
• T15 housing: Die-cast aluminium with protective powder-coating on polyester basis: RAL 5012 (blue),
cover: RAL 7035 (grey)
• External operation (keys and key covering): Polycarbonate PC-FR,
RAL 7035 (grey)
• Sight glass: Mineral glass
• Cable gland: Polyamid (PA)
• Pressure compensation filter: PA6 GF10
• Bind plug: PBT-GF30 FR, for Dust Ex, EEx d, FM XP and CSA XP: AISI 316L (1.4435)
• Seals:
– Cable and blind plug seal: Silicone (VMQ)
– Pressure compensation filter o-ring: Silicone (VMQ)
– Cover: EPDM
– Sight glass: Silicone (VMQ)
• Nameplates: AISI 304 (1.4301)
T17 housing:
• Housing: Stainless steel AISI 316L (1.4404)
• Sight glass:
– Version for non-hazardous area, ATEX EEx ia, NEPSI Zone 0/1 Ex ia, IECEx Zone 0/1 Ex ia, FM NI, FM
IS, CSA IS: Polycarbonate (PC)
– ATEX 1/2 D, ATEX 1/3 D, ATEX 1 GD, ATEX 1/2 GD, ATEX 3 G, FM DIP, CSA Dust Ex: Mineral glass
• Cable gland: Polyamid (PA), for Dust-Ex: CuZn nickel-plated
• Blind plug: PBT-GF30 FR, for Dust-Ex: AISI 316L (1.4435)
• Pressure compensation filter: PA6 GF10
• Seals:
– Cable and blind plug seal: Silicone (VMQ)
– Pressure compensation filter o-ring: Silicone (VMQ)
– Cover: EPDM
– Sight glass: EPDM
• Nameplates: lasered

DIN/EN flanges
Endress+Hauser supplies DIN/EN flanges made of stainless steel AISI 316L with the material number 1.4435
or 1.4404. With regard to its stability property, the material 1.4435 is identical to 1.4404 which is grouped
under 13EO in EN 1092-1 Tab. 18. The chemical composition of the two materials can be identical.

Endress+Hauser 55
 Deltabar S

Cable for separate housing:

• PE cable:
Slip-resistant cable with strain-relief members made of Dynemo; shielded using aluminium-coated film;
insulated with polyethylene (PE-LD), black; copper wires, twisted, UV resistant
• FEP cable:
Slip-resistant cable; shielded using galvanized steel wire netting; insulated with fluorinated ethylene
propylene (FEP), black; copper wires, twisted, UV resistant
Miscellaneous:
• Measuring cell PMD70/FMD76, filling oil
– 25 mbar and 100 mbar measuring cell: Silicone oil
– 500 mbar and 3000 mbar measuring cell: Mineral oil
– for oxygen and ultra pure gas applications: Inert oil (Voltalef 1A)
• Measuring cell PMD75/FMD77 and FMD78, filling oil (Silicone oil)
– for oxygen and ultra pure gas applications: Inert oil (Halocarbon 6.3)
• Membrane material:
– PMD70/FMD76: Al2O3 (Aluminium-oxide-ceramic)
– PMD75, FMD77, FMD78:
– AISI 316L (1.4435)
– Alloy C276 (2.4819)
– Monel 400 (2.4360)
– Tantal
– AISI 316L (1.4435) with Gold-Rhodium coating (FMD77/FMD78 only)
– AISI 316L (1.4435) with 0.09 mm PTFE foil (FMD77/FMD78 only)
• Process diaphragm PMD70/FMD76: Al2O3 (Aluminium-oxide-ceramic)
• Mounting accessories: mounting bracket with screws AISI 304 (1.4301)
• Capillary: AISI 316 Ti (1.4571)
• Protective hose for capillary: AISI 304 (1.4301)
• External earth terminal: AISI 304 (1.4301)
• Screws and nuts for side flanges:
– PMD70: hex.-headed bolt DIN 931-M10x50-A2-70, hex.-headed nut: DIN 934-M10-A4-70
– PMD75 PN 160: hex.-headed bolt ISO 4014-M12x90-A4
– PMD75 PN 420: hex.-headed nut ISO 4032-M12-A4-bs
→ For process connections, seals and filling oils see ordering information, page 53 ff.

56 Endress+Hauser
Deltabar S

Planning instructions, diaphragm seal systems

Applications Diaphragm seal systems should be used if the process media and the device should be separated. Diaphragm
seal systems offer clear advantages in the following instances:
• In the case of high process temperatures (→ See also page 32, section "Process temperature limits".)
• In the case of process media that crystallise
• In the case of corrosive or highly various process media or process media with solids content
• In the case of heterogeneous and fibrous process media
• If good and rapid measuring point cleaning is necessary
• If the measuring point is exposed to vibrations
• For mounting locations that are difficult to access

Design and operation mode Diaphragm seals are separating equipment between the measuring system and the process medium.
A diaphragm seal system consists of:
• A diaphragm seal in a one-sided system, e.g. FMD77 or two diaphragm seals, in a two-sided system, e.g.
FMD78
• One capillary tube or two capillary tubes
• Fill fluid and
• A differential pressure transmitter.
The process pressure acts via the diaphragm seal membrane on the liquid-filled system, which transfers the
process pressure via the capillary tube onto the sensor of the differential pressure transmitter.
Endress+Hauser delivers all diaphragm seal systems as welded versions. The system is hermetically sealed,
which ensures the highest reliability.
Note!
The correlations between the individual diaphragm seal components are presented in the following section.
For further information and comprehensive diaphragm seal system designs, please contact your local
Endress+Hauser Sales Center.

Diaphragm seal
The diaphragm seal determines the application range of the system by
• the diaphragm diameter
• the diaphragms: stiffness and material
• the design (oil volume).

Diaphragm diameter
The larger the diaphragm diameter (less stiffness), the smaller the temperature effect on the measurement
result.
Note: To keep the temperature effect in practice-oriented limits, you should select diaphragm seals with a
nominal diameter of ≥ DN 80, in as far as the process connection allows for it.

Diaphragm stiffness
The stiffness is dependent on the diaphragm diameter, the material, any available coating and on the diaphragm
thickness and shape. The diaphragm thickness and the shape are defined constructively. The stiffness of a
diaphragm seal membrane influences the temperature operating range and the measuring error caused by
temperature effects.

Capillary
Diaphragm seals are used with the following capillary internal diameters as standard:
• ≤ DN 50: 1 mm
• > DN 50: 2 mm
The capillary tube influences the TK zero point, the ambient temperature operating range and the response time
of a diaphragm seal system as a result of its length and internal diameter.
→ See also page 59 ff, sections "Influence of the temperature on the zero point", "Ambient temperature range"
and "Response time".
→ Observe the installation instructions regarding capillary tubes. See page 64 ff, section "Installation
instructions".

Endress+Hauser 57
 Deltabar S

Filling oil
When selecting the filling oil, fluid and ambient temperature as well as the operating pressure are of crucial
importance. Observe the temperatures and pressures during commissioning and cleaning. A further selection
criterion is the compatibility of the filling oil with the requirements of the process medium. For this reason,
only filling oils that are harmless to health are used in the food industry, such as vegetable oil or silicone oil. →
See also the following section "Diaphragm seal filling oils".
The filling oil used influences the TK zero point and the temperature operating range of a diaphragm seal system
and the response time. → See also page 59 ff, sections "Influence of the temperature on the zero point" and
"Response time".

Differential pressure transmitter

The differential pressure transmitter influences the temperature operating range, the TK zero point and the
response time as a result of the volume of its side flange and as a result of its volume change. The volume
change is the volume that has to be shifted to pass through the complete measuring range.
Differential pressure transmitters from Endress+Hauser are optimised with regard to minimum volume change
and side flange.

Diaphragm seal filling oils

Version 1 Filling oil Permissible Permissible Density Viscosity Coefficient TK Notes

temperature range at temperature range of thermal correction
0.05 bar ≤ pabs ≤ 1 bar at pabs ≥ 1 bar expansion factor

[g/cm3] [cSt at [1/K]

25°C
(77°F)]
FMD77: A Silicone oil –40...+180°C –40...+250°C 0.96 100 0.00096 1 suitable for foods
FMD78: A, 1 (–40...+356°F) (–40...+482°F) FDA 21 CFR 175.105

FMD77: V High- –10...+200°C –10...+400°C 1.07 37 0.0007 0.72 high temperatures

FMD78: C, 3 temperature oil (+14...+392°F) (+14...+752°F)

FMD77: F Inert oil –40...+80°C –40...+175°C 1.87 27 0.000876 0.91 Oil for ultra pure gas
FMD78: D, 4 (–40...+176°F) (–40...+347°F) and oxygen
applications

FMD77: D Vegetable oil –10...+120°C –10...+200°C 0.94 9.5 0.00101 1.05 suitable for foods
FMD78: B, 2 (+14...+248°F) (+14...+392°F) FDA 21 CFR 172.856

FMD77: L Low –70...+80°C2 –70...+180°C2 0.92 4.4 – – low temperatures

FMD78: E, 5 temperature oil (–94...176°F) (–94...+356°F)

1) Version for feature 90 in the order code

2) Observe temperature limits of the device (→ page 31 and page 32)

58 Endress+Hauser
Deltabar S

Influence of the temperature A temperature change results in a volume change of the filling oil. The volume change is dependent on the
on the zero point coefficient of thermal expansion of the filling oil and on the volume of the filling oil at calibration temperature
(constant in the range: +21 to +33°C (+69.8 to 91.4°F)). → See also page 46, section "Diaphragm seal filling
oils".
For example, the filling oil expands in the event of a temperature increase. The additional volume presses
against the diaphragm seal membrane. The stiffer a diaphragm is, the greater its return force, which counteracts
a volume change and acts on the measuring cell together with the operating pressure, thus shifting the zero
point. For the "TK Process", see page 47 ff, section "Process connections FMD78".
The following diagrams display the temperature coefficient "TK Ambient" dependent on the capillary length.
The following application is displayed: capillary temperature and transmitter temperature (ambient
temperature) change, the process temperature corresponds to the calibration temperature.
The temperature coefficients obtained from the diagrams apply to silicone oil and the membrane material
AISI 316L/1.4435. For other filling oils, these temperature coefficients must be multiplied by the TK correction
factor of the corresponding filling oil. For the TK correction factors, see page 58, section "Diaphragm seal filling
oils".

TK Ambient 12
[mbar/10 K] 7
6
10

5
6
4
3
4

2
2
mbar
1.4 1
10 K

0
0 1 2 3 4 5 6 7 8 9 10
Capillary length
[m]
P01-FMD78xxx-05-xx-xx-xx-004

Example for:
– Diaphragm seal versions "B5, EN/DIN Flange DN 80 PN 10-40 B1, AISI 316L"
– Capillary length: 5 m
– Ambient temperature, capillary/transmitter: 45°C
– Filling oil: silicone oil
1. Select characteristic curve type for the diaphragm seal versions "B5" in accordance with the following
table.
Result: characteristic curve type 2
2. Obtain value for TK Ambient from the diagram.
Result: 1.4 mbar/10 K
3. TAmbient – TCalibration = 45°C – 25°C = 20°C ⇒ 1.4 mbar/10 K x 20 K = 2.8 mbar
Result: In this application, the zero point is shifted by 2.8 mbar.
Note!
• The influence of temperature on the zero point can be corrected with position calibration.
• The temperature influence can be minimised by using a filling oil with a smaller coefficient of thermal
expansion, shorter capillaries, diaphragm seals with larger diaphragm diameter or by using a smaller capillary
internal diameter.

Endress+Hauser 59
 Deltabar S

Characteristic Version Diaphragm seal

type
1 TF Tri-Clamp, ISO 2852 DN 76.1 (3"), AISI 316L/1.4435
2 GA Thread ISO 228 G 1/2 B, PN 40, AISI 316L, Separator, PTFE seal
RL Thread ANSI 1/2 FNPT, PN 40, AISI 316L, Separator, PTFE seal
UH Cell DN 80 PN 16-400, AISI 316L
UJ Cell DN 100 PN 16-400, AISI 316L
VH Cell 3" 150-2500 lbs, AISI 316L
VJ Cell 4" 150-2500 lbs, AISI 316L
B5 EN/DIN flange DN 80 PN 10-40 B1, AISI 316L
BT EN/DIN flange DN 100 PN 10-16 B1, AISI 316L
B6 EN/DIN flange DN 100 PN 25-40 B1, AISI 316L
AG ANSI flange 3" 150 lbs RF, AISI 316/316L
AS ANSI flange 3" 300 lbs RF, AISI 316/316L
AH ANSI flange 4" 150 lbs RF, AISI 316/316L
J5 ANSI flange 4" 150 lbs RF, AISI 316/316L, Extensions: 2"/4"/6"/8"
AT ANSI flange 4" 300 lbs RF, AISI 316/316L
KL JIS flange 80 A 10 K RF, AISI 316L
KH JIS flange 100 A 10 K RF, AISI 316L
MT DIN 11851 DN 80 PN 25, AISI 316L
M5 DIN 11851 DN 80 PN 25 socket, AISI 316L
3 MS DIN 11851 DN 65 PN 25, AISI 316L
M4 DIN 11851 DN 65 PN 25 socket, AISI 316L
J4 ANSI flange 3" 150 lbs RF, AISI 316/316L, Extensions: 2"/4"/6"/8"
4 SC Pipe seal diaphragm Tri Clamp, ISO 2852 DN 38 (1 1/2"), AISI 316L/1.4435
SD Pipe seal diaphragm Tri Clamp, ISO 2852 DN 51 (2"), AISI 316L/1.4435
5 UF Cell DN 50 PN 16-400, AISI 316L
VF Cell 2" 150-2500 lbs, AISI 316L
B3 EN/DIN flange DN 50 PN 10-40 B1, AISI 316L
AF ANSI flange 2" 150 lbs RF, AISI 316/316L
AR ANSI flange 2" 300 lbs RF, AISI 316/316L
KF JIS flange 50 A 10 K RF, AISI 316L
MR DIN 11851 DN 50 PN 25, AISI 316L
M3 DIN 11851 DN 50 PN 25 socket, AISI 316L
6 TD Tri-Clamp, ISO 2852 DN 51 (2"), DIN 32676 DN 50, AISI 316L/1.4435
7 TK DRD DN50 (65 mm), PN 25, AISI 316L/1.4435
TR Varivent Type N for tubes DN 40 – DN 162, PN 40, AISI 316L/1.4435

TK Ambient 90
[mbar/10 K]
80

70
11
60

50

40
10
30
9
20
8
10

0
0 1 2 3 4 5 6 7 8 9 10

Capillary length
[m]
P01-FMD78xxx-05-xx-xx-xx-005

60 Endress+Hauser
Deltabar S

Characteristic Version Diaphragm seal

type
8 SB Pipe seal diaphragm Tri-Clamp, ISO 2852 DN 25 (1"), AISI 316L/1.4435
9 WH Sanitary tank spud, AISI 316L/1.4435, Extensions 2"
10 TC Tri-Clamp, ISO 2852 DN 38 (1 – 1 1/2"), DIN 32676 DN 40, AISI 316L/1.4435
11 TB Tri-Clamp, ISO 2852 DN 25 (1"). DIN 32676 DN 25, AISI 316L/1.4435

Ambient temperature range The filling oil, capillary length, capillary internal diameter, process temperature and the oil volume of the
diaphragm seal determine the ambient temperature operating range of the diaphragm seal system.
The following diagrams display the permitted ambient temperature operating range in relation to the capillary
length. The diagrams apply to a process temperature of +25°C (+77°F) and to silicone oil.
The operating range can be extended by using a filling oil with a smaller coefficient of expansion and by using
shorter capillaries.
Note!
• Endress+Hauser recommends using low temperature oil for applications that require short response times or
that are near the lower temperature limit. → See also page 58, "Diaphragm seal filling oils" section.
• For further information, comprehensive diaphragm seal system designs and measuring technology solutions
acting close to the operating limits, please contact your local Endress+Hauser Sales Center.

Group A Group B
80 80
Ambient temperature [°C]

Ambient temperature [°C]

60 60
40 40
20 permitted 20 permitted
operating range operating range
0 0
–20 –20
–40 –40
0 1 2 3 4 5 6 7 8 9 10 0 1 2 3 4 5 6 7 8 9 10
Capillary length [m] Capillary length [m]
P01-FMD78xxx-05-xx-xx-xx-006 P01-FMD78xxx-05-xx-xx-xx-007

Group C Group D
80 80
Ambient temperature [°C]

Ambient temperature [°C]

60 60
40 40
20 permitted 20 permitted
operating range operating range
0 0
–20 –20
–40 –40
0 1 2 3 4 5 6 7 8 9 10 0 1 2 3 4 5 6 7 8 9 10
Capillary length [m] Capillary length [m]
P01-FMD78xxx-05-xx-xx-xx-009 P01-FMD78xxx-05-xx-xx-xx-008

Group E Group F
80 80
Ambient temperature [°C]

Ambient temperature [°C]

60 60

40 40
permitted 20 permitted
20 operating range operating range
0 0

–20 –20

–40 –40
0 1 2 3 4 5 6 7 8 9 10 0 1 2 3 4 5 6 7 8 9 10
Capillary length [m] Capillary length [m]
P01-FMD78xxx-05-xx-xx-xx-015 P01-FMD78xxx-05-xx-xx-xx-013

Endress+Hauser 61
 Deltabar S

Group G Group H
80 80
Ambient temperature [°C]

Ambient temperature [°C]

60 60
40 40
permitted
20 permitted 20 operating range
operating range
0 0
–20 –20
–40 –40
0 1 2 3 4 5 6 7 8 9 10 0 1 2 3 4 5 6 7 8 9 10
Capillary length [m] Capillary length [m]
P01-FMD78xxx-05-xx-xx-xx-012 P01-FMD78xxx-05-xx-xx-xx-011

Group I Group J
80 80
Ambient temperature [°C]

Ambient temperature [°C]

60 60
permitted
40 operating range 40 permitted
operating range
20 20
0 0
–20 –20
–40 –40
0 1 2 3 4 5 6 7 8 9 10 0 1 2 3 4 5 6 7 8 9 10
Capillary length [m] Capillary length [m]
P01-FMD78xxx-05-xx-xx-xx-010 P01-FMD78xxx-05-xx-xx-xx-014

Group Version Diaphragm seal

A SB Pipe seal diaphragm Tri-Clamp, ISO 2852 DN 25 (1"), AISI 316L/1.4435

SC Pipe seal diaphragm Tri Clamp, ISO 2852 DN 38 (1 1/2"), AISI 316L/1.4435
SD Pipe seal diaphragm Tri Clamp, ISO 2852 DN 51 (2"), AISI 316L/1.4435
GA Thread ISO 228 G 1/2 B, PN 40, AISI 316L, Separator, PTFE seal
RL Thread ANSI 1/2 FNPT, PN 40, AISI 316L, Separator, PTFE seal
B UF Cell DN 50 PN 16-400, AISI 316L
VF Cell 2" 150-2500 lbs, AISI 316L
B3 EN/DIN flange DN 50 PN 10-40 B1, AISI 316L
AF ANSI flange 2" 150 lbs RF, AISI 316/316L
AR ANSI flange 2" 300 lbs RF, AISI 316/316L
KF JIS flange 50 A 10 K RF, AISI 316L
MR DIN 11851 DN 50 PN 25, AISI 316L
M3 DIN 11851 DN 50 PN 25 socket, AISI 316L
C UH Cell DN 80 PN 16-400, AISI 316L
UJ Cell DN 100 PN 16-400, AISI 316L
VJ Cell 4" 150-2500 lbs, AISI 316L
B5 EN/DIN flange DN 80 PN 10-40 B1, AISI 316L
BT EN/DIN flange DN 100 PN 10-16 B1, AISI 316L
B6 EN/DIN flange DN 100 PN 25-40 B1, AISI 316L
AH ANSI flange 4" 150 lbs RF, AISI 316/316L
J5 ANSI flange 4" 150 lbs RF, AISI 316/316L, Extensions: 2"/4"/6"/8"
AT ANSI flange 4" 300 lbs RF, AISI 316/316L
KH JIS flange 100 A 10 K RF, AISI 316L
MT DIN 11851 DN 80 PN 25, AISI 316L
M5 DIN 11851 DN 80 PN 25 socket, AISI 316L
D VH Cell 3" 150-2500 lbs, AISI 316L
AG ANSI flange 3" 150 lbs RF, AISI 316/316L
AS ANSI flange 3" 300 lbs RF, AISI 316/316L
KL JIS flange 80 A 10 K RF, AISI 316L
TD Tri-Clamp, ISO 2852 DN 51 (2"), DIN 32676 DN 50, AISI 316L/1.4435
TF Tri-Clamp, ISO 2852 DN 76.1 (3"), AISI 316L/1.4435
E J4 ANSI flange 3" 150 lbs RF, AISI 316/316L, Extensions: 2"/4"/6"/8"
F TK DRD DN50 (65 mm), PN 25, AISI 316L/1.4435
TR Varivent Type N for tubes DN 40 – DN 162, PN 40, AISI 316L/1.4435
G MS DIN 11851 DN 65 PN 25, AISI 316L
M4 DIN 11851 DN 65 PN 25 socket, AISI 316L
H TC Tri-Clamp, ISO 2852 DN 38 (1 – 1 1/2"), DIN 32676 DN 40, AISI 316L/1.4435
I TB Tri-Clamp, ISO 2852 DN 25 (1"). DIN 32676 DN 25, AISI 316L/1.4435
J WH Sanitary tank spud, AISI 316L/1.4435, Extensions 2"

62 Endress+Hauser
Deltabar S

Response time The viscosity of the filling oil, the capillary length and the capillary internal diameter influence the frictional
resistance. The greater the frictional resistance, the longer the response time.
Furthermore, the volume change of the measuring cell influences the response time. The lower the
volume change of the measuring cell is, the less filling oil has to be shifted in the diaphragm seal system.
The following diagram shows typical response times (T90) for the various filling oils dependent on the
measuring cell and the capillary internal diameter. The values given are in seconds per metre of capillary length
and must be multiplied by the actual length of the capillary. The response time of the transmitter must also be
taken into consideration.

Ambient temperature range = 20°C

Response time (T90) [sec/m] 8

6
Silicone oil
4 High temperature oil
Vegetable oil
Inert oil
2

0
DN 50 DN 80 DN 50 DN 80 Nominal diameter
(1 mm) (2 mm) (1 mm) (2 mm) Capillary internal diameter
500 mbar 3 bar Measuring cell
P01-FMD78xxx-05-xx-xx-xx-000

100 %
➀
90 %

T90 t

P01-xxxxxxxx-05-xx-xx-xx-006

Presentation of the response time (T90%)

1 Pressure step
2 Output signal

Minimise response time by Comments

Larger capillary internal diameter The temperature effect increases with increasing diameter.
Shorter capillaries –

Filling oil with lower viscosity – Observe compatibility of the filling oil with the process
fluid.
– Observe the filling oil operating limits.

Endress+Hauser 63
 Deltabar S

Installation instructions Instructions for diaphragm seal systems

• The diaphragm seal together with the transmitter form a closed, calibrated system, which is filled through
ports in the diaphragm seal and in the measuring system of the transmitter. These ports are sealed and must
not be opened.
• In the case of devices with diaphragm seals and capillaries, the zero point shift caused by the hydrostatic
pressure of the filling liquid column in the capillaries must be taken into account when selecting the
measuring cell. If a measuring cell with a small measuring range is selected, the sensor nominal range can
be overdriven as a result of position adjustment. → See the following diagram and the following example.
• For devices with capillary a suitable fastening device (mounting bracket) is recommended.
• When using a mounting bracket, sufficient strain relief must be allowed for in order to prevent the capillary
bending down (bending radius ≥ 100 mm).
• The temperature and length of both capillaries should be the same when using two-sided diaphragm seal
systems.

Selecting the measuring cell (observe the hydrostatic pressure of the filling fluid column in the capillaries!)

pi
–

Capillaries with silicone oil

max. ρFl = 0.96 kg/dm3

ΔH = 1 m Hv = 1.8 m

min. +
Hu = 0.2 m

H1 = 0.3 m
+ –

Tank with water

ρM = 1.0 kg/dm3
P01-FMD78xxx-11-xx-xx-xx-004.eps

Pressure on the negative side of the differential pressure transmitter (p–) when the tank is empty (min. level)

p–= pHv+ pH1 = Hv • ρ Fl • g + H1 • ρFl • g + p i

kg kg
= 1.8 m • 0.96 • 9.81 m m
s + 0.3 m • 0.96 dm3 • 9.81 s + pi
dm3
= 197.77 mbar + p i

Pressure on the positive side of the differential pressure transmitter (p+) when the tank is empty (min. level)

p+= pHu+ pH1 = Hu • ρM • g + H1 • ρFl • g + pi

kg kg
= 0.2 m • 1 • 9.81 m m
s + 0.3 m • 0.96 dm3 • 9.81 s + pi
dm3
= 47.87 mbar + pi

Differential pressure at the transmitter (ΔpTransmitter) when the tank is empty

64 Endress+Hauser
Deltabar S

Result:
If the tank were full, a differential pressure of –51.80 mbar would be present at the differential pressure transmitter. When
the tank is empty, a differential pressure of –149.90 mbar is present. Therefore, a 500 mbar measuring cell is required for
this application.

Installation instructions
In order to obtain more precise measurement results and to avoid a defect in the device, mount the capillaries
as follows:
• vibration-free (in order to avoid additional pressure fluctuations)
• not in the vicinity of heating or cooling lines
• insulate if the ambient temperature is below ore above the reference temperature
• with a bending radius of ≥ 100 mm.

Vacuum applications
For applications under vacuum, Endress+Hauser recommends mounting the pressure transmitter underneath
the lower diaphragm seal. A vacuum load of the diaphragm seal caused by the presence of filling oil in the
capillaries is hereby prevented.
When the pressure transmitter is mounted above the lower diaphragm seal, the maximum height difference
H1 in accordance with the following illustration on the left must not be exceeded. The maximum height
difference is dependent on the density of the filling oil and the smallest ever pressure that is permitted to occur
at the diaphragm seal on the positive side (empty tank), see the following illustration, on the right.

12.0
Low temperature oil
10.0
Height difference H1 [m]
Vegetable oil

8.0
– Silicone oil
6.0
High temperature
– + oil
+ –
4.0

H1 Inert oil
2.0
+
0.0
50 100 200 300 400 500 600 700 800 900 1000
Pressure, diaphragm seal positive side [mbarabs]

P01-FMD7xxxx-11-xx-xx-xx-001 P01-FMD7xxxx-05-xx-xx-xx-002

Installation above the lower diaphragm seal Diagram of maximum installation height above the lower diaphragm
seal for vacuum applications dependent on the pressure at the
diaphragm seal on the positive side

Endress+Hauser 65
 Deltabar S

Certificates and approvals

CE mark The device meets the legal requirements of the relevant EC directives. Endress+Hauser confirms that the
device has been successfully tested by applying the CE mark.

Ex approvals • ATEX
• FM
• CSA
• NEPSI
• IECEx
• GOST on request
• also combinations of different approvals
All explosion protection data are given in separate documentation which is available upon request. The Ex
documentation is supplied as standard with all devices approved for use in explosion hazardous areas.
→ See also page 81 ff, sections "Safety Instructions" and "Installation/Control Drawings".

Marine certificate • GL: FMD76, FMD78, PMD70, PMD75

• ABS: FMD76, FMD78, PMD70, PMD75

Overspill protection WHG (German Water Resources Act). See "Ordering information" → ä 67 (see also ZE259P/00/de).

CRN approvals Some device versions have CRN approval. For a CRN-approved device, a CRN-approved process connection
(→ see page 68, feature 70 "Process connection") has to be ordered with a CSA approval (→ see page 67,
feature 10 "Approval"). These devices are fitted with a separate plate bearing the registration number
0F10524.5C.

Pressure Equipment Directive The devices PMD70, PMD75, FMD76, FMD77 und FMD78 corresponds to Article 3 (3) of the EC directive
(PED) 97/23/EC (Pressure Equipment Directive) and has been designed and manufactured according to good
engineering practice.
Additionally applies:
– FMD78 with pipe diaphragm seal ≥ 1.5"/PN40:
Suitable for stable gases in group 1, category II
– PMD75, PN 420
Suitable for stable gases in group 1, category I

Standards and guidelines DIN EN 60770 (IEC 60770):

Transmitters for use in industrial-process control systems
Part 1: Methods for inspection and routine testing
DIN 16086:
Electrical pressure measuring instruments, pressure sensors, pressure transmitters, pressure measuring
instruments, concepts, specifications in data sheets
EN 61326-X:
EMC product family standard for electrical equipment for measurement, control and laboratory use.

66 Endress+Hauser
Deltabar S

Ordering information
PMD70 This overview does not mark options which are mutually exclusive.

10 Approval:
A For non-hazardous areas
1 ATEX II 1/2 G EEx ia IIC T6
6 ATEX II 1/2 G EEx ia IIC T6, overspill protection WHG
➀ 2 ATEX II 1/2 D
4 ATEX II 1/3 D
8 ATEX II 1 GD EEx ia IIC T6
3 ATEX II 1/2 GD EEx ia IIC T6

– + E
➁ 7 ATEX II 3 G EEx nA II T6
S FM IS, Class I, II, III Division 1, Groups A – G; NI Class I Division 2, Groups A – D; AEx ia
Q FM DIP, Class II, III Division 1, Groups E – G
R FM NI, Class I, Division 2, Groups A – D
U CSA IS, Class I, II, III Division 1, Groups A – G; Class I Division 2, Groups A – D, Ex ia
W CSA Class II, III Division 1, Groups E – G (Dust-Ex)
H NEPSI Ex ia IIC T6
I IECEx Zone 0/1 Ex ia IIC T6

20 Output; Operation:
➂ A 4...20 mA HART, SIL operation outside, LCD (→ see Fig. ➀, o)
B 4...20 mA HART, SIL operation inside, LCD (→ see Fig. ➀, p)
➃ C 4...20 mA HART, SIL operation inside (→ see Fig. p)
M PROFIBUS PA, operation outside, LCD (→ see Fig. ➀, o)
1 2
N PROFIBUS PA, operation inside, LCD (→ see Fig. ➀, p)
PC

HART
R
O PROFIBUS PA, operation inside (→ see Fig. p)
250002271-–

FIELD COMMUNICATION PROTOCOL

P FOUNDATION Fieldbus, operation outside, LCD (→ see Fig. n, o)

HW-Version: 1
SW-Version: 2

Q FOUNDATION Fieldbus, operation inside, LCD (→ see Fig. n, p)

R FOUNDATION Fieldbus, operation inside (→ see Fig. p)

30 Housing; Cable entry; Protection:

T14 A Aluminium T14 housing, optional display on the side, IP 66/67/NEMA 6P, Gland M 20x1.5
B Aluminium T14 housing, optional display on the side, IP 66/67/NEMA 6P, Thread G 1/2
T15 C Aluminium T14 housing, optional display on the side, IP 66/67/NEMA 6P, Thread 1/2 NPT
D Aluminium T14 housing, optional display on the side, IP 66/67/NEMA 6P, M12x1 PA plug
E Aluminium T14 housing, optional display on the side, IP 66/67/NEMA 6P, 7/8" FF plug
F Aluminium T14 housing, optional display on the side, IP 65/NEMA 4X, Han7D plug, 90°
J Aluminium T15 housing, optional display on the top, IP 66/67/NEMA 6P, Gland M 20x1.5
K Aluminium T15 housing, optional display on the top, IP 66/67/NEMA 6P, Thread G 1/2
L Aluminium T15 housing, optional display on the top, IP 66/67/NEMA 6P, Thread 1/2 NPT
T17 M Aluminium T15 housing, optional display on the top, IP 66/67/NEMA 6P, M12x1 PA plug
N Aluminium T15 housing, optional display on the top, IP 66/67/NEMA 6P, 7/8" FF plug
P Aluminium T15 housing, optional display on the top, IP 65/NEMA 4X, Han7D plug, 90°
1 AISI 316L T14 housing, optional display on the side, IP 66/67/NEMA 6P, Gland M 20x1.5
2 AISI 316L T14 housing, optional display on the side, IP 66/67/NEMA 6P, Thread G 1/2
3 AISI 316L T14 housing, optional display on the side, IP 66/67/NEMA 6P, Thread 1/2 NPT
4 AISI 316L T14 housing, optional display on the side, IP 66/67/NEMA 6P, M 12x1 PA plug
5 AISI 316L T14 housing, optional display on the side, IP 66/67/NEMA 6P, 7/8" FF plug
6 AISI 316L T14 housing, optional display on the side, IP 65/NEMA 4X, Han7D plug, 90°
R AISI 316L T17 housing, optional display on the side, IP 66/68/NEMA 6P, Gland M 20x1.5
S AISI 316L T17 housing, optional display on the side, IP 66/68/NEMA 6P, Thread G 1/2
T AISI 316L T17 housing, optional display on the side, IP 66/68/NEMA 6P, Thread 1/2 NPT
U AISI 316L T17 housing, optional display on the side, IP 66/68/NEMA 6P, M 12x1 PA plug
V AISI 316L T17 housing, optional display on the side, IP 66/68/NEMA 6P, 7/8" FF plug
Z Housing: see additional specifications

40 Nominal range; PN:

Nominal value PN
7B 25 mbar/2500 Pa/0.375 psi 10 bar/1 MPa/150 psi
7D 100 mbar/10 kPa/1.5 psi 16 bar/1,6 MPa/240 psi
7F 500 mbar/50 kPa/7.5 psi 100 bar/10 MPa/1500 psi
7H 3 bar/300 kPa/45 psi 100 bar/10 MPa/1500 psi
78 Prepared mounting DELTATOP/DELTASET

PMD70 order code

→ For continuation of PMD70 ordering information, see the following page.

Endress+Hauser 67
 Deltabar S

PMD70 (continued) 50 Calibration; Unit:

1 Nominal range; mbar/bar
2 Nominal range; kPa/MPa
3 Nominal range; mmH2O/mH2O
4 Nominal range; inH2O/ftH2O
6 Nominal range; psi
8 Adjusted for Deltatop/Deltaset; see additional specification
B Customised; see additional specification
C Factory certificate 5-point; see additional specification
D DKD certificate; see additional specification
K Platinum; see additional specification
L Platinum and factory certificate 5-point; see additional specification
M Platinum and DKD certificate; see additional specification

70 Process connection; Material:

B 1/4 – 18 NPT IEC 61518, mounting: 7/16 – 20 UNF, C22.8 (CRN)
D 1/4 – 18 NPT IEC 61518, mounting: 7/16 – 20 UNF, AISI 316L (CRN)
F 1/4 – 18 NPT IEC 61518, mounting: 7/16 – 20 UNF, Alloy C (CRN)
G 1/4 – 18 NPT IEC 61518, mounting: 7/16 – 20 UNF, PVDF
U RC 1/4 mounting: 7/16 – 20 UNF, AISI 316L (CRN)
1 1/4 – 18 NPT, mounting: PN 160: M10, C22.8 (CRN)
2 1/4 – 18 NPT, mounting: PN 160: M10, AISI 316L (CRN)
3 1/4 – 18 NPT, mounting: PN 160: M10, Alloy C (CRN)

80 Seal:
A FKM Viton
B EPDM
D Kalrez
E Chemraz
1 FKM Viton, cleaned from oil and greace
2 FKM Viton, cleaned for oxygen service
Note application limits pressure/temp.

100 Additional option 1:

A not selected
E SIL2/IEC 61508 Declaration of conformity
B Material test certificate for wetted components, inspection certificate as per
EN 10204 3.1 acc. to specification 52005759
M Overvoltage protection
N HistoROM/M-DAT
S GL/ABS marine certificate
V Mounting on shut-off valve from above
W Mounting on shut-off valve from below
2 Test report acc. to EN10204 2.2
3 Routine test with certificate, inspection certificate as per EN 10204 3.1
4 Overpressure test with certificate,
inspection certificate as per EN 10204 3.1

110 Additional option 2:

A not selected
E SIL2/IEC 61508 Declaration of conformity
B Material test certificate for wetted components, inspection certificate as per
EN10204 3.1 acc. to specification 52005759
G Separate housing, cable length see additional spec. + mounting bracket,
wall/pipe, 316L
K Vent valves (2 pieces), Alloy C
M Overvoltage protection
N HistoROM/M-DAT
R Screws 7/16 UNF, length 1 1/2" (4 pieces) for oval flange adapter PZO
S GL/ABS marine certificate
U Mounting bracket for wall/pipe, AISI 304
2 Test report acc. to EN10204 2.2
3 Routine test with certificate, inspection certificate as per EN 10204 3.1
4 Overpressure test with certificate, inspection certificate as per EN 10204 3.1
5 Helium leak test EN 1518 with test certificate,
inspection certificate as per EN 10204 3.1
Z Special version, to be specified

PMD70 complete order code

68 Endress+Hauser
Deltabar S

PMD75 This overview does not mark options which are mutually exclusive.

10 Approval:
A For non-hazardous areas
1 ATEX II 1/2 G EEx ia IIC T6
6 ATEX II 1/2 G EEx ia IIC T6, overspill protection WHG
2 ATEX II 1/2 D
4 ATEX II 1/3 D
8 ATEX II 1 GD EEx ia IIC T6
3 ATEX II 1/2 GD EEx ia IIC T6
5 ATEX II 2 G EEx d IIC T6
7 ATEX II 3 G EEx nA II T6
S FM IS, Class I, II, III Division 1, Groups A – G; NI Class I Division 2, Groups A – D; AEx ia
T FM XP, Class I Division 1, Groups A – D; AEx d
Q FM DIP, Class II, III Division 1, Groups E – G

➀
R FM NI, Class I, Division 2, Groups A – D
U CSA IS, Class I, II, III Division 1, Groups A – G; Class I Division 2, Groups A – D, Ex ia
V CSA XP, Class I Division 1, Groups B – D; Ex d
W CSA Class II, III Division 1, Groups E – G (Dust-Ex)

– + E
➁ G
H
NEPSI Exd IIC T6
NEPSI Ex ia IIC T6
I IECEx Zone 0/1 Ex ia IIC T6
B Combined certificates: ATEX II 1/2 G EEx ia IIC T6 + II G EEx d IIC T6
C Combined certificates: FM IS and XP Class I Division 1, Groups A – D
D Combined certificates: CSA IS and XP Class I Division 1, Groups A – D
E Combined certificates: FM/CSA IS and XP Class I Division 1, Groups A – D
F Combined certificates: ATEX II EEx ia / EEx d + FM/CSA IS + XP; ATEX II 1/2G EEx ia IIC T6+; ATEX II 2G EEx d IIC
T6+; FM/CSA IS + XP Cl.I Div.1 Gr.A-D

20 Output; Operation:
➂ A 4...20 mA HART, SIL operation outside, LCD (→ see Fig. ➀, o)
B 4...20 mA HART, SIL operation inside, LCD (→ see Fig. ➀, p)
➃ C 4...20 mA HART, SIL operation inside (→ see Fig. p)
M PROFIBUS PA, operation outside, LCD (→ see Fig. ➀, o)
1 2
N PROFIBUS PA, operation inside, LCD (→ see Fig. ➀, p)
PC

HART
R
O PROFIBUS PA, operation inside (→ see Fig. p)
250002271-–

FIELD COMMUNICATION PROTOCOL

P FOUNDATION Fieldbus, operation outside, LCD (→ see Fig. n, o)

HW-Version: 1
SW-Version: 2

Q FOUNDATION Fieldbus, operation inside, LCD (→ see Fig. n, p)

R FOUNDATION Fieldbus, operation inside (→ see Fig. p)

30 Housing; Cable entry, Protection:

A Aluminium T14 housing, optional display on the side, IP 66/67/NEMA 6P, Gland M 20x1.5
T14
B Aluminium T14 housing, optional display on the side, IP 66/67/NEMA 6P, Thread G 1/2
C Aluminium T14 housing, optional display on the side, IP 66/67/NEMA 6P, Thread 1/2 NPT
D Aluminium T14 housing, optional display on the side, IP 66/67/NEMA 6P, M12x1 PA plug
T15 E Aluminium T14 housing, optional display on the side, IP 66/67/NEMA 6P, 7/8" FF plug
F Aluminium T14 housing, optional display on the side, IP 65/NEMA 4X, Han7D plug, 90°
J Aluminium T15 housing, optional display on the top, IP 66/67/NEMA 6P, Gland M 20x1.5
K Aluminium T15 housing, optional display on the top, IP 66/67/NEMA 6P, Thread G 1/2
L Aluminium T15 housing, optional display on the top, IP 66/67/NEMA 6P, Thread 1/2 NPT
M Aluminium T15 housing, optional display on the top, IP 66/67/NEMA 6P, M 12x1 PA plug
+ –

T17 N Aluminium T15 housing, optional display on the top, IP 66/67/NEMA 6P, 7/8" FF plug
P Aluminium T15 housing, optional display on the top, IP 65/NEMA 4X, Han7D plug, 90°
1 AISI 316L T14 housing, optional display on the side, IP 66/67/NEMA 6P, Gland M 20x1.5
2 AISI 316L T14 housing, optional display on the side, IP 66/67/NEMA 6P, Thread G 1/2
3 AISI 316L T14 housing, optional display on the side, IP 66/67/NEMA 6P, Thread 1/2 NPT
4 AISI 316L T14 housing, optional display on the side, IP 66/67/NEMA 6P, M 12x1 PA plug
5 AISI 316L T14 housing, optional display on the side, IP 66/67/NEMA 6P, 7/8" FF plug
6 AISI 316L T14 housing, optional display on the side, IP 65/NEMA 4X, Han7D plug, 90°
R AISI 316L T17 housing, optional display on the side, IP 66/68/NEMA 6P, Gland M 20x1.5
S AISI 316L T17 housing, optional display on the side, IP 66/68/NEMA 6P, Thread G 1/2
T AISI 316L T17 housing, optional display on the side, IP 66/68/NEMA 6P, Thread 1/2 NPT
U AISI 316L T17 housing, optional display on the side, IP 66/68/NEMA 6P, M 12x1 PA plug
V AISI 316L T17 housing, optional display on the side, IP 66/68/NEMA 6P, 7/8" FF plug
Z Housing: see additional specifications

PMD75 order code

→ For continuation of PMD75 ordering information, see the following page.

Endress+Hauser 69
 Deltabar S

PMD75 (continued) 40 Nominal range; PN:

Nominal value PN
7B 10 mbar/1 kPa/0.15 psi 160 bar/16 MPa/2400 psi
7C 30 mbar/3 kPa/0.45 psi 160 bar/16 MPa/2400 psi
7D 100 mbar/10 kPa/1.5 psi 160 bar/16 MPa/2400 psi
7F 500 mbar/50 kPa/7.5 psi 160 bar/16 MPa/2400 psi
7H 3 bar/300 kPa/45 psi 160 bar/16 MPa/2400 psi
7L 16 bar/1,6 MPa/240 psi 160 bar/16 MPa/2400 psi
7M 40 bar/4 MPa/600 psi 160 bar/16 MPa/2400 psi
8F 500 mbar/50 kPa/7.5 psi 420 bar/42 MPa/6300 psi
8H 3 bar/300 kPa/45 psi 420 bar/42 MPa/6300 psi
8L 16 bar/1.6 MPa/240 psi 420 bar/42 MPa/6300 psi
8M 40 bar/4 MPa/600 psi 420 bar/42 MPa/6300 psi
78 Prepared for Deltatop/Deltaset; PN = 160 bar
88 Prepared for Deltatop/Deltaset; PN = 420 bar

50 Calibration; Unit:
1 Nominal range; mbar/bar
2 Nominal range; kPa/MPa
3 Nominal range; mmH2O/mH2O
4 Nominal range; inH2O/ftH2O
6 Nominal range; psi
8 Adjusted for Deltatop/Deltaset; see additional specification
B Customised; see additional specification
C Factory certificate 5-point; see additional specification
D DKD certificate; see additional specification
K Platinum; see additional specification
L Platinum and factory certificate 5-point; see additional specification
M Platinum and DKD certificate; see additional specification

60 Membrane material:
1 AISI 316L
2 Alloy C
3 Monel
5 Tantal
6 AISI 316L with Gold-Rhodium coating

70 Process connection; Material:

B 1/4 – 18 NPT IEC 61518, mounting: 7/16 – 20 UNF, C22.8 (CRN),
including 2 vent valves (AISI 316L)
C 1/4 – 18 NPT IEC 61518, mounting: 7/16 – 20 UNF, C22.8, side vent,
including 4 fastening bolt connections and 2 vent valves (AISI 316L)
D 1/4 – 18 NPT IEC 61518, mounting: 7/16 – 20 UNF, AISI 316L (CRN),
including 2 vent valves (AISI 316L)
E 1/4 – 18 NPT IEC 61518, mounting: 7/16 – 20 UNF, AISI 316L, side vent,
including 4 fastening bolt connections and 2 vent valves (AISI 316L)
F 1/4 – 18 NPT IEC 61518, mounting: 7/16 – 20 UNF, Alloy C (CRN),
without screws/vents
H 1/4 – 18 NPT IEC 61518, mounting: 7/16 – 20 UNF, Alloy C,
side vent, without screws/vents
U RC 1/4 mounting: 7/16 – 20 UNF, AISI 316L (CRN),
including 2 vent valves (AISI 316L)
V RC 1/4 mounting: 7/16 – 20 UNF, C22.8, side vent,
including 4 fastening bolt connections and 2 vent valves (AISI 316L)
W Prepared for diaphragm seal mount
1 1/4 – 18 NPT, mounting: PN 160: M10, PN 420: M12, C22.8 (CRN),
including 2 vent valves (AISI 316L)
2 1/4 – 18 NPT, mounting: PN 160: M10, PN 420: M12, AISI 316L (CRN),
including 2 vent valves (AISI 316L)
3 1/4 – 18 NPT, mounting: PN 160: M10, PN 420: M12, Alloy C (CRN)

PMD75 order code

→ For continuation of PMD75 ordering information, see the following page.

70 Endress+Hauser
Deltabar S

PMD75 (continued) 80 Seal:

A FKM Viton
C PTFE
F NBR
K Copper seal ring, cleaned for oxygen service
1 FKM Viton, cleaned from oil and greace
2 FKM Viton, cleaned for oxygen service
Note application limits pressure/temp.
3 PTFE, cleaned for oxygen service
H Copper seal ring

100 Additional option 1:

A not selected
E SIL2/IEC 61508 Declaration of conformity
B Material test certificate for wetted components, inspection certificate as per EN
10204 3.1 acc. to specification 52005759
C NACE MR0175 (wetted parts)
D Material test certificate for wetted components as per EN 10204 3.1 and NACE
MR0175 material, inspection certificate as per EN 10204 acc. to specification
52010806
M Overvoltage protection
N HistoROM/M-DAT
S GL/ABS marine certificate
V Mounting on shut-off valve from above
W Mounting on shut-off valve from below
2 Test report acc. to EN10204 2.2
3 Routine test with certificate, inspection certificate as per EN 10204 3.1
4 Overpressure test with certificate, inspection certificate as per EN 10204 3.1

110 Additional option 2:

A not selected
E SIL2/IEC 61508 Declaration of conformity
B Material test certificate for wetted components, inspection certificate as per
EN 10204 3.1 acc. to specification 52005759
G Separate housing, cable length see additional spec. + mounting bracket,
wall/pipe, 316L
K Vent valves (2 pieces), Alloy C
L Vent valves (4 pieces), Alloy C
M Overvoltage protection
N HistoROM/M-DAT
R Screws 7/16 UNF, length 1 1/2" (4 pieces) for oval flange adapter PZO
S GL/ABS marine certificate
U Mounting bracket for wall/pipe, AISI 304
2 Test report acc. to EN10204 2.2
3 Routine test with certificate, inspection certificate as per EN 10204 3.1
4 Overpressure test with certificate,
inspection certificate as per EN 10204 3.1
5 Helium leak test EN 1518 with test certificate inspection certificate as per
EN 10204 3.1

PMD75 complete order code

Endress+Hauser 71
 Deltabar S

FMD76 This overview does not mark options which are mutually exclusive.

10 Approval:
A For non-hazardous areas
➀ 1 ATEX II 1/2 G EEx ia IIC T6
6 ATEX II 1/2 G EEx ia IIC T6, overspill protection WHG
2 ATEX II 1/2 D EEx ia IIC T6
8 ATEX II 1 GD EEx ia IIC T6
– + E
➁ 3 ATEX II 1/2 GD EEx ia IIC T6
7 ATEX II 3 G EEx nA II T6
S FM IS, Class I, II, III Division 1, Groups A – G; NI Class I Division 2, Groups A – D; AEx ia
R FM NI, Class I, Division 2, Groups A – D
U CSA IS, Class I, II, III Division 1, Groups A – G; Class I Division 2, Groups A – D, Ex ia
H NEPSI Ex ia IIC T6
I IECEx Zone 0/1 Ex ia IIC T6

20 Output; Operation:
➂ A 4...20 mA HART, SIL operation outside, LCD (→ see Fig. ➀, o)
B 4...20 mA HART, SIL operation inside, LCD (→ see Fig. ➀, p)
➃ C 4...20 mA HART, SIL operation inside (→ see Fig. p)
M PROFIBUS PA, operation outside, LCD (→ see Fig. ➁, o)
1 2
N PROFIBUS PA, operation inside, LCD (→ see Fig. n, p)
PC

HART
R
O PROFIBUS PA, operation inside (→ see Fig. p)
250002271-–

FIELD COMMUNICATION PROTOCOL

P FOUNDATION Fieldbus, operation outside, LCD (→ see Fig. n, o)

HW-Version: 1
SW-Version: 2

Q FOUNDATION Fieldbus, operation inside, LCD (→ see Fig. n, p)

R FOUNDATION Fieldbus, operation inside (→ see Fig. p)

30 Housing; Cable entry, Protection:

A Aluminium T14 housing, optional display on the side, IP 66/67/NEMA 6P, Gland M 20x1.5
B Aluminium T14 housing, optional display on the side, IP 66/67/NEMA 6P, Thread G 1/2
C Aluminium T14 housing, optional display on the side, IP 66/67/NEMA 6P, Thread 1/2 NPT
T15 D Aluminium T14 housing, optional display on the side, IP66/67/NEMA 6P, M12x1 PA plug
E Aluminium T14 housing, optional display on the side, IP 66/67/NEMA 6P, 7/8" FF plug
T14 F Aluminium T14 housing, optional display on the side, IP 65/NEMA 4X, Han7D plug, 90°
J Aluminium T15 housing, optional display on the top, IP 66/67/NEMA 6P, Gland M 20x1.5
K Aluminium T15 housing, optional display on the top, IP 66/67/NEMA 6P, Thread G 1/2
L Aluminium T15 housing, optional display on the top, IP 66/67/NEMA 6P, Thread 1/2 NPT
M Aluminium T15 housing, optional display on the top, IP 66/67/NEMA 6P, M 12x1 PA plug
N Aluminium T15 housing, optional display on the top, IP 66/67/NEMA 6P, 7/8" FF plug
P Aluminium T15 housing, optional display on the top, IP 65/NEMA 4X, Han7D plug, 90°
T17
1 AISI 316L T14 housing, optional display on the side, IP 66/67/NEMA 6P, Gland M 20x1.5
2 AISI 316L T14 housing, optional display on the side, IP 66/67/NEMA 6P, Thread G 1/2
3 AISI 316L T14 housing, optional display on the side, IP 66/67/NEMA 6P, Thread 1/2 NPT
4 AISI 316L T14 housing, optional display on the side, IP 66/67/NEMA 6P,M 12x1 PA plug
5 AISI 316L T14 housing, optional display on the side, IP 66/67/NEMA 6P, 7/8" FF plug
6 AISI 316L T14 housing, optional display on the side, IP 65/NEMA 4X, Han7D plug, 90°
R AISI 316L T17 housing, optional display on the side, IP 66/68/NEMA 6P, Gland M 20x1.5
S AISI 316L T17 housing, optional display on the side, IP 66/68/NEMA 6P, Thread G 1/2
T AISI 316L T17 housing, optional display on the side, IP 66/68/NEMA 6P, Thread 1/2 NPT
U AISI 316L T17 housing, optional display on the side, IP 66/68/NEMA 6P, , M 12x1 PA plug
V AISI 316L T17 housing, optional display on the side, IP 66/68/NEMA 6P, 7/8" FF plug
Z Housing: see additional specifications

40 Nominal range; PN:

Nominal value PN
7D 100 mbar/10 kPa/1.5 psi 16 bar/1,6 MPa/240 psi
7F 500 mbar/50 kPa/7.5 psi 100 bar/10 MPa/1500 psi
7H 3 bar/300 kPa/45 psi 100 bar/10 MPa/1500 psi

FMD76 order code

→ For continuation of FMD76 ordering information, see the following page.

72 Endress+Hauser
Deltabar S

FMD76 (continued) 50 Calibration; Unit:

1 Nominal range; mbar/bar
2 Nominal range; kPa/MPa
3 Nominal range; mmH2O/mH2O
4 Nominal range; inH2O/ftH2O
6 Nominal range; psi
B Customised; see additional specification
C Factory certificate 5-point; see additional specification
D DKD certificate; see additional specification
K Platinum; see additional specification
L Platinum and factory certificate 5-point; see additional specification
M Platinum and DKD certificate: see additional specification

70 Process connection low-pressure side; Material; Seal:

Mounting: 7/16 – 20 UNF
B 1/4 – 18 NPT IEC 61518, C22.8, FKM Viton (CRN)
D 1/4 – 18 NPT IEC 61518, AISI 316L, FKM Viton (CRN)
F 1/4 – 18 NPT IEC 61518, Alloy C, FKM Viton (CRN)
G 1/4 – 18 NPT IEC 61518, PVDF, FKM Viton,
Safety instructions, observe electrostatic charge.
K 1/4 – 18 NPT IEC 61518, AISI 316L, EPDM (CRN)
L 1/4 – 18 NPT IEC 61518, Alloy C, EPDM (CRN)
M 1/4 – 18 NPT IEC 61518, AISI 316L, Kalrez (CRN)
N 1/4 – 18 NPT IEC 61518, Alloy C, Kalrez (CRN)
P 1/4 – 18 NPT IEC 61518, AISI 316L, Chemraz (CRN)
Q 1/4 – 18 NPT IEC 61518, Alloy C, Chemraz (CRN)
S 1/4 – 18 NPT IEC 61518, AISI 316L, FKM Viton, cleaned from oil and greace (CRN)
T 1/4 – 18 NPT IEC 61518, AISI 316L, FKM Viton, cleaned for oxygen service (CRN)
U RC 1/4, AISI 316L, FKM Viton (CRN)

80 Process connection high-pressure side; Material:

EN/DIN flanges
B DN 80 PN 10-40 B1, AISI 316L
D DN 80 PN 10-40, AISI 316L with ECTFE coating
Safety instructions, observe electrostatic charge!
E DN 80 PN 10-40 B1, Alloy C276
F DN 100 PN 10-16 B1, AISI 316L
G DN 100 PN 25-40 B1, AISI 316L
H DN 100 PN 25-40, AISI 316L with ECTFE coating
Safety instructions, observe electrostatic charge!
J DN 100 PN 25-40 B1, Alloy C276
L DN 100 PN 10-16, AISI 316L with ECTFE coating
Safety instructions, observe electrostatic charge!
M DN 100 PN 10-16 B1, Alloy C276
ANSI flanges
P 3" 150 lbs RF, AISI 316/316L (CRN)
R 3" 150 lbs, AISI 316/316L with ECTFE coating
Safety instructions, observe electrostatic charge!
S 3" 150 lbs RF, Alloy C276 (CRN)
T 4" 150 lbs RF, AISI 316/316L (CRN)
U 4" 150 lbs, AISI 316/316L with ECTFE coating
Safety instructions, observe electrostatic charge!
V 4" 150 lbs RF, Alloy C276 (CRN)
W 4" 300 lbs RF, AISI 316/316L (CRN)
JIS flanges
1 10K 80A RF, AISI 316L
3 10K 80A RF, Alloy C276
4 10K 100A RF, AISI 316L

FMD76 order code

→ For continuation of FMD76 ordering information, see the following page.

Endress+Hauser 73
 Deltabar S

FMD76 (continued) 100 Additional option 1:

A not selected
E SIL2/IEC 61508 Declaration of conformity
B Material test certificate for wetted components, inspection certificate as per
EN 10204 3.1 acc. to specification 52005759
M Overvoltage protection
N HistoROM/M-DAT
S GL/ABS marine certificate
2 Test report acc. to EN10204 2.2
3 Routine test with certificate, inspection certificate as per EN 10204 3.1
4 Overpressure test with certificate, inspection certificate as per EN 10204 3.1

110 Additional option 2:

A not selected
E SIL2/IEC 61508 Declaration of conformity
G Separate housing, cable length see additional spec. + mounting bracket,
wall/pipe, 316L
K Vent valves (2 pieces), Alloy C
M Overvoltage protection
N HistoROM/M-DAT
R Screws 7/16 UNF, length 1 1/2" (4 pieces) for oval flange adapter PZO
S GL/ABS marine certificate
U Mounting bracket for wall/pipe, AISI 304
2 Test report acc. to EN10204 2.2
3 Routine test with certificate, inspection certificate as per EN 10204 3.1
4 Overpressure test with certificate, inspection certificate as per EN 10204 3.1
5 Helium leak test EN 1518 with test certificate, inspection certificate as per
EN 10204 3.1

FMD76 complete order code

74 Endress+Hauser
Deltabar S

FMD77 This overview does not mark options which are mutually exclusive.

10 Approval:
A For non-hazardous areas
1 ATEX II 1/2 G EEx ia IIC T6
6 ATEX II 1/2 G EEx ia IIC T6, overspill protection WHG
2 ATEX II 1/2 D
4 ATEX II 1/3 D
8 ATEX II 1 GD EEx ia IIC T6
3 ATEX II 1/2 GD EEx ia IIC T6
5 ATEX II 2 G EEx d IIC T6
7 ATEX II 3 G EEx nA II T6
S FM IS, Class I, II, III Division 1, Groups A – G; NI Class I Division 2, Groups A – D; AEx ia
T FM XP, Class I Division 1, Groups A – D; AEx ia
Q FM DIP, Class II, III Division 1, Groups E – G
➀ R FM NI, Class I, Division 2, Groups A – D
U CSA IS, Class I, II, III Division 1, Groups A – G; Class I Division 2, Groups A – D, Ex ia
V CSA XP, Class I Division 1, Groups B – D; Ex d
W CSA Class II, III Division 1, Groups E – G (Dust-Ex)

– + E
➁ G NEPSI Ex d IIC T6
H NEPSI Ex ia IIC T6
I IECEx Zone 0/1 Ex ia IIC T6
B Combined certificates: ATEX II 1/2 G EEx ia IIC T6 + II G EEx d IIC T6
C Combined certificates: FM IS and XP Class I Division 1, Groups A – D
D Combined certificates: CSA IS and XP Class I Division 1, Groups A – D
E Combined certificates: FM/CSA IS and XP Class I Division 1, Groups A – D
F Combined certificates: ATEX II EEx ia / EEx d + FM/CSA IS + XP; ATEX II 1/2G EEx ia IIC T6+; ATEX II 2G EEx d IIC
T6+; FM/CSA IS + XP Cl.I Div.1 Gr.A-D

20 Output; Operation:
➂ A 4...20 mA HART, SIL operation outside, LCD (→ see Fig. ➀, o)
B 4...20 mA HART, SIL operation inside, LCD (→ see Fig. ➀, p)
➃ C 4...20 mA HART, SIL operation inside (→ see Fig. p)
M PROFIBUS PA, operation outside, LCD (→ see Fig. ➀, o)
1 2
N PROFIBUS PA, operation inside, LCD (→ see Fig. ➀, p)
PC

HART
R
O PROFIBUS PA, operation inside (→ see Fig. p)
250002271-–

FIELD COMMUNICATION PROTOCOL

P FOUNDATION Fieldbus, operation outside, LCD (→ see Fig. n, o)

HW-Version: 1
SW-Version: 2

Q FOUNDATION Fieldbus, operation inside, LCD (→ see Fig. n, p)

R FOUNDATION Fieldbus, operation inside (→ see Fig. p)

30 Housing; Cable entry, Protection:

T14 A Aluminium T14 housing, optional display on the side, IP 66/67/NEMA 6P, Gland M 20x1.5
B Aluminium T14 housing, optional display on the side, IP 66/67/NEMA 6P, Thread G 1/2
C Aluminium T14 housing, optional display on the side, IP 66/67/NEMA 6P, Thread 1/2 NPT
D Aluminium T14 housing, optional display on the side, IP 66/67/NEMA 6P, M12x1 PA plug
T15 E Aluminium T14 housing, optional display on the side, IP 66/67/NEMA 6P, 7/8" FF plug
F Aluminium T14 housing, optional display on the side, IP 65/NEMA 4X, Han7D plug, 90°
J Aluminium T15 housing, optional display on the top, IP 66/67/NEMA 6P, Gland M 20x1.5
K Aluminium T15 housing, optional display on the top, IP 66/67/NEMA 6P, Thread G 1/2
L Aluminium T15 housing, optional display on the top, IP 66/67/NEMA 6P, Thread 1/2 NPT
M Aluminium T15 housing, optional display on the top, IP 66/67/NEMA 6P, M 12x1 PA plug
+ – N Aluminium T15 housing, optional display on the top, IP 66/67/NEMA 6P, 7/8" FF plug
T17 P Aluminium T15 housing, optional display on the top, IP 65/NEMA 4X, Han7D plug, 90°
1 AISI 316L T14 housing, optional display on the side, IP 66/67/NEMA 6P, Gland M 20x1.5
2 AISI 316L T14 housing, optional display on the side, IP 66/67/NEMA 6P, Thread G 1/2
3 AISI 316L T14 housing, optional display on the side, IP 66/67/NEMA 6P, Thread 1/2 NPT
4 AISI 316L T14 housing, optional display on the side, IP 66/67/NEMA 6P, M 12x1 PA plug
5 AISI 316L T14 housing, optional display on the side, IP 66/67/NEMA 6P, 7/8" FF plug
6 AISI 316L T14 housing, optional display on the side, IP 65/NEMA 4X, Han7D plug, 90°
R AISI 316L T17 housing, optional display on the side, IP 66/68/NEMA 6P, Gland M 20x1.5
S AISI 316L T17 housing, optional display on the side, IP 66/68/NEMA 6P, Thread G 1/2
T AISI 316L T17 housing, optional display on the side, IP 66/68/NEMA 6P, Thread 1/2 NPT
U AISI 316L T17 housing, optional display on the side, IP 66/68/NEMA 6P, M 12x1 PA plug
V AISI 316L T17 housing, optional display on the side, IP 66/68/NEMA 6P, 7/8" FF plug
Z Housing: see additional specifications

FMD77 order code

→ For continuation of FMD77 ordering information, see the following page.

Endress+Hauser 75
 Deltabar S

FMD77 (continued) 40 Nominal range; PN:

Nominal value PN
7D 100 mbar/10 kPa/1.5 psi 160 bar/16 MPa/2400 psi
7F 500 mbar/50 kPa/7.5 psi 160 bar/16 MPa/2400 psi
7H 3 bar/300 kPa/45 psi 160 bar/16 MPa/2400 psi
7L 16 bar/1.6 MPa/240 psi 160 bar/16 MPa/2400 psi

50 Calibration, Units:
1 Calibration: nominal range, mbar/bar
2 Calibration: nominal range, kPa/MPa
3 Calibration: nominal range, mmH2O/mH2O
4 Calibration: nominal range, inH2O/ftH2O
6 Calibration: nominal range, psi
B Custom calibration: see additional specification
C Factory calibration: see additional specification, Factory calibration certificate, 5-point
D DKD calibration: see additional specification

60 Membrane material (high-pressure side):

1 AISI 316L
2 Alloy C
3 Monel
5 Tantalum
6 AISI 316L with Gold-Rhodium coating
7 AISI 316L with 0.09 mm PTFE foil (not for vacuum applications)

70 Process connection low-pressure side; Material; Seal:

Mounting: 7/16 – 20 UNF
B 1/4 – 18 NPT IEC 61518, C22.8, FKM Viton (CRN)
D 1/4 – 18 NPT IEC 61518, AISI 316L, FKM Viton (CRN)
F 1/4 – 18 NPT IEC 61518, Alloy C276, FKM Viton (CRN)
H 1/4 – 18 NPT IEC 61518, AISI 316L, PTFE+C4-ring (CRN)
J 1/4 – 18 NPT IEC 61518, Alloy C, PTFE+C4-ring (CRN)
K 1/4 – 18 NPT IEC 61518, AISI 316L, EPDM (CRN)
L 1/4 – 18 NPT IEC 61518, Alloy C, EPDM (CRN)
M 1/4 – 18 NPT IEC 61518, AISI 316L, Kalrez (CRN)
N 1/4 – 18 NPT IEC 61518, Alloy C, Kalrez (CRN)
P 1/4 – 18 NPT IEC 61518, AISI 316L, Chemraz (CRN)
Q 1/4 – 18 NPT IEC 61518, Alloy C, Chemraz (CRN)
S 1/4 – 18 NPT IEC 61518, AISI 316L, cleaned from oil and greace (CRN)
T 1/4 – 18 NPT IEC 61518, AISI 316L, cleaned for oxygen service (CRN)
U RC 1/4, AISI 316L, FKM Viton (CRN)

80 Process connection high-pressure side; Material:

EN/DIN flanges
A DN 50 PN 10-40 B1, AISI 316L
B DN 80 PN 10-40 B1, AISI 316L
C DN 80 PN 10-40 B1, extended diaphragm seal: 50 mm/100 mm/200 mm,
extended diaphragm seal: see additional specification
F DN 100 PN 10-16 B1, AISI 316L
G DN 100 PN 25-40 B1, AISI 316L
ANSI flanges
N 2" 150 lbs, RF, AISI 316/316L (CRN)
P 3" 150 lbs, RF, AISI316/ 316L (CRN)
Q 3" 150 lbs RF, AISI 316/316L, extended diaphragm seal: 2"/4"/6"/8", extended
diaphragm seal: see additional specification
T 4" 150 lbs RF, AISI 316L (CRN)
W 4" 300 lbs RF, AISI 316L (CRN)
JIS flanges
X 10K 50A RF, AISI 316L
1 10K 80A RF, AISI 316L
4 10K 100 A RF, AISI 316L

FMD77 order code

→ For continuation of FMD77 ordering information, see the following page.

76 Endress+Hauser
Deltabar S

FMD77 (continued) 90 Fill fluid:

A Silicone oil
D Vegetable oil
L Low temperature oil
V High-temperature oil
F Inert oil

100 Additional options 1:

A Additional options 1 not selected
B Material test certificate for wetted components, inspection certificate as per
EN 10204 3.1 acc. to specification 52005759
C NACE MR0175 material
D Material test certificate for wetted components as per EN 10204 3.1 and
NACE MR0175 material, inspection certificate as per EN 10204 acc. to
specification 52010806
M Overvoltage protection
N HistoROM module
2 Test report acc. to EN 10204 2.2
3 Routine test with certificate, inspection certificate as per EN 10204 3.1
4 Overpressure test with certificate,
inspection certificate as per EN 10204 3.1

110 Additional options 2:

A Additional options 2 not selected
E SIL2/IEC 61508 declaration of conformity
G Separate housing, cable length see additional spec. + mounting
bracket, wall/pipe, 316L
M Overvoltage protection
N HistoROM module
R Screws 7/16 UNF, length 1 1/2" (4 pieces) for oval flange adapter
PZO
2 Test report acc. to EN 10204 2.2
3 Routine test with certificate,
inspection certificate as per EN 10204 3.1
4 Overpressure test with certificate,
inspection certificate as per EN 10204 3.1

FMD77 complete order code

Endress+Hauser 77
 Deltabar S

FMD78 This overview does not mark options which are mutually exclusive.

10 Approval:
A For non-hazardous areas
1 ATEX II 1/2 G EEx ia IIC T6
6 ATEX II 1/2 G EEx ia IIC T6, overspill protection WHG
2 ATEX II 1/2 D
4 ATEX II 1/3 D
8 ATEX II 1 GD EEx ia IIC T6
3 ATEX II 1/2 GD EEx ia IIC T6
5 ATEX II 2 G EEx d IIC T6
7 ATEX II 3 G EEx nA II T6
S FM IS, Class I, II, III Division 1, Groups A – G; NI Class I Division 2, Groups A – D; AEx ia
T FM XP, Class I Division 1, Groups A – D; AEx ia
Q FM DIP, Class II, III Division 1, Groups E – G
➀ R FM NI, Class I, Division 2, Groups A – D
U CSA IS, Class I, II, III Division 1, Groups A – G; Class I Division 2, Groups A – D, Ex ia
V CSA XP, Class I Division 1, Groups B – D; Ex d
W CSA Class II, III Division 1, Groups E – G (Dust-Ex)

– + E
➁ G NEPSI Ex d IIC T6
H NEPSI Ex ia IIC T6
I IECEx Zone 0/1 Ex ia IIC T6
B Combined certificates: ATEX II 1/2 G EEx ia IIC T6 + II G EEx d IIC T6
C Combined certificates: FM IS and XP Class I Division 1, Groups A – D
D Combined certificates: CSA IS and XP Class I Division 1, Groups A – D
E Combined certificates: FM/CSA IS and XP Class I Division 1, Groups A – D
F Combined certificates: ATEX II EEx ia / EEx d + FM/CSA IS + XP; ATEX II 1/2G EEx ia IIC T6+; ATEX II 2G EEx d IIC
T6+; FM/CSA IS + XP Cl.I Div.1 Gr.A-D

20 Output; Operation:
➂ A 4...20 mA HART, SIL operation outside, LCD (→ see Fig. ➀, o)
B 4...20 mA HART, SIL operation inside, LCD (→ see Fig. ➀, p)

➃ C 4...20 mA HART, SIL operation inside (→ see Fig. p)

M PROFIBUS PA, operation outside, LCD (→ see Fig. ➀, o)
1 2
N PROFIBUS PA, operation inside, LCD (→ see Fig. ➀, p)
PC

O PROFIBUS PA, operation inside (→ see Fig. p)

HART
R
250002271-–

P FOUNDATION Fieldbus, operation outside, LCD (→ see Fig. n, o)

FIELD COMMUNICATION PROTOCOL

HW-Version: 1
SW-Version: 2

Q FOUNDATION Fieldbus, operation inside, LCD (→ see Fig. n, p)

R FOUNDATION Fieldbus, operation inside (→ see Fig. p)

30 Housing; Cable entry, Protection:

T14 A Aluminium T14 housing, optional display on the side, IP 66/67/NEMA 6P, Gland M 20x1.5
B Aluminium T14 housing, optional display on the side, IP 66/67/NEMA 6P, Thread G 1/2
C Aluminium T14 housing, optional display on the side, IP 66/67/NEMA 6P, Thread 1/2 NPT
D Aluminium T14 housing, optional display on the side, IP 66/67/NEMA 6P, M12x1 PA plug
E Aluminium T14 housing, optional display on the side, IP 66/67/NEMA 6P, 7/8" FF plug
+ – F Aluminium T14 housing, optional display on the side, IP 65/NEMA 4X, Han7D plug, 90°
T15 J Aluminium T15 housing, optional display on the top, IP 66/67/NEMA 6P, Gland M 20x1.5
K Aluminium T15 housing, optional display on the top, IP 66/67/NEMA 6P, Thread G 1/2
L Aluminium T15 housing, optional display on the top, IP 66/67/NEMA 6P, Thread 1/2 NPT
M Aluminium T15 housing, optional display on the top, IP 66/67/NEMA 6P, M 12x1 PA plug
N Aluminium T15 housing, optional display on the top, IP 66/67/NEMA 6P, 7/8" FF plug
P Aluminium T15 housing, optional display on the top, IP 65/NEMA 4X, Han7D plug, 90°
T17 1 AISI 316L T14 housing, optional display on the side, IP 66/67/NEMA 6P, Gland M 20x1.5
2 AISI 316L T14 housing, optional display on the side, IP 66/67/NEMA 6P, Thread G 1/2
3 AISI 316L T14 housing, optional display on the side, IP 66/67/NEMA 6P, Thread 1/2 NPT
4 AISI 316L T14 housing, optional display on the side, IP 66/67/NEMA 6P, M 12x1 PA plug
5 AISI 316L T14 housing, optional display on the side, IP 66/67/NEMA 6P, 7/8" FF plug
6 AISI 316L T14 housing, optional display on the side, IP 65/NEMA 4X, Han7D plug, 90°
R AISI 316L T17 housing, optional display on the side, IP 66/68/NEMA 6P, Gland M 20x1.5
S AISI 316L T17 housing, optional display on the side, IP 66/68/NEMA 6P, Thread G 1/2
T AISI 316L T17 housing, optional display on the side, IP 66/68/NEMA 6P, Thread 1/2 NPT
U AISI 316L T17 housing, optional display on the side, IP 66/68/NEMA 6P, M 12x1 PA plug
V AISI 316L T17 housing, optional display on the side, IP 66/68/NEMA 6P, 7/8" FF plug
Z Housing: see additional specifications

FMD78 order code

→ For continuation of FMD78 ordering information, see the following page.

78 Endress+Hauser
Deltabar S

FMD78 (continued) 40 Nominal range; PN:

Nominal value PN
7D 100 mbar/10 kPa/1.5 psi 160 bar/16 MPa/2400 psi
7F 500 mbar/50 kPa/7.5 psi 160 bar/16 MPa/2400 psi
7H 3 bar/300 kPa/45 psi 160 bar/16 MPa/2400 psi
7L 16 bar/1,6 MPa/240 psi 160 bar/16 MPa/2400 psi
7M 40 bar/4 MPa/600 psi 160 bar/16 MPa/2400 psi

50 Calibration, Units:
1 Calibration: nominal range, mbar/bar
2 Calibration: nominal range, kPa/MPa
3 Calibration: nominal range, mmH2O/mH2O
4 Calibration: nominal range, inH2O/ftH2O
6 Calibration: nominal range, psi
B Custom calibration: see additional specification
C Factory calibration: see additional specification, Factory calibration certificate, 5-point
D DKD calibration: see additional specification, DKD-Certificate

60 Membrane material:
1 AISI 316L
2 Alloy C
3 Monel
5 Tantalum
6 AISI 316L with Gold-Rhodium coating
7 AISI 316L with 0.09 mm PTFE foil (not for vacuum applications)

80 Process connection, Material:

Membrane diaphragm seal cell structure
UF Cell DN 50 PN 16-400, AISI 316L
UH Cell DN 80 PN 16-400, AISI 316L
UJ Cell DN 100 PN 16-400, AISI 316L
VF Cell 2" 150-2500 lbs, AISI 316L (CRN)
VH Cell 3" 150-2500 lbs, AISI 316L (CRN)
VJ Cell 4" 150-2500 lbs, AISI 316L (CRN)
Threaded connections
GA Thread ISO 228 G 1/2 B, PN 40, AISI 316L, separator, PTFE seal
RL Thread ANSI 1/2 MNPT, PN 40, AISI 316L, separator, PTFE seal
Clamp connections
TB Tri-Clamp, ISO 2852 DN 25 (1"), DIN 32676 DN 25, 3A, AISI 316L
TC Tri-Clamp, ISO 2852 DN 25 – DN 38 (1 – 1 1/2"), 3A, AISI 316L
TD Tri-Clamp, ISO 2852 DN 40 – DN 51 (2")/DN 50, 3A, AISI 316L
TF Tri-Clamp, ISO 2852 DN 70 – DN 76.1 (3"), 3 A, AISI 316L
Pipe diaphragm seal Clamp
SB Tri-Clamp, ISO 2852 DN 25 (1"), 3A, AISI 316L
SC Tri-Clamp, ISO 2852 DN 38 (1 1/2"), 3A, AISI 316L, 3.1 + P
ressure test acc. to PED Cat. II
SD Tri-Clamp, ISO 2852 DN 51 (2"), 3A, AISI 316L, 3.1 + Pressure test acc. to PED Cat. II
Hygienic connections
TR Varivent model N for pipes DN 40 – DN 162, PN 40, 3A, AISI 316L
TK DRD DN50 (65 mm), PN 25, 3A, AISI 316L
WH Sanitary tank spud, 3A, AISI 316L, extended diaphragm seal 2"
MR DIN 11851 DN 50 PN 25, 3A, AISI 316L
MS DIN 11851 DN 65 PN 25, 3A, AISI 316L
MT DIN 11851 DN 80 PN 25, 3A, AISI 316L
M3 DIN 11851 DN 50 PN 25 socket, 3A, AISI 316L
M4 DIN 11851 DN 65 PN 25 socket, 3A, AISI 316L
M5 DIN 11851 DN 80 PN 25 socket, 3A, AISI 316L
EN/DIN flanges
B3 DN 50 PN 10-40 B1, AISI 316L
B5 DN 80 PN 10-40 B1, AISI 316L
BT DN 100 PN 10-16 B1, AISI 316L
B6 DN 100 PN 25-40 B1, AISI 316L

FMD78 order code

→ For continuation of FMD78 ordering information, see the following page.

Endress+Hauser 79
 Deltabar S

FMD78 (continued) 80 Process connection, Material (continued):

ANSI flanges
AF 2" 150 lbs RF, AISI 316/316L (CRN)
AR 2" 300 lbs RF, AISI 316/316L (CRN)
AG 3" 150 lbs RF, AISI 316/16L (CRN)
AS 3" 300 lbs RF, AISI 316/316L (CRN)
J4 3" 150 lbs RF, AISI 316/316L, extended diaphragm seal: 2"/4"/6"/8" (CRN),
extended diaphragm seal: see additional specification
AH 4" 150 lbs RF, AISI 316/316L (CRN)
AT 4" 300 lbs RF, AISI 316/316L (CRN)
J5 4" 150 lbs RF, AISI 316/316L, extended diaphragm seal: 2"/4"/6"/8" (CRN),
extended diaphragm seal: see additional specification
JIS flanges
KF 10K 50A RF, AISI 316L
KL 10K 80A RF, AISI 316L
KH 10K 100A RF, AISI 316L

90 Capillary, Fill fluid:

1 ...m capillary, silicone oil
2 ...m capillary, vegetable oil
3 ...m capillary, high temperature oil
4 ...m capillary, oil for oxygen service
5 ...m capillary, low temperature oil
A ...ft capillary, silicone oil
B ...ft capillary, vegetable oil
C ...ft capillary, high temperature oil
D ...ft capillary, oil for oxygen service
E ...ft capillary, low temperature oil

100 Additional options 1:

A Additional options 1 not selected
B Material test certificate for wetted components, inspection certificate as per
EN 10204 acc. to specification 52005759
C NACE MR0175 material
D Material test certificate for wetted components as per EN 10204 3.1 and
NACE MR0175 material, inspection certificate as per EN 10204 acc. to
specification 52010806
M Overvoltage protection
N HistoROM module
S GL/ABS marine certificate
2 Test report acc. to EN 10204 2.2
3 Routine test with certificate, inspection certificate as per EN 10204 3.1
4 Overpressure test with certificate,
inspection certificate as per EN 10204 3.1

110 Additional options 2:

A Additional options 2 not selected
E SIL2/IEC61508 Declaration of conformity
G Separate housing, cable length see additional spec. + mounting bracket,
wall/pipe, 316L
M Overvoltage protection
N HistoROM module
S GL/ABS marine certificate
U Mounting bracket for wall and pipe, AISI 304
2 Test report acc. to EN 10204 2.2
3 Routine test with certificate, inspection certificate as per EN 10204 3.1
4 Overpressure test with certificate,
inspection certificate as per EN 10204 3.1

FMD78 complete order code

80 Endress+Hauser
Deltabar S

Further documentation
Innovation • Cerabar S/Deltabar S/Deltapilot S,
For process pressure, differential pressure, flow and level measurement: IN010P/00/en

Field of Activities • Pressure measurement: Powerful instruments for process pressure, differential pressure, level and flow:
FA004P/00/en

Technical Information • Cerabar S: TI383P/00/en

• Deltapilot S: TI416P/00/en
• Deltatop/Deltaset: TI297P/00/en
• EMC test basic principles: TI241F/00/en

Operating Instructions 4...20 mA HART:

• Deltabar S: BA270P/00/en
• Description of device functions Cerabar S/Deltabar S/Deltapilot S,
Pressure and Differential pressure transmitters: BA274P/00/en
PROFIBUS PA:
• Deltabar S: BA294P/00/en
• Description of device functions Cerabar S/Deltabar S/Deltapilot S,
Pressure and Differential pressure transmitters: BA296P/00/en
FOUNDATION Fieldbus:
• Deltabar S: BA301P/00/en
• Description of device functions Cerabar S/Deltabar S, Pressure and Differential pressure transmitters:
BA303P/00/en

Brief operating instructions • 4...20 mA HART, Deltabar S: KA1018P/00/en

• PROFIBUS PA, Deltabar S: KA1021P/00/en
• FOUNDATION Fieldbus, Deltabar S: KA1024P/00/en

Manual for Functional Safety • Deltabar S (4...20 mA): SD189P/00/en

(SIL)

Safety Instructions Certificate/Type of Device Electronic insert Documentation

Protection

ATEX II 1/2 G EEx ia IIC T6 PMD70, PMD75, – 4...20 mA HART, – XA235P

FMD76, FMD77, PROFIBUS PA,
FMD78 FOUNDATION Fieldbus

ATEX II 1/2 D PMD70, PMD75, – 4...20 mA HART – XA237P

FMD77, FMD78 – PROFIBUS PA, – XA280P
FOUNDATION Fieldbus
ATEX II 1/2 D EEx ia IIC T6 FMD76 – 4...20 mA HART – XA238P
– PROFIBUS PA, – XA281P
FOUNDATION Fieldbus
ATEX II 1/3 D PMD70, PMD75, – 4...20 mA HART – XA239P
FMD77, FMD78 – PROFIBUS PA, – XA282P
FOUNDATION Fieldbus

ATEX II 2 G EEx d IIC T6 PMD70, PMD75, – 4...20 mA HART, – XA240P

FMD77, FMD78 PROFIBUS PA,
FOUNDATION Fieldbus

ATEX II 3 G EEx nA II T6 PMD70, PMD75, – 4...20 mA HART, – XA241P

FMD76, FMD77, PROFIBUS PA,
FMD78 FOUNDATION Fieldbus

ATEX II 1/2 GD PMD70, PMD75, – 4...20 mA HART, – XA243P

EEx ia IIC T6 FMD76, FMD77, PROFIBUS PA,
FMD78 FOUNDATION Fieldbus

ATEX II 1 GD EEx ia IIC T6 PMD70, PMD75, – 4...20 mA HART, – XA275P

FMD76, FMD77, PROFIBUS PA,
FMD78 FOUNDATION Fieldbus

Endress+Hauser 81
 Deltabar S

Certificate/Type of Device Electronic insert Documentation

Protection

ATEX II 1/2 G EEx ia IIC T6 PMD75, FMD77, – 4...20 mA HART, – XA242P

+ ATEX II 2 G EEx d IIC T6 FMD78 PROFIBUS PA,
FOUNDATION Fieldbus

ATEX II EEx ia / EEx d + PMD75, FMD77, – 4...20 mA HART, – in preparation

FM/CSA IS + XP FMD78 PROFIBUS PA,
ATEX II 1/2G EEx ia IIC T6+ FOUNDATION Fieldbus
ATEX II 2G EEx d IIC T6+
FM/CSA IS + XP Cl.I Div.1
Gr.A-D

Certificate/Type of Device Electronic insert Documentation

Protection

IECEx Zone 0/1 Ex ia IIC T6 PMD70, PMD75, – 4...20 mA HART, – XB004P

FMD76, FMD77, PROFIBUS PA,
FMD78 FOUNDATION Fieldbus

Certificate/Type of Device Electronic insert Documentation

Protection

NEPSI Ex ia IIC T6 PMD70, PMD75, – 4...20 mA HART, – XC004P

FMD76, FMD77, PROFIBUS PA,
FMD78 FOUNDATION Fieldbus

NEPSI Ex d IIC T6 PMD75, FMD77, – 4...20 mA HART, – XC006P

FMD78 PROFIBUS PA,
FOUNDATION Fieldbus

Installation/Control Drawings Certificate/Type of Device Electronic insert Documentation

Protection

FM IS Class I, II, III, PMD70, PMD75, – 4...20 mA HART – ZD141P

Division 1, Groups A – G; FMD76, FMD77, – PROFIBUS PA, – ZD188P
NI, Class I Division 2, FMD78 FOUNDATION Fieldbus
Groups A – D; AEx ia
CSA IS Class I, II, III, PMD70, PMD75, – 4...20 mA HART – ZD142P
Division 1, Groups A – G; FMD76, FMD77, – PROFIBUS PA, – ZD189P
Class I Division 2, FMD78 FOUNDATION Fieldbus
Groups A – G

FM IS + XP Class I, PMD75, FMD77, – 4...20 mA HART – ZD186P

Division 1, Groups A – D FMD78 – PROFIBUS PA, – ZD190P
FOUNDATION Fieldbus

CSA IS + XP Class I, PMD75, FMD77, – 4...20 mA HART – ZD153P

Division 1, Groups A – D FMD78 – PROFIBUS PA, – ZD191P
FOUNDATION Fieldbus

FM/CSA IS + XP Class I, PMD75, FMD77, – 4...20 mA HART – ZD153P + ZD186P

Division 1, Groups A – D FMD78 – PROFIBUS PA, – ZD190P + ZD191P
FOUNDATION Fieldbus

ATEX II EEx ia / EEx d + PMD75, FMD77, – 4...20 mA HART, – in preparation

FM/CSA IS + XP FMD78 PROFIBUS PA,
ATEX II 1/2G EEx ia IIC T6+ FOUNDATION Fieldbus
ATEX II 2G EEx d IIC T6+
FM/CSA IS + XP Cl.I Div.1
Gr.A-D

Overspill protection • WHG: ZE260P/00/de

82 Endress+Hauser
Deltabar S

Endress+Hauser 83
 Deltabar S

Instruments International

Endress+Hauser
Instruments International AG
Kaegenstrasse 2
4153 Reinach
Switzerland

Tel. +41 61 715 81 00

Fax +41 61 715 25 00
www.endress.com
[email protected]

TI382P/00/en/12.07
No. 71060097
CSS/FM+SGML 6.0 71060097